Search Documents

By R. L. Fleischer, B. Chalmers

In order to observe size effects associated with a grain boundary, aluminum single crystals and bicrystals of various cross-sectional dimensions were deformed in tension. Typical stress-strain curves are presented in conjunction with measurements of the effects of changes in crystal dimensions. Some effects of the growth rate used in preparation of crystals are also described. It is indicated that the macroscopic constraints at a grain boundary are responsible for the most prominent grain-boundary effect, the production of multiple slip. Two measurements of the width of the region of double slip are in agreement. It is concluded that the yield stress of aluminum is affected markedly by the inherent oxide coating. THE general problem to be examined is that of dimensional effects in the plastic deformation of metal crystals. These effects will be termed "size effects" and are here defined as follows: A size effect occurs in a series of crystals if their plastic-deformation properties are a function of crystal dimensions. Clearly then size effects depend on the nature of the boundary conditions imposed on the crystal. Crystal boundaries can be of three types: interphase, inter-crystalline, and free surface. Such deformation effects as are caused by distribution of phases, grain size, lineage structure, and single crystal external geometry are specific types of size effects. This discussion will be confined primarily to grain-boundary and single-crystal size effects, though in practice most "single crystals" not only have a number of small angle boundaries but also have one or more surface phases, so that the boundary conditions appropriate to a free surface do not necessarily apply. Hence, to this extent interphase size effects will be considered. The question of size effects associated with grain boundaries (called here intercrystalline size effects)

Jan 1, 1959

By J. L. Gissy, G. H. Schippereit, J. B. Schroder

THE existence of mechanical anisotropy in hexagonal metals is well known.' One possible method of measuring the degree of anisotropy in a metal is to make hardness measurements on the different planes of a single crystal. So far as is known, no single-crystal hardness data have been reported in the literature for alpha titanium. To obtain an estimate of the variation in hardness with crystallographic direction in titanium, Knoop hardness measurements were made on single crystals of electrorefined alpha titanium obtained from the Bureau of Mines, Boulder City, Nev. The hardness of arc-melted ingots prepared from this material was 64 Bhn (1000-kg load, 30 sec). Crystals of sufficient size were mounted in epoxy resin with the basal plane exposed. They were then polished and etched to remove excess plastic resin and work-hardened surface material. The crystals were then examined by x-ray diffraction, using the back-reflection Laue technique to insure that the crystals were properly oriented and strain free. After Knoop hardness readings (100 or 200-g load) were taken on the exposed surface, the crystals were remounted to expose a prismatic face and the foregoing procedure was repeated. Hardness values for various orientations are listed in Table I. The data show a difference between the hardness of the basal planes and that of the prismatic planes, as anticipated. More striking is the hardness difference observed between different orientations of the indentor on the prismatic planes as shown in Table I and Fig. 1. All of the indentations shown in Fig. 1 were made with a 100-g load. The long axis of indentation A is parallel to the unique (c) axis of the crystal. The deformation marks visible around indentations A and C of Fig. 1 are probably slip traces of the (10.0) system reported by Rosi, et al. The greater hardness observed when the long axis of the indentor was perpendicular to the unique axis of the crystal (indention B) is probably caused by the opera-

Jan 1, 1959

By Evan Just

Government aid, regulation, and participation in the mineral industry are not new; they date back to the time when man first adopted communal living. Even in primitive tribal life, the obtaining of arrowhead or ceramic materials, washing of gold, or mining of copper were specialized activities, under tribal sponsorship. Later, when kingdoms, dynasties, and hierarchies developed, titles to mining properties were held by the sovereign or the state, work usually being done by slaves. Title acquisition through denouncement developed in Europe in the late Middle Ages and spread to the Western Hemisphere with the Spanish and Portuguese empires. Denouncements still recognized the rights of the sovereign in the requirement to pay royalties, which practice continues in many places today. Thus, anyone who views government participation in mineral activity as "encroachment" has no historical perspective. Only in a few countries and for a few generations have private interests enjoyed the right to exploit mineral deposits without the specific consent of the sovereign or without payment-of-royalty. Governments and the mineral industry have been linked together by other factors. Governments have had special interest in metals and minerals as stores of value and for armaments. Spanish conquests in the New World were energized by the lure of gold and silver. Pursuit of gold led to the American seizure of California in the days of the Forty-niners. The strategic importance of minerals in our own times has called for special steps to stimulate production in national emergencies and to prevent the enemy from acquiring mineral supplies. Our export controls to deny certain minerals to unfriendly countries, purchases for Government stockpile, and subsidies for domestic production are examples. Production regulation by state governments of oil and gas has become a well established routine. In brief, the mineral industry has never lacked aid, regulation, and participation by governments. The entrepreneur who wishes to explore for or develop minerals must deal with governments in most areas before he can begin, because mineral rights are reserved by them. He can proceed through discovery and de-

Jan 1, 1959

By W. C. Knopf, G. Samsel

For several years International Minerals & Chem-ical Corp. has used a radiation method to assay potassium content of products from potash and feldspar beneficiation. The procedure is rapid, accurate, and inexpensive and is easily handled, if necessary, by nontechnical personnel. Data are presented to show the accuracies that may be expected if the technique is used for control of pilot plants or large-scale plants. Natural potassium is composed of three isotopes —K, K and K. Five other isotopes, artificially produced, have been detected. In natural potassium only the K isotope, with a half life of 1.4x10 years, is radioactive. Its modes of decay are beta and gamma rays, positrons, and x-rays. Only the more abundant beta rays, however, are important in radiation measurements using geiger tubes. Barnes and Salley' measured radiation of potassium salts in solution in 1943. Gaudin and Parnell2 first reported the use of solid salts arranged in a vessel surrounding the ß counter in 1948. Later, Scheel used the method to assay potassium content of various crude and finished potash salts. Experimental: Dip-type Geiger-Muller tubes (TGC-5) supplied by Tracerlab Co. were used in all radiation counting measurements. The tube was encompassed by a glass container about M in. larger in diameter than the tube. This container, which served as a sample holder, was closed at the bottom with a rubber stopper to facilitate removing the samples. Samples were not weighed, but about 40 g of sample were needed for each test. Electrical impulses from the tube were counted on either a Tracerlab scaler or a rate meter. To obviate the need for constant attendance, preset features were incorporated into the scalers, so that at a predetermined time or count the units were automatically deactivated. When rate meters were used, counting rates were read directly from instrument or from a recorder used in conjunction with the rate meter. Each tube was calibrated, according to the manufacturer's instructions, to determine the correct operating voltage to insure reproducible results. A linear calibration plot of percent K2O vs counting rate was also obtained for each tube by recording the counting rate plus background count of several standards of different K2O content chemically analyzed by the chloroplatinate method.' These standards were of approximately the same particle size distribution as samples to be assayed. Specific background count caused by cosmic rays and other surrounding radiation was checked periodically by counting a sample of pure NaCl. Fig. 1 is a representative calibration plot. Assays were determined directly from the standard plot or calculated by subtracting the background count from the counting rate, then multiplying by the slope of the line. Chemical assays of the test samples were made by the Sherril method," a flame photometric technique, or the chloroplatinate method. Data: The radiation assay method has been used for three years by International Minerals & Chemical Corp. in the laboratory and in pilot plants processing ores containing potassium. These dry concentration plants process sylvinite and langbeinite ores at Carlsbad, N. M., and feldspar ores at Top-sham, Maine. Sylvinite ore is predominantly a mixture of syl-vite (impure KCl) and halite (impure NaCl). Contaminants include sulfates, such as langbeinite (2MgSO - K2SO4), kieserite (MgSO H2O), poly-halite (MgSO4.K2SO, 2CaSO, . 2H2O), and slimes. Langbeinite ore is predominantly langbeinite and halite with small amounts of sylvite, sulfates other than langbeinite, and slimes. Several variables, in addition to correct calibration and standardization of tubes, were found to be important in obtaining reproducible results. Particle size distribution of standard samples should be

Jan 1, 1959

By L. R. Shoenberger

Boron has been used to produce nonaging low-carbon sheet steel. Retention of the necessary minimum amount of about 0.006 pet partially killed the steel. Amounts exceeding about 0.012 pet increased the degree of deoxidotion, piping tendencies, and possibility of hot tearing in primary rolling. Semikilled practice resulted in good ingot yields and satisfactory surface quality. Aluminum added with the boron provided a protective de-oxidizer. Good drawobility was indicated by performances of the steel in a limited number of deep-drawing trials. Some problems with hot-tearing and boron-analysis procedures were overcome. Metal lographically, the boron semikilled steels revealed some structures not usually found in plain low-carbon steels. IN 1943 Low and Gensamer1 reported that strain aging, which hardens and embrittles ordinary low-carbon rimmed steel, was due to nitrogen and carbon, and that oxygen played a relatively unimportant role. Since then, many investigators have substantiated their findings and indicated that nitrogen is particularly potent. Commercially, today's most widely produced non-aging sheet steels for deep drawing are either aluminum killed or vanadium rimmed types. The difference in deoxidation practice, alone, is evidence that oxygen is apparently not an important consideration in control of strain aging. The fact that nitrogen is important is apparent in the consideration that has been given, knowingly or unknowingly, to the amount combined with aluminum and vanadium. Patents were granted to Hayes and Griffis2 for the processing of aluminum-killed steel, and to Epstein" for the manufacture of vanadium rimmed material. Certain prescribed steps in producing these steels can be correlated with the formation of the respective nitrides within certain temperature ranges below the usual hot-finishing temperatures. The potential nonaging properties of either type can be reduced or suppressed by cooling too rapidly to permit the aluminum or vanadium to combine with nitrogen. Subsequent suberitical annealing of the cold-rolled strip, however, normally forms the nitrides and produces the resistance to strain aging. Titanium-killed nonaging steel, described by Comstock,1 forms a nitride in the molten state and is essentially nonaging throughout its processing. Zirconium-killed steel, which was investigated briefly by the author,* appeared to have similar nitride- forming characteristics. It is known" that chromium can produce nonaging rimmed steel, but relatively little is known of the potentialities of some of the other nitride-forming elements such as boron, silicon, columbium, and cerium. In attempting to develop a new nonaging cold-rolled sheet steel with good drawability, the following factors were considered pertinent. Such a steel would necessarily have a low carbon content and therefore have a relatively high degree of oxidation when made in a basic open-hearth furnace. If the denitriding element were also a deoxidizer, a part of the addition would be lost as oxide. The degree of deoxidation would determine whether the steel is rimmed, semikilled or killed, and also could be expected to have an important bearing on ingot yields and ultimate surface quality. Assuming that the pattern for the production of cold-rolled sheets would not be changed to any great extent, the nitride must form in the molten steel, in hot rolling, in subsequent cooling, or in annealing. The nitride, once formed, should resist dissociation and be stable in the final product. Usually an excess of the nitride-forming element is required to combine with sufficient nitrogen. If the element used is a strong ferrite strengthener, a small excess may markedly decrease drawability. With aluminum and vanadium, about 0.03 to 0.05 pct in the steel is preferred. Epstein has said" that about 0.30 pct chromium is required. Titanium nonaging steels are hard unless a sufficient amount (about 0.30 pct) is added also to combine with the carbon. The cost of the necessary amounts of these latter two elements discourages commercial acceptance. Silicon was considered as a possible nitride former, but since amounts up to 0.10 pct in rimmed and semikilled steels do not induce marked resistance to strain aging, larger amounts are apparently required, which would tend to harden and strengthen the ferrite. Of the other elements mentioned, all but boron are expensive heavy-metal elements. Stoichi-ometrically, almost an equal weight of boron would be required to combine with the nitrogen—-ordinarily about 0.003 to 0.006 pct in scrap-practice open-hearth steels. Boron is a slightly stronger deoxidizer than carbon but is less powerful than zirconium, aluminum, or titanium. Thus a rimmed-steel practice might be possible. There is much in the technical literature concerning the hardenability effects of minute amounts of boron in killed steels but very little about its behavior in low-carbon material—particularly as a ferrite strengthener. The available data indicated a need for better information concerning the effects of boron in low-carbon strip steels. Experimental Work Development of a Boron-Treated Nonaging Strip Steel—Initial attempts to produce a boron-rimmed strip steel employed 3-ton basic open-hearth heats which could be teemed into molds large enough to sustain a normal rimming action. Boron as ferro-boron was added to the ladle in small amounts because of the reported hot-short character of aluminum-killed heat-treating grades containing more than about 0.005 pct boron. Actually, the amounts used, i.e., 1/8 and 1/4 lb per ton, would be large for

Jan 1, 1959

S. R. Carter (Mount Isa Mines Ltd., Mt. Isa): I found many ideas to interest me in Haddon King's paper "Notes on Ore Occurrences in Highly Metamorphosed Precambrian Rocks" (Stillwell Anniversary Volume).At Mount Isa I have not been happy about some of the longstanding appreciations of the geological evidence as fresh data accumulated, and as more and more knowledge has been building up outside Mount Isa in recent years of sedimentary deposition of sulphides.Accordingly, I organized a small section of the Geological Department at Mount Isa at the beginning of 1958 under Senior Geologist, W. J. Murray to reappraise our geological record and investigate old interpretations and new ones that arise. The work is expected to take several years to complete, but it is hoped that sufficient will be done before then to permit the most plausible story on the ore genesis to be chosen. In the meantime, W. J. Murray has proposed, in a Company Report, that the.epigenetic features of the silver,lead-zinc deposits, which are essentially conformable with the shales, could have resulted from remobilized syngenetic deposits.Haddon King, on p. 159; has listed six assumptions that are required by a magmatic-hydrothermal theory of, origin for conformable deposits. It is interesting to consider the Mount Isa silver-lead-zinc deposits in terms of these requirements.My comments are listed in the same order as Haddon King's assumptions:(a) "The source of the constituents is magmatic and they have become available in successive waves of zinc-rich, lead rich, manganese rich, silver rich, etc, instalments in accord...

Jan 1, 1959

By A. J. Nicol

Field experience in uranium has shown it is most economical to ram through a drilling program to obtain maximum footage per drill hour. Drift surveys can then determine the course of the holes. Using this method is generally cheaper than paying the additional cost involved in using the drilling technique and equipment necessary to maintain straight holes. Factors Affecting Direction of Bit Travel: In all rotary-drilled holes there is an interplay of forces or conditions affecting the direction of bit travel. Rarely is a straight vertical hole obtained. One of the major factors is weight on a drill string. In looking at a joint of drill stem it is hard to imagine its being quite flexible, but flexing of the steel increases when many joints are made up together, and even a slight weight added to the upper portion causes a buckling or spiraling effect in the hole. The result is that the bit deviates from the vertical.

Jan 1, 1959

By Carroll C. Bailey, William F. Boericke

Mine financing, or providing adequate capital for developing and bringing a mining property into production, is an essential requirement for a successful operation. Today it presents a different picture than even twenty-five years ago. The day appears to be gone when a mining property could pay its own way from grass roots to production. The country has been quite thoroughly combed for surface showings from which sufficient initial profit could be immediately garnered to pay for further development and production facilities. The four M's for success in mining-mineral, market, management, and money-are still essential; but doubled or tripled wage costs and steep advances in cost of equipment and supplies throw increased emphasis on adequate capital funds for bringing in a prospect and making it a producer. Consequently, the old picturesque, although seldom rewarding, grub- staking procedure where a single venturesome citizen might advance funds to a prospector on a fifty-fifty basis for whatever discovery he might find, has largely disappeared. Its place, to some degree, has been taken by the small syndicate of venturesome members who band together for furnishing funds to a group of prospectors for the same general purposes. Such a syndicate has a definite organization and is usually assured of sufficient initial funds, or flow of funds, to carry on work for several years. It is headed by an engineer-promoter who has had considerable field experience as well as personal knowledge of his prospecting crews. For the owner of a potential mining property who has ample capital, the problem is to determine (1) justification for the necessary investment in exploration and development, and (2) the economics of the enterprise as to size and degree of integration of the final operating entity. If the owner of such a property has little or no capital, he also faces these same basic problems but, in addition, must be able to present the findings of fact and persuade the prospective investor that the enterprise will produce

Jan 1, 1959

By W. J. Uren, Charles R. Kuzell

The industries engaged in winning minerals from the earth, because of their widespread dissemination, are faced with perhaps as wide a variety of labor-management problems as may be found in any other broad sphere of productive activity. Those problems are continually increasing in volume and complexity, and management has become aware of their growing importance. For the past quarter century at least, labor-management problems have largely been union-management problems. During this period tremendous assistance has been given labor unions through legislation and administrative and political action. In the United States, legislation favorable to unions has come about in the form of the now defunct National Industrial Recovery Act; the Wagner Act, most of which has been carried forward in the Taft-Hartley Act; the Norris-La Guardia Act; the Wage and Hour Law; the Walsh-Healey Act; and others. The result has been to transfer from the hands of management to those who direct the affairs of the unions a large share of control over the industry and to hamper in many ways the remaining control left to management. In the United States there are many examples of the power of unions to injure whole industries seriously with- out regard to the interests of management, the employes, or the public. This chapter deals with the various phases of labor-management relations as they affect the principal segments of the mineral industry in North America. To the greatest extent possible available data is presented pertaining to the unions involved, their relative strengths, labor law, compensation and fringe benefits of employes, working conditions, and related matters. As background, the historical development of union-management relations in the respective segments is included where possible. The section dealing with the United States has been divided into separate

Jan 1, 1959

By W. E. Bonini, E. A. Hickok

IN the course of an investigation directed toward expanding ground-water facilities in Essex and Morris counties, New Jersey, the Board of Water Commissioners of the city of East Orange authorized a seismic-refraction survey' for the purpose of de-lineating bedrock topography below unconsolidated overburden. Results of the survey were highly satisfactory and led to the preparation of a comparatively detailed bedrock contour map. Knowledge of the bedrock depth and configuration was an important aid in selection of sites for test drilling. The portion of the East Orange Water Reserve under consideration is in the flood plain of the Pas-saic River about 10 miles west of Newark, N. J. The flood plain is about 175 ft above mean sea level and is bordered by low hills rising to elevations of approximately 250 ft. The bedrock underlying the Water Reserve consists of sandstone and shale of the Triassic Brunswick formation and is covered everywhere by deposits of unconsolidated glacial outwash sand and gravel, lacustrine clay, and recent river silt as much as 150 ft thick. Yield of wells in the sandstone and shale averages 100 to 200 gpm. Since production wells constructed in the sand and gravel aquifer in the buried river valley shown on the contour map (Fig. 1) yield 300 to 1400 gpm, it was proposed to locate additional production wells in this buried valley, where the yields per well would be maximum. In 1939 and 1946 the East Orange Water Dept. had electrical-resistivity surveys made to determine depths to bedrock. From the resistivity data the exploration company prepared a bedrock contour map. A well field expansion program begun in 1955 utilized this information to locate sites for test wells along a predicted northward extension of the buried valley in which existing production wells are located. After several test wells (wells 201-205) had been drilled, it became apparent that the resistivity information was unreliable." For example, test well 201 recorded bedrock at a depth of 72 ft, whereas the resistivity depth determination was 130 ft. As a consequence, the test drilling program was temporarily suspended and a seismic survey was under- taken to determine the topography and extent of the buried valley known from well records to underlie the existing well field. In the first phase of this study, several seismic shot point locations were placed at sites where well logs had been obtained previously. This procedure is necessary in a new area to determine whether the seismic method is applicable and what degree of accuracy is to be expected. At the East Orange Water Reserve, depths obtained from the shot points near test wells 202, 203, and 204 were within 8 to 11 pct of the depths logged (Table I). With this assurance that accurate results could be obtained, additional seismic spreads were located on the Water Reserve. Using a portable refraction seismograph, in the fall of 1955 a crew of four men shot a total of 29 reversed seismic spreads in a period equivalent to six field days. Charges as heavy as 3 1b of 40 pct dynamite were necessary at a few places to overcome ground vibrations caused by traffic on nearby highways. At most other sites, a 1-1b charge was sufficient. Travel-time plots were made for all spreads, and depths and true velocities were calculated according to formulas for multiple sloping layers by Ewing, Woollard, and Vine.' The plot of spread 7 (Fig. 2) is typical of the short spreads in which bedrock was shallow—about 50 ft in this case. Where there were not enough arrivals through the bedrock to define the high velocity bedrock line, the spreads were lengthened. This was done by placing shots on line several hundred feet away from each end of the line of geophones. It was then possible to construct complete reverse plots for both short and extended shot points (see spread 27, Fig. 3). Four individual depths were calculated from each extended spread. Three and in some cases four seismic layers were observed. The surficial layer had a velocity range of 900 to 1200 fps, the lowest velocity recorded. This seismic layer is above the water table and is interpreted as recent river silt. The bedrock had the highest velocities, which ranged from 10,600 to 16,400 fps. Intermediate velocities ranged from 4500 to 6800 fps. In every case the intermediate layer was within

Jan 1, 1959

By C. Kolm, E. P. Warekois, S. A. Kulin

MUCH insight has been gained into the nature of the cold-worked state of metals in recent years through the use of modern X-ray techniques. These methods have revealed the existence of stacking faults together with regions of high internal strain and have provided means of measuring the atomic perturbations in plastically deformed metals. In view of the recent increased interest in the solid state, it is desirable to extend these techniques to the study of lattice imperfections introduced into semiconductors during plastic deformation. It is of particular interest to compare the state of imperfection sustained by metallic bonding with that sustained by the covalent bonding found in semiconductors. A knowledge of the imperfections which can exist in semiconductors is important from both a theoretical and a practical point of view since they can greatly influence many of the physical properties. In order to determine the possible existence of stacking faults in covalently bonded structures, precise measurements were made of the diffracted peak positions of plastically deformed germanium, gallium antimonide, and indium antimonide. These measurements were based on the theoretical treatment of Paterson1 and are similar to those employed by Warren and warekois2 in their studies of deformed a brass. In addition, diffraction peak profiles were measured on the annealed and plastically deformed materials in order to obtain information concerning the distribution of internal strains through the use of the Fourier methods developed by Warren and Averbach.3 EXPERIMENTAL PROCEDURES AND TECHNIQUES Because of the room-temperature brittleness of the semiconductors studied, it was necessary to plastically deform the materials at elevated temperatures. The brittle-ductile transition temperature ranges of GaSb and InSb are sufficiently low to permit hot-filing operations. Therefore, high-purity, polycrystalline GaSb and InSb were filed in an argon atmosphere at 400' and 300°C, respec-

Jan 1, 1959

By W. L. McMorris, A. H. Brisse

IN the last several years the coal industry has intensified its effort to solve the growing problem of cleaning and recovering fine mesh coals. On one hand these has been increasing civic pressure for cleaner streams, and on the other hand there has been increasing production of fine mesh coal, resulting directly from adoption of the modern mining methods so essential to the economy of the coal mining industry. Cleaning fine coal with the same precision possible with coarser coals is a difficult task, and for coals finer than 200 mesh it has been impractical. Furthermore, the inclusion of —200 mesh material in the final product markedly increases costs of de-watering and thermal drying, which are necessary steps if coal is to meet market requirements. Consequently these extreme fines have generally been wasted. As a result, problems have been created in many districts because there has not been enough area for adequate settling basins. Wasting of coal in the -200 mesh slimes may account for a loss in washer yield equivalent to 2.0 to 2.5 pct of the raw coal input. With rising mining costs the value of such a loss is constantly increasing and a need for a better solution to the fines problem becomes more pressing every day. From an operating viewpoint, also, continuous removal of extreme fines from the washing plant circuit permits good water clarification practice, improving significantly the overall cleaning efficiency. The obvious desirability of recovering a commercially acceptable coal from washery slimes prompted U. S. Steel Corp. to investigate the merits of the Convertol process developed in Germany." Although this process has been used commercially in Europe for some time, little if any consideration has been given to its possible adoption in the U. S. until very recently. Fundamentals of the Convertol Process: In the Convertol process, droplets of dispersed oil are brought into intimate contact with the solids suspended in the coal slurry to be treated. This contact causes oil to displace the water on the surface of the coal by preferential wetting, or phase inversion, after which the coal particles are allowed to agglomerate in a manner permitting their re- moval from the slurry by centrifugal filtration. The clay and other particles of mineral matter suspended in the slurry do not have the affinity for oil the coal particles have. Consequently the oil treatment is preferential to coal to the extent that more than 95 pct of the oil used reports with the clean coal recovered. Figs. 1 through 3 will clarify the steps involved in the process. Fig. 1 shows the suspended material in the slurry to be treated, which is a thickened product containing 40 to 45 pct solids. Oil is now injected into the slurry under vigorous agitation to produce good oil to coal contact conditions, which result in preferential oiling of the coal particles. These coal particles are then permitted to agglomerate by gentle stirring in a conditioner to form flocs, as shown in Fig. 2. At this point in the process the agglomerated oiled coal can be washed and partially dewatered on a vibrating screen, as shown in Fig. 3. Finally, the washed flocculate can be further dewatered in a high-speed screen basket centrifuge or in a solid bowl centrifuge. Commercial Application of the Convertol Process in Germany: The original Convertol process was developed by Bergwerksverband zur Verwertung von Schutzrechten der Kohlentechnik, G.m.b.H., a German research organization controlled by the Coal Operators Assn. of the Ruhr Valley. The process as reduced to commercial practice in Germany' is shown in Fig. 4. In this process a thickened slurry (40 to 45 pct solids) mixed with a predetermined percentage of oil is fed from a surge tank to the phase inversion mill. After the phase inversion step, the slurry is usually discharged directly to a highspeed screen centrifuge. From 3 to 10 pct oil is used, depending on type of oil, size consist of coal to be recovered, and operating temperature. The top size of fine coal cleaned in Germany by the Convertol process is limited by the size of the openings in the centrifuge screen basket. Any mineral matter coarser than the basket opening, which is generally 60 to 80 mesh, must remain with the oiled coal. If the coal fines have been effectively cleaned down to about 80 mesh, the cleaning performance of the process is practically unaffected by the presence of coarse coal particles. However, since recovery of coal much coarser than 80 mesh is mow economical by conventional methods, it normally becomes more costly to allow substantial percentages of this coarse coal in Convertol process feed. Where the general plant layout does not permit effective cleaning of coal sizes down to 80 mesh or lower. there is some justification for a coarser Con-

Jan 1, 1959

By F. C. Langenberg, J. Chipman

Jan 1, 1959

By Donald Mc Laughlin

El presente texto revisa los antecedentes y la capacidad metalúrgica para la instalación de una planta de fundición. Para ello, se revisa la fuerza metalúrgica, coke metalúrgico, inversiones, mano, capital de trabajo, producción y rendimientos, balance económico, efectos de las fluctuaciones de precios en el balance, económico financiación, fertilizantes y ventajas de la central metalúrgica.

Jan 1, 1959

By C. A. Bruch, J. F. Duffey

On the basis of metallographic and cooling-rate studies of 15 U-Zr alloys, a new version of the 6 phase region of the U-Zr phase diagram is proposed. IN several published diagrams of U-Zr alloy system:' there is good agreement that at elevated temperatures complete solid solubility exists between y uranium and ß zirconium. Similarly, there is reasonably good agreement concerning the uranium-rich and zirconium-rich ends of the diagram. However, there is no agreement concerning the nature of the diagram at intermediate compositions and at temperatures below about 650°C. The early work of Saller et al.8 hows an intermediate phase, 6. In a later diagram by Saller and Rough' shown in Fig. 1, the d phase field is drawn with dotted lines, indicating doubt that this phase exists. The diagram of Summers-Smith2 does not show the d phase. More recently Holden and Seymour' have shown that in the composition range 40 to 60 wt pet Zr, the high-temperature ? phase, which is body-cen-tered-cubic, transforms to an ordered structure, 8. They found that the order-disorder transformation occurs between 595° and 610°C, and presented a diagram based on the study of four different alloy compositions. Most recently Saller et a1.5 presented a new diagram which differs with respect to the composition limits of the 8 field from the others proposed by these authors. The purpose of the present investigation was to determine the boundaries of the d phase field. Experimental Procedures and Results Alloys—Buttons, weighing 80 g of 15 different alloy compositions were prepared by arc melting Mal-linckrodt uranium and iodide-process zirconium in a water-cooled crucible. A controlled atmosphere of argon and helium was maintained in the furnace. Prior to making each button, a sacrificial button of zirconium was melted to increase the purity of the furnace atmosphere. Each alloy was then melted six times to improve its homogeneity. Subsequently the alloy buttons were jacketed in copper and hot rolled to slabs at 775°C. From these slabs, specimens were machined for chemical, thermal, and metallographic analyses, Table I gives both the estimated chemical composition of the alloys, and the values which were obtained by analysis. The oxygen contents varied from 0.013 to 0.032 pet, nitrogen from 0.0014 to 0.014 pet, and carbon from 0.0013 to 0.011 pet. The purity of the alloys ranged from 99.947 to 99.975 pet. Thermal Analysis—The specimens for thermal analysis were blocks 11/4 x 1/4 x % in. The bead of a calibrated thermocouple was placed between two of these blocks and molybdenum wire was wrapped around the assembly. Each assembly was sealed in a quartz capsule having an argon atmosphere. The capsule was placed inside a refractory crucible which was heated in a furnace. Using a method described by Smith,' the emf of a differential thermocouple, with junctions inside and outside of the refractory crucible, was used to activate the

Jan 1, 1959

By M. E. Wadsworth, T. L. MacKay

Sintered UO, samples were leached in sulfuric acid solutions of various concentrations. A pressurized system was used so that it was possible to investigate the kinetics of the reaction to 270°C with oxygen overpressures as high as 900 psi. The rate was observed to be a function of the concentration of hydrogen ions and directly proportional to the partial pressure of oxygen. Evidences are presented which indicate that a UO2 surface site reacts with a molecule of water to form a hydroxyl complex which in turn can dissociate with the characteristics of a weak acid. A rate determining step has been proposed which involves the reaction between an oxygen molecule and the hydroxyl complex on the surface of UO,. ThE 2 principal methods for uranium dissolution are carbonate and acid leaching. The sulfuric acid leach is the more popular and is used for the treatment of the majority of the ores of Africa, Canada, and the United States. Low recoveries in basic leach circuits led investigators at the University of British columbia1 to study leaching of uranium ores in pressurized vessels. Early in the study of dissolution of uranium it was found that only uranium in the hexava-lent state could be leached in acid or basic circuits. Therefore, the use of oxygen over-pressure in an autoclave offered an interesting approach to solving the low recovery problems of carbonate leaching. UO, was used in this study because it could be obtained in high purity and also because it is representative of the most refractory of the primary uranium minerals. A pressurized system was used to provide a means whereby important temperature and pressure parameters could be varied for the evaluation of the kinetic processes. The mechanism for the dissolution of UO2 should be similar for any of the uraninite type minerals. At the present all of the kinetic studies that have been conducted have been in carbonate media. Peters and Halpern2 carried out a kinetic study of the leaching of pitchblende. Their specimens were pitchblende ores selected on the basis of high grade and homogeneity. Pearson and wadsworth3 conducted a kinetic study of the dissolution of UO2 in carbonate solutions with results very similar to those obtained by Peters and Halpern. EXPERIMENTAL The UO2 as received* was found by spectroscopic *Mallinckrodt reagent, supplied by the Atomic Energy Commission. analysis to have a purity of 99.94 pct 0.03. It was ground in a mechanical agate mortar and screened through a 400-mesh sieve. Thin flat disks of UO2 were prepared by pressing the sized powder in a specially constructed die at a total pressure of approximately 25 tons per sq in. The pressed disks were approximately 0.25 cm thick, 1.6 cm diam, and 3.5 g in weight. As pressed, the samples were approximately 65 pct of theoretical density. It was essential that a binder such as poly-vinyl alcohol be added before pressing to prevent formation of cracks when fired. It was found by trial and error that pressed disks sintered close to 1870°C in a hydrogen atmosphere, reach densities between 91 and 91.5 pct of the theoretical density. At this density the samples had no measurable porosity based upon a 2-hr emersion in boiling water. An X-ray examination of these sintered UO2 disks showed them to be identical with the original UO2 received. Reaction of UO2 with the alundum furnace core was prevented by placing molybdenum between the samples and the core according to the method of Corwin and Eyerly.4 Leaching studies were carried out in a specially designed autoclave, the details of which have been presented e1sewhere.6 The main features of the equipment as applied to a kinetic study are: 1) solution samples may be removed during the course of a single run; and 2) temperature and agitation are carefully controlled. Two-ml samples removed from the autoclave during the course of a run were analyzed for U3O8 content with a Beckman model DK-2 spectrophotometer by the method of

Jan 1, 1959

By Rudolph G. Wuerker

WITH the growing complexity of ore dressing processes and the diversity of equipment, efficiency control has become increasingly important in beneficiation. In the case of iron ore dressing, there have been sporadic attempts'-3 to establish the optimum separation for various ores so that grade and recovery would be readily predictable. But no rigorous statistical analysis and graphical presenta- tion of such tests could be found in the literature of this country. Tests Made with Iron Ores Expanding upon existing methods of plant supervision and efficiency control, an investigation was started in the ore dressing laboratory at the University of Illinois on the applicability of distribution analysis to iron ores. A sample of crude ore was obtained from the Ohio mine of Cleveland-Cliffs Iron Co. at Ishpeming, Mich., consisting mostly of alternating bands of hematite and siliceous gangue, both about 1/4 in. wide. The ore was heavily coated with limonite, which often filled the cracks.

Jan 1, 1959

By S. Yamaguchi

IN this study of thorium and uranium minerals an x-ray shadow microscope of the Cosslett type1 was used. A flux of electrons driven with a voltage

Jan 1, 1959

By H. W. Weart, D. J. Mack

SINCE the first recognition of eutectic solidification as the simultaneous formation of 2 solids from one liquid,1 many complex structures thus produced have been observed. Despite many attempts to ascertain it, however, the detailed mechanism by which these structures develop remains obscure. In an attempt to clarify the origin of eutectic structures, the study described in this paper was undertaken. The broad objective of the study was to investigate the effect of different solidification conditions on the structure of single eutectic grains. It was expected that the eutectic structure would thereby be isolated for study, but preliminary experiments revealed another structure within each grain. When a literature surveye revealed only 1 previous mention of the subgrain structure,' it was decided to determine the origin of the structure and to study its response to various growth conditions. Before presenting the details of the investigation, it is apropos to distinguish carefully among the 3 structures produced during eutectic solidification. This is especially desirable in view of the apparent confusion existing in the literature concerning the structures in a eutectic specimen. The confusion is due largely to the existence of the subgrain structure noted above which is easily mistaken for the grain structure. In the following paragraphs, an effort is made to distinguish the 3 structures by briefly describing their origin during solidification, even though the results are thereby anticipated slightly. The 3 structures produced during eutectic solidification are the grain structure, the colony structure, and the eutectic structure, each one contained by the one preceding it. The grain structure is analogous to the polycrystalline structure of a metal or inle-phase alloy in that each grain grows from a single nucleus. A somewhat broader interpretation is needed here, however, because of the presence of 2 phases in each grain. Since in most eutec-tics particles of 1 phase are dispersed in a matrix of the other, a grain may be taken to be the region in which the matrix phase is monocrystalline.*

Jan 1, 1959

By C. G. Dunn, P. K. Koh

Microstructure, magnetic torque, and texture data before and after grain growth were obtained on two 3.25 pet Si-Fe specimens having initially the same cold-rolled textures and the same primary recrystallization textures. The latter textures consisted of four components, two only of which were strong; the strong components were near (120) [001] and (320) [001]. The textures of the two specimens obtained by grain growth were different. In one specimen the two weak components were converted into strong components by a secondary recrystallization process; in the other specimen the primary recrystallization texture was retained by a normal grain-growth process. The difference in behavior of the two specimens was interpreted in terms of a difference in the relative grain sizes between weak and strong components; i.e., in terms of a geometrical factor that would alter the early growth rates of grains belonging to the two weak components of the texture. Specifically the growth rate was considered as the product of two terms: a driving force and a boundary mobility. The texture changes observed are considered to favor the oriented-nucleation growth-selectivity theory more than the oriented-growth theory. WHEN primary recrystallization and grain-growth textures form as a result of annealing deformed metals or alloys, the fundamental processes involved are nucleation and growth. Knowledge, therefore, about nuclei and the factors influencing their growth is required not only for the understanding of texture development but also for its control. In the oriented-growth theory of texture formation1, 2, 3 the problem of nuclei is generally disposed of by the assumption that nuclei are available in all orientations; the theory then has to explain the final texture from the initial texture and the way boundary mobility depends on orientation. In the oriented nucleation theory of texture formation"' nuclei are considered to be present only in certain orientations but the importance of growth selectivity is still recognized. For example, the mobility of boundaries of approximately the same orientation and of the coherent type in twins is believed to be low while that of high-angle boundaries, in general, is high. Because of this the theory may be described as an oriented-nucleation growth-selectivity theory. The main feature of the oriented-nucleation theory, however, is the importance given to nuclei; i.e., how they form in specific orientations and how they grow. In the present investigation two cold-rolled single crystals were used to study the effects of growth after primary recrystallization. The cold-rolled textures and the primary recrystallization textures were determined from portions of these specimens and reported earlier.",' The two cold-rolled crystals were in the (111) [112] stable end orientation, the recrystallization textures were nearly identical and consisted of two strong components, designated M and M', which were near (120) [00l] and (320) [00l], respectively, and also some specific weak components near (111) [110] and (111) [110]. It is well recognized that a single strong component in the primary recrystallization texture may be needed for secondary recrystallization3, 5, 8 but unfortunately when this is the case the amount of material left in deviating orientation may be too small either for growth or for positive identification. The present samples proved to be almost ideal for the study of minor components and their influence on texture changes produced by growth after primary recrystallization. The results obtained are interpreted in terms of present knowledge of grain-growth processes. Experimental Procedure Two lots of silicon-iron alloy of essentially the same composition, namely, 3.25 pet Si, 0.004 C, 0.009 P, 0.010 S, 0.035 Mn, 0.070 Ni, 0.090 Cu, 0.009 Sn, with traces of A1 and Cr and the balance Fe, were converted into single crystals 0.025 in. thick and 1.25 in. wide. The orientations were predetermined by the method of reorienting a seed crystal as described elsewhere.3 pecimen 1 from one lot had the (335) [556] orientation while specimen 2 from the second lot had the (111) [112] orientation.* Both crystals were cold rolled to a reduction in thickness of 70 pet while widening approximately 20 pet. Samples of each were selected for determining 1) the cold-rolled texture, 2) the time required at

Jan 1, 1959