Search Documents

By J. H. Field

Synthesis of hydrocarbons by the Fischer-Tropsch reaction in a hot-gas- recycle system was demonstrated to be technically feasible. This project was undertaken, by the Bureau of Mines, to determine if the system was operable and to ascertain the optimum conditions for the production of gasoline. Carbon steel turnings packed with a void volume from 88 to 90 pct. were satisfactory catalysts, but steel catalysts with greater void volume, either turnings or steel wool, were not as active. Good temperature control with a pressure drop of less than 0.5 pounds per square inch (p.s,i,) per foot of catalyst bed of turnings was obtained by operating with a recycle to fresh feed ratio of 20 and by splitting the total gas flaw and injecting portions into the reactor at different entry ports.

Jan 1, 1961

By A. E. Bibb, F. W. Kunz

A platelet form of zirconium hydride was found in zirconium and ZY-1 wt pct U single crystals containing hydvogen in the range of 50 to 100 ppm. The habit planes for the hydride plateletg in the zirconium crystals were found to be {1012}, {1121}, and (1122) while the habit planes in the ZY-1 wt pct U crystals were {1121), {1123}, and (1.231). With the exception of the {1231} plane, these have been identified as the twin planes in zirconium. The different effect of hydridc on the mechanical puoperlies of zirconium at high and low strain rates has been explained in terms of the defornzation mechanism and the habit planes of the hydride. ZIRCONIUM and zirconium-base alloys are considered for many nuclear reactor applications, where the pick-up of hydrogen is a distinct possibility, if not an unavoidable occurrence. An excellent example of this is the absorption of hydrogen by zirconium and its alloys during aqueous corrosion, where as much as 30 pct of the hydrogen produced by the corrosion reaction is picked up by the metal. Under the proper conditions, the absorbed hydrogen would precipitate as zirconium hydride and consequently alter the mechanical and physical properties of the zirconium-base alloys. The knowledge obtained from a study of the crystallographic aspects of the hydride precipitation is necessary for the interpretation of the observed changes in the mechanical and physical properties. The deleterious effect of hydrogen on zirconium-base materials is not always observed in normal slow tensile loadings at or above room temperature, but becomes immediately obvious under impact loading, where the energy absorbed decreases with increasing hydrogen content,' and in notched specimens where triaxial loadings are attained.2 This effect is of serious consequence in the applications of Zr where shock loads or high strain rates are experienced. The purpose of this investigation was to determine the crystallographic planes of the Zr and Zr-1 wt pct U matrices upon which zirconium hydride will precipitate and to correlate these with the observed mechanical property data. PROCEDURE Crystal Growth—Single crystals of Zr and Zr-1 wt pct U alloy were used in this investigation. The Zr crystals were made from sponge that had a typical analysis as shown in Table I. Large grains were grown in this material by rapid cooling an arc-melted charge in a button furnace. This operation undoubtedly lowered the volatile impurity concentration below those listed in Table I. Back-reflection Laue patterns of these large grains showed the presence of considerable substructure and lattice distortion within each grain. It was found that an 18-day anneal in an argon atmosphere at 840°C (a high a heat-treatment) followed by furnace cooling, resulted in the further growth of the large grains and removed the detectable substructure ana lattice distortion. Equiaxed crystals with a cube edge of approximately 1/4 in. were produced in this manner. Large crystals of Zircaloy-2 (1.5 wt pct Sn, 0.15 wt pct Fe, 0.1 wt pct Cr, 0.05 wt pct Ni) also were produced by this technique but the large amount of substructure formed could not be removed by annealing. The Zr-1 wt pct U solid solution crystals were produced from an alloy rod consisting of Westing-house-Foote hafnium-free crystal bar zirconium and depleted uranium. The chemical analysis of the alloy is also given in Table I. Three-inch sections were cut from an 0.120-in.-diameter alloy rod and tapered to a fine point on each end. The samples were sealed in evacuated Vycor tubes, homogenized for 5 hr at 1000°C in the ß-phase field, and slowly lowered in a gradient furnace into the a phase (800°C), annealed for 60 hr at this temperature to produce grain growth and furnace cooled. This technique produced large grains approximately 1/2 to 3/4 in. long over the entire cross section of the rod, which were free of observable substructure. Metallographic examination up to X1000 did not show the existence of any second phase in these grains. Crystal Orientation—All crystals were abraded on fine emery paper to produce two flat surfaces 90 deg to each other. The crystals were analyzed by the standard Back-Reflection Laue technique to obtain the crystal orientation with respect to the abraded surfaces. The Back-Reflection Laue Photograms of all crystals used were clear and sharp indicating that the crystals were free from any substructure that could be detected by these means. Hydriding—Only samples containing four to five grains were used for hydriding. Samples that exhibited fine grained patches were discarded. The samples were hydrided using the following technique. After etching in 48 vol. pct HNO3, 48 vol. pct H2O, and 4 vol. pct HF (48 pct) solution, the specimens

Jan 1, 1961

By R. E. Ogilvie, N. L. Peterson

Intevdiffusion and intrinsic diffusiorz coefficients were determined in the uranium-niobium system from diffusion couples analyzed with an electron microbeam probe. A Previously unveported intermediate phase, designated in this report as the delta phase, was found to exist along the mobium-rich side of the miscibility gap. Its composition width was determined from the concentration gradients in the diffusion couples. The presence of this phase was also confirmed by microhardness analysis and metallographic observations. THE excellent corrosion resistant properties, high-temperature strength and reasonable nuclear properties of niobium have prompted its use as an alloying element with uranium and as a possible cladding material for reactor fuel elements. Hence the formation and growth of intermetallic phases as well as diffusion data for the uranium-niobium system are of considerable practical importance to metallurgists and nuclear engineers. Diffusion zones may exhibit varying degrees of complexity dependi.ng upon the mutual solubility of the metals involved, and the intermediate phases which may form. In the simplest case where the metals exhibit a calmplete range of solid solubility, a single phase region is produced. Generally, however, the metals may react to produce a multiphase diffusion zone containing several layers of intermetallic phases. A number of investigatorsl-6 have analyzed the concentration gradients present in diffusion couples in order to investigate phase equilibria and solu- bility limits. If diffusion is the rate-controlling process in establishing a concentration gradient, the compositions at the interfaces of the intermediate phases will represent the equilibrium values expected from the phase diagram at the temperature at which diffusion has taken place. No published information is available at this time on diffusion in the uranium-niobium system. A number of investigators7-" have contributed information to the construction of the uranium-niobium phase diagram from other than diffusion techniques. There is good agreement on the high uranium side of the phase diagram, but the high niobium side of the miscibility gap still remains somewhat in doubt. The phase diagram as determined by B. A. Rogers, et al.7 is shown in Fig. 1. The present work was aimed at obtaining fundamental information about the solubility limits of the miscibility gap and diffusion in the uranium-niobium system. A Kirkendall effect, which might be expected on the basis of the rather large difference in melting points between uranium (1132°C) and niobium (2415" C), was also investigated. The concentration gradients were measured by an electron microbeam probe technique, similar to that used by Castaing,l2 Adda and philibert,13, l4 and Macres.4

Jan 1, 1961

By B. H. Bergstram, C. L. Sollenberger

When glass spheres are crushed by slow compression loading, the outer lune-shaped fragments resulting from the fracture consistently fly outward at high velocity. About 45 pct of the strain energy fed into the sphere-platen system reappears in the form of the kinetic energy possessed by these fragments. These measurements were obtained from high-speed photographs. This kinetic energy can be utilized for addtional comminution if the fragments are allowed to impact against a suitable structure. Comminution theory has advanced considerably in recent years by the study of this unit operation under laboratory conditions. Some of the parameters have been isolated, but the experimental measurements of the pertinent quantities, such as energy, particle size, etc., are still only made prior to and after the conclusion of a fracture sequence. The catastrophic fracture process itself has not been adequately studied from a comminution point of view. It has recently been suggested by Gilvarry that the fragments which result from the free crushing of a single glass sphere by slow compression contain a considerable amount of kinetic energy after fracture. This kinetic energy, if properly directed, possibly can be partially utilized to cause additional fracture. In this paper a hypothesis will be presented which suggests that this kinetic energy is necessarily present and that its dissipation is the process by which a large part of the thermal energy imparted to the crushed product is generated. Evidence supporting the existence of kinetic energy and its utilization for secondary fracture will also be presented. THEORETICAL A previous paper4 has shown that the load-deformation curve of a system composed of an elastic sphere gripped by a pair of parallel platens, can be predicted by a consideration of the theories of Hertz as summarized by Timoshenko.' The deformation A, of one half of the system is given by which states that the deformation is a function of the mutually applied load, P, the radius of the sphere, R; and the respective physical properties of Poisson's ratio, v, and Young's modulus of elasticity, Y. The shape of experimental load-deformation curves conform to this relationship. The energy input to the sphere-platen system, can be predicted from the integral of the load acting through the appropriate distance, dA. Since dA can be evaluated in terms of P from the derivative of Eq. 1, this integral can be integrated between limits of 0 and P. The test sphere, however, is loaded at not one but at two points of contact, i.e., at both ends of a diameter, and hence the total energy input, E, is twice the energy input at each end, or The energy input to the system calculated from this equation corresponds to the energy computed from the measured area under the load-deformation curve. Timoshenko, considering the impact of two perfectly elastic spheres, has shown that the inter-penetration distance A is given by - m f (D (^ * ^t w as modified for the special case where one sphere is of infinite radius, i.e., its surface is a plane; where M is the mass of the finite sphere of radius R, and V is the velocity of approach at the start of an impact and also equals the final velocity of separation for perfectly elastic bodies. Because A is also a function of the load and the elastic properties, as shown in Eq. 1, the velocity, V, can also be calculated in terms of the elastic properties and maximum load, P, or

Jan 1, 1961

By Greaves M. C, Amos M. D

A study was made of the instrumentation and technique of atomic absorption spectroscopy developed by Walsh of the Commonwealth Scientific and Industrial Research Organisation (C.S.I.R.O.), Australia.The method was evaluated for the determination of silver in lead sulphide concentrate. The precision of the procedure developed is equal to that of the uncorrected fire assay method and the accuracy is greater.Brief mention is made of the use of this technique for the determination of silver and other elements in ores and concentrator products.INTRODUCTIONThe fire assay method, although accepted on a world-wide basis as the umpire method for the determination of silver in ores and concentrates, is freely recognized as yielding results which are lower than actual due to unavoidable losses.King (1934) investigated the influence of the cupelshape, size and material on silver losses during cupellation. Using 100 mg silver prills he recorded silver losses ranging between l. and 10 per cent under extreme conditions and averaging approximately 2 percent under conditions which might be considered normal. Guerin (1957) made a detailed study, under carefully controlled conditions in a furnace similar to that described by Esdaile (1952), of the effect of temperature on silver losses during cupellation. He concluded that if cupellation were carried out at 840°C., then the amount of lead retained by the silver prill was insignificant and that the silver losses were governed by the equation: Y = 0·055 XO.74where X = the final weight of the silver priIl (mg)and Y = the silver lost (mg)

Jan 1, 1961

By Perry G. Cotter

The borides of the transition metals in Groups IV and VI exhibit, in addition to a certain degree of hardness, considerable resistance to heat and oxidation. They have high melting points (1,850°-3,060° C.) and low coefftcients of thermal expansion and can be bonded with other materials and hot-pressed to desired shape (cermets). Suggested uses for the borides include use in rockets and jet engines, as thermocouple protection tubes, as containers for molten metals in die casting, as flame-plated coatings on less refractory compositions to prevent erosion by hot gases, and as control rods and neutron shielding material in nuclear engineering, The Federal Bureau of Mines investigation of zirconium diboride started in 1950 at the Boulder City Nev,, Metallurgy Research Laboratory, Its purpose was to reduce the cost of raw materials for the production of zirconium diboride.

Jan 1, 1961

In general, the metallurgical industry has so far been slower than the chemical industry to adopt ion exchange materials for industrial processes. The atomic energy industry presents a marked exception to this general situation, and the literature shows a rapidly increasing use of ion exchange techniques for the recovery of atomic energy metals on scales ranging from the ultra micro up to that of the largest mining operations. In many cases, the processes used would be equally applicable to more common metals and it is hoped that this review will be of interest to metallurgists outside the specialised atomic energy field. The review is intended to describe developments of ion exchange processes made during the last three years. Earlier studies have been summarised by Kunin and Preuss (1956) and Roland (1957). In order to restrict the number of references discussed, purely analytical procedures have been omitted and only those processes which have been conducted on a reasonably large scale or which, from their nature, areclearly capable of being upscaled, have been considered. The paper is divided into five main sections concerning respectively:Water treatment and effluent disposal.Metal recovery and purification.New ion exchange materials.New ion exchange equipment.Membrane cells.WATER TREATMENT AND EFFLUENT DISPOSALA high proportion of atomic reactors, and particularly those of American design, are cooled by water which is...

Jan 1, 1961

By Fred C. Bond

The perennial subject of comminution is deserving of a fresh approach if one can be found. This is attempted here by directing attention primarily to principles rather than to theories. While theories attempt to explain how a certain process acts, principles delineate the laws which the action-must follow. Comminution may be defined as the progressive separation of particulate matter. At the present time this is accomplished commercially by applying energy in the form of compressive and, shearing forces. Such forces strain and distort the particles they contact. When-the applied stress locally exceeds the breaking strength at the weakest flaw in the particle, a crack tip forms. The surrounding strain energy flows to the crack tip, which rapidly extends through the particle as a break. The minute changes in shape and the resulting energy flow cause the failure of other highly stressed flaws, with the consequent formation of a progeny (1) of new smaller particles out of its destroyed progenitor. The applied mechanical energy is transformed into strain energy as the particle is distorted, and then into heat when it fails. Only a tiny fraction of the order of 1/1000 of the applied energy necessary for breakage appears as new surface energy in the product particles. The comminution problem is the relationship between, energy input and product particle size. Its solution is of great-economic importance,

Jan 1, 1961

By D. A. Dukelow, G. Derge

THE Fe0-Mn0-Si0, system has many properties of fundamental interest besides its occurrence in steel-making. The system is the simplest ternary complication of the FeO-SiO, binary whose electrochemical properties have been explored. Therefore, knowledge of the conformance of Fe0-MnO-SiO, melts to Faraday&apos;s laws, as investigated by current efficiency measurements, would be of particular value in interpreting the observed variations of electrical conductivity, while at the same time furthering understanding of this type of molten oxides. Pertinent to the present study are conductivity data of FeO-SiO, and Fe0-Mn0-SiO2, and current efficiency data of FeO-SiO,. Concerning conductivity measurements, Inouye, Tomlinson, and chipman&apos; studied the specific conductivity, a, of molten wüstite as a function of temperature and oxide addition. Liquid FeO in equilibrium with an iron crucible was found to have a o whose magnitude and positive temperature coefficient were undeniably semiconductor in nature (o1400°C = 269 ohm-1cm-&apos;). Additions at 1400°C of 5 mole pct MnO decreased o to 227 while a similar addition of SiO2, dropped o to 125. Additional SiO2 produced an exponential decline of o. It was reasoned that because wüstite is known to be oxygen excess and since there is no pronounced change in oFeO upon melting, that UFeO(L)is p-type semiconduction. Björling2 gives o data for the ternary FeO-MnO-SiO, using fayalite, 2 FeO-SiO,, as the base substance. Upon addition of tephroite, 2 MnO-SiO, he noted a small decrease in o. Taking his data for 1400°C with one-half of the fayalite replaced by tephroite, o shows a decrease of some 40 pct relative to o for fayalite, i.e., 5 ohm-&apos; cm-&apos; to 3. In line with this observation, Mori and Matsushita3 reported that substituting MnO for FeO in the silicate de- creased o slightly except at high SiO, contents where the decrease was somewhat larger. Investigating the ionic nature of FeO-SiO2 melts, Simnad, Derge, and George4, found the anode current efficiency, C,, as calculated from iron anode weight loss, was temperature invariant and in general increased with SiO2 concentration. The authors suggested the possible presence of electronic conduction to explain why C+ < 100 pct. Fig. 4 includes their results as curve (b). EXPERIMENTAL METHOD Apparatus—Fig. 1 is a schematic section of the electrolysis cell used in all the current efficiency runs. The melt was contained in an iron crucible that rested on an alundum ring. A centered silica tube came within 1 in. of the surface of the melt and initially served as a thermocouple well and then as the guide for the anode.

Jan 1, 1961

By R. C. Emmett, D. A. Dahlstrom

Application of continuous filtration to precipitate dewatering requires not only careful equipment selection, choice of appropriate media, but also close control of precipitation technique itself.

Jan 1, 1961

By R. W. Van Dolah

An important function of stemming used to confine explosives in shot holes in underground coal mines is to minimize the chance of ignition of firedamp or coal dust by the detonation products. Until 1952, the Bureau of Mines approved only the use of fireclay or similar incombustible material for stemming permissible explosives. At least 2 feet of stemming were required except in holes less than 4 feet deep; in such short holes the stemming was required to be half the depth of the hole. Over the years, several special stemming devices have been proposed in the United States as substitutes for fireclay. Many economic and safety advantages were claimed for these devices, but only one approved device has been marketed in this country. Bureau requirements for stemming explosives in coal mines were modified at that time to permit the approved stemming device to be used as a substitute for the required fireclay.

Jan 1, 1961

By C. L. Klingman

In extracting helium from natural gas at Bureau of Mines helium plants, a continuous analysis of the helium content of inlet and outlet gas streams is required to determine extraction efficiency. An analyzer, using established principles of gas chromatography to effect the analysis, has been developed by the Bureau of Mines to meet this need. It will record the helium content of inlet or discharge gases from helium-extraction plants every five minutes, continuously, without the attendance of an operator. A 25-inch column of activated charcoal is used as a partitioning agent; nitrogen is the carrier gas; and a hot-wire, thermal-conductivity cell is the detector. A 1.0 mv, strip chart indicates the unbalance of the detector cell, Sample size is 0.37 cc, and carrier gas flow rate is 75 cc, per minute. Significant improvements in helium extraction have been demonstrated by using the chromatograph in three helium-extraction plants.

Jan 1, 1961

By Ruth F. Brinkley

This report is the 18th of a series of reports originally issued annually, and more recently bienially, to acquaint the public with the work of the Federal Bureau of Mines in explosives technology. Part I reviews briefly the overall activities during fiscal years 1957 and 1958.4/ Part II presents in abstract form the publications prepared by the Bureau that appeared during the period.5/

Jan 1, 1961

By Max J. Spendlove

The secondary copper industry is comprised of numerous enterprises which collectively employ many of the recovery and refining processes now used in primary plants as well as many other processes that are unique to the industry. Effective methods are used for identifying and segregating all types of scrap according to widely accepted standard classifications. Segregated scrap and waste materials usually require some preliminary processing to remove both valuable and deleterious associated constituents. Smelting, melting, alloying, and pyrorefining are common methods used for producing secondary metal, but operating techniques usually differ from primary metal operations because of the difference in physical and chemical properties of the respective raw materials. Some copper scrap is converted to copper chemicals rather than to refined metals or alloys. Recovery efficiencies of all processes are reasonably high, and the quality of products meets rigid specifications.

Jan 1, 1961

By Kenneth H. Johnston

Records show that waterflooding was tried in Osage County as early as 1934, but it was not economically important until a large unitized flood in the North Burbank field was begun in 1950. Development was rapid and by the end of 1960, there were 70 active water flood projects and 16 active pressure-maintenance projects in the County. The locations and status of the water-flood and pressure-maintenance projects in Osage County on December 31, 1960 are shown in figure 1, and information pertaining to these projects as of July 1, 1960 is given in table 1. For the past several years, Bureau of Mines petroleum engineers have arranged tours of selected waterflooding projects for the spring meeting of the Kansas-Oklahoma Water flood Association. These tours are conducted to demonstrate unique operating methods and new field equipment and to provide additional opportunities for exchanging information. Each of these tours has been supplemented by a published report describing in detail the projects visited. This report has been prepared for distribution during the 1961 spring tour of three waterflooding projects and a pressure-maintenance project in Osage County, Okla. (fig. 2).

Jan 1, 1961

By R. J. Brison, O. F. Tangel

The development of a new method of mineral separation was sponsored by the International Salt Company, which requested Battelle Institute to investigate means for improving the quality and appearance of rock salt from the Company&apos;s Detroit mine. Although developed specifically for removing impurities from rock salt, the general method may be applicable to other separation problems. The principal impurities in rock salt from the Detroit mine are dolomite and anhydrite which represent 2 to 5 pct of the weight of the mined salt. In the size range from 1/4 to M in. (the range of primary interest in this project) the impurities are only partially liberated from the halite in normal production. Further size reduction to improve the liberation of impurities is not practicable in view of the market requirements for the coarse grades of rock salt. Laboratory separations in heavy liquids showed that, to improve the quality and appearance of the rock salt substantially, it would be necessary to remove not only free gangue particles but also a large proportion of the locked-in particles. Because rock salt is an inexpensive commodity, a low-cost process was required. Gravity methods were, of course, considered. The heavy-liquid separations indicated that a split at an effective specific gravity of 2.2 to 2.3 would be required. (The specific gravity of pure halite is 2.16.) Heavy-media separation was investigated but had the disadvantages that it was necessary both to operate with saturated brine and to dry the cleaned salt, and that the cleaned salt was darkened by the magnetite medium. Air tabling was tried but did not give the desired separation. It soon became apparent that established methods would not provide a satisfactory solution and work was undertaken on the development of a new process to solve the problem. PROCESS DEVELOPMENT Preliminary Experiments: At the start of the investigation, an analysis of the problem indicated that the diathermacy of rock salt—that is, its ability to transmit radiant heat—might form the basis for an efficient separation process. Under this theory, the impurities might be selectively heated by radiant heat. The particles could then be fed over a belt coated with a heat-sensitive substance so that the warm impure particles would adhere preferentially to the coating. After the initial experiments, made by heating the rock salt with an infrared lamp and separating the product on small sheets of resin-coated rubber, proved encouraging, a small continuous separation unit was set up. This comprised 1) a simple heating unit consisting of a vibrating feeder covered with aluminum foil and an infrared lamp mounted above the feeder and 2) a separation belt 6 in. wide and 36 in. long. A sketch of the device is shown in Fig. 1. Results with this apparatus confirmed the fact that a good separation was possible. It was apparent, however, that a considerable amount of experimental work would be needed to develop the scheme to a practical and economical process. The Process: Basically, the process consists of two main steps: 1) selective heating by radiation and 2) separation of the heated particles on a heat-sensitive surface. Because neither of these steps had previously been utilized commercially in mineral processing, it was necessary to do basic research on both aspects. Factors studied in the investigation included type of heat source, design of heating unit, design of separation belt, selection of heat-sensitive coating, removal of heated particles from the belt, contact between particles and coating, and maintenance of the heat-sensitive surface. Part of the experimental work was carried out on a small-scale unit consisting of the 36x6 in. belt and auxiliary apparatus, and part on a larger unit. For simplicity, discussion of work on both of these units is grouped together. SELECTIVE HEATING Radiant-Heat Source: The essential requirements for a radiant-heat source were 1) that the radiant heat be in a wave length range which is effectively absorbed by the impurities but not absorbed appreciably by the rock salt and 2) that it be dependable, practical, and economical. Selection of a heat source of suitable wave length range was one of the first considerations. It is well known that pure halite is highly transparent to radiant energy in wave lengths from 0.3 to 13 microns. However, the available data on infrared transmission by dolomite and anhydrite, particularly in the range below two microns, were not complete enough to serve as a reliable basis for selection of a heat source. Although it may have been possible to obtain sufficient data on infrared transmission and absorption to enable one to select the best heat source, a more direct procedure was used. This consisted simply of exposing the crude rock salt to each of several types of radiant-heat source on the small continuous separation device. The heat sources investigated, approximate source temperature used, and calculated wave length of maximum radiation are tabulated in Table I. Of the two types of tungsten-filament lamps investigated, both the short wave length photoflood lamps and the longer wave length infrared lamps were satisfactory from the standpoint of selectivity

Jan 1, 1961

By E. H. T. Whitten

Fundamental principles of trend surface analysis are briefly reviewed. Recent analyses of several granite masses illustrate the method of estimating the quantitative regional composition and also variation trends. Mineralogi-cal, bulk chemical, and other quantitative variates can be employed. Such results should improve gravimetric surveys (etc.) relying on correction terms based upon estimated rock composition. For the first time realistic estimates of the mean composition of rock bodies can be made with the aid of trend components. Deviation maps hold promise for delimitation of disseminated mineralized areas. Deviations comprise residual "anomalies" after removal of trend components. In petrogenetic work such deviations have been shown to reflect local influences (e.g., contamination of magma by assimilation of xenoliths or country rocks of the envelope). Similarly, mineralization should be reflected as deviations standing out from background trends. Actual examples are given. Present results largely involved projection of data onto a horizontal plane, but if sufficient data are available use of three spatial coordinates increases accuracy for prediction in "unexposed" areas. Regression analysis shows that statistical correlations between variates for regionally distributed specimens are often strong (particularly with percentage data). Hence, in preliminary surveys more easily determined variates may sometimes be employed to gain first estimates of the distribution of components more economically significant. The sampling plan is of paramount importance. Unless a suitable sampling plan is devised and adhered to rigorously during collection of the samples, all subsequent analysis is liable to strong bias and to yield spurious estimates of the truth. For a wide variety of purposes it is becoming necessary to assess the quantitative composition and variability of rock masses and mineralized zones of various types. In petrology and petrography this is something of a break with tradition, because virtually all descriptions heretofore have been qualitative. Although vast amounts of qualitative data have been compiled, little is known about the quantitative behavior of rock components. However, if variability of rocks could be understood and expressed with sufficient accuracy, there would be considerable advantage to both economic and petrogenetic problems. For example, if, on the basis of a limited series of observations, the three-dimensional geometry of a disseminated orebody (or ore-bearing formation) could be predicted accurately, it would be possible to extrapolate with confidence the structure into unexposed areas. The following example based upon the geometry of an igneous cone sheet illustrates the point. The significant rock-unit gives outcrops at a number of points on the exposed surface ABCD (Fig. 1A). Study of n exposures may enable a geologist to predict that the rock-unit is circular in form and thus indicate where the unit can be expected in unexposed terrain. Such observations are made at sites with u, v coordinates, but, if subsurface information is available at sites with uvw coordinates, it will eventually become possible to predict accurately the three-dimensional form of the rock mass. Geologic rock masses or mineral deposits are not generally as regular and symmetrical in geometric form as the body illustrated in Fig. 1A. However, even where the broad limits of a major rock mass are known, a more acute problem arises in attempting to obtain detailed quantitative estimates of its internal variability; it is difficult to predict the variability of a mass from a limited number of observa-

Jan 1, 1961

By K. K. Kershner

This report describes an investigation by the Bureau of Mines designed to provide background data for extending and improving the applications of chlorine metallurgy in extracting metals from ores. Optimum conditions are given tor chloridizing galena, sphalerite, and chalcocite by contact with chlorine gas. Petrographic and chemical analyses of the sulfides used in the experiments are listed. Graphs are furnished showing the extent of chloridization of each metal sulfide over the temperature range of the observations. In each case, the first tests were made with the reaction chamber at room temperature. This temperature was increased by regular increments in succeeding tests until the temperature was reached at which quantitative conversion of the sulfide to chloride was observed. The data are also plotted for screen-size fractions of the sulfide minerals investigated. Data show that the extent of metal chloride formation was affected by chloridization time, particle size of the sample, and usually, the temperature of the reaction chamber. At 300° to 400° C. an anomaly was noted for both galena and sphalerite. The temperature at which this anomaly was observed varied according to the particle size of the mineral. Comparisons are made between the chloridizing characteristics of the mineral sulfides and their chemically prepared counterparts.

Jan 1, 1961

By Saint-Smith J. C

The anode, tank house and wire bar plant and operations are described with particular reference to those features of design and methods which are characteristic of this refinery at its inception.Reference is also made to auxiliary equipment, transport and materials handling facilities.The work of commissioning the plant late in 1959 is discussed and comment is made on the organisation of construction and origin of the equipment.LOCATION OF PLANTThe site chosen for the copper refinery is on level ground adjacent to the junction of the Mount Isa and the main north-south railway lines at Stuart near Townsville, Queensland. Blister for refining is received by rail from Mount Isa. Refined products are taken 10 miles by road to Townsville Harbour for shipment to other Australian ports or overseas, or despatched by rail direct from the plant.Adequate room for expansion was provided to cover copper refining and any associated industry. The layout of future extensions was planned and space reserved for them before detailing the original units of the main refinery.The initial plant also provides convenient storage facilities and is laid out to derive the greatest benefit from prevailing northerly breezes during the humid tropical summer.As far as possible, the working areas are located so that the prevailing winds cool them as they traverse the buildings.These factors are of very great importance since this is believed to be the only copper refinery in the tropics operating with all white labour and in any case the Company set out to provide the best possible conditions for its operating personnel.

Jan 1, 1961

Drill cores from Section 62, New Broken Hill Consolidated Ltd., were used to study the petrology of rocks associated with the zinc lode. The distribution of the rock types in relation to the lode structure was determined. The distribution of the gahnite-bearing rocks was shown to be only partly conformable with the structure.It was concluded that large scale metasomatism was not widespread, that the rocks associated with the lode (except, perhaps, the quartz-gahnite-garnet rocks) were formed by metamorphism of sediments, and that rocks and lode were contemporaneously metamorphosed.INTRODUCTIONThis investigation was undertaken in order to study the rock types associated with the zinc lode of the Broken Hill orebody, and their relationship to the structure of the ore horizons. The work was confined almost entirely to the laboratory, and is therefore limited in its scope. It is hoped, however, that the information gained may throw some new light on the genesis of the lode.Certain inferences which are drawn from this work are at variance with the ideas of a number of earlier workers.In particular, the idea of large scale metasomatism developing many of the rocks associated with the lode, especially those containing manganese, is questioned. On the contrary, the rocks associated with the lode are more simply explained as highly metamorphosed sediments, in some cases modified by water introduced from surrounding rocks into zones of strong folding and faulting. As a corollary, a metamorphicsedimentary origin for the lode material, either as a concentrated sulphide deposit, or somewhat disseminated...

Jan 1, 1961