Search Documents

By Henry J. Schwellenbach

Lack of a system in scheduling the replacement of capital equipment can result in emergency purchases of units which may later be found unsuitable for the job. New York Trap Rock Corp., which produces crushed stone for use as construction aggregate, was faced with just such a situation some years ago. The company replaced capital equipment only when machinery in use was no longer serviceable, or when there was an obvious need for different equipment. Operating and maintenance costs were generally neglected because an efficient method was lacking. New York Trap Rock has four plants located along the Hudson River, all within 70 miles of New York City. Crushed stone output-6 million tons a year-is moved to markets in metropolitan New York, New Jersey, and Long Island areas by water transport. Customers are contractors with ready-mix concrete and asphalt plants located on the water.

Jan 10, 1959

By J. M. Ohm, Carl M. Bunker

Two special tools for recovering gamma-ray probes and logging cable from drillholes have been designed by Ohm and Bunker and constructed by Ohm. Though intended specifically for U. S. Geological Survey equipment, they may be used with other equipment of the same general type. Fishing Tool for Probes: A fishing tool of the overshot type (Fig. 1) was designed to retrieve logging probes (sondes) that become disconnected from the logging cable and are trapped in the drillhole. When the tool slides over the top of the gamma-ray probe, studs on the bottom engage the shoulder near the top of the probe (Fig. 2), which is then pulled to surface.

Jan 10, 1959

By Lawrence Adler

Any design of a mine roof in bedded deposits which ignores differential deflections at the supports can quickly lead to dangerous overstressing. As illustrated by the typical case presented on page 1029, if one support deflects only 0.1 in. more than its neighbor, stresses 50 pct higher than anticipated will result. Previous studies1-3 have assumed that the mine roof acts like a beam clamped at both ends, with no deflection or slope4 at the supports (Fig. 1). Essentially this assumes:5,6 [BA = OD = 0 and dA = dB = 0.]

Jan 10, 1959

By Frank C. Frischknecht

Most early development and application of electromagnetic prospecting methods took place in Scandinavia, where geological conditions favor their use. In other parts of the world these methods have aroused cycles of interest, but in Scandinavia they have been used continuously and successfully since the 1920's. Electromagnetic methods may be classified into two general groups. One group includes methods in which the source of the electromagnetic field remains stationary while the receivers are moved about to explore the area. The other includes procedures in which the energizing and receiving systems are moved together. Other classifications could be based on the size of the energizing source, the particular components of the electromagnetic field which are measured, or the mode of trans- porting the equipment. The difference between fixed-source and moving-source methods, however, is of such great fundamental importance that it will be emphasized in this discussion.

Jan 9, 1959

By Walter L. Rice

It is a pleasure to report that the light metals industries are running well ahead of the growth schedule projected by the President's Materials Policy Commission. In the compilation of this survey on the five-year growth of our light metals industries, some gratifying facts come to light. By 1956, for instance, light metals consumption had increased more than 20 pct beyond Paley report expectations-a growth not anticipated by the study until the year 1960.

Jan 9, 1959

By T. Cantwell, N. C. Rasmussen, H. E. Hawkes

Beryl is a mineral that may be difficult to distinguish from quartz by casual field inspection. The easily recognized green color and hexagonal crystal form of coarse-grained beryl are by no means universal, even in beryl from pegmatitic deposits. If it occurred as a fine-grained accessory mineral in an igneous rock, it would almost certainly escape detection unless samples were submitted for petrographic or chemical analysis. There may be substantial deposits of some beryllium mineral, other than beryl, that has been overlooked because that mineral also closely resembles the common rock-forming minerals. A reliable and simple method of identifying beryllium minerals and determining the beryllium content of a rock would be helpful in exploration. This article describes preliminary experiments in applying nuclear reaction to the qualitative identification of beryl and to the semiquantitative determination of the beryllium content of rock samples.

Jan 9, 1959

By Wayne E. Hall

The Darwin mining district of California, 160 miles north of Los Angeles, has yielded an estimated $45 million in lead, silver, zinc, and copper since 1875. The deposits are in silicated limestone of Pennsylvanian and Permian age close to a stock of horn- blende-biotite-quartz monzonite. Steep left-lateral strike-slip faults that strike N 50" 70" E served as feeder channels for the ore solutions, and minor folds, favorable beds, and faults close to the feeder channels localized the orebodies. The orebodies are irregular, steep, pipe-like replacements that cut across bedding, bedding replacements, and fissure fillings in a calc-silicate country rock consisting mainly of wollastonite, grossularite-andradite garnet, idocrase, and diopside. Near surface the ore consists of a soft, crumbly mass of cerussite, hemimorphite, jarosite, limonite, and some secondary copper minerals. The primary ore consists of galena, sphalerite, pyrite, pyrrhotite, and chalcopyrite with smaller amounts of andorite, matildite, scheelite, tetrahedrite, and a high silver- lead-bismuth-selenium-bearing galena.

Jan 9, 1959

By John D. Kalasky

Continuous mining has revolutionized the coal industry but intensified the problems of earlier mechanization. From the installation of the first miner, it was recognized that face ventilation would be one of these problems. To establish an efficient work cycle for the equipment being used, conventional mechanized mining provides four or more development faces. Continuous mining, relying on a single machine, requires only one face, although more than one can be driven alternately by the same machine. In gaseous areas mined by the older methods, the intermittent rate of exposure allows time for the face to bleed off or be cleared, and the width obtained with conventional units makes it possible to hang a brattice line almost to the face. Continuous mining increases the ventilation hazards; there is no margin of time, and very limited space.

Jan 9, 1959

By Julian Nardi

Pumping solids through a pipeline is not new but until very recently other means of transportation were cheaper. Many proposed pipelines for transporting solids, while technically feasible, have not been attractive enough to warrant the financial risk involved. In some instances, the difference in transportation cost was negligible. In others, the threat of pipeline competition resulted in a slashing of rates on existing transportation to the point where a pipeline could no longer be justified. In others, a competitive product was cheaper. FIRST IN PLACERS The earliest record of solids being transported in a pipe was in the late 1850s in California placer mines. Water under pressure was used to force gold-bearing gravel up through a pipe, from 30 to as much as 55 ft, to a point where it could be discharged into a flume or sluice.

Jan 9, 1959

By E. M. MacKevett

The only source of uranium ore in Alaska that has been mined commercially is the Ross-Adams de- posit, a gently inclined, fusiform orebody in alkali granite in which uranothorite and uranoan thorianlte are the chief ore minerals. In mode of occurrence, apparent genetic association with the granite, and to a lesser extent in mineralogy, this type of deposit is uncommon. The mine is in the southern part of Prince of Wales Island (Fig. 1) at an altitude of about 950 ft on the southeast flank of Bokan Mountain. A steep unpaved road 1 ¾ miles long leads to the dock on the West Arm of Kendrick Bay, which can be reached by boat or seaplane from Ketchikan, some 35 miles to the northeast.

Jan 9, 1959

Scores of visitors who had never in their lives seen a piece of rough-and-ready mining machinery flocked around the display of Russian equipment presented as part of the Soviet Exhibition at New York's Coliseum. The Russian show, which ran from June 30 to August 10, presented an impressive view of an emerging technology. The exhibitors, however, made little attempt to appeal to the visitor who came only to be amused. In the mining show, as well as elsewhere throughout the exposition, the exhibits were devastatingly highbrow. If a coal mine's hydraulic roof support were "designed to support the prop- , free face front in longwall faces of flat seams, from 1.0 to 1.6 m thick, with medium-stable side rock," the visitors were told just that.

Jan 9, 1959

By Strathmore R. B. Cooke, Iwao Iwasaki, Hyung Sup Choi

Oleic acid is the chief ingredient of fatty acids used as collectors in nonsulfide flotation. With a few notable exceptions, the various quantities of saturated and other unsaturated acids comprising the remainder are usually unspecified. There have been occasional investigations to determine the collecting ability of these other acids and their effect on collection with oleic acid, but much remains to be done in this field. Hukki and Vartiainen, on the basis of tests using palmitic, oleic, and linoleic acids and an impure linolenic acid, concluded: "The collecting power of fatty acids used in flotation increases with increasing unsaturation of the hydrocarbon chain." 1 Their work was concerned mainly with the response of ilmenite to the foregoing collectors, although tests were also made with magnetite, pyrite, hematite, and rutile. Cooke and Nummela, employing an al- most identical technical procedure to evaluate flotation of hematite, magnetite, and goethite with various fatty acids, including oleic, linoleic, and linolenic acids of the highest purity obtainable, found: "The effectiveness of 18-carbon unsaturated fatty acids, as collectors for hematite, decreases with increase in the number of non-conjugated double bonds."' In the foregoing investigations, collector efficacy was measured on the basis of reagent addition in moles per liter.

Jan 9, 1959

By William G. Brissenden

Gaspe Copper Mines Ltd., a subsidiary of Noranda Mines Ltd., operates a completely integrated copper mining, milling and smelting plant at Murdochville, on the Gaspe Peninsula of Quebec. Operating six days a week, the mine produces 8000 tpd of ore. The mill runs continuously and capacity is rated at 6500 tpd of ore. Treating Gaspe concentrate output plus a certain amount of custom concentrate, the smelter produces between 3700 and 4000 tons of copper anodes per month.

Jan 9, 1959

By Robert J. Linney

Reserve Mining Co. produces 5 million tons of iron ore pellets per year. The finished product runs about 65.50 pct Fe, with 7.75 to 8.00 pct SiO2. Less than 12 pct arrives at the blast furnaces smaller than 3/8 in. This plant was originally designed to produce 3.75 tons annually-not 5 million. To handle the increased tonnage a fifth fine crushing line was added, and some very minor changes were made.

Jan 9, 1959

By William L. Payne, Edward E. Ives

A unique feature of Potash Co. of America's A new potash property near Saskatoon, Sask., is the use of semi-dome-shaped buildings for product storage. Four domed structures, timber-framed and corrugated-sheet covered, are being built; each designed to handle 20,000 cu yd. The relatively small capacity units, PCA believes, give flexibility not only in storing different grades and sizes of product, but also in permitting greater ease in shipping products as market demands change. The domed buildings are 150-ft diam, comprised of a 16-ft-high concrete wall base, topped with a metal sheet-covered octagonal timber frame. The dome of each unit is designed to fit very closely the angle of repose of the contained material, which results in the maximum usable volume. The entire roof is flood coated with a bitumin to provide a complete weather seal.

Jan 9, 1959

By John Sullivan

Resources for Freedom, a report by the President's Materials Policy Commission, commonly termed either the Paley report, after its chairman, or the PMPC report, was issued in June 1952. The data collecting and assembly work for its preparation were done in 1951. The statistical base in most cases was 1950. It reviewed our economy and predicted what it will be in 1975.* The bases for the predictions were given. Consideration was given not only to statistical data and trends but also to technological changes taking place and likely to take place in the ensuing 25 years that will affect our economy. The supply of raw materials was studied and predictions made as to the availability of supply and the sources in 1975. One of the industries covered was iron and steel. For the most part the report did not attempt to provide a curve showing annual growth for any industry or commodity. It contrasted 1950 with the probable status in 1975. Interpolation between these dates is difficult and the Commission did not intend that it be used for short interim intervals. It is possible in 1958 to show the actual changes from 1950. The magnitude of the changes illustrates the agreement with some interpolation of the Paley report. Statistical comparisons can be general only because the Commission did not postulate a linear change. A study of the iron and steel industry will show if the general predictions have been realized or if gross errors were made. This paper is concerned with such an analysis. It is concerned with the production and consumption of crude, not fabricated products. It attempts to bring various facets of technical and statistical information on the industry up to date.

Jan 8, 1959

A fast, easy, and inexpensive method of determining the consolidation of overburden in surface mining operations through seismic analysis has been developed. The method involves use of a refraction seismograph which measures overall consolidation of subsurface materials, including such factors as rock hardness, stratification or lamination, fracturing or jointing, and the degree of weathering or decomposition. It also is possible to determine the thickness of various layers of subsurface materials to depths exceeding 100 ft.

Jan 8, 1959

By G. M. T. Marshall

Plans to bring the Geco Mines property in Manitouwadge, Ont., into production began in 1954. At that time over 12 million tons of copper-zinc ore were indicated in a zone 2700 ft long. A concentrating plant was built to handle 3300 tpd of ore and a production shaft was sunk about 1500 ft. MINE LAYOUT Vertical attitude, width, rake, and competent country rock of a 4-million ton orebody west of the main diabase dike suggested a system of blasthole stopes, undercut with scram drifts connected by a transfer raise system to a crusher on the 1250-ft level and this system was employed. A 42-in. conveyor on this level transfers the ore about 1200 ft to a loading pocket at the No. 1 shaft. The system has a number of advantages: 1) Cost of tramming is eliminated. 2) Rate of extraction from any stope is controlled only by the scraping capacity of the scram. 3) Rate of extraction from the stoping area can be very rapid. Fast extraction makes it possible to cut mining costs for the following reasons: The number of stopes actively producing is kept to an economical minimum; the operating area is concentrated-manpower can be used more effectively; and active life of the stoping block is short, making ground support problems simpler and less costly.

Jan 8, 1959

By Waldemar F. Dietrich

Mineral fillers are relatively inert chemically under the conditions of use but have physical properties* that modify those of the materials in which they are incorporated. The mineral fillers considered in this article are asbestos, barite, clays, diatomite, crushed limestone, limestone whiting and lime, mica, silica, talc and soapstone, and pyrophyllite. Slate and stone, other than limestone and its derivatives, are excluded because, even though used in large quantities, they are exceptionally low-cost materials generally produced close to the area where they are used.

Jan 8, 1959

By Benjamin N. Webber

During World War II the Pocos de Caldas bauxite deposits of Minas Gerais in Brazil yielded some 60,000 tons. Since then they have maintained a small but almost continuous production. Known for many years, the deposits have been reconnoitered by a number of geologists,1-4 but no dimensional study has been possible because there have not been enough exposures to show clearly the depth, bedrock, and habit of occurrence. The deposits are somewhat unorthodox in their occurrence mainly on steep slopes of mountainous terrain. Although the parent rocks are a sequence of alkalic intrusions that bauxitize readily under the proper conditions, bauxitization has not been the dominant weathering process in the area. It is limited to certain localities where important volumes of bauxite have formed by laterization of several rock types, each yielding a distinctive type of bauxite. Bauxitization may be observed in several stages and in both direct and indirect cycles of formation. The deposits are unique in being of demonstrably recent age, so that the conditions under which the bauxite formed are essentially those of the present time. The bauxitization sequence is postulated in Fig. 1.

Jan 8, 1959