Search Documents

The primary purpose of the Institute is to advance the technologic and engineering arts embraced by it through interchange of knowledge This can best be done by the presentation and discussion of technical papers by its members Short practical papers are especially welcome An author should always satisfy himself that his material is of a quality that will be a credit to him and to the Institute The preparation of a good paper frequently leads to a reorientation of the author's thoughts, and publication contributes much to the professional standing of the author Members are urged to submit papers presenting the results of their work Attention to the following suggestions will greatly further the prompt and efficient handling of manuscripts

Jan 1, 1952

By A. W. Schlechten, Ernest J. Breton Jr.

Experiments on the separation of copper and zinc ions by selective action of ion exchange resins showed the carboxylic type to be more effective than the sulphonic resins. The latter demonstrated a greater capacity over a wider pH range. Data show the effectiveness of resins as a means of concentration. IN recent years the restrictions of stream pollution laws and the high price of metals have created an interest in ion exchange as a means for metal recovery. Some applications have proved successful. In Germany during World War 11, 17 tons of copper per day were recovered from rayon mill wastes by means of ion exchange resins;' and for some time in this country a large ion exchange unit has been in operation for the recovery of copper from rayon waste water. The possibilities of applying ion exchange to the recovery of metals occurring in plating rinse water is particularly promising. In most of these applications only the metal being recovered occurs in the waste. The ion exchange resins act merely as a means of concentrating the metals to a point where they can be recirculated. It would be highly desirable to use ion exchange as a means of not only concentrating but also of separating metals. With the exception of the impressive separations accomplished in connection with the atomic energy program, very little has been done on metal separations.' Therefore, an investigation was undertaken at the Missouri School of Mines and Metallurgy to determine if either of the two main types of ion exchange resins could be used to separate metal ions in solution. The selective removal of copper ions from a mixture of copper and zinc on carboxylic and sulphonic-type resins was investigated as a function of flow rate, pH, copper-zinc ratio, and concentration. It was shown that zinc can be separated from copper and that very large ratios of concentration can be obtained using ion exchange resins. Since ion exchange is relatively new to the field of metallurgy, a brief review of the subject will be included. Theory of Ion Exchange A comprehensive theory for ion exchange has not been developed as yet, but the mechanisms are analogous to metathetical reactions: R Na + Cu++ *=? K(SO3)2 Cu + 2Na+ R is the designation for the ion exchange resin. If a copper solution is passed over a resin bed in the sodium form, two ions of sodium will be released for every ion of copper removed. For the most part this reaction follows the laws of mass action and of electrical neutrality. Consequently, if an excess of sodium ions is passed over a bed containing copper, the reactions will be reversed, and the resin will be regenerated to its original form. A few empirical rules governing the exchange reaction have been set forth: 1—In general ions with a high valence will replace ions with a lower valence. 2—Ions having higher activity coefficients have a higher replacement potential. 3—In a series of mono-valent ions, those with the smallest radii of hydra-tion will tend to replace those having larger radii of hydration. 4—Where ions are similar in most respects, those with the higher atomic weight sometimes will take precedence. This last rule is not as definite as some of the others. These rules apply to rather dilute solutions at moderate temperatures and assume all ions to be present in about equal concentrations. Higher concentrations and temperatures may in some cases reverse the normal exchange reactions. Ion exchange materials are unique in that their efficiency increases as the concentration of the solution decreases. For many exchangers, most efficient operation is obtained at concentrations in the order of one thousandths of a percent. Most applications, though, are made in solutions containing considerably higher concentrations than this. Coste9 as shown that ion exchange resins will remove aluminum and iron effectively' from solutions of up to 10 pct chromic acid. Ion Exchange Resins Ion exchange resins are insoluble, porous, resinous structures to which active groups have been attached. Active groups such as (—SO,,)- and (COO)- pick up cations; hence structures saturated with groups such as these are called cation exchangers. Structures saturated with groups such as (—NH,)' which pick up anions, are referred to as anion exchangers. The resinous structure of necessity is resistant to strong acids, bases, oxidizing, and reducing agents, and most of the common organic solvents. An idea of the stability can be gaged from the fact that resins last for many years under constant use without detectable chemical or physical breakdown. The ion exchange reaction is not confined to the surface of these synthetic resins. Its porous structure permits active groups in the center of a particle as well as those on the surface to remove ions. A high capacity resin such as Amberlite IR-120 will remove up to 3.3 lb Cu per cu ft of resin. In this investigation several approaches to the problem of separating copper from zinc by ion exchange were considered. First, if a reagent could be found which would complex one of these metals and not the other, then by passing this reagent through a bed of exchanger containing copper and zinc, the

Jan 1, 1952

Los Angeles may well be host to one of the most historic gatherings of AIME members Feb. 16 to 19, 1953, when the 175th General Meeting is scheduled to take place. Plans in the formulative stage indicate that the meeting will be one of the largest ever held by AIME. Headquarters will be the Hotel Statler, now nearing completion of construction. The hotel will be one of the most modern hostelries of the century. The first technical session, of which there will be more than 75, will take place Monday, February 16. Mineral Industries Education Div. and the Board of Directors meet Sunday, February 15. Sessions will end with a meeting of the Council of Section Delegates on Thursday. Deadline for papers that may be preprinted for presentation at the meeting is Sept. 15, 1952. However, division program committees may list papers for presentation after that date if they choose. Various committees are engaged in formulating final plans for the meeting. Developments will be announced as progress is made.

Jan 1, 1952

By W. R. Johnson, M. Hansen, John M. Parks

AS part of a research project sponsored by the Signal Corps Engineering Laboratories, which had the objective of obtaining a magnet wire of good conductivity and low temperature coefficient of resistance, a comprehensive literature survey, supplemented by experimental work, revealed that a linear relationship exists for solid-solution alloys between the electrical conductivity, K, and the temperature coefficient, a, as expressed by the equation: k = a/ß where ß is constant for the solvent metal and a - per°C. tR0 It has long been known that the electrical conductivity at a given temperature and the temperature coefficient of resistance of binary alloys are related to their constitution by the LeChatelier-Guertler rules, as illustrated by Figs. 1 and 2: Rule 1—In alloy systems consisting of a heterogeneous mixture of two phases, the electrical conductivity and temperature coefficient vary as a straight line, if the composition of the alloys is given in volume percentage, Fig. 1. Rule 2—In solid solutions, the electrical conductivity and temperature coefficient are always lower than those of the solvent metal, and usually a considerable decrease occurs with the first small percentage additions of the solute metal, Fig. 2b. If the two components form a continuous series of solid solutions, the electrical conductivity and temperature coefficient curves take the form of a U-curve, Fig. 2a. That some kind of proportionality exists between electrical conductivity and temperature coefficient of resistance is implied by the LeChatelier-Guertler rules and by study of data such as those given by Smith and Palmer,' Fig. 3. Dellinger2 in 1910 first recognized this relationship in a number of commercial copper wires, ranging in conductivity from 94 to 100.7 pct I.A.C.S. He gave the ratio of temperature coefficient to the percentage of conductivity as a constant, C = 0.003939. A year later, Lindeck observed that the linear relationship was valid for a wider range of conductivity in "various sorts of copper," and concluded that the product of resistivity and temperature coefficient was 6.78x10-5 1.5 pct. Since then, this relationship seems to have been entirely ignored. Conductivity-Temperature Coefficient Relationship If the electrical conductivity of copper solid-solution alloys with phosphorus, silicon, arsenic, antimony, aluminum, nickel, manganese, and iron is plotted against the temperature coefficient of these alloys, the diagrams in Figs. 4 and 5 are obtained. Similar data were found with copper-rich solid solutions containing magnesium, cobalt, and titanium,'" as shown in Fig. 6. In all cases, a linear relationship exists. The point representing the highest

Jan 1, 1952

By G. S. Hume

"THERE HAS BEEN a marked growth in the petroleum industry in Canada since the end of the war. The rate of growth in the demand for oil products has exceeded that in United States, although the per capita consumption is still less. Estimates of the consumption of petroleum and petroleum products in Canada in 1951 are approximately 154,000,000 barrels, which is slightly more than 11 •barrels per capita, whereas the estimated consumption in United States for the same period, according to World Petroleum, is placed at 2,619,- 970,000 barrels. This, on the basis of a population of 154,000,000, would be equivalent to 17 barrels per capita. The increase in consumption of the petroleum and products is world wide. World production in 1951 has been estimated (Oil and Gas Journal) at 11,700,000 barrels a day or more than 41;4, billion barrels for the year. United States production increased 13.7 per cent to 6,143,000 •barrels a day and Canada'.s ,, total production increased about 65 per cent from a total of 29,091,235 •barrels in 1950 to an estimated (Dominion Bureau of Statistics) 48,096,800 barrels in 1951.The trend to use increased amounts of petroleum and petroleum products, particularly in the United States and Canada, has also been supplemented by increased use of natural gas. The rate of expansion of the consumption of natural gas in United States in the past few years has been very rapid, increasing from 2,600 billion cubic feet in 1940 to 5,975 billion in 1950, with the proven reserves in the same period increasing from 85,000 billion to 186,000 billion cubic feet."

Jan 1, 1952

THE Howe Memorial Lecture, in memory of Henry Marion Howe, Past President of the Institute, was authorized in April, 1923, as an annual address to be delivered by invitation under the auspices of the Institute by an individual of recognized and outstanding attainment in the science and practice of iron and steel metallurgy or metallography, chosen by the Board of Directors upon recommendation of the Iron and Steel Division The following were the Howe lectures and lecturers for the years indicated 1924 What is Steel? By Albert Sauveur 1925 Austenite and Austenitic Steels By John A Mathews 1926 Twenty-five Years of Metallography By William Campbell

Jan 1, 1952

By L. E. Djingheuzian

"IntroductionIN 1940, in a series of articles, M. W. von Bernewitz(l) reviewed in detail roasting of gold and silver sulphide ores and concentrates. Since that time some significant developments in roasting have taken place, and a number of papers have appeared in the Canadian technical literature, dealing severally with the roasting of a particular ore or concentrate.The purpose of this paper is not only to review some of these Canadian papers and bring the information on Canadian roasting practices to .date, but also to analyse the mechanism of roasting. Hence, it is proposed to start with a study of physico-cl1emical factors fundamental in roasting, the knowledge of which, by creating a sound basis for a proper roaster design, makes good roasting possible.Physico-Chemical FactorsRoasting can be defined as heating sulphide ores in presence of air below fusion points of the constituent minerals, at such temperatures as to convert metallic sulphides to oxides. Hence, roasting is a chemical process.The object of roasting is, by changing, chemically, mineral constituents of sulphide ores, to make the economic recovery of the desired •Constituent metal by a subsequent standard treatment possible. For instance, pyritic ores, containing gold in sub-microscopic form which no amount of grinding would release, are roasted in order, by oxidizing the sulphides, to open up their structures to such an extent as to enable cyanide solutions to come into contact with the gold and dissolve it. The production of porous calcine is, therefore, the object of roasting of refractory auriferous sulphide ores or concentrates. Such a porous calcine may be defined as a desirable calcine, and the roasts which produce desirable calcines can in their turn be termed desirable roasts."

Jan 1, 1952

By F. E. Steigert, A. H. Geisler

THE permanent magnet alloy comol, which contains 17 pct Mo, 12 pct Co, balance Fe, exhibits a precipitation reaction analogous to that at the iron end of the binary Fe-Mo system. The equilibrium precipitate, (P,), has a structure isomorphous with Fe,Mo, which is rhombohedra1 with parameters a = 8.97A and a = 3038.6&apos; according to the work of Arnfelt and Westgren.&apos; In the ternary alloy the parameters are a = 8.87A and a = 31°0.5&apos;. Oscillating crystal patterns of a single matrix crystal, M, in which P, was precipitated by slow cooling from 1300°C, showed that the orientation relationship of the two lattices is as follows: (110)P3 // (110)* (111)p3 // (110)m There are crystallites of P, in 12 different orientations in a single crystal of the parent solid solution. Microscopic examination shows that the crystallites are generally plate-like with their lateral dimensions parallel to (110) matrix planes. When precipitation in a supersaturated alloy quenched from 1300°C progressed isothermally at temperatures between 600" to 800°C, the evolution of the P, structure could be traced. Diffuse diffraction effects in Laue patterns provided early evidence of the precipitation process. Analyses of these by a previously described technique2 showed that they corresponded to rod-like elements parallel to <110> matrix directions in reciprocal space. With further aging to promote growth of the precipitate, the rod-like elements contracted to points in reciprocal space for normal Bragg reflection from the precipitate as shown by the left diagram in Fig. 1. Thus the diffuse scattering was attributed to the small thickness of the plate-like particles which was inadequate for sharp diffraction. When the precipitate particles were first thick enough to give normal diffraction their structure was different from that of the equilibrium precipitate, P,. The first structure, P1, presumably is a coherent transition struc-

Jan 1, 1952

PRESIDENT Mrs Oliver Bowles 5000 Massachusetts Ave N W Washington 16, D. C FIRST VICE-PRESIDENT Mrs David Eugene Park 350 East 57th Street New York 22, N Y. SECOND VICE-PRESIDENT Mrs A B. Kinzel 320 Park Avenue New York 22. N. Y

Jan 1, 1952

Manganese deposits discovered in Maine may solve one of the problems facing the steel industry today. Diamond drilling is scheduled to start in Aroostook County to determine whether the ore is of acceptable grade. The Bureau of Mines estimates the deposit contains several hundred million tons. If true, it means about a 30-year supply. The steel industry presently imports about 90 pct of its needs. Noranda Mines, Ltd., is planning a sulphur-iron plent for Ontario&apos;s Niagara Peninsula. Although contracts have not been signed, a substantial agreement has been reached with American Cyanamid, Ltd., whereby the Noranda plant would be constructed adjacent to Cyanamid&apos;s chemical plant at an estimated cost of million. The unit would treat approximately 100,000 tons of pyrite concentrate annually. San Manuel Copper Corp., wholly-owned subsidiary of Magma Copper Co., is asking the RFC for a $111.28 million loan for development of a copper orebody in Pinal County, Ariz. The property s said to be capable of producing 10 million tons of ore annually. San Manuel plans to construct facilities for processing 30,000 tons of ore and for smelting 800 tons of concentrate daily. An Aeromagnetic map covering 120 sq miles of the Wichita Mountain area in southwestern Oklahoma indicates a possibility of iron production from titaniferous magnetite deposits of the Raggedy Mountains, northwest of Lawton. The map shows an area in the north central part of the region which may prove favorable to further development.

Jan 1, 1952

By N. J. Grant, W. R. Opie

THE amount of hydrogen that will dissolve in lead has been considered negligible. However, a limited number of measurements made recently using apparatus built for determining hydrogen solubility in aluminum alloys&apos; indicate that liquid lead will hold a small but appreciable amount of hydrogen in solution. The apparatus used was similar to that developed by Sieverts.&apos; This consists of a bulb to hold the molten metal, a gas burette for introducing a measured quantity of gas into the bulb and a manometer for measuring the gas pressure in the bulb. Measurements are made by introducing enough of an insoluble gas (helium) to fill the system at a given temperature and pressure, thereby determining the hot volume of the bulb. This gas then is pumped out and hydrogen is introduced until the same pressure is reached, the metal being maintained at the same temperature while in contact with each gas. The difference between the volumes corrected for pressure is then the hydrogen solubility. A more detailed account of the procedure can be found in refs. 1 and 2. The lead was melted in an alundum crucible by induction heating to provide uniform temperature and an important stirring effect. The metal was the purest obtainable, 99.999 + , prepared especially by the research department of the American Smelting and Refining Co. Measurements were made by approaching the equilibrium value from high and low temperatures during the constant pressure runs, and from high and low pressures when the temperature was held constant. Thus a number of measurements were made on each of two large samples which weighed 336 and 398 g. The gases were purified as .described in ref. 1. The effect of temperature on the solubility was studied with the pressure held constant at 760 mm of Hg. To show the effect of pressure, solubility measurements were taken at two constant temperatures, 600" and 900°C. Results The effect of temperature on hydrogen solubility is shown in Fig. 1. The curve representing the data is parabolic, as are plots of hydrogen solubility vs. temperature for other metals and alloys (aluminum,&apos; copper," and iron,& for example). Fig. 2 shows the relationship that exists when the solubility is

Jan 1, 1952

THE following employment items are made available to AIME members on a nonprofit basis by the Engineering Societies Personnel Service, Inc., operating in cooperation with the Four Founder Societies. Local offices of the Personnel Service are at 8 W. 40th St., New York 18; 100 Farnsworth Ave., Detroit; 57 Post St., San Francisco; 84 E. Randolph St., Chicago 1. Applicants should address all mail to the proper key numbers in care of the New York office and include 6c in stamps for forwarding and returning application. The applicant agrees, if placed in a position by means of the Service, to pay the placement fee listed by the Service. AIME members may secure a weekly bulletin of positions available for $3.50 a quarter, $12 a year. MEN AVAILABLE Project Manager or Construction Engineer, 48, married. Twenty-five years&apos; experience on mine, mill and smelter construction work, design and operation, U. S. and Mexico. Speak Spanish. Now employed; available 30 days notice. Prefer U. S. or Mexico. M-698-489-E-1-San Francisco. Mining Geologist, 53, single. Eleven years&apos; intensive field experience giving a completely practical competence for the smallest or largest of areas; plus the highest possible grade of academic background and independent research qualifying for top rating. Available in thirty days or less. Any location acceptable. M-699-3611-E-7-San Francisco.

Jan 1, 1952

By W. B. Dingle

"IntroductionMANY PAPERS presented on developments in the Canadian Petroleum Industry •during the past few years have commenced with this general sentence: ""The past year has been a record •one for the oil industry in Canada, with new records being set in nearly all phases •of exploration and development ,activity"". This sentence applies equally well to 1951. It is not possible to outline all the details of the broken records in exploration, development, and production but general comparisons can be made. There are several significant developments that have stolen the spotlight during 1951, some of which were foreseen in 1950 and some which were not. Among the high-lights were the following:(1) The greatly •expanded activity in the search for gas, which was touched off by the new Alberta regulations covering gas leases and reservations.(2) The discovery of commercial oil production in the Williston basin of North Dakota and Manitoba, which will have far reaching effects on Canadian oil.(3) The greatly increased activity in northern Alberta, northwestern British Columbia, the southern Northwest Territories, Saskatchewan, and Manitoba.(4) The new discoveries in the general central Alberta area.(5) The granting •of a permit for an oil pipeline to the Pacific coast.(6) The arrival of Western Canadian crude in central Ontario.(7) The number of new refineries completed, commenced, or proposed.(8) The present •and proposed expansion in the petrochemical industry.Most of the remarks made on various exploration and development •activities will refer to Western Canada operations, primarily because the greatest •activity and the most significant developments have been there. Eastern Canada exploration and development operations were at a slightly higher level than in 1950."

Jan 1, 1952

CONTENTSIntroductionGeneral GeologyCoral Reef-Volcanic Set&apos;iesRock TypesMicaceous Sandstone and MudstoneLimestoneVolcanic RocksChertsDepositionDiatremesEarth MovementsRelation of Ore Bodies to StructureINTRODUCTIONThe author encountered the problems discussed in this paper in 1947 while surveying the mining centres of Mungana and Redcap for Broken Hill South Ltd. After his resignation from that company he made a semi-regional survey to investigate the regional problems raised by the preliminary study. Broken Hill South Ltd. continued its studies on the known ore bodies while the author&apos;s investigation was going on, and he is indebted to the staff of this company for assistance during his field work.The area mapped is part of a larger area mapped in reconnaissance by the Aerial, Geological and Geophysical Survey of Northern Australia by a party headed by Dr. H. I. Jensen...

Jan 1, 1952

By K. V. Lindell

THE 70-mile serpentine belt of eastern Quebec, producing 70 pct of the world&apos;s chrysotile, has 11 operating mines, two of which are underground, eight are open-pit, and one is both open-pit and underground. The combined operation, the Jeffrey mine, of the Canadian Johns-Manville Co., Ltd. is the largest producer in the group. Haulage All four of the separate operations falling under transportation at the Johns-Manville Jeffery Mine at Asbestos, P. Q., is handled by the company owned Asbestos and Danville Railway. A variety of equipment is operated over the 25 miles standard gage railway. Included in the scope of transportation are: 1-Hauling mill rock to the mill. 2-Hauling stripping and waste rock to the waste dump. 3-Hauling mill tailings to the tailings dump. 4-Hauling supplies from, and finished products to Danville. Main line tracks are permanent, but those within the pit and on the dumps have to be relocated constantly to follow the mining face and dump edges. Tracks within rock areas in the mine are laid on steel ties and can be moved by a bulldozer. Standard mechanical track shifters move tracks in dirt areas in the mine and on the dumps. Train-movements, both within the mine and over the out-lying tracks are controlled by a dispatcher located at the southwest rim of the pit. Steam locomotives haul all stripping, waste rock, and ore from the mine to the gathering yard at the northwest rim of the pit. Normally, two trains per operating shovel are used, with adjustment for optimum loading. In the event of shovel loading on the bottom level or in good stripping, service may be increased to three or four trains per shovel. From the gathering yard a 100 ton diesel-electric locomotive hauls the mill rock to the mill slips, a distance of about three miles. Electric or steam locomotives haul the waste rock and stripping to the waste dump located about two and one-half miles from the mine. Stripping cars are sprayed with a chloride solution and "gravelled" to prevent wet stripping from freezing in the cars during the cold months. Cars pass under a shaking screen which distributes an even

Jan 1, 1952

By W. M. Goodwin

"IntroductionIN THE preceding paper we have learned about Canada's resources of metallurgical coal. There is an adequate amount in Nova Scotia, a very large reserve on the eastern flank of the Rocky mountains, and a strictly limited supply on the Pacific coast. Added to these is an unknown quantity of coking coal in the Peace River district, at present rather isolated but possibly capable of industrial development in the future.The chief use of metallurgical coal is to make iron and steel. For this, an adequate supply of iron ore is required. So we should now scan the Canadian supply of iron ore, the possibility of its increasing use at home, and the probable markets abroad.Trade in iron ore tends to be international, as is the case with many other raw materials. The present tendency with iron and steel, in contrast, is to keep its manufacture within national boundaries, and there is no evidence that this will change much in the years to come. We should keep these two points clearly in mind when considering the disposal of iron ore from Canadian mines. We should remember, also, that the modern blast furnace and steel plant has such a large output that a correspondingly large population, reasonably compact, is needed to consume its products.Large Ore Supply in East, Small in WestCanada has now four major iron ore fields, well situated to serve adequately the eastern half of the country. Wabana .and Labrador are well placed to serve overseas markets and plants on the eastern seaboard and eastern interior of the United States and Canada."

Jan 1, 1952

By D. S. Sanders, E. W. Witcomb

FLOTATION tests, from which the flowsheet for the concentrator was determined, were made in a pilot mill at Chuquicamata and later comparative testing of full size flotation cells was done at the Andes Copper Mining Co. concentrator in Potrerillos. The principal sulphide copper mineral is chalcocite with varying amounts of covellite, enargite, and chalcopyrite. The oxidized portion is principally antlerite, a green basic copper sulphate. The gangue minerals include quartz, sericite, pyrite, feldspars and kaolin. Chuquicamata pit ores have proved to be hard grinding. The results of the flotation and metallurgical work prove that good extraction and concentrate grade can be obtained under a rather wide range of conditions. Metallurgy In general the metallurgy of the ore requires a fairly close control of the grind to the primary rougher flotation and of the regrind of the primary rougher concentrate before cleaning. Regrinding is necessary to reduce the insoluble content of the final concentrate since a large part of the middling combinations are between the copper and silica minerals. The alkalinity of the pulps can vary between wide limits and control of the percent solids gives the desired grind. Alkalinity Control Arroyo Salado water is supplied to the concentrator head tanks. It contains about 5000 ppm of salts but test work shows no deleterious effect. Actually this water permits a decrease of as much as 1 lb of lime per ton of ore as compared to San Pedro water, which is used for leaching oxide ore. About one quarter of the water flow through the concentrator will be new water from the reservoir. The remainder will be reclaimed from the thickeners. For primary grinding and rougher flotation, new and reclaimed water are combined in the head tanks. To avoid erratic results, only new water is used in the regrind system. Milk of lime is added to the rod mill feed chute to obtain the maximum benefit of mixing with the ore. This protects the equipment from corrosion due to entrained acids and soluble copper salts. Lime consumption is 3 to 5 lb per ton of ore. Grinding and Flotation The six bin gates over each belt feeder are opened in controlled combination and sequence to keep a live bed of ore in the bin to prevent arching and to obtain mixing. The milk of lime added ahead of the rod mill is regulated to suit rougher flotation requirements. The primary promoter reagent, Aerofloat 238, is added to the 10-mesh discharge of the rod mill as it is laundered to the ball mill scoop box. The classifier overflow is regulated to produce a grind of about 12 to 15 pct +65 mesh and 60 pct -200 mesh. A secondary promoter Z-4 (aml zanthate) and the pine oil frother are added in the overflow launder where a pH of 10 to 11 is maintained. Comparatively heavy beds of froth on the

Jan 1, 1952

By Robert Glass Cleland

BECAUSE of the country&apos;s vast mineral resources, Alexander Von Humboldt, the great German scientist who visited Mexico, or the Kingdom of New Spain, a hundred and fifty years ago, very aptly called that country the "Treasure Chest of the World." During the three centuries of Spanish rule, mining was the principal industry of the kingdom, the largest contributor to the country&apos;s prosperity, the chief common denominator in Mexican economic life. Public revenues and private fortunes, employment and markets, agriculture and trade, charities and churches, the incentive for frontier settlement and exploration, and the funds for outfitting the expedition of colonizer and conquistador-all were dependent upon the streams of precious metals that flowed century after century from the mines of Guanajuato, Zacatecas, Real del Monte, San Luis Potosi, and scores of other minería that lay scattered everywhere throughout the land. Sonora, one of the oldest and most renowned of the frontier provinces of New Spain, had been the scene of a hundred rich strikes, sudden stampedes, and widely heralded bonanzas long before the famous and frenzied Gold Rush

Jan 1, 1952

The importance, validity, and acceptability of the Paley Report has become the great issue of the minerals industry. A 12-man panel made up of representatives of various facets of the industry sat down at the 1952 Mining Congress Show in Denver in an attempt to clarify the many opinions currently held concerning the report. Howard Young, deputy administrator of the Defense Materials Procurement Administration, noted that the report had caused more discussion and serious thinking than any other government report, He did not subscribe to the "have not" principle, however, but called it a "need more" principle. Horace M. Allbright, president of U. S. Potash Corp., believes industry should continue to develop the report. He cited the editorial appearing in the September, 1952 edition of Bining Engineering,,, "Don&apos;t Let It Die," as expressing his feelings. Edward Snyder, president of Combined Metals Reduction Corp., says the statistics used in the report were used to promote a false international policy. He sees the report as a master plan for the development of the superstate. He also stated that the-ore reserves given in the Pales, report represent only 10 pct of what is actually available.

Jan 1, 1952

By J. K. Kerver, J. S. Osoba, J. G. Richardson, J. A. Hafford

A detailed study of a number of methods of relative permea-abilitv measurement has been made in a search for the tech-niqrle most suited to routine analysis of cores taken from reservoir rock. It has been found from tests run on the same samples of core material by a number of techniques that the Penn State, Hassler, Hafford, and dispersed feed techniques all yield results which are felt to be reliable. Conditions under which the faster single core dynamic technique may be used are described. Further work on the calculation of relative permeabilities to oil from data obtained by the gas drive method is needed before this latter rapid method can be utilized. Correlations between theoretical studies and experimental results have been obtained in studies of the boundary effect. pressure distribution in two-phase flow, and gas expansion effects. Previous conclusions that the effects of the outflow boundary could be made negligibly small have been substantiated. Results of experimentally determined oil and gas pressure distributions along a core sample during flow are presented. Further studies of the effects of rate of flow in the measurement of relative permeability-saturation relations have shown that results are independent of the rate of flow as long as the flow rate is below the point where inertial effects commence. An analysis of the effects of a severalfold expansion of gas along the flow path indicates that while saturation gradients are induced in the test sample, the errors caused by this phenomenon in relative permeability measurements are small. INTRODUCTION Many pages of literature have been devoted to pointing out the need for relative permeability-saturation relations in reservoir engineering. One of the most attractive ways of obtaining this information is by the analysis of samples of core material taken from the formation in question, and again literature has described man); methods for obtaining these data. It is the purpose of this paper to present the work that has been done in the study of some of these published methods together with some other methods that have been recently developed in this laboratory. Also, a study of some of the factors that influence the laburatory determination of relative permeability-saturation relations is presented. FACTORS WHICH AFFECT LABORATORY STUDY OF FLUID FLOW THROUGH RESERVOIR ROCK To determine relative permeability-saturation relations of samples of reservoir rock in the laboratory, it is important to know what factors affect these measurements in order that the magnitude of these effects can be ascertained and steps then can be taken to eliminate or, in some cases, to minimize them. The factors that have been investigated are the boundary effect, the effect of gas expansion. and the rate effect. Boundary Effect In laboratory experiments in which two immiscible fluids are flowed through a porous medium, there exists a discontinuity of capillary properties at the outflow face. This discontinuity exists became the fluids pass from a region of finite capillary pressure in the sample to a region of zero capillary pressure in an open receiving vessel. The capillary forces existing in the core caupe the rock to tend to retain

Jan 1, 1952