Search Documents

By E. J. Harris

Mathematical solutions to complex mine ventilation problems are possible, but often the airway network is so complex that the mathematical solution becomes tedious and impractical. A fluid network analyzer, designed and built for analyzing mine ventilation problems has been in service at the Bureau of Mines' Pittsburgh station for approximately nine years. Using this analogue as a model, the mine ventilation network is simulated electrically by a combination of series and parallel circruits laid out to conform with actual mine airways. A tungsten filament lamp, referred to as a Fluistor, is used to simulate mine airway resistance. With the analogue ventilation model established, voltages of the proper amplitude to represent ventilating pressures are impressed across the circuit at points where mine fans and airshafts are located. Comparison of mathematical solutions of complex systems against analogue results showed a maximum variance of 3% for pressures and 2% for quantities. An electrical fluid network analyzer, designed and built especially for analyzing mine ventilation distribution problems, has been in service at the Bureau of Mines, Pittsburgh, for approximately nine years. It is a nonlinear, low voltage, fluid network analyzer of the type developed by the late Malcolm S. McIlroy, Professor of Electrical Engineering, Cornell University, who cooperated with G. E. McElroy, of the Bureau of Mines, in adapting the instrument to mine ventilation systems. Several modifications have been made since the original installation, but a considerable part of this paper is drawn from G. E. McElroy's original description of the analogue.' The analysis of water or gas distribution systems2,3 led to the development of this type of network analyzer. Several similar units are now employed by utility companies for this purpose; however, the Bureau of Mines unit is the only one designed specifically for mine airflow problems. Other airflow analogues employing a similar principle have been used at the Central Research Station of the Netherlands State Mines,4 in England,5 and in South Africa.6 Information on these devices indicated they were somewhat inflexible because commercial lamps with a sufficient range of resistance are difficult to obtain. Computers for mine ventilation analysis have been developed in Germany which instead of lamps use a variable resistance to adjust for turbulent flow laws. These units are expensive, but excellent results have been reported in their application. THE ANALYZER Theory of Application: As airflow generally follows the law of turbulent fluid flow, resistance to flow is nonlinear; consequently, the problem has been to find a nonlinear resistance element of suitable range that can be used for electrically simulated airflow. Tungsten filament lamps operated on alternating or direct current approximate the square-law resistance characteristics of mine airflow over a large range below maximum or rated voltage; that is, the voltage drop varies approximately as the square of the current. Consequently, the heart of the network analyzer is a nonlinear resistor known as a Fluistor, which is simply a custom-made low voltage, tungsten filament lamp that is available in a progressive series of relative resistance values ranging from 0.05 to 500 in nominal 5% steps. However, variations in manufacturing large groups result in differences of 1 to 3%, but series arrangements required for high-loss branches can be matched within about 1%. Utilizing a combination of Fluistors and load circuits, the mine ventilation system is duplicated electrically. Intake load circuits are connected from power intake to primary points of the circuit network; segments of unregulated flow along intakes and returns are represented by Fluistors, regulated splits and leakage paths are represented by load circuits and Fluistors of proper capacity; and mine exhausts are connected to ground from the last point of the network to complete the circuit. For the special purpose of representing booster fans or natural draft conditions, boosters or separate source circuits are provided that can be inserted between any two points of a network to increase voltage to the required value. Physical Layout: The analyzer consists of three 42

Jan 1, 1963

By E O. Foster

When roasting started at Giant Yellowknife Mines in 1949, it became apparent that, to prevent air and water pollution in the surrounding district, it would be necessary to collect the arsenic that was contained in the exit gases of the roaster. The arsenic collection problem was finally solved by the installation of both electrostatic and baghouse collectors. It was realized that a considerable quantity of gold-bearing dust was leaving the roaster with the exit gases. When the collection problem was solved, it was possible to measure this loss. The loss proved to be considerable and it became evident that a substantial quantity of gold could be recovered. Research programs on dust treatment began in 1958, and by May, 1960, the treatment process which is currently being followed was started in the plant. At present, the two electrostatic preci11itators, Operated at temperatures above 600°F, collect the gold-bearing dust.

Jan 1, 1963

By Chester T. Sims

RECENTLY, a new type of superalloy material called TD Nickel* has been marketed.' It is a sim- ple, two-phased alloy, consisting of thoria particles dispersed in nickel of rather high purity (Ni-2 pct Thoz). Its mechanical properties appear relatively superior to previous experimental material attempting to use the oxide nonmetallic dispersion concept (except SAP), and superior to conventional nickel-base alloys at high homologous temperatures. This is derived from an interesting method of creating the dispersion, arising during chemical processing of the nickel and thorium salts in solution while reducing the nickel to metal. An evaluation of the thoria phase was conducted at this laboratory. Material and Procedure. TD Nickel was made available, consisting of several inches of 0.470-in. rod, extruded at a ratio of 64: 1, straightened, and centerless ground. Property determinations on this rod by the supplier at 1800°F showed an ultimate tensile strength of 11,400 psi, yield strength of 9600 psi, and 6 pct elongation. Specimens were removed from the rod for as-extruded metallography, and two 1/2-in. lengths supported on high-purity Al2O9 bricks were placed in a laboratory muffle furnace for exposure at 2000° F. The furnace door was left cracked to allow a slight amount of circulation. One specimen was removed at 200 hr for examination; the other was left for 2000 hr. Metallography. The micro structures obtained for the three conditions of exposure are shown in Fig. 1. Elongation of the grain structure in the extrusion direction is readily evident. The grains appear to be up to 0.001 in. (0.003 cm) long, with a length/width ratio of about 10: 1. Allowing for modest local in-homogeneities in structure, no significant change in thoria particle size or nickel alloy grain size occurred during the 2000°F exposure. However, etching depth varies slightly from one specimen to another, changing the number of particles visible. The thoria dispersion appears to be in the order of 0.01 (min) to 0.5 (max) p diam. The minimum diameter is difficult to estimate at X10,000, and may be less. Interparticle spacing appears to be about 0.1 p. Etching effects can be seen, depending upon grain orientation. A cubic etch-pit pattern appears in certain grains, apparently when etching is started by an anodic particle of thoria, Fig. l(c). The cubic pattern appears related to crystallographic orientation, and is prominent when the [ l00 ] direction is perpendicular to the plane of polish. The grains which present a ridged appearance in the photograph appear to be oriented with the [110} direction perpendicular to the plane of polish. Analysis. The thoria particle size was measured by a line intercept method perpendicular to the extrusion direction. Only particle sizes measuring 0.001 in. at X10,000 or larger could be extimated. Within limits of experimental error, particle size distribution appears to be unaffected by exposure, Fig. 2. To check structural stability further, a grain-growth evaluation was made. The number of grain-boundary intersections was counted at X500 on each of several traces normal to the extrusion direction for each condition. It can be seen from Table I that grain diameter appears unchanged by the 2000°F exposure. The slightly finer grain diameter after 200 hr may be attributed to variations in grain size from area to area in the original extrusion. From the present rather limited study of Ni-2 Th on, it appears that: 1) for time-temperature exposure up to 2000 hr at 2000°F (Larsen-Miller parameter = 57, homologous temperature = 0.8) thoria particles of the size studied are highly thermally stable; they do not significantly react, agglomerate, or diffuse; and

Jan 1, 1963

By Raymond L. Carpenter

The thermal conductivity, electrical resistivity, and Seebeck coefficient for nine compounds, based on the formula for enargite Cu3AsS3, were measured in a search for efficient materials to be used in thermoelectric generators or refrigerators. Results indicate that one of these compounds, Cu3SbSe4, has thermoelectric properties approaching those of bismuth telluride. An investigation of the effect of adding small quantities of tellurium to Cu3SbSe4 and Cu3SbS4 in order to improve their properties also was made. A figure of merit of 2.1 x 10-4 °C-1 was obtained for Cu3SbSe4 + 0.1 percent tellurium.

Jan 1, 1963

Jan 1, 1963

By J. A. Harrison

The physical composition of coal and the distribution of its physical constituents will partially determine the efficiency of the process chosen for coal preparation. Distribution and concentration of coal macerals will, to a degree, be controlled by preparation processes. A number of preparation processes have been evaluated to determine this interrelation. These evaluations will help provide information needed for the production of coal that meets definite petrographic composition specifications. etrographic composition and degree of coalifica-tion of coal can determine the choice of cleaning processes and equipment used in coal preparation. The purpose of this paper is to present data on studies of the preparation processes of breakage, sizing, cleaning, and blending and to show the effect coal's petrographic composition has on these processes. Herrin (No. 6) and Danville (No. 7) Coals from Illinois were used in these tests. Nomenclature used herein is that approved in the Glossary of the International Committee for Coal Petrology,' based primarily on the Stopes-Heerlen system of classification2 and used in coal petrography laboratories throughout the world. BREAKAGE TESTS Breakage tests of Illinois coals related to petrographic composition have been conducted at various times at the Illinois State Geological Survey. These tests have been classified under two headings -impact tests and compression tests. Impact tests, as the name implies, consisted of breaking the coal by a sharp, sudden force. Impact tests were further divided into fall tests and block tests. Compression tests consisted of applying a constant pressure on a piece of coal until the coal fractured.

Jan 1, 1963

By David Schlain

A small alumina reduction cell with a graphite crucible and boron nitride liner was developed by the Bureau of Mines as the initial phase of a study of the reactions which occur in the reduction of alumina by the Hall-Heroult process. Operating conditions in the cell such as temperature, time, current density, electrolyte composition, and electrode materials may be varied easily. Aluminum was produced in the cell at a current efficiency of about 75 percent and a cell voltage of 2.7 volts. Although the data are not wholly conclusive, the operation of the cell did not appear to be greatly affected by large changes in temperature, electrode spacing, current density, and alumina concentration in the electrolyte.

Jan 1, 1963

By F. C. Gibson

An electrical method for the continuous determination of propagation velocities in opaque, confined explosives, and propellants is described. A resistance element imbedded in the reactive material generates electrical signals that are displayed oscillographically and indicate the position and progress of a reactive zone associated with progress of a reactive zone associated with burning or detonation. The method is applicable to both solids and liquids.

Jan 1, 1963

By E. F. Bradley, R. I. Jaffee, H. R. Ogden, E. S. Bartlett, D. N. Williams

The mechanical properties of solid-solution-strengthened columbium alloys have been assessed as a function of alloying additions. Studies included the effects of tungsten, tantalum, molybdenum, and vanadium. Elevated temperature fabrication was required at alloying levels above about 15 pct W or 10 pct Mo. Tungsten, molybdenum, and vanadium additions increase tensile strength at room temperature and 2200°F, but tantalum additions exert little strengthening. Similarly, tungsten, molybdenum, and probably vanadium additions increase the ductile-to-brittle transition temperature, and tantalum additions decrease this parameter. The 2200°F stress-rupture strength is increased by tungsten and molybdenum additions; with 20 to 25 at. pct additions, 100-hr rupture strengths of 30,000 psi are obtainable. Small vanadium additions exhibit mild stress-rupture strengthening, and tantalum additions are innocuous. At 2500°F, tungsten additions retain stress-rutpure strengthening capability, but molybdenum additions are much less effective. Tantalum additions augment the stress-rupture strengthening of tungsten plus molybdenum additions at 2500°F. Of the refractory metals, columbium possesses specific potential for structural use in the temperature range from 2000" to about 2500°F. Desirable features of columbium are its good low-temperature ductility, ease of fabrication, oxidation mechanics (lack of a volatile oxide at moderate temperatures), good availability and reserves, and relatively low density. However, alloying is required to provide attractive strength at elevated temperatures. Published information concerning alloying be- havior of columbium relative to mechanical properties is sketchy, particularly in consideration for long-time applications at temperatures in excess of 2000°F. Only a few stress-rupture data at temperatures from 2000" to 2500°F have been reported;'-' these are too meager to allow rationalization of the effects of various alloying additions on creep or stress-rupture properties. Additional published data do, however, give some insight toward understanding of systematic alloying behavior for columbium relative to low-temperature strength4-' and ductility,' and elevated temperature tensile behavior.4,6 This paper is intended to augment previous knowledge, and to promote understanding of the alloying behavior of columbium for long-time structural service at elevated temperature. BASIC CONSIDERATIONS Solid-solution strengthening is recognized to be of prime importance in improving strength in columbium-base alloys. Other strengthening mechanisms may be (and are, in current alloys) used to augment solid-solution strengthening. As strengthening results primarily from lattice distortion, the strengthening effectiveness per atom depends upon atomic size mismatch between solvent and solute. Another factor in this regard is conformance to ideal solution behavior in the solid solution. Thus, for example, despite appreciable differences in the degree of mismatch between tungsten (5 pct), molybdenum (5 1/2 pct), and vanadium (7 1/2 pct) in solution in columbium, all are about equally effective in straining the columbium lattice at room temperature.'-' Similarly, tantalum additions do not strain the columbium lattice, and little strengthening is expected. Size effects being equal, maximum solution strengthening at high temperatures is anticipated to result from the addition of elements that increase the melting temperature of columbium. This expectation is based on an increase in the electronic bonding forces exhibited in the transition metal series as electronic structures approach those of the Group Vl metals. Of the metals that exhibit ex-

Jan 1, 1963

By D. T. Novick, M. B. Bever, B. Roessler

Ordered and disordered specimens of the alloy CusAu were cold worked and then annealed at 2880, 310°, and 340°C, together with disordered unworked specimens. me resistivity decreased during annealing mainly as a result of ordering; the resistivity measurements suggest that in cold-worked specimens the growth of antiphase domains is impeded. The strength properties increased during annealing at 288 "C; in cold-worked specimens this increase was lo a level above that for cold-worked specimens which had not been annealed. X-ray diffraction showed that after annealing for a few hours at 288ºC, the long-range order increased to a constant value; additional annealing at 288ºC resulted in the growth of antiphase domains in which the degree of order was constant. Changes in peak breadth and particle size confirmed that in cold-worked specimens the major effects of cold work were not eliminated during annealing at 288 "C, although a slight recovery process occurred. When a specimen of the alloy Cu3Au is heated to a temperature below the critical temperature (388ºC), long-range ordering tends to occur in a specimen containing less than the equilibrium amount of order characteristic of that temperature Ideally, a specimen of Cu3Au contains no long-range order if it has been quenched from above the critical temperature. Long-range order is reduced by cold work. If cold-worked specimens are heated, restoration processes such as recovery and recrystallization may occur,

Jan 1, 1963

By Albert W. Deurbrouck

This report describes the preparation characteristics of the significant, presently producing coalbeds in Mercer County, W. Va. Approximately 650,000 tons of coal was produced in Mercer County, W. Va., in 1960, of which over 630,000 tons was cleaned in four preparation plants. In 1960 the Pocahontas Nos. 3, 6, and 11 coalbeds supplied 99.5 percent of the total coal mined in the county. Because the number of working mines In this county was small, only six samples were collected; four of which were of metallurgical quality as mined. The remaining two samples could be upgraded by washing at suitable specific gravities. Many of the samples taken were of metallurgical quality as mined; however, the float-and-sink analysis on these coals has been included to point out their amenability to the production of premium quality, special purpose coals. In general the coals were low-volatile bituminous in rank with low ash and sulfur contents.

Jan 1, 1963

By J. F. Pierce, S. M. Enterline

Since January 1959 a zinc refiner of novel design has been in operation at Blackwell, Okla., producing 99.995+ zinc from the output of the Blackwell horizontal retort smelter. The refiner is a continuously operated, pyro-metallurgical unit with principal dimensions horizonhl permitting one floor operation. It is very ruggedly constructed. Furthermore it is not subjected to deterioration from high concentrations of iron in the feed metal because the boiling units are separate from the rectification columns and constructed with silicon carbide brick arches through which the heat is transferred radiantly to the zinc. A zinc refiner of novel design has been in operation since January 1959 at the Blackwell, Okla. plant of the Blackwell Zinc Co., Inc., a wholly owned subsidiary of American Metal Climax, Inc. Developed by the company's technical and operating staffs, the new refiner produces special high-grade zinc (nominally 99.995+ pct Zn) from the prime western1 slab output of the Blackwell horizontal retort smelter. The refiner is a continuously operated, pyromet-allurgical, high-capacity unit employing fractional distillation to separate zinc from its impurities, consisting principally of lead, cadmium, and iron. In prime western slab, these elements may vary in concentration from 0.005 to 1.6 pct. Table I shows the impurities usually encountered in the Blackwell prime western metal fed to the refiner together with their boiling points and vapor pressures at 907oC. The commercial pyrometallurgical smelting processes for extracting zinc from ore include distillation from retorts and a limited degree of refining can be accomplished by redistillation in similar retorts. To achieve special high-grade purity, an impractical number of batch redistillations would be required, however, with an accompanying loss of much metal. A continuously operated and integrated unit is required in which fractional vaporization and condensation can take place in a large number of stages. The first commercial continuously operated unit was developed by the New Jersey Zinc Co.4 In the separation of any two substances the degree of separation is limited if a mixture exists having a constant boiling point. The Zn-cd5 and Zn-pb6 systems contain no constant boiling points and hence these metals may be separated to any degree of purity. Basically, the pyrometallurgical refining of zinc involves three steps: a) iron, copper, and other metals having no appreciable vapor pressures at 907ºC concentrate in the bath when the impure zinc is boiled, b) lead, bismuth, antimony, and other metals having boiling points above but closer to that of zinc are selectively condensed from the vapor boiled from the bath, and c) cadmium and other metals having lower boiling points than zinc are fractionally distilled by reboiling and subsequent condensation of the zinc from the vapor. The boiling and condensation of zinc must be conducted in vessels constructed of materials which are refractory at the temperature involved (907 ºC) and it is highly desirable that they also be resistant to attack by the various metals. This requirement dictates construction from relatively small, simply shaped pieces which limits the pressures which may be employed to avoid leakage through the numerous joints. Stresses induced must be limited essentially to compressive ones and suitable provision must be made to permit thermal expansion of the components in order to minimize these stresses. Where heat is to be added for boiling or removed for condensation, refractory material through which the heat flows must have a high thermal conductivity. Silicon carbide is highly conductive but is subject to attack by iron and is expensive compared to other commonly employed refractories. A hard, dense aluminous fireclay is well suited to contain these metals where high thermal conductivity is not required. Zinc will penetrate the pores of fireclay brick but only to a limited depth in an exterior wall and has little effect other than an increase in weight and conductivity. The design objectives of the Amax refiner were: a) to achieve a long life by heavy, rugged construction and by employing silicon carbide refractories only where required for heat conductivity and not in contact with liquids of high iron concentrations, b) to simplify operation, manning and control by essentially horizontal construction, and c) to obtain high capacity in a single unit. DESCRIPTION Flow of metal through the Amax refiner is shown diagrammatically in Fig. 1 and schematically in Fig. 2.

Jan 1, 1963

By R. M. Hudson

A study has been made of the decarburization of low-carbon sheet steels at temperatures from 1100" to 1475°F in mixtures containing hydrogen, nitrogen, water vapor, and in some instances carbon monoxide. Decarburization occurs principally by the reaction C (in steel) + H20 = CO + H2 and follows a first-order rate law. The decarburization rate appreciably increases with an increase in temperature up to about 1325°F, but the increase in rate is small with fur- Use of a dry hydrogen atmosphere results in a relatively slow decarburization of steel and use of a wet hydrogen atmosphere results in relatively rapid decarburization. It is now generally recognized' that the reaction C (in steel) + H2O = H2 + CO [l] accounts for most of the decarburization that occurs in wet hydrogen-containing atmospheres. The present article is concerned with the decarburization of low-carbon sheet steel in H2-N2 atmospheres ther increase in temperature. The limiting rate of decarburization can be predicted from a knowledge of the solid solubility and diffusivity of carbon and this rate is approached as the water-vapor content of an atmosphere is increased. Hydrogen contents above about 8 pct are beneficial only in that they permit higher levels of water vapor to be used without oxidation of the steel. A buildup of CO in the atmosphere lowers the rate of decarburization. containing various amounts of water vapor and carbon monoxide. The effectiveness of these atmospheres and the influence of temperature on decarburization rate will be considered. EXPERIMENTAL WORK The chemical compositions of the three steels used in decarburization-rate studies are listed in Table I. Steel A was a commercially hot-rolled rimmed steel that was cold-reduced at the Laboratory to furnish specimens 0.025, 0.041, and 0.059 in. thick. Most of the experiments in which this steel was used were made on the 0.041-in.-thick material. Steel B and Steel C were cut from 0.010-in.-thick commercially cold-reduced coils that were

Jan 1, 1963

By Robert E. Johnson

1962 was the second year of recovery from the mild 1960-61 recession. The year-to-year gain in constant dollar gross national product, our most comprehensive measure of the country's economic performance, was 6.0 percent (from $447.7 billion in 1961 to $474.8 billion in 1962). The unemployment rate declined from 6.7 percent to 5.6 percent. Although it was a good year, there were still unused resources of labor and capital which implied that the economy was operating below its potential. The year-to-year change in the Federal Reserve Board (FRB) index of industrial production of 7.6 percent masked the fact that more than one-third of the growth took place within 196L The monthly index rose only 4.8 percent during 1962, from 114.3 in January to 117.8 in September. The fact that the economy as shown by the industrial index, rose rapidly in the first half of the year only to remain on a plateau of 119-120 during the second half, led some people to fear an imminent downward turn. This did not occur. Neither production nor consumption of mineral fuels advanced as fast as the total economy. But consumption showed more gain than production, 5 percent compared with somewhat less than 4 percent. Production of both crude oil and natural gas reached new highs while bituminous coal production was the highest in 5 years.

Jan 1, 1963

By H. R. Ogden, A. G. Imgram, D. N. Williams

The effects of composition on the mechanical properties and aging characteristics of several alloys in the Ti-V-Cr system, with and without aluminum modifications, were evaluated. Increasing the chromium, vandium, or aluminum content increased the strength of quenched structures with chromium being the most effective strengthener. Appreciable aging response was obtained with low chromium alloys, but high chromium alloys age softened rather than. hardened. High vanadium contents had a similar effect. Aluminum additions shifted the aging behavior toward that observed in lower chromium alloys, enabling high chromium alloys to be age hardened. DURING the course of titanium alloy development many a and a-ß alloys have been evolved to commercial status. However, only one all-ß alloy has achieved this same stature. This is the Ti-13V-11Cr-3Al alloy. It is characterized by a very sluggish ß-phase decomposition reaction such that very slow cooling rates can retain the 0 phase at room temperature. In addition, very high strength levels can be obtained by long-time aging treatments. Combinations of cold or warm working followed by aging produce even further improvements in strength. This paper describes the results of a research program in which the effects of composition on the mechanical properties and aging characteristics of several alloys in the Ti-V-Cr system, with and without aluminum modifications, were evaluated. EXPERIMENTAL PROCEDURES Electrolytically refined, high-purity titanium was used as the alloy base for these studies. Iodide chromium, electrolytically refined vanadium granules, and high-purity aluminum sheet were used as alloying additions. The compositions of interest were melted as 250-g ingots in a direct current arc melting furnace under a flowing atmosphere of argon. The ingots were hot forged to 3/4-in.-diam bars, vacuum annealed for 6 hr at 1800°F to reduce residual hydrogen content, and then hot swaged to 1/4-in.-diam rods. Fabrication history, and interstitial analyses after fabrication are given in Table I. All specimens to be heat treated were sealed in Vycor capsules under a partial pressure of argon. Samples used to define the ß transus were quenched from temperatures ranging from 1350° to 1100°F after holding at temperature for 15 min. Samples for aging studies were quenched from above the ß transus temperature and then aged for up to 64 hr at 750°F and for 100 hr at 850°, 900°, and 950°F. The effects of straining prior to aging were also investigated. The results of these studies were used to select the heat treatments for the tensile specimen blanks. Heat treatments of the tensile specimens are described in Table 11. Alloys were aged after solution heat treatment or after solution heat treatment and cold swaging to 50 pct reduction in area. Standard 0.125-in.-diam tensile specimens were machined from the heat-treated blanks. All tensile tests were performed in a Baldwin-Southwark uni-

Jan 1, 1963

By E. A. Steigerwald

E. A. Steigerwald (Thompson Ramo Wooldridge, Inc.1— he authors' results clearly indicate that cracking can be produced by the hydrogen pressure developed during a charging operation. This type of cracking or blistering has also been observed in polycrystalline materials24"28 when the charging conditions are sufficiently severe and is often referred to as irreversible embrittlement since it cannot be removed by a baking treatment. There are additional data, however, which must be considered before a pressure theory can be generally employed to account for all failures which occur as a result of hydrogen. In many cases, hydrogen embrittlement in a tensile test or in delayed failures under static loads is a reversible phenomena which cannot be simply explained on the basis of preexisting cracks generated by the charging operation. It is this aspect of the problem which has prompted many investigators to seek mechanisms other than hydrogen pressure to explain their results.24'n728 Fig. 15 indicates an example where, under specific experimental circumstances, hydrogen embrittlement can occur at liquid nitrogen temperatures. In this case, which has been previously decribed,'' specimens were charged with varying quantities of hydrogen, immediately quenched, and tested in liquid nitrogen (-320°F). A companion set of identical specimens were charged, aged at 300°F to remove the hydrogen, and also tested at -320°F. When the current density was greater than lo-' amp per sq in., embrittlekent occurred in both sets of specimens, indicating that cracking had occurred during charging and the embrittlement, as in the case of Fe-Si single crystals, was irreversible. At current densities between approximately 103 and lo-' amp per sq in, the embrittlement was present only for those specimens which contained hydrogen during the testing sequence. The embrittlement was therefore reversible with respect to the aging and charging operations. Since extensive hydrogen movement would not be expected at -320°F, it is difficult to reconcile these data with a mechanism which requires pressure and pressure dependent growth of preexisting cracks. There are other features of hydrogen embrittlement such as the reversibility of the incubation time for delayed failure with respect to applied stressg0 and the influence of prestraining31 which are also difficult to explain using a pressure model. Any general mechanism of hydrogen embrittlement will have to consider the reversible aspects of the embrittlement data as well as the irreversible portion which has been clearly presented for the Fe-Si crystals and which is consistent with a pressure model. A. S. Tetelman and W. D. Robertson (authors' reply)—he authors agree with Dr. Steigerwald that a general mechanism of hydrogen embrittlement must be applicable in all cases where embrittlement occurs. Dr. Steigerwald's experiments were performed on an iron alloy which has an extremely complex microstructure, and therefore does not lend itself to the direct and detailed observations that can be made in Fe-Si. The change in the characteristics of cracks as a consequence of annealing at 300°F is not really known in detail but it is probable that stress-relaxation (blunting) occurs, dislocations produced near the crack tips will be pinned by carbon atoms, and hydrogen will be lost to the atmosphere. Any, or all of these effects of annealing will alter the ease with which a crack subsequently propagates under applied stress. A quantitative treatment of the problem must take these effects into account. Since diffusional processes are presumably eliminated at -320°F, the general mechanism proposed by Dr. Steigerwald's colleagues cannot be operative at this temperature. A detailed discussion of the general' inapplicability of this mechanism has been presented elsewhere. However, the data presented by Dr. Steigerwald in his discussion can be explained in terms of a pressure model. Crack propagation under internal pressure P and applied stress occurs when where is the total energy expended in creating new surface area and by plastic work at the crack tip. The total crack length increases with increasing current density, since we have shown that it systematically increases with hydrogen concentration and Dr. Steigerwald has shown that hydrogen concentration increases with current density. For large L (high current density) Eq. [I] can be satisfied even if P = 0 and the embrittlement process does not require the presence of hydrogen. Specimens charged at a lower current density will con-

Jan 1, 1963

By H. M. Thorne

Industrial shale-oil operations in North America and Europe predated the Drake discovery, but, since then, most have succumbed to competition from petroleum. However, the existence of enormous oil-shale resources in the Green River formation of Colorado, Utah and Wyoming [estimated at over a trillion bbl of shale oil in place] and the advancement of United States oil- shale technology by research and development programs of government and industry during the past 15 years point to a natural partnership of petroleum and oil shale to meet the accelerating energy demands of the future. The utilization of oil shale is not a question of limited petroleum supplies, but one of economics. Two factors are expected to improve the economic outlook for industrial shale oil production -- a rise in petroleum replacement cost and further advances in oil-shale technology.

Jan 1, 1963

By J. M. Toguri, H. Flood

The application of the mass action law to the thermodynamic treatment of metal-slag equilibria is discussed. The consideration of the reactions essentially as ionic exchange equilibria is shown to be both an advantage and an aid for the elucidation of the theoretical treatment. This is illustrated by several examples. In general two different methods of application of the mass action law to metal-slag equilibria have been used by different groups of investigators. These could be called the oxide reaction and the ionic reaction approach respectively. At the recent discussion in the metallurgical section of the I.U.P.A.C. Congress in Montreal, 1961,' divergent opinions prevailed regarding the most rational way of applying the mass action law to metal-slag equilibria. This question is of fundamental importance in the treatment and understanding of theoretical chemical metallurgy. Consequently, the following is an attempt to contribute towards its clarification. As an example, the distribution of iron and manganese between molten iron and slag will be considered. I) THE OXIDE EXCHANGE REACTION APPROACH The equilibrium between iron and manganese between molten iron and slag is frequently formulated as an oxide metal exchange reaction as follows:

Jan 1, 1963

By D. L. King, C. D. Rubert, R. W. Christy, B. A. Schepman

R. W. Christy (Manager of Sales, Sanitary Engineering Equipment, Link-Belt Co.) and C.D. Rubert (Barrett, Haentjens & Co.) — Messrs. King and Schepman have presented an excellent paper which outlines the general practice in the design of thickener mechanisms. Lifting devices, controls, special applications and underflow pumping arrangements have been reviewed in detail. Pumping arrangements were illustrated which eliminate the need for an expensive tunnel beneath the thickener floor. Most of those illustrated have the common feature of a relatively long underflow suction line extending from the hopper floor to the pump located on the bridge at the periphery of the tank. The authors limit these arrangements to comparatively dilute or thin slurrys. It is implied that dense and coarse concentrates, which are difficult to pump, cannot be handled unless a tunnel is constructed. Fig. 1 shows an underflow pump arrangement which negates the need for a tunnel but which permits the operator to convey a heavy dense slurry. The pump is mounted directly on the fixed hoist platform and the impeller is located at the base of the steel center column. Priming water is not needed. The column

Jan 1, 1963

By A. English, M. J. Greaves

This paper is a discussion of pelletizing systems developed over the last 15 to 20 years for the agglomeration of fine iron ore concentrates. Five different pelletizing systems are now in commercial use in the U.S., and for the purposes of comparison, estimated operating costs and capital costs for the construction of four of them are included. Capacities of existing commercial plants are examined, together with the anticipated capabilities of plants presently being built or projected. In just 21 years, the art of pelletizing iron ore concentrates has reached maturity with mastery of the separation of finely divided concentrates from low-grade iron ores and their agglomeration into pellets containing about 65% iron. This accomplishment has firmly established an improved feed for the blast furnace, with resulting benefits in faster reduction of burdens and greater economy of operation. The present production capacity of pelletizing facilities in the U.S. is about 20 million tons annually, and it is expected to double by 1970. The rapid expansion of pelletizing in the U. S. has been closely observed in European countries, notably in Sweden and Germany, where pioneer agglomerating techniques were developed early in this century. PELLETIZING PLANTS AND PROCESSES Twelve commercial pelletizing plants are presently in operation in the U. S. and Canada. An equal number are in various stages of engineering and construction, and many others are being considered. The pelletizing systems currently employed include shaft furnaces, horizontal grates using three different airflow arrangements, and grate kilns. The capacity of pelletizing operations in North America is shown in Table I. All of these plants are integrated with the mine, the ore-crushing facilities and the concentrating plant and are equipped with storage and loading-out facilities for the product. Normally, a pelletizing plant is composed of a shuttle conveyor above the receiving bins; balling equipment; a heat-hardening system including the necessary auxiliaries such as furnaces, burners and controls, ducts, fans, meters and instrumentation; fines recovery equipment; and product handling equipment. Also included are the necessary auxiliaries and utilities such as boilers or power plant; oil unloading and storage facilities; coal unloading storage, grinding and distribution facilities; and bentonite or other additive storage and distribution equipment. Shaft Furnaces: Vertical shaft furnaces used in this country are limited to the treatment of natural magnetite concentrates containing minor quantities of residual fluxing elements. Fig. 1 shows a perspective view of the shaft furnace with balling, feeding and pellet-handling equipment. An elevation of a shaft furnace is shown in Fig. 2. A commercial shaft furnace unit is about 45 ft in height with a 6 x 14-ft rectangular cross section and has a nominal production rate of approximately 50 gross tons of pellets per hour. The upper portion of the furnace shaft is constructed of fire brick as protection from the high process temperatures involved. The lower portion of the shaft is lined with abrasion-resistant brick to withstand erosion from the fired pellets. Rectangular-shaped, refractory-lined and insulated combustion chambers are situated on each side of the shaft furnace. Oil or gas is burned to produce high temperature gases which are forced into the furnace through ports located near the top of the combustion chambers. The shaft furnaces operate at a pressure of approximately 6 psi. Pellets are fed into the top of the furnace by a pantographic feeder designed to produce the desired pellet stockline. The furnace is kept filled at all times and pellets are fed and discharged from the furnace at the same rate. In early development, 10 to 12 lb of solid fuel was incorporated in the pellets. However, the main source of process heat is now derived from the combustion chamber gases. In some instances no solid fuel is used. The pellet movement in the shaft furnace is counter-current to the flow of gases. Ambient air is introduced through louvers at the lower end of the furnace, at about 6 psi, cooling the fired pellets and supplementing the heat of the high temperature gases from the combustion chamber ports. The zone of maximum temperature, located above the ports of the combus-

Jan 1, 1963