Search Documents

By James A. McGurty, Walter J. Koshuba, Samuel G. Gordon, Gilbert E. Klein

ONE of the problems encountered in working with metals at elevated temperatures is the instability resulting from solid-solid diffusion at a -common interface. A determination of the nature and magnitude of this phenomenon is important as related to structural properties of materials potentially useful in high temperature applications. This paper is concerned with the solid state reaction between metallic molybdenum and beryllium at elevated temperatures. In the older literature,' there were no known inter-metallic compounds in the system Be-Mo, and the list of beryllium intermetallics was rather small. New compilations have been made by Smithells' and by Taylor," listing all the then known beryllium binary intermetallic compounds. In addition to these, some new phases have just been reported' in the system Zr-Be and some further compounds of the type MBe,3 have been currently described. The new compound MoBe,, which is reported upon in this paper differs considerably from the above mentioned MBe13 group, and will be discussed in detail. Diffusion Study The nature of the solid diffusion at a Mo-Be interface was determined by sealing a beryllium rod inside a molybdenum capsule and heating at a temperature of 2000°F' (1100°C) for 100 hr. The molybdenum capsule was fabricated from % in. swaged molybdenum rod obtained from the Fansteel Metallurgical Corp. The beryllium metal was obtained from Brush Beryllium Corp. as % in. cold-drawn rod. This material assayed 99.05 pct Be and contained as impurities 0.84 pct Be0 and 0.19 pct Be2C. The molybdenum capsule was % in. in OD x 2 in. long. To prepare it, a concentric hole 0.250 in. + 0.001 in. — 0.000 in. in diam was drilled and reamed in one end of a rod to a depth of 1 '/2 in. A 1 in. long beryllium rod 0.250 in. + 0.000 in. — 0.001 in. in diam was pressed into the molybdenum capsule. A molybdenum plug 0.250 in. & 0.001 in. in diam x 9/16 in. long was then used to seal the beryllium in place. The capsules were placed in a molybdenum resistance furnace and heated at 2000°F (1100°C) for 100 hr. On cooling, the specimens were cut and examined metallographically. Fig. 1 is a micrograph at X250 of a portion of the interface from a transverse section. Four phases are clearly visible, with sharp boundaries between them. Phase A is a section of the molybdenum capsule; phase B is the molybdenum-rich intermetallic composition MoBe,; phase C is the beryllium-rich compound MoBe13; phase D is a section of the beryllium rod. All phases were readily polished to a high metallic luster. The molybdenum-rich phase has a pronounced purple tinge. The beryllium-rich phase (C) is only slightly darker than the pure beryllium. In polarized reflected light, however, it shows striking birefringence between crossed Nicols. The black areas represent flaws or pores in the material. A small representative amount of powdered material from each of the phases was carefully removed under the microscope with a diamond tool. With this material, powder X-ray diffraction patterns were made for the identification of each phase. Table I lists the X-ray diffraction spacings and corresponding indexes characteristic of these intermetallic compounds. Synthesis To establish the formula of the new intermetallic compound, X-ray diffraction patterns were made from powders obtained from solidified melts of known composition. The syntheses were made by

Jan 1, 1952

By John Chipman, Minu N. Dastur

This paper presents equilibrium data on the reaction of water vapor with vanadium dissolved in liquid iron at 1600°C. The thermo-dynamic behavior of vanadium and oxygen when present together in the melt is discussed. A deoxidation diagram is presented which shows the concentrations and activities of vanadium and oxygen in equilibrium with V209 or FeV2O4. STUDIES of the chemical behavior of oxygen dissolved in pure liquid iron1-3 have served to determine with a fair degree of accuracy the thermody-namic properties of this binary solution. The practical problems of steelmaking, however, involve not the simple binary but ternary and more complex solutions. Only a beginning has been made toward understanding the behavior of such systems. The silicon-manganese-oxygen relationship was studied long ago by Korber and Oelsen4 and more recently by Hilty and Crafts." The carbon-oxygen reaction was investigated by Vacher and Hamilton6 and by Marshall and Chipman.7 A number of deoxidizing reactions have been studied empirica1lys'10 with the object of determining the appropriate "deoxidation constants." The work of Chen and Chipman" afforded a clear-cut view of the effect of the alloy element, chromium, on the thermodynamic activity of oxygen in liquid ternary solutions. These investigators determined the oxygen content of experimental melts which had been brought into equilibrium with a controlled atmosphere of hydrogen and water vapor and were able to show that the presence of chromium decreases the activity coefficient of oxygen. They determined also the conditions under which the two deoxidation products, Cr2O3 and FeCr2O4, were formed and showed that the activity of residual oxygen is considerably less than its percentage. It was the object of this investigation to apply a similar method to the study of molten alloys of iron, vanadium, and oxygen. Vanadium was once considered a moderately potent deoxidizer, but this is now known to be erroneous, in the light of its behavior in steelmaking practice. Its reaction with oxygen retains a certain amount of practical interest in that a high percentage of one element places a limit on the amount of the other that can be retained. As a deoxidizer it will be shown that vanadium lies between chromium and silicon. Experimental Method The apparatus was that used by the authors3 in their study of the equilibrium in the reaction: H2(g) +O = H2O(g);K,= [1] PII., ao Crucibles of Norton alundum or of pure alumina were used. The latter were made in this laboratory and were of high strength and low porosity. Under conditions of use they imparted no significant amount of aluminum (less than 0.01 pct) to the bath. Temperature measurements were made with the optical equipment and calibration chart of Dastur and Gokcen.= The charge was made up of calculated amounts of ferrovanadium (20 pct V) and clean electrolytic iron totaling approximately 70 g. The first few heats were made in alumina crucibles with an insufficient amount of vanadium so that no oxide of vanadium would be precipitated under the particular gas composition. All the heats were made at 1600 °C under a high preheat and with four parts of argon to one part of hydrogen in the gas mixture to prevent thermal diffusion. The rate of gas flow was maintained constant at 250 to 300 ml per min of hydrogen. The time for each heat was three quarters of an hour after the melt had melted and attained the required temperature (1600°C). The water-vapor content of the entrant gas mixture was gradually raised in succeeding heats, keeping the vanadium content of the melt constant. This was controlled by manipulation of saturator temperature. A point was reached when for a given H2O:H2 ratio some of the dissolved vanadium was oxidized and appeared as a thin, bright oxide film on top of the melt. By raising the temperature of the melt it was possible to dissolve the oxide film which reappeared as soon as it was cooled down to 1600°C. The temperature readings taken on the oxide film were consistently higher by 80" to 85 °C as observed by the optical pyrometer. The heat was allowed to come to equilibrium under a partial covering of this oxide film. At the end of the run the power and preheater were shut off and the crucible containing the melt was lowered down into the cooler region in the furnace. This method of quenching proved quite

Jan 1, 1952

[ ] For President-Elect Leo F. Reinartz has been nominated for the Presidency of AIME in 1954. Mr. Reinartz is now vice-president, special operating development, Armco Steel Corp. He was born in East Liverpool, Ohio, and graduated from the Carnegie Institute of Technology as metallurgical engineer. He joined Armco in 1909 as a chemist and then became open hearth foreman; assistant superintendent, open hearth dept.; superintendent, open hearth dept.; assistant general superintendent; works manager, East works; manager, Middletown div.; and assistant vice-president, successively. Mr. Reinartz has been active in many technical societies and delivered papers before several. He has been the recipient of the Alumni Award from Carnegie and holds life honorary membership in the AIME National Open Hearth Conference. One of the organizers of the National Open Hearth Conference, Mr. Reinartz was Chairman, Executive Committee (1927 to 1946) and is presently Chairman of its Finance Committee. In October 1951 he was an American Conferee at the First World Metallurgical Congress held in Detroit. An AIME member since 1925, Mr. Reinartz has been active on numerous committees of the Institute.

Jan 1, 1952

By Charles W. Sweetwood

THE Western phosphate field, virtually ignored for 40 years, has been undergoing a rapid climb to economic importance. Until World War II there seemed to be no reason for developing the phosphate rock region of the Intermountain Empire. But the tremendously increased demand for food production and the needs of many branches of the chemical industry changed all that. Quite suddenly a report made by the U. S. Geological Survey at the turn of the century became important. The survey showed that 60 pet of the nation's phosphate reserves were in the western phosphate field. Simplot Fertilizer Co. was one of the first to become actively interested in the development of the area. In August, 1945 the company began exploration of the Phosphoria Formation on the Fort Hall Indian Reservation. The result was the Gay Mine, about 18 miles east of Indian Agency Headquarters at Fort Hall, Idaho, developed to supply high grade phosphate rock for processing into superphosphate fertilizer at the company's Pocatello plant. Six ft of high grade oolitic phosphate rock (ranging from 32.5 to 34.5 pet P2O5) were discovered at the base of the Phosphoria Formation by diamond drilling and dozer trenching. High quality and thickness, plus the fact that the formation lay flat and near the surface made strip and open pit mining possible. In one year of mining, starting June 1946, a total of 53,000 tons of main bed oolitic phosphate rock was hauled to Pocatello for processing into supersulphate. The first year's operation was in

Jan 1, 1952

By F. J. Dunkerlery, V. Damiano, J. Fulton, F. Pledger

Grain-growth and recrystallization characteristics of a commercially pure zirconium prepared by the iodide process are reported. Grain growth from 640° to 800°C was continuous once initiated and obeyed D = kt". Recrystallization of zirconium occurred at temperatures of 450° to 550°C after deformations of 20 and 50 pct. Hardening from partially soluble inclusions prevented determination of the absolute rates of recrystallization, but the relative rates of recrystallization obtained are useful as a guide in fabrication practice. BASIC information needed as a guide in the hot and cold working and annealing of metals includes recrystallization and grain-growth data. A search of the literature revealed no such information for pure zirconium. This is a report of practical grain-growth and recrystallization results obtained for a commercial grade of pure zirconium on a project sponsored by the Office of Naval Research. In this work, isothermal grain-growth curves were obtained at five temperatures from 640" to 800°C inclusively; while recrystallization curves have been determined at 450°, 500°, and 550°C for the metal at the deformation levels of 20 and 50 pct. In addition to the usual variables of temperature, time, and deformation, distribution of the second phase found in all commercial grades of iodide zirconium is also treated as an important factor in these grain-growth and recrystallization studies. In conducting this work, two properties of zirconium were particularly pertinent in dictating experimental conditions. First, since zirconium undergoes a transformation from the a close-packed hexagonal form to the ß body-centered cubic form at 862°C, no recrystallization or grain-growth studies were made above 800°C. Second, because dissolved gases (oxygen, nitrogen and/or hydrogen) increase the hardness and lower the ductility of the solid metal, all annealing treatments in this investigation were carried out in vacuum or in a helium atmosphere. Materials and Methods The zirconium used in this investigation was prepared by the Foote Mineral Co. by deposition from its iodide. A spectrochemical analysis of the metal showed the following composition in weight pct: Hf, 2.1; Mg, 0.012; Fe, 0.035; Si, 0.095; Ti, 0.023; Al, 0.037; Mo, trace; Ni, trace; Cr, trace; Ca, 0.006. Conventional metallographic procedures involving hand polishing on wet metallographic papers, followed by final polishing on fine, levigated alumina on gamal cloth and a medium speed wheel were used throughout this investigation. Grain boundaries were revealed with modified Tucker's etch containing 20 parts glycerine, 2 parts hydrofluoric acid, and one part nitric acid. Grain-Growth Procedure: Three lots of zirconium, designated here as series A, B, and C were prepared for the grain-growth studies as follows: Series A was prepared by cold swaging the % in. as-deposited rod to a 3/16 in. final diameter, followed

Jan 1, 1952

By J. C. Gilbert

"IntroductionTHE PURPOSE of this paper is to discuss in a general way the heavy oil situation in Western Canada, and particularly to acquaint those in the oil industry who have not participated in the heavy oil end of the business with past and current developments. The author has covered •briefly the location of the heavy •and asphalt-base oil fields, their geology, current drilling and production practice, the location of the •refineries capable of handling heavy crude, their products and markets, and the problems and future prospects of the industry.Location and Description of FieldsThe term heavy oil is generally used to denote crude of 20.9° gravity and under. Since the products from heavy oil are also to a lesser extent obtained from asphalt-base crudes of higher gravity, some mention will be made here of the latter; but in general the emphasis of the paper is on heavy oil as such.In the order of their production to date, the heavy oil fields and those light oil fields which produce asphalt-base crudes are : Lloydminster, Taber, Vermilion, Conrad, Princess, and Wainwright.The Lloydminster oil field has not only produced most of the heavy oil, but also is currently the largest producer, supplying at the present time about 80 per cent of the heavy and asphalt-base crudes produced in Western Canada."

Jan 1, 1952

By Theodore Kootz

Manufacture of high-grade ferromanganese; as a rule; requires a low-phosphorus-manganese ore with 45 to 55 percent Mn, chiefly obtained in the Soviet Union, the British Dominions, and Brazil. Also, low-manganese ores have already been used for ferromanganese production, especially in North America .and Germany. During World War I, a process was developed in which a high-phosphorus ferromanganese or spiegeleisen was prepared in the blast furnace from law- or high-phosphorus manganiferous ores, then low-phosphorus manganese slag was prepared by refining under an acid slag, and this material was, worked into a low-phosphorus ferromanganese in the blast furnace.9/ Manufacture of useful manganese ores from a phosphorus-bearing spiegel with 12 to. 15 percent Mn, 4.5 percent C,, and 0.5 percent P by slagging in a refining furnace was reported by Joseph, Barrett, and Wood.10/ The spiegel was refined to 0.75 percent Mn, 3.4 percent C, and 0.45 percent P. Thereby, a slag with about 43 to 58 percent Mn and, about 10 percent Si02, was obtained. Hotter melts gave a smaller phosphorus content in the slag than cold melts. In addition, the phosphorus content of the slag varied with the manganese content of the intermediate metal.

Jan 1, 1952

John Eliot Allen has been made acting head, dept. of geology, New Mexico Institute of Mining and Technology, Socorro, N. Mex. He had been associate professor of geology. Robert B. Anderson has accepted a position with the U. S. Steel Co., Gary, W. Va., as assistant to the superintendent, No. 2 mine. [ ] Donald L. Archibald has joined the sales dept. of the Ellicott Machine Corp., Baltimore. He formerly had been associated with the Joy Mfg. Co., St. Louis. J. C. Boswell has been appointed manager of the Fairbanks dept., United Smelting Refining & Mining Co. J. B. Metcalfe has been appointed assistant to the president. G. Howard LeFevre was elected vice-president and general manager of metal sales and R. N. Hunt, vice-president and chief geologist was elected a director. R. B. Earling, vice-president and general manager of Alaskan operations, has retired but. will con¬tinue to serve on the board of directors. J. D. Crawford has been appointed general manager of Alaskan operations.

Jan 1, 1952

ASSETS Working Fund Assets Cash-unappropriated $62,41294 Members' 1951 dues receivable 14,336 98 Accounts receivable Advertising, publications and miscellaneous $43,22055 Less-Reserve for delinquent accounts 12,775 76 $30,44479 Petroleum Branch-Special Projects Fund¬ Advances re Petroleum Conservation Volume 5,37085 35,81564

Jan 1, 1952

Aamot, Olav Crone, (Member '29) Met , Det Norske Aktieselskab for Elektrokemisk, Industry, Inc , Oslo, Norway Aase, Glenn D , (Junior Member '40) Met Engr , Western Research Dyv , American Smelt & Refin Co , Selby, Calif Abadye, Henry G., (Member '43) Petr Engr , Sr Prod Engr , Long Beach Oil Development Co, 255 So Santa Clara Ave, Long Beach, Calif Abbott, Clarence E , (Member '04) Civil Engr , 'P , Tennessee Coal, Iron & R R Co , 1542 Brown Marx Bldg Birmingham, Ala Abbott, Fred E , Jr , (Member '44) Petr Engr , c/o Arabian American Oil Co , A P 0 816, c/o Postmaster, New York, N Y Abbott, John H , (Member '46) Resident Mgr , Hickman, Williams & Co, 230 No Michigan Ave, Chicago 1, Ill Abbott, R W R., (Member '47) Asst Power Supt, Cananea Consolidated Copper Co , Cananea, Son , Mexico Abbott, Robert H? Jr., (Junior Member '47) Petr Engr, Producing Dept, The Texas Cc, P 0 Box 951, Houma, La Abel, Raymond L., (Member '28) Chem Engr, Prof of Chem Engrg, Univ of Pittsburgh, Pitts¬burgh Pa Abel, Walter D , (Member '32) Min Engr, Div of Corporations, 403 State Bldg , Los Angeles 12, Cal if

Jan 1, 1952

By M. J. Spendlove, H. W. St. Clair

An automatic surface-follower mechanism was used to measure the surface temperature and the rate of evaporation of molten zinc while undergoing distillation at low pressure. At pressures of 50 to 100 microns Hg, the rate of evaporation may be 60 to 80 pct of the theoretical maximum corresponding to the measured temperature. The rate decreases rapidly at pressures above 100 microns Hg, to only 7 pct of the theoretical maximum at 2000 microns Hg. Measured temperature gradients at the surface are in agreement with theoretical gradients calculated from the heat of vaporization, rate of evaporation, and thermal conductivity of molten zinc. THIS paper covers a series of careful measurements of the rate of evaporation of molten zinc at low pressures, undertaken as a part of a general investigation on the separation of metals by distillation.' Preliminary results on the rate of evaporation of zinc were described in a previous publication.' The results of the preliminary study are as follows: 1—The observed rates of evaporation of zinc were as high as 0.60 g per sq cm per min, corresponding to 75 pct of the maximum rate as determined by the temperature of the metal. 2—The evaporation rate was decreased from 0.30 g per sq cm per min at a pressure of 25 microns to only 0.09 g per sq cm per min when the pressure was increased to 5 mm. 3—The temperature of the surface during rapid evaporation may be 35" to 100°C less than the main mass of metal. Observed temperature gradients at the surface are consistent with those calculated from the heat of vaporization and the thermal conductivity of liquid zinc. In the preliminary experiments, the rate of evaporation was determined from the loss in weight of the metal in the crucible during the test. This was compared with the weight of the condensate. Obviously, this method was subject to error because of some uncertainty as to the period of evaporation that should correspond to the loss in weight. Furthermore, this method did not permit taking into account probable variations in the rate of evaporation during the test. A more serious shortcoming was that the temperature at the evaporating surface was not known, so the maximum theoretical rate of evaporation could not be calculated accurately. To improve the precision of rate measurements and to allow accurate measurements of the surface temperature, a refined experimental technique was developed whereby the temperature and position of the surface could be measured accurately. This was done by an automatic surface-follower mechanism that gave a continuous record of the surface temperature and the amount of zinc evaporated. These data permitted an instantaneous determination of the actual rate of evaporation and the surface temperature throughout the test. Pure zinc (99.99 pct Zn) was used in all experiments. Description of Distillation Furnace The details of construction of the distillation furnace are shown in Fig. l. The furnace is enclosed in a large quartz tube open at one end. The open end of the quartz tube is sealed by means of a water-cooled head. The entire enclosure is vacuum tight. The connection between the water-cooled head and the quartz tube is sealed by means of a rubber gasket which fits tightly against the smooth end of the tube. The metal is heated by induced current set up in the molten zinc and the walls of the graphite crucible by means of a water-cooled induction coil outside the quartz tube. High frequency current is passed through the induction coil from a 6 kw mer-

Jan 1, 1952

By J. D. Bateman

At Giant Yellowknife, where high grade gold-bearing orebodies are highly irregular in shape, geology has been applied extensively to the mining of ore. The classical functions of the mine geologist in the fields of exploration and mine development have been extended to guide ore extraction, ensuring "clean" mining and effectively reducing waste dilution. THE property of Giant Yellowknife Gold M.ines Ltd. is situated west of Yellowknife Bay on the north shore of Great Slave Lake, a distance of 600 air miles north of Edmonton, Alberta. The Giant claims were staked in 1935, the company was formed in 1937, and the main orebody system was disclosed by diamond drilling in 1944 following a geological study of the property by A. S. Dadson,* Consulting Geologist for the company. Production began in 1948 at the rate of 200 tons per day and, during 1950, reached a daily rate of 425 tons. During the first 3 years of operation a total of 366,000 tons was milled with an average grade of 0.79 oz of gold per ton. Work is in progress with an expansion to 700 tons per day in view. A descriptive account of the geology and gold-bearing shear zone has appeared previously.* The rock formations in the vicinity of Yellowknife Bay have been subjected to protracted pre-Cambrian tectonic deformation culminating in a series of late faults having a cumulative horizontal displacement exceeding 11 miles. The Giant property is underlain by part of an Archean sequence, several miles thick, consisting of basic volcanic flows and minor intercalated tuffs. The volcanic succession forms the west limb of a major syncline, the flows facing east, but overturned on Giant property to dip west at 65" to 75". Orebodies are confined to shear zones up to 200 ft in width, which were formed along early thrust faults. The shear zones assume fold-like attitudes, the larger of which have an amplitude of several hundred feet. The rock formations beyond the limits of the zone of shearing do not reflect the simulated folds, the axes of which are within a few degrees of the strike of the flows. The schistosity and most of the planar elements in both the shear zones and the orebodies dip west • A. S. Dadson and J. D. Bateman: Structural Geology of Camdian Ore Deposits, Can. Inst. Min. Met. Jubilee Volume (1948), PP 273-283. at angles between 65" and 75", generally corresponding to the dip of the flows. The planar elements within the shear zone system thus dip more or less constantly west whether the shear zone is flat, vertical, or expressed as east or west dipping limbs. The shear zones reflect the deformation and alteration of the basic volcanic flows into chlorite schists which, in most places, have undergone metasomatic replacement to form chlorite-sericite-carbonate schists or sericite schists. The boundaries between the shear zones and country rock, although often gradational, usually can be defined within a few feet or even inches as they are expressed by the limits of metasomatic alteration. Orebodies may occupy a small or large proportion of the shear zone and, although they generally conform to the shape of the zone, their morphology is much more complex. Ore boundaries in some instances are sharp and can be delineated with a chalk line; but more generally, a large proportion of the ore boundaries is not visually obvious and can be determined only by the perception acquired by the geological mapping of ore or study of drill cores. Ore shoots in fold-like attitudes may transect the planar elements of the shear zone at any angle; yet the schistosity within the ore shoot may be coincident with that in the enclosing shear zone. Thus it is clear that problems may arise in the delineation of mining boundaries. Ore generally consists of 20 pct or more quartz with ferruginous carbonates in sericite schist deposited in two dominant stages. The earlier stage limits of quartz with carbonate, pyrite, and very fine-grained arsenopyrite in lenses and bands. The later stage consists of quartz-carbonate lodes, in

Jan 1, 1952

By D. M. Dunbar

LONG before Columbus discovered America the original inhabitants toiled in the copper workings of the Andean Cordillera. Their best diggings appear to have been at Chuquicamata, site of the huge present-day open pit owned by the Chile Exploration Co., subsidiary of Anaconda Copper Mining Co. Located in Antofagasta Province of northern Chile, Chuquicamata is in the Atacama desert, high on the western slope of the Andes at 9500-ft elevation. In the Chuquicamata area the Atacama desert merges into the Cordillera. The climate is extremely arid and precipitation, either in the form of rain or snow, is very infrequent. The temperature varies from 50° to 85°F during the day, and drops to 20° to 40° at night. The Antofagasta and Bolivia Railroad, which connects the Chilean Port of Antofagasta with La Paz, Bolivia, passes within approximately 6 miles of the plant. A branch from the main line to Chuquicamata serves the property for outgoing copper and incoming freight. The distance to Antofagasta by rail is 163 miles. Previous to the Inca conquest, this region was inhabited by the Chuco Indians, a small tribe, descendants of the Aymaras and Quechuas. The Incas, whose capital was located in Cuzco, Peru, gradually extended their empire to the south, reaching at one time to what is now central Chile. It is believed that they built crude primitive furnaces on the banks of the Rio Salado where on a small scale they smelted copper ore from Chuquicamata. At the time of the subsequent Spanish conquest, legend has it that Diego de Almagro, on his return to Cuzco in 1536 after his invasion of Chile, obtained from these furnaces metallic copper for horseshoes. During the period from 1560 to 1879 the high grade veins of the Chuquicamata deposit were worked superficially by the Spaniards and Bolivians. The treaty signed after the war of 1879 recognized the sovereignty of Chile over this territory and Chile, realizing the importance of the district, started to develop it in an orderly manner, although only high grade veins were worked. New Process Is Key Reports on the deposit were brought to the attention of Albert C. Burrage, a Boston lawyer and financier, in 1910. Chuquicamata was described as a huge deposit of ore that was not amenable to the usual treatment by concentrating and smelting since much of the copper occurred as oxides. He had been working on a process for the recovery of copper from sulphide ore which involved a sulphating roast, leaching of the roasted product, and pre-

Jan 1, 1952

By Henry Lewelling

An experimental investigation of the relative effectiveness of standard bullets and "shaped charges" in perforating dense, hard formations is reported. A method is described which simulates the conditions under which a shot is normally fired. Results are evaluated on the basis of depth of penetration, extent 01 Fracturing. extent and nature of formation damage, and other physical characteristics. INTRODUCTION A study was made of the relative merits of bullets and "shaped charges'' as applied to well completions in hard, dense formations such as those encountered in the Permian Basin. The planning of the laboratory program stipulated that core samples should be prepared and mounted in such a way that perforation shots of either kind"" could be fired into them, keeping the factors pertinent to good shooting practice similar to what they would be in a well. The shooting was done in a buried tank. with the sample and shooting equipment covered with water. The depth of water was calculated to he sufficient to simulate the inertial effects of well fluids for the duration of an explosion (a few micro-seconds). Flow measurements were attempted on the specimens after perforation. Due to the lack of uniformity of the limestone, shale breaks. etc., these measurements proved to be of little value to the study. The mounting materials were removed. so that the character of the penetration. fracturing, etc., could be observed. METHOD Laboratory samples were selected from the hard. dolomitic sand cores from Block 31 Field. Core pieces having a 3 3/4 in. diameter and a useful length of 10 to 12 in. were used. Selection was aimed at those pieces having a minimum of shale streaks and other irregularities. The ends were cut off square Manuscript received in the Petroleum Branch office June 28, 1951. Paper presented at the Petroleum Branch Fall Meeting in Oklahoma City, Okla., Oct. 3-5, 1951. with the diamond saw. Prior to lbeing mounted. the cores were soaked in water to prevent them from absorbing water out of the wet concrete, thus weakening it. A set of steel capsules was fabricated for holding the core Samples. Seven-in. casing was cut in two-ft lengths. of which one end was closed by "orange-peeling" and welding, and the other was threaded to accept a standard bull plug. The bull plugs were fitted with copper tube connections .so that pressure could be applied when the capsules were made up. The cores were mounted in the capsules by means of wire centralizers whose function was to hold the Core in proper position while concrete was poured and set. A special aggregate was prepared wing a graded sand and gravel mixture

Jan 1, 1952

By Robert Glass Cleland

THOUGH the rapid revival of the copper market in the early twenties solved the most serious of the company's immediate postwar difficulties, a much more fundamental, long-range problem still remained. Mining is not like farming: the earth does not bring forth a new crop of gold, silver, lead, zinc, oil, or copper at every harvest time. Metal taken from the ground does not spring up again from the old roots like perennial flowers in a garden, or find renewal in freshly sown seed. No ore body, whatever its size or richness, is too big or too rich to escape ultimate exhaustion. When the war closed in 1918, Phelps Dodge had been mining copper from Bisbee, Morenci, and Nacozari over periods varying in length from ten to nearly forty years. During much of that time, the company's production had run from fifty million to as high as two hundred million pounds a year. Even the greatest of mines had to respond in time to such a drain. High grade ore was already at a premium in Bisbee and Morenci. The Burro Mountain properties of New Mexico were a disappointment. Failing the acquisition of

Jan 1, 1952

By L. W. Vollmer

Introduction During the past three years at least fifty strings of 9% nickel steel tubing have exhibited excellent resistance .to the variably severe corrosive conditions typical of many of the sweet condensate wells in Mississippi, Louisiana, and Texas. This experience, and the characteristically outstanding performance of other ?nickel alloy steels under hydrogen sulphide corrosive conditions, dictated the selection of 9% nickel steel tubing for the second well drilled in the sour condensate Pincher Creek field of southwestern Alberta. The damaging effects of the Pincher Creek reservoir fluids on well equipment had been manifested in the discovery well by the rapid and not yet fully understood failure of API Grade N-80 tubing, stainless steel wire lines, and alloy steel fishing tools. Two very unexpected failures in the 9% nickel steel tubing, after only six days of service in production tests, instigated an extensive and continuing investigation to ascertain the probable cause of failure. This discussion presents some of the results obtained thus far which cast a little light on the perplexing behaviour of steels in hydrogen sulphide environments in general, and in sour condensate wells in particular. History of Tubing Failures Walter Marr well No. 1, in which the 9% nickel steel tubing failures occurred, produces from the Madison lime at the depth interval approximately 12,200 to 12,750 feet. The gas-oil ratio is about 26,000 and the gas contains 10.2 per cent hydrogen sulphide and 6.3 per cent carbon dioxide by volume.

Jan 1, 1952

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION Transactions Number Place Date Vol Page 1 Wilkes-Barre, Pa May, ?71 1 3 2 Bethlehem, Pa August, ?71 1 10 3 Troy, N Y November, ?71 1 13 4 Philadelphia, Pa February, ?72 1 17 5 New York, N Y May, ?72 1 20 6 Pittsburg, Pa October, ?72 1 25 7 Boston, Mass February, ?73 1 28 8 Philadelphia, Pa May, ?73 2 3 9 Easton, Pa October, ?73 2 7 10 New York, N Y February, ?74 211 11 St Louis, Mo May, ?74 3 3 12 Hazleton, Pa October, ?74 3 8 13 New Haven, Conn February, ?75 3 15 14 Dover, N J May, ?75 4 3 15 Cleveland, 0 October, ?75 4 9 16 Washington, D C February, ?76 4 18 17 Philadelphia, Pat June, ?76, 5 3 18 Philadelphia, Pa October, ?76 5 9 19 New York, N Y February, ?77 5 27 20 Wilkes-Barre, Pa May, ?77 6 3 21 Amenia, N Y October, ?77 6 10 22 Philadelphia, Pa. May, ?78 6 18 23 Chattanooga, Tenn May ?78 7 3 24 Lake George, N.Y. Oct. ?78 7 25 Baltimore, Md. Feb. ?79 7 26 Pittsburgh Pa, May ?79 8 27 Montreal, Canada Sept, ?79 8 28 New York, N.Y. Feb, ?80 9 29 Lake Superior, Mich Aug, ?80 9 30 Philadelphia, Pa. Feb, 81 9 31 Staunton, Va May, 81 10 32 Harrisburg, Pa Feb, 81 10

Jan 1, 1952

By J. C. Detweiler

THE Jacksonville plant of Humphreys Gold Corp., operating under leases from National Lead Co. and Rutile Mining Co. of Florida, recovers rutile, ilmenite, zircon, and monazite from an ancient beach deposit containing about 2.5 pct of these minerals in combination. The location of the plant is unique, being situated about ten miles from the center of Jacksonville, Fla., surrounded by a thriving suburb. Two four-lane highways pass within 1 ½ miles of the plant. An expressway now under construction will pass over the tailing pile, within 500 ft of the mine office. The elevation at the plant site is approximately 50 ft above sea level. This is one of two mines producing titanium minerals and zircon in Florida. Another mine is also operated by Humphreys at Starke, about 50 miles southeast of Jacksonville. The Jacksonville deposit extends about six miles in a north-south direction, averaging approximately one half mile wide and twenty ft thick. Values begin at the surface over most of its length and ter-

Jan 1, 1952

The regular activities of the Institute are financed mainly by income derived from members' dues, from advertising in MINING AND METALLURGY, and from the sale of publications to the public In addition, collateral activities and special projects are financed each year by means of income from endowed funds controlled and administered by the Institute In the aggregate, the amount of these endowments totals more than $830,000 An active effort is being made to increase the endowment funds of the Institute through a standing committee, of which Harvey S Mudd is Chairman, and

Jan 1, 1952

Manganese ore from the Black Rock, Kramer, and Black Jack mines in Tooele and Jaub Counties, Utah, are of acceptable grade, the U. S. Bureau of Mines has announced. Payment of a premium price of 252¢ per lb to the Copper Range Co., of Michigan for the output of its White Pine mine, has been agreed to by the DMPA. The contract will be limited to $28.6 million worth of copper. The agreement follows an RFC loan grant of $57 million to bring the White Pine property into production within three years. Increases of 5 to 6 cents over the Lake copper ceilings have been granted to the Calumet & Helca Consolidated Copper Co., for operation of "high cost" deposits, according to Jess Larson, DMPA administrator. Mr. Larson expects the move to add about one million lb of copper per month to the supply. The agreement can be cancelled on 60 days notice and is terminated automatically in the event copper ceilings are removed.

Jan 1, 1952