Search Documents

By J. R. Nettle

The development of a process for upgrading offgrade titanium metal by electrorefining in molten salt led to an investigation of the electrotransfer characteristics of selected metals when alloyed with the titanium to be refined. Previous tests on seven binary titanium alloys showed that the degree of transfer of the alloying constituent depends on the constituent and on the operating procedurese.5 This report describes tests on electrorefining ternary mixtures of titanium with selected metallic elements. Ten alloys were prepared from high purity titanium and 2-1/2 percent of each of the metal pairs selected from the same elements used in the binary study; manganese, vanadium, chromium, zirconium, tin, molybdenum, aluminum. Operating variables were similar to those investigated in the binary alloy study that gave minimum alloy metal transfer. The data presented indicate the transfer characteristics of the various metals and combinations tested relative to each other.

Jan 1, 1962

By R. S. Wagner, W. G. Pfann

If an electric field is applied to a conducting liquid solution, changes in concentration usually occur because of differences in ionic mobilities. A variety of ways of utilizing this effect in conjunction with the freezing process are discussed in principle. For example, if a column of binary eutectic liquid is maintained a few degrees above the melting point and a field is applied, the component solid solutions will crystallize at opposite ends of the column until the liquid is consumed. An expression for the effective distribution coefficient, k, is derived for the case of a direct current Passing through a solid-liquid interface. It is shown that k can be varied It is well known that solute distributions in crystalline substances can be controlled by careful freezing from melt or solution. It is also well known that an electric field can produce substantial changes of concentration in liquid solutions by virtue of differences over a wide range, including values outside the usual range between ko (the equilibrium value) and unity. Hence, for many systems: the efficiency of zone refining can be increased; a ko of unity can be made greater or less than unity; solutes that lower or raise the fretzing point can be concentrated at the same end of the ingot by zone refining; be made equal to unity; and the tendency toward constitutional supercooling can be reduced. The methods of field-freezing are applicable to a wide range of materials including metals, semiconductors, and ionic conductors. in ionic mobility. In this paper we discuss, in principle, some methods that combine these techniques in useful way's. The methods are designated by the general term, field-freezing. Topics discussed include separation of the components of a eutectic, crystal growth, and controlling the value of the effective distribution coefficient. The methods are applicable to a broad range of materials, including alloys, semiconductors, fused salts, and other liquid electrolytes.

Jan 1, 1962

By A. M. Gaudin, T. P. Meloy

This paper presents the theoretical derivation of the distribution equation for single fracture. The equation is shown to accord with experiment. Several empirical size-distribution equations have been proposed to describe the size of broken materials. Among them are the Gaudin-Schuhmann equation and the Rosin-Rammler equation.3*4 The Gaudin-Schuhmann equation relates the relative fraction of undersize to relative size —. In this relationship Mo is the total weight of crushed sample, M(x) the weight of undersize contained, x the size considered, K a quantity called the size modulus, which together with the slope parameter, m, characterizes the product. The slope parameter is usually close to unity. The Rosin-Rammler equation relates the same relative fraction of undersize to the relative size modulus by an equation of different form In this relationship, e is the base of natural logarithms. In the fine size-range when m is unity both equations give Gilvarry and Berstrom have sought a size distribution equation having a sound theoretical basis. They have come to an equation taking into account the effect of volume, surface and edge flaws in fragmentation. If the effect of the volume and surface flaws is neglected, the equation taking only edge flaws into account has the form of the Rosin-Rammler equation. In the present paper, a theoretical size-distribution

Jan 1, 1962

By G. M. Yocom

Blowing acid Bessemer converters with oxygen-steam produces steel of below 0.002 pct N2 content. This method of blowing, combined with a dephosphorizing treatment in the steel ladle, results in low-carbon steels of low nitrogen and low phosphorous (under 0.035 pet) contents, which has physical properties equivalent to open-hearth steels of similar analysis. Using a 50-50 mixture of oxygen and steam, the refinitzg rate is increased 25 pct over blowing with natural air, and scrap charge increased from 3 to 10 pet. Bottom life is normal with proper tuyere area and arrangements, fumes are decreased, yields increased, and hydrogen content is normal. THE acid Bessemer plant at the South Works of Wheeling Steel Corp., consists of two 15-ton bottom blown converters with a monthly capacity of 57,000 N.T. The product of the shop is skelp billets for continuous welded pipe and slabs for ordinary drawing and forming quality sheets. Approximately 50 pct of ingot production is regular Bessemer steel of natural Phos content and the remainder is a dephosphorized grade of steel made by a special treatment of the blown metal as it is poured into the steel ladle. The low Phos grade of steel has certain advantages over the higher Phos grade but since both grades were produced by blowing natural air, the N2 content was in the range of 0.015 pct which limited its application. In 1954 it was decided to explore the possibilities of blowing with a steam-oxygen mixture for the production of steel of both low N2 and low Phos contents. The necessary equipment was installed to operate one converter in this manner and early in 1955 an experimental run of 160 heats was made by blowing with a steam-oxygen blast and excluding natural air entirely. During this period the proper operating techniques were established, such as blast pressures, steam-oxygen mixtures, valves and instrumental control equipment, tuyere arrangement in the bottoms, blowing times and production rates, and a thorough study made of the final steel quality. Also during this experimental period the dephosphorizing practice was improved by the use of a tap hole below the lip of the vessel. This provided a clean separation of the acid converter slag and blown metal which made the dephosphorizing treatment more effective. The results of this experimental run dictated further development of this practice and a second run of 720 heats was made in 1957. The quality features and conversion cost results were in line with expectations and accordingly a 400-ton per day oxygen plant is now being installed. The plant is scheduled for completion in September of this year. This will provide sufficient oxygen to operate both vessels on steam-oxygen blast and delete natural air blowing entirely. The steel will then be below 0.002 pct N2 bar content and the dephosphorized grades will be between 0.015 and 0.040 pct Phos. STEAM-OXYGEN BLOWING The steam for the process is fed to the plant at 220 psig pressure through a 6-in. line. The high-purity oxygen is compressed to 200 psig and conducted through an 8-in. line. The oxygen from the main line is valved down to 100 psig and passed through a steam heated heat exchanger. The heat exchanger is regulated to supply oxygen at 300°F to the steam-oxygen mixing station. It is essential that the incoming oxygen be held at this temperature to avoid condensation of the steam with resulting excessive erosion of the clay tuyeres in the vessel bottom. Oxygen is admitted to the mixing chamber by a 6-in. hydraulically operated valve driven by the ratio control regulator on impulse from the flow of steam. Steam is admitted to the steam-oxygen mixture station through a 2 1/2-in. hydraulically driven valve. The ratio control regulator acts to increase or decrease oxygen input as the steam flow increases or decreases with changing positions of the Blower's control lever. The important point to note here is that steam flow always precedes the oxygen flow as a safety measure. The control valves have sufficient capacity to afford protection should blow pipe trouble develop. A 50-50 mixture for these 15-ton heats demands an oxygen flow of 3800 standard cu ft per min along with 317 lb of steam. The Blower's stations is provided with an indicating blast pressure gage, and indicating steam and oxygen flow meters. Signal and warning lights indicate the valve positions and line pressures. A control room at the real of the Blower's pulpit room houses the ratio control and pressure regulators, as well as the various meter bodies. The hand actuated wheels used to change the conditions are mounted on a panel on the front of the meter control house. The recording steam and oxygen meters used for totalizing and accounting purposes are also mounted on this panel.

Jan 1, 1962

Titanium and Zirconium Industries Pty. Ltd. separates rutile and zircon from heavy mineral concentrate recovered from sand dunes on the east coast of North Stradbroke Island, Queensland. Separation plant feed is delivered to Dunwich, on the west coast, by a seven mile aerial ropeway traversing the island. Mining and concentration is effected by two floating dredge-concentrators now operating on the beach 31; miles from the aerial ropeway terminal. Heavy mineral concentrate is transported hydraulically from the dredges to the ropeway through a 6 in. pipeline. Six pumps in series deliver 24 ton/hr of dry solids in a pulp containing 13 per cent solids. For maximum economy the transfer pumping system is controlled deliberately to cause transportation in the zone of incipient settlement of solids, ieat velocities below the limit deposit velocity for the particular pipe diameter, pulp density, and specific gravity of solids. Automatic density control, based on a combination of power consumption and pipeline pressure, eliminates the danger of plugging the line but periodic flushing is necessary to remove gradual accumulation of solids in the bottom of the pipe. After 15 months operation the pipeline was descaled with hydrochloric acid to remove severe blistering with rust nodules, regrowth of which is now prevented by continuous injection of inhibitors. After transporting 100,000 tons of heavy mineral the average wear on the steel portion of the pipeline was 0·01 in. and indications are that wear on the asbestos cement portion is less.DESCRIPTION OF OPERATIONSGeographyTitanium & Zirconium Industries Pty. Ltd. (T.A.Z.I.) operates on North Stradbroke Island, some 30 miles southeast of Brisbane, Queensland. The island is approximately 25 miles long and eight miles wide, and is bounded on the east by the Pacific Ocean and on the west by Moreton Bay (Fig. 1). With the exception of a small outcrop of volcanic 1. Manuscript received at The Institute. 8th May. 1962. This paper was presented at the Annual Conference of The Institute. 5th-11th August. 1962.

Jan 1, 1962

By G. L. Hopps

Various chemicals, including compounds of copper and lead, were added to a mixture of No. 2 and No. 6 fuel oils that was fired in an experimental furnace. Tests were made to determine (1) the effectiveness of these chemicals in removing soot deposits on probes devised to simulate heat-transfer surfaces in boilers and (2) the effectiveness of the chemicals in preventing the deposition of soot on the probe surface. Test conditions were regulated so that the temperature of the products of combustion adjacent to the probes was in the range of 625° to 700° F. The clean-metal temperatures of the air-cooled probes were comparable with the water-tube temperatures in boilers operated at 40 to 100 p.s,i.g. The dosages of the fuel oil additives used in these tests were generally larger than those usually recommended for most proprietary compounds.

Jan 1, 1962

By R. W. Kraft

A comprehensive analysis of the crystallographic and metallographic structure of several Al-CuAl, lamellar eutectic grains solidified under equilibrium conditions has been performed. A consistent pattern was discovered which was interpreted in terms of a detailed atomistic model of an interface describable as: Interface II {111} AL 11 {211} <101>Al <120> ? Several arguments are presented to substantiate the theory. It is compared in detail with another interface model characteristic of the Wid-manstatten precipitate of CuAl2 in A1 at low Cu levels. In addition, a concept is proposed to help explain the structure of the compound CuAl2. It has been shown that the eutectic alloy between A1 and CuA1, can be forced to solidify as substantially parallel lamellae throughout a relatively large volume&apos; by appropriately controlling the solidification parameters of growth rate, thermal gradients, and impurity level and by causing solidification to proceed in a unidirectional fashion from one end of an ingot to the other. A typical ingot solidified in this manner shows three distinct zones along the length of the ingot, Fig. 1. At the head end is a region consisting of many different grains, some of which are elongated slightly in the direction of solidification. After a few centimeters of growth, this polygrained region gradually merges into the second zone which consists of a very few elongated coarse grains. The third zone at the tail end is a region of eutectic colonies caused by segregation of impurities. Microscopic examination of transverse and longitudinal sections of the ingots reveals that during the initial stages of growth (zone I) the lamellar structure is frequently highly distorted and twisted but that it straightens out in zone 11. This characteristic pattern suggests that nucleation of a eutectic grain begins randomly at the head end of the ingot, and that some particular orientation relationship between the phases is more favorable from an energy consideration than others for one reason or another, so that some grains grow and others which are less favorably oriented do not. The favorably oriented or "low energy" grains continue to grow until excess solute rejected at the advancing liquid-solid interface destroys the parallel lamellar structure by forming a cellular rather than a substantially planar interface. When this occurs, the parallel lamellae fan out and eutectic colonies are formed because the lamellae grow perpendicular to the local interface. Questions naturally arise as to the crystallographic nature of the "low energy" grains. What do the grains which persist into zone II have in common? Can this explain the stability of such grains during growth? To answer the first question it is necessary to determine the crystallographic orientation of the lamellae of each phase relative to one another. This has been done for Al-CuAl2 eutectic alloys by two different techniques on specimens prepared in different ways.2&apos;3 The results were different from each other and from a third orientation relationship between A1 and CuA1, reported for overaged A1-Cu alloys.4 The three orientation relationships are summarized below to illustrate their similarities and their differences. (001) ? 11 (001) A1; [l00] ? 11 [l00] Al Eutectic, Ref. 2 (001) 8 1) (001) A1; [1001 ?11 [1101 A1 Eutectic, Ref. 3 (001) ? 11 (001) A1; [l00] ? 11 [310] Al; Widmanstfitten, Ref. 4 It is not surprising that different orientation relationships were found by Ellwood and Bagley,&apos; and Takahashi3 since the solidification conditions were quite different. Nor is it surprising that Mehl, Barrett, and Rhines 4 found still another value since they were studying another type of alloy. Nevertheless, it would be expected that some logical and systematic pattern could be found if all the alloys were at equilibrium since the same two phases are

Jan 1, 1962

The conclusions reached by den Tex after a study of the fabric of some rocks from Broken Hill have been used to support the epigenetic hypothesis for the origin of the ore, first by Edwards (1959, p. 70) and then by Stillwell (1962, p. 131) in his criticism of Segnit&apos;s (1961) views. Den Tex claimed that the petrofabric study provided &quot;independent evidence that the ore, at least in its present form, post-dates all events of a diastrophic nature in the area concerned&quot;.Repetition of this claim by Edwards and by Stillwell and the lack of any criticism of den Tex&apos;s work for more than three years implies its general acceptance by geologists in Australia. Therefore it appears necessary to examine parts of den Tex&apos;s paper in detail to show that his, conclusions are unwarranted. The major weaknesses in his study are that1. the petrofabric study was inadequate to warrant any major conclusions, and2. the petrofabric data allow alternative conclusions.Den Tex made a single visit to the field, collected six carefully selected specimens and presented quartz and&#183; biotitepetrofabric diagrams for two specimens, quartz-diagrams alone for three more and included three diagrams of the orientation of c-axes and fractures in one specimen. It is not reasonable to come to firm conclusions about the origin of such a complex area as Broken Hill on such inadequate data, despite den Tex&apos;s claim (p. 87, lines 22 and 23) that &quot;a thorough investigation of the quartz-fabric of the wall rock was undertaken&quot;.Den Tex&apos;s interpretation of each diagram is open to criticism, and alternative (and to my mind, preferable) interpretations may be made. It is impossible to evaluate den...

Jan 1, 1962

By J. H. Brophy, J. Wulff, H. W. Hayden

The mickel-activated sintering of tungsten occurs in two stages of densification. A kinetic analysis of the second stage has been based on an appropriate model of the process. As in the first stage, the rate-controlling mechanism for the second stage is also the solution of tungsten in the nickel carrier phase. The transition from the relatively rapid first-stage results from the spherozdization of pores and the initiation of grain growth. Finer grain size due to higher-nickel content leads to more rapid and higher degrees of densification 1 HE sintering of tungsten is accelerated by small additions of nickel, cobalt, and iron.&apos; Experimental evidence in detail has shown that nickel-coated, hydrogen-reduced tungsten powder may be sintered to more than 90 pet of theoretical density at l100o C.2, 3 Simultaneously, a kinetic analysis of the process showed that it took place in two distinct stages. In the first stage, nickel evidently served as a carrier phase through which tungsten atoms could move. This stage was kinetically similar to the "solution-precipitation" step postulated when the carrier phase is a liquid,4 although in the Ni-W case, there is no evidence of the existence of a liquid phase either in equilibrium phase relationships or in microstruc-tures at the temperatures under consideration. It has been shown that this stage corresponds to a process which is rate controlled by a phase boundary reaction.3 More recent evidence has been presented5 showing that after the initial rapid stage of sintering, densification continues in the final stage but at a slower rate, although no mechanism for this stage of densification was defined. An analysis of later stages of densification in solid state sintering has been presented,6 but it is not directly applicable in the present case of activated or carrier phase sintering. It is the purpose of this investigation to study the final stage of nickel activated tungsten sintering in greater detail The effect of varying nickel content has been examined, and a possible kinetic mechanism defined. EXPERIMENTAL PROCEDURE AND RESULTS Commercial hydrogen-reduced tungsten powder from Wah-Chmg Corp., having a nominal particle size of1 µ and a B.E.T. specific surface area of 5500 sq. cm per g was mixed with aqueous solutions of hydrated nickel nitrate in proportions sufficient to produce nominal compositions of 0.25, 1, 3, and 5 wt pet Ni. This solution was then evaporated to dry-ness at approximately 150" C for 15 hr. Following evaporation, the resulting powder cake was broken with a mortar and pestle and reduced in hydrogen at 800oC for 1 hr. Following reduction, the powder

Jan 1, 1962

By H. R. Peiffer

The increase in electrical resistivity, ?pT,at 78°K was measured as a function of elongation, E, at 78°K for a 2 pct (approximately) by weight finely divided alumina in silver material. The amount of increase in electrical resistivity (?pT) is a function of the amount of alumina present and can be represented by: ?pT = cen where c and n are constants. The constant c increases and the exponent n decreases with increasing alumina content. Approximately 33 pct of the resistivity increase is recovered upon annealing at room temperature. RECENTLY, dispersed phase alloys&apos; have shown promise for use at elevated temperatures. These materials have a high creep resistance, a high-temperature strength considerably above that of the pure matrix, and a high electrical conductivity. These materials also show other properties such as retardation of re crystallization and resistance to flow even above the melting point of the matrix.&apos; It is believed that high-temperature creep is retarded in these materials because the dispersed phase blocks the motion of dislocations. According to schoeck3 and also Weertman,4 the rate controlling process is the climb of dislocations around the dispersed phase particles. Any mechanical property of these materials, or any other material for that matter, can be explained on the basis of defect structures and their interrelations. It would certainly be interesting to learn something about the effect of a dispersed phase on dislocation densities and also their effect on point defect concentrations following cold work. This is the purpose of the research discussed herein. The method used was the measurement of the electrical resistivity as a function of elongation at low temperatures. This scheme has already been applied to the studies of pure metals.5 Electrical resistivity measurements conducted on pure metals such as copper, silver, gold, and so forth, have indicated that defects such as vacancies and dislocations are formed during deformation.5 It has been shown by van Bueren6 that the resistivity change, ?p, should increase with elongation, E, according to the following relation: Ap=Al/2 + B£3/2 where A and B are constants of the system; ?p is in µ? cm. The first term refers to the amount of resistivity change associated with line defects and the second term with the change associated with point defects. A later calculation yielded exponents of 3/4 and 5/4, respectively.6 Manintveld7 has shown that the resistivity of copper increases with strain according to a 3/2 power law, whereas van Bueren has shown that the resistivity of silver increases according to a 5/4 power law. Assuming then that van Bueren&apos;s calculations are correct, it appears that line defects contribute very little to the electrical resistivity. There is some doubt, however, as to the validity of van Bueren&apos;s expressions for all cubic metals.&apos; In fact, the data on copper and silver are not conclusive. In this in-

Jan 1, 1962

By D. Kuhlmann-Wilsdorf

A new theory of work hardening is developed which rests on only a few simple principles and is applicable to a wide variety of materials and dislocation structures. It explains, qualitatively, the general characteristics of the three-stage shear stress-shear strain curve of fcc metals, as well as the most important features connected with easy glide. The value of, the work-hardening coefficient in stage 11, is derived quantitatively, from first principles, and is shown to be insensitive to many changes in detailed dislocation behavior. The low rate at which energy is stored during mechanical working in stage 11, the dependence of slip line length on stress, and the so-called Cottrell-Stokes law are explained. Although the theory is primarily developed for fcc metals and alloys, it is largely applicable also to some other materiuls, and in particular apparently to poly crystalline simple steels in theh linear range of hardening. FOR pure fcc metals and alloys, after many different pretreatments and under a great variety of testing conditions, the well-known three-stage work-hardening curve is commonly observed. Moreover, the work-hardening coefficient in stage 11, 011, bears an almost constant relationship to G, the modulus of rigidity, such that K = G/Brr" = 300, within a factor of about 2 either way. The very fact that the three-stage curve and the value of K are so very persistent, can hardly be understood except on the assumption that some quite simple phenomena are responsible. In this light all available theories of work hardening must be judged unsatisfactory: Each of them is based on some quite specific dislocation model, while it is known that metals with similar values of K may have widely different dislocation structures, for example, dislocation tangles in the case of pure fcc metals, and piled-up groups of dislocations in a-brasstype alloys. Thus, while a particular theory might conceivably represent a special case with a reasonable degree of accuracy, it cannot possibly have illuminated the underlying principle. Another severe criticism applying to the presently most widely discussed theories is that they employ empirical or even quite unexplained parameters in order to arrive at a numerical value of K. This indicates that some vital aspect of the work-hardening process has remained unexplained. In the present paper, a new theory of work-hardening is developed which does not suffer from the above shortcomings. It is derived from first principles, and is founded on the realization that the underlying causes for the three-stage work-harden- ing curve and for the persistence of the numerical value of O,, must be few and simple. As a first step it is shown herein that the experimental oklservations on "easy glide" can be explained on the assumption that in this stage dislocations multiply, beginning in a number of restricted area:;, and from there penetrate into crystal regions still substantially free of glide dislocations until a quasi-uniform dislocation distribution has been established. During "easy glide", the resistance to the movement of the foremost dislocations, advancing into still largely a dislocation-free regions, is believed to control the flow stress. This resistance is determined by various factors, among them the reaction of the dislocations against bowing-out into loops, which is due to their line tension. Without such bowing-out no dislocation multiplication would occur, but the corresponding contribution to the flow stress stays practically constant all through stage I. According to the present theory, stage TI begins as soon as there are no more areas left into which newly formed dislocations have not yet penetrated, i.e., as soon :is a quasi-uniform dislocation density has been attaned. Regardless of how, in detail, the dislocations should happen to be arranged at the end of "easy glide", whether in pileups or tangles, on one glide system or on several, the stress necessary to overcome the line tension of the segments must now increase, because the dislocation density increiises while the average free dislocation length decreases. It is argued that all other contributions to the flow stress stay at about the same level as in stage I, and that the said increase in the stress necessary to bow out dislocation segments into loops is responsible for the major part of work hardening in stage 11. Stage TII of the stress-strain curve is explained by largely follouing the ideas of Seeger and his co-workers; however, it is pointed out that the start of stage m may on occasion indicate the onset of "conservative climb" instead of cross slip. Indirect evidence indicates that linear work hardening persists even under the profuse action of cross slip, but at a lower rate. Only when, in addition to cross slip, climb operates extensively, does the work-hardening rat,. drop sharply, ultimately down to zero. BRIEF SURVEY OF EXPERIMENTAL EVIDENCE The stress-strain curve of crystals of many different substances are qualitatively similar. No significant permanent plastic deformation takes place below the so-called "critical resolved shear stress". As the applied stress is raised beyond this level. yielding occurs with little or no work hardening and

Jan 1, 1962

By R. E. Frounfelker, W. M. Hirthe

INVESTIGATORS in the areas of plasticity, crystal growth, and stress analysis have a need for crys-tallographic data such as the interplanar angles. This information is utilized in the form of a stereo-graphic projection from which orientation determinations can be made. Calculations of mechanical properties, such as the critical resolved shear stress, require values for the angles between directions as well as the interplanar angles. Only a limited amount of this data is available for tetragonal crystals. The equations for these angles are relatively simple but because of the large numbers of angles involved and the infinite number of structures that could be investigated, it was decided to program these calculations on a high speed digital computer. The angle, 8, between two crystal planes (h1 k1 l1)

Jan 1, 1962

By C. H. G. Bushell

The author maintains that selectivity in flotation depends in part on differences in rates of flotation. The rate of flotation should be directly proportional to the frequency of particle-bubble collisions. In this paper, it is suggested that floatable particles of the mineral must be distinguished from nonfloatable particles. Success in flotation is entirely a matter of selectivity. All minerals can be made to float. The problem is to make one mineral float and leave the others in the tails. For a typical ore, with all minerals naturally hydro-philic, a collector which is adsorbed by only one mineral and not at all by the others would give perfect separations. The hydrophobic, collector-coated mineral would separate cleanly from the remaining minerals. In practice, no such highly specific reagents are known. All standard collectors adsorb on most minerals to some extent, and selectivity then becomes a matter of extent of adsorption rather than adsorption on some minerals and not on others. Flotation is therefore a compromise process: if enough reagent is used to float all the desired mineral, the concentrate will be low grade; conversely, high grade concentrates can be attained only at low recovery. With many minerals coated with collector to varying degrees, selectivity appears to depend in part on each mineral floating at a different rate. The study of flotation kinetics is therefore a basic requirement to quantitative understanding of the process. REVIEW OF PREVIOUS THEORIES Before a particle enters the froth it must strike a bubble and adhere to it. Flotation rate will therefore depend on the number of particle-bubble collisions

Jan 1, 1962

By D. J. Brown

Froth flotation is now used to recover millions of tons of fine coal,(-1/2 mm), every year. For example, in Great Britain, 4-million tons of flotation concentrate was produced in 1960, about 3% of the mechanically cleaned out- put and 2% of the total salable output. Coal flotation is not so widely practiced in the U. S. as it is in Europe since much American coal occurs in thick seams of high grade and does not require cleaning. However, in the U. S., as elsewhere, the increasing mechanization of coal mining machinery has lead to a lowering in size and grade of product from the mine and to an increasing need for cleaning of coal to improve the grade before sale. With an increasing proportion of fines in the product, froth flotation has assumed a greater importance as a cleaning process for coal. In the last three years, over 40 flotation plants have been put into operation in the Appalachian area of the U. S.80 Fine coal recovered by means of froth flotation may be used as a powdered fuel alone or mixed with coarser grades. The removal of this fine coal from washery water makes possible the recirculation and re-use of the water and also leads to improved and more consistent operation of jigs and other separating machines which function less effectively when there is a build-up of fine solids in the washery water. Finally, froth flotation is of assistance in the production of a clarified effluent which may be discharged from the washery without polluting local rivers, streams, or wells. The 1961 cost of installing a new coal flotation plant in Great Britain would be about $19,000 per ton of dry solids input per hour, including the cost of new buildings and coal and shale filtration and water clarification equipment. The figure for the gravity concentration of the large coal, the main plant, would be about $4,800 per tph. The operating cost for the new coal flotation plant would be about $1.10 per ton. Even at this level of cost the cleaning operation is economic in Great Britain for coking coals. In the U. S., a froth flotation cost of 14$per ton of cleanfilter cake was quoted early in 1958 for one operation,l though admittedly this was a special case. Assuming a cake moisture con- tent of 30%, it is estimated that this cost is equivalent to a figure of 256 per ton of dry solids input, for the incorporation of coal flotation in an existing washery. A cost oh 416 per ton of concentrate was quoted76 in a recent analysis of flotation economics, this cost being brought up to $1.11 per ton after payment of royalty, welfare and association dues and taxes. Capital cost was $120,000 for a plant producing 133 tpd of concentrate. Before considering the treatment of coal by flotation it is appropriate to survey some of the properties of coal which are of importance in the process.

Jan 1, 1962

By Harry A. Lipsitt, Douglas Y. Wang

A fatigue study in completely reversed axial tension-compression has been perforried on high-purity titanium and on three high-purity alloys of titanium. The alloys each contain approxi7nately 0.75 at. pct of a single interstitial element; carbon, nitrogen, and oxygen, respectivley. The results corroborate a previously published theory which proposed that strain aging under alternating stress was responsible for the fatigue limit behavior of certain alloys. The present data indicate that in these alloys an increasing strain-talline aging effect under alternating stress is provided by oxygen, carbon, and nitrogen, respectively. CURRENT research on the nature of the fatigue limit in metals suggests that the presence of a fatigue limit in metallic materials is a manifestation of strain aging that occurs under alternating stress.lm5 A comprehensive theoretical model based on the above hypothesis has been developed to explain the existence of a fatigue limit.&apos; This model also provides increased insight into several other fatigue phenomena as under stressing, overstressing, and coaxing effects. The theory, as well, provides equal understanding for those cases where no real fatigue limit is observed. Briefly, this theory assumes that the S-N curve for a pure metal is a smooth function of the applied stress, and the effect of adding an element that is soluble (or forms a precipitate) in the pure metal is simply to shift the S-N curve to the right. If the added element confers the power to strain age, the result is a further shift of the S-N curve, this time upward and to the right. Since strain aging is not expected to be a strong function of stress, and since damage per cycle is known to be quite stress dependent, it is to be expected that there will be some limiting lower stress at which the strengthening due to strain aging will balance the damage due to crack propagation. This stress is the fatigue limit. The position of the fatigue-limit knee was thought to be a function of the magnitude of the strain-aging effect on both the finite and infinite life portions of the S-N curve. Although the strain aging hypothesis seems to be reasonably valid for bcc materials,2&apos;6 it needed to be tested for both fcc and cph metals. This report is the first of a series concerning the fatigue-limit behavior of titanium with varying amounts of the interstitial solutes (C, N,, and 4) that are known to cause static strain aging in titanium. Yield-point effects have been reported for polycrys-talline high-purity titanium alloys containing either carbon, nitrogen, or oxygen.7&apos;9 These effects were observed at testing temperatures in the range 100 to 300&apos;. In addition yield-point and strain-aging effects have been reported for single crystals of titanium containing 0.1 wt pct C plus N.&apos; These yield points were observed over a wide temperature range, but no room-temperature aging occurred. Aging at 180&apos; was required to cause the return of the yield point. The magnitude of the yield phenomena in titanium containing interstitials is not expected to be as large as is observed in bcc metals because of several factors. Titanium has a very high chemical affinity for oxygen and nitrogen. The thermodynamic stability of solutions of oxygen or nitrogen in titanium is recognized. Lattice parameter measurements of titanium containing arbon, oxygen,1° or nitrogen" show that the "c" parameter is expanded more than the "a" parameter, but that up to about 2 wt pct this results in an insignificant change of the axial ratio &apos;c/a." Ehrlich" has shown that the sites occupied by interstitial atoms in titanium are spherically symmetrical and therefore a lattice expansion, at a constant c/a ratio, results in a simple dilation of the interstitial site. Such a dilation involving no shear has been shown to react only with edge components of dislocations.13 This causes only a weak pinning action. Shear stresses would be anticipated locally when only one of the two interstitial positions was occupied. The carbon atom will cause a symmetrical distortion of the lattice whereas the oxygen and nitrogen atoms have, in addition, the previously mentioned chemical affinity of titanium for these elements. These factors will result in a considerably smaller reduction of free energy upon the association of interstitial atoms with dislocations, and therefore a much weaker pinning than has been observed for the bcc metals. These considerations would lead to the hypothesis that of the interstitial elements considered here carbon would cause the strongest pinning effect in titanium where the amount of interstitial in solution is constant. This hypothesis will be borne out in the analysis of the present results.

Jan 1, 1962

By R. A. Bosch, F. V. Lenel, G. S. Ansell

RECENTLY, Ansell and aenel&apos; proposed a dislocation model to account for the yielding behavior of dispersion-strengthened alloys. The criterion for yielding used in this model was that yielding occurs when the shear stress due to arrays of piled-up dislocations fractures or plastically deforms the dispersed second-phase particles. Calculations based on this model predict that the yield strength, uysof a dispersion-strengthened alloy containing particles whose geometry permits them to be considered as straight, i.e. not curved, barriers to dislocations follows the relation where and are the shear moduli of the matrix and dispersed phase respectively, b is the Burger vector of a dislocation in the matrix, A is the mean free path between dispersed phase particles and C is a constant. This yield stress, ys, is closely approximated in polycrystalline alloys by the proportional limit. The offset yield stress, uoy, is the yield stress, uys, plus the increase of stress due to strain hardening in the offset strain increment. Previous investigation1 has shown that Eq. [I] describes the yielding behavior of several different dispersion-strengthened alloys as a function of the mean free path between dispersed phase particles at a constant temperature. The purpose of this investigation was to investigate the temperature dependence of the yielding behavior of dispersion-strengthened alloys. The alloys studied, MD2100 and MD5100, are SAP-type alloys containing flake shaped aluminum oxide particles dispersed in a matrix of commercial purity aluminum. The proportional limit and 0.2 pct offset stress of both of these alloys were determined as a function of temperature over the temperature range from -190" to 500 C. All tests were conducted on an Instron tensile testing machine. Stress was measured by means of the Instron load cell. Strain was measured by means of SR-4 strain gages attached to the tensile specimens. Stress sensitivity was 80 psi. Strain sensitivity was 2 x 10F Fig. 1 shows the values received for the proportional limit and 0.2 pct offset yield stress plotted as a function of homologous temperature for both the MD2100 and MD5100 alloys. Inspection of Eq. [I] shows that of the terms which determine the theoretically predicted yield stress, uy,, only the shear moduli have an appreciable temperature dependence. From Eq. [I] the yield stress at any temperature T, UT, may be predicted from the yield stress at any arbitrary reference temperature, in this case 25 OC, u25, by the relation where the subscripts T and 25 refer to the values of the property at test temperature and at 25"C, respectively. The temperature dependence of the yield stress predicted by Eq. 121, based on the observed value for the proportional limit at 25OC, is also shown in Fig. 1. In evaluating Eq. [2] the following data was used. The values for the shear modulus of

Jan 1, 1962

By G. K. Lee, E. R. Mitchell

Designers of combustion processes may select aerodynamic conditions which produce only superfine fly ash. Although it is not usually anticipated that this will create a problem, such as has been found to agglomerate in high-velocity gas streams, to plug mechanical dust separators in a short time, and to contribute to atmospheric pollution. The problem is a fundamental one, and may be approached in several ways. The authors, in the course of their combustion research program, had occasion to examine the agglomeration of ash, ranging from sub-micron to 17 microns in size, produced in a (coal and oil) dual-fuel-fired steam generator. Several theories, supported by extensive laboratory studies, have provided some understanding of a probable mechanism of agglomeration. As a result, certain precautions are suggested in the design and selection of combustion processes and equipment.

Jan 1, 1962

By Z. E. Arlin, R. D. Lynn

A deep well injection system is used by The Anaconda Co. for the disposal of uranium mill tailing water near Grants, N. M. A 2511-ft hole was cored and tested through Triassic, Permian, and Pennsylvanian (?) sediments and bottomed in Precambrian granite gneiss. The disposal well was plugged back to 1830 ft and completed in 563 ft of sandstones in the Yeso formation. The reservoir sandstones contain water similar to the injected waste water, and are isolated from overlying fresh-water aquifers by an evaporite barrier zone. Mill tailing water is decanted, filtered, and introduced into the well by gravity at an average rate of 400 gpm. The reservoir has a life expectancy of 10 years. The Anaconda Co. began uranium milling operations near Grants, N. M. in 1953 with a small mill that processed limestone ores. A larger second mill was built in 1955 to treat sandstone ores. In 1956 it became apparent that a large tailing pond would be required to contain the increased discharge of mill waste water. Research was begun on supplementary methods of disposal by which a minimal pond size could be maintained to avert excessive seepage losses. An intensive sampling program was begun to monitor the fresh-water wells in the area. The original limestone mill ceased operation in 1959. The present mill treats sandstone ores by sulfuric acid leach and a resin-in-pulp ion exchange recovery circuit that uses chloride elution. Process waste water is discharged to a tailing pond where, after evaporation losses, an annual average of about 400 gpm are available for injection into the disposal well. The waste water is a mildly acid solution that contains large amounts of manganese, iron, and the sulfate and chloride salts of sodium, calcium, and magnesium. It is a low-level radioactive fluid that contains small amounts of Uranium-natural, Thorium-230, and Radium-226. The average chemical and radioactive analyses of the waste water injected into the disposal well are shown in Column B of Table I. Disposal of the excess mill waste water by deep well injection was investigated after extensive research had proved that alternate methods were not satisfactory. A study of the regional geology and hydrology indicated that a disposal well was feasible, and a test well to basement rock was planned. Tentative plans for the test well and the results of the geologic and hydrologic studies were submitted to the New Mexico Dept. of Public Health, the New Mexico State Engineer&apos;s Office, the U.S. Atomic

Jan 1, 1962

By R. I. Jaffee, F. C. Holden, H. R. Ogden

The effects of ternary and quaternary additions of aluminum, oxygen, and carbon on the mechanical properties of high-purity titanium-molybdenum alloys were studied for several microstructural conditions. Heat treatments were designed to produce 1) ß-quenched, 2) equiaxed ß) transformed (acicular) and 4) stabilized -P microstructures. Tension, impact, and hardness tests were performed. Transformations from the ß phase were followed by hardness measurements and metallography. The ß-to-w transformation was slowed by aluminum additions; carbon and oxygen additions increased the transformation rate. In addition to solid-solution strengthening, these solutes may increase or decrease strength by altering the /3 transformation kinetics. Aluminum additions promote the formation of strain-induced martensite, and lower yield strengths at compositions near 12 pct molybdenum.. a-P alloys are more ductile with equiaxed than with transformed microstructures. High strength levels can be reached by aging in many cases. Strength levels of the aged specimens usually are lowered slightly by straining prior to aging. ALLOYS of molybdenum with titanium form an iso-morphous alloy system which has been the subject of several investigations. Additions of substitu-tional and interstitial -stabilizing elements provide means of improving mechanical strength and con- trolling the heat-treatment response of the binary alloys. The work reported here forms a part of a continued study of the effects of microstructure on the mechanical properties of high-purity titanium alloys. Previous papers have considered the various binary alloys (Ti-Mo, Ti-Al, Ti-C, and Ti-0) that form the bases for the ternary and quaternary alloys included here. The compositions were selected to correspond with the previous binary alloys. Further, the high purity of the alloying components was maintained, so that direct comparisons with earlier work can be made. The total research program included a large number of compositional, microstructural, and testing variables. The data reported here have been selected to provide a reasonably complete and representative summary of the results. The reader is referred to the original Air Force Report for a complete tabulation of the results. EXPERIMENTAL PROCEDURES All the alloys used in this work were prepared from high-purity electrolytic titanium produced by the U.S. Bureau of Mines. A typical furnished analysis showed the following impurities in wt pct, balance This analysis is equivalent to that of iodide-refined titanium. In addition, hardness, tensile, and impact tests made using unalloyed electrolytic titanium showed it to have properties equivalent to those obtained with iodide titanium and suitable for these studies of high-purity base alloys.

Jan 1, 1962

By H. E. Rowen

I hope my title is not confusing; even more so that I am not. Actually pelletizing and sintering, meaning both the formation of pellets and the hardening of them, are closely related to each other and to phenomena of nature. Figure. 1 This many-celled porous structure, frozen as it was at the fusion temperature and was being frothed by fast-moving gases, may be considered a typical piece of sinter. The same structures have been found in natural ores.

Jan 1, 1962