Search Documents

By M. Muskat

Calculations are reported on the differential sensitivity of the updip invasion of oil strata of varving permeability to the driving pressure differential. It is assumed that the water-oil interfaces advance with sharp fronts, or that the microscopic displacement efficiency is independent of rate and capillary pressure effects. It is found that, under such conditions, limitations of withdrawal rates will not greatly inhibit the "fingering" and bypassing tendency through high permeability strata unless the differential fluid head across the original oil column is of the order of or exceeds about 80 per cent of the driving pressure differential. In practice, such restrictions will be feasible only for oil reservoirs and aquifers of high permeability and dip, but may develop automatically under combined gas injection and water drive operations. INTRODUCTION A commonly expressed view regarding the intrusion of edge-waters into oil producing formations is that the geometry of such advance is rate sensitive. Specifically, it has been suggested that high rates of advance, stimulated by rapid withdrawals, will lead to "fingering" and an irregular type of invasion, whereas at low withdrawal rates the water encroachment will be more uniform. Two factors tend to support this view. One is the resultant effect of capillary pressure and gravity gradients in the displacement processes' involved in water intrusion, which are magnified at low rates of flow so as to improve the recovery efficiency. The other is the direct retarding effect of the rising water head as it advances upslope into the producing area. Capillary pressure forces give rise to a rate sensitivity of the oil recovery by water displacement in uniform strata as well as differential effects in non-uniform formations. These are basically independent of the effect of gravity and would also occur in horizontal beds or when the oil and water have the same density. Unfortunately, however, the fundamental equation describing the displacement process under the action of capillary pressures can be solved only by numerical or graphical procedures, and moreover the solutions are sensitive to the character of the capillary pressure and relative permeability curves.* On the other hand, the direct effect of gravity can be given a formal analytical solution if the simplifying assumption is introduced that the water advances with sharp fronts in the individual uniform strata. It depends on the absolute permeabilities of the water invaded zones and hence results in a rate sensitivity of the differential invasion in stratified media. Although a tieatment of this factor alone will not give a complete evaluation of the effect of rate on water intrusion in non-uniform pays, it should provide at least a semiquantitative measure of the sensitivity of "fingering" to withdrawal rate. Such a treatment will be presented in the following sections. GENERAL THEORY The basic element of the theory is the history of water advance updip in a uniform stratum (Fig. 1). In contrast to the assumption of constant flow rate, generally made in the analysis of displacement processes, we shall assume here that

Jan 1, 1951

By John S. Bell, J. M. Shepherd

pressure difference of 280 psi measured initially on opposite sides of the major fault in the Hawkins Field led to pressure determinations in the Woodbine sand throughout the East Texas basin. Considering the large area, there is unusually good correlation between pressure losses and points of major withdrawals, these losses indicating that the basin pressure has been materially reduced by withdrawals, primarily from the East Texas Field and secondarily from the old fault-line fields of Limestone and Navarro counties, with the pressure loss varying inversely with the log of the distance from these two main areas of basin withdrawals to the measurement points. Apparently faults located throughout the basin serve as local blocks to continuous pressure gradients. INTRODUCTION The pressure anomalies found in the Hawkins Field, Wood County, Texas,' shortly after discovery have led to an area-wide investigation of the pressure distribution within the Woodbine sand of the East Texas basin. These pressures were obtained by drill-stem tests made for that sole purpose while drilling wildcat wells to deeper horizons. The Woodbine sand of Gulf Cretaceous Age is or has been productive of oil and gas in 42 different fields, with the 28 oil fields currently active having produced 118,000,000 bbl of oil during 1949. With one exception, producing energy for all Woodbine reservoirs has been from water drive provided predominantly by expansion of the tremendous volume of water contained in the Woodbine sand. This producing mechanism was recognized at an early date and was described mathematically by

Jan 1, 1951

By J. P. Sheeha, W. F. Craig, M. Baeyertz

The loss in toughness caused by phosphorus within commercial ranges was studied in AISI-SAE 1340 steel and in molybdenum modifications of this grade. The replacement of part of the manganese by molybdenum in amounts which maintain the hardenability of the standard 1340 grade was shown to counteract to a marked degree the detrimental effects of phosphorus. THIS paper deals with the effect of phosphorus on the toughness of 1340 steel and with the effect on toughness of replacing part of the manganese by molybdenum while retaining the same hardenability as that of 1340. In previous work1 a progressive decrease in toughness was observed when the phosphorus content of 5140 was raised from 0.020 to 0.036 pct; that is, from a moderate phosphorus level to one higher but yet within the AISI-SAE specification for this grade. The structural condition of the steel was tempered martensite. Toughness was evaluated by the transition temperature determined by V-notch Charpy tests. Replacement of a part of the chromium in 5140 by molybdenum provided a factor of safety against loss of toughness caused by phosphorus, especially where the steel was cooled slowly after tempering. Scope of the Study: In view of the improved tolerance for phosphorus obtained by replacing a part of the chromium in 5140 with molybdenum, it seemed desirable to investigate the possibility of obtaining similar improvement in 1340 by replacing part of the manganese with molybdenum. Heats were made at different phosphorus levels, in a series that began with 1340 and ended with steels containing 0.32 to 0.35 pct Mo with 0.82 and 0.90 pct Mn. The analyses of the heats are given in table I. In order to facilitate later discussion, the 1340 heats have been placed together in the order of increasing phosphorus content, and the molybdenum modifications have been grouped according to phosphorus

Jan 1, 1951

By Thomas S. West

A gravel pack completion is described which, in addition to sand screening, permits the exclusion of water and gas from the oil production. A gravel pack composed of alternate layers of different particle sizes is employed which has horizontal but not overall vertical permeability to drilling mud. A packer is run on the tubing and set in the screen member, around which the gravel layers are placed. The hydrostatic pressure of a mud column prevents the entry of fluid above (or below) the level of the packer. The producing level may be changed by raising or lowering the tubing. Vertical coning is controlled by replacing the mud column with oil and continually injecting oil into the sand section above (or below) the packer. Three well histories with this completion are described in detail. Statistics on the first 100 completions of this general type are given. INTRODUCTION Gravel pack type completions have heretofore been almost exclusively for the purpose of preventing sand production. This paper describes and presents well data on a gravel pack procedure which is primarily a selective completion method. Although complete sand screening is achieved, the exclusion of gas and water is the primary objective. The application of this procedure is therefore not limited to unconsolidated sands. Application to hard sand or limestone reservoirs is equally feasible. GRAVEL PACK PROCEDURE Figs. 1 and 2 illustrate the gravel pack procedure employed. The gravel is placed by means of the frangible disc type dump bailer shown by Fig. 1.' This bailer has its lower end closed by a plate glass or steel rimmed cement disc. This disc breaks when the bailer passes over the liner allowing the gravel to be deposited around the liner. The liner employed is usually 2 3/8 in. to 2 7/8 in. OD and 1.995 in. or 2.07 in. ID (ID of 2-in. tubing or 2-in. line pipe). Two tvDes,. of slotted sections have been employed. One type employs horizontal hacksaw cut or milled slots of about 1/32 in. width opposite the producing section. The other type employs the same type,. of horizontal slot. but slots are placed in groups of six at intervals of about 8 in. A cage composed of half round vertical bars, spaced apart, is then welded to the pipe over the slotted sections. This liner has the bottom end closed, usually by bull plugging. The upper end is closed, while placing the gravel, by a cap which is held in place by means of a shear pin. This cap has a mandrel attached to it which extends downward inside of the liner to within a few inches of its lower end. The top of the liner cap is formed to fit a releasing type wire line core barrel overshot. The liner is lowered to bottom on the wire line by means of this overshot and released. The length of the liner is usually suffi- cient to extend to about 20 ft above the highest level to which gravel is to be placed, the upper end of the liner always being in the casing. The dimensions of the liner and bailer are such with respect to the casing size that the bailer will always pass over the liner. After releasing the liner the bailer is run to bottom. Passage of the empty

Jan 1, 1951

By R. M. Treco

THE thermal expansion of pure beryllium was first investigated by Hidnert and Sweeneyl in 1925 on a single cast specimen stated to be of 98.9 pct purity. A study of the coefficients of expansion by X-ray methods has recently been made by P. Gordon' on powder obtained from the Brush Beryllium Co. assaying 97 wt pct beryllium with about 2 wt pct oxygen as an impurity. The present work pertains to about the highest purity metal obtainable from the Brush Beryllium Co. This metal was in the form of lumps which were remelted and cast in a high-vacuum induction furnace. Expansion data in this paper deal with beryllium extruded into bars of rectangular cross-section 4x1/2 in. and the anisotropic expansivity of a large cast single crystal. Analysis of the cast metal after extrusion indicated a beryllium assay of 99.28 pct. Impurities were 0.170 pct Fe, 0.140 pct Al, 0.014 pct Mg, 0.086 pct Si, 0.020 pct Cu, 0.020 pct Mn, 0.007 pct Ni, 0.007 pct Ca, 0.080 pct C, 0.179 pct 0, (as BeO). Part I—Extruded Metal Thermal expansion measurements were obtained with a fused quartz-tube differential type dilatom-eter3 on specimens cut from the extruded sections in longitudinal and transverse directions. Specimens were machined to a diameter of 0.250 in. and a length of 3.000 in. One sample from each direction was vacuum annealed for 1 hr at 800°C. The dilatometer tube was placed in a vertical tube furnace having a uniform temperature zone which was twice the length of the sample. Average time for a complete thermal cycle to 500°C was 18 hr. Temperatures were observed with two chromel-alumel thermocouples attached to the sample about 1 M in. apart. The accuracy of temperature measure-ment was ± 0.25°C. An argon gas atmosphere sur-rounded the specimen to prevent oxidation of the beryllium. Samples were identified as shown in table I. Results - The original plan included measuring expansion up to 1000°C, but the first two runs on sample No. 5 showed that a permanent contraction occurred from

Jan 1, 1951

By J. Chipman, J. B. Gero, T. B. Winkler

D. C. Hilty—This paper is a useful and timely addition to our store of quantitative data relating to manganese distribution between slag and metal in steel-making processes. For some time, many of us have suspected that the values of Kmn derived by Körber and Oelsen might be too low, and this paper now appears to confirm that suspicion. Application of the new constant to openhearth data should prove interesting. The manganese deoxidation curves of fig. 4 agree fairly well with direct measurements of isothermal solubilities of oxygen in liquid iron containing manganese that have recently been made at the Union Carbide and Carbon Research Labs., Inc. According to the solubility data just mentioned, however, the curves for 1550" and 1600°C lie much closer to each other than the authors have indicated. In other words, the solubility measurements suggest that the logarithm of the oxygen solubility is not a linear function of the reciprocal of the absolute temperature, as the authors have assumed for their calculations. It seems possible that this discrepancy may be due in part to the authors' use of the distribution coefficient, L,,, obtained from Taylor and Chipman's curve for the solubility of oxygen in iron as shown in fig. 2. Taylor and Chipman gave the equation of this curve as —6320 Log % 0 - ---T + 2.734 Their data, however, can be fitted equally well by a curve having the equation: 13.23 x104 1.18x10" Log % O = 36.350 -13.23x10 Moreover, this curve also fits the authors' oxygen distribution data somewhat better than does the linear curve of Taylor and Chipman. Its use in the derivation of Lo for calculation of the deoxidation curves by the authors' eq 15 causes the effect of temperature on the calculated curves of fig. 4 to agree quite well with the temperature effect that has been observed. An experimental determination of the temperature coefficient of the manganese reaction appears to be desirable. J. E. Stukel—Because the authors have done such an excellent job, my comments will be confined to additional information. Very shortly Professor T. L. Joseph and I will publish the results of a study of the reaction between molten manganese and silica. It was found that electrolytic manganese, melted in silica crucibles, reacted with the silica to form a silico-manganese alloy containing 18 pct silicon (1500°C) and a silica saturated MnO-SiO, slag. Therefore, the presence of silicon and its oxides in the Fe-Mn-0 system will affect the equilibrium. Carbon is also an important factor. The higher the carbon content of the iron the less ability manganese has to reduce silica. As a matter of interest, recently a study of the manganese equilibrium in carbon saturated iron and blast furnace slags was completed at Carnegie Institute of Technology. As a comparison to the present study, 2 to 5 hr were required to reach equilibrium and temperature was a much more important factor than slag composition in determining the (Mn)/(MnO) ratio. These results will also be published in the near future. It can be seen, therefore, that the results of this paper cannot be applied directly to openhearth studies without a degree of flexibility. J. Chipman (authors' reply)—With regard to the effect of silicon on the manganese constant, this effect is, of course, known. Much more data is needed in order to establish it accurately, and I hope we can look forward to having some accurate data on that. Mr. Hilty suggests that a three-term expression for the Taylor-Chipman solubility of oxygen in liquid iron might fit a little better than the two-term equation. I think that it would be too great a compliment to the precision of the data to employ a three-term equation, and I would still recommend the simple, two-term expression.

Jan 1, 1951

By H. A. Watson

The introduction and use of synthetic materials in various applications may lead to potential hazards from toxic, gaseous, decomposition products if these materials are subjected to conditions abnormal to their intended use, such as high temperatures or burning from accidental causes. This report covers an investigation of such possible hazards from toxic gases produced by the burning or thermal decomposition of some low-density, expanded, synthetic materials, three of which consisted of polyvinylchloride and one of acrylonitrile. In the production of certain expanded plastic materials, Chemical blowing agents frequently are used to produce a cellular structure. One of these blowing or foaming agents contains azo-bis-isobutyronitrile, which is designated in this report as PN. Information indicates that a product of decomposition of this blowing agent, formed in the blowing operation, is tetra-methyl-succino-nitrile, designated as TSN, Which is significantly toxic. Decomposition of the blowing agent, with release of its azo nitrogen, is represented by the following reaction:

Jan 1, 1951

By B. W. Gandrud

In the summer of 1950, Bureau of Mines engineers visited a number of coal-preparation plants in western Europe and Great Britain to obtain information on European and British coal-cleaning and froth-flotation practices. In view of the growing importance of froth flotation as a process for cleaning fine sizes of coal, it was felt that such data and information would be of value in this country, for, although froth flotation has been adopted for use in a few of our plants, it has not as yet been employed as extensively as in British and European preparation plants. Many of the important coal beds in western Europe, especially in the Ruhr Valley of Germany and in the Dutch coal-mining region of Limburg, Netherlands, are very friable, with the result that the run-of-mine product contains a large proportion of the sizes too fine to be treated successfully by any other method than froth flotation. Furthermore, the relatively high cost of producing coal from these beds has for many years made it economically feasible and desirable to treat the fines by froth flotation, especially in the coking-coal fields.

Jan 1, 1951

By W. A. Young

Bull Lake is one of several saline lakes situated a few miles north of Rawlins, Carbon County, Wyo. (figs. and 2).. The Bureau of Mines conducted preliminary investigations of sodium sulfate deposits in many of the lakes and performed detailed work on Bull Lake. This investigation consisted of drilling 11 vertical holes through salt beds using diamond core bits and Iwan-type auger bits. Bull Lake lies in a shallow, closed depression in loosely consolidated sand. The salt beds, ranging in thickness from 2.5 to 26 feet, occur above a thick bed of shale of upper Cretaceous age. The salts appear to have been deposited in the lake from surface and subsurface drainage. The source of salt is undoubtedly the enclosing sedimentary rock's exposed to the west of the basin. Sodium sulfate in the deposits probably is present as mirabilite or Glauber salt (Na2SO4-10H2O). Chief impurities in the deposits arc mud and sand. Other soluble salts present average approximately 1 percent combined. Cores from the 11 holes were analyzed in the Bureau of Mines laboratories at Salt Lake City. Drilling totaled 512 feet. Results of analyses are given in the appendix.

Jan 1, 1951

By A. E. Nehrenberg

THE mechanism by which austenite forms in steels has received a great deal of attention in the literature in past years.'-'* Our present knowledge concerning this mechanism has been recently summarized quite concisely by Bain and Vilella,1 while a few years ago the literature was carefully reviewed by Roberts and Mehl.² The consensus is that any ferrite-carbide interface is a potential site for the nucleation of austenite during heating above the Acl temperature, and that the new austenite generally grows freely to produce approximately equiaxed grains, whether the carbides are initially present in the lamellar or the spheroidal form. In the case of eutectoid steels, growth of the new grains of austenite continues until contact is established with other grains. Then growth stops and an initial austenite grain size is established which does not change until the heating is continued to some high temperature at which grain coarsening begins. In the case of pearlitic steels which are not of eutectoid composition, the proeutectoid ferrite or carbide may interfere with the growth of the austenite if the temperature is not above that designated the A63 or the Acm, respectively. Although a large amount of work has been done to establish the mechanism of austenite formation in steels, it became clear to the present author while he was studying the transformation characteristics of a new 0.25 C Mn-Si-Ni-Mo hypoeutectoid steel" that the manner in which austenite grows in steels depends upon some factor, or factors, not previously considered. This was indicated by the fact that when this steel in the spheroidized condition was heated above the Ae1 temperature the new austenite which was formed did not envelop the carbides and grow in an equiaxed manner as described by Bain³ or spheroidized steels. Instead, in this steel, the austenite was observed to grow much more readily in certain directions than in others with the result that at temperatures within the Ac1-Ac³ ransformation range the austenite grains were acicular in shape. The excess ferrite was also found to be acicular with the distribution of these phases being such that a lamellar pattern was developed. This unusual directional growth of austenite in this new steel initially in the spheroidized condition is illustrated by fig. 1. A search of the literature revealed that this type of growth was not necessarily peculiar to this steel for similar microstructures had been observed by other investigators.4-8 However, the full significance of these microstructures does not appear to have been appreciated, and no work has been done to determine the conditions responsible for this directional growth of austenite or to arrive at an understanding of it. It was for this purpose that the work described in the present paper was carried out. Material: During the course of this investigation a total of 15 steels was studied. They consisted of hypoeutectoid, eutectoid and hypereutectoid carbon steels, and hypoeutectoid and hypereutectoid alloy steels, all of which were obtained in the annealed condition from commercial warehouse stock. As received, the carbon and alloy hypereutectoid steels had microstructures which consisted of spheroidal carbides in ferrite, whereas the eutectoid steel and the hypoeutectoid steels were pearlitic. The grades of steel represented were 1050, 1080, 10110, 3310, 4140, 4340, 4615, 6145, 8620, 9260, 9442,

Jan 1, 1951

By Joseph Bernhardt

THE Cornwall Ore Mines, Division of the Bethlehem Steel Co., at Cornwall, Lebanon County, consists of two separate magnetite ore bodies, approximately one mile apart. The one ore body was an outcrop in which open-pit mining operations were begun in 1742 and continued without interruption. This mine is also served by a shaft for mining that portion of the ore body not recoverable by open-pit methods. The other property had no outcropping and is entirely an underground operation. This mine, cap-tioned No. 4 mine, is serviced by two shafts 220 ft apart. The No. 4 shaft is for hoisting rock and ore, and the No. 5 shaft is for handling men and ma- terials. The shafts are on a catenary curve, closely following the dip of the ore body. Slope of the shafts at the collar is 36", flattening to 26" at the bottom. The footwall at Cornwall is a traprock which varies structurally from solid to highly fractured. Grizzly stations at the top of each chute raise were reinforced by setting timber sills on concrete. Occasionally it was necessary to concrete the entire chute raise. Concreting was done by using 35-yd electric mixers set up in the breaking subs. Sand, stone, and cement were hoisted up through the chute raises to the breaking subs. Late in 1937 it was decided to eliminate chute raises and breaking subs in future development. Haulage levels are 50 ft apart vertically. When ore is below a 40 " dip, slushing drifts are driven normal to the haulages and on 40-ft centers. In a few areas, ore dips greater than 40" and slushing drifts are then placed parallel to the haulage drifts. Finger raises are opposite each other and on 20-ft centers making 20x20-ft draw areas (fig. 1). For loading

Jan 1, 1951

By T. W. Wlodek

Abstract A simplified method of fatigue testing full-dimension, as-rolled, non-machined, mining drill rods is very desirable to the mining and steel industries in the classification of steels available on the market, through the evaluation of their fatigue limits and endurance strength. In this paper one such simplified method is presented and analysed. The preliminary results show many advantages of this method, such as simplicity and constancy of loading. The type of loading applied more or less simulates the working conditions of the outside fibres of the mining drill rods. Additional advantages of this method are the possibility of testing under dry and wet conditions, its quietness, and its ease of operation. Specially designed adaptors and specially applied techniques of fixing and preparation of samples make possible the breaking of a quarter-octagon hollow drill rod in a free length of uniform section in a rotating beam machine. At first glance this seems to be difficult to achieve. In the first preliminary test three different lots of steel were used. S-N curves under dry conditions were determined. These curves permit of the classification of the drill rods on the basis of the fatigue limit and endurance strength of the outside fibres of the metal, which is dependent to a greater or lesser extent on the effect of surface decarburization, surface imperfections, and special surface treatments. The average slope of the S.N curve in the damaging zone, and the fatigue limit in equal tension-compression rotating bending, were determined for SAE 1080, chromium-molybdenum and nickel-chromium-molybdenum mining drill rods. INTRODUCTION The fatigue limit and the endurance strength of mining drill rod steels are of interest to both the mining and the steel industries. These industries are greatly interested in lowering the cost of mining by reducing the consumption of these steels per ton of ore exploited.

Jan 1, 1951

By R. J. T. Charles

Introduction An apparatus that will measure the surface area of a few of the simple minerals with a high degree of accuracy has been described by J. W. Bell (1). His apparatus consisted essentially of a photometric device that would measure the turbidity of fine particle suspensions. Turbidity, in this case, was considered as a function of surface area. Bell's method of surface area determination seemed to offer possibilities of extension and improvement to the point where it might approach a general method of particle size measurement. Theoretical and Practical Considerations of the Photometric Method In order to illustrate how turbidity may be considered as a function of average particle size, and to indicate the type of results expected from a photometric method of particle size measurement involving turbidity, the following theory may be hypothecated. If a number of particles, considered as spheres of uniform diameter, are placed at random in the path of a beam of light, the following expression, which will give the change in light intensity as a function of the diameter of the particles, the specific gravity of the material, and the weight involved, can be formulated from the Beer-Lambert Law:

Jan 1, 1951

THE developments in construction and operation of the basic open-hearth furnace that have taken place in recent years have placed new emphasis on the vital influence played by regulation and control of the combustion system in both furnace production and furnace life. The several factors influencing flame development, such as regulation of fuel supply, air supply, air preheat, furnace draft, and furnace reversal, must be controlled closely if successful furnace performance is to be accomplished. Rugged instrumentation of distinctive design is required to supply dependable information concerning operating conditions, which is requisite to proper regulation of combustion. This chapter attempts to give a practical discussion of the various features of open-hearth practice and instrumentation related to the efficient heating of the furnace, control of temperature, and protection of the furnace structure from accidental overheating. The appended references will be helpful to readers wanting a more detailed treatment of individual topics. OPEN-HEARTH FUELS The most important open-hearth fuels are listed in Table 4-1 together with their compositions and other data useful for combustion calculations. A detailed discussion of open-hearth fuels is not attempted here, but certain factors peculiar to their application to this type of process are briefly indicated on the following pages. Very often an open-hearth shop is forced by economic factors to use a fuel to which its furnaces are not very well adapted, because the general fuel-allocation scheme for the works as a whole seems to demand it. Often a variable marginal supply of coke-oven gas or tar must be consumed by the open hearth, together with another fuel such as producer gas, natural gas, or oil, to fill out total requirements. Most furnaces employ more than one kind of fuel during their usefu1 life; however, the partial redesign

Jan 1, 1951

By Raymond B. Ladoo, C. A. Stokes

T is unfortunate that the word "economics" has -¦¦ come to mean, in the minds of many people, a sort of half-baked mixture of New Deal philosophy and bookkeeping. It may mean anything from mine cost keeping to the theory of gold as a monetary standard. As applied to the industrial mineral industries as a whole it means to us an integrated study of all of the technical, geographical, market, financial, and other factors which determine whether or not a given enterprise has a sound chance of making a business success. Of course it is impossible to generalize too freely in this large group of industries which go to make up the nonmetallic minerals. This group includes such dissimilar products as crushed stone and ca- pacitor mica, phosphate rock and spinning fiber asbestos, roofing granules and potash salts, borate minerals and monumental granite. Yet in many respects their economic problems are similar and, at the same time, far different from those of the metals and of petroleum and coal. These basic differences are almost never recognized by people outside the industries and are rarely appreciated even by metal mining engineers. But in many instances these economic factors are fully as important as, if not more important than, technologic problems. It has been a long fight to get an intelligent and wide-spread appreciation of sound technology in the nonmetallic mineral industries. The importance of the economic side of the problem has yet to be widely understood and appreciated. The problem was outlined in considerable detail by one of the authors some 18 years ago in a long series of articles* and he has since prepared numerous talks

Jan 1, 1951

Jan 1, 1951

By W. W. Anderson

WEBSTER'S dictionary gives the following definition for "efficiency": "Effective operation as measured by a comparison of actual and possible results." Engineers think of this definition in terms of the ratio of output to input, and since they learn early in their careers that output cannot be greater than input, they usually consider a machine to be 100 pct efficient if it operates perfectly, and to be 0 pct efficient if it performs no function at all. Hence, values of efficiency between 0 and 100 pct reflect how well or how poorly a machine has performed; and any method of calculation for determining efficiency that does not show 0 pct when no function has been performed, and 100 pct when a perfect job has been done, is looked upon with skepticism. The literature on performance of coal cleaning equipment contains many references to efficiency of performance, but there is no unanimous agreement among the authors as to how the efficiency should be determined. Numerous methods of calculation have been proposed from time to time, most of which attempt to fulfill the definition of efficiency by comparing output to input, using float and sink data or some other characteristic, such as dry ash content, as a measure. However, to the best of our knowledge, none of the methods advocated in the past meets the requirements of a practical engineer in judging cleaning plant performance, because the formulas previously advocated do not confine numerical values of efficiency between 0 and 100 pct, and the literature does not contain an explanation of the meaning of the formulas under various conditions of operation. Therefore, the following formula, based on Yancey's concept of misplaced material,' is proposed as a measure of efficiency which will conform with the requirement that the values of efficiency must be confined between 0 and 100 pct: Quantitative Efficiency = 100.0 — (pct wt sink* in cleaned coal + pct wt float* in refuse)t • At gravity of separation effected by cleaning equipment. t Total product basis of the size of material under study. It will be noted from this formula that an actual separation between cleaned coal and refuse must be effected by the cleaning equipment before the formula can be used; also, that improperly distributed material in the products must be determined at the gravity of separation, rather than at some arbitrary test gravity. It will further be noted from this formula that the weight of cleaned coal recovered and the weight of refuse rejected by the equipment have their proper influence, because the sink in the cleaned coal and the float in the refuse are expressed in the equation as a per cent weight of the total products of a definite size discharged from the plant. This formula has one other important characteristic, in that it requires no knowledge of the feed to the cleaning unit. Comparison of data on the products from a cleaning unit with the feed to the unit can lead to many worthwhile conclusions. but not in regard to the efficiency of separation effected by the equipment. The reason for this is that mechanical fracture of many pieces of the feed occurs during the cleaning process; and in some processes crushers are deliberately incorporated in the flow to produce size degradation to free impurities from cleaned coal, thereby altering the washability characteristics of the material while in process. When such size degradation occurs in a cleaning process, it is quite possible that this crushing will result in a reduction in ash content in the finer sizes of cleaned coal when compared with the raw coal feed, even though no true separation has been effected. This is due to the fact that the finer sizes have been "sweetened" by the crushing of cleaned coal from some coarser size. Many formulas advocated in the past show high cleaning efficiencies

Jan 1, 1951

By R. F. Mehl, W. Batz, C. Wells

L. S. Darken—It is indeed gratifying to find that the results of the two different methods here reported are in substantial agreement with each other and with the earlier work1 of two of the authors. Dr. R. P. Smith, of our laboratory, has been conducting some experiments at 1000°C to determine the diffusivity of carbon in austenite by a third method— the steady state method. This work, which will soon be reported, is far enough advanced that we can say it is in substantial agreement with that of the present authors. The only disparity which might be considered significant is in the high-carbon region, where we find that the diffusivity rises a little less steeply than indicated in fig. 8. F. E. Harris—The authors have presented an impressive arrangement of data concerning the diffusion of carbon in austenite. Of particular interest is the compilation, table IV, which is repeated in col. B of table V for direct comparison with values (col. A. table V) from a formulation using a single Q value of 31,000 cal as the activation energy for diffusion. This comparatively simple formulation has been used quite successfully in the practical application of calculating the carbon added (or removed) through the face in carburizing and decarburizing experiments, where the face concentrations are held quite constant for known times and temperatures. Literally hundreds of tests have been so checked where the computed and experimental values have varied by less than 5 pct. For higher temperatures, where proper carburizing data are hard to obtain, the diffusion couple is treated as a decarburization of the high-concentration bar and as a carburization of the low-carbon member. The analysis has been limited to a maximum of 1.40 wt pct carbon. The agreement between cols. A and B in table V may be considered fair, if a liberal viewpoint is taken. The use of a diffusion couple has one serious drawback, in that comparatively small amounts of carbon pass through planes of concentration close to those of the initial high-carbon and low-carbon members, and hence small errors become important. In addition to the sensitivity at these high and low concentrations.

Jan 1, 1951

By John V. Beall

BROMO Seltzer blue has gone to war. The blue of the Bromo Seltzer bottle is a product of cobalt, the Nation's No. 1 strategic metal. When the National Production Authority, on Nov. 21, 1950, ordered a 70 pct cutback in domestic use of cobalt, a stab of pain was felt in the hearts of the glass, porcelain enamel, steel, paint, pottery, and electrical and electronic equipment industries. The reason: A full-scale wartime economy with astronomical requirements for jet engines, high velocity projectiles, armor plate, electronic equipment, and the many products needed to win a war. There is little potential comfort for cobalt users in nonessential manufacturing, and the military will be pinched for optimum supplies of the metal. However, if proper measures are taken immediately and current plans are completed, in two years there will be far more cobalt available than ever before. When normal times return, cobalt supplies should be sufficient to meet peacetime military requirements, and greatly expanded domestic requirements that will result from new technological development for wartime but adaptable to peacetime products. The pres-

Jan 1, 1951

By Orville R. Lyons, A. C. Richardson

THE Coal Division of Battelle Memorial Institute, during the course of an investigation conducted for a coal producer, carried out extensive sampling of the fine-coal section of a preparation plant. The information obtained during the testing period was used to evaluate the overall plant operation and provided the basis for. recommended changes in the plant flowsheet. Included in the information were data for the results obtained when using a Bird centrifuge to dewater the particular coal being treated. At the completion of the investigation, the coal producer gave Battelle permission to publish the operating data for the Bird centrifuge in order to make this information available to the coal industry. The authors wish to take this opportunity to express their appreciation to this company and its officials for their willing cooperation in the matter of publication. Description of Preparation Plant: The preparation plant on which the data were obtained is primarily a jig plant. The coal being washed is a low inherent moisture, friable, Pocahontus-type. The washed coal from the jig is dewatered and sized at 1/4 in. by a Parrish-type dewatering and sizing screen. The minus 1/4-in. coal and the underflow water from the shaker screen flow to a sludge tank where, after the coal settles, the coal is conveyed by a flight conveyor into a pump sump. The pump, a 300-gpm sand pump, delivers a mixture of fine coal and water to a Bird centrifuge which produces a dewatered cake and an effluent. At the time when the investigation was made, the centrifuge effluent was returned to the sludge tank and the cake product was mixed with a coarser size of coal prior to loading into railroad cars. The semiclarified water from the sludge tank overflowed into a pump sump from which it was pumped to the jig. As originally designed, the preparation plant was intended to operate with a closed water system but it was found, soon after operations started, that for various reasons this could not be done. In order to provide for removal of excess water from the system and to aid in maintaining the desired minimum percentage of solids in the circulating water, the plant was operated to provide from the sludge tank a continuous overflow of water and fine solids that was sent to waste. The centrifuge feed represents approximately 35 tons per hour of minus 1/4-in. coal in the form of a pulp averaging 38 pct solids. Sampling Procedure: In order to obtain basic data for determining the relationships existing in the fine-coal section of the preparation plant, samples were obtained for: (1) the centrifuge feed, (2) the centrifuge cake, (3) the centrifuge effluent, and (4) the circulating water. The sampling was arranged to start on a Monday, in order to begin operations with a sludge tank full of fresh water, and was continued long enough to allow sufficient time for fine solids to build up within the water system or for a two-day, four-shift operating period. All samples were taken at half-hour intervals except when plant stoppages occurred. After a stoppage the plant was

Jan 1, 1951