Search Documents

By Ernest L. Ohle

IN 1943 diamond drilling from the surface in an area 2 miles southwest of Leadwood, Mo., discovered a lead deposit of a markedly different character from the usual southeast Missouri type. Subsequent drilling of about 500 holes indicated several million tons of ore, and in 1950 a 701-ft vertical shaft was sunk into the orebody. This paper describes the geology, of this interesting occurrence insofar as it is known from the drilling and the small underground exposure at the bottom of the shaft. Geology The location of the Southeast. Missouri Lead Belt and of 'the Hayden Creek property are shown in Fig. 1. As shown here, there are two separate producing areas, one from which the larger tonnage has come, located near Bonne Terre, Flat River, Desloge, and Leadwood, and the other to the south around Fredericktown and including famous old Mine LaMotte. The best published description of Lead Belt geology is by Tarr.* In pre-Cambrian time in this cherty dolomites. Several of these formations may be found in direct contact with the pre-Cambrian as their deposition progressively overlapped the older rocks on the flanks of the igneous knobs and ridges. Immediately overlying the pre-Cambrian there is, not uncommonly, a thin basal conglomerate of granite or porphyry boulders, which is incorporated into the overlying sediments. Deposition of the lower part of the rock section was fairly continuous, and the Lamotte sometimes grades almost imperceptibly into the lower sandy Bonneterre. Since the sediments were deposited on an uneven floor, they tend to reflect the irregularities in that floor. Most of the steep dips found in the district, that is, dips in excess of 10°, are original dips and not caused by deformation. Such domelike structures in the sedimentary rocks around the igneous knobs have localized a considerable number of the orebodies in the district and particularly those in the Fredericktown area. Many of the larger orebodies, however, have no close relation to the pre-Cambrian topography. Most of the lead production has come from the lower 150 ft of the Bonneterre formation, where disseminated ore spreads laterally parallel to the bedding for great distances. Average stoping height is about 20 ft, but in a few places there are stopes over-175 ft high.

Jan 1, 1952

By J. B. Zadra

After the discovery of the rare-earth mineral deposit in the Clark Mountain area near Mountain Pass, San Bernardino County, Calif., two samples wore obtained through the Mining Division of the Bureau of Mines for investigation of possible method of concentration. Three other samples were received later from different locations in the same area. The rare-earth mineral in this ore had been identified by E. T. Schonk as bastnaesite, a fluocarbonate of the rare-earth metals containing cerium, lanthanum, praseodymium, thorium, uranium, etc. Associated with the bastnaesite were barite, silica, and some calcite. The bastnaesite contained a small amount of iron as a coloration and some manganese. Twenty to fifty percent of the weight of the samples studied was bastnaesite, or ten to twenty-five percent total rare-earth oxides; about half was cerium oxide. Apparently, none of this mineral occurred in pure form. Even the highest-grade particles 'wore contaminated by fine, interlocked grains of barite, calcite, and silica; barite contamination predominated, and the barite was interlocked with varying amounts of bastnaesite. While the specific gravities of pure bastnaesite and barite (approximately 5.0 and 4.50 respectively) differ enough to allow separation by gravity, the interlocking of the minerals nullified this difference. Consequently, only a partial separation could be made by gravity concentration. The extremely fine grained texture of most of the ore prevented grinding to a size that would make concentration by flotation practicable; a partial separation of barite by this means was effected.

Jan 1, 1952

JAMES A. BARR Consulting Engineer Mt. Pleasant. Tennessee Washington. D.C. BEHRE DOLBEAR G COMPANY Consulting Mining Engineers and Geologists 11 Broadway New York 4, N. Y. BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Monticello, Georgia GLENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 210 La Arcada Bldg. Santa Barbara, Callf.

Jan 1, 1952

By G. W. Jones

From evidence made available during the investigation, it was concluded that the first of a series of explosions occurred at 1:15 to 1:20 p.m. September 21, 1951, in an underground vault that housed pressure regulators on the gas-distribution lines that served Brighten. This explosion damaged the pressure regulators and permitted high-pressure gas to enter the distributing mains and individual-service lines. As a part of the gas-distribution system was not provided with means for protection against such excessive pressures, gas gained access to the interiors of many residences in this area and caused a series of disastrous explosions and fires, which took place during a period of approximately 2 hours after the initial explosion in the pressure-regulator vault. Two persons were killed in the first explosion in a residence, and a third person died of a heart attack attributed to the excitement that prevailed during the explosions and fires, Twenty-three persons were listed as injured. Forty-one residences were either destroyed or damaged - 11 by explosion and the remainder by fires, which developed as a result of gas leakage into residences. Fifteen residences were listed as "completely down" or "gutted." Unofficial estimates of property damage ranged from $1,000,000 to $1,500,000. In view of observations made and information obtained during the investigation, recommendations are presented in this report relative to the natural-gas distribution system in Brighton, which may be helpful in the prevention of similar accidents in this and other communities.

Jan 1, 1952

•Mineral Development Corp. of Salt Lake City, Utah purchased the Somerset and Oliver coal mines from the Kaiser Steel Corp. The mines are located at Somerset, Colo., about 75 miles east of Grand Junction, Colo. Somerset Town, with housing for 600 persons was included in the transaction. The mines employ 115 miners and have a combined capacity of 1750 tons per day. The Minerals Development Corp. is headed by Claude P. Heiner and is controlled by Godfrey L. Cabot, Inc. of New York and Boston. The Cabot Company is a major producer of carbon black. • The Dept. of Interior has announced that the name of the Defense Minerals Administration will be changed to Defense Minerals Exploration Administration. The new name of this defense agency more nearly describes its duties, since the mineral programming, procurement and claimant functions of the former DMA have been transferred to the Defense Minerals Procurement Agency. C. O. Mittendorf, formerly acting administrator of DMA, is serving as acting administrator of the new DMEA.

Jan 1, 1952

By E. Swartzman

"DURING 1951, experimental cleaning studies on both fines and larger sizes of certain Canadian coals were conducted on a relatively large scale in two pilot plants in the United States, large enough to be considered as small commercial units, and in one commercial plant in Canada.One of the pilot plants was a wet washer of a type which apparently has never been .used in Canada, nor has any Canadian coal been tested in it before. In the other pilot plant and in the commercial plant, dry cleaning equipment was used. The commercial plant is the first of its kind to be employed in Canada, and this type is used only to a limited extent in the United States.Fine-Coal Cleaning ExperimentsTest PlantsHydrotator and Hydrotator-Classifier combination pilot-plant with a capacity of about twenty tons per hour. This is a classifier type washer adapted for cleaning fine coal as well as certain intermediate sizes. The Hydrotator deals with that portion of a coal retained on approximately a 24-mesh Tyler sieve, whereas the Hydrotator-Classifier deals with the minus 24-mesh fines."

Jan 1, 1952

[ ] (14) SCREENS: Description of Allis-Chalmers' complete line of vibrating screens for the mining industry is contained in a new 8-page bulletin. Primary scalping, secondary scalping, and conventional screens for wet or dry sizing and screens for heavy media separation are included. Also given is a typical fiowsheet showing how horizontally operated Low-Head screens are used in the sink and float process. (15) MILLS: Forty-six years of experience and 4000 installations throughout the world lie behind the seven basic types of mills illustrated in a recent bulletin from the Hardinge Co. Fields of application and materials handled in various installations are listed. (16) BLOWERS & COMPRESSORS: A brochure describing the manufacturing facilities and the axial and centrifugal blowers and compressors made by the Sawyer Bailey Corp. is now available. (17) LINATEX: The first catalog of the Linatex Corp. of America has been issued, outlining the advantages claimed for this special form of natural rubber, when used in corrosion, abrasion, and vibration resisting applications. (18) WIRE ROPE: Twenty-four pages packed with concentrated wire rope data is the way E. H. Edwards Co. describes a booklet which they are now making available. It was condensed from the Edwards general catalog to provide users with a concise guide to every important phase of wire rope production, maintenance, and use.

Jan 1, 1952

By A. Kenneth Schellinger

THE terms surface tension .and surface energy are well known when applied to liquids and are generally described by referring to the excess energy of the air: liquid interface as a result of unsaturated molecular forces surrounding the surface molecules of the liquid due to the presence of the air phase on one side. Such unbalanced forces produce the familiar water droplet of spherical form and are generally summed up as a surface tension measured in dynes per centimeter which can be shown mathematically to be equal numerically to a corresponding surface energy expressed in ergs per square centimeter. A specific surface energy, however, is best thought of as the energy necessary to produce one unit of new surface on a substance. Hence, in producing a bubble in a flotation cell the impeller must supply surface energy corresponding to the air: liquid interfacial area on the interior of the bubble. Inasmuch as it is relatively easy to extend or contract the surface of a liquid, there are a number of successful methods for liquid surface tension, or energy, measurement based upon surface deformation. This happy state of affairs does not, however, extend to solids, which are considered to possess surface energies for the same reasons as do liquids, i.e. because of unsaturated ionic bonds at the solid gas interface. As in the case of the flotation cell producing surface on liquids as new bubbles, it takes energy to produce new surface on solids as new particles. As every mill man knows, this surface is produced on mineral solids in a grinding mill by the action of a tumbling mass of iron balls. But here so much energy usually is wasted by the inefficient action of these balls that a large amount of heat is generated, and the surface energy production may be easily confused with the energy necessary to produce this ineffective heat. The tumbling balls and fracturing minerals ultimately take their energy from a rather large electric motor. It has been variously estimated that from 10 to 20 pct" only of this energy from the motor does not appear as heat and may be presumed to appear as surface energy on the minerals present.. Such a production of new surface on the mineral phases is accompanied, of course, by a size reduction that is inevitable as more and more mineral interior molecules become surface molecules by the fracture exposure. This size reduction of mineral particles, although the most obvious feature and perhaps the sole object of the milling operation, is from this energy viewpoint the outward manifestation of the production of surface energy only. Measurement of the characteristic surface energies of pure minerals and their various mixtures in ores would be a step towards understanding of the energetics of the commercial grinding operation. In addition, the characteristic surface energy of a mineral is probably a physical property specific for that mineral, and therefore, from a scientific standpoint, should be measured. It is interesting to note that, in contrast to the large body of work on the surface tensions of liquid systems and biological systems, the field of solid surface energies has been neglected. Prior to. 1920 it is difficult to find more than one or two references to work on solid surface energies in Chemical Abstracts. Since 1920 such references number somewhat less than 100, while those on liquid systems are numbered in the thousands. Much of this apparent neglect of the field of solid surface energies (the term is intended to be somewhat inclusive at this point and refers both to the solid: gas, and the solid: liquid interface) is because of the lack of a reliable method of measurement rather than any lack of scientific curiosity. It was, and still is, difficult to produce new surface on a solid without the simultaneous production of interior changes in the same solid which may consume part of the energy used. The extension in the surface area can be measured, but the interior crystal-

Jan 1, 1952

By H. C. Fuller

This paper discusses 105 production runs at Boulder City, Nev., in which titanium metal was made in 200-pound batches. It describes the equipment and techniques used in preparing raw material, the reduction process, and the removal of the reaction mass from the reaction vessel. Also, some data on man-hour requirements are presented. The main emphasis was on producing ductile-grade titanium and developing a standard procedure for obtaining a consistently pure product. Some departures from techniques used before were found to be desirable. The most important of these was the use of a sealed room with a controlled dry atmosphere in which the reaction vessel was opened and the reaction mass removed. This minimized the moisture taken up by the magnesium chloride in the reaction mass, and it could be purified successfully by vacuum distillation. Using the dry room also made it possible to leave al-inch shell of the reaction material on the walls of the vessel, which lowered the iron contamination and eliminated the labor and time-consuming job of cleaning the vessel after each reduction. Another change was lowering of the temperature during reduction to 750° C. instead of 850° C. This was found to give good results more consistently. The first poke to break the crust during reduction was eliminated, as it was found to be unnecessary and only added more work and was another possible way of introducing air. A rotating feed arm was installed in the reaction vessel to distribute the titanium tetrachloride over a larger area and, thus, prevent local overheating. The process, conducted in a batchwise manner as described and followed by good purification and fusion, produces a metal adequate in quality for nearly all purposes.

Jan 1, 1952

Nippissing Mines Co., Ltd., a Ventures subsidiary, has bought into the, Vermont Copper Co. Inc. which operates a copper mine in Vermont producing 700 tons daily. The Vermont Mining Co. has been in operation since 1943 under the present management. When present owners wanted to convert their holdings to cash, the Ventures people saw possibilities in the area which, has been little explored but has a sizable production record. Final approval of the Anaconda-Harvey project for a 72,000 ton aluminum reduction plant at Kalispell, Mont., has been announced by Defense Production Administration. After considerable discussion in the past few weeks regarding Anaconda's entrance into the aluminum field, the approval stated "clearly the best arrangement."

Jan 1, 1952

By R. R. Wells

As a part of the strategic mineral program, examining engineers of the Bureau of Mines collected samples several manganese properties in Colorado. As all of the ores were too low-grade to be acceptable to manufacturers of ferromanganese, beneficiation studies were required .to determine the amenability of the ores to concentration. Manganese in the form of impregnations in sedimentary beds is found in the Denver plains area a few miles east of the Rocky Mountain front. Deposits are reported to occur intermittently over a distance of more than 200 miles. The manganese oxides occur in beds of conglomerate or arkosic sand, generally accompanied by limonite. The Manganese and iron oxides,, however, usually are found in separate layers. Three samples were submitted for beneficiation tests, two samples from Buckley Field bombing Yang, Arapahoe County, and one from near Franktown, Douglas County.

Jan 1, 1952

By Robert Glass Cleland

[Incorporated under the laws of the State of New York OFFICE, 41) WALL STREET, NEW YORK 5, N. Y. Authorized4,000,000 shares $150,000,000.00 Outstanding-5,071,260 shares 126,781,500.00]

Jan 1, 1952

By E. C. Harder

CERTAIN typical characteristics of bauxites, ores of aluminum permit their classification into a number of categories, each of which has special features that enable grouping within it deposits from widely scattered bauxite fields. There may be local variations in conditions that have introduced differences of lesser importance between similar deposits in different fields, resulting perhaps from the influence of factors other than those that have produced the distinguishing features of each of the different groups, but in general the similarity between the deposits in each group is sufficiently striking to make the grouping indicated of interest. Several factors and conditions enter into the decomposition process that results in the development of bauxites and laterites and affects their character. The principal conditions favoring optimum bauxitization are: (1) pres- ence of rocks with easily soluble minerals yielding residues rich in alumina; (2) effective rock porosity, enabling easy access and free circulation of water; (3) normal to abundant rainfall alternating with dry periods; (4) vegetation, including bacteria, advantageously distributed; (5) available sources of appropriate solution and precipitation agencies; (6) a tropical or at least a warm climate; (7) low to moderate topographic relief, allowing free movement of the water table but a minimum of erosion; and (8) long quiet periods in earth history. Assuming that all of these factors are operating to a greater or less degree, it seems that the one that affects most the physical character of the resulting bauxite or laterite deposits is the chemical and mineralogical composition of the rocks that by their decay yield the bauxite deposits. This factor is used in the classification followed in this paper. In the process of weathering of ordinary silicate and carbonate rocks of the earth's crust, whether of igneous or sedimentary origin, it is the minerals of the alkalies that yield most readily to attack. The alkaline earth compounds also offer no great resistance, particularly the carbonates. Thus, among the rock-forming elements, those producing the most insoluble compounds are aluminum, iron, and silicon, together with certain ones of less importance, such as titanium, manganese, and phosphorus. In normal weathering processes such as prevail in temperate regions, the common minerals of rock decay are

Jan 1, 1952

By Strathmore R. B. Cooke, William F. Stowasser

RESULTS presented in a previous paper1 have shown that the strength of fired pellets made from eastern Mesabi magnetite concentrates containing 8 to 9 pct Si02 as quartz and silicates is due to several processes which occur during firing. These are: l-recrystallization and cementation of the fragmented magnetite grains; 2-formation of slag from reaction between the quartz, silicates, and available ferrous iron, followed by slag-bonding of the magnetite grains; and 3-oxidation of the magnetite to hematite and subsequent recrystallization and grain growth of this constituent. Microscopic examination of all magnetite pellets fired in one operation in small and large-scale pilot plant furnaces and possessing normal strengths shows that the processes 1,2, and 3 have taken place; where strengths are low and the pellets are otherwise sub- normal, one or more of the processes has not occurred. For example, soft and friable red pellets may contain a central core of slag-bonded recrystallized magnetite which is strong enough in itself, but the shell contains only slightly recrystallized hematite, indicating that the maximum temperature reached was too low. Processes 1 and 2 can occur only under reducing conditions, as for example, when coal is intention- ally added to the original pellets; under neutral conditions, when pellets are fired in an inert atmosphere; or when pellets are brought so rapidly to temperature in an oxidizing atmosphere that oxygen diffusion to the core lags behind the recrystallization and slagging effects. This last-mentioned process has occurred in all pilot-plant shaft fur-

Jan 1, 1952

Year Institute of Metals ? Petroleum - Iron and Steel ? Coal ? Mineral Industry Education - Industrial Minerals 1918 W M CORSE 1919 1920 W H BASSETT 1921 1922 W B PRICE 1923 E DEGOLYER 1924 G K ELLIOTT 1925 F JULIUS FOHS 1926 PAUL D MERICA 1927 JOHN M LOVEJOY 1928 S SKOWRONSKI A W AMBROSE RALPH H SWEETSER 1929 J B UMPLEBY G B WATERHOLSE 1930 ZAY JEFFRIES C V MILLIKAN W J MACKENZIEHOWARD N EAVENSON 1931 SAM TOUR C E BEECHER F M BECKET 1932 C H MATHEWSON EARL OLIVER F N SPELLERTHOMAS G FEAR C H FULTON

Jan 1, 1952

Dump Truck Kenworth Motor Truck Corp. is beginning full scale production of its new heavy-duty, end-dump earth mover, model 801, a truck engineered for earth moving under the most adverse operating conditions. Payload capacity of the Kenworth earthmover is 30,000 lb and it is over-tired for safety, flotation and high tire life. The truck's body capacity, struck measure, is 9.9 cu yd, with heaped [ ] load at 11.9 cu yd. The earth-mover has a full anti-friction bearing mounted, power assisted steering gear, simplified controls, minimum turning radius and wide axle track to insure ease of handling, maximum maneuverability and high stability. The offset cab of the Kenworth visibility for the driver, before and after. Circle No. 1 Safety Equipment A compact, safe, and efficient valve assembly approved by the United States Bureau of Mines for use with MSA air line respirators, abrasive masks, and abrasive helmets has been developed by Mine Safety Appliances Co. The new MSA continuous air flow control valve regulates air flow from a compressed air source to an operator using respiratory protective air line equipment. Three parts-a centridge container, a cartridge and the air flow check valve-comprise the entire assembly of the control valve. A position action adjustment knob on the cartridge container regulates the amount of air flowing to the operator. The valve can be detached from the air line instantly by pressing the trigger on the cartridge container near the check valve. As the trigger detaches the hose, the spring loaded ball-type valve, which is attached to the end of the hose, automatically stops the flow of air. Circle No. 2

Jan 1, 1952

Establishment of a Bureau of Mineral Research at the Michigan College of Mining and Technology, initiated by the State of Michigan with legislation in 1951, is moving toward realization. The Michigan Legislature appropriated $24,000 to cover preliminary costs of plans and specifications for "engaging in a broad, widespread study of the beneficiation of lowgrade ores, of ore dressing, and all the problems of metallurgy that enter into such a program." Ralph C. Calder, of Detroit, who designed Michigan Tech's campus buildings, is preparing plans for the proposed Ores Research Building. Members of the college staff, Professors F. J. Tolonen, W. E. Keck, and Research Engineer Paul Jasberg are assisting in preliminary planning. C. Harry Benedict, retired chief metallurgist of Calumet and Hecla and a member of Michigan Tech's Board of Control, is assisting with technical details. Professor Nicholas Manderfield, head of the department of Mineral Dressing, was assigned to visit other research installations and suggest plans for the Bureau.

Jan 1, 1952

By LeRoy Scharon

EACH year it becomes apparent that geophysical activities in the fields of mining and engineering are increasing in the number and variety of applications. Many mining companies are including, as part of their exploration programs, geophysical surveys. The value of geophysics in highway and structural foundation investigations has been realized and is now an important part of subsurface investigations in conjunction with soil and rock borings. United States of America One of the major orebody discoveries of the year is that of the Grace mine near Morgantown in Berks County, Pa. This orebody, now under development by the Bethlehem Steel Co., was discovered by an airborne magnetometer survey carried out by the Aero Service Corp. of Philadelphia. The orebody, the geological occurrence of which is similar to those existing at Cornwall, Pa., was found at a depth of 1500 ft under a cover of Triassic sediments and is reported to have a reserve of well over 100 million tons. Shaft sinking and other construction work has started at the site. Resistivity work was carried out at proposed dam sites in New York and in connection with the search for fluorspar veins in Kentucky. Spontaneous polarization investigations were pursued in the Appalachian region at various localities from North Caro¬lina up into Virginia. This work was done in connection with the search for sulphide-bearing structures. Several indications were proven by subsequent drilling to correspond to unknown sulphide deposits, a few of these occurring in the vicinity of properties long under exploitation. Refraction seismic methods applied to bedrock depth determinations as related to water problems on the Marquette Range and the extension of the. regional gravity survey on the Menominee Range to learn the major structural features of the area have been reported by, Lloyal O. Bacon. A gravity survey has been completed in the vicinity of Tioga, Bradford County, Pa. with a gravity profile being observed from Tioga east to the Delaware basin. The Indiana Geological Survey is concerned with a state-wide gravity survey. Judson Mead, University of Indiana, reports that the bulk of the State Survey's geophysical work, however, has been "seismic refraction work in connection with drift thickness problems. The survey has made almost 1000 determinations in areas of moderately thick drift. The results of this work are of interest to both the coal mining industry and to the stone industry." In the southeastern Missouri lead belt, magnetic electrical resistivity, and electromagnetic applications for the discovery of new lead deposits have been used with success. A gravity survey of the residual-barite deposits in Washington County, Mo., was made during the summer season with preliminary computations of tonnages checking with tonnages mined. Robert M. Dryer, of the University of Kansas has had considerable success in mapping structural features in southwestern Kansas with the gravity meter and is now engaged in tracing shoestring sands in eastern Kansas by resistivity surveys. Several, foundation sites were investigated in greater St. Louis using electrical resistivity and seismic refraction methods with success. A minimum amount of drilling data was available for checking and interpreting the geophysical results (Fig. 1). It is to be noted that geophysical methods are finding a place in subsurface investigations for highway and foundation problems. Interest has been so keen in this field that the American Society for Testing Materials, at its annual meeting in June of this year, devoted one session of its symposium on surface and subsurface reconnaissance to geophysical papers involving the application of the electrical resistivity and seismic refraction methods to subsurface studies. At least three major mining companies in the United States have entered the field recently in geochemistry. The program of research and development of geochemical techniques by the U. S. Geological Survey continues. Experimental field projects were conducted over lead-silver, cobalt, copper and zinc deposits in Idaho, Oregon, California, Wisconsin and Montana. Similar experiments were carried on by M. P. Nackowski in the Illinois-Kentucky fluorspar district and in the Tri-State Zinc district by R. Maurice Tripp with favorable results. Geophysical activities of the U. S. Geological Survey for 1951 were extensive and varied. About 21,000 miles of airborne magnetic and 10,000 miles of airborne radioactivity traverse were flown in 1951 by the U. S. Geological Survey. A total of 35,000 miles of aeromagnetic traverse were compiled, 57 aeromagnetic maps were published and 14 preliminary maps were placed on open file. Airborne surveys were made in Aroostook County, in the Katahdin and Dead River areas in Maine; in northwest Washington; over the Mother Lode district in California; in northeastern and northwestern Minnesota; and in the New York-New Jersey highlands. Of special interest were the surveys in Washington, where highly magnetic Eocene lavas gave information on structures in the overlying Miocene sedimentary rocks and in northeastern Minnesota over the Duluth gabbro. The latter survey was made following the discovery of nickel-copper mineralization in the gabbro near its contact with the Virginia slate. The principal ground geophysical surveys for metalliferous deposits and related purposes were made in the Colorado Plateau region, where electrical surveys assisted in prospecting; in Aroostook County, Maine, where ground magnetic surveys, following aeromagnetic surveys, have permitted tracing

Jan 1, 1952

By R. B. Full

DURING the summer of 1949, the United Nations Scientific Conference on the Conservation and Utilization of Resources met at Lake Success. As summed up by one writer, the purpose was: "That everyone will try to learn how to feed more people from an acre of land." That objective is a stimulus to the phosphate rock industry as well as other industries. Phosphate rock was mined first in the Canadian province of Quebec where it was found as an apatite in pockets. In 1863, mining began near the Rideau Canal, first in open trenches and quarries until shafts were sunk. These operations were difficult since hard rock had to be drilled and blasted. Steam was the source of power. The phosphate rock was hand-selected and recovery ranged from 6 to 10 pct, averaging 70 pct to 85 pct bpl (bone phosphate of lime). Costs, f.O.b. Montreal, were $14 a ton, and selling prices averaged $17 a ton. In 1885, about 29,-000 tons were sold on this basis, but by 1892 the output fell to 8000 tons at an average price of $15 a ton at Montreal. South Carolina Deposits Phosphate rock was first discovered in South Carolina in 1837, but a mining company was not formed until 1867. It was immediately successful, and the industry continued to develop and ship an increased tonnage of land and river rock, shipments increasing from approximately 20,000 tons in 1868 to 537,000 tons in 1890, when the shipments began to decrease. In 1892 only 350,000 tons were shipped. In this field there were two types of deposits: land rock and river rock. More land rock tonnage was mined until about 1887 when river rock production began to equal it. The land rock was mined adjacent to and in the river marshes by pick, shovel, and wheelbarrow. Each worker dug daily a space 6 ft wide, 15 ft long and 6 ft deep, which was overburden, and then loaded about 3 cu yd of phosphate rock into wheelbarrows. His helper would wheel the barrows to small steam railroads up to 250 ft distant. Water was kept from the pits by steam pumps connected to railway cars. The phosphate rock was loaded into railroad cars, hauled and dumped into a log washer to which water was added, and run over trommel screens to eliminate the clay and loose sand. Steam shovels for loading were introduced about 1891. River rock was mined by floating dipper dredges and at low tide was loaded into barges by laborers using oyster tongs, the large lumps being hand-loaded. Barges and bateaus were unloaded by wheelbarrows which were wheeled to the same type of land rock washers. The washer product was piled with stacked pine cordwood in alternate layers and fired for drying. Usually this was done under sheds along the river bank. The dried rock then was transferred to ships, usually three or four-masted schooners. Cost of production of both land and river rock, including $1 a ton royalty paid to the state for state-owned property, was approximately $4.25 a ton averaging 60 pct bpl. The selling price was approximately $7 a ton f.O.b. In 1886 the courts handed down a decision permitting anyone to mine, and many additional companies were organized immediately. As a result, the selling price was lowered to a profit margin of 50Ø or less per ton. The South Carolina mines were eventually shut down when a more profitable source of phosphate rock was discovered in Florida. Florida Deposits Phosphate rock was discovered in Florida in 1882, and in 1883 a small quarry was opened near Hawthorne. In 1886 phosphate rock of good grade was discovered on Peace River, and the Arcadia Phosphate Co. was formed. In 1888 the company began shipments amounting to 3000 tons that year. During the latter part of 1888, hard-rock phosphate was discovered near Dunnellon. Exploration extended rapidly, and deposits of hard-rock phosphate were mined over a wide area so that shortly after 1900

Jan 1, 1952

THE following employment items are mode available to AIME members on a nonprofit basis by the Engineering Societies Personnel Service, Inc., operating in cooperation with the Four Founder Societies. Local offices of, the Personnel Service are at 8 W. 40th St., New York 18; 100 Farnsworth Ave., Detroit; 57 Post St., San Francisco; 84 E. Randolph St., Chicago 1. Applicants should address all mail to the proper key numbers in care of the New York office and include 6c in stamps for forwarding and returning application. The applicant agrees, if placed in a position by means of the Service, to pay the placement fee listed by the Service. AIME members may secure a weekly bulletin of positions available for $3.50 a quarter, $12 a year. POSITIONS OPEN Mining Engineer with some engineering training, capable of doing mapping, surveying, exploration, geology and transit work. Location, New York State. Y7333. Mineral Dressing Engineer, B.S. Mining or Chemical Engineering, age to 35. Must have knowledge of flotation. Duties will be in applied research and field evaluation of cationic and anionic flotation agents. Salary, $3500 to $7000 depending on experience. Location, Chicago. R-8971. Geological Draftsman, 25 to 30, with some experience in working with a geologist. Salary, $5100 a year. Location, New York, N. Y. Y7153.

Jan 1, 1952