Search Documents

By Donald E. Redmon

Industrial engineering departments perform staff duties and are most effective when sincerely supported by management. In accordance with the needs and desires of the mining companies involved, various industrial engineering functions have been adopted widely at western metal mines during the period 1950-60. Newly organized departments usually conduct method and equipment studies, work-measurement programs, and establish and maintain production standards. Supervisor-training programs and courses are effective in showing the relationship between supervisory responsibility and the purpose for which industrial engineering is practiced. Industrial engineering staffs of western metal mines are composed predominantly of personnel from within the companies. Experienced industrial engineers, not necessarily experienced in mining, frequently are hired by a company to help establish the department. Management consultants frequently are called upon to advise management and instruct department personnel in industrial engineering practices. Some departments have developed satisfactory industrial engineering programs without benefit of formal industrial engineering training or advice.

Jan 1, 1962

By T. L. Myron

To determine the effect of flux crystal size on the production rate and strength of sinter, batch sintering tests were conducted on samples of both dolomite and limestone of various crystal sizes. In addition, calcination tests .were performed on the dolomite and Limestone to determine the effect of crystal size on calcination rate at various temperatures normally attained in sinter beds. The results indicate that flux crystal size does not affect sinter production rate or sinter strength.

Jan 1, 1962

By W. T. Hicks

Visual observation of the oxidation of columbium shows that the protective behavior noted previously in gravimetric work in the early stages of the reaction below 600°C and throughout the reaction at 640°C is associated with an adherent oxide. The fact that the oxide is seen to move outward from the metal at temperatures from 550° to 935°C implies that the reaction takes place at the oxide-metal interface throughout this temperature range. THE work described in this paper further clarifies the complex oxidation kinetics of Cb revealed, for example, by the continuous gravimetric studies of T. L. Kolski.1 Time-lapse motion picture studies reveal details of the reaction not provided by a study of the combustion products. EXPERIMENTAL PROCEDURE Cb specimens were prepared from material with the following typical analysis: 0, 0.03 pct; N, 0.002 pct; C, 0.006 pct; Ta, 0.04 pct; Fe, 0.01 pct; Ni <0.003 pct; and Cr <0.003 pct. Arc-cast ingots were swaged and cold rolled into slabs. These slabs were machined into blocks 7/16 by 7/16 by 7/16 in; 1/16-in. holes were drilled through the large face of the blocks for suspension. The samples were then de-greased and annealed 1 hr at 1200°C in vacuum. The sample was suspended by a platinum and Pt 10 pct Rh thermocouple inside a 1-in. quartz tube in a Kanthal wound furnace (2 in. OD by 4 in. long) equipped with windows 1/2 in. sq. A Cine-Kodak Special II 16 mm motion picture camera was trained on the sample through a Spencer microscope adjusted so that a magnification of X1.5 resulted on the film. Super Anscochrome film was used to record the events in color. Argon was flushed through the furnace while the sample came to temperature. The argon was then replaced by a stream of dry oxygen at 1 atm. Pictures were taken at the rate of eight per second for about 20 sec during the change of atmosphere. Then by use of a Stevens time-lapse device pictures were taken at the rate of four per minute starting within 1 min of the initial oxygen flow. In this manner continuous visual records of the oxidation of pure Cb

Jan 1, 1962

By Jean Howard, E. V. Walker

ManY papers have been published during the last few years on the formation of cube texture in 3 1/4 pct Si-Fe, e.g., those of Assmus, Detert, Dunn, and Walter.1,5 All are concerned with the formation of the texture by a process involving secondary re-crystallization and the relative surface energies of (100) and other planes under certain conditions of annealing. The authors have found that cube texture can also be produced by heavily cold rolling strip in which the cube-on-edge texture has first been formed. Cube texture develops on annealing, but in this case it is not accompanied by secondary recrystallization. The starting material is a sintered compact, the preparation of which has been described elsewhere. Using a conventional processing schedule employed for producing commercial silicon-iron with the cube-on-edge texture, the sintered compact is cold rolled to such a thickness that, after annealing in pure hydrogen for 24 hr at 1350&apos;~ to produce the cube-on-edge texture, the final thickness required can be obtained by giving a further cold reduction of 85 pct. Cube texture is developed by annealing at -900~~ in pure hydrogen: it has been produced in strip up to 0.024 in. thick. The microstructure of the strip consists of a mass of small primary grains within the boundaries of the much larger secondary grains which ex- hibited cube-on-edge texture before the final cold roll. If the strip is annealed at -1000 after the 85pct reduction, secondary recrystallization begins to take place, provided a strong cube texture is present. On raising the temperature more secondaries grow, complete secondary recrystallization being obtained on annealing at -1150&apos;. From this it is concluded that the secondary crystals are produced by the texture inhibition mechanism: they show (110) and (111) planes in the surface of the strip, the former being the more numerous. It has been observed that the more perfect is the (110) [001] texture prior to cold rolling by 85 pct, the further from the ideal is the (100) [oo].] texture. A similar treatment applied to high quality commercial grain-oriented silicon-iron strip failed to produce cube texture. The tilt and rotation of the [loo] from the rolling direction was less than 10deg, but (to within a few degrees) the planes (130), (450) and (210) lay in the surface of the strip. Acknowledgment is made to the Engineer-in-Chief of the British Post Office for permission to use the information contained in this note.

Jan 1, 1962

By A. E. Belton

The individual projections for large mines in the Pittsburgh coal seam in northern West Virginia are discussed with emphasis on roof control and ventilation requirements. All four mines use continuous miners with panel belts and rail for main line haulage. Both development and retreat-type mining are covered. There are a variety of mining projections being used currently in northern West Virginia. To discuss each would be impossible, so an arbitrary cross section has been selected in an attempt to indicate a fair degree of representation. Four mines, hereinafter referred to as Mines A, B, C and Dl will be discussed separately. The greater part of northern West Virginia coal production is mined from the Pittsburgh seam. This is the seam worked by all the mines discussed here. Although the coal bed outcrops at the eastern and southernmost points, these mines are all working in a depth ranging from 400 to 1400 ft below the surface. Some steep gracles have been encountered but are only considered local in nature; the overall average dip of the seam is 1 1/2 % northwest. In each of the operations the particular mining scheme used has proved advantageous, since they have been designed to satisfy particular equipment and/or physical condition requirements. So regardless whether such projections utilize a partial or full recovery principle, the productivity performances appear better than average. MINE A Full retreat is the basic mining approach for mine A, although current mining is primarily in the entry-driving stages to expand territory in preparation for pillar work. Only one section unit now on retreat. The average clean coal production at this mine is 7000 tons per day. Initially, a ripper-type miner was used for development at this mine. But with a rather weak roof overlying the coal bed and the greater horizontal span left at the top by a ripper machine, roof control became a critical problem. Even though roof bolts were used concurrently in the mining cycle for initial support, the majority of the roof in these entries

Jan 1, 1962

By R. Stickler, A. Vinckier

An optical and electron microscope study was made on a commercial 302 stainless steel heat treated for massive carbide precipitation. Convincirg evidence was obtained that the grain boundary precipitate does not grow away from the grain boundary into the matrix, but grows as a network of large thin dendrites in between the grains. IN austenitic stainless steels the carbon in supersaturated solution precipitates when the steel is heated in the temperature range 450" to 1000°C. During such heat treatments the chromium-rich carbide occurs primarily at the grain boundaries and has adverse effects on the corrosion resistance and low-temperature ductility of the material. It has been shown that the morphology of the precipitated particles differs widely depending on the time and temperature of the heat treatment, the nature of the boundary, the misfit between the grains, and so forth.1"5 It was assumed by Mahla et al.,&apos; Streicher,&apos; and Mc Nutt&apos; that the carbide particles which nucleate in the grain boundary grow in various geometric or dendritic forms away from the boundary into the matrix. However, Kinzel,&apos; Hatwell et a, and Plateau et aL4 found that the particles nucleate in the grain boundary and grow as a network of thin dendrites in the grain boundary interface. We have made a comprehensive studyg of the precipitation occurring in a commercial 302 austenitic stainless steel heat treated for times ranging from 0.15 to 1500 hr at various temperatures from 480" to 1065"~. This study was made to elucidate the influence of heat treatments on both the mechanical and the corrosion properties of this steel. Part of this investigation which is pertinent to the morphology of the grain boundary carbides referred to above is separately reported here. We found that the particles which nucleated in the boundaries grew in the interface of these boundaries, thus supporting the viewpoints of Kinzel,&apos; Hatwell et al.,3 and Plateau et al.4 Furthermore, when carbide particles nucleated in the matrix very close to the boundaries, they possessed a morphology distinctively different from the particles growing in the grain boundaries. MATERIAL A study of metallographic samples and of fracture surfaces of a 302 stainless steel is reported in this paper. The composition and heat treatments are listed in Table I. Polished and etched samples were examined und813r the optical microscope, and carbon extraction replicas of etched micrographic samples and various fracture surfaces3&apos;8&apos;9 were examined under the electron microscope. RESULTS AND DISCUSSION A representative optical micrograph of the 302 steel, condition A, is shown in Fig. l(a). Particles can be seen on the grain boundaries but no traces can be found of particles which grow from the grain boundaries into the matrix. A carbon extraction replica of this sample shows numerous large thin dendrites, Fig. l(b). The lateral dimension of such carbide particles vary up to 100 p, and their thickness estimated from the amoun! of electron penetration i:; between 500 and 1000A. Such large dendrites are extracted from almost all grain boundaries and, if they had grown into the grains, they would definitely be revealed by etching traces in the matrix, Fig. l(a). The reason why these large dendrites on the extraction replica appear to be grown into the grain is due to the mechanism of the extraction replica process. Thus, these dendrites are supported by the carbon replica film only at the edges originally along the grain boundary trace A-A, Fig. l(b), in the polished metal section and have subsequently fallen over onto the carbon replica film during handling. Although such dendrites generally fall only to one particular side of the grain boundary trace, one finds occasionally that parts of a dendrite have fallen to both sides, as shown in Fig. l(b). Further evidence for the growth of carbide in the grain boundary can be obtained from the appearance of fracture surfaces. A small impact specimen of the 302 steel, condition A, was broken at liquid nitrogen temperature. The fracture path follows the

Jan 1, 1962

By Sidney Katell

Philippine laterite and serpentine ores can be utilized in an electric furnace operation to produce both a steel ingot and a ferronickel product. Figure 1 is a schematic interpretation of a plant in which laterite and serpentine ores are processed separately to obtain both ferronickel and steel as products. A relationship of estimated capital requirements and probable returns has been established in this study for a plant of this type. No attempt has been made to evaluate the risks involved in commercial operations. At such time that the project might be constructed and placed in operation, changes in the costs of material, labor, and power may materially affect the profitability aspects of this study. One of the uncertainties involved in the economic evaluation is the cost of mining, handling, and shipping the ores. It is on this basis that the cost of ore delivered at the plant is assumed to be variable at $3, $5, and $7 per net ton (dry basis). For all other costs a plant site at Iligan City, Philip-pine Islands, has been assumed in preparing the economic characteristics for a plant that will process 2,000 tons4/ of ore per day. Results of the study, for the 2,000-ton plant, with all monetary values expressed in terms of United States currency (Philippine peso valued at $0.50), are summarized as follows:

Jan 1, 1962

A vigorous seismic and drilling programme has been conducted over.ar area of .59000 square miles in the Roma district during the last three years. The work is Mill&apos; in progress and although many new geological concepts have been discovered, he subsurface geology is not yet finalised. D.atailed examination has shown many variations of .section, has established the general basement trends and sedimentary thicknesses, has shown that much more of the section is marine than previously thought ~nd has indicated that any reservoirs throughout the section could be potential oil ind/or gas producers if suitable traps are located.

Jan 1, 1962

By W. A. Stickney, J. W. Town

Tests demonstrated that aqueous solutions of sodiu~n sulfide would dissolve over 95 pct of the cinnabal- in 5 pct Hg flrotation concentrates and 60 to 90 pct of the cinnabav in low-grade ol-es. Double-leach tests showed that potassiutn sulfide would dissolve 90 pct of the avsenic sulfide in Hg-As satnples and only 1 to 10 pct of the Hg; the sodium sulfide would then dissolve 80 to 90 pct of the rernaining Hg and 30 to 70 pct of the vemaining As. 1 HIS paper describes the extraction, by alkaline sulfide solutions, of mercury from cinnabar-bear ing ores and flotation concentrates. Leaching time and solution temperature had minor effects on mercury extraction when compared to the effects of reagent quantity and ore type and grade. Cinnabar, although readily soluble in sodium sulfide, was only partially soluble in potassium sulfide and essentially insoluble in ammonium sulfide. A double leach process was developed to extract selectively the arsenic from Hg-As products with K2S and to treat the residue with sodium sulfide-hydroxide solutions to extract the mercury.&apos; Mercury was then recovered from the pregnant solutions either by precipitation with metallic aluminum or by electrodeposition. The solubility of HgS in alkaline sulfide solutions was first reported by Volhard in 1878.&apos; The first reported commercial application was made in 1915 when Thornhill applied the method to the treatment of an amalgamation tailing.3 Mullhollen, in 1911. described the chemical reaction of HgS with Na,S and alkaline hydrate to be:4 Most investigators have reported using a 4-pct sodium sulfide and a 1-pct sodium hydroxide soluti~n.3-4 An increase in temperature or excessive dilution of the solution causes the reaction to be reversed. Church Holmes described a similar process used for the extraction of antimony from silver concentrates at the Sunshine Mining Company&apos;s mill at Kellogg. Idaho.5 More recently. Erspamer and Wells reported the results of leaching studies on a Hg-Sb ore from Alaska.6 EXPERIMENTAL PROCEDURE Leaching tests were made on samples of mercury ore from eight deposits in Oregon, Washington, and Idaho. In addition. tests were made on flotation concentrates from seven of the samples as well as a flotation concentrate from an operating mill. Since previous investigators reported reagent requirements greatly in excess of that required by the equation HgS + Na2S = HgS . Na2S, initial studies were made on chemically pure HgS. Results showed that the reaction actually required about 1 g of Na,S per g of HgS in an aqueous solution rather than 0.338 g of Na,S as indicated by the equation. To check further the matter of reagent requirements, Na2S and HgS were mixed together in equal mole ratios. Water was then added, a drop at a time, until the components reacted; X-ray diffraction analyses showed no HgS nor Na,S present. The yellow hydrate compound which formed would not redissolve until about three additional mole equivalents of Na,S were added to the solution. This indicated that a stable solution would require at least 4 moles of Na2S for each mole of HgS. While these implications may be valid for pure HgS, the possibility of entirely different results caused by the existence of other elements present in ores and concentrates was recognized. Consequently, experiments of the same order were made on samples of a flotation concentrate from a producing mill. The concentrate, containing about 18 pct

Jan 1, 1962

By D. V. Doane, G. A. Timmons, W. G. Scholz

Molybdenum of high purity can be produced by direct dissociatiott of commercial molyhdenm disulfide in vacuo at 1600° to 1700°C (2910° to 3090°F). The Product is lower in oxygen than commercially available molybdenzdm powder. Analyses of ingots arc-cast from commercial molybdenum powder, hydrogen-re-cluced from animonium molybdate, and from thermally dissociated molybdenum disulfide indicate that the levels of chemical impurities in these ingots are similar. Equipment now in operation will produce 100-lb hatches of powder product. The paper describes development of processing equipment, control of processing varzahles, handling of the product, and evaluatiotl of the melal produced. MOLYBDENITE (molybdenum disulfide) can be decomposed by heat in the absence of oxygen to produce elemental molybdenum and sulfur, which is evolved as a gas. The temperatures required for the dissociation are above 1370°C (2500°F); the sulfur must be continuously withdrawn to permit the reaction to proceed to completion. This is accomplished by continuous evacuation of the thermal dissociation chamber and condensation of the gaseous sulfur in another part of the system. Cognizance of the fact that the dissociation takes place in two steps is important in controlling the process. Basically, the molybdenite dissociation process has two potential advantages as a method of produc- ing pure molybdenum: 1) The materials entering into the process contain little or no oxygen. Since the process is carried out in vacuum at high temperature, the quantities of interstitial oxygen, nitrogen, and hydrogen in the product should be very low. 2) The process is more direct than the commercia1 method of producing high-purity molybdenum. In the conventional process, molybdenite is roasted to molybdic oxide, the oxide is purified first by sublimation, then by conversion to ammonium molybdate, and finally, the molybdate is reduced in a hydrogen atmosphere (usually in two steps) to the metal lic molybdenum powder. This paper presents a description of the stages in scaling-up of the dissociation equipment and an account of attempts to evaluate the molybdenum produced by thermal dissociation, rather than a report of a fundamental study of the dissociation reaction. Since little has been written on the subject, it is appropriate, before detailing the development of the process, to review briefly the research that has been conducted over quite a period of years. LITERATURE SURVEY The first accounts of the possibility of thermal dissociation of the mineral molybdenite were re-

Jan 1, 1962

By P. G. Shewmon, W. M. Robertson

The derivative of the surface tension with orientation, ??/??, for copper has been measured over the entire unit triangle. This derivative or torque term was determined from the variation of the dihedral angles at the intersection of twin boundaries and free surfaces. High-temperature anneals in graphite with a hydrogen atmosphere gave torque terms of 0.097 at (111), 0.066 at (100), and 0.0257 at (110). A variation from -36oto +23oC in the dew Point of the H2 had no effect on these values, nor did a change from 99.98 to 99.999 pct Pure copper. The removal of graphite from the system decreased ??/?? slightly. Considering the surface near a low-index plane to be smooth except for occasional steps, the free-energy increment per cm of step is calculated, and it is shown that the observed variation of ??/?? is consistent with a random distribution of steps and an interaction energy between steps. Integration of ??/?? gave the relative values of y at (100), (110), and (111) as comPared to ymax: (Y111/Ymax) =0.974, (Y110/Ymax) =0.996, (y100/Ymax) = 0.983. The ratio of the surface tension of coherent twin boundaries to the surface tension of the free surface was found to be (yT/ys) = 0.027 * 0.011. In a crystalline solid the surface tension y (surface free energy per unit area) depends on the orientation of the surface relative to the crystallographic axes of the crystal. Measurements of this variation of y with surface orientation have been reported for metals only within the last few years. Consider the grain boundary groove shown in Fig. 1. Here the three surfaces are all normal to the plane of the paper, and each has a different surface tension, y1, y2, and y3. If the system is at equilibrium, the total surface free energy must remain unchanged for a slight vertical displacement of the intersection (points A, B, and C are kept fixed). As shown by Herring,&apos; the following equation is obtained:

Jan 1, 1962

By E. W. Gieseke

Coal preparation men today are confronted with problems brought about by changing feed characteristics. The size consist of the coal going to preparation plants has been getting finer and finer. In order to handle these sizes economically, operators are turning to Notation. American Cyanamid Co., in an effort to enable coal flotation plants to produce efficiently at maximum quality and capacity, wnducted experiments which demonstrated that synthetic flocculants are useful for increasing the capacity of coal and refuse filters and for clarifying coal and refuse slurries, and a wetting agent is beneficial in reducing the moisture content of filter cake. Coal preparation men are today confronted with problems brought about by the changing coal markets, changing feed characteristics, and ever increasing labor and supply costs. Small mines are finding it difficult to exist, and the larger mines are rapidly converting to fully mechanized and automated operation to survive. The size consist of the coal going to preparation plants has been getting finer and finer, and the problems facing the preparation plant personnel are growing larger and larger. Facilities can be provided to handle this plant feed in new plants, but the problems are generally not so simple in existing plants where equipment must often be used to perform tasks far beyond its rated capacity. In addition, various state conservation departments, water commission boards, and other Federal and state agencies are endeavoring to eliminate stream pollution. These problems, and many more not mentioned, have been forced on the preparation engineer for reasons of economy and the public interest. In the matter of stream pollution, a determined effort is being made by the coal industry to cooperate with the Federal, state, and local agencies. Economists predict it will be necessary to produce 600 million to 700 million tons of coal by 1970. Bear in mind that the greater proportion of this increased tonnage will have to be processed in existing plants, and you get an idea as to the problems facing the preparation engineer. Methods presently in use for preparing fine coal do an acceptable job down to 48 to 100 mesh. A very large percentage of the - 48 or -100 mesh fraction of the tonnage of coal produced now is being sent to settling ponds or sold at a low figure for reason of quality. This has caused operators to turn to flotation. Building settling ponds and impounding fines is a costly and, at times, impossible method of handling these sizes. Recently a number of flotation plants have been installed to beneficiate material finer than 48 mesh, and these plants have demonstrated that flotation can be successful and increase the plant realization. Coal is a low cost commodity and processes for its beneficiation must be low in cost. Flotation is such a process. It is easily adapted to handling fine coal, requires very little supervision when properly installed, and is economical to operate. Flotation separates coal from refuse and fine clay. For reagents, several combinations are used. Some

Jan 1, 1962

By Nicholas J. Grant, Noboru Komatsu

Metallographic and X-ray studies were made of oxide dispersion strengthened Cu-12 vol pet SiO2 and Cu-3.5 vol pet Al2O3 alloys following time exposures at temperatures approaching the melting. point of the matrix metal. Changes in hardness, oxide particle size and crystal structure were studied to determine the time-temperature stability of these alloys. An interpretation of the mechanism of oxide agglomeration is proposed. One of the most striking features of dispersion strengthened metal-metal oxide alloys is their stability at elevated temperatures, both with respect to recrystallization and maintenance of mechanical properties after exposure at high temperatures. A small amount of work has been done on the re-crystallization phenomenon in dispersion hardened metal-metal oxide alloys&apos;l and several theoretical treatments have been advanced regarding the stability of these alloys by Lenel and Ansell,8 and by Grant and his co-workers.9, 10 This paper reports on metallographic and X-ray studies following various heat treatments of Cu-AI2D3 and Cu-SiO2 alloys at elevated temperatures and the effect of subsequent cold work on the recrystallizalion temperature. An interpretation of the recrystallization behavior of this type of alloy, based on the decomposition and agglomeration of oxides, is proposed. EXPERIMENTAL PROCEDURE Cast ingot bars of copper-1.59 pet Si and Cu-0.77 pet Al, 7/8 in in diam, were annealed in argon for 80 hr at 1000CC for homogenization. The homogenized rods were machined into fine chips and ball milled. Milled particles in the range minus 20 to plus 60 mesh were separated for internal oxidation. The internal oxidation was accomplished by the same method used by Preston and Grant,9 except that the oxidalion temperature for the Cu-Si alloy was 750°C, and for the Cu-A1 alloy was 800°C. These powders were then hydrogen-reduced at 450°C, compacted in a copper container, evacuated at room temperature to 0.04 µ, and sealed for extrusion. They were extruded at 1400°F (760°C) with a ram speed of 55 in. per min for an extrusion ratio of 15.6 to 1 to give a rod 0.38 in. diam by about 3 ft long.

Jan 1, 1962

By Robert L. Fleischer

A well known but unexplained experimental fact is the observation1 that aluminum shows a pure <111> wire texture, in contrast with other fcc metals, which have a mixed <100> <111> texture at moderate reductions. A possibly related single crystal observation on aluminum is the following:2 under tensile deformation <111> single crystals are stable (maintain their original axial orientation), while <100> crystals are unstable at room temperature and become stable at lower temperatures. This suggests that at room temperature, as proposed by Yen and Hibbard,3 the single <111> texture obtains be- cause <100> orientations are unstable in the poly-crystal. It also implies that for wire drawing at lower temperature a <100> component of the texture might be expected since that orientation is then stable. This possibility has been examined by wire drawing at temperatures near 77°K. The apparatus was designed to be used with an existing draw-bench, a steel trough acting as die holder and containing sufficient liquid nitrogen to immerse the wire entering the die. The trough is insulated by a styrofoam container to prevent excessive boiling of the bath. The wire emerging from the die enters a polyethylene tube, into the far end of which the grips are inserted. Liquid nitrogen is funneled into the tube to maintain the low tem-

Jan 1, 1962

By M. E. Tyrrell

Magnesia spinel (MgO.Al203) recovered from dusting slags in the system MgO.Al203-2Ca0.SiO2 is in the form of single crystals most of which will pass 35-mash. This investigation was undertaken by the Bureau of Mines to evaluate the concentrates as a refractory raw material. Three specific types of refractory bricks were studied: (1) dense, (2) lightweight bubble, and (3) insulating. Test specimens ware fabricated 1 by dry pressing, fired to 1,675° C., and tested by procedures common to the industry. The concentrates produced a refractor, having satisfactory density and mechanical strength; however, spinal is sensitive to thermal shock and the possibility of producing a spall-resistant brick using aggregate of such small grain-size must be considered remote. Lightweight refractorias fabricated of spinel bubbles were the most promising of the types tested. They were 30 percent lighter in sight than the dense refractory, their mechanical strength was good, and definite superiority in thermal shock resistance was indicated.

Jan 1, 1962

By Philip D. Anderson, Ralph Hultgren

Heat contents of extremely pure iron were measured over the range 300"to 1433"K, using a diphenyl ether calorimeter. Results from three samples containing widely differing impurities agreed with one another and with Previously reported results at higher temperatures (1184 ° to 1809°K) by Olette and Ferrier. From these data a table of heat contents of iron has been Prepared which is believed to be more accurate than those previously available. CP values have been derived which are consistent with these heat contents, with the best experimental Cp data, and with the thermodynamic conditions of equilibrium between bcc and fcc iron. The opinion is expressed that low-temperature extrapolations of presently known Cp values for y-Fe are not reliable. It would seem that the thermodynamic properties of iron, which is by far our most important metal, should have been well established long ago. This is not the case, however. As discussed by Olette and Ferrier,&apos; there is objection to every earlier heat content measurement. While the best true Cp determinations agree well at temperatures below the Curie point, there is wide divergence at higher temperatures. Several investigators have examined available data and attempted to calculate thermodynamic functions for iron that are consistent with the two equilibrium temperatures of bcc and fcc iron. The two primary efforts were those of Austin&apos; in 1930 and Darken and smith3 in 1948. The recommended values differ considerably; integration of Austin&apos;s Cp values leads to a heat content at 1100°K which is 300 cal per g-atom higher than the value recommended by Darken and Smith. The compilation of Fisher4 in 1949 was based on the selection of Austin. In 1956, Weiss and Tauer obtained yet another set of values by resolving Cp values into components due to dilation, lattice vibration, electronic excitation, and magnetism. The magnitude of contribution by each component and its dependence on temperature was estimated by semiempirical means. Their values are not self-consistent in that they do not form smooth curves when plotted vs temperature; moreover, their calculations cannot easily be repeated since they do not give the values of some of the parameters used. Clearly, experimental values for iron were in a most unsatisfactory state. The presently described measurements of the heat content of iron were therefore undertaken, covering temperatures as high as 1433°K. While the work was in progress, the high-temperature (1193" to 1789"K) heat content measurements of Olette and Ferrier&apos; were published; in the region of temperature overlap the present results agree with Olette and Ferrier well within experimental accuracy. It is believed that the present results, combined with those of Olette and Ferrier, provide for the first time a reliable set of heat contents of iron from room temperature to the melting point. From these data, guided by available Cp measurements, it proved possible to derive Cp, entropy, and free energy function values for @-iron from room temperature to the melting point, and for y- iron in the temperature region of its stability. Exhaustive study led to the conclusion that extrapolations of y-iron functions to room temperature were not reliable enough to be useful; hence these have been omitted from the tables. EXPERIMENTAL Materials. Three samples of extremely high purity iron from different sources, containing widely different impurities, were measured. The first of these, designated "Chipman", was kindly supplied by Dr. K. K. Kelley of the U. S. Bureau of Mines from a lot which was made many years ago by Dr. John Chipman of the Massachusetts Institute of Technology. The second, designated6&apos;Teddington", was supplied by the National Physical Laboratory, Teddington, England, from a lot zone-refined by them. The third sample, designated "Irsid", was supplied by the Institute de Recherches de la

Jan 1, 1962

By G. F. Dillion, A. F. Armington

THE present method for the ultrapurification of boron involves the formation, distillation, and decomposition of boron tribromide.&apos; However, the boron tribromide prepared contains several impurities in the ppm range, even after distillation. Some of these impurities, notably carbon, can be reduced after decomposition by zone refining. In this study, a comparison of the purity of boron tribromide at various formation temperatures is presented. The apparatus employed consisted of a bromine flask connected to a 22 mm ID horizontal quartz reaction tube packed with amorphous boron powder, which was in turn connected to a receiving flask cooled with an ice bath. Argon was used as a carrier gas. The approximate rate of passage of bromine to the reaction tube was 25 g per hr. The reaction was first investigated at several temperatures in order to determine the lowest temperature necessary to produce a colorless product which was assumed to be an indication of complete reaction of the bromine. The lowest temperature found in this study was 420oC. The amount of impurities found in the boron tribromide at various formation temperatures is shown in Table I. The data presented are emission spectroscopic results of boric oxide produced by the hydrolysis of 2 to 3 g of boron tribromide in 10 ml of distilled water. After hydrolysis, the samples were dried several hours on a hot plate. Assuming equilibrium conditions in the reactor, one can make approximate thermodynamic calculations estimatling the completeness of reaction of bromine with boron and its impurities at various temperatures. Data for these calculations were taken from Rossini,3 and must be taken as approximations since the T?S factor was not included in the calculations. The results of such calculations indicate that, with the exception of carbon bromina-tion, all impurities would react almost to completeness (> 99 pet) at all temperatures between 400" and 900oC. In the case of carbon, which cannot be accurately analyzed spectroscopically, it is estimated that only about one sixth as much carbon tetrabromide would be formed at 400" than at 900°C. Since some marked reductions in impurity content were observed at the lower reaction temperature which would not be predicted by thermo-

Jan 1, 1962

By A. Boltax

The effect of cold work on the electrical and magnetic properties of solution-treated and aged Cu-Fe alloys was studied. The electrical resistivity of solution-treated and of aged Cu-1.7 wt pct Fe samples increased by up to 25 and 140 pct, respectively, follozcing a 55 pct reduction of area. The principle contributions to the increase of resistivity of the solution-treated and aged samfiles are examined. Measurements of the .saturation induction, coercive force, and stacking fault Probability are also reported. 1 HIS paper is the second in a series which examine the behavior of the electrical and magnetic prop- erties of Cu-Fe alloys. The first paper1 was primarily concerned with the effects of thermal treatment whereas the present paper examines the effects of cold work on solution-treated and aged Cu-Fe alloys. The effects of cold work on the transformation of the coherent fcc iron precipitate to the ferromagnetic form2 and the coercive force and remanence3 have already been described, but the unusually large increases in resistivity (up to 220 pct) which occlir with cold work have not been reported previously. EXPERIMENTAL METHOD The methods used for alloy preparation, heat treatment, and electrical and magnetic measurements are described elsewhere.1 The specimens, initially 4-in. lengths of 0.0625-in. diam wire, were cold worked by swaging in hardened steel dies. Following each reduction, the samples were etched lightly in hydrochloric acid to remove surface con-

Jan 1, 1962

By M. L. Bowser

Pulse-forming circuitry is described for use in explosives research that requires precise synchronization and control of events in order to investigate detonation parameters. Included are pulse generators for oscilloscope sweep control, counterchronograph actuators, and a raster-type oscillographic method for the determination of velocities of detonation that are applicable to studies on solid, liquid, and gaseous detonations. INTRODUCTION Prom time to time, requests have been received for information on electronic circuitry used in explosives work at the Explosives Research Laboratory, Bruceton, Pa. The methods used are not entirely original;4 5 6 however, modifications of earlier techniques and some novel design aspects have resulted in time-tested methods that warrant a more detailed description.

Jan 1, 1962

By W. M. Dressel

A simple field test for detecting the presence of germanium in rocks, coals, and flue dust has been developed by the Bureau of Mines. The method consists of dissolving germanium from the samples by either acid or fusion treatment methods, adding a few drops of hematein or phenylfluorone dye, and extracting the resulting colored complex with carbon tetrachloride. INTRODUCTION Germanium is obtained commercially as a byproduct of zinc production, as a coproduct of base-metal refining from germanium-bearing mineral, and as a recovered product from the ash of some coals. The growing use of germanium in the electronics industry has increased demand for this semiconducting metal to the extent that an intensive search for new sources of supply is necessary.

Jan 1, 1962