Search Documents

By R. Webeler

In order to study the role of work hardening in the fatigue process, use was made of the great sensitivty of the resistivity of AuCu to cold work. A change of the resistivity of AuCu of the order of 1 to 2 pct at the temperature of liquid nitrogen was found to occur as a consequence of severe fatigue. ACCORDING to Orowan's theory,' the process of fatigue In metals 1s associated with the production of a number of small regions which have undergone strain hardening. This phenomenon is supposed to occilr even if the stress applied during fatiguing is always smaller than the yield stress. In an attempt to verity the existence of such regions, Welber and Webeler' undertook to detect the stored energy associated with severe fatigue in copper. Previous experiments" had shown that the energy stored in a sample of copper which has been cold worked by torsion is released in the temperature range between 150" and 250°C when the sample is heated from room temperature and that no more energy is released (or absorbed) between 250" and 450°C. In particular the stored energy amounted to 0.41 cal per g for a case in which the mechanical energy expended in twisting the sample was 11.9 cal per g. In the case of fatigued copper, however, no release of stored energy could be detected between 150" and 250°C, so that the experimental error of &0.02 cal per g represents an upper limit for the amount of energy stored in strain hardening., It seemed desirable to attack the problem in a new fashion. For this purpose, it was decided to make use of the fact that, if an alloy capable of undergoing the order-disorder transition is ordered and then cold worked, the resistivity, p, increases very greatly above the value for the ordered state even if the deformation is very small. Some insight into the nature of the fatigue process may be obtained then by measuring the resistivity of an ordered sample before and after subjecting it to fatigue. For reasons which will become apparent from the following remarks, considerably more can be learned by carrying out the resistivity measurements at two different temperatures. In the case of a material containing impurities, vacancies, dislocations, or other imperfections of essentially atomic dimensions, the resistivity, p, according to Matthiessen's rule, can be represented as a sum of two terms p = p, + p, where p, is the (temperature dependent) resistivity of the pure metal, and p, is the temperature independent contribution of the imperfections. Briefly, the physical basis for this rule is the following: The main contribution of the impurities in question to the resistivity results from the fact that they interrupt the periodicity of the lattice and thus scatter the conduction electrons with a probability which is almost independent of temperature. In order that this be the case, it is necessary that the' extension of the impurities be small enough—roughly less than one electron mean free path—so that their main effect on the resistivity occurs for the foregoing reason. If an alloy like AuCu is partly or completely disordered by quenching from an appropriate temperature, Matthiessen's rule also applies to a very good approximation* with p, representing in this case the resistivity po of the ordered sample and p, the additional (temperature independent) resistivity due to the disorder. In general, the disorder can be represented in terms of atoms which are displaced from their "proper" positions in the superlattice and which thus qualitatively represent the imperfections in the superlattice responsible for the term p,. Since the misplaced atoms are distributed at random throughout the super-lattice, their contribution to the resistivity still can be considered in terms of the scattering of conduction electrons by lattice defects. The situation is somewhat more complex in the case of an alloy disordered by cold work because the process of disordering here does not involve a random redistribution of the atoms; however, Matthiessen's rule also holds in this case. Whenever Matthiessen's rule does apply, the values of the quantity /3 = (p? — /(T, — T,), where p, and p, are the values of the resistivity at two fixed temperatures, T, and T,, respectively, is constant (independent of p,) for a given alloy or metal. In particular, if a sample of AuCu is subjected to ordinary cold work, the value of /3 remains equal to Po, the value for the ordered material. According to Orowan's theory,' as remarked before, a fatigued sample contains a large number of isolated severely cold-worked regions, which make up only a small proportion of the metal. Thus, if a sample of AuCu initially in the ordered state is fatigued, more or less disordered regions will be produced within the ordered material. If these regions are small enough so that Matthiessen's rule applies, then it follows from the previous discussion that /3 again will remain equal to Po. If the effect of fatigue is to produce cold-worked regions which are macroscopic—of the order of at least several electron mean free paths—the effective resistivity, p, has to be computed by use of the ordinary laws of large-scale electrodynamics. For the sake of simplicity, it will be assumed here that the cold-worked regions are completely disordered and have a resistivity, p,. For a given proportion A of disordered regions the effective resistivity, p, for the current in a given direction depends on the geometrical configuration of these regions. In any case, the value of p for such

Jan 1, 1956

By J. J. Arps, T. G. Roberts

Since the introduction of the relative permeability concept in the middle thirties1,2 various investigators have shown3,10,11,12,15 how the basic equations for the flow of oil and gas through porous media can he utilized to compute the recovery from depletion type or solution gas drive type reservoirs under certain conditions, when the necessary physical data pertaining to the reservoir rock and its reservoir fluids are known. In the study by Muskat and Taylor" in 1945, the effects of viscosity, gas solubility, shrinkage, and the permeability-saturation characteristics of the producing formation on the production histories and the recovery of gas drive reservoirs were analyzed. Each parameter was varied a limited number of times, while keeping the others constant. The work was not carried to the point where the data could be used directly to estimate the primary recovery in those cases where certain rock and fluid characteristics were known or could be assumed. Since the publication of this classic study, the work by Beal in 194616 and Standing in 1952'" has established general correlations of oil viscosity and shrinkage with gas solubility and oil gravity. In addition. a considerable number of relative permeability relationships for different types of reservoir rocks has been published2,5,13,17,19,20. Also, the burden of the numerical work required in the solutions of the differential equation has. during the last few years, been greatly reduced with the availability of modern electronic computing facilities. The purpose of this paper is therefore to present the results of a large number of such recovery computations covering the normal range of variation of the main parameters such as the type of rock, the API gravity of the oil, and the amount of gas in solution. As is to be expected, the ultimate recovery is found to increase with the oil gravity. except for the higher solution gas-oil ratios. Within the normal range of solubilities, the ultimate recovery generally appears to decrease with the amount of gas in solution for the higher oil gravities, and to show a slight increase for the lower oil gravities. Intermediate oil gravities seem to fall between the two trends. The type of reservoir rock, as identified by its relative permeability relationship, appears to have a very pronounced effect on the ultimate recovery. In general, sands and sandstones show higher recoveries than limestones and dolomites, although certain intergranular limestones seem to show a higher theoretical recovery than unconsolidated sand. The recovery from sands and sandstones generally decreases with increasing cementation and consolidation, while the recoveries from limestones and dolomites are highest for the intergranular type and lowest for the fracture type porosity.

Jan 1, 1956

By M. E. Volin

To extend or delimit the known ore reserves of the Black Wonder manganese de-posit, the Bureau of Mines undertook an exploration project consisting of trenching, underground excavation, long-hole drilling, and sampling. The mineralization is spread over 6 square miles containing numerous small individual manganese deposits. There has been only small production from some of these deposits; however, simultaneous operations from many such small deposits could contribute considerably to the production from the district. A custom mill to treat oxide ore for battery use was built near Patterson in 1942 by the General Dry Batteries Co., Inc. It operated during World War II and was removed in 1944 when the manganese mines ceased operation. Except for some small experimental shipments, there has been no activity in the district since that time.

Jan 1, 1956

By P. E. Cavanagh

FOR THE PAST seven years Mr. W. Simpson, Chief Mechanical Inspector for the Nova Scotia Department of Mines, has carried out exhaustive field trials of non-destructive inspection equipment in the coal mines of that Province. This work has demonstrated the usefulness of a number of types of non-destructive inspection when used for periodic inspection of hoisting and haulage equipment in the coal mines of Nova Scotia. As a result, the Dominion Coal Company has instituted a programme of regular preventive maintenance inspection ?by a special staff of qualified and trained men. The purpose of this present paper is to describe how non-destructive testing techniques are used on ropes, axles, couplings, and other hoisting and haulage equipment, how these methods are being used in other industries, and the expected benefits from intelligent and properly organized use of these techniques in the coal mining industry.

Jan 1, 1956

By T. L. Joseph, G. Bitsianes

The gaseous reduction of dense iron ore is a topochemical process in which reduction takes place at distinct interfaces between solid phases or layers. Under normal conditions, these interfaces remain parallel to the exterior surface of the ore body as they move inward. Certain conditions, such as cracking, high porosity, impurities, entrapped residual oxides, may cause departures from normal topochemical behavior. THE gaseous reduction of dense iron ore proceeds at interfaces between several solid phases or layers.',' Under normal conditions, these interfaces progress inward and remain parallel to the exterior surface of the ore body. This topochemical behavior is clearly illustrated in Fig. 1 which shows partially reduced specimens of natural and synthetic hematite. Using a coordinated sequence of macro, micro, and X-ray examinations, the authors1-'2 found that the number of interfaces and participating phases was in agreement with the Fe-0 system. Above 570°C, reduction of the ore involved a maximum of three common boundaries between four solid phases: iron, wiistite (Fe,O), magnetite (Fe,O,), and hematite (Fe,O,). Below 570°C, reduction proceeded through two interfaces between three phases: iron, magnetite (Fe,O,), and hematite (Fe,O,). The decrease in the number of phases below 570°C was due to the instability of wiistite below this temperature. The sequence of phases was also consistent with the equilibrium requirements. For example, the layers of iron oxides that were formed in topochemical fashion were always orientated in the order of increasing oxygen content. Thus, in Fig. 1 an outer layer of metallic iron is followed in turn by a thick intermediate band of black wiistite, by a thin layer of light magnetite, and finally by a relatively large core of hematite. This arrangement of the oxide layers was due to restrictions in reducing conditions which were imposed by the physical structure of the solid. The highly reducing gas on the outside of the particle gradually lost its reducing power as it penetrated into the specimen. On a macro scale, the layers of the various oxides appeared to be sharply defined and uniform in composition. Microexamination of the sections, however, revealed that the interfaces did possess measurable widths which varied with the porosity and chemical activity of the oxide phase undergoing reduction. For example, Fig. 2 shows three interfaces in a dense hematitic ore which was partially reduced at 850°C. At the iron-wiistite interface where the greatest porosity developed, the reaction proceeded over a zone 25 to 30 microns in width. Toward the interior, the interfaces became progressively narrower until at the magnetite-hematite boundary the reaction zone was about 1 micron wide. In this region the structure was exceedingly dense; the hematite possessing a porosity on the order of 3 pct. A careful micro study across polished layers of the various oxides revealed generally homogenous and single-phase structures. As reported in a previous paper,' the wiistite layer was characterized by an increase in oxygen content with depth of penetration. The topochemical behavior of reduction was studied in six types of ore of different origin, composition, and physical structure. In most cases, reduction proceeded at the boundaries of well defined layers or phases, and this behavior may be regarded as normal for most dense fine grained ores. Deviations from Ideal Topochemical Behavior A number of deviations from the normal topochemical behavior were noted. In these cases, the continuity of the reduction interfaces was disrupted in one of four ways: 1—Cracking of the specimen interrupted the geometric configuration, and the interfacial advance was no longer parallel to the exterior surface. 2—As a result of high porosity, the interfaces were spread over an appreciable distance and all but obliterated. 3—Impurities in the ore promoted a variety of deviations, including cracking. 4—A residual oxide phase was entrapped in the reaction product and left behind the advancing macro interface. Results from Cracking: A crack leading into the interior of an ore specimen presents a path of least resistance for the counter-flow of reducing gases and gaseous reduction products. Higher reducing conditions can be maintained along such cracks and reduction accordingly will propagate well ahead of the normally advancing reduction interfaces. Cracking was caused by a number of factors, one of which was the thermal spalling of impurities in the massive form. A more general type of cracking was due to reduction and was found in all dense varieties of natural and synthetic hematite, particularly in the temperature range of 500" to 700°C. The effect is shown clearly in Fig. 3. In this case, a dense sphere of pure hematite was partially reduced at 650°C for 100 min. The macrosection shows that one large reduction crack had penetrated the specimen and disrupted the normal topochemical advance of the interfaces. The outer layer of iron was only slightly affected but the thin dark layer of wiistite, adjacent to the ferrite, had widened perceptibly as it progressed along the crack. Farther inward, the magnetite layer was greatly disrupted and had penetrated irregularly to form islands of unaltered white hematite. A great deal of internal cracking is evident in the magnetite phase. From a practical point of view, the cracking of dense ores in the blast furnace could lead to desirable as well as undesirable effects. The general result

Jan 1, 1956

By R. O. Pynnonen

This circular is a study by the Bureau of Mines of 346 accidents in underground iron-ore mines of the Lake Superior district from June 1949 to August 1954. These accidents caused 354 lost-time injuries, including 28 fatalities and 2 permanent-total disabilities. The accident reports were analyzed by the Bureau to show the causes of injuries and the time charges and unsafe practices or conditions that caused the accidents. Also shown are the times of occurrence, ages of the injured by job classification, and experience of the injured in mines and on the job being performed when hurt. Detailed information is presented on approximately 14 percent of the total number of Lake Superior district underground mine accidents that resulted in lost-time injuries during the period covered. These facts are presented to aid accident-prevention measures in underground mines and as a record for measuring future safety accomplishments.

Jan 1, 1956

By Stephen Krickovic

AS it is commonly understood in the bituminous coal mining industry, pillaring means removal, as completely as is practical, of all pillars formed in the development of headings and rooms on first mining. The degree to which this can be accomplished, termed percent of recovery, is of course dependent generally upon the physical conditions of the bottom and the overburden, the system of min-

Jan 1, 1956

By A. Spilners, M. Simnad

The rates of formation of the different oxides on molybdenum in pure oxygen at 1 atm pressure have been determined in the temperature range 500° to 770°C. The rate of vaporization of MOO, is linear with time, and the energy of activation for its vaporization is 53,000 cal per mol below 650°C and 89,600 cal per mol at temperatures above 650°C. The ratio Mo03(vapor.lzing)/MoOS3(suriace) increases in a complicated manner with time and temperature. There is a maximum in the total rate of oxidation at 6W°C. At temperatures below 600°C, an activation energy of 48,900 cal per mol for the formation of total MOO, on molybdenum has been evaluated. The suboxide Moo2 does not increase beyond a very small critical thickness. At temperatures above 725°C, catastrophic oxidation of an autocatalytic nature was encountered. Pronounced pitting of the metal was found to occur in the temperature range 550° to 650°C. Marker movement experiments indicate that the oxides on molybdenum grow almost entirely by diffusion of oxygen anions. USEFUL life of molybdenum in air at elevated temperatures is limited by the unprotective nature of its oxide which begins to volatilize at moderate temperatures. Although the oxide/metal volume ratio is greater than one, the protective nature of the oxide film is very limited. Gulbransen and Hickman' have shown, by means of electron diffraction studies, that the oxides formed during the oxidation of molybdenum are MOO, and MOO,. The dioxide is the one present next to the metal surface and the trioxide is formed by the oxidation of the dioxide. Molybdenum dioxide is a brownish-black oxide which can be reduced by hydrogen at about 500°C. Molybdenum trioxide has a colorless transparent rhombic crystal structure when sublimed, but on the metal surface it has a yellowish-white fibrous structure. It is reported to be volatile at temperatures above 500" and melts at 795°C. It is soluble in ammonia, which does not affect the dioxide or the metal. In his extensive and classic investigations of the oxidation of metals, Gulbransen2 has studied the formation of thin oxide films on molybdenum in the temperature range 250" to 523°C. These experiments were carried out in a vacuum microbalance, and the effect of pressure (in the range 10-6 yo 76 mm Hg), surface preparation, concentration of inert gas in the lattice, cycling procedures in temperature, and vacuum effect were studied. The oxidation was found to follow the parabolic law from 250" to 450°C and deviations started to occur at 450 °C. The rates of evaporation of a thick oxide film were also studied at temperatures of 474" to 523°C. In vacua of the order of 10- km Hg and at elevated temperatures, an oxidation process was observed, since the oxide that formed at these low pressures consisted of MOO, which has a protective action to further reaction in vacua at temperatures up to 1000°C. Electron diffraction studies showed that, as the film thickened in the low temperature range, MOO8 became predominant on the surface. Above 400°C MOO, was no longer observed, MOO, being the only oxide detected. The failure to detect MOO, on the surface of the film formed at the higher temperatures does not militate against the formation of this oxide, since according to free energy data MOO3, is stable up to much higher temperatures. At the low pressures employed, this oxide would volatilize off as soon as it was formed. Its vapor pressure is relatively high and is given by the equations" log p(mm iig) = -16,140 T-1 -5.53 log T + 30.69 (25°C—melting point) log p(mm He) = -14,560 T-1 -7.04 log T+1 + 34.07 (melting-boiling point). Lustman4 has reported some results on the scaling of molybdenum in air which indicate a discontinuity at the melting point of MOO, (795°C). Above the melting point of MOO,, oxidation is accompanied by loss of weight, since the oxide formed flows off the surface as soon as it is formed.5,6 Qathenau and Meijering7 point out that the eutectic MOO2-MOO3 melts at 778C, and they ascribe the catastrophic oxidation of alloys of high molybdenum content to the formation of low melting point eutectics of MOO3 with the oxides of the melts present. Fontana and Leslie -explain the same phenomenon in terms of the volatility of MOO,, which leads to the formation of a porous scale. Recent unpublished work by Speiser9 n the oxidation of molybdenum in air at temperatures between 480" and 960°C shows that the rate of weight change of molybdenum is controlled by the relationship between the rates of formation and evaporation of MOO,. They have measured the rates of evaporation of Moo3 in air at different temperatures and estimated an activation energy of 46,900 cal. This compares with the value of 50,800 cal per mol obtained by Gulbransen for the rate of sublimation of MOO, into a vacuum.

Jan 1, 1956

By S. S. Clarke, Douglas C. Brockie

Longhole underground drilling has been carried on in the Tri-State area at various times over the past 35 years or more. W. F. Netzeband reported on this topic in 1926 and in 1930. More recently it has been found that in certain areas of the Picher field, Oklahoma, and under certain conditions, the jackleg or jumbo-mounted drifters can be used more economically and to greater advantage than surface churn drillholes for prospecting. To understand better the problems involved in Eagle-Picher's longhole prospecting program it would be helpful to cover the geologic criteria affecting it. Much has been written about the geology of the Picher field. A more complete description than that given here can be found in a recent paper by J. P. Lyden.

Jan 1, 1956

P. L. Pratt (University of Birmingham, Birmingham, England)—The author has measured the hardening effect of isolated edge and screw dislocation boundaries in a remarkably elegant manner, and he proposes that the detailed structure of the boundary determines its effectiveness as a barrier to slip although "there are still unknown details of the distribution which may be extremely important." On p. 678 the author states "that for a good crystal (one having a yield of about 30 psi) a change in annealing temperature from 300" to 400 °C resulted in a negligible shift in the level of the stress-strain curve." Is this in agreement with the results of the earlier paper by Li, Washburn, and Parker8 in which such a change of temperature produced notable hardening in crystals with a yield of about 30 psi? Or were these earlier crystals, of the same nominal purity, less perfect than those used in this work? The experiment illustrated in Fig. 15, p. 681, shows that the boundary has sharpened after annealing at 400 °C, the temperature at which the hardening effect first becomes apparent. Did the author verify that no sharpening of the boundary occurred at, say, 300 °C where no hardening was found? This would seem to be an important check on the proposed mechanism, especially since zinc of this purity should polygonize at temperatures well below 400 °C within the annealing times used here. There seem to be at least two alternative explanations which could fit these facts: 1—The boundary may sharpen at 300 °C or even lower temperatures but be unable to contribute greatly to the hardening until jogged by thermal vacancies and other impurity atoms after 400 °C anneal. This mechan- ism, discussed in the earlier paper,' is believed to account for the thermal hardening observed by Blank'" in NaCl, as stated elsewhere: and by results from recent experiments which tend to confirm this view. 2—The dislocations in the diffuse boundary may be locked by impurity atoms at 300 °C and thus only sharpen the boundary at 400 °C with the aid of thermal vacancies. In this case it would be difficult to distinguish between the two sources of hardening (sharpening or jogging), using metal of this purity. Jack Washburn (author's reply)—The author wishes to thank Dr. Pratt for his discussion. In connection with his first comment, it should be pointed out that the temperature of testing in the present series of experiments was —196°C, whereas, in the earlier experiments he referred to,' it was 20°C. Therefore, the yield values should not be directly compared. It is likely that the crystals used in the present work were initially more perfect macroscopically than the large shear specimens used previously. The small size of the test section in the kink specimens made it possible to select regions of the large crystals, from which they were acid-cut, that were free of observable small angle boundaries. The sharpening of a microscopically diffuse boundary such as that in Fig. 15 begins in zinc of this purity well below 300°C. However, it is probably not justified to conclude that because a boundary looks sharp under the microscope it has attained the ideal structure. The author agrees with Dr. Pratt that jogging of dislocation lines is one of the structural features of a small angle boundary that should be important in determining its strengthening effect. More detailed information concerning the changes in boundary structure as a

Jan 1, 1956

This paper describes the operation involved in the sinking of a concrete-lined elliptical-shaped shaft at North Broken Hill Limited.Major factors such as geological features, future ventilation, ore haulage at depth and their relation to the location and selection of the type of shaft are described.Features covered in the sinking of the shaft include equipment details, with special reference to mechanical mucking, operational cycles based on time study analyses for sinking, concreting and the placing of steel sets. Safety precaution and statistical data is alsoincluded.INTRODUCTIONDue to the northerly pitch of the ore bodies in North Broken Hill Limited leases at approximately 42°, and the deepening of the active mining zone, it became apparent that No. 2 Shaft, the main operating shaft, would become unsuitable for the extraction of ore from the lower levels.Another major problem was the ventilation of the lower levels, and it was evident, that to ventilate efficiently these, and deeper levels, another upcast ventilation system would be required.Consideration was given therefore to the following: 1. Sink No. 2 Shaft from the existing bottom at 2770 ft. to 4200 ft., or Sink an internal shaft from the 2600 ft. level approximately 1000 ft. N. of No. 2 Shaft.2. Sink a new haulage and downcast shaft from the surface.3. Sink a new upcast ventilation shaft from the surface.It had been suspected that the ore bodies might flatten or even undergo a pitch reversal before reaching the...

Jan 1, 1956

By C. E. Armantrout, J. A. Rowland, D. F. Walsh

THE close-packed-hexagonal structure of mag-J- nesium is converted to a ductile and malleable body-centered-cubic lattice by the addition of lithium in excess of 10 pct. Further, the density of magnesium or magnesium-base alloys is decreased by additions of lithium. The practical possibilities of such alloys as a basis for uniquely light, malleable, and ductile structural materials were pointed out by Dean in 1944' and by Hume-Rothery in 1945.2 It was apparent to these investigators, however, that more complex compositions would be required if strengths sufficient for structural applications were to be developed in these alloys. In a search for strengthening additions, various investigators w have examined a number of the ternary and more complex alloys containing magnesium and lithium. An investigation of the fundamental characteristics of these alloys was undertaken by the Bureau of Mines. The investigation was initiated with a study of the magnesium-rich corner of the equilibrium diagram for the ternary system, Mg-Li-Al. The following data from published investigations of Mg-Li-A1 alloys were available: 1—a description of isothermal sections at 20" and 400°C through the Mg-Li-A1 constitution diagram by F. I. Shamrai;' 2—a diagram by P. D. Frost et al." showing approximate phase relationships at 700°F for a number of the Mg-Li-A1 alloys; and 3—diagrams showing the constitution at 500" and 700°F for the Mg-Li-A1 alloy system published by A. Jones et al.' Where compositions and temperatures permit comparison, these diagrams show disagreement. The 700°F isotherms of Frost and Jones differ only in the placement of the phase boundaries. But Sham-rai's 400°C (752°F) isotherm shows a variation in phases as well as in phase boundaries. Although rigid comparison of these different isothermal sections might not be justifiable, it seems impossible to reconcile Shamrai's construction with the isotherms of Frost or Jones. The isothermal sections presented in this paper were prepared to determine compositions which might be suitable for age hardening and to develop the general slope and placement of the various phase boundaries in the magnesium-rich corner of the diagram. Sections at 375", 200°, and 100°C were selected for investigation. In constructing these sections, the solubility of aluminum in magnesium, as reported by W. L. Fink and L. A. Willey Vn 1948, was used at the binary Mg-A1 boundary and the solubility of lithium in magnesium was obtained from the equilibrium diagram for that system as reported by G. F. Sager and B. J. Nelson" in the same year. The solubility of magnesium in lithium was determined experimentally and conforms in general to data reported by P. Saldau and F. Shamrai." Parameters for AlLi and MgI7A1, were taken from American Society for Testing Materials X-ray diffraction data cards. Experimental Procedures Although the isothermal sections presented in this paper are not unusually complex, the experimental techniques involved in their construction are made extremely difficult by the relatively high vapor pressure of lithium and the great chemical activity of both magnesium and lithium. Because of these characteristics, which make precise control of the composition of equilibrium-treated filings practically impossible, the disappearing phase method was used in preference to the parametric method in conjunction with metallographic studies. The alloys used in this investigation were melted and cast in an atmosphere of helium using a tilting-type furnace which enclosed a steel crucible and mold in a single unit. Each portion of the charge (500 to 600 g) was cleaned carefully just before placing it in the crucible; and the charge, crucible, and entire melting apparatus were evacuated and then washed with grade A helium while preheating to approximately 100°C. The alloys were melted and chill cast in an atmosphere of helium. Alloys prepared in this way were relatively free from inclusions and a fluxing treatment was considered unnecessary. The cylindrical ingots obtained were scalped and then reduced 96 pct in area by direct extrusion, yielding % in. diam rod. Sections of the rod, approximately 3 in. long, were given equilibrium heat treatments and then sampled for metallographic examination, X-ray diffraction study, and chemical analysis. The surface of each equilibrium-treated rod was machined to a depth sufficient to insure removal of contaminated material before samples for chemical analysis or X-ray diffraction study were obtained, and all decisions on microstructure were based on the examination of the central portion of the metallographic specimen. All specimens homogenized at 375°C were analyzed after this equilibrium heat treatment. When the composition of an alloy placed it in a critical area of the 200" or 100°C isothermal section, a check chemical analysis was made on a sample taken from the alloy specimen as-heat-treated at the particular temperature. Standard chemical procedures of gravimetric analysis were used in the determination of magnesium and aluminum; lithium, potassium, and sodium were determined by flame photometer methods

Jan 1, 1956

By A. M. Gaudin, D. W. Fuerstenau

IN concentration of certain ores by soap flotation, prevention of quartz flotation is desired; the contrary is true in treatment of some oxide iron ores. Experimental study of the flotation of quartz goes back at least a quarter of a century.' Clean quartz does not float with fatty acids or soaps but does float when activated by one of many metallic salts. Control of pH is important. Broadly speaking the problem of quartz flotation has been approached from the empirical side, as was the related topic of flocculation or dispersion of quartz suspensions? Empirical studies indicated the existence of critical relationships between the additions of collector and activator. These additions were not stoichiometric for the formation of soaps of the activator cation. For example, Gaudin and Rizo-Patrona found optimum quartz flotation at pH 10.6 using barium activation and oleate collection when the molar ratio of oleate to barium was 1 to 1 instead of 2 to 1, as would be called for formation of Ba(OL),. Cooke and Digre" ' found that if calcium is the activator, a minimum quantity of that agent is required for effective flotation when the pH is 11.5. In other words, if the concentration of Na' exceeds 10 -2.5 mols per liter or if the concentration of H exceeds 10-11 mols per liter, the concentration of Ca++ in solution required for quartz activation is increased. This suggests that H+ is much more effective than Na+ on 10-2.5 quartz, perhaps in the ratio ofp or 108. Schuh- mann and Prakash6 studied anew the activation of quartz by barium, calcium, aluminum, and ferric iron. Salts of these metals are activators provided they are in stoichiometric excess over the collector used with them. Alkaline-earth salts are effective only in alkaline circuits. Important as they are in giving data on the effect of various agents on quartz, all these studies fail to give information on the detailed structure of the quartz-solution interface. A beginning in this direction was made by Gaudin and Chang,? who measured the adsorption of radioactively marked barium and laurate ions at quartz surfaces, and by Gaudin. Spedden, and Laxen,8 ho measured the adsorption of radioactively marked sodium at quartz surfaces. Work has also been done by Bell0 n measurement of the adsorption of sodium ion and chloride ion at quartz-solution interfaces. In all these experimental measurements of adsorption, the solid was centrifuged or filtered from the bulk of the liquor with which it had been associated; and the composition of the solid surface was ascertained by analysis, after allowance was made for the ionic composition of the liquor included with the centrifuged solids on the assumption that it is identical to the bulk liquid. Adsorption measurements give only the total amount of collector adsorbed at the quartz-solution interface; they give no indication of the distribution of these adsorbed ions at the interfacial layer. It is the ionic structure of the solid-solution interface and its importance to flotation that is the subject of this paper. The structure of this interfacial layer can be investigated by means of electrokinetic methods so that by combining electrokinetic studies with adsorption measurements, a more complete picture of the quartz surface may be obtained. The following studies were made to ascertain how electrolytes used in the soap flotation

Jan 1, 1956

By D. J. Carney, E. Richard Randolph, E. Van Meter, J. J. Oravec, Stanley H. Ward, Gerald J. Anderson, Rolland L. 203-000-000-005 Blake

DURING the last 30 years the inductive electromagnetic method has been used chiefly in the search for massive sulphide mineralization. This application has met with varying degrees of success and in recent years has resulted in discovery of several large orebodies. Little has been written concerning its use in exploration for soft iron ores, but one of the present authors has reported on experiments with massive magnetic deposits.' To augment the exploration tools available to geologists in delineating iron orebodies, Cleveland-Cliffs Iron Co. and McPhar Geophysics Ltd. undertook in 1953 to apply the inductive electromagnetic method to Cleveland-Cliffs properties in the Lake Superior region. As a result of this project, equipment has been developed that enables simultaneous transmission of two audio frequency waves, and the field technique and interpretative procedure involved have furthered exploration in the district significantly. Thus far, inductive electromagnetic application in the Lake Superior region has been only a development tool, that is, it is used to locate obscured contacts and faults as a part of property expansion and development. However, its application to primary reconnaissance of unexplored areas may be feasible in the future. The method has assisted in placing drillholes efficiently, and the elimination of excess drilling foot-ages and/or actual elimination of unnecessary holes has amply justified the expense of the geophysical survey. Cost of the field work involved is comparable on a per station basis to the cost of a magnetometer or superdip survey. Since observations require no reduction, i.e., are directly interpretable, overall expenditure is low, and the scope and detail of the survey can be adjusted in the field as geological- geophysical correlation becomes evident. To a great extent, this eliminates the second-guessing so commonly arising after office calculations are completed on data obtained with other types of geophysical surveys. This unique feature of field interpretation and its associated intimate feel of the project area, is, perhaps, one of the most valuable aspects of the inductive electromagnetic method as applied to iron ore exploration. Basis of Method Fundamentally, the method involves transmission of an alternating electromagnetic wave, of a chosen audio frequency, which permeates the ground materials in the vicinity of a transmitting, or primary, coil, see Fig. 1. This wave, or field, induces an electric current in any conductor on which it is incident. The flow of an alternating current in a conductor sets up its own, or secondary, radiating electromagnetic field. These two fields form a resultant whose configuration depends on the following characteristics of the subsurface conductors: 1) size, 2) shape, 3) electrical conductivity, 4) magnetic permeability, and 5) frequency of the transmitted wave. To a lesser extent the resultant is also dependent on material adjacent to the conductor, topography, and surface conductivity. For illustrative purposes, the primary, secondary, and resultant fields may be represented by vectors. In operation, the direction of the resultant vector is measured by a small receiving coil tuned to the frequency of the transmitted wave. Generally speaking, the method can be compared to the transmission and reception of the familiar radio broadcast, with special variations permitting measurement of the effect on reception of intervening materials. Field Technique Mechanics of field operation are simple. The mast is set up in a vertical position and is then guyed in place. The transmitting loop then is raised by means of a sheave at the top of the mast and the coil connected to the motor-generator. A special plane table is clamped into position on the mast and the loop is plumbed. The plane table is oriented according to a grid system established over the project area. By means of this plane table it is possible

Jan 1, 1956

By K. B. Higbie

The quantitative separation of tantalum from columbium has been obtained through several liquid-liquid extraction processes. The valuable metals are separated by selective extraction from organic feed solution using a mineral acid or by selective extraction from aqueous feed solutions employing an organic solvent. The greatest degree of separation was obtained when organic ketones, particularly methyl isobutyl ketone, were used. Approximately 200 combinations of various organic solvents and mineral acids were tested as possible separation systems in which the tantalum or columbium content was extracted from organic solutions of the anhydrous pentachlorides.

Jan 1, 1956

By Y. C. Liu, W. R. Hibbard

An analysis of the relationship between the deformation and recrystallization textures in face-centered-cubic metals is presented. The analysis assumes that orientations of the secondary as well as the primary textures are related to the deformation texture. The effect of alloying elements on the recrystallization texture of copper-base alloys is also discussed. ROTATIONAL relationships based on prior orientations have been used to derive both the primary and secondary recrystallization textures."" This similarity suggests that, if the secondary texture arises from grains formed during primary recrystallization, as proposed by Dunn: and if primary recrystallization derives its lineage from the deformation structure, then the orientations obtained in secondary recrystallization .as well as those obtained in primary recrystallization should be related to the deformation texture. The following discussions are

Jan 1, 1956

By F. W. Wessel

This report summarizes Bureau of Mines laboratory tests of four tungsten¬-bearing materials of various grades, The test work has demonstrated that the dry reaction between sodium carbonate and scheelite is best conducted at 900° C. or a few degrees less. The sodium carbonate requirement, in addition to the stoichiometric equivalent of the scheelite, is in some inverse relationship to the grade of tungsten in the ore. Residence time and particle size exert a definite but minor control on the reaction. Pressure-digestion tests on an impure concentrate indicate the technical feasibility of extraction by this process. INTRDUCTION Over 100 years ago Oxland discovered that tungstic oxide could be removed from wolframite and converted to a soluble form by reacting the mineral with a soluble alkaline salt at elevated temperatures. He patented this discovery, and this patent 4/ since has been the basis for most tungsten extraction. Much literature exists on this process and its modifications, and the characteristics and possibilities of the reaction are quite well defined.

Jan 1, 1956

Jan 1, 1956

By W. E. Wickerham

THE Magnetic Storm Monitor is an instrument that continuously records variations in the earth's total magnetic field at a fixed location. It is intended for use in conjunction with airborne magnetometer surveys. There are stormy periods when changes in the earth's magnetic field are so violent that data obtained with airborne equipment would be of little value. The Monitor provides this information so that flights may be cancelled or terminated, thus eliminating useless flying. Moreover, when some unpredictable change in the earth's field occurs during an airborne survey, the Monitor record, showing a similar event, may serve to salvage the data. The utility of a base instrument is determined largely by its physical dimensions, power requirements, stability, and reliability. This instrument is small enough to be transported in any powered vehicle. It will operate from either a 110 v, 60 cycle power line or from an inverter powered by an automobile battery. The development of an electronic feedback circuit that measures the magnetic field strength and a fabricated buckout magnet having essentially zero temperature has contributed to instrument stability and reliability. A tripod supporting the magnetometer head, a chassis housing all electronic components, and an Esterline Angus Recorder comprise the equipment, shown in Fig. 1. The vibrator-type inverter shown is used when a 110 v, 60 cycle power line is inaccessible. Approxi- mately 60 w are required to operate the instrument and the circuit is insensitive to reasonable power line voltage changes or transients. The head unit contains a fluxgate-type magnetometer element and a special magnet mounted on a ceramic structure. Since this magnet is used to buck out most of the earth's field, adjustments are provided for properly positioning the magnet with respect to the element. This assembly is mounted in such a way that the element can be oriented into the total field. Fluxgate Element: The heart of the Storm Monitor is a fluxgate-type magnetometer element. The ability of this unit to detect changes in magnetic fields has been covered at length in the literature.1, 2 For this discussion it will suffice to say that the Gulf

Jan 1, 1956

By P. W. Neurath, R. E. Waite

INFORMATION is available on the effect of stress on permeability, coercive force, and hysteresis for a variety of materials' but for the technically important grain-oriented 3 pct Si-Fe' the stress effects are not adequately covered in the literature; in addition, most of the stress data do not permit estimation of what would happen to the 60 cycle watt losses of the material under stress. Direct measurement of these effects therefore has been made and appears to be of considerable theoretical as well as practical interest. Losses were measured on the central 25 cm portion of 40~3~0.035 cm samples which could be stressed in a small tensile machine built for this purpose. Under tension the following effects, illustrated in the figures by a particular example, were observed: 1—"Unstrained" material of commercially acceptable loss level shows no change or a small increase in loss at low elastic stresses. For the sample shown in the figures, this is illustrated during the initial run, where a 7 pct increase is observed (Fig. 1). 2—There is no additional change in loss when the sample is further strained up to the elastic limit (Fig. 1). Within that limit the loss-stress curve is reversible. This is not illustrated in Fig. 1. 3—Even in the plastic range only small increases in loss are observed as long as the sample is kept under stress (Fig. 2, point N); often no increase can be observed (Fig. 1). 4—A large increase in watt losses is observed after removal of the stress subsequent to plastic deformation (Figs. 1 and 2). 5—All, or nearly all, of the foregoing increase in loss due to plastic deformation can be eliminated by a reapplication of tensile stress but returns upon removal of this stress. This is illustrated in the third run (Fig. 3). This run remains within the elastic limit and shows the reversibility of the stress-loss curve under this condition. These findings have been confirmed on large Samples (approximately 200~10~0.035 cm and larger) except that under 1 no initial increase in loss was ever observed on these. The accuracy of the watt loss measurements is of the order of 1 pct. Neither bending of the sample in the tensioning device nor a redistribution of flux along the width of the sample accounts for these results. They therefore must be explained on the basis of either a change in the domain configuration due to stress or a change in the domain wall mobility. Acknowledgment The assistance of Mr. Robert L. TenBroeck with the instrumentation is gratefully acknowledged.

Jan 1, 1956