Search Documents

By W. D. Sylwestrowicz

In tests on polycrystalline copper and aluminum, the ratio of the yield stress to modulus of elasticity was found to be strongly dependent on tempemture. Also, it was shown that the change of the yield stress with temperature of a material at a given temperature and deformed to a given yield stress, but not necessarily to the same strain, does not depend on previous mechanical thermal history. Likewise, for a material at a given temperature and deformed to a given yield stress, the rate of work hardening is independent of the temperature of prior stressing. It has been shown by Los and Orowan1 and by Dorn, Goldberg, and Tietz2 that the temperature dependence of the yield stress-strain curves of crystalline materials reflects two effects: not only does the yield stress of a material in a given structural state depend on the temperature, but the structural state (and the corresponding strain hardening) after a given amount of plastic straining also depends on the temperature at which the pre-straining has been carried out. Thus, for instance, if a specimen of a ductile metal has been strained along the stress-strain curve 1 at room temperature to point A, Fig. 1, and then the straining continued in liquid nitrogen along curve NR, the yield stress A' immediately after lowering the temperature is lower than the yield stress A" of a specimen that has been strained by the same amount in liquid nitrogen (along curve 3). AA' represents the effect of the temperature change upon the yield stress of the specimen pre-strained at room temperature; A' A" is the excess strain hardening acquired if the pre-straining has been carried out in liquid nitrogen instead of at room temperature. The dependence of the yield stress (i.e., of the structural state acquired during preceding straining) upon the conditions (speed, temperature) of a pre-straining is the reason for the nonexistence of a so-called "mechanical equation of state" for plastic deformation. A 'mechanical equation of state" is a relationship of the form F(s,E, e, T) = 0, or s = f(E, E, T) [1] It was first suggested by Ludwik3 that plastic deformation might obey such an equation; this, however, was conclusively disproved by experiments of Kochendorfer.4 Additional disproofs were given in

Jan 1, 1959

By J. F. Martin, J. E. Friedline, L. M. Melnick, G. E. Pellissier

A method has been developed for determining gases in steel in which the gases are extracted by vacuum fusion and analyzed by mass spectrometry. This method is especially applicable for determining small amounts of oxygen and nitrogen. The lower limit of detection for both oxygen and nitrogen is 0.0001 pct with an average deviation of about 0.0001 pct for oxygen and 0.00008 pct for nitrogen. Hydrogen analyses by this method are in good agreement with analyses by vacuum tin-fusion. A complete analysis of all gases extracted from a steel sample can be accomplished in 40 min. It has long been known that certain of the gaseous elements exert particular effects on the physical and mechanical properties of steel. With the recent advent of new experimental steelmaking practices it is now possible to obtain steels with extremely low contents of such elements as oxygen and nitrogen. Present methods for determining these two gases are of insufficient sensitivity as applied to steels made by these newer practices, and therefore a new technique was considered necessary. A review of the literature showed that the conventional vacuum-fusion method1 was the procedure most suitable for modification to obtain a sensitive method for determining the gaseous elements present in steel simultaneously. However, for trace amounts of gases it is impractical to increase the sample size because of the physical limitations of the apparatus and the increased degassing time which would be necessary. Also, when only one of the desired gases is present in trace amounts, quantitative separation by conventional vacuum fusion is almost impossible. Since small analytical mass spectrometers are now commercially available, it was decided to use this instrument in conjunction with conventional vacuum fusion for both qualitative examination and quantitative determinations of the gaseous elements in steel. This technique has already been used with success for the analysis of copper and lanthanum.2"4 APPARATUS A vacuum-fusion unit was first designed and built, Fig. 1. This unit was designed especially for the determination of small amounts of nitrogen and/or oxygen in steel since an acceptable method (vacuum tin-fusion)5 was already in use for the determination of hydrogen in steel. The vacuum system was con- structed of Pyrex glass throughout. Mercury check valves were used in place of stopcocks in the high-vacuum section of the system. Ferromagnetic samples are normally introduced into the vacuum system through a mercury lift. In case of a break in the lift, the mercury is prevented from entering the furnace by a self-locking, mercury safety check valve, Fig. 2. This check valve, developed at our laboratory, is a modified T/S ball-and-socket joint placed in the sample inlet system between the mercury and the furnace. A sudden entry of mercury or air pushes this valve into the closed position, completely blocking the top of the mercury lift. The check valve is held in the closed position by the vacuum of the apparatus. A separate entrance tube also was placed in the system, so that samples which would amalgamate with mercury, or which are nonmagnetic, could be introduced into the furnace. A slightly modified Guldner-Beach furnace is used in this system.8 The optical flat was connected to the system by a ground-glass joint to facilitate cleaning, a quartz delivery tube was substituted for Pyrex, and the crucible was used uncovered. Fusion takes place in a high-purity graphite crucible insulated by — 200-mesh high-purity graphite powder. The crucible set (crucible and funnel) is suspended in a quartz crucible. The furnace envelope and the sample inlet system are exhausted by 2 single-stage, mercury-diffusion pumps in series. The first of these is a high-speed pump, which will work only with a very low backing pressure. This pump is used to exhaust the gases from the furnace as rapidly as possible. The second mercury-diffusion pump is used as a backing pump for the first; the capacity of this pump is much lower. However, it will work efficiently against a back pressure of 3 mm of mercury. To assure positive pumping, a modified Naughton and Uhlig condenser7 is used. With the use of proper valving the second pump is also used as a circulation pump in the catalyst system.

Jan 1, 1959

By R. J. Charles

F. C. Bond: This is an outstanding paper on comminution theory and represents a considerable advance in mathematical formulation. It clears the way for a discussion that should ultimately decide whether the work index should be considered as a parameter according to the Third Theory or as a constant. In the empirical differential equation dE = —Cdx/x [1] either Corn must be treated as a variable to satisfy known crushing and grinding conditions. The author has chosen the exponent n as the variable, with C as a constant. According to the Third Theory, in the general case n is a constant equal to 3/2, and C is a variable related to the work index Wi. If x is placed equal to P (the size in microns which 80 pct of the product passes) and F is the size 80 pct of the feed passes, then C equals 5 W1, and dE = 5 -5 Widx/x = 10 Wi 10 Wi w = vP vF which is the basic equation of the Third Theory. It is apparent that this integration involves the error of treating the parameter Wi as a constant, just as the author's treatment involves the error of integrating his variable n as a constant. These errors are probably relatively unimportant, considering the small range of the variables. When more is known about the factors contained in the work index, Eq. 1 can be revised as a partial differential equation. The Third Theory exponent of 1/2, or n = 3/2 in the Charles' differential equation (Eq. l), was not chosen primarily because it is the average between the Kick and Rittinger exponents; this may be merely fortuitous, since it is illogical to define truth as the average between two errors. It was first discovered from the study of a large mass of crushing and grinding data and confirmed by laboratory testing. The general correspondence of the Third Theory equation to actual crushing and grinding results over the entire size reduction range argues strongly that a fundamental phenomenon is involved. The a posteriori theoretical explanation of the constant Third Theory exponent is that the work done in breaking rock is proportional to the length of the crack tips formed. Compressive force applied to the rock results in deformation and strain energy. When this locally exceeds the breaking strength a crack tip forms, the surrounding strain energy flows to the crack tip and extends it to split the rock, with release of the energy as heat. Under rapid impact the crack tip may form before the strain has reached equilibrium, resulting in less energy expenditure and probably a coarser product. In any case, the elastic limit of a brittle material is practically the same as its breaking strength, and the work necessary to form the crack tip is the work required to break. The crack length of a ton of broken rock cannot be measured directly. However, the particle shapes of feed and product are similar, and the crack length is considered equal to the square root of one half of the new surface area formed. It is, therefore, proportional to 1/vD, where D is the equivalent product particle diameter. This is the basis of the Third Theory equation. Many secondary factors can be imposed upon the crack length breakage. These may cause the Third Theory work index to increase or decrease somewhat as the product size becomes finer. The work index is properly a parameter rather than a constant, making it an increasingly valuable practical criterion of the work input required in crushing and grinding.

Jan 1, 1959

By F. J. Darnell

SINGLE crystals of a-titanium are difficult to obtain because of the phase transformation at 882 °C in which the structure changes from the high-temperature body-centered structure ß to the low-temperature hexagonal close-packed structure a. Preparation of single crystals of a-titanium has previously been accomplished by a strain-anneal method which takes several days and is not generally reproducible. Single crystals as large as 5 mm

Jan 1, 1959

By L. A. Wrigglesworth, A. S. Dadson

The orebodies of the Giant Yellow-knife mine occur in zones of schist, in an assemblage of typical Precambrian greenstones which form part of the Yellowknife Greenstone Belt. One of the most interesting problems at the mine concerns the fold-like attitudes assumed by the schist zones. The internal structure of the zones and orebodies provides much evidence of folding. A logical conclusion would be that the zones represent a single horizon which has been folded and drag-folded in the ordinary course of mountain building. However, surface mapping, and correlation of certain marker horizons, in underground work, indicate a homo-clinal succession of steeply dipping flows. If this concept of the geology is correct, the zones must cross-cut the regional strike at a small angle and, in the over-all aspect, the regional dip at a large angle. A mechanical interpretation of the zone structure is presented as a suggestion for the present until new evidence is found.

Jan 1, 1959

By R. Bakish, C. S. Barnett

IN experiments on tantalum strained in tension, Bechtold did not observe deformation-twinning even at a temperature as low as that of liquid air.' This is an unexpected behavior for a metal of body-centered-cubic structure. Therefore, it is desirable to determine whether the lack of twinning is an inherent characteristic of this particular metal, or whether the reluctance to twin can be overcome under suitable conditions. The following experiments were performed under conditions favorable to twinning and cleavage in their competition with slip, namely, with impact loading on large-grained sheet at low temperatures. The crystallography of cleavage in tantalum sheet was also investigated carefully because of the remarkable ductility of tantalum at low temperatures and because recent tests on oxygen-embrittled tantalum had disclosed unusual cleavage behavior for a metal of this structure: cleavage primarily on (110) planes and only occasionally on {100}.2 The tantalum, supplied by Fansteel, was of 99.9 pet purity, with the chief impurities being iron (0.03 pet) and carbon (0.03 pet). Coarse grains were produced by the strain-anneal method, the anneal being 4 hr at 2000°C in a vacuum of 10-3 mm Hg, followed by furnace cooling. Impact deformation was applied in various ways: a) by hammer blows on an anvil, the specimen and anvil being immersed in liquid nitrogen ( —196°C), b) by driving a precooled center-punch into the sheet, and c) by bending around a crystallographically determined axis with a hammer blow. The impact-deformation produced bands and slip lines on the surface, Fig. 1. The bands have every appearance of being deformation twins, a) They are tilted with respect to the untwinned surface. b) They have the appearance of Neumann bands in iron, thin lens shape, some having serrated edges. c) The orientation in each is different from that of the surrounding matrix and uniform within a given band, see slip lines within them in Fig. 1. d) Upon repolishing and etching, the difference in orientation and the resemblance to Neumann bands is again evident, Fig. 2. (In this micrograph the slight bend in the bands as they cross grain boundaries was noted frequently and results from the high degree of preferred orientation in the sheet.) e) The bands persist after annealing treatments that would have removed them had they been a low-temperature martensitic phase, e.g., after an anneal of 1/2 hr at 900°C. When back-reflection Laue data were plotted for single-surface analysis of several grains, every trace of the bands in each grain could be explained by (112) planes. In addition, two of the bands were located in space by traces on two surfaces, and these also were found to lie on (112) planes within the error of the stereographic plot. Since (1 12) is the anticipated composition plane for deformation twins in body-centered-cubic metals it is felt that the observations listed above are conclusive evidence for the identification of the bands as twins. Similar tests with impact at —77° and at 25°C produced no twinning. It is concluded that the critical shear stress for slip at the rates of straining used was always low enough to prevent the applied stress from reaching the value required for twinning at these temperatures. It was noted that the serrations along the edges of the twin bands exhibited parallel crystal facets. Several similarly oriented notches are visible in Fig. 1, and a remarkable set is shown in Fig. 3. It appears from Fig. 1 and similar areas that notches are frequently associated with the intersection of a slip line with a twin, although not all such intersections are at notches. In some instances a slip line appears to enter the twin, cross it, reflect from the opposite side and recross it, producing a pattern resembling a notch but without producing the notch itself, see Fig. 1. It is suggested that the stress concentration at the end of a slip line is responsible for these details. The strain energy associated with the pile-up of dislocations at a twin boundary may be lessened by untwin-ning or failing to twin a portion of the twin band, or

Jan 1, 1959

This issue presents the first of several articles making up the Bump Symposium, which was held at the 1958 Annual Meeting of AIME. Other Symposium papers will appear in the September issue of Mining Engineering. THE term mountain bump describes the sudden rupture of one or more coal pillars under excessive stress. These bursts occur with varying degrees of violence and sometimes include adjacent strata, especially the bottom rock. Many failures do not develop enough violence to be dangerous and are regarded as an aid to coal production, but severe occurrences are accompanied by tons of flying coal, dense clouds of dust, and excessive gas emission. Such bursts sometimes throw heavy machinery several feet. Major factors to be considered in the problem are the nature of the strata above and below the seam and the depth of cover. Bumps are classified as to their nature, extent of damage, and point of occurrence, e. g., face bump, coal bump, high side bump, low side pavement bump, and district bump. The problem is extremely complex, and it cannot be over-emphasized that preventive measures, if they are to be successful, must be based on a thorough study of conditions in the individual mine. In western Canada, for example, the McGillivray mine, operating in a 9-ft seam at 2000 ft, has experienced severe bumps, but there have been no occurrences in the International mine, which operates in the same coal seam at 2400 ft, where the coal averages 17 ft thick. Differences in conditions governing the operation of these two mines are described in one of the following articles (see page 883). Again, most bumps in coal mines take place along pillar extraction lines, but at the Sunnyside mine in Utah they also occur a long way from active workings and sometimes in virgin territory. It is usual, too, for such failures to occur under fairly deep cover. But at Sunnyside, to cite only one instance, there have been disturbances along the main fault zone under less than 500 ft of cover. All too often conditions favorable to bumps are revealed only by actual mining—at Springhill No. 2 mine, drilling in roof and pavement strata disclosed a 60-ft sandstone bed after operations had started— and where extraction has advanced too far for preventive measures to be incorporated in the mining plan, districts have had to be abandoned. But in an era when premium ores are being rapidly depleted in the face of rising demands, abandonment is not easily justified. There must be systematic planning to eliminate coal mine bumps, insofar as this is possible. As in the Gary district of West Virginia (see page 888) much has been accomplished by planned operations based on known factors in bump control. But even this is not enough. Precise instrumentation is needed to indicate where bumps are likely to occur, and in both the U. S. and Canada stress analysis studies are being carried out with this object in view. These pages reveal the progress being made.

Jan 1, 1959

By I. S. Servi, N. F. Graves

THE etch-pit technique has long been used to reveal low-angle boundaries and, in general, the distribution of dislocations in high-purity metals. Often this technique is amenable to quantitative computations,' but generally is affected by some degree of uncertainty because etch pits can be nucleated not only by dislocations, but also by inclusions and surface imperfections. In the case of high-purity zinc, Gilman' reported that etch pits were produced only after adding 0.1 atomic per cent of cadmium to the crystals and aging at a proper temperature. In the course of a study of low-angle boundary behavior in zinc crystals, etch pits were produced in 99.999 pct zinc without resorting to intentional contamination, by etching in a 50:50 HNO3H2O solution. The technique consists of etching until the heat of reaction brings the solution to a boil, and in displacing the etchant rapidly with a stream of cold water, thus avoiding staining. The undesirable features of this technique are the heating effect and the removal of a considerable amount of material. A high polish is obtained if staining is controlled properly; therefore, the etch pits appear very clearly and with excellent contrast when observed under dark field illumination. This is especially helpful for cursory examinations at low magnifications. Several observations were made on zinc crystals of square cross section, having one face parallel to the basal plane and one edge parallel to a slip direction, Fig. l(a). When such a crystal was bent about 2" over a glass die and annealed at 390°C, a sharp boundary was formed only in the inner portion of the crystal. Near the two prismatic faces, perpendicular to the basal plane, the boundary was always branched into many lower-angle boundaries, Fig. 1(b). Attempts to move the main boundary by applying a shear stress to the specimen invariably resulted in curving the boundary, the branched ends remaining pinned in their original location, Fig. 1 (c). The prismatic face, when etched as indicated in the foregoing, revealed the existence of numerous (sometimes up to 30) fine boundaries, nearly parallel to each other. Pre-existing lineage boundaries, generally parallel to the direction of growth, were barriers to the formation of polygonization boundaries and interrupted the continuity of the substructure, Fig. 2. Twin

Jan 1, 1959

By L. C. Weiner

THIS study was undertaken to round out an investigation on the effects of solid environments on the brittle fracture of zinc single crystals.' In the previous work it was demonstrated that the presence of a surface film increased the cleavage strength of crystals whose basal planes were oriented almost parallel to the tensile axis by some 43 pct. This increase was observed to be independent of the type of surface-coating material, as well as of thickness of film above a certain small critical value (about 200 to 300A). These observations were described sat- isfactorily by a dislocation-pile-up-at-a-barrier model of brittle fracture2 in which twins modifying the dislocation path act as barriers, their increase in number and homogeneity of distribution brought about by the presence of the surface film. From previous work reported on the strength of ductile metal crystals as affected by gaseous and liquid environments,3 it may be concluded that the effects of these media are present only when the environment produces a surface film on the initially clean-surfaced crystal, or when it has a disintegrating effect on a previously existing surface layer. Similarly, it might be expected that an increase in cleavage strength of initially clean zinc crystals (xo = 3", A, - 28") will result only when the gas or liquid reacts with the crystal to produce a solid, adherent surface film. Clean-surfaced crystals,l 2 1/12 in. in length, were tested in tension at room temperature in an Instron

Jan 1, 1959

By L. S. Castleman, L. L. Seigle

THE formation and growth of intermetallic phase layers is of considerable practical importance to metallurgists interested in diffusion bonding and cementation processes and has been the subject of extensive qualitative investigation. In contrast, it is somewhat surprising that so little quantitative data have been amassed. The need for additional fundamental work was pointed out by Mehl in 1936,' and persists to a large extent to the present day. The early studies have been reviewed by Rhines,2 and his conclusions have been summarized by Lustman and Mehl3 substantially as follows: 1) All phases that are stable at the temperature at which diffusion occurs will appear in the interdiffusion of two metals; however, in some cases, certain of the phases may be too thin to be observed and identified easily. 2) The isothermal growth of intermetallic phases generally obeys a simple parabolic equation of the form X2 = Kt, where x is the thickness of the alloy layer, K the temperature dependent reaction rate constant, and t the time. 3) The rate of thickening varies with temperature according to the Arrhenius equation k = Ae -Q/RT , where k is the parabolic rate constant, A, a temperature independent constant, Q the heat of activation for the process, R the gas constant, and T the absolute temperature. Subsequently, Lustman and Mehl made a quantitative study of the laws of growth in intermediate layers in a number of binary systems, in which one of the components was either zinc or cadmium, and the other component was one of the following: nickel, copper, silver, cobalt, gold, iron, or Monel metal; the interdiffusion times used were for the most part less than 24 hr. It was found that the simple parabolic law was not obeyed in general, but that a generalized parabolic law of the form xn = kt was valid, where n was a temperature dependent constant; also,

Jan 1, 1959

By H. E. Mauck

The many factors that control bumping must be carefully studied for each coal seam where bumps occur, and specifications known to exclude bumping should be incorporated in the mining plans. This calls for complete knowledge of the seam's characteristics and its adjacent strata, and in many instances these characteristics are not revealed until the seam is actually mined. Pressure and shock bumps, the two general types, occur jointly and separately. In this discussion no differentiation will be made. Whether pressure or shock, they are treated as bumps, and both must be eliminated. Bumps in mines have occurred in several places throughout the coal fields of the world. A study of many of these occurrences indicates that geologic characteristics, development planning, and mining procedure have contributed. But more specifically, there are conditions usually associated with bumps: thickness of cover, strong strata directly on or above the seam, a tough floor or bottom not subject to heaving, mountainous terrain, stressed and steeply pitching beds, and the proximity of faults and other geologic structures. Mine planning should incorporate these known factors (not necessarily in order of importance): 1) Main panel entries should be limited to those absolutely necessary to ventilate and serve the mine. This reduces the span over which stresses may be set up that will later throw excessive pressures on barrier and chain pillars when they are being removed. 2) Barrier pillars should be as wide as practicable so that they will be strong enough to carry the loads thrown on them when final mining is being carried out. 3) Pillars should never be fully recovered on both sides of a main entry development if the barrier and chain pillars are to be removed later. The excessive pressures placed on the main chain and pillar barriers by arching of the gob areas can result in bumping when these barriers are being removed. 4) Full seam extraction is better accomplished by driving to the mine boundary and then retreat-drawing all pillars. If there are natural boundaries in the mine—such as faults, want areas, and valleys —retreat should be started there. 5) Pillars should be uniform in size and shape. The entire development of the mine should call for uniform blocks with entries driven parallel and perpendicular. Only angle break-throughs should be driven when necessary for haulage, etc. 6) For better distribution of rock stresses and reduction of carrying loads per unit area, both chain and barrier pillars should be developed with the maximum dimensions. 7) Pillars should be open-ended when recovered. If they are oblong, the short side should be mined first. Both sides of a block should not be mined simultaneously, but under no circumstance should the lifts be cut together. 8) Pillar sprags should not be left in mining. If they are not recoverable, they should be rendered incapable of carrying loads. 9) Pillar lines should be as short as practicable. (Three or four blocks are adequate). Experience has shown that rooms should be driven up and retreated immediately. The longer a room stands, the more unfavorable the mining conditions. This contributes to bumping. 10) Pillars should not be split in abutment zones (high stress areas lying close to mined out areas) and if slabbing is necessary, it should be open-ended. 11) Pillars should be recovered in a straight line. Irregular pillar lines will allow excessive pressures thrown on the jutting points. Experience has shown that the lead end of the pillar line can be slightly in advance. 12) Pillar lines should be extracted as rapidly as possible. This appears to lessen pressures on the line and render abutment zones less hazardous. 13) Extraction planning should call for large, continuous robbed out areas. Robbing out an area too narrow to get a major fall of the strata above the seam tends to throw excessive pressures on a pillar line. 14) Timbering in pillar areas should be adequate but not excessive. Too heavy timbering or cribbing is likely to retard roof falls and throw excessive weight on the pillar line. 15) Experience has shown that when pillar lines have retreated 800 to 1000 ft from the solid, bumps can occur. Because this distance may vary in different seams, impact stresses should be studied for each individual condition. In any event, extra precautions should be taken against bumps in this area. This list of controlling factors may or may not be complete. It probably is not, but it covers most of the problem's significant aspects. The question is whether or not bumping can be eliminated. The answer is that bumping can be minimized and possibly eliminated if these and other established factors are thoughtfully considered and incorporated in the mining and extraction plans. If a mine has already been developed or the pattern set so that little change can be made, then it will be necessary to adjust to the most nearly practicable system that can incorporate the known factors.

Jan 1, 1959

By Granville S. Borden

The fruits of industry are divided between capital, labor, and governments. Capital takes its redemption and remuneration through profits or dividends; labor takes its share through wages; governments take their share through taxes. Each must have a just share, and the question of what is a just share and the question of who-shall make the allocation are vital current political and economic issues. Certain political philosophies con- tend that government should take all the fruits and that some dictator or politician should have irrevocable discretion and power to distribute the fruits. Believers in democracy and free enterprise adhere to the view that capital is entitled to redemption and fair remuneration; that labor shall have a fair wage; and that governments shall make equitable levies. But since all human beings, both individually and in groups, are inherently selfish, there are many variable views in regard to the question of what ratios shall be applied in a division of the fruits and who shall have the power to fix these ratios. Perhaps all parties should devote more energy to means of increasing the crop, and not so much time to quarreling over a division of the existing crop. Moreover, all three parties must guard against killing the goose that lays the mineral eggs. For example, if the tax burden becomes oppressive and the taxpayer refuses to carry it, then business stagnates, with consequent unemployment, reduction of profits, and curtailment of government revenue. If a producer assumes the increased tax burden, marginal operations must be closed down, and again the consequences are increased unemployment and diminished government revenue. Quite often an increase in a rate of tax results in a reduction of government revenue. Perhaps the worst detrimental feature of selfishness and greed on the part of any one of the three distributees of the fruits of industry is the retardation of expansion of the enterprise. Growth means new jobs, more government revenue, better trade, and better standards of living. Explorations and discoveries have resulted in tremendous contributions

Jan 1, 1959

By King D, Dickinson S. B, Matheson R. S

Graham Hall and V. M. Cottle (Rosebery, Tas.) : In their paper on "The Mineralized Rift Valleys of Tasmania", Campana, Dickinson, King and Matheson have summarized a wealth of data from many sources. In proposing the new concept of a rift valley structure, they claim to have found a new guide to regional ore control and distribution in North-west Tasmania.Although the authors acknowledge suggestions made by us prior to publication of the pa:per, we are still at variance with their conclusions. We are not convinced that a rift valley structure exist~d when the Ordovician conglomerate was deposited. We are unable to find evidence for Cambrian deposition in a rift valley or reason to project the structure to embrace Hercules, Rosebery, and "possibly" Mt Bischoff.That the Great Lyell Fault (the authors' Owen Rift Fault) is a promising place to look for ore is not a new idea, but the existence of important ore deposits away from the structure reveals its inability to provide an adequate explanation of regional mineral distribution. A well-known structure that does have an influence on ore deposition is not discussed by the authors.STRUCTURAL CONSIDERATIONSThe great thickness of coarse unsorted Ordovician conglomerate lying in an elongate but narrow belt of country is presented as evidence of its deposition centrally within a rift valley, the position-of which is now said to be outlined by resistant slabs of the conglomerate. The marginal shears of the rift are said to show up well along the edges of the conglomerate.

Jan 1, 1959

By A. S. Yue, A. G. Guy

A study was made of the effects of a prolonged flux of zinc atoms through the a solid solution of zinc in copper. The experimental arrangement consisted essentially of a copper disk about 0.01 in. thick, at one of whose surfaces a gaseous atmosphere containing zinc atoms was maintained, and at the other surface a gaseous atmosphere with a minimum of zinc atoms was maintained. During prolonged theothersurfaceexposure at high temperatures the zinc content of the copper disk gradually built up to the steady-state concentration distribution and then remained at this value. The concentration-distribution curves for various conditions were determined by chemical analyses. The results showed that the condition of steady-state diffusion was achieved. The diffusion coefficients calculated from the experimental data, although not of high precision, agreed with the values obtained by other workers using unsteady-state methods. Relatively slight porosity developed in the specimens in the course of diffusion. A LTHOUGH most diffusion studies have been made under unsteady-state conditions, it is known' that the steady-state method is often superior with respect to the directness and accuracy of interpretation of the data. Steady-state diffusion of gases through metal diaphragms is well known. Also, Harris' and Smith" have used the steady-state method in studying the diffusion of carbon in aus-tenite. The accepted mechanism in this system involves the motion of the interstitial carbon atoms in the rigid framework of the lattice of iron atoms. Thus, there is little difficulty in visualizing the steady flow of the small carbon atoms through the austenite. The situation in substitutional diffusion is quite different. Here the atoms are comparable in size, and it is not evident how a steady flow of one of the atoms through the solid solution might be achieved. At the time the present research was started, it was known that a previous exploratory attempt to produce steady-state diffusion in a substitutional alloy, the Au-Ag system,' had been unsuccessful and had indicated that perhaps there were basic difficulties that could not be ovei-come. Therefore, the present research began as a study of the effect of a prolonged flux of metal atoms through a substitutional solid solution. Eventua.lly, it was possible to produce actual steady-state diffusion in the system chosen for study, the a Cu-Zn alloys. Experimental Procedure The aim in the experiments was to maintain a high zinc content, about 30 pet, at one surface of a copper sheet, and to maintain a low zinc content, near 0 pet, at the opposite surface. The zinc would then diffuse into and through the copper, first building up to the steady-state concentration distribution and then maintaining this distribution. The three types of specimens that were used are shown in Fig. 1. In type A specimens the copper disk through which diffusion occurred was welded to the top of a cylindrical molybdenum tube, the bottom of which also was sealed by welding. At the diffusion temperature the brass chips in the molybdenum container were the source of the zinc vapor which maintained the lower surface of the copper disk at 30 pet Zn. The upper surface was maintained at 0 pet Zn by the vacuum in which type A, and also type B, specimens were diffused. Since the molybdenum container was impervious to zinc vapor, it was intended that the only path of escape for the vapor from the brass chips would be through the thin copper diffusion disk. However, it was found that small leaks often developed at the welded joints during the diffusion treatment, and in most specimens some of the zinc was lost in this manner. Although even small losses of this kind were a serious handicap in attempting to determine the flux through the disk, they did not prevent the maintenance of satisfactory boundary conditions for the attainment of the steady-state condition. Type B specimens differed from type A in having a weight of about 300 g supported on the copper disk by 15 to 20 short quartz rods. This change was made when it was observed that the copper disk was being bowed upward by the difference in the pressures acting on its two surfaces. Since the grain-boundary cracking which occurred in the bowed specimens could be attributed largely to the accompanying creep,3 it was desirable to minimize this effect. The counterweight was effective in significantly decreasing both bowing of the disk and cracking at grain boundaries. Type C specimens differed considerably from the others in that the low-zinc atmosphere at one sur-

Jan 1, 1959

By H. R. Shell

Variations between laboratories on the silica and alumina content of calcined kyanite led to this Bureau of Mines study of the extent and nature of the differences. In particular, Bureau scientists hoped the study would lead to correction of the causes of the dissimilarities. A sample of calcined Kenya kyanite was analyzed by seven different laboratories familiar with silicate analysis. The compiled data indicated differences originating from lack of recovery of silica after two acidic dehydrations, from high alumina caused by several factors, from loss or gain of iron during sample fusion, and from indifference regarding the accurate determination of minor constituents.

Jan 1, 1959

By R. G. Charles, E. A. Gulbransen, S. Barnartt

KINETICS of the reaction of zirconium with pure oxygen at elevated temperatures have been studied by several workers for periods of time up to 6 hr.1-1 In two cases,3-4 . the experimental values of oxygen uptake, w, as a function of time, t, were best fitted to the parabolic rate law w2 = kPt + constant. In others,3,4 the cubic rate law w3 = kot + constant, showed better agreement. The most recent data of Gulbransen and Andrew4 indicate that the choice between the parabolic and cubic laws for empirical representation of the data will often be arbitrary. This is particularly true if the first few minutes of the reaction with a clean zirconium surface is attributed to a different oxidation mechanism, for deviations from either rate law were found primarily during the initial period. Thus, the kinetics of this reaction have been too uncertain to permit safe extrapolation to oxidation periods of practical interest (many hundreds of hours). The data to be described are of interest, for they indicate that the cubic rate law applies over long oxidation times. The reaction of zirconium with oxygen at 1 atm pressure was followed at 350" and 450°C for 500 and 200 hr, respectively. Abraded test specimens of pure zirconium sheet' 3.0 X 2.0 X 0.012 cm in size were oxidized by the procedure previously described,3 which included periodic cooling to room temperature for weighing. The surfaces were polished to a 4/0 finish using polishing paper wet with kerosene, then wiped with petroleum ether and washed in redistilled acetone. Fig. 1 shows plots of log ? vs log t. Each curve represents the average of duplicate measurements, and deviations from the average were generally less than 3 pet. The cubic rate law (slope = 1/3) is closely followed. The rate constants, 5.2, x 10 -6 and 2.4, X 10- (mg cm-2)3 per hr at 350" and 450 oC, respectively, are plotted as log k, vs 1/T in Fig. 2, together with cubic constants calculated from the data of Gulbransen and Andrew4 for abraded specimens from the same lot of zirconium. Their data refer to runs of 6-hr duration at a pressure of 0.1 atm 0 and under conditions of uninterrupted heating. In spite of these differences, the latter data yield a straight line which appears to apply equally well to the new extended time data. The energy of activation for the oxidation process, calculated from the slope of this line, i.s 38 keal per mole. This may be compared with the value of 47 keal per mole found by Belle and Mallett3 at higher temperatures. It may be concluded tentatively that extrapolation of short-term oxidation data for zirconium to obtain the long-term behavior is best done through the cubic equation ?3 = kpt + constant. References ' E. A. Gulbransen and K. F. Andrew: AIME Trans., 1949, vol. 185, p. A.515; JouRNal OF Metals, August 1949. 'D.p. Cubicciotti Journal Amer Chemical August1949.Soc., 1950, Vol. 72, P. 3 V. Belle and M. W. Mallett: Joulnal Electro chemical Soc., 1954, ' E. A. Gulbransen 339.and K. F. Andrew: Oxidation of Zirconium Between 400" Gulbransenand 800'C.and AIME Trarzs.. 1957, vol. 209, p. 394; JOUR-Nal of Metals, April 1957. IS Barnartt, B G. Charles, and E. A. Gulbransen: Oxidation of 50 weight pet uranium-zirconium alloy, Journul Electrochemical SOC., 1957, vol. 104, p. 218.

Jan 1, 1959

By C. Chiou, M. E. Fine

While Gunier-Preston zones are growing in Al-4.2 pct Cu at room temperature, Young's modulus, measured dynamically, increases about 0.4 pct. From the change in modulus with time the exponent of time in the rate equation for growth of the zones was deduced to be %. From a comparison of the rates of increase of modulus at 1, 28, and 42°C an activation energy of 12 to 14 Kcal per mole is computed. These findings support the idea that copper atoms are supplied along dislocation channels to growing zones. In alloys the elastic constants will be functions of the distributions of the atoms. If the degree of ordering or clustering is changed, one expects a corresponding change in the elastic constants. During age-hardening of aluminum-copper alloys at room temperature, the copper atoms cluster on 100-type planes in the aluminum lattice forming

Jan 1, 1959

By J. L. Lytton, J. E. Dorn, L. A. Shepard

Single aluminum crystals were subjected to creep in simple shear on the (111) planes in the slip direction. The activation energies for creep were calculated from the effect of small abrupt changes in temperature on the creep rate just before and immediately following the temperature change. The results definitely establish the fact that creep of single aluminum crystals occurs by-three unique processes, characterized by thethree distinct and isolatable activation energies: The 35,-500-cal-per-mole activation energy obtained at the highest temperatures was ascribed to a dislocativationtion climb process; the 28,000-cal-per-mole activation-energy process, occurring over the intermediate-temperature range was attributed to a cross-slip mechanism; and it was suggested thot the 3400-cal-per-mole process observed below 400°K may be the Peierls energy. THE most pertinent question regarding the phenomenon of creep in crystalline materials is concerned with the identity of the crystallographic mechanisms of deformation that control the creep rate. For many years slight progress was made in uncovering the basic mechanisms for creep. Over the past 10 years, however, two parallel lines of investigations have contributed to a more definitive understanding of the processes involved in creep. The extensive development and maturing of dislocation theories for deformation of crystalline materials' proved to be of paramount importance for this progress. And second in importance was the replacement of the former prosaic methods of creep testing by new techniques'." which were especially

Jan 1, 1959

By T. F. Archbold, R. E. Grace

The use of interference colors is the simplest experimental way to determine the approximate film thicknesses of oxides formed on liquid metals. A large amount of data under various conditions can be obtained easily and quickly. The oxidation of liquid lead has been studied by several investigators,1-5 but all of these studies have been on thick oxide scales. The purpose of- this work was to investigate the range 0 to 2000A film thickness. By using electron diffraction, Jenkins concluded that the surface of the film on molten lead is yellow orthorhombic PbO with the (110) planes parallel to the surface. This was confirmed by Shimaoka and Yamai7 who also used electron diffraction from the melting point of lead to 730°C. The rate of oxidation of pure liquid lead in air was measured in the temperature range 453" to 643°C by observing the rate of formation of interference colors on static lead baths. Approximately 170 g of lead (99.999 pct) was placed in a refractory dish having a working surface of 13.8 sq cm. This crucible was placed in a deep-well resistance furnace open to the atmosphere. The times at which the various interference colors appeared, after wiping the molten metal surface clean, were determined at 453", 533°, 600°, and 643°C. Elapsed times were determined with a stopwatch and all colors were estimated by eye. Bath temperatures

Jan 1, 1959

By Staff

"The Weyburn Oil Field, located 80 miles southeast of Regina, Saskatchewan, was discovered by Central-Del Rio Oils Limited, in January, 1955. As of January 1st, 1959, the field had 357 wells capable of producing an estimated total of 45,100 barrels of oil per day.Highly portable, economical, drilling rigs are used to penetrate the pay at a depth of 4,400 to 5,100 feet. Presently, the complete drilling operation for an average field well, including drilling, coring, testing, and running casing, requires 12 days. Drilling procedures are conventional for a field of this depth and no serious problems exist. Central-Del Rio core the productive section of all their wells, which provides valuable information for well completions and reservoir studies. Production casing procedure is to set through the zone and perforate the productive inter-val. This was found advisable due to the lensing nature of the porosity and permeability throughout the reservoir, and to the high connate water saturation encountered in the tighter sections of the reservoir in the north and northeast areas of the field.Although a few wells in the field have produced naturally by flowing or pumping without acid treatment, it has generally been necessary to acidize the wells to make them commercial producers. To date, acid treatments appear to effect better stimulation of the limestone reservoir than fracturing treatments. Perforation sealing balls have been used as an aid in selectively treating all of the perforated interval.The majority of the field is on pump, producing at a low gas-oil ratio. The main part of the field has water-free production, with most of the water being produced in the north and northeastern area. Salt-water disposal is now available in the field through two disposal wells completed in the Basal Blairmore sand.The Midale Beds ""Marly"" and ""Vuggy"" zones form the principal reservoir, which is a stratigraphic trap, with the north and northeast edges terminated by a porosity and permeability pinch-out and the south-west and west edges bounded by water-laden porosity. There is no evidence to date of a gas cap. The reservoir apparently is producing on a fluid-expansion-type mechanism. The increasing water production in wells on the southwest and west edges of the field indicated water encroachment from these directions, and suggests some recovery energy may be available from this source.The total probable ultimate remaining recoverable reserves have been estimated at° 332,469,000 barrels of oil. Markets have not been able to keep up with the rate of development of the medium crude re-serves. However, it is felt strongly that substantial additional markets for Weyburn medium crude will be developed by the producers in the near future at realistic wellhead prices."

Jan 1, 1959