Search Documents

By M. M. Fine

This report presents the results of laboratory mineral-dressing investigations by the Bureau of Mines of 14 individual or composite character samples from deposits in the Batesville manganese district. It will be noted that some concentrates have met or approached analytical specifications for metallurgical manganese ore although great variations in both physical and chemical composition from once deposit to another make each a new problem. In most cases it is evident that a substantial loss of manganese has occurred in the various slime and tailing products. An important aspect of this work is the research being conducted on manganese-bearing limestones. Recent reconnaissance indicates that this resource constitutes one of the major domestic reserves of manganese. Laboratory study has shown that ferrograde concentrates can be recovered from samples of manganese-bearing limestones from two properties. Research on samples from other areas is still underway.

Jan 1, 1957

By P. G. Shewmon

Radioactive MgZA has been used to study the rate of self-diffusion in oriented single crystals of magnesium in the temperature range 468O to 635OC. The diffusion coefficients parallel and perpendicular to the c-axis are: Dl, = 1.0 exp (—32,200IRT) cm2 per sec and Dl = 1.5 exp (—32,500IR T) cm Qer sec. The ratio Dl/Dll was found to vary from 1.13 at 468 to 1.24 at 575 C. Assuming a vacancy mechanism, an explanation of this aniso-tropy of diffusion follows from a consideration of the difference in the saddle points for diffusion in and out of the basal plane. RECENT discovery of radioactive Mg2"'-' has made possible the study of self-diffusion in magnesium. The experimental procedure and the results of a study of diffusion in polycrystalline magnesium have been described in an earlier paper.V he present work is an application of the same techniques to the study of self-diffusion in oriented single crystals of magnesium. In the general diffusion problem the diffusion coefficient is a second order tensor relating the two vectors, the diffusion flux, and the concentration gradient. In a hexagonal lattice, such as magnesium, the complete determination of the diffusion coefficient D as a function of direction in the lattice requires a knowledge of D,, and D,, i.e., the diffusion coefficients parallel and perpendicular to the c-axis, respectively. It can be proven quite generally that in a hexagonal lattice D is independent of direction in the basal plane, and that out of the basal plane it varies with 0, the angle between the c-axis and the direction of diffusion, according to the equation D(B) = D,,cos2B + D,sin2B. [I] The proof of Eq. 1 depends only upon the symmetry elements of the hexagonal lattice and upon the transformation properties of a second order tensor." Therefore, Eq. 1 holds for any mechanism of diffusion and any c/a ratio. Experimental Procedure The experimental procedure used with polycrystalline specimens can be briefly outlined as follows. Radioactive Mg" was produced by bombarding a NaCl crystal with 350 mev protons and was chemically separated from the target as MgO. The Mg" was then vapor deposited on a specially cleaned magnesium specimen by heating the MgO on a tantalum ribbon in a vacuum. During the diffusion treatment, oxidation and vapor loss of the radioactive material were minimized by annealing the samples in pairs with the active faces in contact, each pair being inside a magnesium container, which was in turn surrounded by an argon atmosphere in a sealed Pyrex tube. The distance-activity profiles were obtained by measuring the activity of thin sections cut parallel to the original interface with a lathe. The only technique which was peculiar to this work was the preparation and orientation of the single crystal specimens. The single crystals used in this work were grown by E. C. Burke of the Dow Chemical Co., using a modified Bridgman method, in which the furnace and specimen were stationary while the temperature gradient moved.' In growing these crystals the starting material was distilled magnesium, the crucibles were machined from Acheson electrode graphite, and the furnace atmosphere was tank argon. The crystals were grown from sublimed magnesium with the following analysis: 0.0002 pct Al, 0.0017 pct Fe, 0.0009 pct Mn, 0.0001 pct Ni, 0.0006 pct Pb, and less than 0.01 pct Ca, 0.0001 pct Cu, 0.001 pct Si, 0.001 pct Sn, and 0.02 pct Zn. The two crystals used were roughly lh in. diam and eight in. long. The c-axis made angles of about 7" and 78", respectively, with the specimen axes. If the values of D obtained by the use of these two crystals are taken equal to D,, and D,, respectively, the error introduced by this assumption is less than 1 pct. This can be shown by combining Eq. 1, the identity sin% + cos'8 = 1, and the experimental fact that DJDn in magnesium was always less than 1.25.

Jan 1, 1957

By K. K. Kershner

The purpose of this investigation was to develop methods on a laboratory scale for recovering tin from metallurgical slime, Tin chlorides were volatilized using mixtures of hydrogen chloride and reducing gases, such as hydrogen, carbon monoxide, hydrogen sulfide, ethane, propane, and butane. Optimum conditions were found to be n mixture of 3:1 of hydrogen and hydrogen chloride at 475° C. Over 95 percent of the tin was volatilized as chlorides. Low temperatures and relatively rapid rates of reaction are distinct advantages of the chloride volatilization process. Research is being continued with various slimes and will be extended to tin ores, where the method offers interesting economic possibilities in comparison with current tin-smelting practice.

Jan 1, 1957

By F. H. Deily, H. W. Lownie, E. A. Loria, L. W. Ledgerwood, M. W. 207-000-000-012 Mallett, J. E. Eckel

MANY investigations have been made of the residual gas content of iron and steel. Very few, if any, quantitative measurements have been made on the oxygen content of cupola-melted iron.' The fact that cast iron is a complex alloy rather than

Jan 1, 1957

By C. A. Kumke

The Korean crisis and the cessation of Russian manganese-ore shipments to the United States in 1950 reemphasized the almost total dependence of the domestic steel industry on foreign supplies for metallurgical-grade manganese ore. In this emergency, Congress authorized the Bureau of Mines to undertake experimental mine and process development work on the known large reserves of low-grade manganese ore in the Artillery Mountains region in Mohave County, Ariz. The objective of the work was to obtain the basic mining and metallurgical data needed to make specific plans for initiating exploitation of the deposits within 3 years if high-grade foreign ore could not be obtained during the emergency. The manganese deposits of the Artillery Mountains region are in an area of about 25 square miles on the north side of the Bill Williams River in southern Mohave County. Lasky, of the Federal Geological Survey, has estimated reserves at 175 million tons of manganiferous material assaying 3.5 to 4 percent Mn. Although the man¬ganese occurs in various Tertiary and Quaternary formations as both bedded and fissure vein deposits, the more important syngenetic deposits are found in upper and lower manganiferous zones in the sedimentary beds of playa and alluvial fan origin that constitute the Chapin Wash formation.

Jan 1, 1957

By R. W. Huber

A consumable-electrode arc-melting furnace was constructed at the Bureau of Mines Physical Metallurgy Laboratory, College Park, Md., for the production of uncontaminated titanium and titanium-alloy ingots. The furnace was designed to allow for evacuating to very low pressures and back filling with helium and argon mixtures for melting at or near atmospheric pressure. Vacuum melting at a few millimeters pressure was also used with a mixture of helium and argon gas sweeping the crucible. For research purposes a 25- to 30-pound ingot, 4 inches in diameter by 15 inches in length, was selected to provide, enough 1/2-inch plate for extensive tensile and impact testing of standard size specimens. Enough plate was also provided for testing by other Government laboratories. The homogeneity of several alloy ingots was determined, and excellent results were obtained. By using a large electrode-to-ingot-area ratio and high currents or power inputs to the arc furnace rather uniform ingots were routinely prepared.

Jan 1, 1957

By James H. Bechtold

The yield strength of annealed tungsten was found to have a strain rate exponent 12 times as great as that of low carbon steel. The effects of temperature and strain rate could be correlated through the Zener-Hollomon parameter with a heat of activation associated with yielding of 32,000 cal per g-atom. This heat of activation is independent of strain although both the temperature and strain rate dependence of the yield strength vary with strain. MOST metals have mechanical properties that are relatively insensitive to strain rate, especially at temperatures below that at which creep is important. In iron and molybdenum," however, relatively large strain rate effects are observed in the temperature range where the rapid increase in yield strength occurs which leads to the ductile to brittle transition. In this temperature range Zener and Hollomon' have suggested that the effects of strain rate and temperature T on the yield strength could be correlated through a single parameter, P, in the following manner where Q is a heat of activation characteristic of the metal and associated with some unspecified relaxation process. They also observed that if the temperature is restricted to a relatively narrow range— below room temperature for steel—that the logarithm of the yield strength could be expressed as a linear function of the logarithm of P. From this relation the logarithm of stress should be a linear function of the logarithm of the strain rate at constant temperature: where r will be referred to herein as the strain rate exponent. At a constant strain rate the logarithm of stress should be a linear function of l/T, ay(e = C) ~ eT [4] where q = Qr [5] and is referred to herein as the temperature exponent. These equations have been found to relate the effects of temperature and strain rate on the yield strength of molybdenum in the temperature range wherein the ductile to brittle transition occurs, —75° to +150°C.2 Bechtold and Shewmon3 have shown recently that the ductile to brittle transition in annealed tungsten occurs in the temperature range +150° to +350°C. In this temperature range the yield strength in-

Jan 1, 1957

By H. L. Sauder, J. L. Newman, C. Waddell

An instrument capable of measuring subsurface flow rates is described. The instrument is self-contained and may be run on piano wire line. It detects flow by means of an impeller suspended between two torsion wires. The force of the well fluid striking the impeller causes the impeller to rotate, exerting a torsional force to the wires. This force is determined by recording the angle of rotation of the impeller on film using a battery-driven, clock-controlled camera. The impeller is sensitive to flow in either direction and the same instrument can be used to measure injection as well as production rates. Changes in direction of flow, such as might be caused by thief zones, are measurable and are indicated by a reversal of the direction of rotation of the impeller. Adjustment of the sensitivity of the instrument to measure a wide range of flow rates is accomplished by the use of different size torsion wires. An umbrella-type fluid trap, which contacts the casing or wellbore, diverts the flow through the flow tube. The fluid trap remains closed while rurrning in the hole and can be opened at any point in the well. The instrument with the trap closed is 1 3/4 in. OD and may be run through 2 in. tubing. Successful flow profiles have been made on wells with flow rates ranging from 60 BID to 4,000 B/D at surface pressure up to 4,500 psi. The instrument is designed for high-pressure and high-temperature operations. INTRODUCTION The need for an instrument that will measure flow rates in a wellbore is as old as reservoir engineering itself. A number of such devices have been designed within the past few years. Some of these have been described in the literature1,2,3,4,5,6 One of these devices1. a hot-wire anemometer type, made many successful jobs in dry gas producing areas. Difficulty was encountered when this flowmeter was used in wells producing liquids and development work was initiated to overcome this difficulty. The present flowmeter is the result of this work and provides an instrument with a wider range of application in the industry. Consider- able development work has been done on the tool involving many changes in the mechanics of recording the flow readings, however, the basic principle of flow detection has remained the same since its inception. PRINCIPLE OF OPERATION The basic principle of operation of the flowmeter is the utilization of a portion of the kinetic energy of flowing well fluid to impart a rotational force to an impeller suspended between two torsion wires. This impeller, Fig. 1, is a screw-type propeller with the blades having a pitch angle of 40. As the well fluid passes through the instrument it strikes the impeller. The resulting force rotates the impeller and twist\ the torsion wires to a balance point at which the torque imparted to the wires balances the force required for the impeller to deflect the well fluid. The impeller is symmetrical and a change in direction of the flow results in a reversal of the direction in which the impeller is deflected. Thus the direction of the flow as well as its velocity is indicated. A dial is attached to the impeller by means of a hollow tube through which the upper torsion wire extends. The angular position of the impeller is recorded by photographing the dial at frequent intervals. In any given set of torsion wires the modulus of shear and polar moment of inertia remain constant and the deflection varies directly with the applied torque. The deflection imparted to the torsion wires also varies as the square of the fluid velocity. Further, the velocities represented by any two given deflections hear the following relationships: and Where V = velocity of flow stream and O ;= deflection. This is the basic relationship which is used to calculate the relative velocities represented by a given set of deflections where the velocity represented by any one of the deflection readings is a known quantity. For a given torque, the deflection of the torsion wire varies inversely as the fourth power of the wire diameter. Wire sizes ranging from ,005 in. in diameter to .022 in. in diameter can be used. The range of

Jan 1, 1957

By C. S. Matthews, M. J. Fischer

Distortions caused by dip on five-spot sweep pattern were determined by visual experiments on a model composed of parallel plates of glass with holes drilled at the well positions. This model war designed to simulate a reservoir depleted of its primary oil and containing a gas phase. Prior to interference, it was found that the injected fluid took a nearly circular shape about the injection well for the cases studied. However, these circles moved down-dip considerably under the influence of gravity. It was concluded that pattern flooding should be practical for many dipping reservoirs. A quantitative measure is given of how much the well position should be altered to allow for dip. Experimental deternzinarions of injectivity showed this to be about the same in a dipping reservoir as in a horizontal one. INTRODUCTION This investigation was undertaken at the suggestion of the Pacific Coast area, Shell Oil Co., where a pilot water flood in a dipping reservoir was being carried out at the time this paper was in preparation. Prior to the undertaking of this flood there had been considerable speculation as to how gravity would distort a flood pattern in a dipping reservoir. The thought was expressed in some quarters that a five-spot flood would not be applicable to a dipping reservoir because the flood pattern would elongate in the direction of dip and would never form a "seal" around each five-spot. If the flood pattern elongated sufficiently, both the oil and the water might flow largely downdip rather than into the pattern producers. In view of the importance of the California water floods, it was deemed important to determine the effects of gravity on a five-spot pattern in a dipping reservoir. Previous work had also been carried out in this laboratory,1 but only for the single-fluid case. The present investigation extends these results to multifluid cases. Several sets of pictures of flood fronts are presented so that the process can be visualized. From these pictures, curves are obtained which show the correct drilling position for achieving equal times of oil-bank breakthrough. Several injectivity curves are also presented which may aid in prediction of injection rate. ASSUMPTIONS The present results were obtained with a model composed of two parallel plates of glass spaced about 1 mm apart. When the inertial forces are small, as in these experiments, the flow between the plates follows Darcy's law and is analogous to flow through porous media. In using these plates, it is not possible to scale effects of capillarity correctly as regards a transition zone between injected and displaced fluid. Calculations show, however, that effects of such capillarity should not be important in determining the gross flooding pattern in the field. In fact, in this model the capillary forces tend to circularize the pattern to a greater degree than in the field. To preserve a large ratio between the viscous forces and the circularizing capillary forces in the laboratory model, viswus glycerine was used as the flooding liquid and the rate of flooding was very high. The circularizing force is believed negligible in these experiments. In addition to the effect of the surface tension y, which tends to circularize the pattern, another capillary force must be considered. This is the adhesion tension y cos, which acts at right angles to the circularizing term y. If the plates in the model are "wetted" the same all around the periphery, then the adhesion tension,

Jan 1, 1957

By G. Sachs, E. P. Klier, W. Beck

HYDROGEN embrittlement of steels has recently attracted much attention because it is asso- ciated with a variety of failures, especially those of aircraft structural components.' For instance, one of the undesirable properties of the ultra-high strength steels used for landing gears is their pronounced susceptibility to hydrogen embrittlement during plating. The presence of hydrogen in these steels becomes particularly apparent through delayed or sustained load failures of parts which have been subjected to low loads for an extended time. A number of variables are involved in causing a reduction of strength and ductility through hydrogen

Jan 1, 1957

By Daniel M. Bass, Paul B. Crawford

Laboratory investigations have been made to study the effect of variations in fluid characteristics, gas saturation, water saturation, and water injection rate on oil recovery by water flooding. Three synthetic gas-saturated crude oils having bubble points of 860, 1,540 and 1,885 psi were used as reservoir fluids. Repeated tests were made in which a and pack, saturated with water and synthetic oil, was produced by solution gas drive followed by water flooding at various pressure levels. Oil recovery by solution gas drive and subsequent water injection is shown to vary with the pressure and rate at which the water flood is conducted. The pressure at which optimum flooding conditions exist is shown to be a functiotl of the physical characteristics of the reservoir fluid. For the systems studied, increases in oil recoveries of near 10 per cent were obtained by flooding at the most desirable conditions. Va- riations in initial water saturations gave results similar to those in the literature. INTRODUCTION Most of the waterflooding studies investigating means of improving present exploitation processes have been conducted at low pressures with little effort to simulate reservoir conditions. Holmgren and Morse' performed a waterflooding study at 300 to 500 psi wherein the gas saturation was created by injecting gas, letting dissolved gas evolve from the oil, and then flushing the core with "live" oil until the desired gas saturation was obtained. Their results show increasing oil recoveries with increasing gas saturations. Data presented by Guerrero' and Kennedy, et al, indicate that in some instances water flooding at approximately 500 psi below the original bubble point results in a lower residual oil saturation than is obtained when water flooding above the bubble point. In their work gas saturations were created by primary depletion. By correcting low pressure flooding data for fluid shrinkage, Dyes found that a maximum oil recovery may be obtained by flooding with initial gas saturations of from 7 to 12 per cent. The purpose of this work was to determine the variations in oil recovery caused by initiating a waterflooding program at various stages of primary depletion of a core. This is a part of a more comprehensive study of obtaining criteria for determining when to initiate a pressure maintenance program and what fluids to in-ject. EQUIPMENT A schematic diagram of the apparatus is shown in Fig. 1. Fluid transfer was accomplished with metering pumps. Pressure control was ob-

Jan 1, 1957

By J. H. Walsh

IN THE DEVELOPMENT of procedures for the separation of minerals, the choice of reagents for flotation is frequently determined by the extent to which a given mineral is wettable by water. Measurements of the contact angle of an air bubble on wet mineral surfaces are often used in the laboratory to estimate the wettability of the surface. For the results of these measurements to be reproducible, the surface of the mineral must be polished to a mirror-like smoothness and must be free from oily contamination. Elaborate procedures for preparing mineral surfaces have been developed by Wark ( 1) and Taggart (2), and these procedures have been generally accepted as adequate for their purpose. The polishing techniques, how-ever, have certain inherent disadvantages which make it impossible to assess the effects of polishing, entrained abrasive, and adsorbed gases on the wettability of the mineral surface.

Jan 1, 1957

By Parkhurst D. H

It is shown that a differential colorimetric technique can be used as a routine method for the estimation of titanium in beach sands, and their ore dressing products. The method will tolerate the presence of most of the other elements usually found in beach sands. The accuracy is shown to be within the limits of ±0ò31 per cent for concentrates containing more than 95 per cent titanium dioxide and ±1 per cent for tailings containing 0ò2 per cent titanium dioxide. The method is described for use with a Hilger "Spekker" absorptiometer.

Jan 1, 1957

By G. E. McElroy

Ventilation-pressure surveys are required to determine the rates of pressure losses in various parts of mine-airway systems. These may be determined directly by differential pressure measurements or deduced from absolute pressure measurements, Despite the confusion caused by its inverted nonlinear scale, the altimeter has special application to pressure surveys in mines in which only small differences in elevation are involved, as is true for most of our large bituminous-coal mines in these, the judicious use of information obtained by pressure surveying can result in greatly improved working conditions as regards health and safety and, in many instances, can yield large financial returns. The main purposes of this report are to discuss methods of using altimeters for pressure surveys and to present the particular methods of making surveys and calculating the results of surveys used by the Mine Ventilation Section of the Bureau of Mines.

Jan 1, 1957

By Robert F. Pettit

This paper on methods and costs of mining and milling iron ore at the Iron Mountain mine of Ozark Ore Co., St, Francois County, Mo., is one of a series of Bureau of Mines reports on methods, practices, and costs of mining and milling throughout the United States. The Iron Mountain operation is notable for its successful transition from open-pit to underground mining, for use underground of large earth-moving equipment, and for development of a multilevel room-and-pillar mining method. Milling methods also have undergone transitions - from hand sorting and log washing in the early days to gravity concentration. Milling ultimately may include flotation to recover additional iron from products now discarded as tailing,

Jan 1, 1957

By Elmars Ence, Harold Margolin

The Ti-Fe and Ti-Fe-0 systems were re-examined because of the controversy regarding the existence of Ti2Fe, and to consider all available data points to the existence of Ti,Fe. The Ti-Fe-0 system contains two ternary compounds: E, corresponding to Ti2Fe; and y. SEVERAL authors have investigated the constitution of titanium-rich alloys of the Ti-Fe system. The most extensive study of titanium-rich portions of the Ti-Fe system was by Van Thyne, Kessler, and Hansen,' who investigated this system up to 50 pet Fe and used the highest purity materials available for their alloy preparation (iodide titanium was used for alloys up to 20 pet Fe). According to Van Thyne et al., phase relationships in the region of investigation are governed by phases a,ß, and TiFe. No evidence of an intermetallic compound Ti,Fe was found. although earlier. works by Laves and Wallbaum,' and Duwez and Taylor' reported its existence. Rostoker's study on the occurrence of TilX phases" confirmed the findings of Van Thyne et al. Rostoker proposed that the compound Ti Fe found by Duwez does not exist but is actually a ternary compound, Ti1Fe3O, originated by inadvertent oxygen contamination. The partial isothermal section of the ternary Ti-Fe-0 system as reported by Rostoker' seems to confirm this explanation. In the course of phase diagram work conducted at New York University, however, certain irregularities were observed to be associated with ternary systems of the type Ti-Fe-X. The ternary phase 6, observed in the systems Ti-Fe-Mo' and Ti-Fe-V." was found to be structurally identical to the com-pound Ti2Fe as reported by Duwez and Taylor, and to Rostoker's compound Ti1,Fe2O. Since the amount of oxygen possibly present in the Ti-Fe-Mo and Ti-Fe-V systems could not account for the observed amounts of the compound, it appears that the d phase in these systems is not Ti,Fe,O. On the other hand, considering the amounts of the 6 phase, particularly in the Ti-Fe-Mo system, the location of the phase was uncertain. It was felt that the introduction of the Ti2Fe phase would alleviate some of the inconsistencies of the two systems. Because of the uncertainties relating to the phase Ti2Fe, or Ti1Fe2O, it appeared worthwhile to re-examine the Ti-Fe and Ti-Fe-O systems in the vicinity of these compounds with highly sensitive metallographic techniques and with X-ray methods. Experimental Procedure Alloy Preparation—For the study of the binary system four alloys were prepared, containing 26.9 (30 wt pct), 34.0 (37.5 wt pet), 41.2 (45 wt pet), and 56.3 (60 wt pet) atomic pet Fe, and for the ternary Ti-Fe-O system 18 alloys were prepared in the composition range of 1.6 to 16.9 atomic pet 0 and 24.3 to 55.7 atomic pet Fe. The materials used for the Ti-Fe alloys were iodide titanium (99.98 pet Ti, 0.002 pet 0) and Ferro-vac-E iron (99.95 pet Fe, 0.0052 to 0.0072 pet 0). For the Ti-Fe-O study the materials used were sponge titanium containing less than 0.06 pet 0, Ferrovnc-E iron, and Baker's analyzed TiO2. The nominal weight and atomic percentages of the ternary alloys prepared are shown in Table I. Melting—Charges of 10 to 15 g were melted in a nonconsumable arc furnace in argon atmosphere according to the technique described elsewhere.'" Since there was practically no weight loss through the various stages of melting and oxygen losses have not been observed previously, it appeared justifiable to use nominal composition for interpretation of data. Iodide titanium control buttons, of the same mass as the Ti-Fe charges, and melted under the same conditions, were used to check hardness pickup during melting. A hardness increase of 2 to 3 Vhn was found. Heat Treatment—The specimens were annealed in quartz capsules under argon. To avoid contact between the specimen and capsule material all specimens were wrapped in titanium sheet. The annealing times are given in Table 11. The attain-

Jan 1, 1957

By Peter Greenfield, Paul A. Beck

Thirty binary systems of vanadium and chromium group transition elements with second and third long period transition elements were explored in regard to the intermediate phases formed. It was found that the phases predominating in these systems are s, AB type with ordered a-tungsten or C8 structure, close-packed-hexagonal with small unit cell dimensions and, finally, phases isomorphous with 1-manganese. IN recent years, considerable information has become available concerning the intermediate phases in binary systems of the transition elements. Thus, the s phase has been found to occur in most of the binary systems of vanadium, chromium, and molybdenum with the group of elements manganese, iron, cobalt, and nickel.' It was observed that, while the rr phases formed by chromium with manganese, iron, or cobalt possess a considerable temperature range of stability, particularly in the Cr-Co system, the corresponding s phases with molybdenum are limited to a temperature range of less than 400" above about 1200°C. Goldschmidt' reported v phases of tungsten with iron and cobalt, and these are apparently stable only at (and above?) 1400°C." Exploratory work in this laboratory with Fe-W and Co-W alloys of approximately 60 atomic pct W annealed at 1300°C did not produce X-ray patterns suggesting the presence of a phase. It appears then that the phases of iron and cobalt with the chromium group elements decrease in stability as the two components are chosen from long periods further removed from each other. From the available information, it might be concluded that the controlling factor is the increasing difference in atomic radii between the components. In contrast to the a phase, the phases formed by iron and cobalt with chromium group elements' are stable only when the latter have large atomic radii (molybdenum and tungsten); the corresponding phases with chromium do not occur. When the difference in atomic size becomes still larger (r,/r,, approaching the ideal value of 1.225), the u and p phases are replaced by Laves phases (AB,), as in the alloys of iron and cobalt with columbium," tantalum." and titanium."-" However, atomic size certainly cannot be the sole determining factor, since, for instance, in contrast to the very stable (Mo, Co)p phase, no such phase occurs in the Mo-Ni system even though the atomic diameters of cobalt and nickel are nearly the same. Similarly, chromium and cobalt form a a phase in a wide temperature range," but the corresponding s phase in the Cr-Ni system is missing. It has been shown that the composition of the u phase in various binary and ternary systems of transition elements in the first long period may be correlated in a fairly quantitative manner with the number of electron vacancies. The influence of electronic structure is probably present also in binary and ternary phases' and to some extent, apparently, even in Laves phases." " Although the absence of phases in the Cr-Ni and Mo-Ni systems has not as yet been explained on the basis of electronic structure, it appears reasonable to suspect a connection. One of the great difficulties in arriving at well founded rules in regard to the alloying behavior of transition elements lies in the lack of reliable information concerning the details of their electronic structure in the metallic and alloy form. The theoretical penetration of this field appears to be beset by very considerable difficulties, even when the complications due to alloy formation are disregarded. Another great source of uncertainty is the scarcity of phase diagram information even for binary systems of the transition elements so that only a very limited basis is provided for generalizations as to the occurrence of intermediate phases. For instance, very few binary phase diagrams of second and third long period transition element systems have so far been published. The present work was undertaken in order to survey the various types of intermediate phases occurring in 30 binary systems of elements of the group vanadium, columbium, tantalum, chromium, molybdenum, and tungsten with the elements rhenium, ruthenium, rhodium, palladium, and platinum. For most of these binary systems phase diagrams are very incompletely or not at all known, as will be further reviewed.*

Jan 1, 1957

By Howard Martens

HARDNESS behavior of commercial titanium alloys following various heat treating processes has been studied for some time. However, the hardness of such alloys following a definite measured cooling rate from the single phase region has not been reported. Therefore, a series of experiments was conducted on the three alloys: 150A, 130A, and 130B. The manufacturers gave the following compositions for these alloys: Ti 150A: 0.045 pct C, 0.069 pctN, 1.32 pct Fe, and 2.68 pct Cr; RC 130A: 0.13 pct C, and 7.9 pct Mn: RC 130B: 0.11 pct C, 3.5 pct Mn, and 3.2 pct Al. A method similar to that described by Greninger was used, and the cooling rate varied from 6" to 9200°F per sec. The cooling curves were recorded on a Speedomax or a recording oscillograph, and the hardness was measured on a Tukon hardness tester using a Knoop indentor with a 500 g load. The curves of Fig. 1 show the variation of the Knoop hardness with the cooling rate for these three alloys. The alloys 150A and 130B behave in a similar manner, as shown by the curves. In neither of these alloys was it; possible to retain the high temperature ß phases, even by the most rapid cooling rate. The slow cooling rates produced a typical ß structure in these two alloys. As the cooling was increased, these phalses became more finely dispersed and the hardness increased. This increase in hardness with cooling rate continued for the 150A alloy until a rate of approximately 1000°F per sec was reached. At this cooling rate, the structure showed the result of the dif-fusionless transformation of the ß solid solution to the supersaturated a solid solution which is referred as a'. At higher cooling rates, the structure showed no change and the hardness showed no great change, as indicated by the dotted portion of the curve in Fig. 1. The increase in hardness with cooling rate for the 130B alloy continued until a rate of approximately 300°F per sec was reached. At this rate the structure was produced and the maximum hardness was reached. Higher cooling rates caused no marked changes in hardness or structure. The alloy 130A behaved in a different manner, as shown by the curve of Fig. 1. The structure produced by the slow cooling rates was a typical a+ß structure, which became finely dispersed as the cooling rate increased. The hardness increased with cooling rate and reached a maximum at approximately 120°F per sec. At this maximum hardness, the structure showed the result of the decomposition of the ß phase into the ß + phase structure. As the cooling rate was increased, smaller amounts of the at phase were formed and the alloy became softer. For cooling rates of 3000°F per sec and above, the high temperature ß phase was retained and the hardness of the alloy did not change markedly. Acknowledgment This paper presents the results of one phase of research carried out at the Jet Propulsion Laboratory, California Institute of Technology, under Contract No. DA-04-495-0rd 18, sponsored by the Dept. of the Army, Ordnance Corps.

Jan 1, 1957

By L. D. Hall, S. J. Rothman

The diffusion of lead and of trace amounts of bismuth in liquid lead have been investigated by the capillary method, using ROD and ROE as tracers. The results are compared with existing theories of diffusion in liquids, the agreement with theory being fair. The heat of activation for self-diffusion in lead is found experimentally to be close to the corresponding activation energy obtained from viscosity data. The pioneer data of Groh and von Hevesi for the self-diffusion of liquid lead, using ThB as a tracer, fit in with the present results. OMPARED with the volume of effort expended on solid state diffusion, there has been little attention paid to diffusion in liquid metals. A review of experimental work in this field, covering most of the studies up to 1951, was given by Jost.' More recent papers include those by Hoffman2 on self-diffusion in mercury, Morgan and Kitchener" and Stark, Shchilishchev, and Kazachkev4 on the diffusion of various elements in liquid iron, and Grace and Derge on the diffusion of bismuth in bismuth-lead alloys. The need for more experimental data to aid in the evaluation of existing theories prompted the

Jan 1, 1957

By W. H. Oppelt

A small, annular-retort gasifier having a nominal capacity of 40 pounds of lignite per hour was designed and constructed at the Lignite Experiment Station, Grand Forks, N. Dak. The purpose of the investigation was to increase the capacity of an annular-retort gasifier by better temperature distribution in the heating chamber (adjacent to the annulus) and by supplemental internal heating with controlled amounts of air. Correct control of air admission should yield crude ammonia-synthesis gas having a (H2+CO)-N2 ratio of 3. Dakota Star stoker-size lignite was used during the exploratory experimental program. The effects of temperature level and distribution in the heating chamber and of addition of air to the reactor were investigated. Hydrogen - carbon monoxide ratios ranged from 1.9 to 2.5, and (H2+C0)-N2 ratios were as low as 2.9. Hourly gas production ranged from 970 to 2,580 cu. ft., or 62.0 to 164 cu. ft. per sq. ft. of heated surface, or 350 to 940 cu. ft. per cu. ft. of reactor volume. Data from the small gasifier could be readily correlated with those previously obtained in the commercial-scale unit under comparable experimental conditions.

Jan 1, 1957