Search Documents

By J. Moore, D. Gault, R. V. Lugn

Impact of small projectiles with velocities between 0.9 and 7.3 km per sec on basalt produce craters chiefly by the ejection of fragments. Weight-size distributions of the ejecta are linear for part of the size range of the fragments. Cumulative weight-size distributions of the ejecta from different craters vary because of erratic formation of large fragments and a large percentage of ejecta below 0.1 mm. In the range of velocities studied, the crater depth is approximately proportional to the 0.75 power of velocity of the projectile. This relationship may represent a transition regime between the fluid impact regime and the undeformed projectile impact regime. The volumes per unit of projectile energy of the craters produced are comparable to those reported for lower speed projectile impact and drill bits. An experimental investigation of projectile impact on rock is being conducted jointly by the Ames Research Center of the National Aeronautics and Space Administration and the U.S. Geological Survey. Projectiles are launched with light-gas guns at the Ballistics Range of the Ames Research Center. The craters and ejecta produced in these experiments are being studied by the U.S. Geological Survey. Steel, aluminum and polyethylene projectiles weighing from 0.25 to 0.015 g were accelerated to velocities of 0.88 km per sec (2,900 fps) to 7.3 km per sec (24,000 fps) with a light-gas gun, using hydrogen as the propellant medium. Projectiles impacted the targets normal to plane rock surfaces in an atmosphere of air with a nominal pressure of 25 to 50 mm of mercury. The metal projectiles were mounted in supporting four-piece nylon sabots, which guided the projectiles down the launching tube. After launch, aerodynamic drag acted to separate the sabots from the projectiles. Impact velocities were determined with time measurements and spark photographs of the projectiles in flight. Ejecta were collected in lucite and aluminum containers placed around the target block. A small hole in the containers permitted projectile entry. Impact of projectiles of the size employed produced craters in the rock targets chiefly by ejection of fragments. The craters are small, roughly conical depressions with crushed and intensely fractured rock at the bottoms of the depressions. The ejecta are composed of pieces of the projectile and rock fragments ranging in size from a few tenths of a micron or less to several centimeters in maximum dimension. In this paper, the structural features of the craters, the weight-size distributions of the recovered ejecta, and crater depth and crater volume relationships are described. DESCRIPTION OF CRATERS Typical craters (Fig. 1) produced by experimental projectile impact in basalt are shallow, wide base

Jan 1, 1963

By J B. Magee

Sheep Creek Mines Limited has developed several operating techniques that have greatly assisted in keeping unit costs at reasonable levels. Some of the techniques, as described in this paper, include organization, accounting, warehousing, bonus and contracts. INTRODUCTION THIS paper is a non-technical report on operating techniques developed by Sheep Creek Mines Limited at their Mineral King mine, located near lnvermere, B.C. Depressed metal prices and continually rising labour and materials costs have necessitated a continuous search for method to keep operating costs down. The newly developed techniques and practices have greatly assisted in maintaining unit costs. Sheep Creek Mines Limited is a mining company incorporated under the laws of the Province of British Columbia. The Company's share capital is 3,500,000 common shares, witl1 a par value of 50 cents each, of which there are 1,875 000 shares is-sued. The Company has eight di-rectors. The administration, exploration and accounting offices are located in Nelson, B.C. The Company's working capital is approximately $1,500,000.

Jan 1, 1963

PRODUCTION of cesium, cesium salts, and rubidium salts in the United States declined somewhat from 1961 levels; rubidium production was virtually unchanged. Imports of pollucite declined because consumption was supplied partially out of inventory. Domestic Production.-About 50 tons of pollucite was reported mined at the Tin Mountain mine in the Black Hills of South Dakota. The Dow Chemical Co., Midland, Mich., MSA Research Corp., Callery, Pa., and Penn Rare Metals, Inc., Revere, Pa., produced a total of 159 pounds of cesium. Rubidium production remained essentially the same as in 1961. Shipments of the two metals by these companies and by American Potash & Chemical Corp., Trona, Calif., totaled 279 pounds. Production of cesium and rubidium salts by American Potash & Chemical Corp., Penn Rare Metals, Inc., and Rocky Mountain Research, Inc., Denver, Colo., declined substantially during 1962.

Jan 1, 1963

By G. S. Scott

The flammability of trichloroethylene vapors in air has been determined in a 7-inch cyclindrical vessel. Saturated flammable mixtures were formed with air at atmospheric pressure between 30° C (86° F) and 82° C (180° F); the trichloroethylene concentrations at these temperatures are 12.5 (lower) and 90 (upper) volume-percent, respectively. Further study is necessary to assess the effects of different variables on the flammability of this material. INTRODUCTION Trichloroethylene (TCE) (ClHC = CCl2), sold under various trade names (Blacosolv, Perm-A-Clor, Tri, Triad, Triclene, Trivec, Tromex, Vapoclean, Vapoclor, Westrosol, etc.), is an important industrial chemical. A summary of its physical and chemical properties is given in table 1. It is used to degrease metals, leather, and textiles, to extract residual oils from vegetable oil cakes, for dry cleaning, and in soap. It is a powerful solvent for fats, resins, bitumens, rubber, sulfur, and phosphorus. Several explosions in which trichloroethylene was involved prompted an investigation by the Bureau of Mines to determine the conditions under which such accidents can occur.

Jan 1, 1963

By R. Bakish, M. A. Badiali, N. W. Kirshenbaum

One pound of ultra pul-e molybdenum has been produced containing both metallic and nonmetallic impuvities close to or less than the limits of detection. various purification methods were investigated; althouglz the use of move than one purification step was consideved, it was found that a single, caefully-controlled sublimation of MoCl5 yielded a highly puvified product without prior treatment or recourse to repeated sublimation. Hydrogen reduction of MoC1, to metal was attempted at atmospheric pressure; however, reduced pressure was necessary to obtain substantial yields. The tubular deposits of metal were consolidated into bulk fovm by electron beam melting undev high vacuum yielding a very low gas content. Boblems involved in monitoring the puvity of these materials and analytical results obtained are also presented. THE pronounced effect of even trace amounts of impurities upon fundamental properties of materials is well known to metallurgists and solid-state physicists. Consequently, groups interested in basic studies of metals have in recent years immensely stimulated the preparation and production of numerous ultra-pure metals. Increased demand by scientists for these high purity materials has necessitated development of facilities to prepare them in significant quantities; the procedures reported here were devised to produce significant quantities of ultra-pure molybdenum. Previous work performed in the field of vapor phase purification and hydrogen reduction of several other refractory metal chlorides had demonstrated valuable techniques applicable to molybdenum.' Various purification and reduction steps were individually investigated. Those procedures which showed the most favorable results with respect both to attainment of high purity and to ease of operation were then incorporated in the process utilized to produce the metal.' STARTING MATERIALS It is well known that because of differences in volatility, chlorides may be separated by fractional distillation. It was presumed that distillation of molybdenum pentachloride offered a simple and straightforward method of purification due to its relatively low boiling point. Alternatively, sublimation of the solid chloride also appeared feasible since MoC15 has both a reasonably narrow temperature range in which it exists as a liquid (a property typical of refractory metal chlorides) and a low enthalpy of sublimation. Pertinent thermochemical data of MoC15 are given in Table I. It should be noted that this compound must be handled with care as it is extremely hygroscopic. Anhydrous MoC15 was obtained from the A Metal Climax Co. METHODS OF PURIFYING MOLYBDENUM PENTACHLORIDE Distillation. It was expected that distillation methods, while affording an efficient purification, would prove simple to control and would have a higher production rate than sublimation processes. Also considered was the possibility of effecting a high degree of purification by using both these volatilization methods in conjunction—possibly a distillation followed by sublimation of the solidified condensate. Distillation of MoC15 was investigated using a single stage distillation column packed with chemically resistant glass beads. Heating coils were wound around the column and collection tube (condenser). As-received MoCl5 was charged into a flask connected with the column using a side loading arm under an argon flow. After the column and condenser were brought to about 270" and 210°C, respectively, the apparatus was lowered until the flask was fully immersed in a constant temperature fused salt bath maintained at about 285 °C. Distillation was continued for about 10 or 15 min until 50 to 70 g of distillate had been collected. Analyses of these distillations indicated that several elements, e.g., Cu, Fe, Ni, Cr, and Mg, were lowered in quantity although not all were removed to the same extent. The occurrence of Na, B, Si, and A1 in the distillates appeared to be due to contamination, possibly from corrosion of the pyrex glass. An improved distillation system of larger capacity and longer distilling column was built. Improvements were effected in lowering the amounts of such impurities as B, Mn, Ni, Na, Mg, Cr, Cu, and Fe. These studies were pursued concomitantly with efforts to purify by sublimation; it was subsequently found that although improvements in purity were obtained by distillation, sublimation processes were simpler to control and effected a high degree of purity.

Jan 1, 1963

By Laird Crocker

This report describes a study of beryllium recovery from sulfate leach liquor by di-2-ethylhexyl phosphate (EHPA) solvent extraction in conjunction with caustic stripping. The work was one phase of Bureau of Mines research on process development for Spor Mountain, Utah, ores. Solution for the solvent extraction studies was prepared by sulfuric acid leaching of ore containing 0.6 pet BeO, Before solvent extraction of beryllium, the leach liquor was treated to prevent coextraetion of iron by either (1) removal of ferric iron by amine solvent extraction or (2) reduction of ferric iron to nonextractable ferrous iron by treatment with sulfur dioxide. Beryllim was extracted from the aqueous leach liquor by countercurrent multistage contacting with a kerosine solution of EHPA. The loaded organic solution was stripped with sodim hydroxide solution. Subsequently, beryllium hydroxide was precipitated by boiling the sodium beryllate strip solution and converted to beryllium oxide of 98 pct BeO-grade by calcining. Material of this grade can be directly processed into beryllium-copper alloy or be used as starting material for further refining to produce high-purity, nuclear-grade beryllium. Over 90 pct of the beryllium contained in the leach liquor was recovered as beryllia.

Jan 1, 1963

By T. H. Alden

Using alternating tension-compression straining, the hardening of magnesium oxide single crystals was studied up to large stresses and strains. At 0.25 pct plastic strain amplitude, the hardening curve is approximately linear with slope 25,000 psi from the shear yield stress, 7 to 8000 psi, to 35,000psi. Above this stress, the slope decreases. The strain hardening behavior of MgO is considered qualitatively similar to that of metal single crystals. The relatively high stress attainable by strain hardening is associated apparently with the high yield stress on the cross-slip system, (001) <110>. Cleavage fracture during testing is uncommon. It is argued that the centers of high internal stress at glide band intersections, at which cracks tend to nucleate, are dispersed by cyclic strain. Special features of the glide band structure produced by cyclic strain and revealed by dislocation etch pits, support this view. Strain hardened MgO has mechanical properties greatly superior to the as-received material: yield stress, greater than 100,000 psi; elongation to fracture about 1 pct. A material is said to strain harden if the yield stress increases with an increment of plastic strain. This definition is usually applied for straining done in one direction, but is also applicable when the strain direction is periodically reversed, Fig. 1. For certain metal single crystals, data are available which permit a comparison of the hardening behavior for cyclic straining and for tension straining.&apos;-4 With certain qualifications, these data show that the same processes of hardening are operative in each type of test.5 Despite this fact, the importance of the technique is not immediately evident, although tension-compression studies of the common metals appear to suggest some deficiencies in theories of strain hardening developed exclusively on the basis of tensile tests. However, a recent observation suggests that the cyclic straining method may be very useful for studying semibrittle crystals in which large plastic strains are not accessible in unidirectional testing. The observation is that zinc crystals, when strained in tension-compression at -52°C, do not fail by cleavage at low stress (-500 psi)6 as they do in tension, but harden to a limiting stress of more than 5000 psi over a total plastic strain of about 600 pct.2 An important characteristic of the behavior of zinc crystals is the high stress, relative to the yield stress, attainable by strain hardening. By comparison, the hardening of aluminum single crystals tested by an identical technique saturates at 1100 psi. This difference is best explained by the cross-slip hypothesis of dynamic recovery.7,8 In zinc, cross slip is difficult because of the high yield stress for glide on planes other than the basal plane in the < 1120 > zone. The present work was undertaken in order to test whether these methods and ideas are applicable to other materials. Magnesium oxide single crystals, in common with most crystals of the rock-salt structure, deform plastically but fail by cleavage after a small strain when tested in tension. It was hoped that larger strains would be attained using tension-compression. There is, in addition, evidence 8a which shows that slip on the probable cross system, (001) < 110>, is difficult in magnesium oxide; it may therefore be possible to attain high stresses by strain hardening. 1) EXPERIMENTAL PROCEDURE Experimental methods used in this study were based in part on techniques reported in papers of Stokes, Johnston, and Li.&apos; MgO blocks, purchased from Norton Co., were used without further annealing. Specimens were cleaved to dimensions approximately 0.125 in. sq and 1 in. in length. The gage section, formed by chemical polishing, was sprinkled with 280 mesh silicon carbide particles in order to introduce fresh dislocations. The crystals were then cemented into cylindrical aluminum adapters and clamped in an Instron testing machine. One of two alternating straining programs was used. In the first, total cross-head travel was established and increased in steps after various numbers of cycles. In the second, a capacitance gage was used to directly measure the elongation of the specimen and the crosshead was controlled so as to keep the plastic strain amplitude constant. The straining was always symmetrical with respect to the initial, zero strain condition. While both procedures produce strain hardening, only the latter permits a measure of the total plastic strain so that hardening curves may be drawn. Constant plastic strain amplitude tests were done

Jan 1, 1963

By Arnulf Muan, Egil Aukrust

Activities of COO in the three solid solution series COO-MgO, COO-MnO, and COO-"FeO" have been determined at 1200°C by equilibrating oxide samples with a metal phase (cobalt or a Co-Fe alloy) in atmospheres of known oxygen activities. The systems COO-MgO and COO-MnO are ideal, within limits of experimental error, whereas the system COO-"FeO" shows a slight positive deviation from ideality at the temperature of this investigation. KNOWLEDGE of activities of oxide components in solid solutions is necessary for the calculation of the cation distribution among coexisting oxide phases in many important metallurgical, ceramic, and geochemical systems. Very few activity-composition curves are available for such systems at the present time. A start on the prodigious job of obtaining such data has been made by studies of solid solutions with simple sodium chloride type structure containing NiO or "FeO" as a component.1-3 The present paper describes similar studies for solid solutions with sodium chloride type structure containing COO as a component. For the systems COO-MgO and COO-MnO, the activity solid solution is determined by the equation Here po and are the oxygen activities of the gas phase in equilibrium with the phase assemblages metallic cobalt plus oxide solid solution, and metallic cobalt plus pure COO, respectively. In the system CoO-"Fe07&apos;, the metal phase is a Co-Fe alloy rather than pure cobalt. In this case the activity of COO in the oxide solid solution is calculated from the equation where a& is the activity of cobalt in the metal phase. Because the system Co-Fe is close to ideal4 and the metal phase appearing in the present work contains less iron than cobalt even at the lowest COO concentrations of the oxide phases used may be set equal to N . Hence, Eq. [2] becomes The value of Nc, can be estimated from the relative stabilities of the oxides COO (see below) and I) EXPERIMENTAL METHOD Two different but closely related procedures were used in the present investigation to determine the activity-composition curves. In one method, the oxide solid solutions were equilibrated against

Jan 1, 1963

By S G. Bergdahl

Underground mining in Sweden is today characterized by mechanization and automation, owing to the rising cost of labour. Drilling in drifts and tunnels is still essentially done with jackleg drills, but rigs wh1ch make it possible for one man to operate two or more drills are now frequently used. Large jumbos for longhole drilling, with two drills operated by one man, are used, especially in sub-level caving. A special drill-rig for drilling through overburden and blasting without removing the overburden has been successfully used in canals and also in ports, where blasting is per-formed under water. The increased use of mining methods based upon long blastholes is a result of the development of equipment for drilling long straight holes. The most common mining method in Sweden is sub-level caving. Extensive research, with model tests, has been carried out in order to determine suit-able dimensions of drifts, sub-levels and drilling patterns. The results have been tried in practice and have given increased yield and less waste rock in hoisted ore.

Jan 1, 1963

By F. J. Smit, S. C. Sun

Flotation variables were investigated for the re-clamation of phosphate from a Florida washer slime. Under optimum conditions, 92% of the phosphate was recovered. Further cleaning of the rougher flotation concentrate resulted in a product containing about 30% P2O5 with a phosphate recovery of 65%. The enormous amount of slimes rejected in the Florida pebble phosphate fields, containing roughly one-third of the phosphate in the pebble matrix,1 has long been considered as a serious problem to the industry. The mere disposal of these slimes has posed an almost insurmountable task for several investigators.2-5 Some companies still resort to huge surface dams, some covering 1800 acres, for slime disposal.6 Information on the recovery of fine phosphate from these slimes is scanty. Dry separation8 and electrostatic beneficiation8 were suggested, but would necessitate radical changes in the present mining and concentration methods. Haseman10 proposed the selective flocculation of colloidal phosphate with starch, while Ralston11 suggested the removal of clay from the matrix by amine flotation. Leaching of the slimes for recovering the small amount of uranium was attempted by the Battelle Memorial Institute12,13 but proved to be economically unfeasible. The purpose of the present investigation was to determine the optimum fatty-acid flotation conditions for reclaiming the phosphate discarded with the Bartow washer slime. Prior to the flotation experimerits, however, the size distribution and the minera-logical composition of the employed slime had to be determined.

Jan 1, 1963

By J. E. Jennings

The problems of slope stability in open-cast mines are examined. A criterion, the instantaneous stripping ratio, is suggested for use in the design of pit slopes and as an index of control at all stages of the exploitation of the ore body, This criterion may also be related to safety and to the maximizing of profits. Two approaches to safe design of slopes, one from the point of view of soil mechanics and the other from the point of view of rock mechanics, are described and critically compared. The effect on slope stability of the regional tectonic stress field is discussed. Explanation is given of the application of the Terzaghi effective stress concept to problems in both soil and rock environments, including possible effects when borehole deformation techniques are used to measure stresses in rock in situ.

Jan 1, 1963

By F. X. Spiegel, D. Bardos, Paul A. Beck

Ti6NileSi7)G is known to be cubic, with 116 atoms in the unit cell. In the present work four new G sili-cides were found with other transition elements and five G germanides. The titanium-group elements are very efficient in forming G phases. The vanadium -group elements are somewhat less efficient, and the chromium-group elements do not form any. Cobalt can replace nickel in most cases, but it is somewhat less efficient. Iron was not found to form any G phases. Germanium is somewhat less efficient than silicon. The (TiNiSi)E phase has been previously identified by Westbrook. However, its crystal structure has not been determined. In the present work the E phase was found to have an orthorhombic unit cell with lattice parameters a. = 7.02, bo = 5.18, co = 11.11A. A large number of other E phases were found at the same stoicheometric ratio in ternary systems of silicon and germanium with transition elements. Lattice parameters similar to those for TiNiSi were measured. The number of atoms per unit cell is estimated at 30 to 36. The vanadium-group elements are somewhat more efficient in forming the E phase than the titanium-group elements. Chromium-group elements were not found to form any E phases. Cobalt is somewhat less efficient than nickel, and iron is less efficient than cobalt. Germanium is not as efficient as silicon. ThE ternary silicide designated as G-phase was first identified by Beattie and versnyder1 and by Beattie and Hagel2 at the approximate composition TiNi2Si. Westbrook et al.&apos; gave the composition as Ti2Ni7Sis. This phase was found to be fcc with a. = 11.201A and 116 atoms per unit cell. Beattie4 and more recently independently Hladishevskii, Kripyakevich, Kuzma, and Teslyuk5 were able to show that this structure is isotypic with MgeSi7CuLe and Th6Mn23. The latter structures had been determined by Florio, Rundle, and snow,&apos; Nagorsen and Witte,7 and Bergman and Waugh.8 According to the crystal structure, Ti8Ni6Si7 may be considered as the ideal composition. The Russian investigators5 identified six additional ternary phases isotypic with Ti6Ni6Si7, in which titanium is replaced by Mn, V, Nb, Ta, Zr, and Hf, and one, namely MneNil6Ge7, in which germanium replaces silicon. They also found that Cr6Ni6Si7, which does not occur as a ternary phase, can be stabilized by replacing 1 at. pct of the Cr by V, Mn, or Ta. Another ternary silicide was found by Westbrook et al.3 at the composition TiNiSi, and it was designated by them as the E phase. The crystal structure of this phase has not been deter-

Jan 1, 1963

By P. T. Brooks

The selective recovery of nickel and cobalt from impure raw materials is being investigated by the Bureau of Mines as part of a program to develop improved procedures for preparation of pure metals. A combination solvent extraction-electrolytic process has been developed in the laboratory that enables preparation of high-quality nickel and cobalt from nickel oxide containing, in percent, 76 nickel, 0.8 cobalt, 0.5 magnesium, 0.2 iron, and lesser quantities of copper, zinc, and other metals. The oxide was smelted, using carbon as reductant, and cast into anodes. These anodes subsequently were dissolved in diaphragm-type electrolytic cells. Nickel and cobalt were deposited separately from appropriate electrolytes, concurrent with dissolution of the impure anodes. Anolyte containing nickel and cobalt in the form of chlorides and sulfates was treated for removal of impurities and separation of nickel and cobalt. First, iron and aluminum were removed as hydroxides by adding nickel hydroxide to raise the pH of the anolyte from 2.3 to 4.5. Next, the pH was adjusted to 2 by adding hydrochloric acid, and the solution was treated by solvent extraction to separate nickel and cobalt.

Jan 1, 1963

By Lancucki C. J, Nickson N. M

X-ray diffraction and differential thermal methods were used to determine the mineralogy of some clays used by the heavy clay industry in the Adelaide area. A detailed analysis was made of the mineralogy and particle size distribution of eighteen samples from beds in two pits in the Recent sediments in the Adelaide plains, of six white clays developed from the weathering of the Adelaide series of sediments, and of four Recent alluvial clays from a pit in the Mount Lofty ranges south of Adelaide. Structural clay products in the Adelaide area are manufactured from mixtures of these clays, so the mineralogy and particle size distribution was determined of eighteen clay mixtures used to make red bricks, cream bricks, facing bricks, pipes and tiles.Knowledge of this mineralogy is important in understanding the ceramic behaviour of the clays.INTRODUCTIONIn this investigation an account is given of the clay mineralogy and particle size distribution of some ceramic clays from the Adelaide area. The clays are used in the manufacture of structura,l clay products and the results to &apos;be described are part of an overall &apos;plan of study covering the heavy industrial clays and shales of Australia. Previous work has been published (Cole and Carthew, 1953; Ferguson, 1954; Ferguson and Hosking, 1955; Cole and Nielsen, 1958/59).In this work no attempt has been made to examine clays from all pits engaged in supplying materials for the structural clay industry. However, in 1954 the senior author collected detailed samples from two pits working in Recent alluvial clays in the Allenby&#183;Gardens and Beverley areas near...

Jan 1, 1963

By W. E. Robinson

Samples of raw oil shale and kerogen concentrates were oxidized by alkaline potassium permanganate, air, nitric acid, oxygen, and ozone to obtain information about the chemical structure of organic kerogen in oil shale. In one test, oil shale and oil-shale products were oxidized exhaustively with alkaline potassium permanganate, and the distribution of the organic carbon in the final oxidation products was determined. Comparing results of this oxidation with those obtained from other carbonaceous materials and known compounds gave information about the structure of kerogen. Alkaline potassium permanganate oxidation also was used partly to degrade kerogen into soluble products for characterization purposes. Structures present in these degradation products were indicative of type structures originally present in the kerogen. Nitric acid, oxygen, and ozone were used also for partly degrading kerogen to soluble oxidation products. Carbon-balance oxidation tests using alkaline potassium permanganate showed that Colorado oil-shale kerogen differs from many other carbonaceous materials such as coal and kerogens from other areas. Composition of the degradation products indicated that Colorado oil-shale kerogen is predominantly cycloparaffinic and saturated heterocyclic structures with some long-chain paraffinic and aromatic structures present. The ring systems may be connected through short carbon chains or bridges containing oxygen, nitrogen, and sulfur.

Jan 1, 1963

There is an alternative theory of the high grade orebodies of the Middleback Group, based on the primary nature of the high grade ores in an area of carbonate deposition, with lesser amounts of siliceous and aluminous sediments. The environment is thought to have been unstable, possibly volcanic, and to have been a subsiding basin, substantially isolated from the open sea.Jaspilites, iron bearing talc rocks and iron bearing carbonate rocks were derived from the primary sediments by metasomatic alteration after metamorphism.The metasomatic agents were carbon dioxide and water vapour which were mobilized from the primary dolomite and reacted with a metamorphically produced group of iron bearing and iron free amphiboles, forming talc and progressively releasing silica and iron oxides from the iron amphiboles.The talc rocks in turn released silica which reconstituted jaspilites into their present 200 ft thick crust or zone.The theory accounts for the present disposition of a jaspilite zone over a talc zone which in turn overlies a carbonate zone, and accounts for the down dip changes found in bores which penetrate these zones.INTRODUCTIONIron Duke (Fig. 1) lies some 34 miles south west of WhyalIa in South Australia, and is the most southerly ore body in the Middleback Ranges.The Middleback Ranges are divided into a northern range and a southern range meridionally disposed and separated by an erosion gap called Kimba Gap.The South Middleback Range contains four orebodies;Iron Duke at the southern extremity, Iron Duchess north of Iron Duke and on the same ridge, Iron Knight also on the same ridge, which has been breached by erosion between theDuchess and Knight orebodies, and north east of Iron Knight, the Iron Chieftain.Cook&apos;s Range is the eastern range of the South Middleback Range and no large orebodies are known to occur there.

Jan 1, 1963

The CSIRO acid alumina employs the essential steps of digestion, hydrolysis and calcination to produce pure alumina from ores too high in silica or too low in grade for the Bayer process. The two latter stages have been described in some detail previously but the digestion stage requires separate dis-cussion since ores vary widely in composition and reactivity. Kaolinitic clays require. roasting to 8000C to render the alumina soluble in the 11 per cent sulphuric acid used in the process while some ferruginous laterites require roasting to reduce the reactivity of iron minerals. The iron content of pregnant solutions is kept at a low figure by digesting at temperatures where the solubilities of ferric oxide or basic ferric sulphates are small. A.two-stage, counter-current digestion is necessary to extract a high percentage of alumina from the ores and to pro-duce a basic pregnant liquor, with an S03:Al203 ratio of 1. 9 suitable for high temperature hydrolysis. The second stage of digestion, called the modification stage, treats slightly acid liquors with exces&apos;s of ore in the temperature range 1200- 1400C. The first stage operates at 1700-190 C to extract further alumina from modification residues, using recycled acid obtained from later steps of the process. Both temperature ranges are critical for economic operation and for proper con-trol of the iron content of solutions. In batch experiments, thirty minutes is regarded as a suitable retention time for digestion and modification; ores which require much longer than this are less suitable for the process. Impurities. such assilica, titanium and vanadium oxides are discarded in the residue along with iron oxide and do not contaminate the final product. Bivalent metallic sulphates such as MgSO4 can build up in the circuit to a very considerable degree without affecting. product purity.Comparison with other processes shows that the C. S. I. R. O. process is superior for control of contamination by iron, which is the major problem in acid processes. The pure intermediate product (3 A1203. 4 S03. 9 H2O) is also more convenient for cal-cination to alumina than the hydrated aluminium sulphate usually recovered in other processes. Detailed cost comparisons must await pilot-plant evaluation of the C. S. I. R. O. process.

Jan 1, 1963

By A. H. Daane, B. J. Beaudry

The Sc-Y and Sc-Zr systems were studied by thermal and X-ray methods. Both systems are characterized by complete solid solubility in the low temperature hexagonal form and in the high temperature bcc form. In the Sc-Y system, there is a minimum in the solidus at 50 at. pct and 1365°C, while the solidus in the Sc-Zr system follows a nearly straight line relationship between the melting point of scandium and zirconium. There is a minimum in the temperature of transition from hexagonal to bcc in the Sc-Y system at 43 at. pct Y and 1175°C; while the temperature of transition is raised in the Sc-Zr system to a maximum of 1415 °C at 30 at. pct Zr. INTEREST in the metals of the first transition series has usually stemmed from their useful properties; however, there is now a great deal of interest in determining the fundamental nature of these metals. Since scandium is the first of these transition metals, a study of the preparation and Properties1 and the alloying behavior of scandium2 was initiated. In a continuing study of the alloying behavior of scandium, the systems of scandium with zirconium and yttrium have been established. Extensive solid solubility in both the Sc-Zr and Sc-Y systems was expected from application of the classical rules of Hume-Rothery. Also, the modified Darken and Gurry plot as suggested by Gschneid-ner3 showed ideal conditions for solubility in the Sc-Zr system with less favorable conditions in the Sc-Y system. The effect of scandium on the transformation temperature of zirconium and yttrium was of interest, since a recent empirical observation by Uly and Burr4 predicted that the solute scandium would raise the transformation temperature of zirconium and lower the yttrium transformation. In addition to noting the validity of the above predictions, the SC-Y and Sc-Zr systems were established. EXPERIMENTAL METHODS Materials. The metals employed in this investigation were crystal bar zirconium, distilled scandium prepared by the method described by Spedding, et al.1 and yttrium prepared by the method described by Carlson, et a1.5 The major impurities present in these metals are listed in Table I in ppm. Alloy Preparation. All the alloys examined were initially formed by comelting the two metals in a nonconsumable electrode arc-melting furnace under an atmosphere of purified helium or argon. The buttons were inverted at least five times and re-melted each time to ensure homogeneity. During preparation of Sc-Zr alloys, approximately 1 wt pct was lost which was attributed entirely to the loss of scandium by distillation. When preparing Sc-Y alloys, approximately 1.5 wt pct was lost, but it was assumed that the intended composition was maintained, since the relative weight lost when arc melting the component metals was nearly the same. Samples weighing 15 to 20 g were prepared for time-temperature thermal analysis, while only 1- to 2-g samples were prepared for the optical pyrometer and X-ray diffraction studies. Thermal Methods. The solidus and the melting points of the metals were determined by an optical pyrometer method described previously.2 The temperatures at which the transformation from hexagonal to bcc occurs were determined by differential thermal analysis. Several points on the solidus and liquidus in the Sc-Y system were also determined by this method and are in good agreement with those obtained by the optical pyrometer method. The procedure followed in the preparation of samples for thermal analysis and the furnace used have been described elsewhere.2&apos;6 Since a limited quantity of scandium was available, most of the alloys were not melted during thermal analysis, thus avoiding contamination by the crucible. The alloy could then be reused and the composition changed by adding the desired quantity of solute to obtain the next alloy. Heat Treatment and X-Ray Methods. In order to ensure homogeneity, the "as arc-melted" alloys Were wrapped in tantalum foil, sealed in quartz capsules and heated at 1100°C for 15 hr and then cooled at a rate of 8 deg per min. Samples for X-ray diffraction were filed from these heat-treated alloys, sealed in 1/8 in. by 1/2 in. tantalum capsules under

Jan 1, 1963

By Pablo Hadzeriga

There are two places in the world where potash, trade name for potassium chloride, is economically recovered from naturally occuring brines by solar evaporation. One is at the Dead Sea and the other at Wendover, Utah. American Potash and Chemical at Trona, California recovers potash from natural brines, but uses fuel to accomplish evaporation. Under proper meteorological conditions the use of solar evaporation might be desirable from the economical standpoint. Of course, this may not be true when, if by artificial evaporation, a group of very valuable salts are recovered. This is the case of the American Potash operation at Trona. Solar evaporation has its limits. The working temperature is low. We may say, just to cover most areas of the world where solar evaporation may be practical, that it will take place between 18°C and perhaps around 45°C. In most cases the average working temperature expected will be around 25°C.

Jan 1, 1963

This paper deals briefly with the geology and mineralisation of the Ediacara Mineral Field, which is located about 300 miles north of Adelaide in the Mount James Range.The field was discovered sane time prior to 1872. Total recorded production for the field amounts to a few hundred tons of lead and 36 tons of copper. Re-listing of the field during 1961-62 led to its classification as a Mississippi Valley type deposit. Diamond drilling has partly outlined the spread of mineralisation and confirmed its stratiform distribution,Sources for the metals are suggested and various possible mechanisms. of deposition are described.

Jan 1, 1963