Search Documents

By Bernhard Blumenthal

A melting process was developed by which high purity electrolytic uranium crystals can be converted into sound ingots without serious contamination. Careful preparation of the crystals, melting in a high vacuum, and directional solidification led to a metal of better than 99.993 wt pct purity. The metallographic examination showed a substantially clean metal with only residual amounts of a second phase which responded to heat treatment. The density of high purity uranium is 19.05 g per cu cm. FOR the study of the fundamental properties of uranium and its alloys, a base metal of high purity is needed, and an investigation was started at Argonne several years ago to examine various methods of preparing high purity uranium. Early success was achieved by the fused salt electrolysis process in preparing high purity metal in crystal form,' and the problem became that of melting the crystals into ingots without contamination. The electrolytic crystals contained a few ppm of heavy metals, less than 15 ppm C, and large quantities of potassium and lithium in the form of trapped fused salt electrolyte. On melting in vacuo in magnesia or urania crucibles, the metal picked up considerable quantities of carbon and some iron, copper, and silicon but lost most of the potassium and lithium. It was not metallographically clean, and much research work was necessary to determine the optimum melting conditions for minimum contamination. This work has resulted in the development of a melting procedure by which sound ingots can be prepared with only a limited contamination by carbon. In the section entitled "Melting of the Electrolytic Metal," the equipment and processes that have been developed for melting the electrolytic crystals are described in detail. The "Metallography" section is devoted to the metallography of high purity uranium, and the section "Density of High Purity Uranium" contains the first property measurement on high purity uranium—a density determination. Melting of the Electrolytic Metal Apparatus—Melting and Vacuum Equipment: Uranium may be melted in either resistance or induction-type electric furnaces. Resistance heating was found to be preferable to induction heating for melting down the electrolytic crystals, for several reasons: Although induction heating permits fast heating, this advantage cannot be utilized when crucibles with limited thermal shock resistance are used. Temperature control of induction-heated melts is poor, and the stirring effect increases the rate of contamination of the melt from the crucible, slag, or the furnace atmosphere; liquation and controlled solidification are difficult to carry out. Because of these objections, resistance heating was chosen. A 10 kw Globar resistance furnace of low heat capacity permitted uniform heating of a uranium charge to its melting point in 45 min. The furnace was insulated with a removable aluminum shield so that, after melting and removal of the shield, the furnace could be quickly cooled to room temperature. The furnace was equipped with an apparatus for directional solidification; see Fig. la. The crucible was suspended in the center of the furnace; and when the melting was complete, the crucible was slowly lowered into the cold end of the furnace tube. Solidification took place upward from the bottom; and when the rate of lowering was small, a sound ingot free from sink holes and shrinkage cavities was produced. To remove the large quantities of gas contained in the electrolytic crystals, melting in a high vacuum is mandatory. While, from the standpoint of contamination, melting in a highly purified argon atmosphere appeared feasible, lithium and potassium removal proved less efficient under such conditions. Also, a vacuum-melted ingot has a cleaner surface than one melted in an inert atmosphere. The vacuum system must be of very high pumping speed and leak tight so that a vacuum of less than 2x10-7 mm Hg is attainable when the system is pumped down cold. The system must have a high pumping speed, so that the pressure maximum which may rise to 1x10-4 mm during heating can be quickly reduced

Jan 1, 1956

By A. L. Pranatis, G. M. Pound

Changes in length of copper foils of varying thickness and grain size were measured under such conditions of low stress and high temperature that it is believed that creep was predominately the result of interboundary diffusion of the type recently discussed by Conyers Herring. The surface tension of copper was calculated and results confirmed previous work within the limits of experimental error. Under the assumption of viscous flow, viscosities were calculated as a function of temperature and grain size. Predictions of the Nabarro Herring theory of surface grain boundary flow were borne out fully and the Herring theory of diffusional viscosity is strongly supported. ONLY a relatively few techniques for obtaining the surface tension of solids are presently available. Of these, the simplest and most straight forward is the direct measurement of surface tension by the application of a balancing counterforce. Thin wires or foils are lightly loaded and strain rates (either positive due to the downward force of the applied load or negative if the contracting tendency of surface tension is sufficiently greater than the applied stress) are observed. By plotting strain rates against stress, the load which exactly balances the upward pull is found and a simple calculation yields a value for the surface tension. The technique is of comparative antiquity, and solid surface tension values were reported by Chapman and Porter,' Schottky; and Berggren" in the early part of the century. Later, the filament technique became fairly well established as a method for determining the surface tension of viscous liquids, and Tammann and coworkers,'. " Sawai and co-worker and Mackh howed good agreement between the values of surface tension for glasses and tars obtained by the filament technique and by more conventional methods. With the increased confidence in the technique gained in these experiments, the method was applied to solid metals and the first reliable values of surface tension of solid metals were reported by Sawai and coworkers10' " and by Tammann and Boehme." More recently, Udin and coworkersu-'" have reported the results of experiments with gold, silver, and copper wires. Similar experiments with gold wires were carried out by Alexander, Dawson, and Kling.'" The excellent review articles of Fisher and Dunn" and of Udinl@ should be referred to for detailed criticism of the foregoing work and for discussion of underlying theory. In all the foregoing calculations, it is assumed implicitly that the material contracts or extends uni- formly along the length of the specimen and also that it flows in a viscous fashion, i.e., that strain rates are proportional to stress. For an amorphous material, such as glass, tar, or pitch, the assumptions are quite valid and good agreement is obtained with values of surface tension measured by other techniques. The values reported for metals, however, are occasionally regarded with misgiving, since it can be argued that, because of their crystalline nature, true solids can not deform in a viscous fashion. If this is true, then the results reported for solid metals over a long period of years are of only doubtful value. Thus it is clearly necessary that a mechanism be established that would explain both the viscous flow and the uniform deformation that has been assumed. Such a mechanism has been proposed by Herring."' Briefly, he suggests that, under the conditions of the experiment, deformation takes place by means of a flow of vacancies between grain boundaries and surfaces. This is a direct but independent extension of the theory proposed by Nabarro" in an attempt to explain the microcreep observed by Chalmer~.In a condensed form the Herring viscosity equation is TRL there 7 is the viscosity, T the absolute temperature, R and L grain dimensions, and D the self-diffusion coefficient. In its complete form, all constants are calculable and it includes such factors as grain shape, specimen shape, and degree of grain boundary flow. When applied to existing data, good agreement was obtained between predicted and observed flow rates. The theory received provisional confirmation from the work of Buttner, Funk, and Udin" who observed viscosities in 5 mil Au wire much higher than those in the 1 mil wire used by Alexander, Dawson, and Kling.'" More significant were the completely negligible strain rates found by Greenough" in silver single crystals. Opposed to these observations were those of Udin, Shaler, and Wulff'" who found indications of viscosity decreasing as grain size increased. Thus, complete confirmation of the theory was lacking in that the data to which it could be applied contained only a limited number of grain sizes. Hence, it was proposed that a series of experiments be carried out with thin foils of varying grain size up to and including single crystals, where, according to the Herring theory, deformation would occur only at almost infinitely slow rates.

Jan 1, 1956

By H. H. Rachford, W. P. Schultz

The use of computing machines to solve physical problems has made it imperative to represent physical data in a form computing machines can use. Although curve-fitting is an old and well-practiced art, there still seems to be some interest in questions regarding what methods can be used and why. Even though there are many good references on this subject, it may be of some value to discuss a particular method which has been found to be useful, and to make available the associated tables for its use in the hope that there can be saved a few of the tedious hours necessary to reduce many of the suggested methods to practice. Although a very brief discussion of the mathematical background of the tables is included immediately below, those interested only in their use can skip directly to the section on Use of the Tables. Direct Fit of a Set of Points A frequently encountered problem is: Given data which can be represented by a smooth curve +(x), to find an easy-to-evaluate function F(x), with only a few coefficients, which is a good approximation of +(x) on the interval 0 5 x 5 x,,. Consider F(x) as a linear combination of m + 1 arbitrary, single-valued, continuous, linearly independent functions, f,(x), Ff.r) = a,f,,(x) + a,f,(x) + . . . -+ aifi(x) + If the value of Q(x) is known or can be read from the curve at the points xj: +(x,), +(x,), . . . +(xj) . . . +(x.), and if n = m, then all the coefficients of F(x) can be determined, and F(x,) — +(x,) = 0 for j =. 0, 1, . . . n. This follows from the solution of the set of linear simultaneous equations. +(x<.) = aofu(x,) + aJI(x0) + . . . + a,,f,,(x,) =a, = f,,(x,) + a,f,(x,) + . . . + a,f,,(x,) +(x,,) = a,,f,(x,,) + a,f,(x,) + ... + a,,f.,(x,,) ...........(2) for the coefficients ai. Although the set a, from the solutions of the set of Equations 2 yields an fix) which gives an exact value of $(x,) for the n + 1 points, there is no restraint on ~(xj in the interval xi < x < xj+,. Indeed, if the points +(x,) are not sufficiently smooth, very serious differences may arise between F(x) in the interval and the smooth curve +(x). Least-Squares Fit It has been suggested&apos; that if n is made to exceed m, and the set a, is found to minimize the function the function F(x) is much less sensitive to small errors in +(xi), and usually provides a much better fit to the smooth function +(x). This is known as the best fit in the sense of the least-squares error. To minimize $, set £ = 0,i = 0,1,... iTi,.....(3) The m + 1 equations from Equation 3 are k—n k=n a.^p /,,(a) f,(xt) + a, X A: = 0 k=O k = n k = n k=0 k=0 +(x.) f,(x,),............(4) one equation being obtained for each i = 0, 1, . . . m. Inasmuch as the arbitrary functions f(x) may be evaluated for x,, k = 0, 1, . . . n, and the +(x,) are known values of the curve to be fitted, the simultaneous Equations 4 may be solved for the set a,. Particular Functions Given the functions fi(x) and the set +(xj), the solutions for require evaluating a number of sums of products as well as the solution of an m + 1 order set

Jan 1, 1956

By Paul B. Crawford, Bobby L. Landrum

Electrical model studies have been made of the effect of unsymmetrical vertical fractures on production cnpacity. The study war restricted to the case of two vertical fractures originating at the well and extending out into the reservoir for various distances and orientations. The ratio of the short fracture length to the long fracture length was varied from 0.1 to 1.0 in successive studies. The angle separating the two fractures was varied from 0 to 180 degrees. The most effective fractured patterns were obtained when the fractures were oriented 180 degrees. It was found that when the total fracture length was equal to 0.2 of the drainage radius, the increase in production capacity may vary from approximately 1.55 to 1.95. depending upon the ratio of the short fracture length to the long fracture length and the angle separating the two fractures. If the total fracture length were 0.5 of the drainape- radius. poroduction cavacitv., increases varving 1.95 to 2.65 were observed, depending on the angle between the fractures and the ratio of the .short fracture length to the long fracture length. The fractured well production capacity decreased aPproxin?ately I to 10 per cent as the angle separating the fractures was varied from 180 to 90 degrees. It was dependent on the particular fracture. The commercial application of reservoir fracturing techniques has caused an interest to be expressed in the effect of vertical and horizontal fractures on production capacities. Some data have indicated that substantially vertical fractures may be created in some reservoirs. It is believed that the fractures are possibly unsymmetrical, that is, one fracture may extend due north 100 ft and a second fracture on the opposite side of the well may extend south or southeast only 50 ft. The total fracture length, ratios of the lengths and angles of separation may vary considerably. For this reason variations in these factors were considered. The study was restricted to the case of two vertical fractures originating at the well and extending out into the reservoir. It is not known that such will occur in a reservoir, but the results may be of value in interpreting or studying fracturing applications. PROCEDURE An electrical model was used in this study of the effect of unsymmetrical vertical fractures on production capacity, A wooden tank 30 in. in diameter and approximately 2 in deep was coated with paraffin wax. A copper band was situated at the periphery and a single wire electrode was positioned at the center of the tank. The ratio of the reservoir radius divided by the

Jan 1, 1956

By I. Sheinhartz, H. M. McCullough

DURING the course of a lubrication study in relation to the compacting of metal powders, it became desirable to measure the thickness of sprayed graphite coatings on steel dies for hot pressing. The thickness of these lubricant coatings ranged between 0.0001 and 0.002 in. In their particular case, the authors were interested in a method for measuring the lubricant thickness on tapered die inserts having curved surfaces. The lubricant was sprayed on the inserts at an elevated temperature and it was desirable to measure the thickness as soon as possible after application. Various standard types of commercial equipment were tried. Most of the available devices operated on either a mechanical or magnetic principle. The mechanical devices, such as micrometers, dial indi-

Jan 1, 1956

By M. M. Fine

Small-scale laboratory mineral-dressing studies were made on a total of nine individual or composite samples of manganese-bearing material from the west-central Arkansas, or Mena, district. Of these, only three yielded concentrates that would probably be acceptable for purchases by the Federal Government fur the National Stockpile. Concentrates from some of the other properties, however, contained more than 40 percent Mn and might be merchantable to other purchasers of manganese ore. In most instances, a too-intimate association of manganese oxides and gangue is conducive to low grade, low recovery, or both, so that mechanical concentration processes do not promise much for this district.

Jan 1, 1956

By R. R. Trengove

This paper is one of a series published by the Bureau of Mines on mining methods and operation practices. It describes the open-pit mining method and operations of the Kaiser Steel Corp. Eagle Mountain iron-ore mine, which is in the extreme southeastern part of California 175 miles east of Los Angeles in Riverside County. Nearest town to the mine is Indio, which is 60 miles away by an excellent highway (fig. 1). Elevations at the deposit vary from 1,400 to 3,000 feet. Figure 2 is a plan map of the Eagle Mountain iron mine. Kaiser Steel Corp. built a model camp at the mine, with all modern conveniences (fig. 3). The camp, comprising 145 homes, dormitories, mess hall, commissary, post office, and recreational facilities for 600 people, is at 1,390-foot elevation. The area has winter-resort weather between October and May, with occasional drops of temperature to 25° at night. From June to September temperatures sometimes rise to 1200 during the day. Rainfall is scant, approximately 2 inches a year, the majority of which comes as cloudbursts during the summer months.

Jan 1, 1956

By Edwards A. B

Re-opening of the old Proprietary mine has provided new exposures of the system of uralite dolerite dykes observed in 19110 by the Geological Sub-Committee of the Scientific Society of Broken Hill. The newly exposed dykes have been invaded and replaced by the massive ore, with development of manganese garnet and biotite adjacent to the sulphides. A similarly altered dyke in massive ore has been encountered in the North Broken Hill mine.The textures of the unaltered portions of these dykes indicate that they have not been affected by the intense regional metamorphism that has recrystallized the other rocks of the area. Moreover, in mineral composition and textures, in chemical composition, and in cross-cutting relations, they are so similar to the uralite dolerites of the district which post-date the folding and metamorphism of the Broken Hill area, that they must be regarded as typical members of this suite of post-metamorphic dykes.The invasion and replacement of the dykes by the massive sulphide ore, and their metasomatic alteration adjacent to the invading sulphides, establishes that the lode was formed after the dykes were intruded, so that the high temperature features of the ore cannot be attributed to metamorphism and recrystallization, but are primary features of high temperature hydrothermal deposition.INTRODUCTIONTwo cross dykes are recorded on the plan of the 300-ft. level of the Broken Hill lode accompanying the report on the geology of the Broken Hill lode published by the Geological Sub-Committee of the former Scientific Society of Broken Hill (1910). One dyke occurs in Block 12, and the other in Block 13, and both were stated to consist of a dark basic amphibole rock, called diorite for convenience. The more southerly dyke was traced from some distance out in the footwall, and even through the lode, by means of occasionalpatches of it still existing in the ore, in a direction...

Jan 1, 1956

By B. L. Averbach, M. Cohen, C. H. Shih

The isothermal formation of martensite is studied in Fe-Ni-Mn and Fe-Mn-C alloys under conditions where the athermal transformation is completely avoided, there being no martensite present at the beginning of the isothermal reaction. The initial rate of martensite formation is extremely low under these conditions, but it increases greatly as soon as some martensite is formed. It appears that true initial characteristics of the isothermal reaction can be studied only in samples wherein the formation of martensite on cooling is completely eliminated. THE phenomenon of isothermal martensite formation is well established1 -" but the observations have been made in the presence of varying quantities of athermal martensite. Complete avoidance of athermal martensite and the formation of martensite under pure isothermal conditions have been reported by Kurdjumov and Maksimova2 in an Fe-Ni-Mn alloy (23 pct Ni, 3.4 pct Mn, and the balance Fe) and have been confirmed by recent experiments of Cech and Hollomon in a similar alloy. In each case, the isothermal transformation rate was a maximum at the beginning of the transformation and decreased as the reaction proceeded. These initial transformation rates were used by Fisher7 for the confirmation of calculated nucleation rates based on classical nucleation theory extended to include the effect of elastic strain energy. Cech and Hollomon have admitted, however, that up to 3 pct martensite formed on cooling in their samples and thus was present at the initiation of their isothermal runs. In this paper, experiments on similar alloys are described, except that care was taken to remove the incidental martensite developed at the surface prior to the isothermal reaction. It is shown here that the reaction rate at the beginning of the strictly isothermal reaction is very low. As soon as some detectable amount of martensite is produced, the transformation rate increases rapidly but ultimately decreases as the reaction proceeds. When martensite is allowed to form isothermally in the presence of about 2 pct of prior martensite, the apparent initial reaction rate is a maximum and corresponds to the observations of Kurdjumov and Maksimova and Cech and Hollomon. It is evident that the cooperative nature of the martensitic reaction results in a significant stimulating or autocatalytic effect on the isothermal reaction rate. Experimental Procedure The chemical compositions of the alloys used in this investigation are listed in Table I. The Fe-Ni-Mn alloys A and B were melted in an induction furnace, cast into ingots 2 in. diam by 4 in. long, and forged into % in. diam rods. The manganese steel (alloy C) was melted in an arc furnace and cast into ceramic molds 1/4 in. diam by 5 in. long. The rods were sealed in evacuated Vycor tubes and homogenized at 1175" to 1200°C for 50 hr. The long homogenization resulted in some manganese loss from the surface, producing a thin layer of transformed material. This surface layer was removed by grinding and the specimens were then swaged to 0.050 in. diam wire. Measurements of electrical resistance were made with a Kelvin double bridge to follow the course of the martensitic transformation. A small permanent magnet was also useful in scanning an entire specimen for small localized quantities of martensite. This test is almost as sensitive as the electrical resistance method in detecting the presence of martensite (which is ferromagnetic in these alloys) and it was especially useful in deciding whether a specimen was completely free of martensite. The wire specimens (0.050 in. diam by 2.5 in. long) were sealed in evacuated tubes and austenitized for 5 min at 1150°C. The specimens were quenched into water and, unless otherwise stated, stress-relieved for 1 hr at 650 °C in order to induce greater uniformity in the subsequent martensitic transformation. As dem-

Jan 1, 1956

By R. G. Treuting

Germanium single crystals strained in tension at 600°C slip on the {Ill} plane and, macroscopically at least, in the <110> direction. Deformation is in homogeneous: various localized rotations are observed, as is a banding consistent with secondary slip banding. The structure after deformation is polygonized with a domain size of about 2x1O-3 cm. In relaxation tests, an incubation period prior to flow is observed, of duration inversely related to temperature and applied stress. Under continuous loading, there is a sharp first yield point. A critical resolved shear stress therefore must be cited with respect both to temperature and to rate of loading. At 600°C, when loading proceeds at 2900 psi per min, it is 1310 psi. The yield point phenomenon is suggestive of Cottrell&apos;s solute atom atmosphere theory and five points of qualitative agreement with this theory are found. PLASTICITY of germanium at elevated temperatures has been reported by Gallagher,&apos; who ascribed it to slip on {Ill) planes and described some associated effects. Preliminary experiments with single crystals of silicon and germanium loaded as simple beams confirmed {ill) as the slip plane of both materials.V his was demonstrated by the standard technique employing traces on two surfaces of known angle on a deformed crystal of known orientation.3 These experiments did not fix the slip direction, since more than one glide system operated. Uniaxial tensile straining is preferred for this purpose in order to restrict slip to one predominant system and to provide an unequivocal determination of the orientation change with respect to the stress axis. Experimental Method Specimens were diamond-sawed from germanium crystals containing about 5x10-5 wt pct Sb prepared by the zone-leveling process described by Pfann and Olsen;4 these specimens measured about 81/2 in. long, 0.20 in. wide, and were of various thicknesses from 0.035 to 0.060 in. Prior to testing, a specimen was coated over 1 in. or more of length at each end with Apiezon wax, chemically polished (in a solution of 15 ml HF, 25 ml HNO,, 15 ml CH3COOH, and 3 to 4 drops Br2), and dewaxed in warm xylene. A brief re-etching after scribing through a complete wax coating with vernier dividers provided gage marks at 0.200 in. intervals on the polished surface. A specimen with grips soft soldered to the ends was passed through the furnace tube and the grips pinned to the tensile machine in series with a stress gage. The Schopper testing machine is best described by reference to the illustration on p. 107 of Schmid and Boas5 and is operated with the pendulum arm locked, fixing the upper head. Load is applied through the screw-driven lower head, manually or by reduced speed motor. The furnace is 21/2 in. long surrounding a 4x7/16 in. ID quartz tube and was positioned about the specimen to permit free motion. The inert or reducing atmosphere required was sufficiently provided by a flow of helium introduced at the center of the furnace tube, with the tube ends loosely plugged with asbestos paper. Surface corrosion was slight. The stress gage employs a Be-Cu strip with SR-4 units incorporated in a simple bridge network with provision for balancing and calibrating. The bridge output on loading is fed through a Leeds and North-rup dc amplifier to a Speedomax 10 mv recorder, and calibration is obtained by dead loading. Experiments of two types have been conducted. Most have been in relaxation at constant elongation. One stress-strain curve has been taken with the machine continuously driven. Following extension of a specimen, Laue X-ray photographs were taken to obtain the orientation change between deformed and undeformed regions, recorded on a single film by translating the specimen in a plane normal to the beam between exposures. Sequences of such multiple exposures were made on some specimens to include the entire orientation range on one film. Slip Direction To obtain a maximum orientation change with a single slip system, crystals of very closely <110> axial orientation were used. The classic determination of slip direction rests on establishing that direc-

Jan 1, 1956

By H. B. Brunot

On April 26, 1949, the Bureau first approved a machine designed to replace the cycle of cutting, blasting, and loading coal by a single operation. This machine took the coal directly from the solid face and delivered it to transportation equipment. By January 1, 1955, 30 approvals for designs of machines of this type had been granted by the Bureau. In the main, this paper describes briefly the action of the various designs approved as permissible. In addition, the approval number, the date of approval, the voltage of the power supply, the number and character of the explosion-proof accessory parts, the size of the trailing cable, and the overcurrent protection at the outby end of the trailing cable are given for each design. Since no similar information has been published by the Bureau, it is hoped the material in this paper will be valuable in giving the mining public an organized look at the various machines of this nature that have been approved as permissible by the Bureau.

Jan 1, 1956

By G. W. Lester, T. J. Nowak

The paper presents a practical method of utilizing pressure fall-off data obtained when a water injection well is shut in for determination of: (I) the static reservoir pressure, (2) the potential water injective capacity (md-ft) of the formation, and (3) the formation damage (skin effect) surrounding the wellbore. In the development of the method, equations are presented which give The theoretical background for predicting the behavior of water injection wells. Certain physical factors which limit the application of the method are discussed. The procedure and the relevant precautions in obtaining the data are discussed. A sample analysis and computation from an actual pressure fall-off curve is illustrated. Fintrlly, general characteristics of pressure fall-off curve! obtained in several reservoirs are presented. INTRODUCTIO N Theoretically, in an injection well the flow of water into the formation will continue as long as the sand-face pressure is greater than the reservoir pressure. However, in practice, engineers have observed that upon stopping injection and opening the wellhead to atmospheric pressure, some wells backflow water for time intervals ranging from several seconds to several hours although the sand-face pressure, as calculated from the hydrostatic head, is considerably greater than the static reservoir pressure. Further, field observations indicated that upon shutting in a water input well, the wellhead pressure does not drop off immediately, but a pressure decline occurs lasting from several seconds to several days. These observations make it evident that when an input well is shut in, a residual pressure lingers in the vicinity of the wellbore which is greater than the average reservoir pressure. This residual pressure declines first rapidly, then more slowly, to the static reservoir pressure: therefore, it is called transient back-pressure or pressure fall-off. The first step in investigating the mechanism of pressure fall-off is to establish what general conditions are necessary for its occurrence, and to this end, Dickey and Andresen1 have presented a qualitative explanation describing the mechanism. They point out that the formation pressure gradient in the vicinity of the well does not disappear immediately when the input well is shut in, as if the system were filled with a totally incompressible fluid, but it is maintained by the expansion of the compressible fluids and by the elasticity of the formation. In such a compressible system the decrease in pressure is possible only to the extent that the water front continues to advance until the pressure is equalized. The principal aim of this paper is three-fold; namely. (1) to present a theoretical quantitative analysis of pressure fall-off data, (2) to present an application of the developed theory to field data, and (3) to discuss the general characteristics of actual pressure fall-off curves. Under (I), theoretical equations dealing with such factors as compressibility of the fluid-reservoir system, mobility of the fluids and certain physical restrictions that

Jan 1, 1956

By F. W. Jessen, John C. Miller

In many areas where carbonate rocks form important parts of the stratigraphic sequence, stratigraphers have experienced varying degrees of difficulty in differentiating and correlating limestone and dolomite units in both surface and subsurface work. With early Paleozoic rocks of the Mid-Continent, insoluble residues yield a remarkable amount of strati-graphic data and relatively good correlations may be carried over broad distances.&apos; Unfortunately, neither such information nor electric logs and radioactive logs have been particularly helpful in interpreting the limestone sections of the Permian Basin of West Texas. This is because: (1) the variations in the sections may be very slight; (2) no completely satisfactory method of interpretation has been developed; and (3) the measurements themselves are not sensitive enough for small variations. Also, such logs are influenced by the fluid content. Paleontology and micro-paleontology remain the ultimate arbiters. As a routine tool, however, paleontol-ogical examination is slow and tedious. Chemical analysis may be used, but this, too, is extremely slow. Although rocks are not classified according to chemical composition, there is considerable variation with rock types. Correlation by chemical composition has two advantages, first, the characteristics determined are subject to minimum human error and interpretation, and secondly, the lithologic changes are not masked by fluid content as in the case of electric and radioactive logs. Some fossils concentrate certain elements which tentatively might be used to date rock units.&apos; Rapid chemical analysis by spec-trographic means could be used as an adjunct to other means employed in correlation work, or might, in itself, present a suitable method. PURPOSE OF THIS INVESTIGATION Sloss and Cooke&apos; have published data concerning spectrographic analysis of limestone rocks specifically for purposes of direct correlation of a single formation. These authors found satisfactory evidence that differences in percentage of four elements (Mg, Fe, Al, and Sr) in the Mississippian limestones of northern Montana were useful in carrying out correlation of this formation over a distance of approximately 50 miles. It was concluded from the preliminary work that the spectrochemical method offered possibilities of solution of some problems of correlation heretofore not possible. Since the work of Sloss and Cooke&apos; was confined to one particular limestone zone, extension of the use of the method to examine two or more geologic formations would aid materially in the over-all problem of correlation of such rocks. Equipment is now available commercially with which very rapid spectrographic analyses may be made, and hence the problem was to determine whether the variations existing in the minor constituents of limestones were sufficient for use in possible correlation. Qualitative and semi-quantitative investigations were made to determine whether significant changes in the chemical condition occurred. It was a further purpose to investigate the geologic time-boundaries to see whether significant chemical variation could be found corresponding to the paleontological breaks. It was desirable to attempt correlation of a thick section of limestone or dolomite rock and to have as much information as possible on the section. Furthermore, it was felt that examination of formations more difficult to correlate by other means would enhance the value of the method should definite points of correlation be found. Samples were chosen from the Chapman-McFarlin Cogdell No. 25 well in the Cogdell field, Kent County, Tex., and from the General Crude Oil Co., Coleman No. 193-2 well in the Salt Creek field, Kent County, Tex. These fields belong to the famous series of "Canyon" reef fields of West Texas. Cores from the above wells were available from the United States Geological Survey, Austin, Tex. THE SPECTROGRAPHIC METHOD The choice of procedure to be followed in this investigation was based on the anticipated requirements peculiar to the problem. Since the problem was primarily to investigate the possibilities of applying the spec-trograph to problems of correlation in thick carbonate sections, a precise quantitative analysis did not appear necessary. A qualitative analysis to show the possible absence of presence of any element, or a semi-quantitative analysis of the elements present to show the relative changes in magnitude of selected elements was required. Both types of analysis were employed. The two most widely applied methods of semi-quantitative estimates are those of Harvey and of Slavin4,5 though various other procedures have been described.6 while the Harvey method has been modified by Addink,7 this refinement did not seem necessary to the present problem. Essentially, the procedure employed is a variation of the total energy method of Slavin with two exceptions: (1) stressing matrix effect, and (2) using densitometer measurements. As measured by a densito-

Jan 1, 1956

By R. W. Stahl

Methane, a highly explosive gas evolved during the coal-formation process, is one of the hazards of mining most difficult to overcome. It is retained between particles of coal and entrapped in strata overlying and underlying the coal beds to a degree dependent upon the permeability of the enclosing strata. Considering that methane might be encountered at any time during the mining of coal, attempts have been made through the years to minimize the sources of ignition at coal-mine faces, such as the introduction of permissible electric equipment, the prohibition of smoking and open lights, and the development of safer explosives. The sparks created when mining-machine picks contact sandstone or iron pyrites2/ constitute one source of ignition, always recognized as a possibility but never greatly emphasized in the United States until recently, when ignitions began occurring with rather alarming frequency and in widely scattered coal-producing areas.

Jan 1, 1956

By D. J. Carney, C. W. Boquist, E. C. Rudolphy

Effect of variations in sinter feed composition on sinter strength, bulk density, re-ducibility, chemical composition, and microstructure were determined by sintering experimental samples on a production sintering machine. Increasing amounts of roll scale, ore fines, return fines, and blast furnace slag were most beneficial to feed permeability, sinter bulk density, and strength. Burnt lime additions improved feed permeability but were not beneficial to sinter strength or bulk density. Sinter reducibility was adversely affected by all additives. DEVELOPMENT of methods for evaluating sinter quality, which would in some way predict the behavior of the sinter during charging and smelting in the blast furnace, has been given considerable attention in recent years. In a previous investigation at South Works of the United States Steel Corp., standard sinter sampling and testing procedures were developed.1,2 By modifying the sinter sampling device, a method of sintering experimental mix sinter samples upon a production Dwight-Lloyd sintering machine was also developed. This technique afforded a rapid and controlled method of investigating the effects of the various raw materials and additives on sinter quality and was used in this present investigation. Since the beginning of the present study in 1953, the results of numerous sinter investigations have been published, most of which were concerned with production tests of iron ore sinter, both here and abroad. Three groups of investigators reported results of experimental sinter studies that were related to this investigation. Voice et al.3 studied the effects of controlled variables on sinter quality by producing and testing experimental Northants iron ore sinter using an experimental sintering unit. Mor-rissey and Powers&apos; determined the relationship between iron ore sinter quality and the moisture and coke content using a small laboratory sintering system. Burlingame et al.5 studied the effects of "additives" upon iron ore sinter using a laboratory sintering apparatus and laboratory grade raw materials. At South Works, it was considered desirable to study the effects of sinter mix composition and additives upon the quality of a flue dust-base sinter produced on a production sintering unit. Extrapolation of controlled laboratory test data to sintering plant operation lacking such precise control is not altogether satisfactory. Therefore, the present study was conducted in a manner which approximated production conditions as closely as possible. The raw materials used were those commonly encoun- tered in the production of flue dust and flue dust ore-type sinters and these were varied within extremes encountered in this type of sinter production. Experimental Procedure The experimental sinters were produced from 100 lb mixtures of sinter feed. The principal raw materials and additives used, their particle size, and approximate chemical composition are listed in Table I. The mixing of the raw materials was accomplished by means of a miniature single shaft pug mill shown in Fig, 1. The use of the pug mill as a mixer was decidea upon after encountering difficulty in reproducing the mixing and chopping effect of the sinter plant pug mill with other types of available small mixers. The miniature pug mill was constructed, consisting of 31/2x2x1/4 in, blades spaced 3 in. apart along a 3 ft shaft. Preliminary tests were run with this small mixer to establish the proper rotation speed and the required number of passes through the pug mill to thoroughly mix and distribute all the raw materials in a manner approximating the production Pug mill- Although the effects of varying the mosture content were determined in one particular series of tests, the amount of moisture added was changed as the composition of the experimental mix was varied. The aim in making water additions was to achieve a permeability as high as possible for each particular

Jan 1, 1956

By J. Chipman, J. A. Cordier

Equilibrium in the reaction H2 (g) + 2 = H2S (g) was studied at 1600°C for sulphur dissolved in Fe-Ni alloys of 0 to 100 pct Ni. Within experimental accuracy, the equilibrium ratio pH2s/pH2 [pct S] is independent of the Fe-Ni ratio. Its variation with sulphur content is the same in nickel and the alloys as in iron. Recent data on dissociation of S2 into atomic sulphur are used to apply a small correction to earlier equilibrium data. Equations are presented which define the thermodynamic properties of sulphur in liquid Fe-Ni alloys. ACTIVITY of sulphur in liquid iron was determined by Sherman, Elvander, and Chipman.&apos; The effects of a number of alloying elements on the activity of sulphur also have been determined, that of silicon by Morris and Williams,2 that of carbon by Morris and Buehl,8 and the effects of manganese, phosphorus, and aluminum by Sherman and Chip-man.&apos; The data of Rosenqvist and Cox5 have been used to establish the effect of copper. A summary of all of these data is included in the paper by Sherman and Chipman. In each case, the experimental method depended upon the study of equilibruim in the reaction of sulphur in the liquid metal with hydrogen gas to form H,S. Despite wide differences in the design of apparatus used by the several investigators, all of the results are in excellent agreement. Experimental Study Since the experimental method has already been described,&apos; it will be sufficient to mention its general

Jan 1, 1956

By J. L. Martin, W. M. Campbell

A new electric logging method, called displacement logging, often gives a direct indication of the presence of mobile hydrocarbons in hydrocarbon-bearing formations. This method is based on the detection of a bank of connate water which is formed between the invading mud filtrate and virgin formation fluids in these cases. The existence of this phenomenon has beer, verified by laboratory studies and by actual field logs taken in known oil sands. INTRODUCTION During the past decade increasing use has been made of conventional electric logs to determine the amount of oil or gas in formations traversed by a borehole. This determination requires knowledge of several factors, such as true resistivity of the formation, formation factor, and water resistivity. Sometimes all of the factors necessary to make a reliable saturation calculation are not available. Also, the computations and corrections which are necessary in such a study often require the services of an experienced log analyst. It has long been the desire of exploration people to have a logging device which will locate hydrocarbon-bearing formations directly without requiring complex interpretation methods. The displacement log, while not completely fulfilling this desire, appears to be a Step in that direction. Basis for the Device The basis for this device stems from a phenomenon which occurs when mud filtrate invades a formation which contains displaceable hydrocarbons. As the mud filtrate invades the formation, most of the oil or gas is pushed out of the invaded zone, leaving residual oil. However, in addition to displacing most of the oil or gas, the connate water is also swept out, since the originally irreducible water is mobile in the presence of a water phase.1,2,3 Tonsequently, this irreducible water piles up as a bank between the virgin oil zone and the invading filtrate. If the mud filtrate is of higher resistivity than the formation water— as is commonly the case—the resulting annular zone, containing the bank of formation water, will be of lower resistivity than either the virgin oil-bearing formation resistivity or the invaded zone resistivity. This resistivity configuration, going from high to low to high again as the distance from the borehole increases, is found only in those zones which contain displaceable hydrocarbons. A device which would reliably detect this low resistivity zone would give a direct indication of mobile hydrocarbons. Illustrations This phenomenon is illustrated in Fig. 1 and 2. Fig. 1 shows a sketch of a zone containing salty connate water plus displaceable hydrocarbons, along with graphs showing fluid content and electrical resistivity vs distance from the borehole, before invasion occurs. Fig. 2 shows this zone, together with fluid content and resistivity graphs. after invasion by a fresh water mud. The resistivity pattern on moving away from the borehole is high: low: high. The absence of the low zone phenomenon in water zones is illustrated in Fig. 3 and 4. Fig. 3 shows a sketch of a zone containing salty formation water and residual oil, along with graphs showing fluid content and electrical resistivity vs distance from the borehole, before invasion occurs. Fig. 4 shows this water zone, together with fluid content and resistivity graphs, after invasion bv a fresh water mud. In this case the resistivity pattern on moving away from the borehole is high: low since there is no change in water saturation at the head ol

Jan 1, 1956

By Stefan Boshkov

THE ADVENT of mining at great depth has brought to the fore the question of stresses around mine openings. The many-pronged attack on this problem is certified by the accelerated appearance, in the mining literature, of articles on various topics related to this subject (1). Whereas it may be agreed that we, of the mining profession, have fallen woefully behind in research and the development of an understanding of this important facet of the general problem of mining, it must also be accepted that the analysis of the stresses in a mine structure is usually more complex than is the case in the majority of structures encountered and dealt with in civil engineering. Whereas homogeneity and isotropy are readily acceptable for most metals, such properties are but crudely approximated in rocks. Whereas the external loads on a structure in civil engineering may be readily determined, those on a mining structure are subject to ?conjecture. Whereas the limits of the structure may readily be defined in civil engineering, the boundaries of the mining structure are, in most cases, indeterminate, and subject to intelligent guesswork, at best.

Jan 1, 1956

By M. J. Sinnott, H. B. Probst

AN extensive survey of the factors which affect austenite grain growth has already been made.&apos; These factors are temperature, time at temperature, rate of heating, initial grain size, hot-working, alloy content, ofheating,initialand rate of cooling from the liquidus-solidus temperature. In the present work, a vacuum-melted temperature.electrolytic iron was used and the variables studies were temperature, time at temperature, and prior ferrite grain size. Other factors were maintained constant. The iron used in this study was vacuum-melted electrolytic iron of nominal composition of impurities of 0.07 wt pct. It was supplied as a ½ in. round cold-drawn bar. This iron was tested in three conditions: as-received, annealed 6 hr at 1200°F, and annealed 6 hr at 1600°F. Samples were ? in. disks cut from the bar. The prior anneals were carried out in vacuum and the isothermal treatments were carried out in vacuum-sealed Vycor tubing. The thermal etch technique was employed to determine the austenite grain size. Prior to sealing the test specimens, one surface of the sample was polished metallographically. This surface, after heating, was examined to determine the austenite grain size, since the austenite boundaries are revealed by thermal etching. This is essentially the only technique available for measuring the austenite grain size of low carbon steels or pure irons without altering the composition. It has been shown to yield results that are in agreement with other methods used for determining austenite grain sizes.&apos; The specimen size was quite large compared to the grain size measured, so inhibition of growth due to size effects is probably negligible. After vacuum sealing, each sample was placed into a furnace at temperature and at the completion of the run was quenched into a mercury bath. The growth temperatures used were 1700°, 1800°, 1900°, and 2000°F controlled to -~10"F. Growth times were varied from 10 to 240 hr. The long times were used in order to eliminate the nucleation and growth effects occurring during the initial transformation. Time was measured from the introduction of the capsule into the hot furnace to the time of quench. Grain-size measurements were made with the use of a grain-size eyepiece of a microscope. By determining the number of grains per square millimeter at X100 and taking the square root of the reciprocal of this number, the average linear dimension of the grains was determined. Figs. 1 and 2 are plots of these data as a function of time and temperature for the various conditions investigated. The variation of D, the linear dimension of the grains, was assumed to follow the equation3 D = A tn. The curves of Fig. 1 were obtained from the data by the use of the least-squares method of analysis. Fig. 1 is for the growth of the as-received stock and Fig. 2 is for growth after prior treatments. Differentiating the foregoing equation gives an expression for the rate of growth dD/dt = G = nAtn-1 = nD/t. Both D and G as functions of t are given in Table I. It should be noted that G is a function of time; the growth rate is rapid at early stages and decreases with increasing time. Since increasing temperature increases the growth rate, it has been common practice to use the empirical relationship G = Go e-Q/RT to relate temperature to growth rate. The growth rate customarily has been taken at constant values of D on the basis that the rate of growth is related to the boundary surface tension and this is measured by the curvature of the boundary. At constant D values, the growth rate is a function of time and temperature. The growth rate can be related however to temperature at constant time, and this has the advantage that under these conditions the growth rate is a function only of temperature. Obviously the Q values, activation energies, obtained for each assumption will not be the same and the question of which is the more correct is a moot one, since the assumed exponential relationship in either case has no particular theoretical significance. By plotting G, at constant grain size, vs 1/T, the activation energy over the temperature range of 1800" to 2000°F is found to vary from 30,000 cal per mol at the smaller grain sizes to 50,000 cal per mol at the larger grain sizes. The 1700°F data do not correlate with the data at higher temperatures. The activation energies for the 1200" and 1600°F prior annealed materials were calculated as 50,000 and 62,000 cal per mol, respectively, using the reciprocal time to a given grain size as a measure of the growth rate. Plotting G, at constant times, vs 1/T yields an activation energy of 12,300 cal per mol for the tem-

Jan 1, 1956

Jan 1, 1956