Search Documents

By M. J. Saarivirta

A high-purity copper-zirconium alloy system was imesti-gated. The zirconium content of the alloys studied varied from 0.003 to 0.23 pet. The solid solubility of zirconium in copper and some physical and mechanical properties of the alloys have been determined. By proper heat treatment, Cu-Zr alloy can develop a high electrical conductivity and resistance to softening at temperatures up to 500°C (930°F). This combination of desirable properties makes this alloy superior, to other com-merzcrrl copper base alloys for- use in the electrical conductor field. DEMAND for high conductivity copper alloys that retain their mechanical properties at elevated temperatures is growing rapidly. At present, copper-base alloys such as copper-silver and copper-chromium are used where these characteristics are required. As an example, commutators in electric motors are often made of these alloys. However, the life at elevated temperature of commutators made of copper-silver alloys is much shorter than the life of the same part made of copper-chromium and copper-zirconium alloys. Copper-silver alloys are subject to creep and subsequent failure when the service temperature exceeds several hundred degrees centigrade. Use of copper-chromium alloys has been known for the past several years, but little information is available in the literature concerning the properties of alloys in the copper-zirconium alloy system. Some work had been directed toward determining the solubility of zirconium in copper as well as determining properties of the Cu-Zr alloys. These investigations have revealed the superior high-temperature and electrical conductivity properties of copper-zirconium alloys over copper-chromium alloys. The United States Metals Refining Co., Carteret, N. J. has recently produced OFHC R copper-zirconium alloys for experimentation and evaluation. Because OFHC R copper contains no appreciable oxygen, no harmful oxides are formed and the full benefit of Zr as an alloying addition is obtained. This paper describes the results of this work. It contains room-temperature and some high-temperature data which have been obtained after various processing techniaues. Actual elevated temperature properties are being determined and will be reported in a separate paper. Preliminary results obtained at elevated temperatures suggest that the Cu-Zr alloy is superior to other high conductivity copper-base alloys. WORK PROCEDURE The high-purity oxygen free (OFHC R) copper-zirconium alloys with zirconium content ranging from 0.003 to 0.23 pct were cast into 4-by 4-in. wirebars by both continuous casting and conventional casting methods. Zr was added in the form of a master alloy containing 30 pct Zr and 70 pct Cu. Castings were analyzed for zirconium and nine bars containing various amounts of zirconium were selected for this study. The results of analyses and the sample numbers are given in Table I. Typical analyses of OFHC R copper are also shown. The following properties were studied: A) Solid solubility of zirconium in copper. B) Effect of zirconium on properties of copper. C) Effect of combined working and heat treating on properties of Cu-Zr alloys. The solid solubility of zirconium in copper was determined by metallographic techniques. Specimens for this phase of the investigation were hot rolled at 900oC (1650oF) to 0.250-in. rod. The rolled rods were cut into 2/3-in. long specimens and solution annealed at 950 °C (1740°F), 980°C (1795 °F). and 1020 °C (1870 °F) for 6 hr and quenched in water. In order to find the solid solubility limits at lower temperatures, the homogenized specimens were reheated at various temperatures for 1 hr and quenched. The physical and mechanical properties were determined on 0.250 in. rod, 0.132- and 0.081-in. wires. The wires were cold drawn from the 0.250-in. rods after they were solution annealed at 980 °C (1795°F) and quenched in cold water. Mechanical and electrical properties were determined on cold drawn and

Jan 1, 1961

By C. S. Finney, John Mitchell

There is no field of human thought or endeavor which does not owe much to the past. Yet, surrounded by the prodigious scientific and technological achievements of our day, it is all too easy to forget the extent to which we have stood on the shoulders of giants. The coking industry of the United States is now a little more than one hundred years old. As with the American nation itself, the earliest beginnings of the industry owe a great deal to British influences, and its development owes much to those influences of continental Europe. No serious contribution to the history of coking in the United States can be written, therefore, which does not mention the work of the pioneers of the Old World. It is believed that the use of metallurgical coke dates back to antiquity. The fact that certain coals would soften under the influence of heat to yield a porous solid was known to the ancients of China and India, where a very crude coking operation was carried out by simply setting fire to piles of coal. After active combustion had started, turf or wet straw was used to seal off the pile. The coke obtained was used to forge iron and steel implements and weapons. Perhaps the earliest reference to the coking phenomenon is to be found in the writings of Theophrastus, pupil of Aristotle. In his History of Stones, which was written in or about the year 371 B.C., there appears the following observation. "But the Lipara stone empties itself, as it were, in burning and becomes like the pumice, changing at once both its colour and density; for before burning it is black, smooth and compact.... Certain stones there are about Tetras, in Sicily, which is over against Lipara, which empty themselves in the same manner in the fire." The first comparatively modern reference to coke is to be found in a recommendation for carbonization made in 1584 by Julius, Duke of Braunschweig-Luneberg, owner of the Hohenbuchen mine in the Harz district of Germany. In 1587, Sir Francis Willoughby of. Wollaton, England wrote: "There are twenty rooks broughte into charcoal and laid up in store." A rook of coal was equivalent to some 25 tons, and the coking would probably have been carried out in a manner similar, to that used for the production of charcoal. In 1589, Thomas Proctor attempted to carbonize coal, and in the year 1590 an English patent was granted to John Thornborough, Dean of York, in order that he might "purify pit coal and free it of its offensive smell". Sir Robert Cecil (1595), Robert Chantrell (1607), Simon Sturtevant (1611) and John Rovenzon (1613) were all granted patents for the use of coal or coke

Jan 1, 1961

By J. M. Weehuizen

Complete details are given of the drilling method by which two shafts were sunk at the new Beatm'x mine of Staatsmijnen in the Netherlands. The nature of the rock strata in the Dutch mining district determined choice of the drilling rather than the freezing method. Data for each step and details of the equipment used are given in the illustrations. Staatsmijnen was founded in 1902 with government financial backing, but it is run as a private enterprise, on a commercial basis, with the normal fiscal obligations. The company now has four mines in operation with annual outputs amounting to 7 1/2 million tons of coal. In 1952 it was determined that a new mine—the Beatrix—would be opened. Details of the shaft-sinking operation are described in this paper. SHAFT LOCATION The coal-bearing carboniferous rock in the Dutch mining district is overlain almost completely by soft water-bearing strata, which at the site of the new shafts are about 1600 ft thick. The sinking of the new shafts through this soft water-bearing overburden (Fig. 1) is a costly and time-consuming affair. From the two availaible sinking methods: 1) Poetsch's well known freezing method or 2) the drilling method of Honigmann-de Vooys, the latter was preferred, not only because of its relative cheapness, under the prevailing conditions, but primarily because by using the drilling process, a special type of shaft lining of steel, concrete, and bitumen could be used. The new shafts, located 330 ft apart, have an inner diameter of 18 ft, 4 1/2 in. The boreholes, which have a diameter of 25 ft and which were drilled through nearly 1600 ft of overburden and some 100 ft of carboniferous, each contain more than 29,000 cu yd—by far the largest in the world. DRILLING METHOD The drilling method is based on the use of mud-flush—a thin mixture of clay and water—to keep the borehole filled during the entire drilling period and during insertion of the lining (Fig. 2). The pressure of the mudflush against the borehole wall is greater than that of the water in the surrounding

Jan 1, 1961

By G H. Reavely, The University of Western Ontario Department of Geology

The lower Middle Devonian Sylvania Sandstone occurs in the sub-surface in the western part of Mal-den township, Essex county, Ontario. The formation is composed of well rounded, frosted quartz grains with a silica content varying from 42 to 93 per cent and the grains are cemented by carbonate, constituting up to 57 per cent of the rock. This sand-stone is not a homogeneous bed but is divided by strata rich in carbon-ate cement. The thickness of the Sylvania in Malden township varies up to a known maximum thickness of 88 feet. The lower contact with the chert-bearing Bois Blanc formation is sharp but the upper contact with the Amherstburg formation (Detroit River group) exists as a transition by a gradual downward increase in quartz grains. The Sylvania would seem to outcrop in the lake bottom near the mouth of the Detroit River dipping to the north along a broad anticline the axis of which follows the Detroit River. Just south of Amherstburg, a local east-west trending

Jan 1, 1961

By Leland A. Yerkes

Refining aluminum from crude aluminum alloys by the subhalide reaction was investigated to develop a method of producing aluminum by means other than electrolysis of its oxide. The best materials and design for the apparatus and also optimum operating conditions, including temperature, pressure, vapor flow rate, and composition of alloy charge were studied. In the subhalide process, aluminum-trihalide vapor reacts with aluminum in the alloy under high temperature and low pressure, forming volatile aluminum monohalide which reverts to aluminum metal and aluminum trihalide on cooling. The only halide used in this investigation was aluminum trichloride. The crude aluminum-silicon alloys used as the principal raw material contained from 21.9 to 36 percent aluminum, and significant quantities of iron and titanium. These alloys were produced by direct electric smelting of clays. Graphite tubing that was heated by an induction coil proved to be satisfactory material for the laboratory reactor chamber, Enclosed in an insulated glass or quartz pipe, the reactor was used in both vertical and horizontal positions with various baffle and tray arrangements for directing the trihalide vapor both over and through the alloy. Aluminum trichloride vapor was generated in the sublimer at one end of the glass pipe, passed into the reactor where contact was made with the crude alloy, and aluminum monochloride gas was formed. When the gaseous mixture of aluminum monochloride and unreacted tri-chloride passed out of the reactor and entered the condenser, the gases were cooled to 900° C. or less, causing the monochloride to disproportionate into aluminum and aluminum trichloride vapor. The aluminum was deposited on the condenser walls while the aluminum trichloride vapor was carried out of the condenser and into the opposite end of the glass pipe where it solidified on the cooled copper coils.

Jan 1, 1961

By Miles B. Royer

The experimental blast furnace has attracted increasing interest during the past decade as a practical means for investigating a broad range of blast-furnace smelting problems. Under experimental-furnace conditions, information can be obtained with less expenditure of time and raw materials and, therefore, at lower cost than comparable information could be obtained under industrial operating conditions. Furthermore, the experimental furnace may be operated beyond the range of smooth operation, even to failure, to delineate the limits of operability. Such deviation from normal operating practice would be economically intolerable in industrial operations where production and operating stability might be disrupted. The Federal Bureau of Mines experimental blast furnace at Bruceton, Pa., near Pittsburgh, has been operated and under development since 1951. However, the usefulness of this experimental data to industrial practice was somewhat nebulous in early experiments, and the correlation of the experimental blast furnace with the industrial blast furnace was not known.

Jan 1, 1961

Jan 1, 1961

By Charles W. Huggins

Electron diffraction and electron microscopy were used to determine the unit cell parameters of garnierite [(Ni,Mg)3 Si2O5 (OH)4] and to examine its crystal habit. Bundles of ribbons, many less than 200 A. in cross section, make up the bulk specimen of the garnierite Electron diffraction revealed the unit cell to be monoclinic. Unit cell parameters were: a, 5.33 A,; b, 9.23 A.; c, 14.96 A.; and ß, 94°441.

Jan 1, 1961

By M. E. Wadsworth, C. H. Pitt

Nickel corrosion in sulfuric acid solutions at elevated temperatures and oxygen wer-pressures was imestigated. Weight loss was 1inear with time and varied directly with oxygen concentration. Independent variation of the possible active species in solution indicated that the undissociated sulfuric acid molecule plays an important part in the corrosion mechanism. The rate determining step was considered to be the adsorption of oxygen on a site containing adsorbed H2SO4. THE tendency for a metal to go into solution depends on a number of factors some of which are: 1) the position of the metal in the electrochemical series; 2) the type and concentration of corroding species in solution; 3) the concentration of oxygen in solution; 4) the type of film formed at the liquid-metal interface; and 5) the physical state of the metal. The corrosion of a metal in an aqueous solution may be considered to be a heterogeneous reaction that occurs at the liquid-metal interface. The reaction is generally considered to occur as a result of electrochemical potential differences within the system. Little work has been published in the literature concerning the corrosion of pure nickel. A great deal has been publistled dealing with the experimental and theoretical aspects of the over-all corrosion process. Evans,1 Uhlig,' and recently Todt 3 and Tomashoff,4 have published books which review the results of experiments which have been conducted on corrosion, and have developed some of the basic ideas of the more widely accepted theories of corrosion. Friend5 states that. nickel does not readily discharge hydrogen from any of the common nonoxidiz-ing acids and that a supply of some oxidizing agent is necessary for appreciable rates of corrosion. He further notes that at temperatures between atmospheric and close to boiling, corrosion rates tend to vary with concentration, temperature, and aeration in acid concentrations up to 25 pct. Whitman and Russel6 studied the effect of dissolved oxygen on a number of metals in acid solutions and found that oxygen accelerates the rate of corrosion of nickel in sulfuric acid. Flowers and Kelley7 in studying the action of dissolved CO, on electroplated nickel postulated that nickel dissolves as NiHCO3 in the presence of CO, and air. It was found that oxygen was necessary for corrosion to take place and that the rate increased with increasing amounts of oxygen in solution. Flowers and Kelley attributed the oxygen effect to cathodic depolarization. MacGillavry, Rosenbaum, and wensson' determined metal solution potentials of nickel in various electrolytes. They found that nickel has no tendency to corrode in alkaline solutions in the presence or absence of air. In acid solutions in the presence of air, metal solution potential increases in the order of 1/2 v were observed. This increase was attributed to probable chemisorption of oxygen on the nickel surface and the corrosion mechanism suggested was the interaction of H+ ions with the nickel oxide formed at the surface. Delahay9 observed the reduction of oxygen on various metals. A polarograph was used to measure the course of the reaction. With some metals hydrogen peroxide was produced as an intermediate compound. However, nickel was not considered to be a hdrogen peroxide producer. Van Rysselberghe 10,11 and associates attributed the accelerating effect of carbon dioxide on the corrosion process to the presence of percarbonic acid produced in solution reacting with the hydrogen peroxide. The percarbonic acid can be reduced at less negative potentials than hydrogen peroxide and as a result accelerates the reaction. EXPERIMENTAL Since a complete description of the apparatus used can be obtained elsewhere,12'13 no attempt will be made here to describe the equipment other than to note that it consisted essentially of an autoclave unit from which samples could be withdrawn periodically without disturbing the interior state of the autoclave. A titanium autoclave liner was used to protect the autoclave from the solution.

Jan 1, 1961

By Nicholas J. Grant, Rolf Nordheim, Thomas B. King

Constant-load creep-rupture tests were conducted in an argon atmosphere at temperatures of 1600 to 2200°F on two heats of iron containing about 0.06 and 0.09 pct P in solid solution. The tests were conducted in the as-cast condition. Stresses were selected to give strain rates approaching those encountered in the hot working of steel, and within the limits of the creep-rupture test apparatus, namely. from about 0.001 to 50 pct per sec. FOR generations, rolling and forging practices have been developed largely by empirical methods, based on prior experience. While largely successful, difficulties are frequently encountered when new or different alloy compositions are tried for the first time. There is need to know the relationships which exist among temperature, strain rate, composition, and other variables on the deformation and fracture characteristics of steels. It has been shown for aluminum and several high-temperature alloys that the deformation and fracture characteristics follow rather well-defined laws and patterns which are closely related to the effects of strain rate, temperature, and composition.1"3 As the melting temperature of aluminum or its alloys was approached, it was possible to study the interplay of work-hardening factors and recovery or recrystal-lization, the latter resulting in improved ductility and increased resistance to intercrystalline fracture. In particular, the effects of composition are very poorly known. Within the meaning of "composition" should be included impurity elements, such as sulfur, phosphorous, lead, copper, and many others, as well as those elements which are added for alloying purposes in iron. The role of multiphase structures, in contrast to solid solutions, should also be studied in much greater detail. high strain rate creep-rupture tests would provide information regarding the deformation and fracture characteristics of metals at hot-working temperatures. It was also desired to establish the stresses which are necessary to accomplish the desired deformation, and to relate these to the strain rate and temperature. Secondly, it was the purpose of this particular study to determine the effects of phosphorus, within solid solution limits, on the deformation and fracture characteristics of iron at hot-working temperatures. EXPERIMENTAL PROCEDURE Two phosphorus levels were selected, one corresponding to the upper limit normally found for commercial steels, and one substantially higher than this, but within the region of solid solubility at the test temperatures chosen for this investigation. Twenty-pound heats were prepared by induction melting electrolytic iron in air in a magnesia lined furnace. After deoxidation with about 0.2 pct Al, ferro-phosphorus was added, and the heats were then poured into prefired silica molds. The purpose of using silica molds was to obtain a slow cooling rate during solidification to produce a relatively coarse grain size, producing a structure subject to some segregation and therefore more nearly characteristic of ingot structures. The major part of the casting assembly provided a large shrinkage head in order to produce sound castings and to promote slow cooling of the specimens. The primary austenitic grain size varied from ASTM No. 2 to No. 00. The composition of the heats, including a low phorphorus melt, used for comparison purposes, is shown in Table I. It will be noted that the oxygen content of the phosphorus containing heats is relatively high, in spite of the deoxidation practice, a condition which is difficult to control in small melts. Creep-rupture tests were nevertheless undertaken when it was noted that this quantity of oxygen did not appear to give results any different from those from a heat containing 0.01 pct 0, low phosphorus and comparable carbon Content;4 see Table 11.

Jan 1, 1961

By R. B. Porter, R. P. Porter, R. A. Lothrop

Changes became necessary in dredging methods employed in Idaho through passage of the Dredge Mining Protective Act (1954). Among other provisions, the law requires dredge operators to construct settling ponds of sufficient capacity and character to reasonably clarify the water used in the mining process before such water is discharged into the stream. Porter Bros. Corp., a placer mining company with many years operating experience in Oregon and Montana, became interested in strategic mineral placers in Idaho in 1950 when it was learned that prospectors had discovered a radioactive mineral deposit in Bear Valley Creek, 95 miles northeast of Boise. The company acquired mining leases and proceeded with exploration and development work on the property. After extensive research had resulted in the determination of successful separation processes, contracts were negotiated with the federal government and deliveries of columbium-tantalum and uranium concentrates commenced in 1956. The mining operations are located in a primitive area of Idaho among salmon spawning grounds and crystal-clear mountain trout streams. To avoid involvement in a very controversial issue, it appeared advisable for the company to develop water treatment procedures exceeding those requirements stated in the Idaho Dredge Mining Protective Act. Operation: The company operates one 6 cu ft continuous bucketline dredge and one 4 1/4 cu ft continuous bucketline dredge on the property. The dredges are jig-equipped, with feed being screened to 3 in. by trommels. The screening and gravity concentration methods satisfactorily separate the heavy minerals from companion clays, sand, and gravel. However, this separation of the heavy minerals requires water from the dredge pond with a minimum content of silt and colloids; therefore, water for dilution is added continuously to the dredge pond to suppress solids buildup. Discharge of this highly turbid water to maintain the proper pond level would ultimately result in an excessive silt load in Bear Valley Creek. To prohibit the turbid pond water from flowing directly into Bear Valley Creek, it was necessary to isolate the dredging area. Main by-pass canals were constructed along each side of the dredge pond and numerous secondary canals were dug for diverting seepage and snow runoff. One by-pass canal, extending more than two miles along the west side of the valley, diverts the main stream as well as tributaries entering from the west; a canal east of the dredge area diverts streams entering from that direction. At the beginning of operations in 1956, the dredge pond effluent was filtered through tailings and settled by use of coagulents in a series of lagoons. The filtrate was then discharged directly into the stream. Although this procedure gave satisfactory results in conformance with the state law, ice buildup and lagoon freezing hindered the efficiency of the process during periods of low temperature. For this reason, testing began in 1956 on a water treatment process that would operate efficiently under the extreme weather conditions encountered in Bear Valley. Development of Water Treatment System: Porter Bros. Corp. established the following requirements for effective continuous treatment of dredge pond effluent to the stream which, at low flow conditions, effluent to the stream which, at low flow conditions, would not result in a turbidity exceeding 25 ppm in the stream, 2) produce a sludge sufficiently dense to minimize disposal area requirements, 3) be semi-portable to follow dredge movements, 4) be capable of operating at low temperatures, and 5) be capable of handling a variety of capacities and turbidities.

Jan 1, 1961

The development of Mount Isa Mines Limited power supply is traced through the history of the mine operations. As would be expected, growth of the power supply system follows closely the increase in mine output, although it will be seen that total kWh. produced per ton milled shows a considerable reduction in later years when the mine output showed a more rapid rate of increase. That this reduction is not more marked is possibly due to the increased community and Shire Council power usage per head of population.INTRODUCTIONThe geographical position of Mount lsa, far from any large regional power supply Authority, dictated the policy that the Company be responsible for the production and suppiy of all power required for the plant operation. The Company also, in November 1937, accepted responsibility for the supply of a part of the power requirements of the township of Mount Isa. The history of power supply to the Mine may be divided into several phases.1. The supply Of lighting and power during the first plant construction period 1929-1931.2. The construction of the first section of the Mines Power Station, comprising Nos. 1 and 2 turbo alternators and boilers.3. The addition of No. 3 turbo alternator and boiler.4. The addition of No. 4 turbo alternator and boiler.5. The addition of No. 5 boiler.6. The addition of a. 2 turbo blowers for air supply to the Copper Smelter converters; b. 1 turbo blower for air supply to the L.ead Smelter; c. 2 turbo compressors for compressed air supply to the Mine and surface plant.

Jan 1, 1961

By L. A. Stewart

This is one of a series of reports prepared by the Federal Bureau of Mines on mining methods, performance, and costs at individual mines in the United States. The primary purpose of these papers is to promote development and conservation of our mineral resources by disseminating technological information on methods, practices, and results that may be applied to the engineering analysis and solution of mining problems. This report discusses the highly selective mining methods of the Jaquays Mining Corp. at the Regal asbestos mine, 45 road miles northeast of Globe, Ariz. The milling method at the Globe plant is discussed briefly, and the extraction ratios of the various grades of fiber are tabulated. The proposed flowsheet of a new mill under construction is shown.

Jan 1, 1961

By T. W. Wloder

During recent studies concerning the effects that various surface treatments, surface imperfections, locked-in residual stresses and metallurgical and geometrical notches have upon the mechanical behaviour of metals and, in particular, upon their tension-bending characteristics under impact loads, it became apparent that specially developed methods and samples would be of great assistance in determining the desired data. This paper describes and discusses a number of different types of double-notched tension-bending impact samples which have been considered and examined for this purpose. The types most suitable for exploratory investigations are proposed for application in the study of the _behaviour of metals, their welds, and, in particular, their surfaces, when subjected to various notch-severities, surface imperfections, strain rates, temperatures, and constrained states of stress (i.e. the relations of the three principal stresses). It is expected that the proposed double-notched tension-bending samples and the proposed test methods will also contribute toward further understanding of the cold brittle behaviour and the notch-sensitivities of metals. The possibilities of introducing the so-called impact notch-sensitivity index and relative impact notch sensitivity of metals are discussed. Data obtained on double-

Jan 1, 1961

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions5/ issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor and, if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1961

By S. E. Bronisz, J. O. Brittain

Experiments have been carried out to study the effect of an applied stress on strain aging in steel. It was found that the stress-induced strain aging reaction proceeds rapidly in the temperature range of 0° to 60°C. The variation of stress-induced strain aging with plastic strain, aging time, and temperatures is reported. The activation energy for the stress-induced strain aging was found to be 10,000 cal per mol for the steel used in this investigation. VARIOUS observations1-5 have been made of the influence of an applied stress upon the yielding of iron and steel. However, there have been only cursory studies of the effect of an applied tensile stress upon strain aging in iron and steel1,2 The following represents the results of a preliminary study of strain aging as influenced by the application of an external tensile load during the aging process. For the most part, previous experimental work on strain aging can be classified into two parts. First, the experimental technique involved a direct determination of mechanical properties of a suitable specimen that has been plastically deformed to a constant strain and aged generally at a temperature of the order of 200°C, with the aging times varying from about 1/10 to 2 hr.6-8 The second classification of strain aging experiments involves an indirect determination of strain aging by means of physical property such as electrical resistivity or internal friction as a function of the aging time at a constant temperature and strain.9-12 The latter results have

Jan 1, 1961

By H. J. Oberson, J. H. Brown

Comminution devices such as rod or ball mills are characteristically nonselective in their operation in that all material fed to a mill is ground to some extent. This is unfortunate when the object of comminution is liberation, for not only is energy expended in breaking pure gangue particles wasted, but, since gangue is frequently the predominant phase, the opportunity for such loss is great. Ideally, in this application a comminuting device should develop fracture only in locked particles. In the present investigation an attempt was made to use the large density difference which may exist between minerals to prevent comminution of one while grinding the other. EXPERIMENTAL MATERIALS AND EQUIPMENT The two minerals used in this work were -8-mesh galena and -8+ 20-mesh quartz. All tests were made on 2000-g charges containing 50 pct by weight of each mineral. Heavy media suspensions consisted of -100-mesh ferrosilicon in water. For grinding, a laboratory mill 10 in. diam by 12 in. long was filled to about 30 pct of its volume with either a ball or a rod charge. The balls ranged in size from 3/8 to 1 1/8 in. in diam; the rods ranged from 5/8 to 1 1/4 in. diam by 11 in. long. EXPERIMENTAL PROCEDURE In all tests employing heavy media, the ground pulps were treated as follows: 1) After recovering the ground charge from the mill but before drying, the pulp was wet screened on 200 mesh. 2) After drying the + 200-mesh product from step 1, the ferrosilicon was removed magnetically. 3) The nonmagnetic quartz and galena product from step 2 was sized on 10-mesh through 200-mesh screens. 4) The mineralogical composition of each screen fraction was determined by measuring its specific gravity. The specific gravity was related to the weight of galena in the fraction through the relationship

Jan 1, 1961

By N. H. Coates

As part of a joint program of the U.S. Atomic Energy Commission and the Federal Bureau of Mines for using nuclear energy to supply process heat, the Bureau designed and constructed a pilot-scale simulated nuclear reactor system. Although workable components were developed,5 the simulated nuclear reactor could not be operated continuously at its design conditions of 2,500°F. and 250 p.s.i.g. because the refractory materials used for insulation deteriorated. Replacement of these materials with porous carbon permitted sustained operation at design conditions, and a 1,000-hour demonstration run was completed successfully. No serious operating difficulties developed during the test. Leakage of helium after 1,000 hours was only 3 to 4 std. c.f.h. Inspection after the run revealed no damage to any of the components. Including earlier runs during previous research5 the system has been operated about 4,000 hours, of which 1,120 hours have been at 2,500° F. or higher. The helium-recycle compressor performed satisfactorily with no main¬tenance whatever for 2,445 hours, with about 2,000 hours at 900° to 1,000° F.

Jan 1, 1961

By H. M. Otte

Certain choices for the shear elements of the inhomogeneous distortion in the phenomenological theory of martensite formation are examined for their agreement with crystallographic and X-ray data of iron alloys. The assumption that the shear elements must represent slip or twinning systems characteristic of bcc metals is found to covey all observations, even when a small uniform dilatation is taken into consideration. In bct martensite, (011) becomes a possible twinning or faulting plane, in addition to {112), and qualitatively similar X-ray line broadening is to be expected from both. The basic concept inherent in the current theoriesl-4 of the formation of martensite is that the interface between the parent (austenitic) and product (martensitic) phase is an invariant strain plane (i.e., one that is undistorted and unrotated). Experimental evidence that the interface is of such a nature is available in certain transformations2'5'6 but for the transformation in iron alloys direct observation has not proved enlightening. Internal strains resulting from the formation of the small martensite platelets within the parent austenite matrix7 make it difficult to produce the desired evidence. Indirect evidence, however, such as the continuity of scratches in passing from untrans-formed to a transformed region, strongly indicates that the habit plane in iron alloys is an invariant strain interface. The scatter in habit planes in a given specimen8 would suggest that internal stresses have a slight but definite influence. On the other hand, composition changes which affect the lattice parameter can alter the habit plane appreciably, and by an amount greater than the scatter.' The success of the theories depends on the choice made for the "inhomogeneous distortion" or "complementary shear'' in the analysis and also on the choice for the parameter 6 representing a small uniform dilatation. In the approach developed by Wechsler, Lieberman, and Read'," it is implicitly assumed that 6 is unity. In the case of iron alloys, all observations cannot be explained without varying either the inhomogeneous distortion or 6 . Bowles and Mackenzie3 considered only the effect of varying d. They found it difficult to reconcile the wide scatter of habit planes with the theory and were forced to the conclusion that it may also be necessary to consider variations or different choices of the inhomogeneous distortion. Wechsler and Read" considered a limited number of possible choices for the inhomogeneous distortion, but no variation in 6, though this could easily have been introduced if so desired. It is the purpose of the

Jan 1, 1961

By J. S. Browning

The physical properties and specific gravity ranges of various liquids and salt solutions used for laboratory sink-float separations of rocks or minerals are presented. The test equipment and techniques employed by the Bureau of Mines in making sink-and-float separations of particles as coarse as 3 inches to as fine as 400 mesh are described. Also discussed are methods of recovering and reclaiming the liquids or salts from the minerals and wash solutions, as well as the hazards encountered and precautions to be followed while working with the materials. The laboratory use of various liquids for separating minerals of different specific gravities has been recognized for many years. During this time, laboratory sink-float procedures have proven their utility as a rapid and moderately accurate means for determining the mineral content of ores, test products, and plant products in certain nonmetallic concentrating operations, such as those producing mica, spodumene, kyanite, and so forth. These procedures also have been used as analytical tools for determining the mineral content and associations of other metallic and nonmetallic ores.

Jan 1, 1961