Search Documents

By I. Fatt

Networks of resistors are used as analog computers to obtain relative permeability and resistivity index curves for networks of tubes. These curves have all of the characteristics of those obtained on porous media and, therefore demonstrate the validity of the network of tubes model. INTRODUCTION In paper I' of this series the network model was shown to give information on the structure of porous media that could not be obtained from the bundle of tubes model. The agreement between the capillary pressure characteristics of a network of tubes and those of typical porous media does not prove the validity of the network made. The bundle of tubes model, although it gives less information, also shows this agreement. In this paper the flow properties of a network of tubes are shown to be in agreement with flow properties of porous media. The flow properties of the bundle of tubes model are not in adequate agreement with those of porous media. The dynamic properties of porous media, such as fluid permeability and electrical conductivity, have been found experimentally to be more sensitive functions of structure and pore size distribution than are the static properties such as porosity and capillary pressure characteristics. The network model can, therefore, be best tested by comparing the dynamic properties of a network of tubes with the observed properties of porous media. All static and dynamic properties of a completely valid model must agree with the observed properties. The most commonly measured sensitive dynamic properties are the relative fluid permeability and the relative electrical resistivity. Experimental measurements of these dynamic properties on sandstone, sintered glass, sintered alumina, and soil are reported in the petroleum and soil science literature. These properties were chosen, therefore, for the test of the network model. In the network model, relative permeability is the permeability of the network when some of the tubes are not conducting fluid, relative to the permeability when all tubes are conducting fluid. Similarly, the relative resistivity is the electrical resistivity of the network of tubes when some of the tubes are filled with a nonconductor. relative to the resistivity when all tubes are filled with the electrical conducting fluid. Single Size Tube Network The simplest porous medium is one in which all pores are of the same size. Such media can be approached by packing beds or columns of uniform size particles of sand, glass, or metal. The model of such medium in this study is a network of single size tubes. The network form, the ß factor, is usually not known for real porous media. If the validity of the network model can be established, then the study of the flow properties

Jan 1, 1957

By K. G. Wikle, J. G. Klein, W. W. Beaver

Consolidation of hydride process, electrolytic, calcium reduced, and comminuted thorium powder, as well as saw chips and lathe turnings, by vacuum hot pressing and by cold pressing-vacuum sintering was studied. The mechanical properties of the consolidated material in the extruded form are compared with those of wrought castings. AT present there little little industrial use for thorium metal, although it has some important though small scale applications in electronic equipment. Despite its high inelting point—about 1750°C —a low modulus of elasticity, 11.4xl0 si at 20°C;' relatively low mechanical properties coupled with a high density, 11.7 g per cu cm; and an unusually high chemical activity with normal atmospheres limit any structural applications. The metal is utilized as an alloying element principally in magnesium. Pure thorium finds utility as electrodes in gaseous discharge lamps such as the high intensity mercury lamp' because its low work function and high electron emissivity provide lower starting potentials and more uniform operating characteristics than other available materials. The metal is also found in photoelectric tubes used for the measurement of the ultraviolet spectrum." Thorium metal has been used in germicidal lamps of the cold cathode type as sputtered coatings on nickel in order to provide a low work function surface and a low starting voltage. Other applications have involved the radioactive properties of thorium for the production of ionized particles." The potential value of thorium is much greater than its present use pattern because of possible utility in the field of nuclear power. Th may be converted through nuclear reaction to a fissionable element U which should be capable of acting similarly to U in the g'eneration of atomic power. Thorium has been reported to be about three times as plentiful as uranium in the earth's crust, placing it in the order of abundance of lead and molybdenum." Thus, it is of interest in augmenting the potential supply of fissionable material for nuclear power. Because of its high melting point, thorium is usually produced as a powder through the calcium reduction of its oxide or thermal reduction of halides by sodium, magnesium, and calcium. It may also be produced in flake form by electrolysis of fused alkali or alkaline earth chloricles and fluorides. Therefore, powder metallurgy assumes importance in the fab- rication of thorium metal shapes. Furthermore, it is rather difficult to obtain pure thorium by melting, as the molten metal reacts readily with graphite as well as oxide, carbide, and nitride refractories. These contaminate the melt with oxides, carbides, and metallic impurities." The current investigation was undertaken to examine the fabrication of thorium by powder metallurgy methods which have been used for the commercial production of beryllium and other metals.' A sparcity of data concerning the comparative cold and hot compaction of thorium powders of different derivation existed. Therefore, all commercially available types were examined along with other experimentally produced thorium powders in order to round out the comparison of consolidated thorium powders with melted reguline metal. Review of the Literature By heating a mixture of ThC1, with potassium, Berzelius made the first thorium metal as an impure powder in 1828. Improvements in the basic process, increasing thorium assay to 99 pct, were made by several investigators including Arsem," Lely and Hamberger10 and Von Bolton." Calcium reduction of Tho, to make powders was investigated by Berger," Huppertz,'" Kroll," and Kuzel and Wedekind.'" A thorium powder produced by this method using a CaC1, fluxing agent assayed 99.7 pct, as reported by Marden and Rentschler.'" Compacted and sintered, this product was found to be ductile, and could be fabricated into wire and sheet. Improvements of the calcium reduction process were made later" wherein CaCl, was eliminated from the reaction, producing metal assaying 99.8 pct Th. Further work by Lilliendah118 howed that a coarser metal could be obtained by the substitution of ThC1, or ThOC1, for oxide with consequent advantage of stability to atmospheric reaction. Reports on the technology of thorium developed in Germany during World War II have been made by Espe."' Thorium powder of 99.5 pct Th was obtained by reduction of the oxide by calcium. Screening to —200 mesh, compacting with about 20 tsi, and sintering in vacuo at 1320" to 1360°C for 3 hr resulted in a porous sinter cake. The sinter cake was sufficiently ductile to be worked into bar, wire, and sheet which could be employed as electrode materials.

Jan 1, 1957

By L. F. Stutzman, George Thodos

The friction factor plot presented by Cornell and Katz4 and developed for the flow of fluids through consolidated formations has been directly adapted for handling fluid flow problems involvitrg both linear and radial flow. In this adaptation the friction factor plot is used directly for the solution of problems and thereby eliminates the use of conventional equations which are specific to laminar (Darcy) or turbutent flow. This upproach overcomes the disadvantages inherent in the use of these conventional equations. It eliminates the necessity of checking the type of flow occurring in order to identify the specific equation which must be used. In radial flow problems, because of the increasing mass velocity of the fluids as they approach the wellbore. the type of flow may no longer remain laminar. Consequently, it is necessary to use more than one equation in a problem and to identify the range over which each equation should be applied. Finally, in practice it has been found that much of the flow of gases through consolidated media occurs in a range that is neither laminar or turbulent. For this transitional region, no convenient equations are available. The method and presented friction factor plot are appficahle to both liquids and gases. INTRODUCTION The flow of fluids through unconsolidated media in packed beds has been treated extensively by a number of investigatorsl,2,3,5,7,8 Most of these studies present friction factors as a function of modified Reynolds number similar to those developed for conventional fluid flow through pipes. These friction factor plots are presented for linear flow; however, Elenbaas and Katz have extended these concepts to apply to radial flow. All of these studies on unconsolidated materials require a knowledge of packing properties such as sphericity. porosity, and particle diameter. Sphericity and particle diameter cannot be defined at the present time for consolidated formations such as those commonly found in gas or oil reservoirs. As a result many investigators have not utilized friction factors and Reynolds number in the study of fluid flow through consolidated media. However, Cornell and Katz4 present a plot (Fig. 1) for the flow of fluids through consolidated porous media, in which the friction factor defined as: The turbulence coefficient, P, is related to the formation permeability, K, as presented in Fig. 2. Three different types of flow may exist in the flow ot

Jan 1, 1957

By Grant S. Diamond

THE BIBLIOGRAPHY on the use of static electricity in mineral beneficiation consists largely of patents. Some references are found in mineral textbooks, but very little data on flow-sheets of commercial installations are known to the writer. As a matter of fact there have been relatively few successful commercial applications of importance. Johnson prepared and published a Table showing the polarity and static field intensity requirements of many minerals. There have been reports of successful beneficiation of rutile, zir-con, coal, potassium chloride, and phosphate rock. Otherwise, the field of success has been very limited. This may be due to three reasons: first, the mining industry has been averse to dry processes, be-cause of dust nuisances in dry crushing; second, the electrostatic processes used in the past apparently developed no substantial economic advantages; and third, because flotation or other . methods have proven successful on many minerals, the industry has not felt the need for a radically different process. In the feldspar industry there was ?an attempt at electrostatic beneficiation about twenty years ago which was based on the use of fluoride fuming of the pegmatite head feed, in order to make the mineral reactive in a static field. This process was originally said to be successful, but was discontinued because of corrosion damage to machinery. Another effort by use of a chemical additive such as an or-ganic hydroxyl compound has also been attempted. Neither of these processes is known to be in use today.

Jan 1, 1957

By R. A. Hatch

This report summarizes the results of nearly 8 years research on and production of synthetic mica at the Electrotechnical Experiment Station of the Federal Bureau of Mines, Norris, Tenn. This program was undertaken at the request of the United States Department of the Navy and was financed mostly by the Army Signal Corps and the Navy Bureau of Ships through a contract with the Office of Naval Research, The original objectives included fundamental studies of fluor-phlogupite and other fluorine-micas and production of synthetic mica sheets on a pilot-plant scale. The first 3 years of this project were devoted mainly to a search for practical solutions of the many problems involved in designing and constructing a pilot plant for crystallizing fluor-phlogopite mica. The first and most urgent need was a suitable container for the corrosive mica melt. After extensive study, it was concluded that platinum, graphite, high-silica fire clay, and silicon carbide were the most promising refractories for crucibles; but none was perfect. Silicon car¬bide seemed to have the better combination of qualities, combining good corrosion resistance with oxidation resistance.

Jan 1, 1957

The Tuesday morning session of the Rocky Mountain Coal Mining Institute was opened at 9:00 a.m. by Bob von Storch, in the absence of the President. Mr. von Storch appointed the following new members to the Resolution Committee in the absence of three of the members: Albert Keenan, E. S. O'Connor and Howard Crandell. This committee was asked to be ready to report at the Wednesday morning session. Mr. von Storch then introduced Lyman Fearn, State Mine Inspector for the State of Wyoming, who presided over the morning session. Mr. Fearn introduced the first speaker for the morning, Louis A. Engstrom, Engineer at Kemmerer Coal Company, Kemmerer, Wyoming, who delivered a talk illustrated with slides in the absence of Mike Zakotnik, Jr., who was unable to attend. (Please refer to the index for printed text of this paper.) The next paper, "New Horizons -Coal for the Steam Plants of the West," was delivered by Don Newberry, superintendent of the Castle Gate Mine of the Independent Coal and Coke Company, Castle Gate, Utah, in the absence of W. J. O'Connor. (Please refer to the index for printed text of this paper.) Bob von Storch then introduced Edward G. Fox, President of Bituminous Coal Operators' Association, Washington, D. C., who delivered a paper on "A New Era in Labor Relations."

Jan 1, 1957

The large increase in secondary industries in this country, during the war and post war periods, has caused a shortage of capacity for the production of merchant bar.To overcome this shortage, an expansion of rolling mill facilities has been undertaken by the Broken Hill Pty. Co. Ltd. A small, but modern, merchant mill has been erected at Kwinana in Western Australia and a strip and skelp mill is under construction at Newcastle. The latter mill will roll strip and skelp at present being rolled by the Newcastle 10 in. Merchant Mill, enahling this mill to concentrate on merchant bar production.The Kwinana mill was installed to supply the Western Australian market. This state has a small population (approximately 658,000) and is not at present highly industrialised. It was necessary, therefore, to design a mill which would be capable of producing a wide diversity of sections and could be expanded as the demand increased. To begin with capital expenditure had to be kept within reasonable bounds. The design work for this mill, with the exception of a few specialised items of equipment, was carried out at Newcastle.All design work for the Newcastle mill was carried out by the lVIorgan Construction Co. of America. Although initially intended for rolling flat. products, the designers were asked to make the mill as flexible as possible, so that should the market for flat products decrease, this mill with additional equipment could undertake the rolling of medium sized sections.

Jan 1, 1957

By F. N. Bender

Percolation leaching of wad-type manganese ores was investigated, using a novel system of alternate upward passage of sulfur dioxide gas through moistened ore and downward percolation of wash solutions to extract solubilized manganese. Bench and large-scale tests designed to simulate vat and heap leaching were made on four wad ores from Arizona and Nevada and on a pailomelane ore from Arizona. Three of the wad ores required prebaking at 500° to 600° C. to produce a permeable agglomerate that would not slake during percolation washing. The hard-type ore and one of the wad ores that contained a large amount of granular gangue did not require prior roasting. The deportment of the different ores toward leaching and percolation was studied with particular reference to the influence of the sulfur dioxide - oxygen ratio and the effect of gas dilution on the rate of manganese dissolution, dithionate formation, and acid production. Crushed charges of the ores, as coarse as 1 inch and as fine as 1/4 inch, were treated for periods of 5 to 11 days. Percolation of the gas and leach solutions through the charges was achieved without difficulty. The manganese extractions varied between 78 and 97 percent and depended upon the size and type of ore leached. The average quantity of sulfur dioxide required in the larger scale tests was about 2.6 pounds per pound of manganese recovered. The dithionate formation varied from 0.35 to 0.9 pound per pound of manganese extracted depending upon the strength of leaching gas.

Jan 1, 1957

By H. Hansen, A. U. Seybolt, P. Yurcisin, B. W. Roberts

The Bi-Mn phase diagram in the region near BiMn was investigated, using principally thermal analysis and changes in magnetization with temperature. Of chief interest are the findings related to the magnetic transformation in Bi-Mn. THE Bi-Mn system is of both theoretical and practical interest because of the occurrence of the compound BiMn which exhibits unusual ferromagnetic properties. Because the Bi-Mn phase diagram reviewed by Hansen' (see Fig. 1) in 1936 is based on work done by BekierY in 1914 and by Siebe" in 1919, which left considerable doubt about the nature of the diagram. it appeared desirable as an aid in understanding the alloying characteristics and magnetic behavior to examine the pertinent regions of the phase diagram. The most interesting reaction is the peritectic at 445°C which forms BiMn by the reaction: Liquid + Mn(sulfield) ? BiMn(sol field) There is also a eutectic at 262° C between pure bismuth and BiMn. Hansen draws in BiMn dotted, since in 1936 evidence for its existence was uncertain. Experimental Materials—Preparation of Alloys Electrolytic manganese of about 99.97 pet purity and bismuth of 99.99 + pet purity were used as starting materials.

Jan 1, 1957

Jan 1, 1957

By W. R. Hibbard

Pole figures, torque curves, and coercive force have been determined for the following rolled and annealed permanent magnet alloys: Cunife, Cunico, Silmanal, Vicalloy I, Vicalloy II, and Heusler's Alloy. IN the general category of precipitation-type permanent magnet alloys there is a group of ductile alloys, including Cunife, Cunico, Silmanal, Heusler's Alloy and Vicalloy, which can be extensively rolled and annealed to develop a preferred orientation in the crystals of the matrix material. The rolling and annealing textures of Cunifel and Vicalloy' have been previously investigated qualitatively, but no pole figures are available in the literature. In addition, the role of precipitation in these permanent magnet alloys is still somewhat controversial. It

Jan 1, 1957

By R. W. Cahn, C. D. Graham

Two predictions of the oriented growth theory of recrystallization textures have been tested by measuring the orientation dependence of the rate of growth of a single grain into a strained single crystal of aluminum, and determining the orientations of artificially and spontaneously nucleated grains growing preferentially into strained aluminum single crystals. Growth rates are found to be insensitive to orientation, except that new grains with orientations similar to the matrix or to a twin of the matrix have very low mobilities. Similarly, new grains growing preferentially into a strained crystal have random orientations, except that orientations near that of the matrix or its twins are avoided. The predictions of oriented growth theory are thus not confirmed. BASICALLY, the oriented growth theory of re-crystallization textures1 rests on the assumption that the rate of growth of a recrystallizing grain depends strongly on the orientation of the growing grain relative to the strained matrix into which it grows. In particular, the theory holds that in face-centered-cubic metals the orientation which corresponds to maximum growth rate is one in which the growing grain and the matrix are related by a rotation about a common <111> direction. The amount of rotation, as derived from several kinds of experiments,2-1 has been assigned various values, generally in the range between 20" and 40". (A <111> rotation of 60" is a twin relationship.) The conclusion that boundary migration rates depend strongly on orientation is based almost entirely on indirect evidence; there have been very few direct measurements of boundary migration rates as a function of orientation.* " The present investigation was undertaken to provide such measurements, to help make possible a decision between the oriented growth and oriented nilcleation theories of recrystal-lization textures. The basic experimental program consisted of measuring the rate of growth of a single recrystal-lizing grain consuming a strained single crystal, with the orientations of both grains preselected so that the effect of orientation on growth rate could be determined. A prerequisite for such an experiment is a strained single crystal which will support the growth of a new grain but which will not spontaneously nucleate new grains on heating. That is, the crystal must support the growth of a grain nucleated artificially, but contain no recrystalliza-tion nuclei which will become active at the testing temperature. Beck was apparently the first to note that such a condition could exist," and to make use of the condition for am experiment of the type described here.&apos; The present work was actually suggested, however, by a report of Tiedema". " that an aluminum single crystal strip, oriented with a (111) plane in the plane of the strip and a < 112> direction parallel to the tensile axis, would not recrystallize after 20 pet extension even when heated almost to the melting point, provided that the strip was heavily etched before being heated. This result could not be duplicated in the present work. In fact, it was found that any crystal which deformed in multiple slip (<100>, <112> and <111> orientations) underwent spontaneous nucleation after 15 pet extension, even if etched. However, crystals which deformed in single slip, and which did not develop heavy deformation bands, could be extended 15 pet without showing spontaneous nucleation at temperatures up to 600°C. Crystals oriented within about 10o of <110> which developed heavy deformation bands could be extended 10 pet without showing spontaneous nucleation. In all cases a heavy etch was required to prevent nucleation. Etching was necessary because of the presence of an oxide layer on the crystal surface at the time of straining, which leads to preferential nucleation at the surface.&apos;&apos; Grain Growth Rates Experimental Procedure and Results—Aluminum strips of 99.6 pet purity (principal impurities 0.19 pet Fe and 0.12 pet Si), 1 mm by 1 cm in cross section, were grown into single crystals of controlled orientation by the strain-anneal method of Fuji-wara.&apos;"&apos; " A sharp temperature gradient was maintained in the strips during growth by lowering them into a salt bath controlled at 650°C. Crystal orientations were determined by the etch-pit method of Barrett and Levenson" to an accuracy of ±2O. The crystals were extended by 10 or 15 pet in a simple hand operated tensile machine. Crystal orientations were rechecked after extension, and were found to be in agreement with the orientations predicted by the formula of Schmid and Boas." After extension, the grip ends of the single crystal specimen were cut off with a jeweller&apos;s saw, and the crystal heavily etched (at least 20 pet wt loss) in hot 10 pet Na or KOH solution. A region of severe local deformation was then introduced at one corner of the strip, usually by cutting off the corner with shears. Heating this end of the strip caused a large number of new grains to nucleate at the sheared edge. One of these grains grew to occupy the full width of the strip. The appearance of the strip at

Jan 1, 1957

In common with general experience in the iron-making industry overseas, Australia has in recent years suffered a deterioration in the physical quality of her iron ores in their suitability as a direct blast furnace feed. The increasing amounts of fines and the more friable nature of lump ore, especially in the ore from the Cockatoo Island deposits in Yampi Sound, Western Australia, have focused attention on problems of ore preparation and agglomeration, particularly sintering.Although very small pilot scale Dwight-Lloyd type sinter machines were operated at the steel-making centres at Newcastle and Port Kembla during World War II, no sizeable capacity was installed, so that ore was charged to the blast furnaces almost entirely unscreened, and the resultant flue dust was stockpiled.Towards the close of the war, the pilot plant at Newcastle was replaced by a small machine, adjacent to the flue dust stockpile, with a rated capacity of some 20 tons per hour. After approximately five months of part-time operation, this plant was closed down in January, 1945. Production was not resumed until December, 1950, when, due to a temporary ore shortage, it was decided to supplement available ore with sinter produced from the large flue dust stocks of about 300,000 tons. In spite of mechanical and process difficulties, inherent to the design of the plant, operation was continued on a two-shift basis, with several shutdowns for extensive overhaul and plant alterations, until September, 1954, when production was put on a three-shift basis. Addition of Yampi ore fines to the sinter machine burden was not commenced...

Jan 1, 1957

COUNCIL OF EDUCATION OF AIME (Formerly Mineral Industry Education Division) Established as a Division January 15, 1932 Established as a Council February 26, 1957 John C Calhoun, Jr, Chairman 0 Cutler Shepard, Vice-Chairman Thomas A Read, Secretary-Treasurer Dept of Mining & Metallurgical Engrg University of Illinois Urbana, Illinois COUNCIL OF ECONOMICS OF AIME (Formerly Mineral Economics Division) Established as a Division December 15, 1948 Established as a Council February 26, 1957 Louis C Raymond, Chairman Lorin A Cranson, Vice-Chairman Henry T Mudd, Vice-Chairman Adam K Stricker, Jr, Vice-Chairman Paul F Yopes, Secretary-Treasurer U S Bureau of Mines Albany, Oregon

Jan 1, 1957

President and Director GROVER J HOLT, &apos;59, Ishpeming, Michigan Past President and Director CARL E REISTLE, JR, &apos;58, Houston, Texas President-elect and Director AUGUSTUS B KINZEL &apos;60, New York City Vice-Presidents and Directors W A DEAN, &apos;58, Cleveland Ohio W W MEIN, JR, &apos;58, San Francisco, Calif L E ELKINS, &apos;59, Tulsa, Okla J L GILLSON,&apos;59, Wilmington, Delaware E C BABSON, &apos;60, Calgary, Alberta, Canada R V PIERCE, &apos;60, Salt Lake City, Utah

Jan 1, 1957

By Austin E. Dwight

IT has been shown by Oelsen and Wever&apos; that the effect of a solute element on the allotropic transformation in iron is dependent upon the quantity

Jan 1, 1957

By R. H. Frazier, C. H. Lorig, F. W. Boulger

THERE are both advantages and disadvantages in using semikilled steels in place of killed steels. One advantage of semikilled steels is they provide a higher ingot-to-product yield. This is especially important to shipbuilders in the time of national emergency. By using semikilled steel for hull plates, a greater number of ships can be built from the same ingot tonnage. Consequently, if semikilled steel plates are adequate for the service, the advantage of the higher product yield is of considerable importance. The performance of hull plates is closely associated with the ductile-to-brittle transition temperature, and this, in turn, is strongly dependent on the composition of the steel. A low transition temperature is desirable because it indicates that the steel is less likely to fail at low ambient temperatures. Killed steels are known to have lower transition temperatures than semikilled steels. It is believed that the better qualities of killed steels in this respect are due mainly to the low oxygen contents of the steel. The principal deoxidizers, aluminum, silicon, and manganese, lower the oxygen content. Fundamental studies1-0 have shown that the oxygen content remaining after the addition of one of these three elements is influenced by the residual amounts of the other two present. In the current study, therefore, various amounts of silicon and aluminum were added to steels containing different manganese contents for the purpose of studying the influence of silicon and aluminum on the notched-bar properties of hot-rolled steels. Eleven types of steels were studied. The temperature at which the plates were finish-rolled was care- fully controlled at 1850°F. All plates were rolled to ¾-in. thickness, and tested in the as-rolled condition. The total number of steels prepared in the laboratory for this study was 95. The charge consisting of ingot iron and ferrosilicon equivalent to 0.10 pct Si was melted in a 200-lb induction furnace under an atmosphere of argon to insure low, uniform nitrogen contents. After the charge was melted and the desired temperature was obtained, the melt was partly deoxidized with either silicomanganese or aluminum. Aluminum was used for this purpose in only those steels with very low silicon contents, where the finished steel was to contain some aluminum. This initial deoxidizing addition was made to obtain consistent recoveries of subsequent additions of ferro-manganese, ferrosilicon, and aluminum. Carbon, in the form of graphite, was added, either just prior to tap or to the final aluminum addition. The entire heat of 200 lb was poured directly into a 6x6-in. big-end-up mold. The ingots of semikilled steel were capped with a steel plate. The killed steels, on the other hand, were poured with a hot-top containing 14 pct of the total volume of the ingot. The ingots were processed by heating to 2250°F, followed by forging to slabs 1¾ in. thick and 6 in. wide. After reheating to 2250°F, the slabs were rolled to 0.9-in. gage, using reductions of approximately 1/6 in. per pass. The 0.9-in. thick plates were immediately recharged in a furnace held at 1850°F. After 30 min in the furnace at 1850°F, the plates were rolled to ¾ in. in one pass. Following the final pass, the plates were stacked on edge on a brick floor, with a brick separating one from another, where they were allowed to cool in air. Drillings for chemical analysis were taken from the plates at locations corresponding to the top and bottom of each ingot. Carbon, manganese, silicon, phosphorus, sulfur, and nitrogen contents of each sample were determined. The analysis of each steel was carefully controlled so that the contents of

Jan 1, 1957

By Howard Martens, Pol Duwez

XPERIMENTS were performed on a Cr-Fc alloy Econtaining 44.7 pet Cr in order to determine the heat evolved during the transformation of the a solid solution into the s phase, and the change in volume accompanying the transformation. Since previous measurements on the rate of formation of a from s indicated that the reaction was quite fast as soon as the equilibrium temperature of 820°C was exceeded by some 50°, standard thermal analysis experiments were performed on heating specimens of s at the rate of approximately 40°C per sec. A definite thermal arrest was observed at 870"C, Fig. 1. This result indicates that the reverse seaction of into a is exothermic. From the heating curve of Fig. 1, taking 15°C per sec as the heating rate in the neighborhood of the transformation, 2.4 sec as the time for transformation, and assuming that the specific heat of the alloy at 850°C is an average between iron and chromium, namely 9.5 cal per mol per "C, the latent heat of transformation is approximately 342 cal per mol. The order of magnitude of this latent heat was also obtained by comparing the heating curve of Fig. 1 with a similar curve obtained with pure iron under identical experimental conditions. It was found that the length of the thermal arrest for s was about 1.8 times as long as that for iron. Since the latent heat of the a to 7 iron transformation is 203 cal per mol1, 2 the latent heat of it to a would be 365 cal per mol, which is in relatively good agreement with the value determined from the heating curve. For the determination of volume change, thermal expansion curves were recorded using a specimen containing 44.7 pet Cr and completely transformed to cr by previous treatment. The curves were recorded at a rate of heating of about 4°C per min and at approximately 840°C a sharr, increase in length of about 0.08 pet took place. Fig. 2. It is therefore established that the specific volume of a near the transformation temperature is about 0.24 pet smaller than that of a, and consequently, when the s phase forms in an a matrix, it would tend to shrink away from the matrix. Since the s phase is known to be extremely brittle, these results offer an explanation for the microscopic cracks often observed in the a phase under the microscope. The results of this study are in qualitative agreement with previously published data on stainless steel 19-9DLa and on a Cr-Fe alloy containing 45 pet Cr.&apos; The increase in density due to the transformation from n to s given in ref. 4 is 0.90 pet. These measurements, however, were made at room temperature. whereas the presently reported 0.24 pet is the change at the temperature at which the transformation takes place during heating. In the graph of Fig. 2, the percentage change in length that would be observed at room temperature is given by the length X, which is about 0.27 pet. This would correspond to 0.81 pet in volume change. Acknowledgment This work was done at the Jet Propulsion Laboratory, California Institute of Technology, under Contract No. DA-04-495-ORD-18 with the Army Ordnance Corps, Washington, D. C. The authors wish to thank this agency for permission to publish the results of this investigation. References I H. Klinkhardt: Measurements of True Specific Heats at High Temperatures. Annalen der Physik (1927) 84, pp. 167-200. - H. Esser and W. Runghardt: Influence of the Method, of Dctcrmination on the Measured Heat Content of Iron. Archtvo ffur Dct Eisenhiittenwesen 11934) 8, pp. 37-38. J. J. Gilman, P. K. Koh, and 0. Zmeskal. Delta Ferrite Formation and its influence on the Formation of Sigma in a Wrought Heat Resisting Steel. Trans. ASM 1 1949) 11, pp. 1371-1388. 1 J. M. Thomas: Discussion of ref. 3. Trans. ASM (1949) 41, pp. 3 390-1392.

Jan 1, 1957

By A. T. Corey, C. H. Rathjens

INTRODUCTION Although the oil industry has been aware of the directional variability of permeability in porous rock, the directional variability of relative permeability has been largely ignored. Yet it is apparent that such an effect must be present in a system in which the distribution of oil and gas within the porous matrix is controlled by capillary forces. It is easy to visualize a rock composed of layers of fine and coarse material such that gas flow across the bedding planes would take place only after the average oil saturation had been reduced to a very low value. The fine layers, because of their greater capillarity, would remain saturated and act as barriers to the flow of gas after the coarse layers had been desaturated. Flow of gas parallel to the bedding planes would obviously take place at a much greater liquid saturation. Without more complete information concerning the geology of a reservoir than is generally available, it is not possible to predict exactly how such phenomena would affect the over-all performance of an oil field. It is possible, however, to predict qualitatively the effect of stratification on relative permeability measurements made on laboratory cores. In this investigation the effect of stratification was studied analytically by assuming that two porous materials with different capillary pressure-desaturation curves (but identical relative permeability curves) were in contact and in capillary equilibrium. As a qualitative check on the analytical results, cores having various degrees of visible stratification were used for relative permeability measurements made with fluids flowing both parallel and perpendicular to the bedding planes. A quantitative check was considered impractical because of the difficulty of devising models in which two materials of predetermined properties could be joined without the plane of contact becoming a discontinuity. THEORETICAL CONSIDERATIONS AND ASSUMPTIONS The assumption of capillary equilibrium in an oil-gas system implies that the difference in pressure between oil and gas is everywhere the same. This means that the curvature of the interfaces must be everywhere the same in order to satisfy the equation where PC is the pressure difference between phases, y the interfacial tension and r, and r2 are the major and minor radii of curvature. Depending on the pore size distribution of coarse and fine layers, the volumetric percentages of oil and gas in these layers will differ when equilibrium exists. The exact relationship can only be determined by obtaining the complete capillary pressure-desaturation curves for each of the porous materials in contact. It has been pointed out elsewhere&apos; that the capillary pressure-desaturation curves of sedimentary porous materials can often be approximated by the relation where C is a constant and Soe is the effective saturation to oil based on a percentage of the pore volume effective to flow. In the same paper it was indicated that, as a first approximation, the values of oil relative permeability are given by and the values of gas relative permeability by For this analysis Eqs. 2, 3, and 4 were assumed to apply to each of two components of a hypothetical porous rock in capillary equilibrium. It was also assumed that each of the components had a residual wetting phase saturation of 20 per cent so that 80 per cent of the total pore volume was effective to flow. The permeability of the coarse stratum was taken as 100, and its displacement pressure was such that C in Eq. 2 had the numerical value of 1. The corresponding values for the fine stratum were 10 for the permeability and 10 for C. Units are not specified because they do not enter into the final results. The choice of the permeabilities and displacement pressure ratios was made to expedite the calculations. Any reasonable rock properties could have been chosen without changing the results qualitatively. Several arrangements of the two components were studied. Table 1 summarizes the resultant permeabilities obtained for four types of arrangement. RELATIVE PERMEABILITY CALCULATIONS The first step in the computation of relative permeability for the composite cores was the plotting of the capillary pressure-desaturation curves and the relative permeability curves for the individual components according to Eqs. 2, 3, and 4. At arbitrary

Jan 1, 1957

By C. M. Schwartz, J. R. Bridge, D. A. Vaughan

THERMAL expansion coefficients of a uranium were originally reported&apos; on the basis of X-ray diffraction measurement of lattice constants at 25°, 300°, and 650°C. These data have been reproduced by Katz and Rabinowitch.&apos; CuK radiation had been used in this work, with consequent crowding of the patterns. Considerable overlap of the back-reflection lines was observed as the temperature was raised. Subsequent reexamination of the data led to the conclusion that errors had resulted from failure to obtain unequivocal indexing of the high angle reflections at elevated temperatures. The measurements have been repeated, using FeK radiation, which provided sufficient dispersion to assure proper indexing of the reflections, at each temperature level. The unit cell dimensions were re-determined at ten temperatures, from 25" to 650°C. Schuch and Laquer easured the macroscopic contraction from room temperature down to —253°C, and reported a negative value from —210" to —253°C; they suggested the possibility of the occurrence of a phase change. In the present work, the lattice constants of uranium have been measured down to —253°C, to test this hypothesis. Filings were prepared from a single piece of pure uranium bar stock. They were carefully cleaned with a magnet and pickled in nitric acid to remove traces of iron from the file. They were then annealed at 600°C in a sealed evacuated silica tube. The annealed filings were pickled in strong nitric acid to remove any oxide layer, washed in water and alcohol, quickly dried, and sealed in evacuated thin-walled silica capillary tubes. If properly sealed, the sample could be heated to the a-ß transforination temperature without significant buildup of the diffraction pattern of oxide. The high temperature X-ray diffraction camera was modified from the design of Hume-Rothery and Reynolds.&apos; The thermocouple used to record the specimen temperature was calibrated from lattice-constant measurements of a standard silver specimen, using the Hume-Rothery and Reynolds values for silver over the temperature range from 25" to 700°C. Temperatures were reproducible to 210°C. Temperatures to —210°C were attained by passing precooled gas over the sample. The gas from the cooling train was directed over the sample capillary tube and thermocouple by means of a chimney of 1-mil polystyrene. The 36-gage Cu-constantan thermocouple had been calibrated by

Jan 1, 1957