Search Documents

By J. H. Jackson, R. B. Fischer

VERY little is known about the properties of relatively pure refractory metals in the cast state since these metals are customarily made by powder-metallurgy methods. Recently, the development of the vacuum arc-melting furnace has made possible the study of large, sound ingots of cast molybdenum. The ductility of molybdenum, at room temperature, may vary considerably. Often the brittle state depreciates the utility of molybdenum, even for the material prepared by powder-metallurgy techniques. At the outset of this program, it was felt that if the causes of brittleness were to be determined it might be possible to reduce the difficulties met in the working of molybdenum. Also, the problem of producing strong, fusion weldrnents of molybdenum might be solved. The conditions required to produce ductile molybdenum by the powder-metallurgy technique are reasonably well known. A fibrous or elongated-grain structure has good ductility although this property is probably directional. The equiaxed structure obtained in fully recrystallized molybdenum has been considered to be brittle. The reasons for this behavior of molybdenum have not been established. The preparation of cast molybdenum ingots by the vacuum-arc method was described by Parke and Ham.' By this method, ingots weighing up to 250 Ib were produced." Parke and Ham1 found that molybdenum ingots containing more than approximately 0.0025 pct oxygen could not be hot forged. On the other hand, they found that fully deoxidized cast molybdenum, containing up to 0.06 pct carbon, could be hot forged. However, the as-cast ingots containing either carbon or oxygen were brittle at room temperature. Parke and Ham,1 Woodside,3 and Zapffe, Landgraf, and Worden4 noted the inter-granular precipitation of oxide or carbide in cast molybdenum. This study—part of an extensive program on mo-lybdenum—had the following objectives: (1) To investigate the causes for the brittleness of cast molybdenum at room temperature, (2) to investigate the means for improving the ductility of cast molybdenum at room temperature, and (3) to add to the knowledge of cast molybdenum and of cast metals in general.

Jan 1, 1951

By William L. Crentz

In the past, Westmoreland County together with Fayette County produced about one-third of the bituminous coal mined in Pennsylvania. The Pittsburgh bed in Westmoreland County has furnished enormous quantities of coal to the by-product and beehive ovens, gas-manufacturing plants, and general industrial manufacturers over a wide area until about 20 years ago. Little attention was paid to the thinner beds because of the superior quality of the Pittsburgh. The approaching exhaustion of Pittsburgh coal will require accelerated-exploitation of these coals if Westmoreland County is to continue as an important source of bituminous coal, Much of the Pittsburgh coal in Westmoreland County is low-sulfur and requires no mechanical cleaning for the preparation of a metallurgical fuel. Even those areas where the sulfur percentage increased to a maximum of about 2 percent, a relatively easy washing operation usually produced a cleaned coal, which found ready acceptance by the coke industry. Davis reported the remaining recoverable reserves of the .Pittsburgh bed in Westmoreland County to be 255,439,000 tons as of January 1, 1937. Since that date, more than 100,000,000 tons of Pittsburgh coal has been extracted so that the time is not too distant when this important coal bed will be depleted. A study of the Pittsburgh bed in Westmoreland -County has not been made a part of this report as the remaining reserves of the coal can be used in coke making with a, minimum of preparation. The production from the Upper 'Freeport bed will increase as the supply of coal from the Pittsburgh bed diminishes, and as of the present time it supplies a substantial proportion of the county's coal output.

Jan 1, 1951

By T. E. Purcell

(a) Moisture. - Moisture, "as fired," is specifically significant in pulverized-coal firing because of its effect upon the continuity of raw-coal feed to the pulverizer, pulverizer capacity, flame stability, and speed of ignition. The extraneous moisture content is a rough index of potential difficulties in unloading and maintaining the flow of raw coal to the pulverizer and of pulverized coal to the furnace, with the troubles increasing geometrically as the percentage increases. Sticking or other stoppage of coal flow at any point between the bunker and the furnace is especially serious with pulverized-coal firing because there is danger of immediate loss of output. Where moisture is a problem, the designer must exercise great care in the design of coal-handling and preparation apparatus.

Jan 1, 1951

By Walter E. Lewis

The Fort Randall Reservoir project, on the Missouri River at Pickstown, S. Dak., was designed by the Corps of Engineers and is part of the Missouri River Basin Development Program. The location of the project with respect to adjacent features is shown' in figure 1. When the project is finished, it will include a large earthwork dam and 12 circular tunnels, 8 of which will be equipped for power and 4 for flood control. Various phases of the construction have been contracted to independent companies, and at present four companies are working on different phases of the project under a rigid time schedule. Western Contracting Corp. is the contractor on stage II, earthwork; Johnson-Winston Construction Co. is the contractor for construction of the intake towers at the upstream side of the dam; McCarthy Improvement Co. has the contract for the power house and the outlet works on the downstream side; and Silas Mason Co. has the contract for driving the power and flood-control tunnels. The latter two companies use the same roads for ingress and egress to their respective work areas and the same general waste dump area. Under such circumstances, it is necessary that each company stay on a time schedule in regular sequence to avoid interference with the other.

Jan 1, 1951

By B. F. Decker, D. Harker

The recrystallization reaction in OFHC and spectroscopically pure copper has been followed by X ray diffraction determinations of the amount of material with the cold-worked and recrystallized textures in specimens which had been given various heat treatments. The heats of activation for recrystallization are found to be: 29.9 kcal per rnol for OFHC copper and 22.4 kcal per rnol for spectroscopic copper. A reliable and speedy method for measuring the amount of recrystallized material in a piece of rolled metal, together with a new scheme for low temperature heat treatment, have made possible a determination of the activation energy for recrystallization in rolled copper. This method for studying recrystallization rates is different from others reported in the literature.' Oxygen free, high conductivity copper—OFHC copper—of purity 99.98 pct gave an activation energy for recrystallization of 29.9 kcal per mol with recrystallization data taken in the temperature range 208-245°C. Copper of purity 99.999 pct from the American Smelting & Refining Co. gave an activation energy for recrystallization of 22.4 kcal per mol with recrystallization data taken in the temperature range 43-135°C. The great change in activation energy for recrystallization as the small amount of impurity in the metal is decreased suggests that the motion of grain boundaries is conditioned by the impurities which must be concentrated in them. Thus the OFHC copper recrystallizes with an activation energy of the order of magnitude to be expected for the diffusion of the kind of impurities likely to be present. The high purity copper, on the other hand, recrystallizes with a much lower activation energy, in accord with the notion that the grain boundaries need not wait for the impurities to diffuse with them. Copper when strongly cold-rolled has a well-defined crystallite texture which can be described by saying that the [111] direction of the face- centered cubic crystals is aligned approximately in the cross-rolling direction and that faces of the form {110} lie approximately in the rolling plane. When such rolled copper is completely annealed the crystallite texture is quite different: the [loo] direction is in the cross-rolling direction and faces of the form (100) are in the rolling plane. At intermediate stages of annealing, the copper contains both textures. If a Geiger counter X ray diffraction spectrometer is set up so as to measure the intensity of the (200) Bragg reflection from the rolled surface of a piece of copper strip, this intensity increases from a very small value in the cold-worked state to a maximum as the specimen is annealed. The same would be true for (200) reflections from planes normal to the rolling or cross-rolling directions. In view of this fact, the amount of material in the copper which has recrystallized can be measured by comparing the intensities of one of these reflections just mentioned with the intensity from a similar specimen after complete annealing. In much the same way the intensity of (111) reflections from planes normal to the cross-rolling direction could be used to measure the amount of unrecrystallized material in the specimen. In the work to be described here the amounts of recrystallized and unrecrystallized material in partly annealed rolled copper specimens were determined in this way. Experimental Procedure Samples of oxygen free high conductivity (OFHC) copper, cold-rolled 99.7 pct to 0.002 in. thickness, were subjected to heat treatments for various chosen times at four different temperatures, and high purity copper samples, cold-rolled 98.0 pct to 0.0015 in. thickness, at six different temperatures. Each sample, after treatment, was placed in an orientation sample holder for use with a Geiger counter X ray spectrometer and a reading was taken of the intensity of the (200) reflection from planes perpendicular to

Jan 1, 1951

By John W. Buch

In 1947, a Korfmann universal shearing machine was installed in a mine in the Southern field of the Pennsylvania anthracite region. The machine was obtained from Germany by the Bureau of Mines after the close of World War II as a part of a program of experimental work to increase the output and lower the cost of anthracite, which the Bureau of Mines initiated in 1944 when an agreement was made with an anthracite-producing company for use of one of the company's mines as a testing ground for certain mechanical equipment procured or developed by the Bureau. A major objective is to develop a mechanical mining method that will increase the rate of advance and reduce the coat of development of coal gangways in steeply pitching seams. In addition to the time to be saved in driving these openings by machine, it is felt that further economies will be affected by making it possible to concentrate producing sections into smaller compass and that savings will ensue in supervision, maintenance, and time required for mining a section. A higher percentage extraction also is an objective. Test work covered by this report was concentrated on the power characteristics, maneuverability, effectiveness, and general qualities of the Korfmann machine in cutting coal, the cutting tests representing the first use of a machine of this kind in steep-pitch mining in the United States.

Jan 1, 1951

By A. L. Engel

This report is a compilation of results of brief preliminary tests on sulfide ores that contained gold and silver and, in some cases base metals. It is a companion paper to a recent similar report on oxide ores. Simple treatment methods employing the least possible equipment sometimes produce satisfactory results on marginal ores and in small-scale operations. Investigations of typical ores from newly discovered or recently explored mining districts have been made in continuation of a long-established part of the hydrometallurgical and ore-dressing program of the Reno station, Bureau of Mines. The purpose of such investigations is to encourage the search for and development of mineral resources and particularly to assist in the economical exploitation of low-grade and marginal ores as well as the conservation and recovery .of values in products that were discarded from former operations because of inability to treat them profitably. Several of these investigations have been limited to preliminary tests of samples from prospecting operations, whereas same involved samples of old dumps or tailings piles. The test work in these cases was not extensive enough to warrant publication as individual reports, but is of considerable interest inasmuch as it indicates the possibilities as well as the limitations of treating the respective materials. The samples were representative of the districts from which they wore obtained, so this information should be helpful in the future development of these districts.

Jan 1, 1951

Jan 1, 1951

By F. S. Turneaure, R. Gibson

The tin deposit of Monserrat, Bolivia, consists of one major vein 1600 m in length. The ore is unusual because of the notable quantity of teallite, even though cassiterite is the principal tin mineral. The deposit, formed at shallow depth under a wide range in temperature, may be classed as xenothermal. Polished sections reveal a complex history of replacement, with low-temperature minerals deposited before high-temperature minerals. THE Monserrat mine1'2 of the Compania Minera Monserrat is located 11 km east of Callipampa, a station on the Antofagasta and Bolivia Railway some 55 km south of Oruro. The mine lies in a group of low hills on the east slope of a broad valley of northerly trend. The valley is separated from the altiplano to the west by a prominent ridge that rises several hundred meters above the surrounding country (fig. 1). Callipampa is situated a short distance west of the ridge, near the east margin of the altiplano. The elevation at Callipampa is 3700 m and at the mine 4100 m. Monserrat is near the northeast limit of what may be called the Poopo-Pazna district, an area of northwesterly trend about 25 km in length and 15 km in width. The district includes the tin-silver prospects of Poopo to the north, the zinc-tin deposits of Salvador to the southwest, and the tin-tourmaline veins of Avicaya to the south. Along the prominent ridge already mentioned, which forms the western limit of the district, there are several tin and antimony prospects including the Trinacria mine, which is famous for its fine specimens of cylindrite. Although the principal ore mineral is cassiterite, the tin deposit of Monserrat contains an unusual amount of teallite. Cassiterite occurs in part as a finely granular mixture with sulphides of iron and zinc and in part as needle tin of late hypogene age. The regional structure is dominated by broad folds typical of the Andes of Central Bolivia and similar to those of the Llallagua district. The area adjacent to the Monserrat mine is underlain by thin-bedded shale somewhat variable in color but predominantly dark grey to black. The beds strike northwest and dip at low angles southwest, forming part of the northeast limb of a major syncline. A resistant sandstone formation, which underlies the black shale, crops out along a ridge east of the mine and also accounts for the high ridge to the west that was previously mentioned. No igneous rock of any kind is found at Monserrat. The nearest intrusive bodies known are the irregular dikes and masses of quartz porphyry at Avicaya about 10 km to the south. Mine Workings The Monserrat property includes one main vein, which can be followed on the surface for 1600 m, and two or three branch veins of distinctly minor importance. The principal haulage tunnel, referred to as the San Carlos adit or level III, extends northeasterly for 1700 m, following the main vein throughout most of this distance. Above the adit, there are

Jan 1, 1951

By M. H. Caron

THE most outstanding property of ammonia liquors, used in the ammonia leaching process is their very limited ability to dissolve all compounds present in reduced ore except nickel and cobalt. Although they do have such a high degree of purity, even the smallest amounts of impurities contaminate the precipitate of basic nickel carbonate that may be obtained from pregnant liquors by straight distillation. Figures have been given in a separate paper regarding the extent of such contamination. The product of straight distillation is likely to contain small amounts of Fe, Mn, MgO and SiO2 as well as some sulphate and sulphide. The sulphur can be readily eliminated by calcination of the product at the proper temperature and MgO and SiO2 by reduction and melting of the metal with a suitable flux. After such treatment the metal is relatively pure, and the iron and manganese content will be very small. The cobalt content, however, may vary considerably, depending upon the ore treated. The metal obtained from pure true garni-erite ores usually has only a small cobalt content of less than 1 pct. Metal obtained from medium grade iron-rich nickel ores may show cobalt values from 2 to 3 pct, and the alloy obtained from laterite is likely to contain as much as 10 pct cobalt. By proper treatment a good deal of cobalt may be recovered from lateritic nickeliferous iron ores, and cobalt will become the major constituent of the pregnant liquor if asbolan ores or similar products are treated. The pregnant liquor of "run of mine" nickel ores may have a pinkish shade, indicating the presence of cobalt. It is evident that from such liquors the metals should be recovered separately. Even if cobalt is present in only very small amounts, it would probably be economically justifiable to recover both metals as pure as possible if a suitable process could be devised. The author has made investigations along this line and has patented some processes adapted to the treatment of this type of solutions. Selective Dissolution of Nickel from Basic Nickel Carbonate Containing Some Cobalt: Basic nickel carbonate obtained from true garnierite ores by straight distillation of the pregnant liquors, always contains some cobalt as well as the normal impurities. In. order to improve the quality of the nickel product and to recover most of the cobalt, the following process has been devised. By using liquors with a low CO2 to NH3 ratio, nickel can be redis-solved preferentially to cobalt. It is not a sharp and clean separation but a selective one, for the bulk of the nickel may be redissolved with a small amount of cobalt, and a small residue may hold the bulk of the cobalt. The greatly increased cobalt content of the residue is indicated by a pronounced olive green color, in contrast with the light green color of pure basic nickel carbonate. The following example is given from Dutch patent No. 52788, Klasse 40a. 43 granted June 17, 1942: The original precipitate contained about 0.55 pct cobalt calculated on total nickel + cobalt. Eight hundred and fifty grams of the basic nickel carbonate were redissolved in leach liquor containing 7.12 pct NH3 and 2.12 pct CO2. The weight of the dry residue was about 3.5 pct of the original weight. By analysis it was found that the residue contained: Fe 1.93 pct, Co 6.01 pct, Ni 34.87 pct and also a certain amount of silica. The clear filtered blue liquor was distilled and the precipitate of basic nickel carbonate from this analyzed: Fe 0.008 pct, Co 0.0146 pct, Ni 42.37 pct. It is obvious that this product is considerably more pure, since calculation shows that about 94 pct of the original cobalt remained in the residue. Cobalt and nickel can be recovered by further

Jan 1, 1951

By F. W. Bloecher, A. M. Gaudin

H. H. Kellogg—There is one point that the author has failed to emphasize sufficiently in his paper. What is commonly called the equilibrium contact-angle (the author's "maximum contact-angle") can have only one value on a smooth, flat, homogeneous surface under a given set of conditions. The equilibrium contact-angle is defined, for such a system, as the angle between the solid-liquid and liquid-gas interfaces, measured through the liquid. The value of the equilibrium contact-angle is uniquely determined by the value of the interfacial energies of the three intersecting interfaces and is independent of other forces in the system. When the liquid-gas interface intersects the solid at an edge—as was the case for all the experiments reported in this paper—the orientation of the solid-liquid interface is indeterminate or varies through 90" for a right-angle edge. Mr. Morris has called the angle between the horizontal and the liquid-gas interface for this edge condition a "static contact-angle." I feel that this term is unnecessarily misleading. In the first place, "static contact-angle" sounds too much like "equilibrium contact-angle." In the second place, the magnitude of the "static contact-angle," which I would prefer to call the "supporting angle," is determined by the forces in the system other than those derived from the interfacial energies, hence "contact angle" is misleading. If Mr. Morris had said that the "supporting-angle" is variable and depends on the weight of the particle and size of the bubble and that it has a maximum possible value equal to the equilibrium contact-angle, his discussion would have been more accurate. T. M. Morris (author's reply)—Mr. Kellogg puts forth a reasonable criticism of some of the terminology used in the paper. I agree that the term "static contact angle" may be misleading. Substitution of the term "supporting angle" or "vector angle" may be more suitable. F. X. Tartaron—In this paper the author presents a very interesting mathematical development of the forces present when a mineral particle adheres to an air bubble. Excellent concordance is obtained between mathematical formulation and experimental results. It is the writer's understanding that when the mineral surface presented to an air bubble is greater than the area of contact, the maximum contact angle is obtained. However, this contact angle represents distortion of the bubble, the normal shape of which is spherical or in cross-section, circular. This distortion produces a force that acts in opposition to the force of adhesion between the bubble and particle. Hence, at maximum contact angle, the force of adhesion between bubble and particle is at a minimum for static conditions. However, when the size of bubble is increased, the size of particle remaining the same (and all other conditions remaining the same), the contact angle decreases, the distortion of the bubble decreases and the force in opposition to adherence of bubble and particle also decreases. Thus, there is stronger attachment between bubble and particle. When this situation is applied to actual flotation conditions, it is doubtful that it has any significance. The reason is that the bubbles are normally so much larger than the particles, that in substantially all cases, it is probable that negligible distortion of the bubble takes place. In table IV, the author makes computations for bubbles from 0.50 to 2 mm diam. This is from 0.02 in. to 0.08 in. Certainly the bubbles generated in a flotation machine are far larger than this. The surfaces of the author's bubbles range from 0.79 to 12.6 sq mm. The area of contact of the glass rod (0.15 mm diam) is 0.017 sq mm. Thus, ratio of bubble surface to mineral area of contact ranges from 47 to 741 in round numbers. If we take a %-in. diam bubble and a 65-mesh (0.208 mm) particle of cubical shape, the ratio of bubble surface to mineral area of contact is 2931. Mineral particles do not readily become attached to air bubbles. Taggart has shown that in pneumatic flotation machines collector-coated particles are only temporarily attached to bubbles. They keep falling off and down in the froth but at a delayed rate as compared with gangue. Spedden and Hannan's motion pictures confirm the difficulty of attaching particles to air bubbles. In the agitation froth process, according to Taggart, air is precipitated from the water selectively on to the collector-coated particles and these

Jan 1, 1951

By R. R. Estill

THE rank of the Ruhr coal ranges from a high volatile bituminous coal to an anthracite, depending to some extent on the original depth of the seam. The average Ruhr coal corresponds to a soft bituminous American coal of a coking quality. The average thicknesses of individual coal seams being mined are also comparable (59 in. against 65 in. in the United States). However, consideration of seam conditions and mining conditions other than those just mentioned emphasizes differences rather than similarities with United States soft coal. In general, the Ruhr seams now being mined are much more folded and inclined than American seams. Dips of 20' and 30" are common in seams now being worked, and 30 pct of the coal reserves in the district are in seams dipping more than 35". Only on the tops and bottoms of folds do we find rather flat coal seams. In addition to the folding there is extensive displacement by cross faulting plus a certain amount of strike faulting of an overthrust nature, which results locally in doubling or omission of seams. Because of the long history of mining in the Ruhr, nearly all coal lying near the surface has long since been mined out, and we find that the average depth of mining is at present about 2300 ft below the surface. Deep mining, folding, and faulting result in seam conditions requiring a great deal more roof support than one finds in American soft coal mines. In fact only in the anthracite district and the Rocky Mountain and Pacific coal fields do we find somewhat similar conditions. It is easy to say, therefore, that the problem of mechanization of coal cutting and loading in the German mines is quite different from that which we have so effectively met in America with our mobile cutters and loaders, duck bill loaders, and a room and pillar system of mining our drift and slope mines. Partly because of more limited coal reserves, the traditional German mining system is largely the longwall method, which gives an almost complete coal recovery. Backfilling must be extensively practiced to protect the longwall faces, the over and underlying seams and workings, and especially the surface industrialized areas and barge canals. The German engineers have accordingly concentrated their efforts on the design of cutters, loaders, and conveyors suitable to longwall methods rather than room and pillar methods. Undercutters with cutter bars like American models have been in use in the Ruhr since well before World War 11. In 1941 they accounted for 8.5 pct of the production. This percentage, of course, includes coal which was undercut but nevertheless had to be broken down with air hammers or with explosives. The most common of these cutters is the Eickhoff Standard cutter (see fig. 1). This machine does about 95 pct of the undercutting in the Ruhr today, and is available with either compressed air or electrical power and in at least four different sizes. A variation of the cutter is this one with two cutter bars (fig. 2). At the end of 1947 about 200 of these machines and similar cutters were accounting for 13.2 pct of the total production, a production which was, however, only 60 pct of the 1941 production rate, so that the actual cutter tonnage was only up to a small amount over 1941. In 1941 about 3 pct of the production was accounted for by shearing machines making their cut perpendicular to the longwall face. They were similar to those used in the States. These machines are today considered obsolete and now account for only 0.7 pct of the total production. They are located at only a few mines and at present do not seem to have much of a future in the Ruhr. For the future, the Ruhr miner is looking forward to rather extensive mechanization of face work, with two major types of equipment being developed almost simultaneously. On one hand there is the development of cutter loaders for use in relatively hard coal. They represent the further extension of ideas developed after relatively long experience with the Eickhoff cutter. On the other hand there has been since 1942 an intense interest in the Ruhr in the development of face-stripping methods, particularly by the Kohlenhobel (coal plow) and its modification. At the end of 1947 these cutter loaders, Kohlen-hobels and scrapers together were actually accounting for only about 1.4 pct of total production while air hammers still broke 77.1 pct and as much as 1.2 pct was actually broken by hand picks. However,

Jan 1, 1951

By J. D. Clark

ONE'S lifetime does not usually offer the oppor-tunity to observe and be a part of the commercial development of an entirely new material. Petalite has been known for over a century, but at first it was presumed rare. However, it was found to be so abundant that it has become a new and extremely useful industrial tool. Mineralogy Petalite is a lithium-aluminum-silicate mineral. It was from petalite that J. A. Arfwedson first discovered lithium in 1818. The theoretical composition of Li2O • A12O8 • 8SiO2 is equivalent to 78.4 pct silica, 16.7 pct alumina and 4.9 pct lithia. The mineral in its known commercial occurrence is colorless to white and rarely gray, transluscent and rarely transparent. It is brittle, has a vitreous luster, and occurs usually in cleavable masses (fig. 1). It is classified as a di-silicate, but is similar in composition to the metasilicate spodumene, Li2O.-Al2O8-4SiO2 (table I). However, their specific gravities are quite different (3.13 to 3.20 for spodumene, 2.39 to 2.46 for petalite). Occurrence Petalite specimens have been reported in many localities; however, there are only three known countries having occurrences of commercial significance. The classic locality is Sweden's Utö Mines, which, although reportedly still containing considerable petalite, have been closed and are not expected to be operated in the near future. At Varuträsk, in northern Sweden, petalite carrying 4 pct lithium oxide is the main ore. In 1946 there was reported about 1000 tons on hand. However, the iron content was 0.60 pet too high for other than chemical use. Petalite has been reported in western Australia. At the Cottesloe mine, where small quantities have been reported available, it is produced in conjunction with feldspar. Petalite occurs in considerable quantity in the feldspar quarry at Londonderry, and it was estimated1 in 1943 that over 3700 tons might be available. The petalite in South West Africa was first discovered by F. J. Jooste, a lawyer by profession, in 1938. The following year he discovered a much larger deposit, and in 1948 another important discovery was made. These deposits occur near Kari-bib and constitute the only known commercial deposits. Their full extent has not yet been determined, but huge massive blocks of petalite of the purest grade, running into many thousands of tons, can be seen in all these deposits. To date, 60,000 tons of high grade, low iron containing ore has been blocked out in the major bodies. Mining for years to come will be confined to simple quarrying. Selection from accessory minerals has proved

Jan 1, 1951

By T. Binnert Haites

INTRODUCTION NUMEROUS examples of troubled zones, interfering with the normal development of coal seams, have been cited in the literature. From a geological point of view they can be subdivided into structural and sedimentary troubles. Of the latter type, wash-outs are usually the most bothersome. Some years ago, A. A. Thiadens and the author arrived at the conclusion that they represent fossil river-beds. A method of predicting the course of these rivers was developed, which has been successfully applied in the Netherlands coal measures, and more recently by P. Stassen in some of the Belgian coalfields and by the author in the Sydney coalfield. The Sydney coalfield has long .drawn the attention of geologists, and three main periods of systematic geological research may be distinguished. The first period, 1872-1900, is covered by the studies of Ch. Robb and H. Fletcher (32, 10-13) (1). Their detailed sections of the cliffs have lost nothing in value, and are frequently consulted today.

Jan 1, 1951

By John H. Low

Introduction Despite the fact that the .association of magnetite with chrysotile asbestos in the parent producing area of the world, the Thetford Mines - Black Lake area, has been recognized since the ores of that region were first known, magnetic methods were not extensively employed in exploration for asbestos until about the beginning of 1949. Since then, large areas of Ontario, Quebec, and the eastern United States have been prospected both by aeromagnetic and conventional ground magnetic methods. Prior to 1949, a limited amount of magnetic work had been done, notably that of A.H. Miller (1, pp. 184-186), which was carried out in conjunction with the geological survey of the Thetford area by H. C. Cooke (2) in the years of 1930 to 1932. At that time, Miller pointed out that the occurrence of asbestos is associated with very large magnetic 'anomalies' and that, within the Pennington dyke, an area of asbestos- bearing peridotite could be distinguished, by the anomalies, from adjacent areas of non-asbestos ?-bearing peridotite. Since he .also observed large anomalies in what were believed to be ?barren areas, Miller concluded, however, that the magnetometer could hardly be of much or any value in the direct location of asbestos War .and post-war demands on known reserves of asbestos ore, however, stimulated the search for new deposits, and an economical and rapid method of directing speculative drilling was most desirable.

Jan 1, 1951

By C. H. Snyder

Tlie paper deals with details of construction of the Colmol, including improvements in design that will be incorporated in new models. These improvements are results of problems encountered and worked out in experimental operation with the unit. Also included is a descriptive plan of operating where roof and air conditions are of the worst. A summary of production results from the machine is presented. THE various units used in conventional mining are well-built. Generally the universal under -cutter, driven by approximately 50 hp, weighs approximately 25,000 lb, and is a very strong piece of machinery. The drilling machine is not as husky as an undercutter, generally is driven by approximately 15 hp, weighs about 9000 lb, but is a well-constructed, sturdy mechanism. The loader, usually 60 hp, weighs approximately 24,000 lb, and certainly is a strong, rugged unit. The working parts of all three of these sturdy conventional units have been made of tough steel alloys for some time. With the use of three machines having a combined horsepower of approximately 125, with a combined weight of approximately 60,000 lb, and with the possible inherent advantage of single purpose machines performing a single function, the use of considerable explosives has been required to complete the conventional mining cycle. It was therefore our thought, upon conception of the first Colmol,* a machine which was to do the work accomplished by the three conventional units plus explosives, that it must be a rugged mechanism. Now, after building several units, after going through many and varied experiments, and after the expense of some million-odd dollars, we find we have observed and learned nothing that contradicts our original thinking. A continuous miner, if it is to give satisfactory performance, must be a rugged piece of machinery. Ruggedness has been, and is constantly, in the minds of our engineers in designing the Colmol. Improvements where they have been required have been in the direction of more weight, more horse power, better alloys, bigger hydraulic pumps and motors; in short, always, toward more torque, greater strength, more ruggedness. Now not only the finest steel alloys are utilized but more than 100 Timken roller bearings are used. The following is some pertinent data on models being built and to be built: The low unit: Cutting height, 30 to 42 in. By changing the upper gear case the maximum cutting height can be increased to 61 in., giving a variable cutting height of from 30 to 61 in. Width of cut, 9 ft 6 in. Width of body, 75 in. over tracks. Height of body, 271/2 in. Overall length, 23 ft. Driven by three 50-hp motors or a total of 150 hp. Weight, 26 tons. The intermediate unit: Cutting height, 451/2 to 72 in. Width of cut, 9 ft 8 in. Width of body, 77 in. over tracks. Height of body, 43 in. Overall length, 26 ft. Driven by three 70-hp motors or a total of 210 hp. Weight, 35 tons.

Jan 1, 1951

By T. M. Morris

A SEARCH of the literature reveals that no measurements have been made of the forces acting between a small solid particle whose surface is hydrophobic, and an air bubble to which the solid adheres, both immersed in water. Analyses have been made of the forces acting to support a greased solid on the surface of water, and the forces acting to cause a solid, whose surface is hydrophobic, to adhere to an air bubble in water. The latter analysis T. M. MORRIS, Junior Member AIME, is in the Department of Metallurgical Engineering and Mineral Dressing, School of Mines and Metallurgy, Rolla, Mo. New York Meeting, February 1950. TP 2734 B. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received May 16, 1949. This paper is the result of work done for part of a doctor's thesis at the Missouri School of Mines and Metallurgy. is often incomplete, however, because the internal pressure of the bubble has been neglected. It will be demonstrated that the internal gas pressure is not a negligible factor when dealing with bubbles of the size encountered in flotation. A study of the forces acting between an air bubble attached to a large flat surface is informative. It must be borne in mind, however, that this is not the condition present in a flotation cell, where the particle is small compared to the size of the bubble. The bubble is allowed to spread to its maximum contact angle on a large flat surface in the first case, whereas in the second case, the spread of the bubble is limited to the surface of the small particle which is presented to the bubble. Kabanov and Frumkinl studied the forces acting to cause adhesion of bubbles of hydrogen to a large surface of mercury, which served as an electrode in a dilute sulphuric acid solution. The force acting to hold the bubble to the mercury surface was found to be the vertical component of the surface tension between hydrogen and the sulphuric acid solution. The forces tending to cause the bubble to separate from the mercury surface were found to be: (1) the force exerted due to the internal pressure of the bubble acting upon the area of contact between the bubble and the mercury surface, and (2) the buoyant force of the bubble minus the hydrostatic force acting at the base of the bubble. These investigators photographed bubbles that were just on the verge of separating from the mercury surface. From these photographs, they measured the contact angle between the mercury surface and the tangent to the hydrogen-solution interface at the point of contact between bubble and mercury surface. They calculated the volume of the bubble and the internal pressure of the bubble. The equivalence between the upward acting and downward acting forces was remarkable. Wark2 pursued an investigation similar to that of Kabanov and Frumkin, and at the same time. His deductions verified those of Kabanov and Frumkin. He also considered the conditions present in flotation and was aware of the effect of the internal pressure of the bubble. Further, he proposed several conditions under which a small solid particle would adhere to an air bubble in water. In 1922, Edser," an English physicist, made the following statement. "It must be remembered that no particle could float stably, but for the possibility of variation of the contact angle, for if this were a constant, a slight tilt would inevitably cause the particle to sink." Wark criticized this statement, maintaining that the contact angle does not vary. The experimental data to be presented indicates that Edser was correct. Experimental Procedure: Briefly, the experimental procedure was as follows. A bubble of air was generated in distilled water. A rod of known diameter, one end of which was water repellent, was attached to this bubble. The weight of the 'rod was measured. The internal pressure of the bubble was measured with a manometer. The hydrostatic head from the surface of the water to the bottom of the rod was measured. The angle between the horizontal projection of the end of the rod and the tangent to the bubble at the circle of contact be-

Jan 1, 1951

By J. K. Kerver, J. S. Osoba, J. G. Richardson, P. M. Blair, J. A. Hafford

This paper presents the results of laboratory measurements of relative permeabilities to oil and gas on small core samples of reservoir rock by five methods, and describes the influences of such factors as boundary effect, hysteresis, and rate upon these measurements. The five methods used were the "Penn State," the "single core dynamic," the "gas drive," the "stationary liquid," and the "Hassler" techniques. In those methods in which the results are subject to error hecause of the boundary effect, the error may be minimized hy the use of high rates of flow. In order to avoid complexities introduced by hysteresis, it is necessary to approach each saturation unidirectionally. Observed deviations of relative permeabilities with rate can be explained as a manifestation of the boundary effect, and disappear as the boundary effect vanishes. The results indicate that all five methods yield essentially the same relative permeabilities to gas. Of the four methods applicable to the determination of relative permeability to oil, three, the Penn State, single core dynamic, and gas drive, gave relative permeabilities to oil which were in close agreement. The Hassler method gave relative permeabilities to oil which were consistently lower than the results obtained by the other methods. INTRODUCTION The relationship between the effective permeability of a reservoir rock to each of the fluids flowing through it and the corresponding fluid saturation is an important characteristic of the reservoir rock. Knowledge of this characteristic is and gas reservoirs and of the ultimate recovery to be expected extremely important in the prediction of the behavior of oil under various operating conditions. These effective permeabilities are usually expressed as the "relative permeability" to a fluid phase, defined as the ratio of the effective permeability to the permeability of the rock to a single phase at 100 per cent saturation. Relative permeability-saturation relations are not the same for all kinds of reservoir rock, but may vary from formation to formation, and within the different portions of a heterogeneous formation. In studying the performance of a specific reservoir, it is necessary, then, that the relative permeability characteristics of the individual portions of the reservoir be measured. These measurements may be made in the laboratory on small core samples from the reservoir. Various techniques have been proposed for the measurement in the laboratory of relative permeability-saturation relations. In varying degree, difficulties attend the use of all of the methods which have been proposed. It is the purpose of this paper to discuss the factors which influence the measurement of relative permeability, the difficulties encountered in several methods, and to present comparative results obtained by the use of various techniques. FACTORS WHICH INFLUENCE THE MEASUREMENT OF RELATIVE PERMEABILITY It is necessary that the relative permeability data measured in the laboratory yield the same relative permeability-saturation relationships that would govern the flow of fluids through the sample if it were to occupy its original position in the reservoir. Since the core sample upon which the laboratory measurements are made is not surrounded by similar core material as it was in the reservoir, an error in measuring the relative permeabilities may arise from the "boundary effect" which results from a discontinuity in capillary properties of the system at the effluent end of the core. Again, the rates of

Jan 1, 1951

By A. R. Kaufman, P. Gordon, C. H. Schramm

AS a part of the general program on alloys of uranium carried out at the Massachusetts Institute of Technology under contract W-7405-eng-175 for the Manhattan Project during the recent war, it was considered desirable to investigate the boundary binary phase diagrams of the ternary alloy system uranium-tungsten-tantalum. Previous work on these alloys was practically nonexistent. A brief statement to the effect that tantalum and tungsten form a continuous series of solid solutions was found in a general paper on tantalum by W. V. Bolton1 but no information was available on the uranium-tungsten and uranium-tantalum systems. The research to be described in this paper has served to delineate the main features of the uranium-tungsten, uranium-tantalum phase diagrams and to check Bolton's work on the tungsten-tantalum diagram. Experimental Details Metals: The tungsten and tantalum used for preparing the alloys were 99.96 and 99.65 pct pure, respectively. The chief impurities in the metals were about 0.02 pct molybdenum in the tungsten, and 0.2 pct columbium, 0.05 pct tungsten, 0.02 pct barium and 0.01 pct silicon in the tantalum. The uranium used was 99.9 pct pure, with the main contaminants being iron and carbon. (An appreciable amount of magnesium was present in the uranium as received, but this distilled off during melting and so is not reported as an impurity.) The composition of specimens indicated in the subsequent figures and tables of this paper are the results of chemical analyses on the cast alloys except for the tantalum-tungsten alloys. For the latter, chemical analysis was not very reliable as a result of the difficulty of separating tungsten and tantalum chemically. Consequently, the nominal

Jan 1, 1951

By Mann T

The use of dolomite as a refractory began in England about 1870 when the basic Bessemer process for the removal of phosphorus from steel was developed by Thomas and Gilchrist.Knowledge of dolomite as a refractory in this country goes back to the early part of this century, at the time when the Hoskins Brothers took over the Lithgow Iron and Steel Works from W. Sandford. The practice then was toimport burned dolomite in casks from England. It is reported that much of the material was powdered when received, but was still serviceable. The earliest. used sources of local stone were in the Bathurst and Mudgee areas of New South Wales, and these dolomites were first used raw. Later, dolomite was burned in cupolas at Havilah near Mudgee, coke being obtained from the South Coast of New South Wales. This plant supplied burned dolomite to the Lithgow steel plant, later to the Australil1n Iron and Steel plant at Port Kembla, and also to the electric steel furnaces at Newcastle, Sydney and Melbourne until the plant was closed down in 1946.The Broken Hill Proprietary Company first obtained its dolomite from George's Plains near Bathurst (this was, really a magnesium limestone) and later from Mount Knowles, a deposit near Mudgee, which was eventually taken over by the CO:plpany in 1918. In 1936 Australian.Iron and Steel acquired from the Southern Portland Cement Company a deposit at Mount Fairy in the Federal...

Jan 1, 1951