Search Documents

By R. J. Leary

The natural gas-air burner described in this report was designed and constructed to meet the thermal requirements of a convective process for heating steel scrap. This process involved downward combustion of natural gas with air, blending the combustion products with diluent air, and then passing this tempered stream of gases downward through a porous bed of steel scrap contained in the furnace chamber. The scrap would be heated to a temperature limited by the adiabatic flame temperature of the gas stream in a period that depended on the rate at which heat was supplied per unit of bed cross section. The temperature of the gas stream would be limited to that beyond which an objectionable degree of oxidation would occur; for carbon steel this limit had been found to vary from 1,900° to 2,100° F. with the superficial velocity of the gas stream. The productivity of the process was dependent on the rate of heat input per unit of furnace cross section; for the 3-foot-diameter experimental furnace an input of 680,000 B.t.u. per hour was desired. The burner described was designed to meet these conditions of temperature and heat input. It provided for three streams of entering gases: (1) A primary air-fuel mixture too rich to be combustible, that is, above the upper flammable limit; (2) secondary air for combustion of the primary mixture; and (3) tertiary air, principally for cooling the combustion products to the temperatures desired for process operation. Downward combustion of the primary and secondary streams occurred in a flame stabilized on an annular port, while tertiary air flowed in an annular path surrounding the port and also through an axial channel whose wall formed the inner ring of the annular port. This burner performed beyond the designed heat-input rates while producing stable flames, which were adjusted readily to the temperatures desired. Gas-stream temperatures were easily controlled to within 15° F. of the desired value by simple manual adjustment of the flow valves.

Jan 1, 1959

By J. W. Freeman, J. P. Rowe, R. F. Decker

HEAT-to-heat variations in properties of an alloy of constant nominal chemical composition have been a perplexing problem to the metallurgist. These heat-to-heat differences have been especially baffling in high-temperature metallurgy. In order to establish fundamental reasons for these heat-to-heat variations, the National Advisory Committee for Aeronautics has sponsored and financially assisted an extended research program on heat-resistant alloys at the University of Michigan. As part of the program to find the contribution of processing variables, Frey, Freeman, and white' studied effects of heat treating on nickel-base alloys and Ewing and reeman' investigated effects of hot-working practice on N155 alloy. To extend the program to the study of effects of melting practice on high-temperature properties, a 55 Ni-20 Cr-15 Co-4 Mo-3 Ti-3 pct A1 composition was selected for experimentation. The objective of this program was to establish the melting-practice variables which influenced the hot-working characteristics and creep-rupture properties and, at the same time, establish the metallurgical mechanisms for the effects. During the course of the investigation of practices using vacuum melting, it became increasingly evident through chemical analyses supplied by industrial concerns that a major variable was melt reaction with the crucible. This paper is devoted to the results of this phase of the melting-practice study. EXPERIMENTAL PROCEDURES Experimental 10-lb heats were induction melted in the University of Michigan vacuum-melting unit with the melting practices outlined in Table I. Aim analysis for the basic alloy, in wt pct, for all heats was as follows: Cr Co Mo Ti Al 20.0 15.0 4.0 3.1 3.1 Mn Si C Ni 0.12 0.12 0.08-0.15 Bal. Small amounts of boron and zirconium were added to certain heats as listed in Table I. These additions

Jan 1, 1959

By D. H. Baker

THIS REPORT presents the technique and equipment used in determining the hardness of titanium sponge. Detailed descriptions are given of the methods used in preparing test samples for chemical analysis and hardness testing, the method of melting and surfacing test ingots, and the technique of reading Brinell-hardness impressions. The arc-melting furnace described, for which engineering drawings are included, will produce from 70 to 90 double-melted buttons each 8 hours of operation. Experimental data are also presented depicting the effect on hardness of the methods of surfacing specimens, temperature of test specimens, and the effect of time at test load. These data show that surfacing of the specimen involves no critical machining operations but that the test surface must be paralleled by a relatively flat surface for contact with the anvil of the Brinell tester. The heating of a specimen to 150° C. during surfacing does not materially affect the results if the ingot is cooled to room temperature before the hardness impressions are made. The optimum time at load appears to be approximately 30 seconds, but load times of as much as 1/ ½ minutes will not cause major errors.

Jan 1, 1959

By John C. Machisak

Employment and related injury experience of the coking industry in the United States for 1957 contained in this publication is summarized under three general sections: (A) General injury experience: Tables 1 to 9: Current and comparable statistics on operating data, number, frequency, and degree of severity of injuries and major accident agencies involved in the cause of Injuries. Data are presented for the industry as a whole, for each type of oven, and for the States in which coke was produced.

Jan 1, 1959

By F. W. von Batchelder

The principles of microradiography and their application practically coincided with the discovery of X-rays. These principles were first used in the metallurgy field by Heycock and Neville1 in a study of the dendrite structure of alloys of Au-Na, Au-A1, Cu-A1, and Ag-A1. The method was introduced in the USA by clark2 after a visit to France. Scores of papers have been written, and a very complete bibliography on this subject was compiled by the Eastman Kodak company. Although a number of papers have discussed X-ray

Jan 1, 1959

By Adolph V. Mitterer

International Minerals and Chemical Corporation operates one of six potash mines in the Carlsbad potash basin. More than 90 percent of America's potash is produced at Carlsbad and IMC accounts for about one-fifth of that amount, Since the Company began operations in 1941 it has mined nearly 50 million tons of ore. Of the two types of ore mined at Carlsbad the principal tonnage is sylvinite in which sylvite-potassium chloride-is the ore mineral. It is produced by IMC as well as by all other mines in the area, In addition to sylvinite IMC is the exclusive producer of langbeinite ore--potassium-magnesium sulfate. From its two ores, International produces a spectrum of 8 high-quality agricultural and industrial chemical products.

Jan 1, 1959

By R. Haynes

ON the basis of compositional changes of a phase observed in a eutectoid Cu-Al alloy1 it has been suggested that mechanisms for the decomposition of the ß phase proposed by earlier workers2-5 were incorrect. These data are reinterpreted in conjunction with lattice parameter data obtained on an alloy containing 12.2 pet Al, whose isothermal transformations have been reported elsewhere.5 The a Lattice Parameters of a 12.2 Pet A1-Cu Alloy—~iffraction patterns of completely transformed specimens were obtained in a back reflection camera using copper Ka radiation. Lattice parameters of

Jan 1, 1959

By John J. Mulligan

Ear Mountain is an isolated mountain mass that rises abruptly from the coastal plain on the northwest shore of the Seward Peninsula. Geologically it resembles the more accessible Brooks Mountain and Cape Mountain areas to the southwest, being composed of a granitic core surrounded and partly capped by metamorphosed sediments. The occurrence of lode- and placer-tin deposits in this area has been known since the early 1900's, when the Seward Peninsula region was prospected extensively for both gold and tin. The Federal Bureau of Mines investigated the tin deposits in the Ear Mountain area during the 1953 and 1954 field seasons. The objectives were to delimit the areas in which tin minerals occur, as a guide to future prospecting, and to determine the amount of tin in the known prospects. Work by the Bureau of Mines included both placer and lode sampling.

Jan 1, 1959

By L. A. Roe

Magnetic separation of iron ores is one of the fastest-growing segments of the minerals beneficiation industry. The tonnage of taconite ores processed annually by magnetic separation will, in a few years, reach 100 million. Magnetic separation occupies an attractive position in the field of ore beneficiation. It is a simple yet effective method, used for some 150 years and steadily growing more important. This type of beneficiation orginated in 1792, when William Ful-larton was issued a British patent covering the separation of iron ore by magnetic attraction. What is magnetism, and why are some materials capable of being magnetized and others not The study involves many unknowns, and even a partial answer to these questions would be a dissertation in solid state physics and perhaps other fields of science. But the last two decades have revealed basic facts as to why certain materials are magnetic and what happens to them when they are magnetized. Some of the newer studies in solid state physics have developed a theory that can be applied to studies of magnetism. It is claimed that magnetism stems fundamentally from the spin of electrons in atoms that tend to go in pairs, spinning in opposite directions. The atom as a whole can act as a magnet only when there is an imbalance of electronic spin. Whenever an atom has an odd number of electrons, therefore, this imbalance exists. This neutralizing effect explains why a piece of material that contains atomic magnets is not necessarily magnetic. The physicists tell us that iron is composed of many small magnetized regions called domains, which consist individually of millions of atoms. The piece of iron becomes magnetized when an external force lines up these domains in the same direction. Fundamental data developed by physicists working in fields far removed from minerals beneficiation are now available for developing better magnetic separators for ore processing. More Data Needed on Magnetic Properties of Minerals: There is less information on magnetic properties of minerals than there is for certain aspects of magnetic separator design. When the data on magnetic properties is available, it is often directed toward the study of powders for tape recorders and other highly scientific endeavors that are of little use to the beneficiation engineer. W. R. Crane's table of tractive forces, published in 1902, is still a guide in the study of magnetic minerals. Bits of other information regarding electrostatic conductivity, dielectric constant values, and permeability of various minerals have also appeared but are of small practical value in magnetic separation of ore. It is extremely important to obtain pure mineral specimens for making investigations and to record results that may be of use in studies of magnetic processes. Reference to the large volume of data developed by those concerned with analysis and design of permanent magnets soon reveals that these people have extensively evaluated the effect of various impurities on magnetic properties. Much of the science of the ferrite industry is based upon spinel-type structures which are varied by substitution of selected elements or even subtraction of elements, leaving vacant sites in the space lattice. Magnetic separators are used to beneficiate a wide variety of industrial minerals. In this application the relatively large volumes of nonmagnetics are usually the commercial products. The amount of mag-

Jan 1, 1959

By C. M. Schwartz, A. P. Young

ZIRCONIUM is noticeably embrittled at room temperature by hydride precipitate not only in notch-impact tests but also in tensile-impact tests.' The embrittlement in slow-strain tensile samples is much less severe. To understand better the relationship of the hydride precipitate to the strain-rate effect in tensile samples, the surfaces of chemically polished zirconium tensile samples strained at a slow rate (0.03 in. per min head speed) and at an impact rate (18.1 fps hammer speed) were examined in the light and electron microscopes. Vacuum-degassed samples and hydrogenated samples (100 ppm hydrogen) were examined. The hydrogenated samples were slow cooled from 800°C. The most apparent difference between slow-strain and impact tensile samples was the preponderance of twinning over slip in impact samples as opposed to relatively little twinning in slow-strain samples. The twin bands in hydrogenated samples often terminated on hydride needles as seen in Fig. 1. Almost opposite the twin terminus is a fine crack and a nearly round fissure. Holes near the areas where single lens-shaped twins or opposing pairs terminate on hydride particles also could be seen In the light micrbscope. Quite frequently, microcracks associated with a partial row of hydride particles were visible, as in Fig. 2, indicating that the crack was parallel to a row of hydride particles. Some samples were chemically polished after straining to remove metal with a minimum of disturbance of internal voids. Fig. 3 shows a crack in the interior of a hydrogenated impact sample. Holes along grain boundaries were seen after impact in both degassed and hydrogenated samples. Very few microcracks were seen in degassed samples after impact or slow strain, or in hydrogenated samples after slow strain.

Jan 1, 1959

By Martial P. Corriveau

The preparation of coal is essentially the same for export as it is for the domestic market. The big difference, I would say, is that, while coal for certain domestic uses (utilities, for instance) need not always be of the highest quality, as long as it is uniform, the buyer of coal for export invariably demands a well-prepared, top-quality product. And he is willing to pay for it, as long as he knows what he is buying. This is where quality control enters the picture. The day is long past since the export market was the dumping ground for coals which could not be sold on the domestic market. Today, the export buyer wants American coals not so much for a price but for the necessity of blending the American coals with foreign coals to achieve the desired chemical and/or physical characteristics, To blend intelligently, he must know in detail what are the qualities of the coals to be blended. Sampling and chemical analysis facilities at the piers provide the information on the coals exported, These facilities are maintained for the export buyer by independent laboratories; however, in one instance, the buyer operates his own laboratory. With very few exceptions, and Clinchfield?s Moss No. 3 mid-volatile coal is one, cargoes shipped overseas are loaded as blends of two or more coals. Up to now, foreign requirements have not been too clearly defined; therefore, shippers must be prepared to blend mixtures of the desired combination. Successful blending requires an accurate knowledge of the coals shipped. And this makes it necessary for the coal producer to maintain his own control laboratory.

Jan 1, 1959

By J. B. Gayle

The merits of the various methods for dry-quenching coke have been the subject of numerous publications and almost equally numerous controversies for the past 40 years.5/ Most investigators have concluded that dry quenching is advantageous. Some have based their arguments on the improved physical properties of the resultant cokes. Others have claimed little or no improvement and have based their arguments on the economies acquired from the recovery and utilization of sensible heat. The extent to which the method of quenching influences the properties of the resultant cokes is of importance in connection with the operation of both commercial and experimental ovens. On the other hand, the recovery and utilization of sensible heat are economic problems related solely to commercial oven operation and- depend on the method of dry quenching used and the demand for a low intensity energy source. The scope of the present Bureau of Mines investigation has been limited to a comparative study of the properties of wet- and dry-quenched cokes produced from six coals and blends carbonized at flue temperatures of 2, 000° and 2,400° F. in the Tuscaloosa oven.

Jan 1, 1959

By H. L. Miaw, A. M. Gaudin, D. W. Fuerstenau

A quantitative method for evaluating density of slime coatings has been developed and applied to formation of iron oxide slime coatings on quartz and on corundum. Slime coating density is related to flotation recovery and to properties of the electrical double layer at mineral surfaces. IN spite of considerable study, the nature of slime coatings in flotation is still not completely understood. However, phenomena that control floc-culation and dispersion of colloidal systems are now interpreted in terms of electrical double layers.",' Colloids will flocculate even though the particles carry the same charge, but when two dispersed colloids of opposite charge are mixed. flocculation ensues even more rapidly. Analogous phenomena seem responsible for slime coating on minerals in flotation systems. To shed new light on the issue it was considered desirable to devise a tool that would measure slime coatings. The usual method has been to examine photographs of presumably representative surfaces, after. an intervening washing in running water. But such an examination is non-quantitative, and the changes in chemical environment represented by the washing may have removed the slime coatings that existed during flotation. To provide the possibility for a correlation with electrical double layer phenomena, the experiments were made with quartz, corundum, and iron oxide, for which elec-trokinetic data are available.'-" Since the properties of the electrical double layers of these oxides depend on the pH of the solution, pH will be the most important variable. Furthermore, because the zero point of charge for silica, iron oxide, and alumina occurs at pH 3.7, 8, and 9.5, respectively, the relative charge on the slime and mineral can be changed over wide ranges. Because of its practical importance in quartz flotation, iron oxide powder was chosen as the slime. Also, its uniform composition, contrasting color, and ease of analysis make experimentation simple. In this investigation, correlation was sought between the effect on flotation recovery of slime addition and slime coating density. Materials and Methods Details are available in a thesis by Miaw." The quartz was selected from pure Brazilian crystalline quartz, crushed, sized (65/150 mesh) acid-cleaned, washed, and stored in conductivity water. The corundum (synthetic alumina of high purity prepared by Linde Co., Chicago) was crushed, sized (65/100 mesh) deslimed, boiled in nitric acid, washed, and stored in conductivity water. The iron oxide slime, reagent-grade ferric oxide (—400 mesh) from Allied Chemical & Dye Corp., was heated to 160°C, cooled, and stored in a vacuum desiccator. In the electron microscope the slime particles appeared to be about 0.3µ in size, but their large specific surface (87,900 cm per g, by gas-adsorption method, using krypton) suggests that the actual particles are smaller than 0.3r. Had they been perfect nonporous spheres, they would have had a diameter of 0.13µ.

Jan 1, 1959

Coal Division Industrial Minerals Division Minerals Beneficiation Division Mining, Geology and Geophysics Division Established as a Society February 26, 1957 OFFICERS AND COMMITTEES J W Woomer, President A B Cummins, President-elect S D Michaelson, Past President C E Lawall, Eastern Regional Vice-President D W Scott, Central Regional Vice-President 3 D Forrester, Western Regional Vice-President R B Ladoo, Treasurer John Cameron Fox, Secretary

Jan 1, 1959

By H. C. Carpenter

Data are presented comparing results obtained with 17 different catalysts in hydrogenating crude shale oil to gasoline in single-pass operation. A method is described for predicting the maximum yield of gasoline obtainable at constant pressure for each catalyst from results of a limited number of experiments at different temperatures. Operating variables have considerable influence on yields and properties of products. With most of the catalysts, at operating temperatures below 890° F. liquid yield exceeded 100 volume-percent. Above this temperature the volume of liquid product decreased rapidly. Maximum gasoline production in most instances was achieved at a temperature higher than that at which the maximum volume of liquid product was produced.

Jan 1, 1959

By O. Q. Leone

Excellent metal quality, with lower power requirement, is attained in electrorefining titanium by using internal heating of the fused-salt bath. An internal heater provides more effective heat utilization, simplifies structural components in cell design, and prolongs cell life by eliminating direct application of heat to the cell container. This Bureau of Mines report covers one phase of the research in progress at the Electrometallurgical Experiment Station at Boulder City, Nev., for improving the techniques and lowering the total power requirement for electro-refining titanium metal.

Jan 1, 1959

By M. G. Zabetakis

This publication presents a simplified graphic method for determining the explosibility of mine atmospheres under mine-fire conditions from mine- atmosphere composition data. Sometimes it is necessary to seal part of a mine during a fire to exclude air and thus extinguish the fire. Unfortunately, liberation of methane and formation of hydrogen and carbon monoxide in the sealed area may create an ex- plosive or flammable atmosphere if enough oxygen is present to support combustion. On the other hand, the oxygen concentration may be reduced through combustion processes and the concentration of inert gases (nitrogen and carbon dioxide) increased enough to render the atmosphere within the sealed area non-explosive. Before an area is unsealed, it is extremely important to know if the sealed atmosphere contains Flammable gases in proportions that might form explosive mixtures when air is introduced. If an explosive mixture forms and the fire is rekindled, a gas explosion will result. Various experimental methods may be used to determine the explosibility of a particular mine atmosphere; however, these methods usually are impracticable in the field.

Jan 1, 1959

By S. L. May

The Bureau of Mines has developed several methods for extracting tantalum and columbium (niobium) and the rare-earth compounds from ores and concentrates. A cooperative agreement was made by the Bureau with Porter Bros. Corporation of Idaho to process 200 pounds of its euxenite concentrate by methods that had been developed at the Albany, Oreg., Metallurgy Research Center. The euxenite concentrate was processed to extract and purify the valuable metals by chlorination, solvent extraction, and hydrometallurgical techniques. Chlorination was used to convert the valuable constituents into chlorides and to partly separate them. Solvent extraction techniques were used to separate the tantalum from the columbium. The rare-earth and uranium compounds were purified by hydrometallurgical methods.

Jan 1, 1959

"Acta Metallurgica" Dennis Carney, '59 Alfred Noble Joint Prize Committee F B Foley, Dec '61 American Association for the Advancement of Science F T Agthe, Dec '59, William L Fink, Dec '60 American Geological Institute Arthur Montgomery, Oct , '59, F C Kruger, Oct '60 American Power Conference J P Weir, T D Hess American Society for Testing Materials

Jan 1, 1959

By John J. Mulligan

The creeks draining Cape Mountain, on the western tip of Seward Peninsula, Alaska, comprise the Cape Mountain tin-placer district. Because of the war-caused shortage of tin, the Bureau of Mines in 1943 conducted a churn-drill placer reconnaissance to explore the district. Favorable indications were found, and plans were made for further investigation of the deposits; the plans were abandoned when tin again became plentiful. In July 1951 the Zenda Gold Mining Co. was granted a Defense Minerals Administration (Defense Minerals Exploration Administration after October 1951) loan to continue exploration of the more favorable areas indicated by results of the Bureau's investigation. Equipment was moved to the area in the fall and winter of 1951-52. During the 1952 field season, 209 churn-drill holes totaling 7,521 linear feet and 10 test shafts totaling 96 linear feet were sunk on the Cape Creek drainage. Work was resumed in 1953, when 56 churn-drill holes totaling 3,157 linear feet were drilled on Boulder Creek. The company planned to drill Goodwin Gulch and Goodwin Creek, but no further work was done owing to lack of capital.

Jan 1, 1959