Search Documents

By W. M. Parris, P. D. Frost, H. A. Robinson

The effects of hydrogen content and strain rate on the static tensile and notch-rupture properties of the Ti-3Mn-complex alloy heat-treated to differed strength levels were investigated. The extent of embriulement was found to be proportional to the amount of hydrogen present and the strength to which the specimens were heat-treated. The research suggests the possible necessity of specifying lower hydrogen limits than are now allowed when titanium alloys are heat-treated to higher strengths than are presently used. The research also supports a hypothesis advanced earlier for a mechanism of hydrogen embrittlement. MUCH attention has been focused on the effects of hydrogen in in Most of the published in- formation has dealt with the effects of hydrogen on alloys in the annealed or lowest-strength condition. The work of Kotfila and Erbin3 is one of the few exceptions. In view of the fact that heat-treatments are now being used to produce high strength in titanium alloys,' it is necessary that more attention be given to the effects of hydrogen on these alloys in the heat-treated condition. Research was initiated to establish the effects of hydrogen on the properties of the Ti-3Mn-complex alloy at various strength levels. This research, which supplemented that of Kotfila and Erbin, was started because it was found that high-strength tensile specimens of this alloy were strain-rate sensitive. The essential results of the research are summarized in this paper. MATERIALS AND EXPERIMENTAL PROCEDURES Material for this investigation was a 41/2-in.-diam bar forged from a single commercial heat of the Ti-3Mn-complex alloy having the composition given in Table I. The as-received forging was reduced further by forging at 1750°F to 3/4-in. square bars. About one fourth of this material was vacuum annealed at 1400°F for 24 hr to obtain a base hydrogen content of 25 ppm. The remaining bars were hydrogenated to levels of 90, 140, and 260 ppm in a large Sievert's apparatus in the following manner: Four 3/4-in. square bars, 5 in. long, were placed in the reaction chambzr. The chamber was evacuated, heated to 1400°F, and a measured amount of hydrogen was introduced. When absorbtion was complete, as indicated by the drop in pressure, the reaction tube was cooled and the bars removed. Each batch of bars was then sealed in individual evacuated Vycor containers and heated for 24 hr at 1400°F in order to distribute the hydrogen homogeneously. After vacuum-annealing or hydroge nation, the bars were rolled at a temperature (1400°F) below the ß-transus to 1/2 - in. - diam rounds. Groups of the rolled specimens representing each of the hydrogen levels were given the following heat-treatments: 1) One hr at 1300°F, water-quenched. 2) One hr at 1300°F, water-quenched, and aged 8 hr at 1100°F. 3) One hr at 1300°F, water-quenched, and aged 4 hr at 1000°F. 4) One hr at 1300°F, water-quenched, and aged 48hr at 800°F. Heat-treated bars were machined into standard 0.250-in.-diam tensile specimens having 1-in. gage lengths. Throughout the processing and testing of this material, hydrogen analyses were made by vacuum-fusion methods to check for accuracy of hydrogen additions, homogeneity, and possible losses during processing. A summary of these analyses is given in Table II It may be seen that the actual hydrogen contents were reasonably close to the desired levels. In addition, it was noted that the variation in hydrogen content within any one bar did not exceed

Jan 1, 1959

By P. G. Pigott

The lack of technical information regarding the physical characteristics of kaolins and bauxitic kaolins, rejected during the mining of bauxite near Eufaula, Ala., has retarded their commercial utilization. This investigation was undertaken to determine their behavior when used in refractories. Ores were evaluated as refractory raw materials by compounding dry-press mixtures and specialties following procedures common to the industry. Products now on the market were used for comparison in laboratory evaluation.

Jan 1, 1959

By W. F. Campbell

One of the deepest coal operations today is the Springhill No. 2 mine of Cumberland Railway & Coal Co., subsidiary of Dominion Coal Co. Ltd. Mining is now conducted at a slope distance of 14,000 ft, with 4400 vertical ft of cover. The record of Springhill No. 2 can be said to contain the history of bumps in the Province of Nova Scotia. The Springhill coal field forms part of the Cumberland field of Carboniferous age. There are seven mineable fields in the area, numbered in the order they were discovered. Mining has been carried on in all but the No. 4 and 5 seams, but present operations are confined to the No. 2. Fig. 1 shows a vertical section through the seams. Opened in 1873, No. 2 mine was first worked from parallel slopes driven from the outcrop of No. 2 seam down to the 7700 level. As the mine went deeper, a two-place auxiliary slope was driven from the 6900 level to the present workings. A transfer level at the 7800 connects the main haulage with the auxiliary haulage slope. The No. 2 mine plan is shown in Figs. 2 and 3. The seam is bituminous, averaging 8.5 to 9 ft thick. There is a well defined parting 14 to 16 in. from the roof, and this roof coal is harder than the rest of the seam. Average pitch at the outcrop is 30°; at the 6500 level, 20°; at the 7900 level, 16°; and at the 13,800 level, 10°. Immediate roof and floor strata consist of beds of variable thicknesses of shales, grading to arenaceous shales to shaly sandstones to sandstones. A characteristic of the strata is the appearance and disappearance of sandstone bands, of considerable thickness, over distances of several hundred feet. MINE HISTORY Entrance to No. 2 mine is obtained by three parallel slopes, separated by 100-ft pillars except in the upper portion of the mine where the pillars are smaller. Main haulage levels were originally driven 600 ft apart for room and pillar extraction. A parallel drainage and intake airway was driven below each haulage level and a parallel return airway (counter level) above. Pillars 80 to 100 ft wide separated these two servicing entries from the center haulage level. Inclines up to 700 ft apart were driven off the levels up pitch to the upper levels, and at 40-ft centers level rooms 12 ft wide were driven off each side of the inclines, separated by crosscuts every 50 to 100 ft. The rooms were driven up to 350 ft or until they were holed into the room from the adjoining incline—a plan followed until the level reached its boundary. When the entire area between two levels had been divided into pillars, the pillars were extracted from the boundary back to the slope pillars. As depth of cover increased, mining conditions required larger pillars, and at the 3300 level, where NECESSARY PRECAUTIONS FOR MINING AT DEPTH In Room and Pillar Extraction: 1) Pillars must not be too small. 2) Pillar size must be uniform. 3) Extraction lines must be kept as straight and as uniform as possible. If they are irregular they should be brought back into line slowly. 4) Peninsulas of coal surrounded by gob must be avoided. 5) Pillars should not be disturbed after they have been formed. If it is necessary to increase the width of an opening, stripping or ribbing should be done gradually over a long distance. If increased width of openings is necessary at certain locations and can be anticipated, the openings should be widened during development. 6) Under no conditions should small pillars be left in the gob that would interfere with caving. In Long wall Operations: 1) Pillars formed during development for retreating longwalls should be uniform in size and shape. 2) Pillars should not be split after development, but if pillar splitting does become necessary it should not be carried out within the zone influenced by the working faces. 3) Width of levels should not be increased after the levels have been developed. If it does become necessary to widen a level it must be done gradually over a long distance by stripping or ribbing the coal ribs. 4) Extraction lines should remain uniform. If several walls are worked together—one behind the other—a uniform distance must be maintained between them and the wall faces must be kept as straight as possible. If the walls do get out of line, they must be brought back into line gradually to allow for a gradual change in the stress distribution over the area. 5) Stumps of coal, roof supports, etc. must not be allowed to remain in the gob to interfere with caving. 6) Midwalls should be built as rigidly as possible and properly maintained.

Jan 1, 1959

By W. Beckering

IN CHARACTERIZING tars obtained by the low-temperature carbonization or North Dakota lignite, infrared spectra have been an invaluable aid in both qualitative and quantitative examination. Quite early it became evident in the tar-research program of the Bureau of Mines, U.S. Department of the Interior, that the small number of published spectra available for hydroxy aromatics would be inadequate for comparative purposes when dealing with the wide range of compounds present in coal tar; therefore, compiling a catalog of spectra was initiated as a continuing part of the tar program. As these spectra should be valuable to other investigators in this and related fields, they are being presented in this report. This group or spectra (figs. 1-98) represent 97 compounds, largely phenolic materials. The major problem of this project has been the availability of materials for examination. Samples have been obtained from commercial and private laboratories or synthesized at the Bureau of Mines Lignite Experiment Station, Grand Forks, N. Dak.

Jan 1, 1959

By J. O. Betterton, D. S. Easton

A detailed investigation was made of the phase diagram of silver-zirconium, particularly in the region 0 to 36 at. pct Ag. The system was found to be characterized by two intermediate phases Zr2Ag and ZrAg and a eutectoid reaction in which the -zirconium solid solution decomposes into a-zirconium and Zr2Ag. It was found that impurities in the range 0.05 pct from the iodide-type zirconium were sufficient to introduce deviations from binary behavior, and that with partial removal of these impurities an increase in the a-phase solid solubility limit from 0.1 to 1.1 at. pct Ag was observed. The phase diagram of the silver-zirconium system is of interest as an example of alloying a transition metal from the left side of the Periodic Table with a Group IB element. Silver would normally act as a univalent metal, its filled 4d-shell remaining undisturbed during the alloying. However, there is a possibility that some of the 4d electrons might transfer to the zirconium. An insight into such a question can occasionally be obtained by comparison of phase diagrams. The silver-zirconium system forms part of a more complete review of various solutes in zirconium in which these valency effects were studied.' Earlier work on the silver-zirconium system was done by Raub and Enge1,2 who investigated the silver-rich alloys. After the start of the present experhents, work on this system was reported by Kemper3 and by Karlsson4 which for the most part agrees with the phase diagram presented here. EXPERIMENTAL PROCEDURE The alloys were prepared by arc casting on a water-cooled, copper hearth with a tungsten electrode and in a pure argon atmosphere. Uniform solute composition was attained by multiple melting on alternate sides of the same ingot. Progressive improvements in the vacuum conditions inside the apparatus during the course of the experiments reduced the Vickers hardness increase of the pure zirconium control ingot from 10 to 20 points, observed initially, to negligible amounts at the end of the experiments. Such hardness changes in zirconium are a well known indication of purity. For example, -01 wt pct additions of oxygen, nitrogen, and carbon increase hardness by 6, 10, and 3 VPN respectively. '9' Further verification that the final casting technique did not add a significant quantity of impurities was obtained when pure zirconium was arc cast and then isothermally annealed in the vicinity of the allotropic transition. The transition was always observed to take place over the same temperature range as in the original crystal bar. The alloy ingots were annealed in sealed silica capsules for times and temperatures which varied between 1 day at 1300°C and 60 days at 700°C. The best method found to prevent the reaction of the zirconium with the silica was foil wrapping of molybdenum or tantalum. With this method, samples of pure zirconium were found to be unchanged in hardness after annealing for 3 days at 1200°C. In most of the experiments the protection of these foils was supplemented by an additional layer of zirconium foil inside the molybdenum or tantalum foil. The alloys, foil, and the capsule were outgassed at pressures in the range 10 to l0-7mm Hg in the temperature range 800" to 1100°C before each anneal in order to remove hydrogen and other impurities, and to provide a suitable container for the high purity, inert atmosphere, which is essential in the annealing of zirconium. The temperature measurements were made with Pt/Pt + 10 pct Rh thermocouples calibrated frequently during the experiments against the melting points of zinc, aluminum, silver, gold, and palladium. For the longer anneals the sum of various temperature errors was generally well within ± 2°C. For short-time anneals and during thermal analysis the overall temperature error is considered to be within ± 0.5°C. The compositions of the alloys from the quenching experiments were determined by chemical analysis at Johnson Matthey and Company, Ltd., under the direction of Mr. F. M. Lever. The actual metallo-graphic samples were individually analyzed in every case, and prior to the analyses two or more sides of each specimen were examined to insure that the specimen was not segregated. The sum of the solute and solvent analyses was in each case within the range 99.9 to 100.1 pct. In the course of the experiments, minor impurities in the range 0 to 500 ppm were found to have significant effects on the zirconium-rich portion of the phase diagram. Similar effects had been encountered previously in other zirconium phase-

Jan 1, 1959

By C. L. Emery, A. V. Corlett

"The stress equilibrium is disturbed in a body of rock by a mine opening and is restored by a redistribution of the stresses around the opening. The pattern of the redistribution of unilateral stress around an opening has been established by mathematical analysis and photoelastic measurements. The pattern for multilateral stress is found by superimposition of unilateral fields. The mathematical analysts do not use the elastic moduli as parameters and they are not significant in photoelastic work. The medium is isotropic. The concept of unilateral stress from vertical loading and the classical pattern of its stress distribution around openings does not explain commonly observed failures around the perimeters of mine openings. They show evidence of compression where tension is postulated.When it is recognized that few minerals and perhaps no rocks are Hooke Solids, most rocks must be St. Venant Solids. The components have varying degrees of elasticity and viscosity. The assembly will be-have elastically to rupture under shock loading, but when loaded short of rupture will adjust viscously to equilibrium. Similarly, the highly elastic components may initiate rupture before equilibrium can be established when stress is instantaneously relieved. Polycrystalline adjustments may produce permanent deformation. The mechanics of consolidation, especially in sedimentary deposits, ac-quire a stress component normal to the direction of compaction which can exceed that of the loading. It is one source of prestress. There are others. The principles of prestress design are based on the normal beam reactions, modified by a built-in compression in the lower chord. When the beam is loaded to design limits, the lower chord retains some compression and the whole beam depth is effective in compression. Some of the . common evidences of failure in compression over a mine opening can be duplicated in a prestressed experimental model.When the triaxial stress pattern is recognized and suitable measuring techniques are devised, mine design can be done on a rational basis."

Jan 1, 1959

By L. Allan White

Instrumental analysis is an indispensable tool to many phases of research on rare-earth metals and their compounds; therefore, the development of new and improved instrumental techniques is essential. This report describes an emission spectrometric analytical method using direct-current carbon-arc excitation of various rare-earth-oxide mixtures. Lanthanum oxide serves the dual purpose of an internal standard and a constant major constituent. The versatility of the method was demonstrated by three different applications: (a) Analysis of complex rare-earth concentrates; (b) determination of impurities in high-purity rare-earth oxides; and (c) detection of rare-earth elements in other types of matrices, such as those resulting from beneficiation of rare-earth ores. The average error of analysis in the concentration range of 0.2 to 10.0 percent was 14.6 percent for a group of complex synthetic mixtures of rare-earth oxides. An average error of analysis in the concentration range of 0.05 to 0.50 percent was 21 percent for a group of high-purity rare-earth oxides.

Jan 1, 1959

By Andrew W. Jenike

The first significant studies of problems related to the handling and storage of bulk solids were reported at the end of the nineteenth century. Early work originated from the necessity to store large quantities of grain and was concerned mainly with pressures affecting the structural design of silos and bins. The Janssen formula (about 1898) and the work of Ketchum [1] form the highlights of that period. In more recent years, progress in mechanization, increasing plant capacities, and rising costs of labor have focused the attention of engineers on the problem of gravity flow of bulk solids. A great deal of work has been done with models, and flow patterns obtained in small scale bins have been described in several publications, for example [2, 3]. An attempt to develop a theory of flow of bulk solids was reported in 1954 [4, 5, 61 and presented to the in a paper [7] in the same year. AIME recommended the continuation of this work and, as a result, Engineering Foundation granted a sum of money to set up a Bulk Solids Flow Laboratory. Two and a half years ago the project gained the support of the University of Utah and a laboratory was set up on the campus of the University. This project is now in progress, it has received the support of the American Iron and Steel Institute and of Kaiser Engineers, Division of Henry J. Kaiser Company. The results obtained to date are summarized in this report.

Jan 1, 1959

By Charles T. Baroch, Corbin Allardice

Nuclear energy probably has greater potentialities for changing the world's way of life than any other recent discovery. The atomic-bomb bursts over Hiroshima and Nagasaki suddenly changed the concepts of war. Peaceful uses of nuclear energy are advancing so rapidly that no study of economic trends is complete without giving them consideration. The minerals specialist, especially, must be aware of this new force in our lives, as minerals and metals are essential in harnessing the new force, and atomic energy itself is rapidly improving its competitive position in the energy field. Future historians may chronicle December 2, 1942, as the beginning of the Atomic Age. On that day Enrico Fermi and his co-workers at the University of Chicago produced and controlled the first self-sustaining nu- clear chain reaction. Like many inventions, the first application of nuclear energy was as a weapon of war. However, its potential usefulness in man's work and welfare far outweighs in economic importance its destructive use in war, unless its military effect would be considered so great and all-embracing that no major power will hereafter chance a world conflict. Recognition of this potential has generated a vast international effort to exploit the atom for peaceful beneficent purposes. Like its physical manifestation, the advent of nuclear energy has unleashed chain reactions that have pervaded the political, social, and economic environments of the world. The impact of nuclear developments in one of many fields is exemplified by the uranium mining industry. Uranium was discovered in 1789 and in the next century and a half it found only an insignificant use as a ceramic coloring agent; in fact, in the latter part of that period, it was a largely unsalable by-product of the radium and vanadium industries. Up to 1940 the total quantity of uranium metal produced was not more than a few grams, of doubtful purity. Thus the production of 12,400 pounds of pure

Jan 1, 1959

By F. D. Delve

RECENT studies by the author on the reduction of titanium from TiO2-bearing slags have been accompanied by difficulties that are attributed to

Jan 1, 1959

By Arthur A. Brant

Your chairman has asked me to deal with questions of education relative to our present and projected trends in the field of mineral expiration. First comes our definition of education--and education is not the merely formal acquiring of academic knowledge, but the understanding, using and projection of knowledge into our channels of life and thought activity. This past year makes us realize the extent to which price and economic cut-off may stimulate or curtail exploration,, But exploration does not consist solely in the discovery of sources of material. There is just as inspiring and imaginative a territory in the develop¬ment of uses and application--and no one in our base metal industry but would hope that our educational processes would fertilize those springs of inspiration that lie dormant in us all, toward the- imaginative conception of new uses--lead roofing cloths or felts, non-tarnishable copper utensils, further zinc solid state application. Thus an educational pattern should seek to develop imagination and thinking beyond--the possibility of that small but oh so difficult step just ahead of the existing,

Jan 1, 1959

By R. N. Zitter

PRESENT work was done in connection with a program for obtaining a low energy gap semiconductor suitable for photodetection. The inter-metallic compound InSb, which is now being in-

Jan 1, 1959

By Farrel W. Lytle

Instrumental analysis has become an indispensable tool in research and production of the rare-earth elements. This development can be attributed mainly to a combination of two factors--the marked chemical similarity of the rare-earth elements, which excludes classical methods of analysis, and the speed and accuracy of instrumental-analysis techniques. With continued improvements in methods of producing high-purity rare-earth elements, keeping pace instrumentally is becoming much more difficult. Accordingly, greater emphasis is being placed on improving instrumental limits of detection and accuracy. The methods employed most frequently for determining impurities in rare-earth elements involve use of the optical-emission spectrograph (3, 4)4/ and the spectrophotometer (9). Although numerous X-ray-emission spectrographic methods (6-8) have been developed for analyzing rare earths, these techniques have not included detection of low-level impurities. This investigation was conducted to find the precision and accuracy of X-ray fluorescence in deter-mining impurities in rare-earth oxides in the 0.01-to 1.0-percent-concentration range.

Jan 1, 1959

By G. Ostberg

OXYGEN has frequently been considered responsible for phenomena in the metallurgy of cast iron which are not sufficiently explained by the presence of other elements. Oxygen and oxides have been regarded as critical factors, particularly for the solidification process, and specifically in the formation of graphite. However, the evidence for an influence of oxygen has mostly only been indirect or qualitative. Furthermore, quantitative data on the oxygen content of cast iron presented in the literature have often been less conclusive as being apparently determined with insufficient regard for the difficulties associated with the sampling and analysis. These problems, experimental and theoretical, have been studied in this investigation. An attempt is made to bring the views on the soluble amount of oxygen in cast iron on a level with the present understanding of the thermodynamics of these types of alloys. Although there are no experimental data on the complete multicomponent cast-iron alloys some conclusions have been drawn from investigations on simpler systems. The order of magnitude of the solubility of oxygen in cast iron is considered in the first part of the paper. The second part deals with the oxygen content actually present under practical conditions. First the possible sources of errors in sampling and analyzing methods are examined. Finally some observations on the oxygen and oxide content of malleable iron during the production process are made. THERMODYNAMICS OF OXYGEN SOLUBILITY When cast iron is saturated with oxygen the saturation phase is essentially carbon monoxide or silicon dioxide depending upon the composition of the iron, the temperature, and the rates of formation of the oxides.* The latter occurs accordiw to the O + C = CO, Kc0 - a COa J 20 + Si = SiO2, Activities are used here instead of weight pct concentrations, since activities are believed to show more sensitively the effects of the interaction of all the alloying elements. Calculations involving activities are, however, seriously hampered by lack of experimental data on the interactions between the components encountered in the multi component cast-iron system Fe-O-C-Si-Mn-P-S- and so on. In order to make an estimate of the oxygen solubility reason-

Jan 1, 1959

By H. G. Wolfhard

The mode of propagation of explosions through narrow passages is important for understanding flameproofed equipment employed in mines. Narrow channels have been used in this investigation that connected between a small explosion chamber and a large chamber containing fuel-air mixture. The oxygen index of the mixture in the small chamber was determined which caused an explosion in the outer chamber. Preliminary measurements have already been given in Bureau of Mines Report of Investigations 5457 and suggested that) flames do not pass through narrow channels. The hot, burned gases from the explosion in the small chamber, however, are able to ignite the mixture in the large chamber by a process of hot-gas ignition. Systematic measurements are reported in the present paper that cover the influence of channel length and diameter and the properties of the gas mixtures in the large chamber on the transmission of explosions. The influence of such properties as quenching diameter and flame temperature is also discussed. This paper concludes the work on this problem and presents a theory that describes in detail parameters that influence transmission of explosions through narrow channels. INTRODUCTION Flameproofed equipment in mines is usually provided with flanges. A gap between the opposing flanges allows ventilation and release of pressure. The safe gap width has been determined for a number of flange lengths by Smith4/

Jan 1, 1959

By J. L. Schroeder, W. G. Talman

EXPERIENCE has shown that certain known natural conditions and other indefinite characteristics combine to make a mining area vulnerable to mountain bumps. Some of the known conditions are heavy overburden, an overlying stratum of strong non-elastic rock, a structurally strong coal seam that does not crush easily and yet is the weakest stratum in the series, and a floor stratum of more than ordinary firmness. The indefinite characteristics could include resistance of top or bottom of a coal seam to lateral flow, effect of immediate top and bottom strata, nature of the coal seam, and other factors about which very little is known. It is in this area that exhaustive study is needed to achieve positive control of the dreaded mountain bump hazard. In the Gary district, West Virginia, two of the five operating mines have areas known to be vulnerable to mountain bumps.These are the No. 2 and 6 mines, which are working the Pocahontas No. 4 coal seam. In this area the seam is overlain at a zero to 10-ft interval by the massive Eckman sandstone, which is about 100 ft thick in the vulnerable areas. Total overburden, consisting of shale, coal seams, and sandstones, ranges from 700 to 1400 ft where bumps have occurred (Fig. 1). The coal seam is 4 to 8 ft thick and has a weak columnar structure of very soft and spongy or woody coal. The immediate top is either the Eckman sandstone or hard shale, both of which provide generally good roof conditions for mining operations. The bottom ranges from medium to hard gray shale. The incidence of bumps in the Gary district dates from about 1930 and can be correlated to some degree with the increased rate of extraction attained with mechanical mining. During early years of operation at the No. 2 and 6 mines, most of the work was development and under comparatively light cover. As overburden became heavier, together with an increasing percentage of coal coming from pillar extraction, mountain bumps began to occur. Before 1945 they were much less severe than in later years, and because there were no injuries or fatalities, no records were kept. But by 1951 the incidence of bumps had increased to such extent that it became evident a mining system would have to be designed to eliminate or at least minimize these occurrences. Drawing on experience with modified versions of old systems and certain characteristics peculiar to the Pocahontas No. 4 coal seam, the district mining engineer, Martin Hayduk, outlined the essential factors for bump control in the Gary district. These control factors indicated: 1) The highly stressed area, which lies within the limits of convergence effects, moves at approximately the same rate as the retreating pillar line. 2) There is a decided softening of the periphery of blocks which is greatest and deepest on the gob side. 3) Blocks less than 45 ft wide never have been known to bump in the Pocahontas seams. Fig. 2 shows the mining plan based on these observations—a thin-pillar system with a minimum of secondary development. It was recognized from the start that the Hayduk system had certain limitations. When pillar work backed up to an inevitable surrounded block it was no longer applicable; also, burnt bottom and/or unknown factors reduced the system's effectiveness in certain headings. Since there was no way to eliminate the loaded block, it was decided to experiment with auger drilling to attain controlled release of this stored-up energy. The decision to auger was made after consideration of three separate plants, which were: 1) To cut the solid block into pillars of maximum size by driving away from the fracture line and at such a distance outby that development

Jan 1, 1959

By B. J. Reid, J. N. Greenwood

It has been shown1 that cavities are formed in the grain-boundaries of copper and 70:30 brass (as well as in magnesium) by the application of tensile stresses at elevated temperatures. For a given rate of strain, cavities are formed in brass at a lower temperature than in copper, and they are larger; it was thought that this earlier onset of cavitation in the alloy might be caused by the distortion produced in the metal lattice by the alloying element. If the cavitation is caused by the vacancy-migration mechanism, ' the distortion of the lattice would reduce the energy required for vacancy formation, and thus provide vacancies more readily to assist in the cavitation process. It was decided to study a range of alloys to find out whether increasing amounts of an alloying element would cause any progressive increase in, or modification of, the cavitation in copper. Nickel was chosen for this purpose, since it is soluble in copper throughout the whole range of alloys. A further advantage was its low vapor pressure, which enabled the preparation of the alloys in vacuum and the consequent reduction of their hydrogen content. It has been suggested that cavities may be nucleated by the migration of hydrogen atoms to the less regular atomic spacing at the boundary, and their combination to form molecules. The latter being too large to diffuse back into the lattice, form stable cavities into which vacancies could condense. PREPARATION OF ALLOYS All alloys, ranging from pure OFHC copper to 43.7 at. pct of nickel (carbonyl), were prepared in a vacuum furnace employing high-frequency induction heating. When a charge was melted, vigorous gas evolution occurred initially, after which the pressure was reduced to 10-4 mm Hg, using an oil-diffusion pump. After remaining molten for a further 1/2 to 1 hr to aid degassing, the melt was allowed to solidify in the crucible. In this way contamination by gases evolved from the surface of a separate mold was avoided. The list of alloys prepared is shown in Table I. The percentage of hydrogen present in the OFHC copper was reduced from 0.0054 at. pct to 0.0012 at. pct, as measured by a vacuum-fusion method. The alloys were cold-rolled to 0.03-in.-thick strip, and were homogenized in vacuum for 1 hr at 900°C after every 30 pct reduction. At a thickness of 0.05 in., the strip was held at 450°C for 24 hr under high vacuum (10-5 mm Hg) in an attempt to reduce the hydrogen content still further. Tensile specimens were prepared with a gage length of 1 in., and were finally annealed for 2 hr at 800°C to give an average grain diameter of 0.1 mm. TENSILE DEFORMATION The specimens were deformed in a tensile straining machine operated by a synchronous motor at a constant rate, equivalent to 1.7 pct per hr on a 1-in. gage length. The specimen and grips were contained in a vacuum jacket. A pressure of 10-2 mm Hg was maintained, which was sufficient to prevent surface tarnishing of a specimen held at 650°C for 24 hr. Tests were made between 20. and 650°C and the temperature was controlled to within ±3° over the gage length. The load was measured by the deflection of a cantilever spring. a) Mechanical Properties-The ductility curves shown in Fig. 1 fall into two groups. Figs. 1(a) and (b) for copper and the 5 pct nickel alloy, respectively, show a continuous fall in ductility with a steep fall between 200° and 400°C. Figs. l(c) to (f) show the same sudden loss of ductility between 200° and 400°C. With higher temperatures, however, there is a recovery in ductility values to a maxi-

Jan 1, 1959

By H. N. Smith

IN 1944 the Congress passed the Synthetic Liquid Fuels Act that authorized the Secretary of the Interior, acting through the Federal Bureau of Mines, to conduct basic research and construct and operate demonstration plants to produce synthetic liquid fuels from coal, oil shale, and other substances. As a basis for the oil shale investigations to be undertaken in this country, the progress of foreign countries in developing and using oil shale as a source of liquid fuels was studied by the technical missions of the Federal Bureau of Mines. Oil shale mines, retorting plants, and refineries were visited; geological information on the nature and occurrence of the foreign oil shales was obtained; and samples of the oil shales were collected where possible. Samples collected by these missions or acquired by other means came from Australia, Brazil, Canada, France, Manchuria (China) , New Zealand, Scot-land, Spain, Sweden, Thailand, and Union of South Africa. These countries represent a large part of the locations where oil shale developments have taken place. The major omissions are the Estonian, German, and Russian developments.

Jan 1, 1959

Common brattice cloths in use in Australian coal mines are compared by permeability measurements. The respective advantages of twill weave and tarpauling* weave cloths are listed, and the improvements to be obtained in the ventilation of a mine by using tarpauling cloths instead of the commonly used twill cloths are stressed. Plastic cloths are widely used overseas and are briefly discussed.INTRODUCTIONThe onset of extensive full-scale mechanization in Australian coal mines during the past few years has increased attention given to the ventilation of working places. Many inadequacies of the present system have been brought to light and not the least of these is connected with the use of brattice cloth, both in directing the flow of air around the face and in acting as a temporary sealing mechanism. A well-constructed line of brattice will only provide fair ventilation for a distance of 100 ft. Beyond this point the volume or air reaching the face falls off rapidly.Some of the shortcomings associated' with the use of brattice cloths are:1. Hurried installation, necessitated by a rapid advance, often results in poor workmanship with, consequently, an excessively high leakage rate.2. High places caused by falls of roof are difficult and time-consuming to seal.3. Curtains, in lines of brattice crossing transport routes, are difficult to maintain.4. Lines of brattice interfere with rock-dusting and clean-up of fine coal.5. Repair and maintenance of brattice consumes much...

Jan 1, 1959

By A. L. Engel

This investigation was undertaken to assess the feasibility of processing an extensive deposit of iron ore near Palisades, Eureka County, Nev., previously penalized for high phosphorus content. The experiments described indicate a satisfactory accomplishment of objective. Chemical treatment will permit a high-phosphorus iron ore to be used. Leaching with acid solution effectively lowers the phosphorus content with a [gligible] loss of iron. The use of hydrochloric acid is preferred because [ ] does not contaminate the ore and the cost is lower. Minus-1/2-inch ore was satisfactorily leached in 24 hours, minus-1/4-inch ore, in 8 hours, and minus-10-mesh ore, in 3 hours. About 40 pounds of acid per ton of ore was consumed in each instance.

Jan 1, 1959