Search Documents

By J. W. Downey, J. B. Darby, L. J. Norton

THE only previous investigation of the phase equilibria in the Ta-Pd system was reported by Greenfield and Beck.1 Their work (actually a portion of a much broader survey) was limited to the composition range 50 to 75 at. pct Ta and to a single temperature, 1000°C. The results indicated that no intermediate phases were present at this temperature. They pointed out that this was an unexpected result in view of the fact that niobium, which belongs to the same group in the periodic table as tantalum and has essentially the same atomic size, forms a o phase with palladium.' Also, tantalum in combination with rhodium,' iridium,' or platinum' stabilizes the s phase. By analogy, the Ta-Pd system would also be expected to contain a s phase. The present investigation was therefore undertaken to explore more fully the phase relationships in this system. Alloys were prepared by arc melting on a water-cooled copper hearth in an argon-helium atmosphere. The purity of the starting materials was greater than 99.9 pct. The weight losses on melting were less than 1 pct and therefore the alloys were not analyzed chemically. Specimens were wrapped in molybdenum foil, encapsulated in quartz capsules under a vacuum of at least 1 x 10-5 mm of Hg, annealed as indicated in Table I, and water quenched. Optical and X-ray metallography were used for identifying the phases present in the annealed and quenched alloys. The alloys were resistant to attack by several acids; however, a sodium cyanide electroetch and an immersion etch containing 1 part HF, 1 part HNO3, 2 parts H2SO4, and 5 parts H2O by volume were found satisfactory. The X-ray diffraction patterns were taken with a Straumanis-type Debye-Scherrer camera and filtered copper or chromium radiation. A summary of the phases found in this investigation is presented in Table I. No attempt was made to determine the composition limits of the various phases. The present results indicate that this system consists of two terminal solid solutions separated by at least four intermediate phases at the approximate compositions Ta3Pd, -TaPd, TaPd,, and TaPd3. The Ta-rich solid solution, containing less than 10 at. pct Pd at 1150°C, is in equilibrium with a o phase which is stable in the vicinity of 25 at. pct Pd. The latter phase is also in equilibrium with a bct phase at the equiatomic composition. At high temperatures it appears that the Pd-rich solid solution extends to at least 66.6 at. pct Pd and is in equilibrium with the bct phase. When annealed at 900°C, a sample containing 66.6 at. pct Pd transformed to an unidentified phase designated as X. An X-ray diffraction pattern of this phase contained sharp low-angle lines while the high-angle lines were characteristically diffuse. The observed d-spacings and relative intensities for lines in the low-angle region are presented in Table 11. In the vicinity of 70 at. pct Pd an intermediate phase having the TiA13-type structure is formed. It is stable to at least 1100°C, and presumably dissolves congruently into the ter-

Jan 1, 1963

Most mines in the Bundamba, North Ipswich, and Rosewood districts of the West Moreton coalfield of south eastern Queensland have installed washing plants during the last five years. Many problems were encountered in their installation, including the small size of washing plant required in many cases, the economical minimum ash content under present and future market requirements, production from a one-product washbox of large and small coal of quality to satisfy both markets, measures to avoid adding unnecessary moisture to the washed slack coals, and excessive middlings in some coals or soft clay in others.INTRODUCTIONIt was fortunate for Brisbane, which was to become the capital of a new State, Queensland, in 1859, and grow into a city of over half a million people by the time of its centenary, that coal was found in abundance almost on its doorstep near Ipswich, the first mine being opened at Redbank in 1843. This was followed by the opening of many more mines in that district and, some 40 years later, in the nearby Rosewood district where high-volatile gas coal was produced (Fig. 1). These discoveries ensured a supply of reasonably priced coal (currently about 85/- per ton delivered) in Brisbane, but the quality is inferior to that of other coals mined in Queensland beyond economic range of Brisbane.Various factors led to an increase in the average ash content of the West Moreton coals during and after the war. Between 1940 and 1952 the gasworks coals rose in average ash from 13 8 per cent to 23·9 per cent and the powerhouse coals from 17·1 per cent to 27·1 per cent. This drift was arrested by the installation of 28 screening and picking plants from 1952 onward, but it became obvious that mechanical cleaning of the coals was essential due to the competitive market for coal and the worsening quality of reserves.

Jan 1, 1963

By A. H. Daane, W. J. Wunderlin, B. J. Beaudry

The solid solubility of holmium in copper, silver, and gold, determined using metallographic techniques, was found to be a maximum of 0.06, 2.4, and 3.2 wt pct, respectively, nt the eutectic temperatures. The temperatures of these eutectic horizontals, determined by differential thermal analysis, were found to be 868", 787", and 778"C, respectively. The first compound on the silver-rich side of the Ag-Ho system was found to be A&Ho2. In a study by Gold et al.,' on the effect of small amounts of soluble impurities on the electrical resistance and thermoelectrical properties of copper, traces of iron were shown to have drastic effects on the thermoelectric power due to the magnetic scattering of the conduction electrons. Since little is known about the state of the iron ion when dissolved in copper, Gold had hoped to repeat these experiments using certain rare earths as the magnetic scattering centers; because of the tightly bound 4f electrons it is not expected that their spectroscopic state would be affected by alloying. In such an experiment the sole role of the trace rare-earth impurity would be to magnetically scatter the copper conduction electrons without producing appreciable distortions in the otherwise pure copper matrix. Since holmium was chosen for such a study because of its high magnetic moment, it was necessary to establish precisely its solid solubility in copper. The study was extended to include the solvents silver and gold, so that an evaluation of the data using classical solubility parameters could be made. No previously reported work on the systems of holmium with copper, silver, or gold was found in the literature. Information on the solubility of other rare earths in these three metals is also very meager. The solubility limit of yttrium in copper was reported as less than 1 wt pct2 and the solubility of praseodymium in gold as 0.35 wt pct,3 while no references were found on solubility studies of rare earths in silver. EXPERIMENTAL Materials. The materials used in this investigation were distilled holmium prepared in this Laboratory, OFHC* copper, electrorefined silver (99.9 *OFHC = oxygen-free high conductivity. pct), and gold with the analyses given in Table I. Sample Preparation. Samples weighing 1 to 2 g were prepared by arc-melting the components together on a water-cooled copper plate under purified argon atmosphere. The samples, turned and remelted at least five times to ensure homogeneity, showed weight changes of less than 0.1 wt pct after melting. Samples containing less than 0.7 wt pct Ho were prepared by diluting 1 to 2 wt pct Ho alloys with the pure solvent, while samples with concentrations greater than 0.7 wt pct Ho were prepared directly from the metals. The samples were wrapped in tantalum foil, sealed in outgassed Vycor tubing under helium, annealed at the desired temperature for at least 24 hr, and then quenched by shattering the Vycor tube in cold water. Metallographic Methods. Standard mechanical polishing methods were used in preparing the silver and gold alloys for examination, while the copper alloys were electropolished using a 40 pct solution

Jan 1, 1963

By C. W. Allen, B. D. Cullity

The proportional limit of iron crystals in torsion is governed by the resolved shear stress in the most highly stressed slip systems, averaged around the specimen circumference, and does not obey a critical resolved shear stress law. Crystals of most orientations exhibit a stage of easy plastic deformation, akin to easy glide in tensile or shear specimens. Transient deformation, similar to that which occurs in single crystals of other materials, is also observed. THE torsional deformation of single crystals of magnesium (hcp) and aluminum (fcc) has been described recently by Choi et al.,&apos; especially with respect to the criterion for the orientation dependence of the onset of plastic flow in these materials. The purpose of this paper is to present results of torsion tests of iron single crystals and thus to extend this yield criterion to a bcc metal. In addition to considering the variation of proportional limit with crystal orientation, this paper also briefly treats work hardening, transient deformation, and the mechanism of plastic flow in iron. The effects of the method of surface polishing and the chemical purity of the iron have been investigated. STRESS DISTRIBUTION It is convenient to express the stress at any point of a cylindrical crystal stressed in torsion in terms of t0, which is the shear stress acting at the surface on a plane normal to the axis of the cylinder and in a direction tangential to the cylinder. This stress is given by To = 2T/pr3 [1] where T is the applied torque and r the specimen radius. The shear stress t, resolved in any chosen slip system is given in terms of 7, by1 Ts/TO = sin 0, cos d sin (0, -) + cos , sin d sin d - ) [2] where 0 and d are the angles between the specimen axis and the slip plane normal and slip direction, respectively; h is the angular circumferential position on the specimen at which t, is being determined, measured from an arbitrary reference plane which includes the axis;o and d are the angular coordinates of the projections of the slip plane normal and slip direction on a transverse section with respect to this same reference plane. Slip in iron occurs in a <1ll> direction on the {ll0}, (1121, and (123) planes, which together comprise 48 slip systems. A complete evaluation of the stress distribution in an iron crystal stressed in torsion would therefore require a calculation of Ts/T0 as a function of for 48 different slip systems. Fortunately Gough,&apos;who studied the behavior of iron crystals in alternating torsion, was able to simplify this problem considerably. He showed that it was sufficient to consider a kind of average slip plane for each slip direction, namely the mathematical plane of maximum resolved shear stress containing the slip direction considered. This simplifying approximation is possible because, for each slip direction, the active slip plane or planes lie very near this mathematical plane of maximum shear stress. Vogel and rick&apos; have critically reviewed the early work of Taylor and Elam,13 Taylor,14 and Fahrenhorst and schmid8 from which the identification of the above crystallographic planes as slip planes in the bcc lattice largely stems. While their criticism is clearly justified, their own results do little to clarify the issue. The role of cross slip (screw dislocations changing glide planes) is evidently so important in this case, as Read3 has suggested, that methods for deducing slip systems from observations of gross slip traces are inadequate, such traces commonly arising from complex dislocation motion. Thus the treatment given here involving the plane of maximum resolved shear stress seems a logical simplification especially in view of Gough&apos;s2 study of a iron. There is, however, an assumption built into the subsequent treatment the comparative validity of which is difficult to assess, namely, that slip in all slip systems in iron may be characterized by a common critical resolved shear stress. The shear stress 7, resolved in a slip direction defined by d andd, and on the plane of maximum shear stress containing this direction, is found by first maximizing 7s/70 with respect to either Oo or 4,. The slip plane coordinates are then eliminated by using the relation between 0, ,o and d, d, namely,

Jan 1, 1963

By Richard F. Hewlett

The mining industry utilizes a vast store of knowledge, wisdom, and engineering talent in designing mining systems. However, the complexity of the required systems and the presence of numerous variables frequently necessitates raking important decisions without having adequate accurately detailed information. That many of the decisions made in the past were nearly correct, in the long run, is substantiated by the number of successful mining enterprises that exist in the world today. Subsequent to 1940, the disciplines of operations research and systems engineering were developed. The disciplines have produced methods of providing better information to persons responsible for making decisions.

Jan 1, 1963

By C. L. Coldren

Recently there has been much discussion of the use of pipelines for the long-distance transportation of solids. Many have come to recognize the economies inherent in pipeline transportation. The widespread movement of oil and gas at astonishingly low costs - a gallon of oil moves from Montana to New York for less than that for the delivery of a postcard - has spurred others to sturdy this mode of transportation. Most interested people are aware of the inherent advantages of pipelines - continuity and reliability of operations - low manpower requirements per ton mile - moderate capital costs per ton mile - low maintenance costs per ton mile - low operating costs per ton mile.

Jan 1, 1963

By Robert Stefanko

The importance of underground stress instrumentation cannot be minimized. It was Lord Kelvin who said that unless you can assign a number to a quantity,, you know very little about it. Most engineers will agree although this kind of statement is resented by our friends in non-technical fields. Mining is undergoing a revolution from art to science. But how can mining methods be optimized if there is no way of measuring the effectiveness of a given mining method? Do we know how effective a&apos; support is unless we can determine its reaction to the mine structure? How do we assess the need for modifications to existing systems and supports, and how do we measure the effectiveness of such changes? Cut and try techniques are too wasteful of time and energy, and rarely provide solutions to a given problem. The purpose of underground stress instrumentation is to provide answers to some of the above questions -- answers that cannot be obtained otherwise This does not mean that laboratory studies are not valuable -on the contrary. Laboratory and underground studies supplement one another. Rock mechanics had its conception with the study of stresses in homogeneous, isotropic, and elastic models subjected to various force systems. These analyses were valuable inasmuch as they pinpointed possible sources of trouble due to stress concentrations. If the results observed underground did not always agree with the experimental analysis, it was not an indictment of the latter. More probably, the discrepancy could be attributed to the lack of similitude between model and prototype. The more nearly one can simulate underground conditions in a model, the more apt one is to produce results which correlate well-with underground observations. It is impossible to completely simulate underground conditions because all of the significant design parameters have not been recognized and evaluated. What better way can one evaluate these parameters than by underground stress instrumentation?

Jan 1, 1963

By H. E. McCoy, C. J. McHargue

Single crystals of columbium containing various levels of oxygen, nitrogen, carbon, or hydrogen were deformed by slaw compression and impact loading at -196°C. For the slow deformation rates. 1500 to 1900ppm oxygen, 500 pprn nitrogen, or 150 to 200 ppm carbon completely suppressed mechanical twinning. Hydrogen in concentrations to 1000 ppm had no apparent effect on ease of twinning. Impact loading caused twins to form at all levels of contamination studied, and cleavage mucking on (100) planes occurred in specimens having higher interstitial contents. It is well established that, under some conditions, the bcc metals vanadium, columbium, tantalum, chromium, molybdenum, tungsten, and iron deform by formation of mechanical twins. In general it has been accepted that high strain rates, low temperatures, and large grain sizes are conducive to this kind of deformation.&apos; Since interstitial impurity atoms have a relatively large effect on slip in bcc metals, one might sus- pect a similar effect on twinning. This could occur directly by the interstitials affecting the nucleation or growth of the twins or indirectly from their effect on slip. It has often been argued that the large increase in yield stress caused by interstitial elements enables the effective stress to exceed that necessary to cause twinning. The twinning stress has always been thought to be higher than the stress necessary to cause slip in pure metals.2 simonsens and Tipper and Hall4 found profuse twinning in very pure a iron even at room temperature, whereas Low and Fueste15 and Churchman and tottrell&apos; observed twins in a iron containing carbon but none in highly decarburized specimens. McHargue7 reported mechanical twins to form readily in vanadium which contained 390 ppm interstitigs, while Clough and Pavlovic8 found twins only in the one or two grains adjacent to the fracture surface in vanadium which contained 1500 to 1700 ppm interstitials. In columbium, McHargue9 found high-purity single crystals to twin easily whereas Churchman,10 Adams, Roberts, and mallman,11 and Johnson12 studied less pure material and found far fewer twins. Although the results of Leadbetter and Argent13 showed oxygen to inhibit twinning, a study by sheely14 indicated the opposite to be true. Chromium exhibits this mode of deformation15,16 but there are no data regarding impurity effects. Lawley, Van den Sype, and Maddin17 observed twins in very pure molybdenum single crystals deformed at 77°K but none in less pure crystals. The work by Cahn18 and

Jan 1, 1963

By J. M. Uys, T. B. King

The solubility of water in silicate melts of various compositions was measured. The basicity of the silicate did not appreciably affect the water solu-bulity at low-base content (acid compositions). Near the orthosilicate composition the solubility increased with basicity for silicates in which the cation displayed a weak ion-oxygen attraction and apparently decreased for those in which the cation showed a strong ion-oxygen attraction; metasilicates of the former class dissolved more water than those of the latter. Temperature had little effect on water solubility. The experimental results are interpreted on the basis of two modes of solution, the contribution of one decreasing, and that of the other increas -ing, with increased melt basicity. In the former, solution occurs through interaction with doubly-bonded oxygen atoms and in the latter, through interaction with singly-bonded oxygen atoms, or, in very basic melts, through reaction with free oxygen ions. THE hydrogen content of a steel melt is in a large measure determined by water dissolved in the slag. In some glasses water may be a major cause of "seeds". Water vapor in the furnace atmosphere is the primary source in both instances. A knowledge of the mechanism of water solution in silicate melts should help in assessment of practical methods for its control in steelmaking and glass refining. Walsh et a1.l measured the water content, expressed as hydrogen, of 40 pct lime-20 pct alumina-40 pct silica and 62 pct manganese oxide-38 pct silica melts as a function of the steam partial pressure, in equilibrium with the melt. Tomlinson 2 and, also, Russell3 investigated this relationship for a molten 30 pct soda-70 pct silica glass. In all three investigations, the solubility of water was found to be proportional to the square root of the partial pressure of steam. Moulson and Roberts 4 confirmed this relationship for a silica glass. On the basis of the square root relationship, Tomlinson2 and Russell3 interpreted the solution reaction as "network-breaking", similar to that expected on the addition of metal oxides to silica. Walsh et al.&apos; postulated two possible modes of solution, one the mechanism suggested by Tomlinson and Russell and the other the reaction of the water molecule with an oxygen ion to form hydroxyl ions. These two modes of solution suggest opposite effects of melt basicity on water solubility. However, little appears to be known about the effect of melt basicity on water solubility. Walsh et a1.l found, in the lime-silica system, that the water content increased slightly with increased basicity. As these authors pointed out, this does not appear to be in accord with their further observation that slags containing little or no silica dissolve very little water. Kurkjian and Russell5 measured the effect of basicity on water solubility in alkali silicates in the composition range 15 to 45 mole pct alkali oxide. They found a minimum in the water content at about 25 mole pct alkali. This was interpreted on the basis of two concurrent solution reacZions; one in which solubility was proportional to the activity of doubly-bonded oxygen and, in the other, proportional to the activity of singly-bonded oxygen. The present work was aimed at establishing the effect of basicity on water solubility in silicate melts over as wide a range of compositions as practical. APPARATUS AND EXPERIMENTAL PROCEDURE The silicate melt was equilibrated with a "carrier-gas" of accurately known water content, quenched, and analyzed for water by a vacuum fusion technique. Some pertinent details of the equilibration procedure, analysis technique, preparation, and handling of the silicates are given below. Gas-Silicate Equilibration. The apparatus used to equilibrate the melt with the gas mixture was similar to that used by Walsh et al.&apos; but with some important modifications.6 Purification trains were provided for nitrogen and hydrogen; whenever air or oxygen was used as carrier gas the nitrogen purifiCation train was used with the copper furnace at room temperature. Gas flow rates were measured with capillary flow meters; bleeders filled with a mixture of dibromo and tribromo ethyl benzene (density about 2 g per cc) were used for convenience in controlling flow rates.

Jan 1, 1963

By M. J. Ackerman, C. R. Waine, W. M. Merritts, L. P. Mokwa

Tests were conducted in the Pocahontas No. 4 coalbed in southern West Virginia to determine if successful degasification techniques, developed during an earlier study in the Pittsburgh coalbed, would be effective in removing methane from those usually more gaseous coals. Specially designed long-hole drilling equipment and Bureau of Mines continuous recording devices were used to measure the quantity and methane content of the ventilating air during the investigation. Infusions were made with water at normal waterline pressures ranging from 200 to 220 psi or at pump pressures ranging from 400 to 650 psi. Results of the tests showed that methane emissions from free-flow bleeder holes were as much as 131 cfm. Infusions of some of the holes increased the methane emission from other holes and from the exposed coal surfaces near the working areas as much as 1,540 cfm. The methane content in the main return-air currents after infusion was reduced more than 86 percent of the amount recorded before tests were made.

Jan 1, 1963

By H S. Ellis

Flow studies have been conducted on nickel-water suspensions in a 1in.-diam., 42-ft.-long transparent lab-oratory pipeline at concentrations of up to 25 per cent, by volume, and slurry velocities of up to 15 ft/sec. The average size of the nickel powder was approximately 150 mesh (106J.L). Three flow regime were noted. At the highest velocities, i.e., above 10 ft/;sec., where the concentration distribution through the vertical diameter was most uniform, pressure gradients could be correlated with the Durand-Condolios equation (7,8). An intermediate region, i.e., from 7 ft/sec. to10 ft/sec., could be distinguished, the lower velocity limit being that at which nickel particles began to deposit. This region was also marked by decreasing pressure gradients, for a given concentration, as the velocity was reduced. The upper velocity limit in this region was also uniquely defined in that the friction factor for any nickel concentration was the same as that for water. In the third regime, below about 7 ft/sec

Jan 1, 1963

By John Henderson

FOR some time now the most commonly accepted description of liquid silicate structure has been the "discrete ion" theory, proposed originally by Bockris and owe.&apos; This theory is that when certain metal oxides and silica are melted together, the continuous three dimensional silica lattice is broken down into large anionic groups, such as sheets, chains, and rings, to form a liquid containing these complex anions and simple cations. Each composition is characterized by "an equilibrium mixture of two or more of the discrete ions",&apos; and increasing metal oxide content causes a decrease in ion size. The implication is, and this implication has received tacit approval from subsequent workers, that these anions are rigid structures and that once formed they are quite stable. The discrete ion theory has been found to fit the results of the great majority of structural studies, but in a few areas it is not entirely satisfactory. For example it does not explain clearly the effect of temperature on melt structure,3 nor does it allow for free oxygen ions over wide composition ranges, the occurrence of which has been postulated to explain sulfur4 and water5 solubility in liquid silicates. In lime-silica-alumina melts the discrete ion theory is even less satisfactory, and in particular the apparent difference in the mechanism of transport of calcium in electrical conduction8 and self-diffusion,&apos; and the mechanism of the self-diffusion of oxygen8 are very difficult to explain on this basis. By looking at melt structure in a slightly different way, however, a model emerges that does not pose these problems. It has been suggested5" that at each composition in a liquid silicate, there is a distribution of anion sizes; thus the dominant anionic species might be Si3,O9 but as well as these anions the melt may contain say sis0:i anions. Decreasing silica content and increasing temperature are said9 to reduce the size of the dominant species. Taking this concept further, it is now suggested that these complexes are not the rigid, stable entities originally envisaged, but rather that they exist on a time-average basis. In this way large groups are continually decaying to smaller groups and small groups reforming to larger groups. The most complete transport data 8-10 available are for a melt containing 40 wt pct CaO, 40 wt pct SiO2, and 20 wt pct Al2O3. Recalculating this composition in terms of ion fractions and bearing in mind the relative sizes of the constituent ions, Table I, it seems reasonable to regard this liquid as almost close packed oxygens, containing the other ions interstitially, in which regions of local order exist. On this basis, all oxygen positions are equivalent and, since an oxygen is always adjacent to other oxygens, its diffusion occurs by successive small movements, in a cooperative manner, in accord with modern liquid theories." Silicon diffusion is much less favorable, firstly because there are fewer positions into which it can move and secondly, because it has the rather rigid restriction that it always tends to be co-ordinated with four oxygens. Silicon self-diffusion is therefore probably best regarded as being effected by the decay and reformation of anionic groups or, in other words, by the redistribution of regions of local order. Calcium self-diffusion should occur more readily than silicon, because its co-ordination requirements are not as stringent, but not as readily as oxygen, because there are fewer positions into which it can move. There is the further restriction that electrical neutrality must be maintained, hence calcium diffusion should be regarded as the process providing for electrical neutrality in the redistribution of regions of local order. That is, silicon and calcium self-diffusion occur, basically, by the same process. Aluminum self-diffusivity should be somewhere between calcium and silicon because, for reasons discussed elsewhere,&apos; part of the aluminum is equivalent to calcium and part equivalent to silicon. Consider now self-diffusion as a rate process. The simplest equation is: D = Do exp (-E/RT) [I] This equation can be restated in much more explicit forms but neither the accuracy of the available data, nor the present state of knowledge of rate theory as applied to liquids justifies any degree of sophistication. Nevertheless the terms of Eq. [I] do have significance;12 Do is related, however loose this relationship may be, to the frequency with which reacting species are in favorable positions to diffuse, and E is an indication of the energy barrier that must be overcome to allow diffusion to proceed. For the 40 wt pct CaO, 40 wt pct SiO2, 20 wt pct Al2O3, melt, the apparent activation energies for self-diffusion of calcium, silicon, and aluminum are not significantly different from 70 kcal per mole of diffusate,&apos; in agreement with the postulate that these elements diffuse by the same process. For oxygen self-diffusion E is about 85 kcal per mole,&apos; again in agreement with the idea that oxygen is transported,

Jan 1, 1963

By R. W. Kraft

The normal Mg-Mg,Sn eutectic is a classic example of a Chinese script eutectic. When the alloy is unidirectionally solidified, a much simpler topo-logical arrangement of the phase particles can be produced although individual grains still usually consist of two or more interpenetrating lamellar systerns. Specimens from unidirectionally solidified ingots were analyzed metallographicall~ and crys-tallographically, and it was found that the interfaces between the lamellae had a common crystallograPhic character describable by: Lamellar interfaces II {220}Mg2Sn 1) {1011}Mg Arguments are presented to explain why this particular orientation relationship tends to occur and it is shown that this criterion can be nearly satisfied simultaneously on up to four different lamellar systerns between two interpenetrating single crystals. Finally, on the basis of this work ad other similar work which has previously been done on Al-CuAl2 eutectics, a general principle pertaining to low-energy interfaces between two crystalline Phases is proposed. WITHIN the past few years several investigators1-4 have demonstrated that the microstructures of many eutectic alloys can be significantly altered by uni- directional solidification. If appropriate control is exercised over the purity of the alloy, the growth rate, and the thermal gradient during unidirectional solidification, ingots can be made in which the phase particles are aligned predominantly parallel to one another throughout substantial portions of the ingot. The present author has also shown for at least one of the alloys that the parallel lamellae tend to assume a unique crystallographic relationship during

Jan 1, 1963

Flat jack stress determinations in selected colliery roadways have revealed a range of measured stress from 330 lb/sq. in. tension to 3,750 lb/sq. in. compression. Photoelastic examination of loaded plastic and actual rock model mine openings has shown that the primary horizontal stress required to attain these measured stresses would be from one to three times the superincumbent vertical load.Examination of roof movement with a borehole extensometer and a series of anchors at various horizons to 30 feet in a vertical roof borehole showed that when a standing face was advanced the roof movement was practically confined to the lower two feet. The majority of this movement occurred during the 36 hours after mining at this face commenced.The use of a radioactive isotope and a scintillation counter in a pair of parallel boreholes is a sensitive and accurate method of roof bedding plane crack detection.INTRODUCTIONA knowledge of strata stresses is required to understand the deformation of an underground opening and, in particular, the roof behaviour. It is the aim of investigations currently being conducted by Australian Coal Association (Research) Ltd. to determine the stress existing around mine openings and the location and magnitude of roof movement.STRATA PRESSURE MEASUREMENTMost measurements of strata stress are performed at the surface of underground openings and the majority measure the change of strain resulting from stress relief. The accuracy of the measured value of stress depends upon knowledge of the rock modulus of elasticity. The flat jack method has the advantage that strain relief is restored by a measured stress applied directly by the jack. The rock modulus of elasticity can also be determined.

Jan 1, 1963

Drilling at Ipswich during the last twelve years by the Queensland Department of Mines has proved large quantities of reserves which have assured the security of the field for many years to come. This is perhaps the greatest contribution to the development of the field since its discovery in 1827.The drilling campaign commenced in 1950 and by the end of 1961 comprised 242 holes totalling 180,220 ft.Intersections of formations and seams, accompanied by detailed surface mapping, led to more precise knowledge of the geology of the field than was previously possible, and clarified many problems of correlation. Productive formations are part of the Middle Triassic Ipswich Coal Measures, a 4,300 ft sequence of fresh-water sediments with some interbedded volcanics. They are overlain by the Upper Triassic Bundamba Group and the Lower Tertiary Booval Group.Reserves disclosed by drilling amount to 171,487,000 tons, comprising 109,407,000 tons &quot;measured&quot; and 62,080,000 tons &quot;indicated&quot;. The security of these reserves encouraged many collieries to instal modern efficient mining machinery and washing plants.The climax of recent development of the resources of the field will be the commissioning in 1966 of a &#163;33 million 360 MW power station in the Swanbank district which will consume 14 million tons of coal during its 30 year life and will have a peak demand of some 20,000 tons per week.Drilling is continuing and is expected to prove additional reserves which will justify further development of the field.INTRODUCTIONUntil 1949 there had been no concerted effort to test systematically the resources of the whole Ipswich field. Fifty two known holes totalling 30,500 ft had been drilled, eight of them by the Department of Mines, but because of poor core recovery and inadequate records most of them were of little use in a comprehensive assessment.Development of the field was being retarded by uncertainty regarding reserves and by the general state of the coal mining industry. Numbers of comparatively small independent companies and owner groups were operating coal...

Jan 1, 1963

By Alla D. Mah

Combustion energies of barium and strontium were measured by means of the combustion bomb calorimeter. The heats of formation obtained for the oxides were ?H298.15 = -139,060 ± 700 cal/mole of barium oxide (BaO) and ?H298.15 = -144,440 ± 400 cal/mole of strontium oxide (SrO). Tables containing heats and free energies of formation from 298.15° to 2,000° K were prepared.

Jan 1, 1963

By W. Klement

By quenching liquid alloys, single-phase solid solutions are obtained in the ranges 0 to 42.0 at. pct Co-Au and 0 to 15 and 75 to about 100 at. pet Co-Cu. Metastable solid solutions are also found in multiphase 42.0 to 49.0 and 69. 0 to about 100 at. pet Co-Au alloys. fie inability to achieve complete solid solubiliiies in Au-co and cu-co alloys is rationalized by a conszderation of the rate processes during cooling and solidification. Trends in lattice distortion and shifts in the compositions of the melting-point minima and critical points are discussed for the binary alloys of copper, silver, and gold with some of the transition metals of the first long period. By rapidly cooling alloys from the melt, a continuous series of metastable solid solutions can often be obtained for components of similar crystal structure which normally form eutectic systems.&apos; The eutectic system Au-Co, Fig. 1, and the peritectic system Cu-Co, Fig. 2, were investigated in order to determine the extent of the metastable solid solutions attainable with the present technique.* EXPERIMENTAL PROCEDURES Most of the alloys were prepared by melting weighed quantities of the elements (purity greater than 99.9 pct) under hydrogen in alumina crucibles by means of induction heating. After reweighing, the alloys were cast under argon into 1 mm diam wires. However, it was not possible to prepare some of the Cu-Co alloys with the requisite homogeneity (over about 1 mm3) in this way. For these alloys, reduced powders (purity greater than 99.9 pct) were mixed for 12 to 48 hr, pressed into compacts that were sintered at 1000º to 1050°C for 6 to 48 hr under hydrogen, and then furnace-cooled. Alloy charges of a few mm3, cut from the cast wires or chipped from the sintered compacts, were heated to 1550º to 1600°C in 30 sec in an alumina insert held within a graphite support and then ejected by a pulse of helium onto a lightly polished copper strip on the inner periphery of a rotating wheel. The

Jan 1, 1963

By F. Bonaccorso, G. Venturello, C. Antonione

A study of the effect of small amounts of interstitial impurities on recovery and re crystallization in high-purity iron (99.995 pct) has been undertaken. This paper gives results on the effect of carbon, introduced in small-dosed amounts @om 0.0005 to 0.0086 wt pct) by heating iron specimens of high purity m a static atmosphere of CO + ,. The materials prepared in this way, cold-worked 80 pct and subjected to a series of isochronal and isothermal annealings, were submitted to examinations by X-rays, micrographs, and hardness tests. It was observed that effect of carbon is remarkable in the sense of blocking recovery of mechanical properties up to the temperature at which re crystallization begins. On the contrary, carbon has a negligible effect on primary re crystallization temperature, when compared with the known effect of substitutional impurities. This is in agreement with the high mobility of interstitials. In effect, only a slight decrease, -20 pct, of the grain-boundary motion rate was noted, due to the interaction between the grain boundary and the carbon atoms. On the other hand, in the samples in which the carbon content is above the solubility limit at the temperature at which re crystallization occurs, a slight increase of nucleation frequency is noted due to the presence of precipitated carbides. ThE effect of purity on recovery and recrystalli-zation phenomena has been known for a long time; however, recently, new attention has been given to the problem since new methods for obtaining metals with extremely low impurity contents have become available. Most of this research work essentially concerns the effects of impurities which cause precipitates or give rise to substitutional solid solutions. The works of Bolling and winegard1 and Aust and utter&apos; on lead, and Vandermeer and orddon&apos; on aluminum, 01sen4 on nickel, and Abrahamson and Blakeney on iron should in particular be referred to. On the effect of this type of impurities a quantitative theory has been formulated by Detert and Lucke6 and has lately been discussed critically by Cahn7 and Gordon and vandermeer.&apos; Interstitial solid solutions in iron have not as yet been studied. As the study of the effect of interstitials is of great interest both from a theoretical and practical standpoint, it was deemed useful to examine the effects of carbon, nitrogen, and boron on recovery and primary recrystallization of iron. There already is some work by Chaudron et al.,1-" on the effect of interstitials on iron; their work, however, mainly concerns secondary recrystallization. The present paper refers in particular to the effect of carbon. EXPERIMENTAL PART Preparation of Materials. The pure iron used for this research was obtained from FeCIS recrystal-lized and purified by extraction with isopropylic ether. From the ferric chloride purified in this manner, hydroxide was precipitated with a solution of very pure ammonia, and, by calcination in pure sintered alumina crucibles, oxide was obtained. Reduction of the oxide to iron sponge was performed in sintered alumina tubes with very pure hydrogen at 650°C; at the end of the operation temperature was increased to 900°C. Specimens for the experiments were obtained by sintering the sponge at 1480°C in pure Hz after a pre sinter ing treatment at 900° C. It is important to note that the treatment at 1480°C in Ha produces a further purification from more volatile elements such as zinc, cadmium, arsenic, lead, and tin. Details on the preparation and characteristics of this type of very pure iron are given in a previous work.&apos;&apos; Only the complete analysis performed by neutron-activation methodsz3 is given here, Table I. Some of the specimens prepared in this way were carburized in the 0 region with very low amounts of carbon by treating them at 700°C in a static atmosphere of Ha containing a definite amount of CO. The set-up used is described in Fig. 1. A gas-tight quartz tube containing the specimen to be carburized and an internal friction control specimen, after being evacuated, was filled with Hz

Jan 1, 1963

By Roland de Wit

Conclusions reached in a paper by weertmanl are amplified in a mathematical and graphical way. It is shown that in a stressed crystal a straight dis-location may be in a position of unstable equilibrium with respect to helix development, and how a small perturbation may start the dislocation off on its helical path. Helix development occurs by diffision; bulk diffusion is necessary for development from a screw, but core diffision is sufficient for development from an edge dislocation. For a mixed dislocation helix development can take place by core diffusion if the helix also climbs; a diffusion reversal takes place when the slope of the helix equals the slope of the Burgers vector. The work done on a crystal by the external forces is graphically shown to be consistent with the direction of motion of the dislocation in helix development. Finally a detailed mechanism for tangle formation from helices is presented. In the course of helix development a glide situation may be reached where a segment of each helix loop lies in a slip plane in which it can expand by glide. Thus is it visualized how a helix can deteriorate into a tangle. A paper by weertmanl proposes dislocation-tangle formation by a helical dislocation mechanism. The present paper amplifies Weertman&apos;s arguments in a mathematical and graphical way and presents some further ramifications of the proposed model. The importance of dislocation tangles is discussed in Weertman&apos;s paper and the references cited therein. The mechanism of their formation is not yet understood. Weertman proposes that in cold-worked crystals conditions exist suitable for the conversion of straight dislocations into helices and subsequently into tangles. Helix formation occurs by a diffusion process and Weertman proposes that at low temperatures only core diffusion is important. The present paper necessarily repeats some of Weertman&apos;s work. Since the mathematical development and notation used are slightly different from his, this was thought necessary for clarity. GEOMETRY OF THE HELIX weertman2 has shown that the equilibrium form of any dislocation line is a helix if it is assumed that the energy per unit length (line tension) of the dis- location is constant. For the special case that no external forces act on the dislocation, the helix reduces to a straight line. We shall assume in this paper that the dislocation has a helical form even when it is not in equilibrium. The parametric equation of a helix is, see Fig. l: where a is the radius of the cylinder tangent to the helix, and 270 the pitch of the helix. The pitch is related to v, the number of turns per unit length (along the axis) by the relation: When a = 0 Eq. [I] gives a straight line in the z direction. The growth of a straight dislocation into a helix is now described mathematically by letting a vary from zero to its final value. The tangent to the helix is given by where is the path length along the helix. This gives the direction of t and since its magnitude is unity we must have So that dcp/ds = (a2 +p2)-"&apos;. The curvature of the helix is given by where n = -(cos + sin) is a unit vector normal to the helix. Note that the vectors k and n always point toward the axis of the helix, Fig. 1. FORCE ON THE HELIX The external force which makes the straight dis-

Jan 1, 1963

By Henry E. Perlee

Air compressor explosions that are caused by the ignition of combustible vapor mixtures cannot be explained by a single reaction mechanism or sequence of events. Explosions have been caused by the sudden release of large quantities of lubricating oil, by the rapid vaporization of oil that had accumulated slowly in high-pressure piping, and by the production of decomposition products from carbonaceous deposits. Ignitions can be caused by the heat produced in a catalytic reaction, in a compression process, or when a shock wave is propagated through a combustible vapor-air mixture. The frequency of these ignitions can be minimized by establishing proper maintenance and cleaning schedules. Further study is needed to satisfactorily correlate the various factors involved in compressor explosions.

Jan 1, 1963