Search Documents

By W. H. Wamsley

Used in combination with conveyor belt haulage, bucket wheel excavators offer unusual possibilities for low excavation and haulage costs. Originating in Germany, these machines are now in use or on order for Australia, Northern Rhodesia, the Belgian Congo, Italy, Yugoslavia, France, Belgium, Indonesia, and the Union of South Africa. A diamond mine in South Africa that has been using German bucket wheel excavators since 1928 purchased American cable-way excavators and American scraping equipment after the war. Operating cost for this equipment was double that for the bucket wheel machines operating in the same mines with crawler-mounted stackers. Machines built and operated in the U. S. are, as far as the writer knows, confined to the northern Illinois coal field, where they are used in conjunction with large shovels to strip overburden too high to be reached by the 30 to 40-yd shovels. Their long stacker belts can deposit the spoil far enough behind the coal face to avoid slides, in such a manner as to make reclaiming the land easier. These large, specialized machines are now being made by Bucyrus-Erie Co. but are not adaptable to many open pit mining situations.

Dec 1, 1956

By J. P. Zannaras

If we assume that testing of the model started at time C, that time t2 was the instant at which the elastic limit of the material was passed at the points of the maximum stress, and that at time t3 the failure of the model was completed as shown in the typical photograph (Fig. 1), then actually the photograph shows the final results of what took place between time t2 and t3. By the principle of similitude all conclusions drawn from the behavior of the model were applicable and valid for actual mine roofs up to the time t, after time t, motions and friction came into play during the destruction of the model. The events between t2 and t3 and the photograph itself are not representative of the events expected in an actual mine roof unless corrections imposed by the principle of similitude are made.

Dec 1, 1956

By J. R. Dawson, J. A. Glunt

Vesta No. 4 and 5 mines supply most of the high volatile coal required for Jones & Laughlin's by-product coke plants. Until 1944 all coal produced in these mines was loaded by hand. Pressure to mechanize at Vesta was brought on by the manpower shortage in World War II, and in 1943 a decision was made to change to mechanical loading. It was the opinion of those concerned that by use of selective mining the coal would be clean enough to be processed by the existing preparation plants. At that time coal cleaning at Jones & Laughlin consisted of hand picking the larger sizes at the mine tipples and wet washing at plants located at the Pittsburgh and Aliquippa Works. A typical section of the Pittsburgh seam as it occurs at Vesta is shown in Fig. 1. The 14 to 16 in. of drawslate immediately over the coal is too soft to be used for roof and must be taken down, leaving the rooster coal just above for roof. In selective mining an attempt is made to mine the coal under the drawslate first and then load out the drawslate separately as refuse. In full seam mining slate and coal are shot down at the same time and loaded out.

Dec 1, 1956

By Eldred D. Wilson

Apropos of metals low in the series illustrated by Dr. Butler's Table II, it is interesting to note that Cress and Feldman reported traces of platinum metals in several samples of alunite. They found, chemically and spectrographically, several traces of platinum, palladium, and rhodium in alunite from Sugar Loaf Peak, near Quartzite, Ariz.; silver, platinum, and rhodium in alunite from Rio Grande County, Colorado; and traces of rubidium and gallium in various samples of alunite. These authors stated that the platinum metals appear to be present as oxides and suggested deposition by hydrothermal solutions under near-surface conditions.

Dec 1, 1956

By R. R. Hartman, W. B. Agocs

In the course of a return flight from Olympia, Wash., to Laramie, Wyo., an airborne magnetometer profile was recorded continuously. The level of flight was controlled at barometric levels along segments of the flight. Barometric altitude was changed from 3000 ft to a maximum of 12,000 ft above mean sea level to take care of topographic variations. Terrain clearance varied from 800 to 7300 ft. Horizontal positions were obtained by recording and tying to cities, towns, airports, river crossings, and other landmarks in the course of the flight. Figs. 1-6 show the course of the flight and the general geologic and tectonic features traversed. The flight line begins south of Olympia, Wash., and proceeds south across the Puget-Willemette depression to the Columbia River. Thence it proceeds eastward along the Washington-Oregon border across the Cascade Mts. and lava flows and the Umatilla basin to Pendleton, Ore. From Pendleton it traverses the Blue Mts. uplift of Oregon in a southeasterly direction, and then to the Boise basin of southwestern Idaho. The flight line swings in an easterly direction as it passes over the Snake River downwarp to the south of the Idaho batholith. It then passes over the northern portion of the Great Basin and the heavily overthrust area at the intersection of the Utah, Idaho, and Wyoming borders. The flight then assumes an easterly course to cross the series of basins and uplifts of southern Wyoming and terminates near the western flank of the Laramie uplift.

Dec 1, 1956

By R. I. Williams

Kennecott Copper's mining activities in Arizona are conducted by the Ray Mines Div., located in Ray, Ariz., in the Mineral Creek mining district about 60 miles southeast of Phoenix. The Ray orebody lies in a mineralized zone belted on the east, west, and north by well defined faults. The orebody consists principally of schist with intrusions of quartz porphyry and diabase. The dominant ore mineral in the schist and quartz porphyry is chalcocite, with some native copper, and in most areas the orebody has been heavily oxidized. In the diabase the dominant ore mineral is chalcopyrite. Ore deposition in the schist portion is very erratic, with no apparent structural explanation. In 1873 silver prospectors opened the mining district, but it was not until 1899 that an English company made the first major attempt to exploit the copper deposits. This venture failed because of improper sampling and limited development work. In 1904 D. C. Jackling, Seeley Mudd, and Philip Weiseman became interested in the Ray Copper Co. and the Gila Copper Co., which later merged as Ray Consolidated Copper Co. In 1926 the Nevada Consolidated Copper Co. took over Ray Consolidated and in turn was taken over by Kennecott Copper Corp. in 1933. The extensive program of surface and underground development and exploration begun in 1907 continued through successive changes of management and ownership to the present time.

Dec 1, 1956

By H. Herbert Hughes

In the years following World War II, L. de Roll S.A., Zurich, Switzerland, perfected its vertical kiln. De Roll first became interested in cement-manufacturing equipment in 1947, not only kilns but also the crushing, grinding, and handling equipment required for a complete cement plant. The parent company, Louis de Roll Iron Works, S.A., Gerlafingen, Switzerland, was founded in 1804. In its six plants, and with its associated companies, de Roll manufactures and installs equipment for a wide variety of industries-chemical and metallurgical operations, fats and oils plants, and municipal refuse incinerators and sewage disposal installations. Vertical shaft kilns, of course, are as old as Portland cement itself. Their fuel economy has long been recognized, particularly in Europe where fuel costs are high. But the disadvantages of old-type shaft kilns have been the lack of consistent quality of the clinker, the small capacity, and the relatively high labor costs.

Dec 1, 1956

By Robert F. Love

Deep under the hills of southwestern Wyoming lies a nonmetallic mineral deposit of incredible dimensions and value. This nearly pure, horizontal bed of the mineral trona, a sodium sesquicarbonate (Na2HC0,.NaHC08.H20), is found in the Green River formation some 1500 ft below surface. It is believed that evaporation of an ancient saline lake left this sodium carbonate as the evaporite and mysteriously left practically no sodium chloride, which is the common constituent of an evaporated saline lake. The trona bed averages 10 ft in thickness and extends over an area of several hundred square miles. In 1938 a geologist with the U. S. Geological Survey identified the trona in the core from a former oil exploration drillhole. By so doing, he initiated the developments of a chemical industry of impressive growth in the area, an industry on the threshold of further and much more spectacular growth. A drilling program by the Union Pacific Rd. and Intermountain Chemical Co. in the early 1940's succeeded in blocking out mineable reserves of several hundred million tons. Development of the deposit started in 1946 with the sinking of a 12-ft diam, concrete-lined shaft 1500 ft deep-followed by construction of a small pilot calcining plant. Actual mining of the trona started in 1947 and continued on a limited scale until 1953, when the $15 million surface facilities were completed, along with the second shaft and other expanded underground facilities. Since April 1953 the mine has been producing more than half a million tons per year, from which the refining plant has produced more than 300,000 tons per year of high quality soda ash.

Dec 1, 1956

By T. M. Berry

In the past few years changes have taken place in shaft sinking. Progress has been made with types of machinery designed, developed, and made available to shaft sinking contractors. This is particularly true of drilling and mucking equipment. Compared with conventional clamshell loading, mucking or loading with a crawler-mounted overshot loader is a new technique for shaft work. There are several methods of clamshell loading. Dravo Construction Co. mounts an air tugger on the clamshell to operate the closing line. The load, or holding line, is attached to the hoist of a crane or whirler at the shaft collar. The clamshell is raised or lowered by the hoist when a signal is given by a bell or light system operated by men at the bottom of the shaft. Two men control the drift of the clamshell with tag lines, pulling it to any position in the shaft for loading, or over the shaft muck bucket for emptying. One man operates the air tugger to open and close the clamshell by means of two lines attached to the operating air valve, just as reins are used to drive a horse. One man operates the signal telling the hoist operator when to raise or lower the clamshell. This method requires two hoisting lines in the shaft-the line from the mine hoist that lifts

Dec 1, 1956

By Dale I. Hayes

Combined loader and transport, the Gismo is now built for sale in one size, 5 to 6 tons. It will operate in a minimum opening of 7x7 ft and can be built to operate at lower heights. Where space limitations are not a factor it could be designed with much greater carrying capacity-12, 18, or 25 tons-to be powered with a standard heavier tractor. The Gismo is mounted on crawler tracks of the same design as the tracks of the small Allis- Chalmers HD-6B tractor used to power it. With the HD-6B tractor it will negotiate upgrades of 12 pct and downgrades of 20 pct. The next tractor size would make the device feasible for steeper grades or for a machine of larger capacity at moderate grades.

Dec 1, 1956

By A. R. Sims

Are from the Greater Butte Project is hoisted through the new Kelley shaft. In 1946 when plans were formulated for the Kelley mine, two test cave blocks were mined by using the facilities of the old St. Lawrence mine. These blocks, known as the Adams No. 1 and Adams No. 2, produced more than half a million tons of ore. The experiment proved beyond all doubt that cave mining was possible- and economical-in Butte. Adams No. 1 was patterned after Inspiration cave blocks. Adams No. 2 was a slusher type, with the slusher lane on the first floor above the haulage crosscut and at right angles to it. Thirty-horsepower electric hoists slushed ore from 48-in. scraper buckets directly into cars for haulage to the shaft. These cars were the 57-cu ft Granby type hauled by 6-ton battery locomotives over 40-lb, 18-in. gage track. Prior to this time the largest slushing machines used at Butte were 15-hp electric hoists pulling 36-in. scrapers.

Dec 1, 1956

By Allen R. Rowen

One of the greatest deterrents to more widespread use of manufactured lightweight aggregate is the fact that no industry-wide standards for its application exist. It is true that ASTM has specifications covering lightweight aggregate, but they are so broad as to be of little assistance in mix design work. Today even an engineer who has worked with one lightweight aggregate may be faced with re-education on his next light- weight concrete job if he is in an area served by another producer. Manufacture of lightweight aggregates has grown with the country, appearing in the patent literature at least as early as 1875, when a patent was issued covering use of burnt clay aggregate as an admixture in manufacture of artificial stone. The widely known Haydite came into the picture prior to 1920 as a result of work by Stephen J. Hayde, and there have been many others since who have contributed significantly to the growth of the industry and its technology.

Nov 1, 1956

By D. J. Reed

Concord coal mine near Bessemer, Ala., built, owned, and operated by Tennessee Coal & Iron Div., U. S. Steel Corp., produces only a metallurgical grade for use as coke in blast furnaces of the division at the Fairfield and Ensley works. Capacity of the operation is approximately 800 tph, half of which is delivered to the coke and coal chemical plant at Fairfield after beneficiation to metallurgical grade coal. The remaining portion of the mine run is rock and refuse removed during preparation. Concord mine coal is hoisted to the surface coal preparation plant by an underground slope conveyor. The slope conveyor is 2449 ft long and has a lift of 729 ft. At time of installation the Concord mine slope conveyor was the largest single conveyor unit ever made with respect to belt horsepower and total lift. After several years it became necessary to determine the cause of slope conveyor cover wear.

Nov 1, 1956

By F. Weston Starratt

The opening of a new large-scale beneficiation plant is always news, but the start-up of Cleveland-Cliffs Iron Co.'s Eagle Mills near Ishpeming in Michigan's Upper Peninsula early in October is of particular interest because of the completely different type of operation being carried on at this plant. The ore boat which left Marquette, Mich. on the 3rd of October bound for the plant of Wisconsin Steel Division of International Harvester, not only carried the first output of this new mill, but also carried the first agglomerate made from the Upper Peninsula's jasper ore, the first commercial output from an updraft traveling-grate furnace, and the first large-scale commercial application of the balling disk, also called the flying saucer, to the agglomeration of an iron flotation concentrate.

Nov 1, 1956

By E. J. Roberts, E. B. Fitch

Most classifiers in use today are, in function, settling pools. A fluid suspension of particles is passed through a pool at such a rate that only a fraction of the particles-the coarser fraction-has time to settle out of suspension. The rest are carried on out of the pool as overflow. The most fundamental way in which such classifiers differ is in the mechanism used to remove the settled particles from the pool. The particles may gravitate from the pool, as in the various sand cones, or they may be conveyed mechanically from the pool by drags, spirals, or reciprocating rakes. The mechanism of settling pool classification and its limitations are discussed. A method for calculating countercurrent classifications is presented. The practical validity of the calculation method has been confirmed through 20 years of use within The Dorr Co. During this time it has been used on diverse feeds and has been checked against many types of settling pool classifiers, with close agreement in nearly every case. Excellent elimination of third critical mesh particles and finer ones may be obtained in a countercurrent classifications series where all stages separate at the same mesh, but elimination of first and second criticals is inherently limited. Spectacular elimination of all criticals may be obtained by arranging successive stages to classify at successively coarser mesh. Improvement in elimination is obtained at the cost of an increased internal recirculation, but this may be tolerable in many cases.

Nov 1, 1956

By Paul L. Allsman

Butte mining district contains extensive manganese vein deposits forming a peripheral zone. Oxidation in the veins studied usually extends to a depth of about 75 ft. Secondary minerals formed by oxidation were found to be ramsdellite-always accompanied by intermixed pyrolusite-and cryptomelane. Enrichment of the gossan is accomplished by reduction of weight upon oxidation; theoretical enrichment is 32.2 pct. Additional enrichment is caused by leaching of soluble minerals, particularly calcium and magnesium carbonates. Butte mining district contains extensive manganese vein deposits in the outer zone, surrounding the copper and zinc deposits and corresponding to the well known silver zone. This article describes the mineralogy of the manganese veins, the oxidation and enrichment processes, and the use of this information in prospecting.

Nov 1, 1956

By W. L. Kendrick

At Henderson, Nev., Manganese Inc. is mining by open pit methods a low grade manganese ore averaging 21 pct Mn, concentrating it to 42 pct by flotation, and agglomerating it to produce nodules of metallurgical grade-about 48 pct Mn. The striking aspect of the whole operation, and one that has considerable effect on nodulizing, is the use of approximately 250 lb of reagent per ton of mill feed. For many years rotary kilns have been used for drying, calcining, clinkering cement and other products, and burning lime. Their use for nodulizing or agglomerating a metallic ore is new-first reported in this country in 1904, when a small rotary kiln at South Chicago was employed to nodulize flue dust from a blast furnace. After a short time this process was replaced by sintering.

Nov 1, 1956

By Harold Bloom, H. E. Hawkes

Streams and rivers are the principal channels into which the weathering products of rocks and their contained ores are funneled. The inorganic load of a stream system is a crude sample of all the earth materials in the drainage basin of the stream, and the heavy mineral assemblage of sediments is one of the oldest and most successful guides to certain kinds of bedrock ore in unexplored terrain. Early application of this method was made possible by the ease of separation and identification of heavy minerals in the field with the simplest equipment. Water analysis for traces of base metals became a practical possibility about eight years ago with the development of rapid chemical tests that could be carried out at the field site. Since that time the water method has been widely used in mineral reconnaissance, and a substantial number of discoveries have been reported. Here again, the techniques developed for this work were relatively simple and could be performed easily at the field site.

Nov 1, 1956

By J. P. Zannaras

Referring to the article by R. J. Charles and P. L. de Bruyn, let us assume that W = weight of glass bar; P = weight of hammer; e = total deformation; E = unit of deformation; K = potential stress energy; E = modulus of elasticity; L = length of the bar; 7, = coefficient of inertia; h = height, ft; V = velocity, fps; and a = cross section area. The portion of kinetic energy which is effective in producing stress energy in a fixed bar struck horizontally is given by the formula [ ]

Nov 1, 1956

By J. S. Mitchell

Cobalt recovery from arsenical concentrates by pressure leaching and reduction involves special methods and operating problems. Principal steps in the process are auto-oxidation acid leaching under pressure, filtration of the tailings, purification of the solution, hydrogen reduction of the ammoniacal solution, and electrical furnacing for sulfur removal and granulating the metal. Extracting cobalt metal from arsenical ores has presented a major metallurgical problem for many years. In acquiring the Blackbird mine near Salmon City, Idaho in 1943 Calera Mining Co. accepted the challenge to solve this problem.

Nov 1, 1956