Search Documents

By Donald Ingvoldstad, Harold E. Lee

AT Bunker Hill the original charge storage and preparation system was installed in 1917 to accommodate lead-silver gravity mill products. Only minor tonnages of wet fines such as vanner and flotation concentrates were received. Charge flux and diluent requirements were .provided by an ample supply of siderite middlings and coarse lime-rock. While oversize material was crushed through ¼in., the use of roll crushers in series resulted in a more or less granular, free-running charge of adequate porosity. Under such conditions, receipts could be proportioned directly from receiving bins, and suitable blending was obtained by passing the resultant layered composite through a small Stedman disintegrator. This elementary system served well for production and smelting of an extremely lead-rich sinter, in the low column blast furnace. Here sinter physical quality is less critical, and appreciable quantities of raw flux and oxidized ore may be charged directly to the blast furnace without seriously impairing furnace capacity. Prior to 1938 the relative proportions of zinc receipts were low and extraneous flux requirements at a minimum. However, subsequent war-inflated zinc demands brought marked increase in fine concentrate and slimy zinc leach residue receipts and an abrupt introduction to smelting a more refractory zinciferous charge. The higher temperature demands of the more refractory zinciferous charge required a higher smelting column and the higher column, in turn, rendered the blast furnace less receptive to improperly prepared feed. Inadequate presinter processing facilities prevented the production of acceptable sinter, and blast furnace production declined to 50 pct of former capacity. In view of a prevailing contention among lead metallurgists as to the deleterious action of high zinc slag on blast furnace capacity, it was natural to overstress this factor and to concentrate on possible changes in furnace design. Another interpretation was that primary correction should be sought through expanded sintering facilities. This divergence of opinion, together with the extreme material shortages of the 1940's, delayed corrective

Jan 1, 1957

By B. C. Mariacher

EXTRACTION of uranium from ores is being ac-complished by processes which. for the most part, subject the entire ore to acid or carbonate leaching. Ore deposits with a U 3 O 8 content below 0.10 pct U 3 O 8 are seldom considered suitable for treatment by leaching. A preliminary concentration that would enrich the uranium content of an ore by a simple, low cost process based on physical properties of the ore might result in some low grade deposits becoming commercial ores. In addition, the process might be employed in existing operations to reduce transportation and leaching costs and to increase capacity of existing leaching plants. A study to attempt the development of a preliminary concentration process for primary uranium ores was undertaken by the Colorado School of Mines Research Foundation under sponsorship of the U.S. Atomic Energy Commission. The objective of this work was to produce concentrates containing 0.25 pct U3O8 from the low grade ores tested. Ores Tested: The main effort was devoted to the low grade primary uranium ores from northwestern Saskatchewan. Samples were obtained from the Beaverlodge operation of the Eldorado Mining & Refining Ltd. Additional primary ores, obtained from deposits in Gilpin County, Colo., contained from 0.07 to 0.10 pct U3O8. Summary of Concentration Tests: The Beaverlodge ore was tested to determine amenability of the ore to concentration by magnetic, electrostatic, gravity, and scrubbing processes. None of these produced satisfactory results. Both gravity and magnetic processes produced fairly good concentrates when closely sized fractions of the ore were treated, but on the basis of treating the total ore, recovery was poor. Preparation of sized fractions and the low capacity of equipment for suitable concentration made these methods impractical. As flotation offered the advantage of treating the total ore without intermediate sizing, the main effort was in this direction. A flotation process was developed that fulfilled the concentration objectives as set by the AEC. Pilot plant testing was used to verify results obtained from laboratory batch testing. Mineralogy: A petrographic examination of the Beaverlodge ore included a study of polished sur- faces and identification of the radioactive mineral by autoradiograph and X-ray diffraction. Approximate quantitative mineral identification was as follows: quartz, 60 pct; orthoclase feldspar, 20 pct; chlorite, 10 pct; carbonates, 5 pct; and miscellaneous minerals, 5 pct. Included in this last group were plagioclase feldspar, pyrite, mica, chalcopyrite, pyroxene, sericite, magnetite, galena, and uraninite. The most general occurrence of uraninite was in the form of crusts and thin coatings on limonite-stained grains of pyrite, quartz, and pyrite-quartz intergrowth. At least 90 pct of the uraninite was still attached to other minerals in a 100 by 200-mesh size fraction. The uraninite crusts were as small as 10 to 20 µ diam, and 5 to 10 µ thick. The Flotation Process Petrographic examinations of the Beaverlodge ore had indicated the impracticability of attempting to concentrate the uranium by floating individual grains of uraninite. Liberation of the uraninite required grinding to sizes below those suitable for flotation. However, there was preferential association of the uraninite with some minerals while others were free of uraninite attachment. The approach to the development of a flotation process was, therefore, based upon an attempt to concentrate the uraninite by floating carrier minerals. The following paragraphs discuss the various stages of the process with regard to the factors tested and the conditions under which best results were obtained. Grinding: The most effective size range for flotation was —150 mesh + 13 µ. The —13 µ material in the final concentrate had a higher U3O8 content than the total ore, but not as high as the average concentrate; however, rejection of slimes before flotation was prohibitive because of the loss in uranium carried in the —13 µ fraction. Grinding techniques which contributed to a minimum production of fines, such as stage grinding, were then employed. Quartz and Silicate Depression: These minerals represented approximately 80 pct of the ore and were free to a large degree of uraninite attachment. Significant improvement in the grade of the concentrate was obtained by depression of these minerals with hydrofluoric acid or sodium fluoride. Promoter: Selective stage flotation of uraninite carrier minerals was simplified by development of a single promoter mixture. The mixture consisted of an emulsion of a fatty acid, fuel oil, and a petroleum sulfonate and was selected after a comprehensive series of tests. It contained three parts by weight of an oleic and linoleic acid such as Emersol 300,

Jan 1, 1957

By W. R. Opie

The object of this paper is to show the manner in which typical electrodeposits of hexagonal-close-packed metals—zinc, titanium, and zirconium—tend to form. The conditions of electrodeposi-tion markedly affect the nature of the deposits in regard to crystal size, orientation, and appearance. No attempt is made to correlate cell conditions with deposit quality but, rather, characteristic types of deposits were selected and a study made to show the relationship between outward appearance and crystal structure. The zinc deposits were made in aqueous electrolytes and the titanium and zirconium deposited from fused salt baths. ZINC deposits studied were made in the American Smelting and Refining Co.'s Central Research Laboratories. They were representative of bright, shiny, smooth deposits, which can be obtained by using proper current densities and electrolyte addition agents, and of deposits which are dull and tend to be nodular. Four deposits were selected which ranged from smooth and bright to very nodular and dull, and their classifications are shown in Table I. These were examined microscopically and were found to differ quite markedly in outward surface structure and in microstructure. The outward surface variation is illustrated in Figs. 1 to 4. At X50 the texture could be seen to progress from granular to platelike to smooth. The microstructures of the deposits' cross sections from starting sheet to outer surface are shown in Figs. 5 through 8. The dull nodular deposits (sample Nos. 1 and 2) show some tendency for acicular growth. The platelike sample (No. 3) shows tendency for columnar growth development and the smooth deposit (No. 4) has a well developed columnar structure. Back-reflection X-ray patterns of the deposit surfaces revealed some interesting information. The crystal orientation was random in all deposits except the smooth deposit. Fig. 9 is a typical back-reflection pattern of a nodular deposit. All planes are reflecting in the proper relative intensity. The pattern of the smooth deposit is shown in Fig. 10. The only planes which reflect are the (10.4). This series of planes is in the right position, with the FeKa radiation used, to satisfy the Bragg equation if the basal planes {00.1) are at right angles to the X-ray beam. The results were interpreted to mean that in the bright smooth deposit preferred orientation has occurred with the basal hexagonal planes oriented in the plane of the sheet but with all other planes randomly oriented around the c-axis.

Jan 1, 1957

By E. J. Roberts, E. B. Fitch

THE mechanism of classification by settling pools is most simply shown in the case of batch sedimentation such as was analyzed by Oden.1 The batch model will be considered, therefore, and it will be shown that the same mechanism applies to continuous operation. Classification in Batch Settling Pools: Consider a beaker or tank of slurry containing particles so dispersed that they can settle independently of one another under the influence of gravity. Originally all particle sizes are uniformly distributed throughout the suspension. All particles start immediately to settle towards the bottom at rates determined by their size, shape, and density—among other factors. Particles reaching the bottom settle out of suspension. After some given time the slurry above the deposited solids is siphoned off or otherwise removed, leaving the deposited solids behind. The deposited solids, together with entrained and any unremoved supernatant slurry, represent the underflow of a classifier. The slurry removed represents the overflow. There is a certain separation, size of particle which during the sedimentation has just time to settle from the top surface of the slurry to the level at which underflow and overflow are parted. All particles with a faster settling rate will have dropped to below this level, no matter where in the beaker they started from originally, and therefore will be absent from the overflow. Particles with a slower settling rate will not reach this level if they started from the top of the slurry, but a portion of them,

Jan 1, 1957

By A. J. Griest, J. C. Danko

IN the course of vacuum evaporation experiments, sublimation figures were observed on the surface of a pure nickel specimen. A cubic figure, typical of those observed on this specimen, is illustrated

Jan 1, 1957

By Gordon G. Bentle, W. P. Fishel

GREINER, Marsh, and Stoughton1 have reviewed the literature in a monograph on the iron-silicon system. The lack of agreement among the various studies may be due to the difference in the purity of materials in some cases. The results of the X-ray method indicate only a general rather than a specific limit of the y loop. The iron-titanium system was investigated by Roe and Fishel,' whose results are used in determining the iron-silicon-titanium y loop. The literature indicates that no study has been made thus far of the iron-silicon-titanium system in the y loop region. Experimental Procedure The alloys were made from Armco iron, 99.86 pct Si, and 98.5 pct Ti. The titanium contains 1.07 pct Fe. The Armco iron contains 0.01 pct C, 0.005 pct Si, 0.02 pct Mn, 0.006 pct P, 0.01 pct S, and 0.04 pct Cu. A dilatation sample of Armco iron was prepared in the same manner as were the other samples. Several dilatation runs indicated that Ac3 begins at 905°C and ends at 910°C, which compares favorably with the study of Wells, Ackley, and Mehl' employing specially purified iron. All alloys were melted in an induction furnace in Alundum crucibles and were top poured into baked core sand molds. The ingots weighed about 600 g as cast. Dilatation samples of 4 in. by % in. diam were taken from the bottom end of the ingot, from which turnings for analysis were taken. Turnings from each end of two of the samples indicated that the alloys possessed uniform silicon content. A hole was drilled halfway through each end of a 4 in, dilatation sample. A chromel-alumel thermocouple was inserted in each hole and the surrounding metal peened in to hold the thermocouple in place. Fig. 1 represents the dilatation apparatus. The heating unit is an Alundum tube wound with resistance wire; the dilatation tube is a McDanel combustion tube; the push rod is zircon; the dial gage is graduated in 0.0001 in. and was vibrated to prevent sticking. A blank run over the temperature range of interest gave no significant dilatation. The thermocouples were attached to a multiple recording micromax which indicated the temperature at each end of the sample at 35 sec intervals. A Lindberg control unit governed the rate of heating of the furnace, and lowering or raising the

Jan 1, 1957

By F. H. Deily, L. W. Ledgerwood, J. E. Eckel

A new method for drilling the earth's formations has undergone extensive laboratory and shallow earth drilling experimentation. This method, pellet impact drilling, uses the energy of a large mass of high velocity steel spheres to break and crush the rock. Pellets are confined to a region close to the hole bottom. Motive fluid for transporting and recycling the pellets is supplied by a modified jet pump. The pellet drilling method has inherent advantages over conventional rotary drilling. First, only a nominal amount of weight need be applied to the hole bottom. Second, only a very small amount of torque is required for bit rotation. Third, means are available for continual replacement of the cutter medium. The experimental laboratory work and analytical procedures necessary for the design of a pellet drill bit are described. In the laboratory program approximately half the effort was devoted to the development of a better understanding of the physical process, and half to the empirical testing of new bit configurations. Factors such as pellet size and velocity, jet pump characteristics and modifications, and power distribution are discussed. The design and construction of a pellet impact bit for drilling a 9 in. hole with 1 1/4 in. steel pellets are described. Drilling performance in representative rocks, hydraulic operating characteristics, and metallurgical problems are discussed. INTRODUCTION This paper discusses an attempt to reduce drilling costs through the development of a drilling method basically different from rotary drilling. Publications on drilling research indicate that the major effort on the part of manufacturers and operators has been confined to research in rotary, or rotary-percussion drilling. This applied drilling research has produced significant gains in drilling rates and bit life, but thus far it has failed to achieve any major decrease in general drilling costs. From recent statistics released by Drilling Contractors, it can be shown that the total cost of drilling an "average" well in 1953 was about 2 1/4 times the corresponding cost in 1935. Analysis of the costs will show that they are not due to inefficient field operations; they are due instead to both an inflated economy and greater "average" well depths. Diligent work by the industry has reduced the backlog of potential economic improvements in rotary drilling to a group of rather marginal prospects. Increasing depths and poorer quality reservoirs at these depths continue to make the drilling cost problem more acute. Hence, the aim of the work reported here was to develop a new drilling method not limited by the inherent characteristics of rotary drilling and thus capable of attaining further significant reductions in drilling costs. The effort devoted to research on this proposed new drilling method was of considerable magnitude and represented .in excess of 37 man-years of research. The affiliates of Standard Oil Co. (N. I.) sponsored this development program which was conducted by the Drilling Methods Section of the Carter Research Laboratory in Tulsa, Okla. The purpose of this paper is to

Jan 1, 1957

In considering the architectural design of the group of buildings which make the surface workings of a mine, the variety of function of the buildings is the most outstanding feature. It falls to the architect to unify the group in a manner which still expresses the function of the individual buildings. In achieving this, many perspective studies were made at an early stage and as the area was developed, a scale model was produced initially for design study purposes and later completed as a model of the final development.

Jan 1, 1957

MR. J. F. MYERS, Consulting J3eneficiation Engineer, Greenwich, Conn.: In the written discussion contributed by Mr. F. C. Bond in item ( 2) (page 515), speaiking about the significance of the ratio of mill diameter to the make-up ball diameter, he states: "When this ratio exceeds 100 the power and capacity of the mill are de-creased"; and the paragraph ends with a reference to the 30 per cent ball volume "with some de-crease in mill capacity". I believe this broad statement is incorrect. When we are dealing with a non-cataracting mill, pre-ceded by a good rod mill, there is a slight increase in capacity, but the power does drop. The second point that I consider needs consideration is Mr. Bond's item (8), Proper Mill Speed (page 516). This paragraph should be qualified to cover single-stage mills only. It does not apply where a rod mill is followed by a non-cataracting ball mill. The statement as is, with no qualification, gives an erroneous idea of proper mill speeds.

Jan 1, 1957

By R. F. Domagala, M. Hansen, D. J. McPherson

Iodide zirconium was combined with calculated amounts of nitrided zirconium sponge and arc melted to prepare alloys in the 0 to 6 wt pct N region. Annealing treatments were carried out at 21 temperature levels. Metallographic examination of the heat-treated specimens permitted construction of the binary phase diagram from 0 to 6 pct N. Features of the diagram include the peritectic formation of both a and ß solid solutions. The maximum solubility of nitrogen is 0.8 pct in 8 zirconium and 4.8 pct in a zirconium. An X-ray study of nitrided materials was made in the range 6 to 13 wt pct N region because serious nitrogen losses were experienced when attempts were made to arc melt these high nitrogen alloys. PHASE relationships in the Zr-N system have been determined. Due to the inability to retain nitrogen in nitrogen-rich alloys subjected to arc melting, definitive work was possible only in the range 0 to 6 wt pct (0 to 30 atomic pct) N. Sufficient complementary X-ray work was done to permit construction of the binary phase diagram up to 13.3 wt pct (50 atomic pct) N (ZrN). Small ingots were prepared by arc melting master alloys with enough zirconium to produce an alloy of the desired composition. Following pretreatment, alloys were annealed at temperature levels between 600" and 2020°C. Determination of the phase boundaries was then accomplished by metallographic evaluation of specimens quenched from the various temperatures. Incipient melting techniques were used to corroborate solidus curves, and X-ray diffraction was employed to study the nitrogen-rich region of the a + ZrN phase field. Materials Westinghouse Grade 1 iodide zirconium crystal bar served as the base material for this investigation. The as-received bars were lightly sandblasted, pickled in a 20 pct HN0-5 pct HF aqueous solution, rinsed in water and acetone, and dried. They were rolled to about 1/32 in. strip and acid-pickled, followed by water and then acetone rinses. The material was sheared to approximately 1/4 in. squares, cleaned with acetone, and stored for use. Pure zirconium nitride is not commercially available, according to correspondence with possible suppliers. A literature survey indicated that nitrogen may be introduced into zirconium metal by passing nitrogen or ammonia gas over zirconium at an elevated temperature. After considerable experimentation, a train was devised whereby high quality nitrogen was passed through a series of bubblers to remove the last traces of oxygen, through an H,SO, bubbler and a cold trap to remove moisture, and finally over zirconium within a resistance furnace. Hand-picked Bureau of Mines magnesium-reduced zirconium sponge proved more amenable to nitriding than the crystal bar. The nitrogen used was extra pure gas purchased from Linde Air Products Co. The first two bubblers through which the gas was passed contained a solution suggested by L. F. Fieser" as being ideal for removing the last traces of oxygen from nitrogen. The solution contains 20 g KOH, 2 g sodium-anthraquinone ,9-sulphonate, and 15 g NaHSO, dissolved in 100 ml water. It is blood-red and turns brown when contaminated with oxygen. A saturated lead acetate solution, next in the series of bubblers, removed any H2S which might have formed in the 0, removal stage. An H,SO, bubbler and cold trap removed moisture before the nitrogen was passed over the zirconium. The zirconium was contained in a stainless steel screen within a Vycor or quartz tube in a resistance furnace. Unreacted nitrogen passed out of the system through a mercury bubbler. A nitriding run was performed in the following manner: Zirconium was placed in the screen within the furnace tube. The unit was assembled, suitably clamped off, and evacuated to remove the air and moisture within the tube and that trapped by the zirconium sponge. The unit was flushed with nitrogen and evacuated twice. After nitrogen was allowed to pass over the zirconium for about 30 min, the furnace was turned on; several hours were required to reach temperature. The reaction was allowed to continue at temperature for about 4 hr and the screen was then withdrawn from the hot zone of the furnace by means of a Nichrome or Kanthal rod. The screen and its contents were allowed to cool at the end of the tube and were then removed. At 800°C no more than about 5 pct N could be introduced into the sponge zirconium. This material was designated M-1 (master alloy No. 1) and reserved for the preparation of alloys in the dilute nitrogen region. A second set of experiments was conducted at 1000°C; no more than 7.2 pct N could be introduced into the zirconium at this temperature. Enough material (M-2) of this nitrogen content was prepared to produce a second set of alloys to complement the first and to provide alloys in the 0 to 6 wt pct N range. It was hoped that a diffusion anneal plus a re-nitriding might yield a material of higher nitrogen content. The material containing about 7 pct N was therefore given a homogenization treatment at 1000°C for 6 hr under an argon atmosphere. It was

Jan 1, 1957

By W. L. Dare

This publication is one of a series by the Federal Bureau of Minus describing methods and costs of minim, uranium on the Colorado Plateau. The La Sal mine is in the Big Indian mining district, about 29 miles southeast of Moab, San Juan County, Utah. The claims that encompass the mine were located in March 1953, and the La Sal ore body was discovered as a result of a drilling program begun in August 1953. The mine is owned by the La Sal Mining & Development Co., a subsidiary of the Homestake Mining Co. Homestake continued the drilling program and in May 1954 began sinking a 572-foot shaft and constructing a surface plant. The plant and shaft were completed in October 1954. The La Sal ore body is in the Chinle (Triassic) formation. it is tabular and dips with the enclosing beds about 8° southwest. The ore body is generally 4 to 8 feet thick but in a few places is as much as 20 feet thick it is being developed by a series of strike drifts and dip inclines, driven within the ore stratum on about 100-foot centers. A haulage level driven beneath the ore body is connected by raises to the upper workings.

Jan 1, 1957

By Gordon W. Hodgson, Edward Tipman

INT'RODUCTION An appreciable number of the oil fields in Western Canada are accumulations of heavy black oils in more or less unconsolidated sandstones. When the crude oils are produced by conventional means, they are frequently contaminated with both sand and oilfield water. The water is usually present as emulsified water, and the sand and other solid materials are suspended in the emulsions. The presence of the solid material in the crude oils is troublesome and, in general, little is known about the behavior of suspended solid particles in emulsions. The Stokes equation describes the behavior of suspended particles in homogeneous fluids in terms of particle size, density differential, and fluid viscosity. In the case of an emulsion, particle size and density differential introduce no difficulties, but considerable doubt centers around the viscosity term. It has been reported1 that the viscosity of an emulsion is related to the viscosity of the continuous phase by an expression of the type: n = a, (1 + a C) where n is the viscosity of the emulsion, n,, is the viscosity of the continuous phase, a is a constant, C' is the volume concentration of the disperse phase. The value of 17, the coefficient of the concentration term, has been determined for various systems, and has been found to vary from a value of 1 to 4.75. The value of 2.5 has been found to be applicable to a large number of systems, and this is the value that is widely used in the equation which then becomes the Einstein equation for the viscosity of emuls~ons. It is of considerable significance that neither the particle size nor the viscosity of the disperse phase enters the expression; the expression for the viscosity of the enlulsion is based solely upon the viscosity of the continuous phase and the concentration of the disperse phase. For crude oil emulsions the Simha equation and the data presented by Fukushima and lchimurai show a non-linear dependence of the viscosity ratio on the water concentration. While it is undoubtedly reasonable to use these data for predicting the viscosity of a specific emulsion, and while it is equally reasonable to expect the calculated viscosity to predict the settling rate of a solid spherical particle in the emulsion by means of Stokes equation, there seems to be no direct evidence that this calculation is indeed sound for describing the settling rates of solid particles in emulsions of water in crude oils. PROCEDURE A direct approach to the problem was thus indicated. Laboratory equipment was designed and built for the direct determination of the rate-of-fall characteristics of solid particles in emulsions of water in oil. Although the apparatus incorporated the basic design of conventional falling-ball viscometers, the study was concerned directly with the rate-of-fall characteristics of particles in emulsions, rather than with the viscosity of the emulsions as such. The crude oil used in this study was a very heavy black crude oil—the McMurray oil obtained from oil-soaked sands outcropping on the Athabasca River in northeastern Alberta. It was produced from the sands by strip mining followed by hot-water separation of the oil in the separation plant of the Alberta Government at Bitumount'. The primary plant product was a wet crude oil containing about 5 per cent solids and 35 per cent water. The final plant product was only slightly different from the native oil, having lost only about 4 per cent of its bulk as light ends during dehydration distillations. In the present investigation two kerosene dilutions of the McMurray oil were used in addition to the dry plant product. The McMurray oil contained 1.92 per cent solids. Analysis of the solids by X-ray diffraction showed the presence of kaolinite, pyrite, and illite as major constituents. with lesser amounts of quartz. Particle size of the pyrite and quartz was less than 10

Jan 1, 1957

By J. E. Dorn, L. A. Shepard

LOW and Gensamer' demonstrated a number of years ago that the yield point phenomenon in mild steels was associated with the presence of fer-rite soluble carbon or nitrogen. More recently the yield phenomenon in body-centered-cubic metals containing interstitials was rationalized by Cottrell' in terms of a simple dislocation model. Interstitial atoms interact with dislocations in two ways; they cause not only local expansions but induce local tetragonality in the lattice. Consequently, interstitial~ interact with the hydrostatic tension and shear components of the stress about dislocations. They tend to migrate toward the expanded regions of edge dislocations and to assume sites that relieve the shear stresses of screw dislocations. Thus, a dislocation saturated with solute atoms constitutes a lower free energy state than that obtained when the dislocation threads through the average composition regions of the matrix. A greater stress will be required to separate the dislocation from its atmosphere than to move the dislocation through the matrix. This factor gives rise to the upper yield stress, which is required to unleash a series of dislocations in a localized region. This local yielding is propagated across the specimen to form a thin band of plastically deformed material known as a Lueder's band, making an angle of about 45" to the stress axis. Once the band has formed, deformation continues at the lower yield stress by the spreading of the Lueder's band in the direction of the applied stress. Undoubtedly the spreading of Lueder's bands at the lower yield stress is accomplished by the high stress concentrations at the band fronts, which serve to induce continued unlocking of new dislocations in advance of the migrating band fronts. Cottrell and Bilby have shown that the dependence of the yield point on temperature can be deduced by assuming that thermal fluctuations aid the stress in unlocking small dislocation loops from their solute atmospheres. Once a loop that exceeds a critical size has been nucleated, the entire locked diqlocation is released and can migrate. Fisher4 simplified this analysis by assuming that the locking forces were short range, so that if the dislocation loop were displaced only one Burgers vector from its atmosphere, it would be unlocked. Applying his model to the special case of delayed yielding under a constant stress of the order of the upper yield strength, he demonstrated that the delay time 7 for yielding should depend on stress and temperature according to where A and B are constants, G is the shear modulus, and u and T are the resolved shear stress and absolute temperature, respectively. Cottrell and Bilby, Fisher, and Fisher and Rogers' have shown that the above deductions are at least in qualitative harmony with the experimental facts. A number of investigators5-0 have shown that the yield point phenomenon can also be induced in sub-stitutional alloys of face-centered-cubic metals. In general such yield points are not as pronounced as those encountered in body-centered-cubic metals containing interstitials. The yield point phenomenon in these materials is usually enhanced by prestrain-ing at low temperatures and aging at intermediate temperatures. Undoubtedly the yield point phenomenon induced by strain aging substitutional alloys also results from locking of dislocations. But the locking of dislocations in substitutional alloys of face-centered-cubic metals differs somewhat from interstitial locking of dislocations in body-centered-cubic metals. Substitutional elements in face-centered-cubic lattices cause only radial displacements of the adjacent lattice points. Consequently, only the edge components of dislocations can be locked by the mechanism suggested by Cottrell. Additional locking, however, can be obtained by the Suzuki mcchanism.10 In face-centered-cubic metals, dislocations exhibit lower energies when they are present in the

Jan 1, 1957

By R. E. Boni, G. Derge

SURFACE tensions of molten silicates are of metallurgical importance for many reasons. From a knowledge of their values, an insight into the problem of liquid slag structure can be gained. Also, such problems as separation of slag from metal, slag penetration of refractories, spreading of enamel coats on metals, bonding of cutting wheels, adsorption of gases, frothing of slags, and homogen-ization of slags are related to the surface tensions of the silicates. Because of the absence of a correlated review of the work that has been conducted in this field, the following survey is presented. It is not a complete summary of all the surface tension studies of silicates but only a review of the literature which is pertinent to metallurgical applications and research. Liquid Surface Tension The surface of a liquid differs from the interior in that its particles (ions, atoms, or molecules) are not

Jan 1, 1957

By G. W. Binkley, G. K. Dumbauld, F. A. Brooks, B. E. Morgan

In recent years, oil well cementing compositions have been developed with low densities, controlled set strengths, and satisfactory thickening times. With the introduction of the permanent-type well completion method for cementing wells, another property—that of rate of filtration or water loss to permeable formations— has become important. Laboratory data show that cement slurries prepared with oil, water, bentonite, and calcium lignosulfonate possess satisfactory thickening times, strengths, and filtration properties for primary cementing of casing and for squeeze cementing with the permanent-type well completion technique. Cementing compositions have been prepared with oil-in-water emulsions varying in composition from 60 cc water and 20 cc oil per 100 gm cement to 90 cc water and 45 cc oil per 100 gm cement. These compositions have contained from 0.4 to 5.0 per cent calcium lignosulfonate by weight of dry cement. Slurries prepared from these compositions weigh 11.4 to 13.1 lb/ga1 and have filtration rates of from 10 cc to approximately 100 cc in 30-min API tests at room temperature. The unfiltered emulsion cements develop one-day tensile strengths of 60 to 220 psi; and the filtered mass sets to tensile strengths of 60 to 150 psi in 12 hours and develops strengths of 320 to 515 psi in seven days when cured at 125° F. Field experience gained from 13 field mixing jobs demonstrates the utility of the emulsion cement for permanent-type squeeze cementing operations. INTRODUCTION In recent years, research in oil well cementing composition has been directed toward the development of cements having low densities, controlled set strengths, satisfactory thickening times, and low rates of water loss by filtration. Two well cementing compositions that have been developed with these properties are the modified cements containing, respectively, 12 and 25 per cent bentonite clay and various concentrations of calcium lignosulfonate1,2 In a search for other ways to incorporate these characteristics in a cementing composition, consideration was given to the rheological properties of oil-emulsion drilling fluids. Many of the desirable properties observed in oil-emulsion drilling fluids are equally advantageous in a cementing composition. For example, low water loss by filtration and low density, which are inherent characteristics of these oil-in-water emulsions, are desirable for many oil well cementing operations. Furthermore, oil-emulsion slurries have lubricating properties similar to those of oil-emulsion muds, a factor which should provide ease of rotation of casing during primary cementing operations. The properties of lubrication and low filtration may be of special value in both primary and squeeze cementing operations encountered in slim-hole drilling. Studies in the preparation of oil emulsion systems have pointed out the need for violent agitation in order to disperse the oil into the water phase. It was thought, therefore,

Jan 1, 1957

By J. C. Holm

ALTHOUGH the main constituents of Portland cement are the oxides of calcium, silicon, aluminum, and iron, characteristics of the cement are seriously affected by such contaminants in the raw materials as magnesium, phosphorus, sodium, potassium, sulfur, and others of lesser importance. Sources of cement raw materials comprise a long list of minerals occurring in nature in various degrees of purity. The calcareous raw materials are generally limestone of purity varying from calcite to cement rock (a low-grade limestone of natural, almost correct chemical composition), chalk, marl, seashells, coral, and coral sand. The argillaceous raw materials supplying silicon, aluminum, and iron are mainly various forms of clay and shale, to which may be added silicious sand, iron ore, bauxite, or kaolin for minor adjustment of the chemical composition. The quality of Portland cement in this country, as in most parts of the world, is controlled by rigid specifications limiting both its chemical and physical characteristics, and cement manufacturers must comply with these specifications to market their products. Brandon Raw Materials: An unusual deposit of marl, limestone, and clay occurs 12 miles east of Jackson, Miss., near the village of Brandon. The deposit is of sedimentary origin and of relatively young geological age. Layers of marl vary from putty-like consistency to such hardness that it can be cut with a knife. Interspersed between the layers of marl are bands of limestone varying from very soft to hard. the compressive strength of the hardest layers exceeding 15,000 lb per sq in. The layers of marl range in thickness from a few inches to about 25 ft. The limestone bands seldom exceed 2 to 3 ft but often occur in thinner veins in the quarry face. Above the top layer of the deposit, which may be marl or limestone, a layer of clay ranges in thickness from a few inches to more than 20 ft. Part of this clay is harvested with the raw material to supply part of the argillaceous components, but most of it is stripped as overburden and wasted. A highly silicious clay of extreme fineness, harvested from the bottom of the quarry below the marl and limestone bands, is to correct the silica content. Fig. 1 shows typical examples of the interrelation of the various materials, based on drill logs obtained during exploration of the deposit. The marls vary in moisture content in the bank from 15 to 30 pct and contain up to 70 pct -200 mesh particles and up to 40 pct —10 p particles. A large percentage of the fine fraction is within the colloidal range, making the marl extremely sticky. The limestone beds range in hardness from that of the hardest marl to a medium hard limestone and in moisture content from 2 pct to approximately 14 pct. The line of demarcation is often difficult to draw and the moisture content is possibly the best means of classification. The ratio of soft to hard material is not constant throughout the deposit, but the average is approximately 70 pct soft to 30 pct hard material. Through the years this deposit had been repeatedly explored by cement companies and rejected as unsuitable for cement manufacture, mainly because of physical characteristics. In 1950, after careful exploration of the deposit and comprehensive laboratory and pilot plant tests of the raw materials, officials of Marquette Cement Mfg. Co. of Chicago were convinced that a practical and economical method of processing the raw materials had been devised and authorized construction of a new plant that began production in December 1951. Marl and limestone, common raw materials for Portland cement, usually occur in such a manner that they can be worked separately. Their harvesting and processing normally have presented no difficult problems, as standard equipment and methods are available for handling either sticky or hard materials. No other cement plant utilizes a deposit of the nature of that at Brandon, however, and for this reason no prior art was available for design. When properly blended, the raw materials produced an excellent cement without additives. Basic problems to be solved in designing the cement plant were:

Jan 1, 1957

WHEN Magma Copper Company in 1952 set about finding $100,000,000 to finance the project of developing and equipping the property of its lusty progeny, the San Manuel Copper Corporation, A. J. McNab, president and guiding genius for both companies (and incidentally a mining engineer by profession), determined that he would avoid the mistake frequently made in such circumstances, of underestimating the cost, and thereby running short of funds before the job was completed. The fear that this might happen was one of the reasons why insurance companies, one potent source of "big" money, were reluctant to finance the enterprise. How, they asked themselves, would Magma, a relatively small company, get additional money in such a contingency? Insurance officials' thumbs were turned down. Conditions Imposed by R.F.C. The upshot was the negotiation by Mr. McNab for San Manuel of a contract with the Reconstruction Finance Corporation, dated July 10, 1952, whereby needed monies in amount up to $94,000,000 would be advanced as a loan, bearing 5 per cent interest. Arrangements were made for the separate financing of the new $10,000,000 town, needed for the project, through the Del E. Webb Construction Company of Phoenix, Arizona, and M.O.W. Homes, Incorporated, of Los Angeles. Thus the $94,000,000 drawing account was believed ample to provide for building the railroad, the mine plant, the concentrator, and the smelter, as well as for the underground development of the mine needed to start production. As a matter of fact, only

Jan 1, 1957

Jan 1, 1957

By Bernt Ellingsaeter, Terkel Rosenqvist

IN the silicothermic reduction of magnesia, burned dolomite is treated with high grade ferrosilicon in an evacuated steel retort at temperatures between 1150° and 1200°C. The following reaction is assumed to occur MgO + CaO + 1/2 Si (Fe) - Mg(g) +- & Ca,SiO, + Fe with the equilibrium constant on the basis of thermodynamic data for the substances involved and assuming unit activity for all solid constituents, Kubaschewski and Evans' calculated the magnesium pressure as a function of temperature logp,, (mmHg) = 15.06-1.61 T- log T- 13,16O/T. Pidgeon and King," who measured the magnesium pressure by means of a flow method, found values about three times the calculated ones. This may be caused by uncertainties in the thermodynamic data, but may also be caused by the formation of other reaction products, such as Ca,SiO,, which is known to be the stable silicate in equilibrium with lime. Whatever the exact reaction may be, it is evident that as long as all other factors are maintained constant the magnesium pressure will vary with the silicon activity, viz: p,, = &,. (p,,) ", where (p,,)" is the magnesium pressure by the reduction with silicon of unit activity. In the present investigation, p,,, was therefore measured for various grades of ferrosilicon and their silicon activities were calculated. The experimental method was similar to that used by Pidgeon and King. Briquettes of burned dolomite and Fe-Si alloys were placed in a 1 in. heat resistant steel tube and were heated to 1200°C. By means of a flow of purified hydrogen, the magnesium vapor was swept into a condenser filled with steel wool. From the amounts of hydrogen used and magnesium condensed the magnesium partial pressure was calculated. First a tube of 28 pct Cr steel, and later a tube of Kanthal D (a ferrous alloy with 22.6 pct Cr, 2 pct Co, and 4.5 pct Al), was used as a heat resistant tube. The latter tube showed the best heat resistance. The dolomite used had the following composition: 43.6 pct MgO, 55.5 pct CaO, 0.2 pct K,O + NalO, 0.2 pct Fe,O,, and 0.3 pct insoluble. The ferrosilicons were prepared from 98 pct Si of technical grade (0.7 pct Al, 0.3 pct Ca, and 1 pct Fe) by melting with various amounts of electrolytic iron of high purity. The alloys thus obtained were analyzed on their iron and silicon contents, which added up to between 99 and 100 pct. The amounts of reactants were chosen so that there would always be an excess of the oxides, and the average decrease in silicon content during the experiments would be about 1 pct. Most of the reaction occurred in the part of the reaction mixture facing the gas flow. The change in the silicon concentration in the part facing the condenser was, therefore, negligible. To facilitate the reaction, about 1 pct fluorspar was added to the briquette mixture. Fluorspar does not enter the reaction, but is known to act as a

Jan 1, 1957

By A. J. de Witte

INTRODUCTION The importance of determining dips of subsurface formations in wells, especially in wildcat wells, is self-evident and need not be enlarged upon. Various dipmeter instruments have been described in technical literature1,2,3,4 over the years. The introduction of the continuous dip-meters3,4 has made the earlier types obsolete. Continuous dipmeter logs are run by at least two different major service companies. Included as part of the service are a limited number of dip calculations—usually 10—made at different levels from the log. Very frequently this is the total result of a dip survey. It is believed that dipmeter surveys would be of considerably more advantage if geologists and engineers were able to make their own calculations from the original records. Determination of dips from the dipmeter record starts with the correlation of three log curves taken at different sides of the borehole. It cannot be over-emphasized that the quality of the results hinges primarily on this correlation. Nobody should be better qualified to correlate logs than a subsurface geologist or field engineer. The next requirement is to have an easy yet accurate way of computing the dip from the correlated points. Service companies use a mechanical device for this purpose. Directions for a graphical method were given in a recent article by B. 0. Prescotts. This paper describes a different graphical technique which, in our experience, is simpler, faster and at least as accurate. The entire manipulation is carried out on the stereonet in a number of easy moves. The paper is divided into two parts. This first part contains the introductory sections and full explanation of the geometry involved. The second part reviews the reading of data from an actual field log and summarizes the practical rules for computation of dips, the whole process being illustrated by an example. Following the outlined procedure, one could calculate a good many levels in a relatively short time, thus being able in particular to check suspected anomalies such as fault zones or unconformities in as close detail as the log will permit. GENERAL EXPOSITION OF THE METHOD Prnciple of the Dipmeter The position of a plane in space is defined by the location of three points, not on a straight line. Referring to Fig. I, if a borehole traverses a bedding plane, we can determine the strike and dip of the bed by finding three points which are not in line along this plane. Such points as A, B, and C are obtained with the dipmeter. The device consists of three electrodes (or caliper arms)1, 2, and 3 spaced at 120 angles, as schematically indicated, whose readings are separately recorded (Curves 1, 11, 111, to the right). When electrode 1 passes the boundary of the bed, Curve I will kick, etc. From these curves, we know the relative distances of points A, B, C, measured along the axis of the hole. If A is at zero, then B and C are at levels d1 and d2 up the hole,

Jan 1, 1957