Search Documents

By G. R. Webber

CHEMICAL AN AL YSIS by x-ray emission spectrometry has become increasingly important during the past few years. The method is analogous to optical spectrography ?with x-rays being used instead of light and should not be confused with methods of x-ray diffraction used? for identification of minerals and chemical compounds. X-ray emission spectrometry has many advantages for both qualitative and quantitative analysis. Its optimum concentration range is higher than that of the optical spectrograph, and the group of elements which can be detected is not identical to that which can be detected by the optical spectrograph. Elements which can be detected by the x-ray spectrometer are those elements from magnesium (atomic number 12) to uranium (atomic number 92) in the periodic table. The lightest elements in this range have low sensitivities and more specialized equipment is necessary for their detection than for the heavier elements. A large number of applications of x-ray analysis have been directed toward the analysis of ores, metallurgical products, and related materials (see References at end of paper). A more complete bibliography is presented in the Norelco Reporter, Vol. 3, 1956, pp. 37-39. The periodicals Analytical Chemistry and Applied Spectroscopy are a good source of current articles and references.

Jan 1, 1957

By W. A. White

UNDERCLAY squeeze is the plastic flowing of underclay below coal pillars into mined-out entries and rooms. Squeezes may be caused either by wet mine conditions where the moisture is taken up by the clay—making it more plastic—or by the presence of certain clay minerals, such as mont-morillonite, which are plastic when there is enough natural moisture. Under either condition, sufficient stress will cause the underclay to flow. Squeezes may fill an entry or room within several hours, or it may be several months before movement stops. Squeeze areas commonly cover hundreds or thousands of square yards. The Coal Div. of the Illinois State Geological Survey has collected samples of underclays from various mines and from cores drilled by coal companies in the state. From these samples natural moisture content, particle size and particle size distribution, and clay mineralogy are determined. Data from samples collected from the underclay below Herrin (No. 6) coal in the Lumaghi Coal Co. mine near Collinsville, Ill., are used in this report to clarify points in the discussion. Data from samples taken from other mines lead to the same conclusions. A generalized geological section for the area is given in Table I. The underclay below coal No. 6 ranges from a few inches to 3 or 4 ft thick. The upper 6 to 18 in. are noncalcareous; the lower part becomes more calcareous with depth. Limestone nodules become larger with depth, almost grading into the limestone below. In areas where the clay is nearly absent the limestone may thicken to take its place; thus they may complement each other in thickness. There are two types of squeeze areas in a mine. In one type up to 3 or 4 ft of underclay lie in what appears to be a depression in the limestone underneath. This is suggested by a rim surrounding the squeeze area where the underclay is thin and the limestone lies within a few inches of the coal. In the second type the underclay of the squeeze area is surrounded by underclay of similar thicknesses which does not squeeze. Test Methods: Natural moisture content, particle size and particle size distribution, and clay mineralogy were determined by the following methods: Natural moisture is the moisture content a clay contains in its natural environment, expressed in percentage of the weight of ovendried clay (110°C or 230°F). To obtain the natural moisture content, given in Table 11, the clay samples were sealed in containers as soon as the samples were taken in the mines. Particle size and particle size distribution were determined by the pipette method,' and the data were plotted as cumulative curves, Fig. 1, on semi-logarithmic paper. Particle size was plotted on the logarithmic scale and percentage on the arithmetic scale. The quartiles (diameters that correspond to frequencies of 25 and 75 pct) and medians (diameters that correspond to the frequency of 50 pct) of the samples were determined from these curves. The clay minerals were identified from the data obtained by differential thermal' and X-ray powder" techniques. The differential thermal analyses were made on the whole samples, whereas the X-ray analyses were made on fractions of less than 2p. Data and Discussion Moisture Content: After the sealed jars had stood for 24 hr, those that contained squeeze samples had perspired, so that droplets of water had accumulated on the insides of the jars. Table II shows the moisture in the clay after it had perspired for 24 hr. (This perspiring was not noted in samples from nonsqueeze areas.) After perspiration one of the squeeze samples still had a higher moisture content than the samples that did not squeeze. Clay Mineralogy: The thermal analysis, Figs. 2 and 3, indicates that the clay minerals are chiefly micaceous in type; the low-temperature endothermal

Jan 1, 1957

REJUVENATED is an apt word to apply to Chino, Kennecott's big open-pit mine at Santa Rita, New Mexico. Back in 1923 Chino was merged with Ray by an exchange of shares, and in 1926 the Ray-Chino combination was taken over by Nevada Consolidated through an issue of bonds that were traded for the Ray and Chino assets. Subsequently, of course, the whole package was acquired by the Kennecott Copper Corporation. On the basis of the terms of the Ray-Chino-Nevada exchanges, Chino was rated third in value, something less than thirty per cent of the total. In 1955 the appraisal would doubtless be forty per cent or more. But it is not only vis-a-vis Ray and Nevada that Chino has blossomed out. At the end of 1931, Chino ranked seventh among the Porphyries in point of output; whereas by the end of 1954 it was fifth,. having passed both Inspiration and Nevada Consolidated. Sharp curtailment in production in 1932-33-34 and total suspension in the two years following (see Fig. 21) found the property in a somewhat parlous position. However, the engineers had not been idle; they had been planning for the future, and in 1937 a far-reaching program of rejuvenation was launched. During the ensuing five years, capital expenditures totaled more than $8,500,000. Among the projects undertaken were the following: (1) Mine-Purchase of larger and better equipment for drilling, loading, and transporting the ore. (2) Mine-Beginning of the first systematic project to leach and recover copper in the waste dumps at the mine.

Jan 1, 1957

The first metal-mine accident-prevention course was prepared and published in 1942-45 as a series of seven miners' circulars (Nos. 51-57). The scope of the course has been broadened, revised, and brought up to date and is being published as a similar series of seven miners' circulars (Nos. 51-57, revised) on accident prevention in metal and nonmetallic mines. These circulars are: Accident Statistics (Miners' Circular 51), dealing with general statistics on accidents and injuries at metal and nonmetallic mines, including causes, costs, and the use of investigations and reports of all accidents.

Jan 1, 1957

By H. R. Brannon, J. S. Osoba

The introduction of the scintillation counter into field use for gamma-ray well logging has provided a new tool with special utility for the deternzination of natural radioactivity of sediments. Previous subsurface gamma-ray measurements have indicated only the total amount of radioactivity of the sediments. With the scintillation counter, the relative amounts of the elements which emit gamma radiation can be determined. Sediments logged included 35 zones in wells located in the Teras Gulf Coast, East Texas, and West Teras. Although the data obtained from measurements made to date are not sufficient to evaluate the possibilities of spectral logging, it appears likely that spectral measurements will yield information of geologic value. INTRODUCTION Although variations in the natural radioactivity of sediments were recognized as early as 1909,1 the appli- cation of such variations to borehole logging was not made until almost 30 years later. A group of Russian workers in the early 1930's were successful in making crude measurements of natural gamma activity in an oil well borehole. The first practical gamma-ray logging system was developed by Howell and Frosch2 in 1939. Induced radioactivity, or neutron, logging appeared soon after the introduction of gamma-ray logging. After early work had demonstrated the potentialities of radioactivity logging, development of sensitive and stable logging equipment for field use followed, so that neutron and natural gamma logs are now run routinely and have proved to be extremely valuable in characterizing subsurface formations. Even though tremendous strides have been made in developing radioactivity logging, it is apparent that the ultimate in the method of logging has not been reached, for, until very recently1 in none of the commercially available logging systems has advantage been taken of the fact that gamma radiation is composed of a spectrum of rays, each ray having a distinct and characteristic energy. An individual gamma ray originates in a single element and has energy determined by the element. The inten- sity of radiation, or number of rays emitted from unit volume in unit time, is determined by the concentration of the element. If it were possible to sort out these gamma rays and assign them to their parent elements, thereby essentially analyzing for the elements, a wealth of new information descriptive of formation material and fluid content would be at hand. For example, if in natural gamma logging, the gammas due to potassium and to the thorium and uranium series were measured individually, data would thus be available on the concentrations of each of the three elements, adding materially to the information content of the log. In contrast, conventional gamma logs measure only a quantity proportional to the combined concentrations of uranium, thorium, and potassium. The naturally radioactive elements occur in sediments in concentrations dependent on source material of the sediment, and through their chemical characteristics, on conditions of deposition,' so that the individual concentrations may be diagnostic for particular formations. These concentrations, particularly if measured in situ, could lead to a powerful tool for correlation and for reflecting environmental conditions under which sedimentation took place. As a correlation tool, individual uranium, thorium, and potassium measurements

Jan 1, 1957

By G. G. Eichholz

SUMMARY RADIOACTIVE dynamite has been prepared by introducing a small amount of antimony-124 into the explosive. Test work is described on the effectiveness of this tracer, on radiation levels in its neighbourhood, and on different methods of .application. Factors determining the choice of isotope, amount of activity, and overall cost of this process are discussed. INTRODUCTION Instances are known in which dynamite remains unexploded in drill holes in mining operations. Usually such 'bootlegs' are easily located by inspection of the face and the powder is removed before subsequent drilling is started. Occasionally, however, serious accidents occur because workmen drill into an undetected piece of dynamite. In order to avoid such accidents it was suggested that a different method of location might be tied, such as that afforded by the use of radioactive tracers. This paper describes some experiments that were carried out under the auspices of the Department of Mines and Technical Surveys, with the active co-operation of Canadian Industries Ltd. and Canadian Refractories Ltd., to test the feasibility of such a scheme.

Jan 1, 1957

If lead buttons are cupelled under closely controlled conditions in a suitable design of furnace, silver losses during cupellation are given by a simple equation. The effect of copper on these silver losses has been studied and a "copper limit" for cupellation has been determined. Scorification and crucible fusion procedures for copper-bearing materials have been designed so that the lead buttons produced will not contain amounts of copper greater than this determined copper limit. Silver losses during these crucible fusion and scorification procedures are given by the distribution law, and can be calculated. Thus, silver can be determined in copper-bearing materials with a satisfactory degree of accuracy provided that the appropriate corrections for losses are applied to the weight of the silver prill produced.

Jan 1, 1957

By T. R. Jolley

An investigation was begun by the Bureau of Mines in 1948 to determine the preparation characteristics of American coals. Results of the investigation were planned to be reported on a county basis and, from the data developed, to determine: I. Which coals either as mined or after beneficiation by conventional preparation are chemically suitable under present standards for producing metallurgical coke. 2. Which coals require special and more intensive treatment in preparation than is now practiced. 3. Which coals cannot be considered potential sources of metallurgical coke, regardless of preparation by present-day methods. This report is one in the county series that describes the preparation characteristics of the coals of Bell County, Ky.

Jan 1, 1957

By S. C. Sun, D. R. Mitchell

T LTRASONICS can be used to deslime and up-grade ores, such as tungsten and tin, which slime excessively with high losses of value in the tailing and are difficult to deslime with conventional methods. Experimenta] work has been performed with a test-tube size ultrasonic classifier. Larger equip-

Jan 1, 1957

By F. R. Cattoir

Analytical methods are presented in this paper for determining soluble titanium, total titanium, indicated titanium, and average effective valence in titanium chloride - sodium chloride mixtures. In addition, data are given showing the effects of coarse and fine grinding on the degree of oxidation and average effective valence of such samples. INTRODUCTION The Electrometallurgical Experiment Station at Boulder City, Nev., as part of the Bureau of Mines program to obtain more efficient utilization of our natural resources, has been developing and improving titanium extractive metallurgical methods and techniques since 1945. Numerous reports have been published describing development of the Kroll process,4/ the electrorefining technique,5/ and methods of analyzing titanium sponge.6/

Jan 1, 1957

Brief descriptions of several types of unit pulverizeI' are given and the functioning of the components that crush, carry, dry and classify the coal is considered. A distinction is drawn between pulverizers which crush particle beds and those .operating by free-crushing. The overall performance of pulverijlers is considered in terms of correlations between mill variables, coal grindability, abrasiveness, moisture and particle size. Brief discussioiJ. of the influence of pulverized fuel quality on boiler operation and of pulverizing costs concludes the paper.INTRODUCTIONModern coal pulverizers function as carriers of materials and as crushers, as dryers and as size classification machines and, thus, the unit pulverizer comprises. several components that normally function as separate apparatus. The controls of the unit pulverizer must have sufficient flexibility to accommodate rapid variations of boiler load or coal quality. Further, the machine must be robust, yet easy to maintain preferably at annual intervals-so that maintenance costs are small (for coal is a relatively cheap material). Usually, the full load of a modern pulverized-fuel fired boiler can be raised with one pulverizer off-line. All coals, from anthracites to brown coal, may be prepared as pulverized fuel (hereafter P.F.) .Each pulverizer of a direct-fired boiler has, broadly, to supply the burners with coal powdered so that about 80 per cent passes a 200 B.S. sieve and only a small proportion, less than about 10 per cent, remains on the 100 B.S. sieve. The classification processes must prevent any appreciable proportion of coarse particles in the P.F. and yet not return excessive proportions of "finished" fines. The quality of the P.F. should not vary greatly with output rates which may be anywhere between the maximum rate and one quarter ofthe maximum. The suspension of P.F. in the primary air...

Jan 1, 1957

By K. O. J. Sidwell

STRATMAT LIMITED, through its subsidiary, the Strategic Manganese Corporation, controls two adjoining iron-manganese properties five miles west of Woodstock, New Brunswick. One is a staked property of 77 claims traversed by one trunk highway, several secondary roads, and a branch line of the Canadian National railway. The other property, a 20-square-mile Concession immediately to the north-east, is also traversed by an excellent network of roads. Both proper-ties are situated in gently rolling farmland. The deposits were discovered in 1836 by Dr. C. T. Jackson. The first attempt to exploit them was made in 1848 when a blast furnace was erected with a capacity of 7 tons per day. The ore was mined by a series of deep trenches that followed the folds of the enclosing slates. In the late years of operation, bog iron ore from Burton and Maugerville, in Sunbury county, was used in conjunction with the Wood-stock ore. An additional 5-ton furnace was erected in 1863 and mining was carried on intermittently until 1884. No further extensive work was done until 1953. During the period of activity, approximately 70,-000 tons of ore are said to have been smelted ( 1). During these earl y operations the Iron Ore Hill and Moody Hill deposits were partially opened, with the ?bulk of the furnace feed being mined from the Iron Ore Hill workings. The low tenor and apparently limited extent of the deposits, the high. ?content of phosphorus, and the increasing scarcity of fuel, were the chief factors that brought the enterprise to an end.

Jan 1, 1957

By Henry A. Wriedt, John Chipman

Equilibrium in the reaction of hydrogen gas with oxygen in liquid nickel, iron, and their alloys has been studied at temperatures of 1500° to 1700°C. The equilibrium con^stant, 0/p, [% O], is greater in nickel then in iron by a factor of 45 at 1594 C. In the alloy steel range, the activity coefficient of oxygen is slightly increased by the presence of nickel. NICKEL is more resistant to oxidation than is iron, in both the solid and the liquid state. The solubility of oxygen,' however, is greater in nickel than in iron. The two metals and their liquid alloys constitute an interesting series of solvents in which the chemical behavior of oxygen can be studied by methods similar to those used for liquid iron.' Experimental Method The furnace assembly, including the tube for preheating the entrant gas, was the same as that described by Gokcen and Chipman. " controlled mixture of water vapor, hydrogen, and argon preheated to approximately the melt temperature impinged upon the surface of the liquid metal. The charge, weighing about 35 g, was held in an alumina crucible at constant temperature in the gas stream for a prolonged period, then quenched in a stream of cold helium, sampled, and analyzed for oxygen by the vacuum fusion method. The temperature of the liquid metal was measured by a Leeds and Northrup optical pyrometer which had been checked against a similar instrument certified by the National Bureau of Standards. The freezing point of electrolytic iron in hydrogen, taken as 153j°C, was used for frequent checks. This point and the emissivity determined by Dastur and Gokcen" established the transmissivity of the optical system. The emissivities of Fe-Ni alloys at 1535" are known from the experiments of Smith and Chipman,h nd it was assumed that the variation with temperature is parallel with that of iron. Recorded temperatures are probably accurate within k5"C. Preparation of Gas Mixtures—Since the ratio H,O:H, had to be much higher for nickel than for iron, it was found convenient to construct two separate systems for gas preparation. In both cases, the ratio of argon to the sum of the other two gases was at least 4, the proportion of hydrogen and water vapor being varied to produce H,O:H, ratios from 0.2 to 70. The primary purpose of the argon was to diminish the errors caused by thermal separation' in the gas phase. In addition, its presence lowered the saturation temperature required for a given H,O:H, ratio and minimized the difficulty of preventing condensation. Both systems were modifications of the one used by Dastur and Chipman.' For H,O:HI ratios greater than 2, welding-grade argon purified by passage over magnesium chips at 620°C was mixed with hydrogen produced in the electrolytic cell shown in Fig. 1. The design was based on a cell used by Bodenstein and Pohl," the important features of which area nickel wire cathode and sodium hydroxide solution as the electrolyte. The rate of hydrogen evolution was controlled by a calibrated ammeter and a rheostat in the circuit, the current efficiency being taken as 100 pct. Precise control of the argon flow rate at about 300 ml per min was achieved by means of a capillary flowmeter having a controlled pressure drop. The molar flow rate was measured volumetrically before each run, and a constant flowmeter setting was maintained thereafter. The A-H, mixture passed through a water saturator of the type previously described," the saturation temperature being maintained automatically with a fluctuation of k0.04"C. The tube between saturator and furnace was heated by a resistance winding. The system was of all Pyrex construction with the exception of the stainless steel tube containing magnesium chips. This was connected with the glass tubing at the upstream end by

Jan 1, 1957

By F. R. Jones

AT Tahawus, N. Y., National Lead Co. operates the MacIntyre development. Here the world's largest titanium mine produces 5200 long tons of ore per day and pours 8000 long tons of waste rock over its dumps. Concentrated ilmenite is sent by rail to National Lead Co. pigment plants, and a second product, magnetite, is sold to steel producers in raw form or is agglomerated and shipped as sinter. Several earlier attempts had been made to produce iron from the deposits, which have been known since 1826. These attempts failed, chiefly because of titanium impurity. In 1941 the present owners reestablished the operation for production of war-scarce ilmenite, and the impurity became the main product. The Ore: The MacIntyre ore zone is about 2400 ft long and 800 ft wide in horizontal measurements. Ore outcrops were found on the northwest side of Sanford Hill, 450 ft above Sanford Lake and 2500 ft southeast. The zone dips at about 45" toward the lake and plunges to the southwest. The ore minerals, ilmenite and magnetite, are unevenly distributed in bands roughly parallel to the long axis of the ore zone and are interspersed with bands and horses of waste. Hanging wall ores are fine grained and grade from rich ore to waste rock or gabbro. Footwall ores are coarse grained and are almost entirely ilmenite and magnetite. The foot-wall waste rock, anorthosite, is the common country rock. Several faults cut the ore zone. These faults have no great displacement but do contribute to the great physical variations in ore rock and surrounding waste. The Mine: The MacIntyre mine is an open pit operation, with benches at 35-ft intervals. The lowest bench is now 54 ft below lake level. Loading equipment consists of three electric-powered shovels (a P & H model 1400 with 4-yd dipper and two Bucyrus-Erie models 85-B with 2%-yd dippers) and one diesel-powered shovel (a Northwest model 80D with 2%-yd dipper). Ore and waste are transported to a 48x60-in. jaw crusher in ten 22-ton Euclid trucks with 300-hp diesel engines. Ordinarily the two Bucyrus-Erie 2 % -yd shovels load ore into a fleet of three or four trucks. This combination works two 8-hr shifts per day, moving 5200 long tons of ore to the crusher and removing a small portion of the waste rock. The P & H model 1400 shovel, with a fleet of four trucks, loads waste on three shifts per day. The mine operates on a 5-day week, with a small maintenance crew working Saturday. Oversize rock is broken by a dropball handled by an Osgood model 825 rubber-mounted crane.' Ore and waste are broken by drilling and blasting 9-in. diam vertical holes behind the benches. Bucyrus-Erie 42-T churn drills are used to drill the holes, which are extended 4 ft below the bench level on which the broken rock will fall. Drilling and Blasting History: In its early years the mine was equipped with Bucyrus-Erie 29-T churn drills, which drilled 6-in. holes. To keep up with production requirements the hole diameter was soon increased to 9 in., and by 1950 the three 42-T drills now in use had been acquired. Early blasting experiments with different kinds and grades of explosive led to adoption of 90 pct straight gelatin dynamite as standard. It was recognized that this explosive was expensive, and from the start of operations until 1950 extensive experiments were made using blasting agents of the ammonium nitrate family. Results were recorded as uniformly poor, with great build-up of oversize rock. The expense of these experiments, and the discouraging results, caused the abandonment of any expectation of breaking MacIntyre rock with anything but 90 pct straight gelatin dynamite. Further standardization led to 9-in. well drillhole spacings set at 16 ft in ore and 18 ft in waste, exceptions being permitted only for unusual conditions. The hole burdens were theoretically about 22 ft. Due to the extreme back-slope of bench faces, caused by blasting with heavy charges of dynamite, actual burdens were commonly well over 30 ft. Lack of precise control resulted in many holes having a burden as light as 15 ft. General practice was to stem 6 or 7 ft of hole with magnetite concentrate, the amount of stemming being left to the discretion of the pit foreman. Usually all holes in a row were fired instantaneously with Primacord detonating fuse. Millisecond delays were

Jan 1, 1957

Jan 1, 1957

By Ulf S. Landergren

Diffusion coefficients and marker movements have been determined in brass using welded couples. Three different concentration ranges were employed at 750°C, while a fourth concentration range was measured at 500°, 600°, 700°, and 800°C. Marker displacements toward and porosity development in the high zinc side of the couple were observed in all cases. The results were interpreted as favoring a vacancy diffusion mechanism. IN the large amount of diffusion literature which has accumulated during the past half century, very few experimental data have been presented on body-centered-cubic metallic phases. The impressive combination of experimental and theoretical studies which has given the vacancy mechanism a fairly secure position as the preferred mechanism for most face-centered-cubic metals has no counterpart for body-centered-cubic phases, although the theoretical picture seems to be in a better state than the experimental work. The attempts to select diffusion mechanisms by the theoretical calculation of the activation energy for the various conceivable unit diffusion processes and the energy of formation of the type of lattice defect required have been based on models of two kinds. The first kind utilizes potential functions fitted for certain properties of pure crystalline copper; the second kind is fitted for sodium. The latter is an example of an open metal in which the metallic ion is small compared with interatomic distance,&apos; while the former is characteristic of the larger class of metals in which the ions have diameters about as large as the interatomic distance. brass should resemble copper in this fundamental property. It should be evident that results on the mechanism of diffusion obtained for one of these classes need not necessarily apply to the other. Huntington and Seitz, using a model of the copper type, showed that the activation energies to be expected for interstitial migration or a two-atom direct interchange were much higher than that for vacancy diffusion. Zener pointed out that a four-atom ring rotation would involve an activation energy considerably lower than the two unlikely mechanisms although still higher than the vacancy mechanism in the face-centered-cubic structure. Furthermore, he argued, the four-atom rotation would be relatively easier in a body-centered-cubic lattice and might be competitive with the vacancy mechanism. Paneth showed that a body-centered-cubic crystal-like sodium could form interstitial defects of special type, called a crowdion, by crowding an extra atom into < 111 > directions where the defects would affect a line of about eight atoms. The defect was constrained to move along the defining line. Unlike the face-centered-cubic case, therefore, the theoretical calculations for the body-centered-cubic mechanism do not provide a very clear-cut answer, and the absence of adequate experimental studies is the more serious. This investigation was undertaken for the purpose of obtaining useful information on diffusion in body-centered-cubic phases. brass was chosen for several reasons: 1—the phase field is sufficiently wide at high temperatures to permit the use of diffusion couples with adequate concentration ranges for satisfactory chemical analysis, 2-—thermodynamic activity data are available for the calculation of mobilities from diffusion coefficients, 3—the phase is as close to the theoretical model of the copper -type on which the calculations have been done as any body-centered-cubic metallic phase is likely to be. Measurements of the movements (if found) of inert markers during the diffusion process would indicate that a vacancy or Or mechanism played a major role in diffusion in brass. If no marker movement should be found, a ring mechanism would be indicated but not assured. Experimental Procedure The alloys used in these experiments, listed in Table I with analyses, were supplied by the Naval Research Laboratory. They were from ingots of 3x3 in. cross-section, heated to 760°C, reduced under a

Jan 1, 1957

ANY suitable characterization of the Utah Copper enterprise (now the Utah Copper Division of Kennecott Copper Corporation) involves the use of superlatives. If comparative records were compiled, after the fashion of baseball, the big opencut mine at Bingham Canyon, Utah, undoubtedly would hold dozens of championships in the mining world. For example, a few can be set down as follows: (1) The mine is the biggest man-made hole (excavation) in the crust of the earth! At the end of 1955 the total quantity of material moved (ore and overburden) was 1,673,000,000 tons or approximately 800,000,000 cubic yards. This is about3% times the yardage of earth moved in the original digging of the Panama Canal. It exceeds by fifty per cent the quantity dug in the justly famous Hull-Rust Mahoning open-pit iron mine on the Mesabi Range in Minnesota. (2) It holds first place among the mines of the world as to aggregate tonnage of ore mined and milled (734,000,000 tons at the end of 1955). (3) It holds first place among the mines of the world as to the aggregate quantity of metal produced (13,047,000,000 Ib- 6,523,500 tons-of refined copper). This is more than the actual production of all the mines in the United States during the eight-year period 1948 to 1955 inclusive. (4) In 1943, Utah established these world records: Tons of ore milled in a 24-hr day.. ................. 108,000 Tons of ore and waste moved in a 24-hr day.. ....... 235,000 Tons of ore milled in one month. ................... 3,074,000 Tons of ore milled in a year. ....................... 35,375,000 Pounds of copper produced in a year……….. 639,0000,000

Jan 1, 1957

By H. W. Mead, C. E. Birchenall

The rates of growth of graphite nodules in cast irons are calculated for a model of a growing graphite sphere surrounded by a shell of austenite through which carbon and iron are diffusing. The carbon is supplied by a cementite-austenite mixture at the outer edge of the shell. The calculated rates from carbon diffusion agree fairly well with the measured values, but the rates based on iron self-diffusion are much too low. Because the iron must be removed for the process to continue, o plastic deformation mechanism is suggested. THERE has been an unfortunate tendency in the literature of growth and dissolution reactions to identify the slope of a plot of the logarithm of the growth or dissolution rate vs reciprocal of temperature with the activation energies determined by diffusion measurements in chemically similar systems. If the solubility limits at the growing or dissolving phase interfaces change appreciably with temperature, such procedures may lead to serious errors in specifying the mechanisms controlling the rates of these processes. A reaction involving the simultaneous growth of graphite from and dissolution of cementite in austenite will be discussed here to show that substantial oversimplifications have been made in earlier studies of this process. From a dilatometric study of the overall y-range graphitization process, Bunin and Danil&apos;chenko&apos; found an apparent activation energy of 90 kcal per g-atom. They concluded that, since this value was much nearer the approximately 68 kcal per g-atom observed for self-diffusion in pure iron than it was to 32 kcal per g-atom for diffusion of carbon in iron, the rate-controlling process must be the diffusion of iron away from the growth interface to provide space for graphite to grow. Bunin and Salli&apos; bolstered this agreement with the observation that graphite forms preferentially at surfaces, cracks, and pores where free volume is present initially. Ziegler, Meinhart, and DeaconQ ad found an apparent activation energy for graphitization of 98 kcal per g-atom. This value, like that of Bunin and Danil&apos;chenko, applies to nucleation and growth occurring simultaneously. It is not generally assumed that nucleation is entirely diffusion-controlled. Treatments such as prior cold-working and prequenching, which strongly affect the rate of graphitization, would be expected to have little effect on diffusion processes occurring at the graphitization temperature. In any case 90 kcal per g-atom is not particularly close to the 54 kcal or lower to be expected for diffusion of iron which is carbon-saturated.&apos; The presence of silicon in iron is said to reduce the activation energy for diffusion,&apos; so its presence in cast irons would be expected to have a similar effect. The growth rates of nearly spherical graphite nodules have been studied by Brown and Hawkes." The initial rate of growth before impingement of adjacent carbon-depleted areas was found to be parabolic, and rate constants were measured at several temperatures. Their apparent activation energy for the growth process only was roughly 45 kcal per mol. Burke and Owen&apos; made growth-rate measurements on several alloys, recording appreciable induction periods, initial nucleation rates, and average radial growth rates based on an assumed linear rate of radial growth. They found that increased silicon content increases the ovel-all reaction rate and the initial rate of nucleation, and decreases the induction period. Assuming 1) spherical nodules. 2) constant volume rate of nucleation, 3) austenite in equilibrium with cementite at positions where the cementite is not depleted, and 4) a constant diffusion distance during the growth of a nodule, they calculated an apparent overall activation energy of 68 kcal per mol, which was related to an activation energy for nucleation of 79 kcal per mol and activation energy

Jan 1, 1957

By J. Gordon Parr, D. H. Polonis

The formation and subsequent decomposition of metastable phases in Ti-Ni alloys containing up to 11 pet (atomic) Ni have been studied. The decomposition of a completely retained ß phase and of a completely transformed 8 phase in a 6 pet alloy has been followed by X-ray diffraction and metallographic methods and by hardness determinations made during the process. The possible mechanisms of the reactions are discussed. PREVIOUS investigations of the Ti-Ni system have usually been limited to phase diagram studies; but little attention has been given to metastable phases and tempering processes. These are important, however, since equilibrium conditions are rarely achieved—nor, perhaps, are they desired—in practice. Up to the present time the available transformation data for titanium alloys appear to be restricted to isothermal transformation curves for selected binary and ternary systems. No quantitative studies have been made of the mechanism by which equilibrium is approached. Several independent investigations have been carried out to determine the Ti-Ni phase diagram. Early work by Wallbaum&apos; and later by Long et al.&apos; produced tentative phase diagrams which were not representative of true binary conditions, since the alloys were contaminated with oxygen and nitrogen. The most recent diagram (Fig. 1) is due to Margolin et al.," and a slight modification of the a + ß/ß boundary (shown dotted) has been proposed by McQuillan.&apos; The structure of the phase Ti,Ni was shown by Duwez and Taylor" to be face-centered-cubic, with 96 atoms per structure cell. The formation of a martensitic ß phase (close-packed-hexagonal) in Ti-Ni alloys has generally been observed when specimens of low nickel content are rapidly cooled from the 0 (body-centered-cubic) range. Margolin et al. reported an increasing tendency for P to be retained in lump specimens as the nickel content increases. McQuillan&apos; has studied the effect on the microstructure of delay time in quenching, and has reported the formation of pro- eutectoid a precipitate in a quenched hypoeutectoid alloy. In a previous study of Ti-Fe alloys," experiments were made on powder specimens produced by filing alloy ingots. Techniques were devised for the preparation and heat treatment of alloys, and X-ray diffraction methods were used both for structure determinations and phase ratio estimations. A similar approach has been made in this study of Ti-Ni alloys. Experimental Methods Ten alloys ranging from 0.25 pet to 18 pet Ni* * All compositions are in atomic percentages unless otherwise stated. were prepared from iodide titanium bar stock (hardness Rf 72) and Johnson-Matthey spectrographic standard nickel by levitation melting.&apos; As a check

Jan 1, 1957

By Robert Corcoran, George Wiener

A study of the orientations and microstructure of 3 pct Si Fe alloys after deformation and recrystallization has been made. The components found after deformation agreed with recently published work on single crystals, being primarily (001) [110], (111) [110], and (111) {112}. A pronounced effect of temperature of recrystalliza-tion was found on microstructure and orientation. Low temperature recrystallization was interpreted in terms of low angle boundaries which resulted in the retention of a large amount of the deformation texture. High temperature recrystallization was interpreted in terms of high angle boundaries which gave rise to new components. No simple angular relation between the deformation and high temperature recrystalliza-tion textures could be detected. DEFORMATION and recrystallization behavior of 3 pct Si-Fe has been the subject of scientific investigation for many years. The fact that it is a single phase body-centered-cubic alloy from room temperature to the melting point permits study over a wide range of temperature without the complications of phase transformations. There is an important commercial interest in this material as well, since it is widely used in the electrical industry. In the present work the deformation and recrystallization behavior of poly crystal line silicon iron has been studied with the primary purpose of evaluating the effect of a second phase impurity on both processes as well as the effect of temperature on the recrystallization characteristics. With regard to deformation, the emphasis has been placed on a study of the crys-

Jan 1, 1957