Search Documents

By R. G. Davies

WeERTMANI has shown that the high temperature steady state creep rate, i, in lead and indium-base alloys obeys an equation of the form where AH is the activation energy, o the applied stress, n the stress exponent, and R and T have their usual meanings. He observed a variation in n from 4.5 for pure metals to 3 for concentrated alloys, which he interpreted as due to Change in creep mechanism from the climb of dislocations in pure metals to a micro-creep mechanism in the alloys. The Cottrell-Jaswon microcreep mechanism of the moving dislocation taking its impurity atmosphere with it was considered to be the most likely process, although short-range order and the segregation of solute atoms to a stacking fault will also give a stress exponent of 3. Steady state creep has been investigated in a Au - 27 at. pct Cu alloy at temperatures above 1/2 TIM where TIM the absolute melting temperature. As the oxidation resistance of this alloy is excellent all tests were carried out in air with a furnace built to give a temperature variation of less than 1°C along the 60 mm gage length. A lever-arm arrangement applied the stress with a load being adjusted between each creep test to maintain a constant stress. As each test produced less than 0.5 pct creep strain, the variation in stress during the test was negligible. The creep strain was measured by a transducer at the end of one of the alloy-steel grips, with the out of balance potential being finally recorded on a variable speed chart recorder. A typical creep curve is shown in Fig. 1. The results, Fig. 2, confirm that n is nearer to 3 than to 4.5; the creep mechanism could be any of those given above. The activation energy, AH, which is independent of stress, is consistent with a diffusion controlled process; the activation energies for the self-diffusion of gold and for the diffusion of gold into Copper are both -45 kcal per ml., There is now considerable evidence, that, when the steady state creep is dependent upon diffusion, irrespective of the actual creep mechanism, the activation energy is independent of the stress. The author would like to acknowledge the financial assistance provided by the International Atomic Energy Agency, Vienna, and the Argentine Atomic Energy Commission.

Jan 1, 1962

By David Burgess

Natural gas is a general term applied to the gas obtained from oil or gas wells. It is the most widely used of all gaseous fuels. The principal disadvantage in the use of this and other gaseous fuels is the difficulty encountered in the storage and transportation of large quantities in the gas state. Handling in the liquid state is possible, but reduced temperatures are required since methane (table 1) is the principal component of most natural gases that are used as fuels. Actually, liquid storage has been utilized both here and abroad;3 however, the Cleveland disaster4 has pointed out the need for a critical evaluation of the hazards involved in the storage of this cryogenic fuel. Accordingly, a program was undertaken to obtain basic data that could be used to assess these hazards. In this report, the factors to be considered in an evaluation of the fire and explosion hazards associated with any fuel are each discussed briefly. These factors are then used to assist in the design of experiments for the evaluation of the hazards associated with liquefied natural gas (LNG) relative to those associated with other common fuels. Experiments have been conducted on the vaporization of LNG, the mixing of LNG vapors with air, the effect of temperature and nitrogen dilution on the limits of flammability of methane in air, the burning rates of LNG and other fuels, flame radiation, and extinguishment of fires above liquid pools. Based on the results of these experiments, LNG can be stored safely in suitably designed above-ground tanks surrounded by earthen dikes in much the same manner as gasoline.

Jan 1, 1962

By E. S. Machlin, A. J. McEvily

HE results of an experimental investigation by McEvily and Machlin have indicated that a strong relationship exists between the processes of cross slip and fatigue. Whenever dislocations can cross onto an intersecting plane and expand thereon, as in AgCl crystals, the usual type of S-N behavior is obtained, but when such a process is difficult, as in NaCl crystals, fatigue does not occur in its usual manner, if at all. MgO, because of its crystal structure (NaCl type) and slip systems ({110}<110>) would not be expected to fail in fatigue. However, Cornet and Gorum2 have found something akin to the usual type of fatigue behavior for MgO crystals. The purpose of this note is to attempt to resolve this apparent discrepancy. In Cornet and Gorum&apos;s work as-cleaved crystals were tested under cyclic axial loading, whereas in McEvily and Machlin&apos;s work chemically-polished crystals were tested in reversed bending. Because of the difference in specimen preparation, the major effort of the present work was directed toward comparing the behavior of as-cleaved as opposed to chemically-polished specimens. The effect of type of loading seemed less important, but a check was made on this also. Eighteen bend tests and one axial load test were made. The specimens were cleaved from Norton magnorite blocks, and measured 1 by 3/16 by 1/8 in. To avoid failures in the grips, the thickness of the bend specimens was reduced from 1/8 in. near the ends to 0.04 in. in the central portion. This reduction was from one side of the crystal only. Twelve specimens were polished in orthophosphoric acid to remove the damage due to cleavage. The other six specimens were not chemically polished so as to maintain the as-cleaved condition of the crystal faces which had not been reduced. The axial-load specimen was reduced from both faces to a thickness of

Jan 1, 1962

By Gary A. Kingston

Low-cost hydroelectric energy in the Pacific Nortnwest has been an important factor in the development of a ferroalloy industry. Eleven companies, employing approximately 1,000 persons, produce about 116,000 tons (1954-58 average) annually of ferrosilicon, ferrochromium, ferromanganese, ferrophosphorus, silicomanganese, and ferronickel. About 7,500 tons (1954-58 average) of these ferroalloys is consumed in the Pacific Northwest States of Washington and Oregon; the rest is used principally in other western and mid-western markets. In 1959, the Bureau of Mines began a study to determine the current status and to evaluate the potential of the ferroalloy industry in the Pacific Northwest. The Bureau gathered information from operating alloy plants in Oregon, Washington, Idaho, and Montana; from published materials; and from consumers of ferroalloys.

Jan 1, 1962

By B. H. Kear

Clustering of slip bands in different systems has been observed in both ordered and disordered Cu3Au crystals compressed in the <110> orientation. Certain features of the slip band patterns are explained in terms of reactions between dislocations with Burgers vectors at 120 deg; in a few rare cases, the slip band evidence suggests that the Products of such reactions form diffuse tilt boundaries between the differently slipped regions of the crystal, similar to the known behavior of ionic crystals, but not nearly so well defined. WHEN crystals with orientations favorable for multiple slip undergo plastic deformation, slip may occur in different systems in localized regions, so that clusters of slip bands are developed. This phenomenon has been observed in fee1-4 metals and also in ionic crystals having the sodium chloride structure.5-8 In the ionic crystals, the boundaries formed between the differently slipped regions of the crystal assume characteristic orientations and are associated with macroscopic tilts that are plainly visible on the sides of the crystal. Recently, this interesting feature was explained in terms of the formation of diffuse low-angle boundaries as a result of interactions between families of glide dislocations in the different systems meeting in the boundaries.9 This paper describes an attempt to obtain similar evidence for boundary formation in an fee crystal. The alloy Cu3Au was chosen for the present study simply because this material is currently being used in a general study of differences in deformation behavior of the ordered and disordered phases of this alloy, which will be described elsewhere. EXPERIMENTAL PROCEDURE The two specially oriented compression specimens used in the present study were prepared from a melt-grown single crystal by careful cutting, grinding and polishing. The finished specimens were about 6 mm by 2 mm in cross section by 6 mm tall, with their ends parallel to (101) and sides parallel to (111) and (121); the broad faces of the specimens were made parallel to (711). Both specimens were annealed in an evacuated quartz tube at 850oC for several hours, slowly cooled to 500°c, and then quenched into water in order to obtain the disordered state for the alloy. One of the specimens was partially ordered (with S- 0.8) by reannealing at 350oC for 100 hr. After these annealing treatments, both of the specimens were electropolished. 10 Finally, the specimens were compressed in the [loll orientation and their stress-strain curves were recorded. The deformation was carried out in increments of a few percent strain. At each stage in the deformation the specimens were unloaded, removed from the compression jig, and examined optically for slip bands. Before reloading, the specimens were repolished, so that the observed slip band patterns were characteristic of a particular stage in the deformation. EXPERIMENTAL RESULTS Fig. 1 show!; the stress-strain curves for the ordered and disordered specimens and also indicates the stages 1, 2, and 3 where the deformation was interrupted for examination of slip bands. The curves show marked differences in flow stress and in work hardening rate in the two specimens, as observed by previous workers.11,12 Also, it was found, in agreemement with the observations of Taoka and Sakata,&apos;3 that the plastically deformed disordered alloy showed the characteristic coarse slip bands of alloys, whereas the ordered alloy exhibited a fine slip band structure similar to that of pure metals. Slip Band Observations. In what follows, the description of the slip band patterns, with accom-

Jan 1, 1962

Deposits of manganese oxides and silicates in the Tamworth area were re-examined. The major deposit at Danglemah consists chiefly of rhodonite and the rare silicate tephroite. It is considered that the manganese was deposited with the original sediments, the silicates being formed later during the intense folding and low-grade metamorphism of the enclosing rocks.INTRODUCTIONMany small deposits of manganese oxides and silicates occur along a belt of eastern New South Wales and Queensland.Some fifty occurrences, most of which have been subject to mining activity, were described by Lloyd (1943) and some of this information was summarized by Knight (1947). The ores have been mined on a small scale since 1884. Small supplies of battery grade ore were won from a number of deposits, while larger quantities of metallurgical grade were sold to the steel industry. Maximum production was in 1918, when 6,500 tons were mined.The siliceous nature of many of the ores and their occurrence in the neighbourhood of granite batholiths led earlier investigators to consider the deposits to be of hydrothermal origin, associated with the granite intrusions. The present work questions this viewpoint.In this investigation, three of the chief deposits in the Tamworth area were seen. These were at Danglemah, which is being mined at present, and Mount Jasper and Manganese Mountain, which were mined in the past. The Danglemah mine is the most accessible and yields the best material...

Jan 1, 1962

By Clyde N. Garman

Historically, Vanadium and Uranium have been precipitated together in carbonate sill circuits. A separation of the salts of the two metals was then made on the basis of the fact that the reduced, salts of vanadium are more solo to and those of uranium lose soluble than the respective salts of higher valence. In practice this was carried out by fusing the precipitated combined concentrate with salt, sodium carbonate and sodium hydroxide with oil soaked sawdust mixed into the charge as the reducing agent. Generally the fusion was carried out batch wise and the resulting slag or glass leached in water. A good, fusion and three or four decantation washes resulted in almost complete recovery of the vanadium in the liquid phase and a very high recovery of the uranium as a dense black U02 solid.

Jan 1, 1962

By d&apos, Kathleen J. Amico

THIS SUAMMARY is shown in Minerals Yearbook volumes I and III of this series on mineral production in the United States, its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico, and on the principal minerals imported into and ex- ported from the United States. The several commodity and area chapters contain further details on production. A summary table comparing world and U.S. mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed "mine output." It usually refers to minerals in the form in which they are first extracted from the ground, but customarily includes for some minerals the product of auxiliary processing operations at or near mines.

Jan 1, 1962

By Douglas J. Harvey

The surface tension of lead-tellurium alloys (in the range 0 to 6.70 at. pct Te) ad lead-arsenic alloys (in the range 0 to 10.53 at. pct As) has been examined by the maximum bubble pressure method. The surface tension of high purity lead can be expressed over a range of temperatures (M.P. to 750°C) by the relationship = 512 — 0.133t. Arsenic and lellurium were both found to be surface active in lead. The surface excess concentration at 700°C was .found to be constant at 0.74 x 10-10 moles per sq cm for tellurium. The surface excess of arsenic at 700°C varied between 0.26 x 10-10 moles per sq cm at 0.16 at. pct to 1.5 x 10-10 moles per sq cm at 8.3 at. pet. The surface tension of lead has been investigated sporadically over the last 90 years. The first recorded study was made by Quincke1 who used a rather crude application of the drop-weight method. Hogness2 obtained the first reliable value for the surface tension of lead by measuring the pressure necessary to force the liquid metal from the end of a small capillary of known radius. Hogness gives the empirical formula: ?(surface tension)= 444 - 0.077 (l-327) which describes the relationship between surface tension and temperature ("C); This work was followed by that of Bircumshaw3 who applied the two-capillar maximum bubble pressure method of Sugden.4 The values published by Bircumshaw are in good agreement with those found by Hogness. Matuyama5 examined the surface tension of lead by the drop weight method. However, the values found are somewhat higher than those previously reported. More recent investigations by Greenaway6 and by Melford and oar&apos; have resulted in data which are not in close agreement, but which are well within the expected range at most temperature levels. The study of the surface tension of lead alloys began with Drath and sauerwald8 who examined the lead-bismuth system. They found that the surface tension values of the alloys in this system deviated only slightly from the ideal mixture rule. Matuyarna5 examined the lead-antimony system. Bircumshaw the lead-tin, and the lead-indium system was studied by Hoar and Me1ford.10 The results of these investi- gations are summarized in Fig. 1. It may be seen that the data vary only slightly from the ideal mixture rule. As none of the metals studied and reported in the literature has a very interesting effect on the surface tension of lead,*the next logical step might be to examine the effect of metals of low solubility or nonmetals having some liquid solubility. Baes, and Kellogg11 have pointed out that the elements most likely to be surface active in liquid metals are ones of limited solubility in the liquid state and possessing weak intermolecular bonding forces in the solid state. Therefore, Group V, VI and VII nonmetals are most likely to be surface active. It was decided to examine the effect of a borderline metal, arsenic, and a nonmetal tellurium. Arsenic forms a eutectic with lead having a melting point of 290°C and a composition of 6.9 at. pct As.13 Pure arsenic sublimes when heated above 610°C. Even though alloying with lead lowers the vapor pressure, fumes containing arsenic are evolved at a very noticeable rate when lead-arsenic alloys are heated above 650°C. Tellurium raises the liquidus temperature of lead sharply to 904°C,14 the melting point of PbTe (lead-telluride). The solid solubility of tellurium in lead was determined by Greenwood and worner15 to be 0.0007 at. pct at room temperature. EXPERIMENTAL METHOD Surface Tension Measurement—The two capillary maximum bubble pressure method for measuring surface tension developed by Sugden,4 and used later

Jan 1, 1962

By E. T. Turkdogan, P. Grieveson

STAFF: Editor, Gerhard Derge Acting Editor, Paul G. Shewmon Carnegie lnstitute of Technology Sc hen ley Park Pittsburgh 13, Pa. Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: Karl L. Fetters, President; J.S. Smart, Jr., Past-President; R. C. Cole, Vice President; R. L. Hennebach, Treasurer; R. W. Shearman, Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: W. 0. Phil-brook, Chairman; H. L. Bishop, R. C. Cole, J. N. Hobstetter, W. A. Krivsky, E. R. Morgan, F. C. Langenberg, R. E. Lund, Paul Queneau, L. L. Seigle, R. L. Smith, and T. &apos;4. Wainwright. Review and selection of manuscripts is under the supervision of the following Publications Committes: Extractive Metallurgy Division: R. E. Lund, Chatrmon; M. E. Wodsworth, Vice Chairman; D. H. Baker, Jr., G. M. Bell, R. E. Groce, W. A. Krivsky, R. A. Lewls, Charles O&apos;Neill, A. W. Schlechten, R. E. Shinkoskey, and W. W. Stephens. Iron and Steel Division: T. V. Wainright, Choirman; H. L. Bishop, R. E. Boni, T. E. Dancy, C. W. Murphy, Johonnes M. Uys, J. B. Wagstaff, and R. G. Ward. lnstitute of Metols Division: J. N. Hobstetter, Chairman; P. A. Beck, J. J. Becker, G. F. Bolling, J. O. Brittain, J. 8. Clark, R. S. Davis, A. E. Dwight, R. W. Fountain, L. R. Girifalco, J. C. Gurland, H. S. Kclish, E. L. Harmon, J. J. Heger, A. A. Hendrickson, L. Himmel, J. P. Hirth, H. H. Johnson, Jr., R. R. Nosh, T. N. Rhodin, R. H. Richman, H. C. Rogers, W. Rostoker, C. Sherby, C. W. Spencer, L. Slifkin, J. K. Stanley, R. Steinitz, H. C. Stumpf, and R. Swolin. Published bimonthly by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc., 345 East 47th Street, New York 17. N. Y. Telephone PLaza 2-6800. Subscription $30 per year for non-AIME members in United States and North, South, and Central America; $32, foreign; $7.50 for AlME members. Single copies, $6.00, single copies foreign, $6.50. The AlME is not responsible for any statement made or opinion expressed in its publications ... Copyright 1962 by the American lnstitute of Mining, Metollurgical. and Petroleum Engineers. Inc. . . . Registered cable address, AlME New York . . . Indexed in Engineering Index, lndustriol Arts Index, and Chemical Abstracts . . . Second class postage paid at New York, N. Y., and Ann Arbor, Mich. Volume 224, Number 6.

Jan 1, 1962

By S. M. Purdy

Under certain conditions of hot rolling and air cooling from the hot-rolling temperature, bars of a high carbon (0.40 pct C) chrome-nickel austen-itic alloy were found to show magnetism even though no ferrite or martensite could be detected by microscopic or X-yay methods. The appearance of magnetism in such alloys may come from chromium impoverishment of the austenite grains near the precipitated carbide particles. SPORADICALLY, hot-rolled bars of Silchrome 10, an exhaust valve steel, have been found to be magnetic. Because of the analysis of the alloy—0.40 pct C, 18 pct Cr, 8 pct Ni, 3 pct Si —magnetism is unexpected. Preliminary investigation showed neither martensite nor ferrite to be present; only austenite and Cr23C6. Since a literature search was fruitless, a brief study was made of the appearance of magnetism in this alloy. The only basic difference between the two heats is the nitrogen content. Permeability was measured using a Severn magnetic gauge. This instrument consists of a magnet mounted on a counterbalanced arm. A set of calibrated plugs is placed in contact with one pole of the magnet. The specimen is placed close to the other pole of the magnet. If the specimen pulls the magnet away from the plug, it has a permeability greater than that marked on the plug. This technique is swift and reproducible. Previous experience has shown that the permeabilities obtained corresponded to those obtained on a permeater with a field strength of 100 oe. Specimens from both heats were annealed at temperatures between 1700 and 2300°F. One set of specimens was water cooled and another furnace cooled. All the water-quenched specimens were non-magnetic; the furnace cooled ones were magnetic as shown in Table I with no difference being observed between the two heats. Microstructural examination of the specimens showed the expected increase in carbon solubility with increasing temperature. Carbide solution was complete at 2200°F. The specimens heated to 1900°F or below showed some carbide precipitation from the hot-rolled structure. A furnace cooled specimen from a given temperature showed less carbide out of solution than the water-quenched specimen from the next temperature below; e.g., the specimen furnace cooled from 2100°F showed less carbide out of solution than the water-quenched specimen from 2000" F. These studies indicated that the appearance of magnetism was not related to the quantity of carbon in or out of solution and it was related to precipitation at temperatures below 1700" F. A set of samples annealed and water-quenched from 2100° F was aged for 4 hr at temperatures between 1000" and 1600°F; all were non-magnetic. A second set of samples, similarly annealed, was aged 1 to 24 hr at 1200°F with the results shown in Table II. None of the latter set of specimens showed magnetism until they had been aged about 8 hr. Magnetism was quite strong after aging 24 hr. X-ray diffraction studies on several of the magnetic specimens showed that the austenite had a lattice parameter of 3.58A and that the carbide was Cr23C6. Several of these samples were electrolytically digested in 10 pct HCl in ethanol, with a current density of 0.1 amp per sq cm. None of the particles in the residue were magnetic. Accidentally, one cell was run at 1 amp per sq cm; e.g., magnetic particles were found in this residue. After careful separation, the magnetic particles were mounted on a quartz fiber and their diffraction pattern determined using a 5.73-in. Debye-Sherrer camera with CrK radiation. These particles showed a fcc structure with a lattice parameter of 3.57A. Prolonged exposure, up to 16 hr, produced no other lines on the film. The following facts seemed to be established at this time: 1) Austenite was the magnetic phase. 2) Neither ferrite nor martensite could be detected. 3) Magnetization could be produced by aging at 1200°F. One explanation of these data is that the carbide precipitation impoverishes the region immediately around the carbide particle of carbon and chromium and increases the proportion of nickel. All of these serve to increase the Curie temperature of the region around the carbide particle. If the composition change is enough, the Curie temperature will rise above room temperature. If the volume of the affected region is great enough, the magnetism will become detectable. At low aging temperatures, composition changes are great enough but the overall volume of impoverishment is quite small

Jan 1, 1962

By F. J. Plecity, J. T. Michalak, W. C. Leslie

Isothermal recrystallization and grain growth in zone- and vacuum-melted irons and Fe-Mn alloys, up to 0.60 pct Mn, were studied in the range 480° to 650° C, after 60 pct cold reduction. In initial stages, rate of grain growth and rate of recrystallization of iron decrease with time. The recrystallization is typical of a growth-controlled process, and rate of growth is determined by the extent of recovery. Mn decreases rates of growth and of recrystallizatzon. The recrystallization process changes at about 0.30 pct Mn and nucleation may become time-depetzdet~t. In recent years, considerable effort has been expended in determining the effects of solute elements on recrystallization and boundary migration in fcc metals. The results have indicated that the effects produced by single solute additions are dependent upon both the element added and its concentration.&apos;-&apos; In contrast, there have been very few attempts to determine the characteristics of recrystallization and boundary migration in high-purity bcc metals, especially after heavy deformation, and the effects thereon of single solute elements.9-11 This study was undertaken to determine the recrystallization characteristics of various "high-purity" irons and the effects of manganese additions at two levels of base purity. It was hoped that the information obtained would improve our understanding of the recrystallization of pure metals and aid in formulating a theory for the effect of solute elements. The interest was not entirely academic, for the annealing of low-carbon steels, which is of very great commercial importance, is but poorly understood. MATERIALS The compositions of the irons and iron-manganese alloys used are listed in Table I. The zone-melted iron and Fe-Mn alloys were made by Battelle Memorial Institute. Iron S-1 was arc-melted in a water-cooled steel mold in an argon atmosphere. The ingot was forged into a bar, then given two horizontal zone-refining passes in an alumina boat. Iron V-4 was treated in a similar manner, but was not zone-refined. The iron for the zone-melted Fe-Mn alloys was induction melted in vacuum in MgO crucibles and cast into alumina molds. The ingots were forged into bars, machined to shape, and a groove milled down one side of each. The best available electrolytic Mn was placed in the grooves, and the bars were zone melted. The vacuum-melted Fe-Mn alloys were induction melted in this Laboratory in MgO crucibles and poured into cast-iron molds. Iron V-5 was purchased from National Research Corp. in the form of a small vacuum-cast ingot. The low-carbon steel was made by induction melting in air at the U.S. Steel Corp. Applied Research Laboratory. The history of the materials prior to the final cold reduction differed; these details are given in the Appendix. The penultimate grain size of the principal materials was kept in the range ASTM 2 to 4, except for the low-carbon steel. PROCEDURES The cold work prior to the final recrystallization anneal was kept constant at 60 pct. It is known that rolling procedure can influence the kinetics of recrystallization of ironI2; therefore, all specimens were rolled in one direction only, between clean,

Jan 1, 1962

By D. Walton

The effect of small solute additions of Cu on the activation energies for creep A1 single crystals were determined over the range from 78° to 850° K. Below 240°K and above 800°K activation energies were unchanged. Between 240°K and 400°K strain aging causes the creep rate to become vanishingly small and the flow stress was independent of the temperature. Between 500° and 50°K the activation energy was increased to 41,000 cal per mole. NUMEROUS investigationsL have shown that solid solution alloying invariably increases the flow stress. A typical example is documented in Fig. 1. Such increases in flow stress can arise from two general effects: Alloying can increase the long-range stress fields through which dislocations must move by causing appropriate clustering; modification of dislocation densities, and so forth. Alloying can also modify the short-range stress fields that determine the activation energies for thermally stimulated migration of dislocations, such as occurs in some solute atom pinning processes, and so forth. Actually both long- and short-range stress-field effects can occur simultaneously. It was the purpose of this investigation to evaluate the effect of alloying on the short-range stress fields by determining the effect of alloying on the activation energies for creep. The resulting observations also shed some light on the effect of long-range stress fields on dislocation processes. EXPERIMENTAL TECHNIQUE Single-crystal bars (6 in. long 3/8 in. wide and l/4 in. thick) of dilute solutions of Cu in A1 were seeded, so as to provide extensive single slip, with the pole of the tensile axis located in the standard stereographic projection as shown in Fig. 2. Each crystal was grown under an argon atmosphere in a graphite mold containing a large reservoir of molten alloy for the purpose of obtaining rather uniform composition of Cu along the length of the bar. The nominal compositions of the alloys which were produced from 99.99 pct Cu and high-purity A1 containing 0.001 pct Fe and 0.001 pct Si, are given in Table I. Strains, measured by linear variable transformers attached by quartz rods to a 3 in. gage section were sensitive to and the stresses were ap- plied by direct loading of the specimen. Temperatures were determined by thermocouples attached to the gage section of the specimens. Below 400°K the apparent activation energies for creep, Q, were determined by the effect of small, rapid changes in temperature of about + 10°K from T1 to T2 on the corresponding creep rates ?1 and ?2 during primary creep according to where R is the gas constant.&apos; Above 400°K, Q was evaluated from Eq. [1] for the secondary creep rate using temperature changes of about ±20K. A typical set of results is shown in Fig. 3. RESULTS AND DISCUSSION The previously obtained effect of temperature on the apparent activation energy for creep of single crystals of high-purity A12 is shown by the broken curve of Fig. 4. The datum points on the same graph illustrate the effect of dilute a solid solution alloying with Cu on the activation energy between 600" and 750°K. Each plotted point is the average of not less than five independent test values between 600° and 750°K and not less than three at other tempera-

Jan 1, 1962

By H. J. Fisher, J. L. Walter

Two types of Si-Fe columnar ingots with preferred crystal orientation have been produced: a) ingots with (0011 directions of the crystals parallel to the longitudinal ingot axis and b) seeded ingots in which all crystals have the (100) [001]orientation with respect to the sides of the ingot. Measurements of freezing rates and temperature gradients indicated that columnar freezing occurred as long as the temperature gradient ahead of the solidification front was greater than zero. THE development of preferred orientations or textures in wrought metals may be influenced by the presence of a preferred crystal orientation in the ingot from which the product was made. The deliberate introduction of preferred orientation in the ingot for the express purpose of producing a particular preferred orientation in the wrought product has not, to the authors&apos; knowledge, been reported in the literature.* This report describes the prepara- tion of ingots of 3 1/4 pct Si-Fe in which preferred orientations near (100) [001] were produced. These ingots were subsequently rolled to strip, 0.012 in. thick, to provide a sufficient quantity of polycrystal-line sheet having the (100) [001] orientation or "cube-texture" to evaluate the magnetic properties. The properties; and test results showing the advantage of the cube-textured Si-Fe magnetic sheet over magnetic sheel having the (110) [001] texture or "Goss" texture have been reported elsewhere.&apos; The rolling and recrystallization textures of single crystals of silicon-iron having orientations near (100) [001] have been studied by Walter and Hibbard.2 They found that if the crystal has an original orientation such that the (100) plane is within 30 deg of the rolling plane, the recrystallization orientation will approach (100) [001]. If the (110) plane is nearly parallel to the rolling plane,

Jan 1, 1962

As modern techniques of Petroleum Exploration and Development are rela-tively new in Australia,2 the alien terms "Mud Logging" and "Core Analysis" will bear explanation. Mud Logging and Core Analysis are two of the Petroleum. Industryts most useful "tools" in the successful search for, and development of, commercial oil and gas deposits. Modern Mud Logging could be more accu-xately termed "Drill Cuttings and Mud Gas Analysis". Presently, mud-logging has its greatest application in exploratory wells where subsurface geologic control is at a-minimum.

Jan 1, 1962

By Robert H. Merrill

Several investigators have obtained solutions for the concentration of stress around circular, ovaloidal, elliptical, and rectangular holes in an elastic, isotropic, semiinfinite plate subjected to uniaxial and biaxial stress. These solutions are used to evaluate the changes in stress around openings immediately under the undercut normally used in conventional block caving operations. The evaluations are based on the assumption that a horizontal undercut removes most of the vertical component of a biaxial stress field. The location and magnitude of the significant changes in stress concentration around the opening are computed. Conditions under which the assumptions used in the evaluations may or may not be consistent with conditions around block caving mines are discussed, and examples of preferred opening shapes for a biaxial (hydrostatic) stress field are shown. This report is a summary of one phase of an investigation to establish design methods for the size and shape of mine openings used in block caving mining methods .

Jan 1, 1962

By Vittal S. Bhandary, B. D. Cullity

Swaged iron wire has a cylindrical {001} <110> texture. The texture is also cylindrical after re-crystallization in the absence of a magnetic field, but <111> and <112> components are added to this texture when recrystallization occurs in a field. The mecizanical properties in tension and in torsion are not greatly altered by these changes in texture. AS shown in a previous paper,1 cold-worked wires of the two fcc metals copper and aluminum can be made relatively strong in torsion and weak in tension, or vice versa, by proper control of preferred orientation (texture). The deformation texture can be controlled by selection of the starting texture (texture before deformation), because certain initial orientations are stable during deformation. The present paper reports on similar work performed on bcc iron. In this case it was clear at the outset that there was no hope of controlling the deformation texture, which is one in which <110> directions are aligned parallel to the wire axis. (1t has usually been regarded as a fiber texture, but Leber2 has recently shown that it is a cylindrical texture of the type {001} <110>. In either case, <110> directions are parallel to the wire axis.) There is general agreement on this texture among a large number of investigators, which in itself suggests that the starting texture has no influence on the deformation texture. More direct evidence was produced by Barrett and Levenson,3 who reported that iron single crystals of widely varying initial orientations all had a single <110> texture when cold-worked into wire. Thus <110> is a truly stable end orientation for iron and probably for other bcc metals as well. Under these circumstances attention was directed to the possibility of controlling the recrystallization texture. This texture is normally <110> in iron,4 just like the deformation texture. However, it is conceivable that this texture could be modified by a proper choice of the time, the temperature, and what might loosely be called the "environment" of the recrystallization heat treatment. In the present work the environmental factor studied was a magnetic field. The effect of heating in a magnetic field ("magnetic annealing") on recrystallization texture has been investigated by Smoluchowski and Turner.5 They found that a magnetic field produced certain changes in the recrystallization texture of a cold-rolled Fe-Co alloy. The texture of this material is normally a mixture of three components, and the effect of the field was to increase the amount of one component at the expense of the other two. Smoluchowski and Turner concluded that the effect was due to magnetostriction. With the applied field parallel to the rolling direction, the observed effect was an increase in the amount of the texture component which had <110> parallel to the rolling direction. In the Fe-Co alloy they studied, the magnetostriction is low in the <110> direction and high in the <100> direction. Thus nuclei oriented with <110> parallel to the rolling direction will have less strain energy than those with <100> orientations and will therefore be more likely to grow. In a later paper on the same subject, Sawyer and Smoluchowski6 ascribed the effect to magneto-crystalline anisotropy and made no mention of magnetostriction. In the papers of Smoluchowski et al. the intensity of the magnetic field was not reported but it was presumably large, inasmuch as it was produced by an electromagnet. In the second paper6 it is specifically mentioned that the specimens were magnetically saturated. But if magnetostriction has a selective action on the genesis of stable nuclei during recrystallization, that selectivity must depend only on differences in magneto-strictive strains between different crystal orientations and not on the absolute values of those strains. Thus the saturated state does not necessarily produce the greatest selectivity, because the relative difference in magnetostrictive strains between different crystal directions may be larger for partially magnetized crystals than for fully saturated ones.7 In the present work the specimens were subjected to relatively weak fields (0 to 100 oe) produced by solenoids. MATERIALS AND METHODS Armco ingot iron rod (containing 0.02 pct C and 0.19 pct other impurities) was swaged from 0.25 in. in diam. to 0.05 in., a reduction in area of 96 pct. The mechanical properties in tension and torsion were measured as described previously.&apos; Textures were measured quantitatively with chromium or iron radiation and an X-ray diffractometer,8,1 and

Jan 1, 1962

By R. L. Frantz, R. W. Bouman

The authors investigated the comminution of quartz and limestone mixtures in a ball mill, showing that the distribution modulus of a comminuted material is the same whether it is ground separately or as part of a mixture. Analysis of the ground products indicates that quartz and limestone consume energy during ball milling in proportion to their mass fraction in the mixtures. Recently Schuhmann&apos; made a significant contribution to comminution theory by proposing that complex comminution operations comprise the summation of many individual comminution events. By means of the single comminution event hypothesis, Schuhmann derived the Charles energy-size reduction relationship by considering that fragments of every particle crushed during a single impact have a size distribution characterized by the Schuhmann size distribution. In this paper, the size reduction of mixtures of solids in ball mills is analyzed by considering that size reduction occurs as many single comminution events. If a mixture of two materials is being ground in a ball mill, each successful impact of a ball with a particle of one material should yield an assembly of particles whose size distribution is characteristic of that material. Considering both materials to follow the Schuhmann size distribution equation, the size distribution of material 1 in the product is

Jan 1, 1962

By Edward B. Dismukes, Walter R. Dickson

Measurements of current efficiency at an iron anode during the electrolysis of FeO-CaO-SiO2 melts contained in an iron crucible indicate that compositions of high SiO5 content conduct current almost entirely by ionic mechanisms. Hozueuer, compositions of high metal oxide content give euidence for considerable nonionic conduction that can be attributed to p-type semicon-duction. Measurements of transference numbers in a Hittorf-type cell show that both calcium and iron ions are important contributors to ionic conduction. ELECTROCHEMICAL properties such as conductance, transference numbers. and oxidation or reduction at an electrode have been studied as means of delineating the structure of simple silicate melts that are related to the more complex slags encountered ir steelmaking processes.&apos; Measurement of these properties has strengthened the concept that molten silicates are constituted of metal ions and of silicate networks. Typically, the magnitude of electrical conductivity and the extent of agreement with Faraday&apos;s law have given evidence for ionic structures, and transference numbers have shown cations to be the exclusive carriers of electrical charge. However, melts containing oxides of iron, FeO in particular, have been found to exhibit nonionic conduction of curx,ent. The work by Inouye, Tomlinson, and chipman&apos; demonstrated semiconduction, presumably of the p-type, in molten wüstite. Simnad, Derge, and George3 and Dukelow and Derge,4 in studying the electrolysis of FeO-SiO2 and FeO-MnO-SiO2 melts, concluded that p-type semi-conduction occurs in these systems, although ionic conduction is generally favored by increased percentages of MnO or SIO2. Previous research on the electrochemistry of

Jan 1, 1962

By P. J. Routledge

THE purpose of this paper is to discuss the practical aspects of locating gravel deposits and of establishing efficient, portable concrete aggregate beneficiation plants for use on construction projects where limited amounts of high-quality gravel and sand are required. Certain projects are listed, in order to demonstrate the wide variety of problems encountered. Routledge Gravel Contractors Limited, North Vancouver, have supplied concrete aggregate for construction projects in British Colum-bia since 1957. In tl1at year, in sup-plying aggregate for a small project at a site on the northern coast of British Columbia, our quote was as follows: Concrete aggregate to specifications, f.o.b. scow, North Vancouver$ 1.75 per cu. yd. Scowing charges to site. $16.00 per cu. yd. At that time, our company realized that more attractive quotations could be submitted if local gravel was utilized where available. Port-able equipment was then acquired and a simple screening plant (Figures 1 and 1a) was at first used. This was later replaced by heavier, more versatile equipment. The use of suitable equipment, the keeping of cartage to a mini-

Jan 1, 1962