Search Documents

By D. W. Levinson, L. F. Mondolfo, N. A. Gjostein

MANY investigations are reported in the literature on the age hardening of Al-Mg-Zn alloys but most of them are concerned mainly with mechanical property changes. The present investigation was started to determine the structural changes in an AlMgZn alloy. The alloy composition was chosen in the existing phase diagram" so as to lie on the quasi-binary section Al-(AlZn)Mg Actually, it was found that the diagram as published was inexact at the lower temperatures and that the phase in equilibrium with aluminum at the lower temperatures is not the ternary compound. Technique The alloy used for the investigation was prepared from high purity materials and the resulting composition as determined by chemical and spectro-graphic analysis was: Zn, 6.17 pct; Mg, 2.13 pct; CU, 0.03 pct; Si, 0.009 pct; Fe, 0.005 pct; and the remainder, aluminum. An ingot -in. thick was cast, homogenized, hot and cold-rolled to strip 0.064-in. thick for dilato-metric and powder work, and to foil 0.005-in. thick for single crystal work. Solution treatment temperature for all specimens was 475°±5°C for periods of at least 1 hr, either in air furnaces or lead baths. Aging was done in oil or Pb-Bi baths controlled to within ±3°C. The aging was investigated at the following temperatures: room (30°), 130°, ZOO0, 260°, and 300°C. For the dilatometric study, the length changes were measured continuously, at temperature, using strips of alloy 10 in. long, shaped as channels to eliminate undesirable deflection due to bending. To compensate for thermal expansion and contraction due to the variations in the temperature of the aging baths, the dilatometers were built of the same alloy as the one being tested, with the same shape and size, but with material fully annealed. Gages on which 0.0005 in. could be read and 0.0001 in. estimated were used to measure the dilation. Length changes were also measured at room temperature. Strips approximately 10 in. long were solution-treated, quenched, and measured in a supermicrome-ter in which 0.0001 in. could be read and 0.00001 in. estimated. The specimens were immediately aged for a given time, remeasured, and then the cycle was repeated, including the solution treatment. The error of measurement with this technique was somewhat larger, but the results confirmed those obtained by continuous measurements. The sheet used for the dilatometric work was checked to determine grain orientation. Both X-rays and etching methods revealed a rather coarse grain size but only a negligible amount of preferred orientation. Thus, volume changes calculated from length changes are not invalidated by preferential orientation effects. Pieces of the sheet used for the dilatometric work were also used for the metal -lographic work. Filings for the powder X-ray study were produced from a homogenized piece of sheet. These filings were magnetically purged of iron, screened to 200 mesh, sealed in a Pyrex tube containing an argon atmosphere, and solution-treated. When quenching, the glass tube was broken, so that the powder dropped directly into cold water. After drying with alcohol, the powder was sealed into capillary tubes containing an argon atmosphere and then aged for the required times. In spite of all these precautions the three strongest lines of a( Al2o) appeared in all patterns, and were used as internal standards. By the use of these standards, accurate corrections for film shrinkage were obtained. For the back reflection patterns, annealed nickel powder was mixed with the specimen to act as internal standard. A preliminary investigation was made in small (57.3 mm diam) powder cameras. From these patterns the changes which took place in the solid-

Jan 1, 1957

By P. W. Neurath

IN recent years the domain theory of ferromag-netism has been put on a sound experimental and theoretical basis. But its application to one of the most widely used high quality magnetic materials, the cold-rolled grain-oriented 3 pct Si-Fe used in transformer cores, has been rather difficult because of the complexity of the domain structure of the poly crystalline sheet material. This paper presents some experimental data for this material, showing the relation between plastic and elastic stresses, 60-cycle watt losses, and the domain structure as observed visually. Only a very tentative qualitative explanation of the effects will be attempted. Some initial results were reported earlier.'

Jan 1, 1957

By Joseph J. Yancik, Leonard L. Felts, George B. Clark

LITTLE information has been published concerning the actual or useful amount of energy obtained from explosives when they are used for blasting. To provide more data on this subject, 8-in. neet cement cubes were blasted in a steel plate box and the breakage energy evaluated by comparison with drop crusher results using Rittinger's,1,2 Kick's: and Bond's' theories. Theories by Bond and Wang," Lineau," Hatch,' Roller,' and others0-11 were not considered applicable. Those used in this investigation may be expressed mathematically as follows: Rittinger Theory E = KrS2, pet,—--------------- [1] 40 d1 d0 Kick Theory TV 1 1 E = =K, [S pct. log1/d+ 100 log d0] [2] 40 d1 L. L. FELTS, Junior Member AIME, was formerly a Graduate Assistant, University of Illinois. G. B. CLARK, Member AIME, was formerly Professor of Mining Engineering, University of Illinois, and is now Chairman, Dept. of Mining Engineering, Missouri School of Mines and Metallurgy. J. YANCIK, Junior Member AIME, is a Graduate Assistant, Missouri School of Mines and Metallurgy. This paper, TP 4213A. is revised from a thesis submitted by L. L. Felts in partial fulfillment of the M.S. degree in Mining Engineering, University of Illinois, 1954. Discussion may be sent (2 copies) to AIME before May 31, 1956. Manuscript, Dec. 27, 1954. Bond's Third Theory E = Kb [S pct. log1/d1+ 100 log d0] where E — energy used in breakage, d, = average diameters of screen fractions of broken cement particles, pct, = percent weight of diameter d;, and 2 pct, = 100 pct. The above equations were employed to determine values of Kr, Kk, Kb for particle size distributions similar to those obtained from the blasting curves. These values were in turn used as a means of approximating the specific energy of the blasted material. The efficiency of crushing by blasting was then determined by dividing this specific energy by the maximum available work of the explosive per gram of cement. Knowledge of the failure of solids under static loads is developing very rapidly. Their failure under impact loads has been investigated and reported in the literature only to a limited extent. Theories of failure' hnder static loading include 1) the maximum stress theory, 2) the maximum strain theory, 3) the theory of constant elastic strain, 4) theory of maximum shearing stress, and 5) Mohr's theory of strength. All of these have elements of usefulness in establishing an applicable theory for blasting. For highly strained and compressed material such as that surrounding a detonating charge of high explosive, the Mohr theory and its implications appear to be the

Jan 1, 1957

By V. A. Nieberlein

An extractive process was developed applicable to submarginal titanium deposits containing valuable minor constituents; such as columbium (niobium) and iron. The process consisted of reducing the mineral concentrate with coke at high temperature to form a carbide-suboxide sinter, chlorination in the 400° -500° C. range, and fractional condensation of the chlorides. The chlorination procedure recovered 97, 83, and 87 percent of the titanium from brookite, rutile, and ilmenite sinters, respectively, while simultaneous columbium recoveries on the same materials were 85, 50, and 87 percent.

Jan 1, 1957

By L. L. Mohier

Mr. Vissac's study is very elaborate and complete and gives a clear idea both of phenomena occurring during operation of the feldspar jigs and results ob- tained by some of them in Europe. I have no intention of going into a complete discussion, but I would like to give a few comments about these results already

Jan 1, 1957

By Chester T. Sims, Robert I. Jaffee

The thermoelectric behavior of the Pt—Pt-Re thermocouple and the resistance of rhenium to attack by certain molten metals is discussed. In addition, data are presented on the stress-rupture behavior of drawn wire, the tensile characteristics of rolled sheet, the variation of Young's modulus with temperature, and the effect of specimen size and fabrication method on the work harden ability. Mechanical properties of thoriated rhenium are discussed. This includes data on the effect of thoria in rhenium on tensile properties, ductility, work hardening, and recrystallization. RECENT work by the authors', has described methods of fabrication and some of the physical and mechanical properties of rhenium. Rhenium was established as a high melting, dense, refractory-type metal with favorable mechanical properties. In addition, Todd and co-workers' and others" have studied such properties of rhenium as the work function, specific heat, and the resistance of rhenium to the water cycle. Revelation of these and other properties has led to serious consideration for application as electrical contacts, high temperature thermocouples, and wear resistant materials. chanical properties reported previously,' several additional examinations have been conducted. The stress-rupture behavior and the Young's modulus of rhenium have been investigated at elevated temperatures. Tensile data have been obtained for rolled sheet, and a study of the relative work hardening characteristics of rod, wire, and sheet has been conducted. Variation of Modulus of Elasticity With Temperature—The Young's modulus of a % in. diam annealed rhenium rod was determined from room temperature to 880"C (1620OF). The rod, approximately 6 in. in length, was activated in a transverse vibration apparatus suspended in a furnace. The resonance frequencies of the rod were measured and used to calculate the moduli values. The driven frequency was 569 cycles per sec, and a protective helium atmosphere was used. The data, plotted in Fig. 1, show that the modulus decreases in an approximately linear manner with temperature over the range tested.

Jan 1, 1957

By Oren C. Baptist

[Several new oilfields have been developed in northwestern Wyoming during the past 10 years, production is obtained from discontinuous, permeable sands enclosed within impermeable shales. The energy to drive the oil to producing wells in supplied by gas in solution in the oil. Most of the wells had high-initial potentials, but rates of oil production have steadily declined, indicating a dissipation of the driving energy and the possibility that large volumes of oil will remain unrecovered in the reservoirs. The studies reported in this paper were undertaken to develop laboratory data of the type most likely to be needed by persons studying the susceptibility of the Newcastle sand reservoir to secondary-recovery methods.]

Jan 1, 1957

By A. W. Demmler

RECENTLY, Chaudron,&apos; Montariol,2 and their co-workers published the results of their studies on zone-refined aluminum. They found their material to be capable of recrystallization at —50°C, but gave no data as to the percentage reduction or time required. Their material was found to be practically non-work hardening at room temperature, but after 96 pct cold work at a low temperature and storage in liquid nitrogen it was found to recrystallize to coarse grains in less than 3 hr at 20°C. Recently, a study was made of the room temperature recrystallization characteristics of zone-melted aluminum. An ingot 14 in. in length, with a 3hx3 in. cross section, was made in an extremely high purity graphite boat under an atmosphere of dried commercial argon. It was made by first passing the molten zone along the ingot of 99.99+ pct A1 15 times. At this point, the most impure 3 in. (the end toward which the eutectic forming impurities migrated) were replaced with more of the original starting material, and 15 more traverses were made. Each traverse of the zone along the ingot required approximately 3 hr. Three ingots were prepared in this identical fashion and the chemical analyses were made spec-trographically on two of these ingots, rather than on the one used in this investigation. The analyses were made at 1 in. intervals along the ingot, in duplicate. Over the purest 5 in. of the ingot, which were most important in this investigation, there was found an average composition of <0.00004 pct Cu, <0.0003 pct Fe, <0.0001 pct Si, and <0.0001 pct Mg. In addition, the following elements were not detected spectrographically even in the more impure end of the bar: manganese, zinc, nickel, chromium, titanium, vanadium, lead, tin, boron, beryllium, bismuth, gallium, zirconium, cadmium, antimony, cobalt, and molybdenum. The original ingot was given several cold reductions, with intermediate anneals in order to refine the grains. Owing to the extreme length resulting and the ease of deforming the material plastically, it was cut into eight equal lengths and identified as shown in Fig. 1, with the highest numbered section at the purer end (that enriched with peritectic formers). Section 6 was used in the exploratory work and was found to be of exceptionally high purity, giving more rapid rates of room temperature re crystallization than any previous aluminum studied at the Alcoa Research Laboratories. This fact suggested that the entire midsection of the ingot might be of very high purity. Accordingly, section 4 was chosen for the next study. A portion of it was rolled to cold reductions of 10, 25, 40, 60, 75, and 90 pct at room temperature, and the re-crystallization of each specimen was followed by X-ray pinhole transmission photographs. The other portion received the same treatment, except that both the specimens and the rolls were maintained at 160°F in the process of rolling. The latter ortion was retarded in its recrystallization as compared to the former, probably due to the stress relief effect of the warm rolling. Both of these portions of the fourth section were found to recrystallize at a considerably slower rate than did the sixth section.

Jan 1, 1957

By Norman Visnes

EARLY in 1954, as initial development of the Galena mine was being finished, plans for stoping operations became the foremost consideration of the operating management. The Galena is being operated under lease agreement with the owner, Vulcan Silver-Lead Corp. Started in 1947, the Galena is a deep level development of American Smelting & Refining Co. and Day Mines Inc. under the management of ASARCO, in the Coeur d&apos;Alene mining district. Lead mineralization was found on the 3000 level in 1950. In 1953 development on the 3000 level disclosed a siderite vein, later known as the Silver vein, which contains commercial quantities of silver in Tetrahedrite. This vein was explored on the 2800 and 2400 levels and later on the 3400 level, the lowest in the mine. Work above the 2400 level to date has indicated that the vein dissipates to weak mineralization, and ore values are uncertain above the 2200 horizon.

Jan 1, 1957

Jan 1, 1957

By James E. Hill

In the course of exploratory drilling during World War II by the Bureau of Mines under the Strategic and Critical Minerals investigations Program, a problem arose as to the ultimate disposal of the drill core resulting from that program. The difficulties experienced in obtaining factual information to evaluate mineral deposits examined (during that program) influenced the Bureau in a decision to catalog and store the drill cores for future reference. Initially, the drill cores were stored at the nearest Bureau of Mines station that had space available for the purpose. Recently the Bureau stations at Minneapolis, Minn., and Denver, Colo., were designated as the locations of permanent drill-core storage facilities. Drill cores that are retained from Bureau of Mines mineral-exploration projects are stored at these two locations and are given preference in selecting cores for storage. Drill cores are accepted also for storage from other Government agencies, State agencies, private companies, or individuals on the basis of available facilities and consistent with the significance of the core in relation to Bureau of Mines objectives and national interest. Selection and acceptance of such drill core are determined by the Bureau of Mines. The drill cores stored at the two locations are available for inspection by any person having a legitimate interest in the mineral deposits represented by the cores. Approximately 1,850,000 feet of drill core can be stared in the facilities now available to the Bureau of Mines. Approximately 475,000 feet of drill care is stored or scheduled for storage at Minneapolis, Minn., and 240,000 feet of core stored or scheduled for storage at Denver, Colo. A list of drill core now in storage at the Bureau of Mines core-storage facilities at Denver and Minneapolis is included as appendix A.

Jan 1, 1957

By J. Gordon Parr, D. H. Polonis

RYSTALLOGRAPHIC relationships between martensitic a&apos; (close-packed-hexagonal) and retained fi (body-centered-cubic) have been studied in binary alloys of titanium with manganese, molyb- denum, chromium, and iron.&apos;" In these investigations, the habit planes of the martensitic phase were determined, as well as the orientation relationships between martensitic and parent phases. In each alloy

Jan 1, 1957

By Robert D. Thomson

LISTED among strategic and critical minerals for stockpiling, mica is an important raw material in electronic and electrical equipment industries. Each year large quantities are consumed in the manufacture of television and radio tubes, radar sets, generators, transformers, electric toasters, and irons. Crude mica, which comes from the mine in crystals or in rough books of various shapes and sizes, is known as run-of-mine or book mica. Structural imperfections, impurities, rough edges, and defective laminae are removed by cobbing, rifting, and trimming to produce a marketable block mica or film mica.&apos; After the rough books have been hand-cobbed to remove adhering rock, dirt, and crushed or defective mica they are rifted, or split. In the U.S. a straight-bladed knife is generally used for rifting. Products of this operation are classed broadly as untrimmed sheet mica and scrap. Sheet mica is any relatively flat piece sufficiently free from physical defects to be cut or stamped into specified shapes for industrial use. Sheet mica is classed as block, film, and splittings. Block mica is not less than 0.007 in. thick with a minimum usable area of 1 sq in. Film mica is split from the better qualities of block mica to groups of specified thickness ranging from 0.0012 to 0.004 in. Splittings are sheets with maximum thickness of 0.0012 in. and minimum usable area of 3/4 sq in. As virtually no mica splittings are produced in the U.S., they will not be discussed in this report. Small, low quality block is subdivided as punch and washer. Punch mica is thumb-trimmed material large enough to yield a circular disk of at least 11/2 in. diam for stained quality mica and 1 1/4 to 2 in. for clear quality. Poorer lots, often referred to as washer mica, are also included in the general term punch mica. Trimming, the next step in processing sheet mica, removes broken and ragged edges, loose scales, and other major imperfections. Trimming may be done with a knife, sickle, shears, or fingers. In the U.S. it is usually done with a 3-in. linoleum knife to obtain a bevel-edged cut. If ragged edges are broken off with the thumb and fingers, the mica is called thumb-trimmed. Full-trimmed is rifted mica trimmed on all sides with all cracks, reeves, and

Jan 1, 1957

By C. H. Bowen

NDUSTRY needs a generally applicable means of defining average grain size and grain size distribution. Students of sediments hade explored this field, employing methods that might also prove useful in engineering problems. Before attempting to solve specific problems it is well to review the derivation of commonly used grade scales and the reasons for their selection. This aspect of the problem seems largely to have been lost, and a review of basic factors may suggest causes for failures in using size analysis data. Three facts are implicit in selection of a grade scale: 1) Most particulate mixtures are continuous distributions of sizes, and any grade scale that may be employed is an arbitrary means of visualizing that distribution. 2) For purely descriptive purposes, any grade scale, regardless of the rationality of the class intervals, will be satisfactory if it is accepted by a sufficient number of workers. 3) For analytical purposes, class intervals must be small enough to define the continuous distribution accurately. Further, where statistical studies are involved, a fixed relationship should exist between classes or grades. An argument in favor of geometrically related size grades lies in the fact that most particulate mixtures contain such a wide range of sizes that use of an arithmetic diameter scale is practically impossible. Udden, who recognized this fact in 1898,&apos; proposed one of the first grade scales based on a regular geometrical interval. Udden used 1 mm as his basic diameter and a ratio of 2 (or 1/2) between classes. In 1922 Wentworth2 re-examined Udden&apos;s grade scale, retaining the same class interval and basic diameter, but extending the scale in both directions and renaming the classes. In 1930 (Ref. 3, p. 82) the American Society of Testing Materials proposed what is now known as the U.S. Standard fine sieve series, also based on the 1 mm diam, with a v2 ratio between sieves. This, then, is a one fourth Udden-Wentworth series in the sizes below the 4 mesh sieve. The U.S. Standard coarse sieve departs from the 1 mm base and uses inches; hence it is not a direct continuation of the fine series. The U.S. Standard series would thus seem to possess all the attributes of a good grade scale, which it is. It has a large number of classes (sieves). in fact too many for practical use in its entirety. This v2 subdivision of the Wentworth grades has led to the common use of two v2 sieve series, the half-Wentworth and the engineers&apos; series. Geologists and sedimentologists favor the half Wentworth, or 18, 25, 35, 45 sieves, etc., whereas the engineers, preferring round numbers, utilize the other half of the U.S. Standard grade scale in the 16, 20, 30, 40 sieves, etc. The fixed geometrical ratio between classes is an advantage in statistical analysis, but the unequal classes cause some complications in calculations. This is especially true when moment measures are used. It was to simplify these calculations that Krumbein in 1934 devised the phi scale. Phi is defined as being equal to —log2 of the diameter in millimeters. Selection of logarithms to the base 2 relate the phi scale directly to the Wentworth grade scale in such a manner that the whole or fractional diameter values 2, 1, 1/2, 1/4 mm, etc., become rational whole numbers, —1, 0,1, 2, etc. Since this is an arithmetic rather than geometric series, calculations are facilitated. When the logarithm is multiplied by —1 the phi values below 1 mm become positive, those coarser than 1 mm negative. Because of its relationship to the Wentworth grade scale (and in turn to the U.S. Standard fine sieve series) it is not necessary to use the transformation equation to calculate the phi value for each individual sieve; this can be done graphically as shown in Fig. 1. It should be noted that this graph may be extended in either direction to include the range of sizes most commonly used by the individual worker. Application to Statistical Analysis Any attempt at systematically relating size analysis data to properties involves a statistical study whether it is recognized as such or not. Since this is true it would seem more logical to use measures and devices related to the general body of statistical theory. Several methods are available for studying particulate mixtures. One of the most commonly employed, and also the most often misused, is the histogram or block diagram. If its limitations are recognized and provided for, the histogram is a very useful tool. According to conventional practice, the bars of equal width are plotted and the values noted in terms of diameters, when in point of fact, log diameter is implied by such notation. Further, the histogram is sensitive to choice of grade scale and size of class interval, either of which may color the result. Grade scales whose classes are not related by fixed intervals are particularly difficult. Another basic weakness of the histogram is that it pictures a continuous distribution as a series of discrete grades.

Jan 1, 1957

By F. L. Wideman

This paper lists resources of sulfur in Wyoming, Colorado, Utah, New Mexico, and Arizons, an area comprising approximately 522,600 square miles, Sources of sulfur occuring within the region are sulfur are, pyrite and pyritic ores, and natural gases and petroleum. Data concerning these sources are presented on a statewide basis. Some of the known deposits of sulfur ore are surficial and of fumerole origin; other deposits have resulted from oxidation of pyrite or sulfide ores of copper, lead, and zinc. The deposits are small and the sulfur is distributed erratically in them. There is a small production from some of the deposits, and the material produced is used as soil conditioner.

Jan 1, 1957

By J. R. Bridge, D. A. Vaughan

The phase diagram of the Zr-H system over the range 0 to 65 atomic pet was determined by high temperature X-ray diffraction methods. Results show a eutectoid between a zirconium and the hydride phase. The eutectoid temperature was established at 560±10°C with a eutectoid composition of 42*3 atomic pet H. The hydride phase of the lowest hydrogen content is stable only above the eutectoid temperature, but is formed and retained in a metastable state during reaction of zirconium with hydrogen at temperatures below 560°C. One hydride phase is indicated that exists over the composition range 55 to 65 atomic pet H. RECENT increase in the industrial importance of zirconium has stimulated several investigations of the reaction of zirconium with hydrogen. Review of the literature on interpretation of absorption isotherms&apos; &apos; shows that attempts were made to relate the observations to the room temperature hydride phases reported by Hagg.3 However, more recently Schwartz and Mallett&apos; reported the existence of a new hydride phase, isomorphous with the lower hydride in the Hf-H system described by Sidhu.4 This phase was found adjacent to the metal in a diffusion gradient sample. In addition to the new phase, Schwartz and Mallett reported on only two of the five hydrides found by Hagg. Gulbransen" confirmed the existence of only three hydrides of

Jan 1, 1957

By R. I. Jaffee, C. M. Craighead, G. A. Lenning

The a-p type alloys are subject to a loss of tensile ductility with increasing hydrogen content. No hydride phase is visible in embrittled a-B type alloys. The embrittlement encountered appeared to be of the strain-aging type. Both compositional and structural factors are shown to influence the hydrogen tolerance of a-B type alloys. IN previous papers by the authors, the effects of hydrogen on the structure and mechanical properties of high-purity and commercial-purity titanium were described. It was shown that the presence of hydrogen in these materials results in a hydride phase having low solubility at room temperature. This insoluble phase had little effect on the room temperature tensile properties, but did decrease the notch-bar toughness to a large degree. The binary Ti-H systemz indicates that hydrogen is much more soluble in £ than in a-titanium. Hence, it is not expected that the embrittling effects of hydrogen in a-fi alloys will be similar to that found in a alloys. Materials of this type studied in the present investigation included two commercial a-/3 alloys, Ti-8Mn and Ti-4A1-4Mn; three high-purity Ti-Mn alloys containing 3, 6, and 9 pct Mn; and four high-purity Ti-Mo alloys, Ti-SMo, Ti-10.9M0, Ti-13.1 M0, and Ti-20M0, of the a-B and B types. Materials and Fabrication—The high-purity base alloys, composed of iodide titanium and high-purity metals, were prepared by double arc melting under argon in a water-cooled copper crucible, using a water-cooled tungsten electrode. Radiographic examination showed homogeneous Ti-Mo alloys. The analyses of the alloys used in this investigation and their as-fabricated hydrogen content, where determined, are listed in Table I. The two commercial alloys were 1/2 and % in. diam bar stock. No analyses other than hydrogen content were made. In order to maintain the a-B relationship existing in the two commercial alloys, vacuum annealing and hydrogenation were carried out in the B field prior to final fabrication. Fabrication then was done by The three high-purity Ti-Mn alloys were forged to 3/4 in. diam rods at 1600°F, and hot swaged to 1/2 in. diam at 1380°F. Machined and degreased bar stock was vacuum annealed or hydrogenated, fabricated to 1/8 in. diam rod by hot swaging, annealed in argon for 1 hr at 1380°F !75O°C), and water quenched. The six yz lb Ti-Mo ingots were forged to Wi in. diam rods at 1600°F and then hot swaged to % in. diam. Machined and degreased specimens were vacuum annealed or hydrogenated in the /3 field, prior to fabrication, by swaging to Y4 in. rod at 1400°F. After fabrication, the 5 and 10.9 pct Mo alloys were annealed in argon for 16 hr at 1290°F and water quenched to give equiaxed a-B structures. The higher molybdenum content alloys were argon annealed 4 hr at 1470°F and water quenched to give all £ structures.

Jan 1, 1957

By E. C. Dominguez, H. B. Scharf

THE Sparrows Point plant of Bethlehem Steel Co., southeast of Baltimore, is the largest Bethlehem plant, with an annual rated capacity of 6.2 million ingot tons. There is considerable diversity of product, but a high percentage is sheet, tin plate, galvanized sheets, and rod and wire. The large amount of light-weight end product requires a number of pickling installations that necessarily consume large quantities of sulfuric acid. In the coking operations sulfuric acid is also consumed in recovery of ammonia as ammonium sulfate and in treatment of recovered light oil derivatives. Total sulfuric acid consumption in the plant is currently approaching 10,000 tons per month, of which 55 to 60 pct is required for pickling. In 1951 the acute sulfur shortage caused grave concern as to future sulfuric acid supply for the Sparrows Point plant. Raw materials for acid making were already at hand in the form of hydrogen sulfide and pyrites sufficient to produce nearly half the sulfuric acid required at that time. It was also known that the Bethlehem mining activities would produce additional pyrites in the future. Late in 1951 Bethlehem management decided to build a 250-ton sulfuric acid plant at Sparrows Point to utilize these raw materials. The plant was built and put in operation in May 1953. The steel plant has expanded considerably since 1951, and it is now necessary to operate the acid plant far over rated capacity in order to supply plant demand. Production of acid in 1954 amounted to 93,000 tons. Raw Materials for Acid Making: Coking operations at Sparrows Point produce a residual fuel gas in large quantity which has a net heating value of 525 to 545 Btu. Prior to 1950, plant surplus coke oven gas was sold to the local utility company. In

Jan 1, 1957

By C. J. Sullivan

Many metalliferous ?provinces are co-extensive with particular groups of sedimentary, volcanic, or :basic plutonic rocks. Deposits may be truly syngenetic (Rand, Rhodesia-Katanga, Mans-field, Blind River, White Pine); re-. concentrated by circulating waters (Colorado Plateau, Red Bed Coppers) ; or re-concentrated thermally during metamorphism and granitization (most uranium and lead-zinc provinces ?and some copper and gold provinces). Basalts may yield important cop-per provinces when folded and re-heated. Granitization of basalts which have not reached the chlorite-carbon-ate phase of metamorphism may produce copper provinces. If they reach ?the chlorite-carbonate stage, granitization may result in a gold province. Copper and copper-nickel provinces may result if gabbros are granitized, and a ?similar alteration of per-idotite may result in asbestos or nickel ores. Many similar associations are known. Granite is not a source of ore, but a result of heat. A classification of ?ore with respect to source rocks is of greater prospecting value than are classifications based on magmatic differentiation and hydrother-mal solution theories. Volcanic centres are important ore foci because the thermally unstable metallic sulphides may be concentrated here by a distillation process. The ores found in the hot spring deposits, viz., mercury, mercury sulphide, sulphur, and the compounds of ?antimony and arsenic, are not those which are soluble in water at low temperature (epithermal sub-division of hydrothermal class), abrut those which are unstable thermally at comparatively low temperatures . Water is one of the most common thermally unstable minerals, and generally accompanies the thermally activated ore-forming sulphides.

Jan 1, 1957

ON FEBRUARY 13, 1953 the Miami Copper Company signed a contract with the United States Government, through the Defense Materials Procurement Agency, whereby it under- took, with a base price of 27.359 per lb (subject to escalation based on wage scales and wholesale-price indices), to exploit a new ore body in its mine in Gila County, Arizona. Recoverable ore was estimated at 23,000,000 tons, averaging about 0.677 per cent copper. Moreover, the proportion of oxidized copper, difficult to recover by flotation concentrating, was so high that an average net recovery of only ten pounds per ton (0.5 per cent) was expected. The company proposed to mine the ore by the underground method known as undercut block-caving. Unfortunately the ore body, as has been true of all Miami&apos;s ore bodies, lay so deeply buried that no possibility existed of adopting opencut mining as has been done in recent years at Miami&apos;s neighbors, Ray and Inspiration. Probably the most distinctive characteristic of Miami&apos;s operations has been the extent to which it has developed and improved methods and equipment for underground mining. True, necessity was a potent stimulant, because its available ores since 1926 have been exceptionally low-grade; so, if the enterprise were to survive, it was necessary to keep costs at the minimum. This fact does not detract, however, in any way from the remarkable achievements of Miami engineers in conducting efficient and low-cost underground mining.

Jan 1, 1957