Search Documents

By C. H. Samans, G. F. Tisinai, J. K. Stanley

The times at which the first detectable amount of a phase forms at temperatures between 900° and 1800°F were determined. Both X-ray diffraction and metallography were used to detect a in highly strained filings; metallography alone to detect it in annealed bulk samples of six different types of stainless steels. The a phase was found to form in accordance with the C-type reaction curve in both austenitic and ferritic alloys. In filings of types 304, 347, and 446, a formed in a few hours, and in types 316, 309, and 310, it formed in a matter of minutes at temperatures corresponding to the knee of the C-curve. Only in the bulk type 309 steel, after 500 hr, and in the bulk type 310 steel, after as short a time as 25 hr at temperature, was n detected; in both instances at approximately the same optimum temperature as in the filings. The annealing temperature affected a phase nucleation only for the filings of type 304 and 347 steels, and for the bulk samples of type 309 and 310 steels. KNOWLEDGE of both the rate of nucleation and the rate of growth of the new phase is required for a complete description of metallurgical rate phenomena. However, data on the time for nucleation alone may frequently be useful in evaluating the tendency of commercial stainlcss steels to form s under various conditions. Very little correlated information of this type is available in the literature. Shortsleeve and Nicholson' indicate that s forms in ferritic 24, 27 and 30 pet Cr steels according to a C-type of reaction curve, and Emmanuel's' data for austenitic type 310 steel also suggest this type of solid state reaction. In addition, significant, though fragmentary, information has been given by Binder, Dulis and Smith,4 Payson and Savage,.; Guarneri, Miller, and Vawter,8 rerichs and Clark,7 Wilder,5 Lismer, Pryce, and Andrews,' Smith, Dulis, and Link,10 Dulis, Smith, and Houston," and Henry, Cordovi, and Fischer." The bearing of these data on this work is covered in the discussion. The purpose of this paper is to present such correlated data on s formation in AISI type 304 (18 pct Cr-8 pet Ni), 347 (18 pet Cr-10 pet Ni-Cb), 316 (18 pet Cr-12 pet Ni-2 pet Mo), 309 (25 pet Cr-12 pet Ni), 310 (25 pet Cr-20 pet Ni), and 446 (27 pet Cr) stainless steels. Materials and Test Methods X-ray diffraction and metallographic methods were used to determine the first appearance of the s phase in cold worked filings and in annealed bulk samples of seven steels, under various combinations of time and temperature. The rate of growth of the s particles was not determined. Commercial heats of six AISI steels and a low carbon laboratory experimental heat containing about 28 pet Cr were studied. Analyses are given in Table I. Because cold work greatly accelerates the nucleation of s particles, the relative rates of s nucleation in mechanically strained samples, i.e., filings through 120 mesh, were determined for direct comparison with those in annealed bulk alloys of the same composition.

Jan 1, 1957

By L. M. Howe, J. Gordon Parr, E. Saarema

THE decreasing solid solubility limit at the titanium-rich end of the Ti-Cu constitutional diagram,' Fig. 1, suggests the possibility that titanium-rich alloys may be age-hardenable. However, results obtained by Holden et al. reproduced in Fig. 2 show that after quenching from 790°C the age-hardening of an alloy containing 1.7 pet Cu is very slight, while a 0.8 pet alloy decreases in hardness, during heat treatment at 400°C. It was believed possible that powder samples of alloys might show different results from the lump samples used by Holden et al., since small particles are often more sensitive to diffusion processes than larger samples. Consequently, a 1.9 pet (by weight) Cu alloy was made by the technique of levitation melting," checked for homogeneity, and filings of 48-65 Tyler screen size were cut from it for aging experiments. The filings were helium-quenched (by a technique described previously)' from 790°C, sealed in vacuo in silica tubes and aged at temperatures of 400°, 450°, and 500°C. Microscopic and X-ray examinations failed to reveal any structural changes during the aging process. This is not too surprising since early stages of precipitation do not usually manifest themselves in ways that are readily detectable by metallographic methods, and the extent of precipitation on overaging a 1.9 pet alloy is very small. However, hardness readings (taken on a Bergs-man micro hardness tester, using a 25 g load applied to a diamond indenter) do show a hardness peak at each aging temperature, Fig. 3. About a dozen readings were taken on each heat treated sample; the highest reading and the lowest reading were ignored and an average taken of the remaining values. In

Jan 1, 1957

By H. W. Paxton, C. C. Busby

IT has been shown previously' that strain aging can markedly improve the tensile properties of low carbon martensites, especially the yield-tensile ratio, without seriously affecting the ductility. In view of interest in high strength steels, an investigation has been made of the effect of strain aging following tension or rolling on the tensile properties of A1S1 4340 in an attempt to obtain a tensile

Jan 1, 1957

By Mary Barrett, Walter Rose

INTRODUCTION The conventional way to program reservoir problems* for solution on the electric analyzer1 is one which concentrates the block units towards the inner radius of the prototype system being represented by the analog model. This is achieved by the device of considering block units of equal value radial resistance, leading to the consequences: (1) the ratio of the external to the internal radius of each block unit is a constant (i.e. r1/ri-l = constant a); (2) the external radius of the nth block unit is equal to the innermost radius of the system times the constant a raised to the nth power: (3) the capacitance of the block units increase by a factor of a2 going out radially from the innermost to the outermost boundaries of the system; (4) given n block units in the radial direction, the capacitance ratio of the outermost to the innermost block unit is a (2n-2); and (5) the vertical resistance of the block units decrease by a factor of a going out radially from the innermost to the outermost boundaries of the system, such that the ratio of the maximum to minimum vertical resistance is also given by the factor a(2n-2) PRESENT PROGRAMMING METHOD While this conventional way of programming problems is quite adequate for routine uses of the electric analyzer, it leads to difficulties in those cases where the inner radius of the prototype system (e.g., the well-bore) is small compared to the external radius (e.g.. the external reservoir boundary). To handle such a case by the conventional method would require either that a large value be selected for the constant a or that a large number n, of radial block units be chosen. In consequence, the capacitance and vertical resistance ratios become impossibly large, as will be evident from the relations given above. In any event, the size of the smallest and largest capacitors will always be limited by the size of commercially available components, and the analyzer itself will determine how many mesh points are available for radial block units. For example, it can be shown that if the maximum capacitance ratio which can be electrically handled is a factor of l04, the maximum external radius of the system which can be considered (assuming an internal wellbore radius of 0.25 ft is: It is thus seen that in direct consequence of having the inner wellbore radius small compared to the external radius, models extending beyond 30 to 40 ft are not possible when the capacitance ratio is limited to l04. (NB. A value of 10-9 farads can perhaps be taken as the minimum electrical capacitance possible if corrections for the capacitance of the lead wires are to be avoided. Values greater than 10-5 farads would require the use of unstable and inaccurate electrolytic capacitors). On the other hand, models extending out to 500 to 5,000 ft may be desired in single-well problems, and hence the need for a revised method of problem programming. * REVISED PROGRAMMING METHOD The revised method of programming is one which attempts to retain the desirable features of the conventional method (viz. concentration of block units towards the inner boundary, simplicity in computation, etc.) without having as a consequence that impossible capacitance and vertical resistance ratios will be required. Other advantages will also be achieved by the revised

Jan 1, 1957

By R. M. Genevray, M. B. Bever, E. J. Suoninen

THE martensitic transformation in the ß-phase of the Cu-Zn system has been the subject of several investigations. The transformation is known to be reversible and to be affected by stress. Its temperature range has been determined as a function of composition. In the investigation reported here, the effect of tensile stresses on the transformation was investigated quantitatively. Some information was also obtained on the thermoelastic behavior of the martensite formed in the first stages of the transformation. Most of the experiments were done with alloy E of an earlier investigation;' this alloy analyzed 60.49 pct Cu and 39.51 pet Zn by weight. The methods of shaping and heat treatment were also essentially the same as those previously used. The stress was applied to the specimen immersed in a cooling liquid. The transformation was followed by measuring the electrical resistance with a Kelvin bridge and the elongation with a cathetometer. Fig. 1 shows the M, temperature as a function of stress. Resistance and strain measurements gave essentially identical values. The results suggest a roughly linear relation between M. and in the range investigated, up to 12 kg s mm". At higher stresses, plastic deformation begins to interfere seriously with this relationship. The increase of M, with stress is consistent with published work on the effect of stress on the martensitic transformation. The slope of the curve, 4°C per kg mm ", is of the same order of magnitude as the corresponding value calculated for steel.' Fig. 1 also shows the difference, AM, between the temperature of 50 pct transformation on cooling, as measured by changes in length, and that of 50 pct reverse transformation on heating. This difference, which may be considered a measure of the hysteresis, increases with stress; the decrease at highest stresses is probably associated with plastic deformation. Preliminary work using only resistance measurements was done with an alloy containing 60.15 pct Cu and 39.79 pct Zn by weight. The results indicated higher values o-F M, in agreement with the known variation of M. with composition.' The effect of stress on M, (2°C per kg mm-') was of the same order of magnitude as that shown in Fig. 1 for composition E. An increase in hysteresis with stress was also found. The following experiment was made in order to investigate a partially transformed structure. A specimen of alloy E was cooled to — 85°C under a stress of 4.7 kg mm-'. Under these conditions, the martensitic transformation started but did not go to completion. The stress was then released and the specimen cooled to — 105°C. Fig. 2 shows the measured elongation c. The first change in the slope of the curve indicates the beginning of the transformation under stress. Removing the load at —85°C caused a decrease in length to the value corresponding to the elastic elongation of the parent phase resulting from the applied stress. Hence, the marten-site formed in the first part of the experiment apparently disappears completely and without hysteresis upon the release of the stress. The increase in length on further cooling indicates renewed formation of martensite. These conclusions are consistent with the concept of "thermoelastic" martensite," which has been confirmed by test." Acknowledgments The authors are greatly indebted to Professor M. Cohen for his advice and encouragement. They also thank F. Paxton for assistance. Thanks are due the American Brass Co. which supplied the alloys. References E. Kaminsky and G. V. Kurdjumov: Zhur. Tekhn. Fiziki SSSR (1936) 6, p. 984. A. B. Greninger and V. G. Mooradian: Trans. AIME (1938) 128, p. 337. "J. E. Reynolds, Jr. and M. B. Bever: Trans. AIME (1952) 194, p. 1065; Journal of Metals (October 1952). 'A. L. Titchener and M. B. Bever: Trai~s. AIME (1954) 200, p. 303; Journal of Metals (February 1954). " 3. A. Kulin, M. Cohen, and B. L. Averbach: Trans. AIME (1952) 194. p. 661; Journal of Metals (June 1952). "J. K. Pate1 and M. Cohen: Acta Metallurgica (1953) 1, p. 531. 'C. Crussard: Comptes Rendus (1953) 237, p. 1709. ' G. V. Kurdjumov: Zhur. Tekhn. Fiziki SSSR (1948) 18, p. 999. G. V. Kurdjumov and L. G. Khandros: Dokl Akad. Nouk. SSSR (1949) 66. p. 211.

Jan 1, 1957

By J. W. Miller

An investigation was begun by the Bureau of Mines in 1948 to determine the preparation characteristics of American coals. Results of the investigation were planned to be reported on a county basis and from the data developed to determine: 1. Which coals either as mined or after beneficiation by conventional preparation are chemically suitable under present standards for producing metallurgical coke. 2. Which coals require special and more intensive treatment in preparation than is now practiced. 3. Which coals cannot be considered potential sources of metallurgical coke, regardless of preparation by present-day methods. This report is one in this county series that describes the preparation characteristics of the coals of Lee County, Va.

Jan 1, 1957

The Aberfoyle Tin Mine lies on a wide sloping bench about 2,000-2,500 ft. above sea level, at Rossarden, 14 miles north of Avoca, in north-eastern Tasmania. The quartz-cassiterite veins were discovered in 1916, but mining did not begin until 1926. Trenching revealed seven small tin-bearing veins within a width of 57 ft. of Palaeozoic slates and sandstones, and it was assumed that the mineralization extended beneath the adjacent cover of Permian strata, but the presence of the main vein system (the 26 Vein System) was not suspected until the Aberfoyle Fault was discovered late in 1928.The mine has now been developed on thirteen levels, to a depth of 1,350 ft. The lower limit of economic mineralization appears to lie at about the ll-level, which is 1,060 ft. vertically below the concealed outcrop of the main veins. Production of tin and tungsten concentrates began in 1932, and to date more than 550,000 tons of ore have been mined for a recovery of 8,856 tons of tin concentrates, and 3,056 tons of wolfram concentrates, valued at approximately £6,500,000.This paper reports part of an investigation undertaken by the Mineragraphic Investigations Section of C.S.I.R.O. to study the mineral composition of the ore in relation to the apparent failure of cassiterite and wolfram mineralization to extend below the present working limits of the mine, and was first issued as Mineragrapnic Report No. 639.GENERAL GEOLOGY:The deposit consists of a series of quartz veins in a northsouth trending sheeted zone, transecting folded slates and...

Jan 1, 1957

By Nicholas J. Grant, Ernest P. Abrahamson

IN recent work, Bloom and Grant' and Stein and IGrant' have indicated that a high temperature chromium phase exists. In the 68 pct Cr-Ni binary they found a eutectoid reaction, P chromium transforming to a chromium plus y nickel at 1215°C. Un-

Jan 1, 1957

By K. E. Stanfield

The Bureau of Mines oil-shale program, initiated in April 1944, is concerned with the future utilization of oil shale in the United States as a source of liquid fuel. One phase of this program is the accumulation of information on the location, extent, and richness of oil-shale deposits that may be suitable for processing to oil and related products. A previous publication5/ presented, by means of logs, the oil yields of sections of the largest known oil-shale deposit in this country -the shales of the Green River formation occurring in adjoining portions of the states of Colorado, Utah, and Wyoming. This present supplementary report presents the oil yields of cores from 48 holes drilled during 1952 to 1954 in the Green River formation of Colorado, which is distributed over an area of more than 1,000 square miles. The oil yields of the 48 oil-shale sections, involving the assay of 9,651 samples, representing 22,451 feet of core, are presented by means of logs. In addition, the oil yields of samples comprising the maximum sections of 15 gallon-per-ton shale are tabulated for these cores and for the 28 cores from Colorado which were logged in the previous report.

Jan 1, 1957

By James Westfield

A brief resume follows of some recent activities of the Division of Coal-Mine Inspection that have had a favorable effect on health, safety, and the reduction of injuries at coal mines: 1. The Federal Mine Safety Code for Bituminous-Coal and Lignite Mines of the United States was issued originally by the Director of the Bureau of Mines on July 24, 1946, after consultation with management and labor representatives of the coal-mining industry. The code has been used by Federal coal-mine inspectors during their inspections of bituminous-coal and lignite mines as a basis for determining the existence of unhealthful and unsafe conditions and practices in these mines. A revised code was issued by the Secretary of the Interior October 8, 1953, following further consultations with representatives of management and mine workers, and was incorporated by reference in the 1952 and subsequent bituminous-coal wage agreements. The agreement of May 29, 1946, between the Secretary of the Interior, acting as Coal Mines Administrator under authority of Executive Order 9728, and the United Mine Workers of America, covering bituminous-coal and lignite mines in Government possession, charged Federal coal-mine inspectors with the responsibility of making periodic investigations of the mines and reporting to the Coal Mines Administrator any violations of the Federal Mine Safety Code. The inspectors were active in making prompt investigations of hazardous mines that had been closed by order of the Coal Mines Administrator to determine if enough improvements had been made to allow the mines to reopen. Federal coal-mine inspectors also had temporary authority to close mines they found to be imminently dangerous, but such authority (under Executive Order 9728) was removed on June 30, 1947, when Government control of the mines was terminated.

Jan 1, 1957

The first metal-mine accident-prevention course was prepared and published in 1942-45 as a series of seven miners' circulars (Nos. 51-57). The scope of the course has been broadened, revised, and brought up to date, and it is being published as a similar series of seven miners' circulars on accident prevention in metal and nonmetallic mines. These circulars are: 1. Accident Statistics (Miners' Circular 51), dealing with general statistics on accidents and injuries at metal and nonmetallic mines, including causes, costs, and the uses of investigations and reports of all accidents.

Jan 1, 1957

The first metal-mine accident-prevention course was prepared and published in 1942-45 as a series of seven miners' Circular (Nos. 51-57). The scope of the course has been broadened, revised, and brought up to date and is being published as a similar series of seven miners' circular pros. 51-57, revised) on accident prevention in metal and nonmetallic mines. These circulars are: Accident Statistics (Miners' Circular 51), dealing with general statistics on accidents and injuries at metal and nonmetallic mines, including causes, costs, and the uses of investigations and reports of all accidents.

Jan 1, 1957

By E. P. Carman

This report is the 20th in a series summarizing Bureau of Mines research and technologic work on coal and related investigations; it is the second4/ to be issued on a calendar-year basis. Previous reports related largely to publications by Bureau authors during the reporting period. This one discusses the publications issued during 1955 and in addition describes briefly the work in progress during the year. Further details on the published work may be found by referring to the publications cited in the footnotes. The Bureau continues to direct its research and technologic work on coal toward safer and more efficient mining, improved preparation, and more effective utilization, with the ultimate twin goals of promoting conservation and insuring that coal will make its maximum contribution to the Nation's industrial capacity. Significant advances toward these goals were made in 1955.

Jan 1, 1957

By T. A. Klinefelter

ONE OF THE many services rendered by the Federal Bureau of Mines is the identification and general examination of ore and mineral samples. Many of these, coming from almost every State in the Union, are clay and shale samples. Other Government agencies, State geologists, universities, and other laboratories are often requested to make similar examinations. This publication describes methods of testing these samples. An earlier paper, published in 1943, described Bureau of Mines methods of testing such clays.3 This paper was to be followed later with another (part II) that would describe much more thorough testing than did the rather general outline of part I. Part I has been out of print for some time and needs revision, and part II was never written; hence, the present publication is designed to include part I and also those additions intended as part II. The tests presented in part I were simple, requiring only the ordinary equipment to be found in any good chemical laboratory. The second publication was to include a greater number of test procedures and information on increasing the accuracy and precision of those previously given.

Jan 1, 1957

By R. B. Bauder

In connection with a Bureau of Mines research program on utilization of Cuban lateritic ores, a comprehensive review was made of the chemical literature on nickel and cobalt. Initially, the review had as its objective the selection, from the voluminous literature dealing with the chemistry of these two metals, of only those references to reactions that were especially pertinent, or at least closely related, to the field of extractive metallurgy. Later, the coverage was extended to include references to the techniques and plant applications of extractive metallurgical procedures for the recovery of nickel and cobalt. In this report, the period from January 1929 to July 1955 has been covered, as it seemed logical that recent literature should be of greatest value. This cutoff date was established in order that the bibiliography could be issued at an early date, inasmuch as currently much work is in progress on the lateritic ores. Later, a supplement will be prepared extending the coverage to about 1900.

Jan 1, 1957

By James L. Elder

Field-scale experiments were conducted at Gorgas, Ala., from 1951 to 1954. Three reaction paths were formed by electrolinking-carbonization, using electrode spacings of 150, 152, and 155 feet. The coal along these reaction paths was gasified, using air, oxygen, and steam separately or in various combinations. At the conclusion of operation, a drilling survey was conducted to determine the location and approximate area of the reaction zones. During the applications of the electrolinking-carbonization technique the maximum limitation on electrode spacing was not determined. Initial tests were conducted at 60-foot spacing. Successful path-preparation tests were made at 150-, 152-, and 155-foot spacings, and the indications were that much longer spacings were possible. The potential requirements appear to be constant, regardless of path length, while the gross power required probably will increase with path length. During the carbonization phase gas was produced that is similar in quality to coke-oven gas produced at low to intermediate temperatures.

Jan 1, 1957

By Scott W. Hazen

METHODS of determining the grade and tonnage in a mineral deposit have not kept pace with scientific developments in certain other fields. The most commonly used methods of computing ore reserves and grade based on diamond-core-drill sampling are the cross section, the polygon, and the triangle. Tonnage and grade may be determined by these methods with acceptable accuracy, providing a sufficient number of samples is obtained; however, there is no means of determining when an adequate number has been taken or conversely if the deposit has been sampled excessively. It is demonstrated that, by using the techniques of statistical analysis, a mining engineer will be able to determine when a sufficient number of samples has been taken to determine the grade of a mineral deposit within a specified degree of confidence. Using statistical analysis to compute the estimated average grade of the ore makes it possible to compute a fiducial interval, when a distribution of the sample means is normally distributed, so that there is 95-percent confidence in the statement that the true average grade of the deposit is covered by the interval. This report utilizes data obtained from the Maggie Canyon manganese deposit, Artillery Mountains region, Mohave County, Ariz. Four separate exploration projects were conducted at Maggie Canyon between 1936 and 1950. Present economic conditions have made it desirable to determine the amount of 5-percent manganese ore developed by these projects.

Jan 1, 1957

By Ruth F. Brinkley

This report is the 16th of a series of reports originally issued annually and more recently biennially to acquaint the reader with the work of the Explosives and Physical Sciences Division, Region VIII.3/ In the majority of instances the results of the investigations are made available to the public through Government publications and journal articles. In certain instances (specifically as regards security-classified research, investigations of a confidential nature, and short-range programs of very limited scope) results are reported only to those immediately concerned.

Jan 1, 1957

By Wilmer McInnis

MOLYBDENUM, one of the more versatile alloying elements in modern metallurgy, was first isolated by Hjelm in 1782. The pure metal is silvery white and softer than steel. It melts at a higher temperature than all other metals except rhenium, tungsten, and tantalum. Molybdenum, a member of group V of the periodic table, chemically exhibits valences in stable compounds of 2, 3, 4, 5, and 6. It is a strong carbide-forming element, and much of its alloying effect in steel is imparted through the formation of carbides. Molybdenum occurs in nature only in combination with other elements. The most common occurence is molybdenite (MoS2), which is widely distributed throughout the world; the few known commercial deposits are the major sources of molybdenun1. The other commercially important mineral, wulfenite (PbMo04), was a major source of molybdenum in the United States during the early part of the 20th century, but with exploration and development of the world-famous Climax molybdenite deposit during the World War of 1914-18, molybdenite soon became the world's major source of molybdenum. In recent years, virtually no wulfenite has been mined. Many copper deposits contain minute percentages of molybdenite; and, since the inauguration during the early 1930's of the recovery of molybdenite as a byproduct of these deposits, they have been an important source of molybdenum.

Jan 1, 1957

Jan 1, 1957