Search Documents

By G. W. Geil, D. H. Woodard, W. D. Jenkins

In a series of papers, the authors and their associates have shown the influence of four important factors on the technical cohesion limit.3-l6 By "technical cohesion limitv is meant the technically determin-able resistance to fracture. The four importarlt factors are the stress system, plastic deformation, temperature, and the strain rate, The influence of any one of these factors may be represented by a curve of cohesion limits, although only one point on the curve may represent actual fracture. As the term "fracture stress" has come into general use with the same significance as technical cohesion limit, the authors are here using the shorter term with the understanding that it does not always refer to actual fracture. The previously mentioned series of papers contains ample evidence that plastic extension increases the fracture stress of any polycrystalline metal, In a recent paper of the series,l5 moreover, it has been shown that the effect of plastic deformation on the fracture stress cannot be attributed to reorientation of internal flaws but is a work-strengthening effect, similar to the effect on the flow stress, $ Plastic deformation of steels, however, may not only cause work hardening, but may result in additional hardness because of strain aging. Some evidence that strain aging affects not only the flow stress but also the fracture stress, has been presented in a recent paper.14 In that paper, a study is made of the influence Of Plastic deformstion at room temperature on the fracture stress of ferritic steels at -188°C. The study is based on the results Of two-stage tests. In the first stage each specimen was extended a predetermined amount at room temperature; in the second stage the specimen was tested to fracture in liquid air. In most Of these tests the specimen remained in the testing machine during the interval of about one hour between the first and second stages, it was kept under a tensile load of about 500 lb and maintained at liquid air temperature. The effects of various amounts of .plastic deformation on the fracture stress were thus determined and curves were obtained to represent the influence of plastic deformation at room temperature on the stress at brittle fracture in liquid air.14 Two specimens Of ingot iron, however, were removed from the testing machine at the end of the first stage and several days elapsed before the specimens were tested to fracture in liquid air, As shown in Fig 8 of that paper," the points representing fracture of these specimens are far above the curve representing the results of two-stage tests without a rest interval between the stages. The evidence thus indicated that the fracture stresses of these two specimens were increased not

Jan 1, 1949

By Orville R. Lyons, A. C. Richardson

During the past few years there has been a growing demand by coal operators for detailed information about the performance characteristics of the various dryers now being manufactured, preferably in such a form that the information could be used to determine the type of dryer best suited to a particular drying problem. A few operators have been desirous of going even further, because they are of the opinion that present-day dryers are not properly designed and that fundamental studies of dryer design should be undertaken. This growing demand for a method of dryer evaluation and the indicated need for fundamental research resulted in the sponsorship by Bituminous Coal Research, Inc. of a project at Battelle Memorial Institute to investigate the thermal drying of coal. In investigating this problem, the most feasible method of attack appeared to be a survey of active operations to determine the present status of the thermal drying of coal. Data were obtained, usually by actual plant tests with the cooperation of the various preparation engineers and their staffs, for 9 screen-type dryers, 8 rotary-type dryers, 3 continuous-pallet-type dryers, 2 flash-type dryers, I tray-type dryer, and I cascade-type dryer. The testing program provided: (I) data for 24 coal-drying operations, (2) information about the inherent characteristics of the coals dried, (3) information about the previous treatment that the coal had received, and (4) information about operating costs. The data obtained through the dryer survey and relationships determined from the data make it evident that all of the types of dryers included in the survey can be operated with the same degree of effectiveness if each type of dryer is used to dry the sizes of coal for which it is best suited. It should be noted that it is usually undesirable and often impossible to dry different sizes of coal in one type of dryer. By use of the data in the report, any prospective dryer user, having determined the surface moisture percentage and screen-size analysis of the coal to be dried, the tons of water to be removed per hour, and the final surface moisture percentage desired, should be able to determine with a fair degree of accuracy: (I) the difficulty of the drying problem, (2) the approximate cost of drying, (3) the required dryer inlet gas temperature and volume and exhaust gas temperature and volume, (4) the type of dryer to use, and (5) the size of dryer required. The method of testing the dryers and determining the difficulty of drying can be used by operators already having dryers to check the performance of their particular dryer and determine whether they are operating effectively. Considerably more information was obtained from the survey of thermal drying than was anticipated when the survey was first considered. However, a great deal of work still remains to be done in the field

Jan 1, 1949

By B. H. Mot

Underground water has been one of the greatest problems in sinking mine shafts, sealing existing shafts, and driving headings under streams. In the preparation of a proposed shaft or existing shafts for elimination of water leakage, advances have been brought about through the use of a controlled grouting method. The modern method to divert water from proposed shaft sites is known to us as pre-grouting, and from existing shafts, as controlled pressure grouting. This method involves the solidification of the surface and rock by the injection of a liquid mixture of

Jan 1, 1949

By M. E. Volin

The Buckeye manganese deposits are in Stanislaus County, Calif., about 33 miles south of Tracy. From 1917 to 1919 the deposits produced 13,370 tons of ore reported to average 46 percent manganese and 14 percent silica. The deposits are confined to two areas of' development, known as the north mine workings and the south mine workings, about 700 feet apart horizontally. Mineralization occurs chiefly as rhodochrosite and psilomelane interbedded in cherts of the Franciscan formation. As a part of the Bureau of Mines program of investigation and development of domestic mineral deposits, a development project was started November 25, 1940, and completed June 27, 1941. The Federal Geological Survey cooperated by mapping the topography and geology and logging the drill cores. The program included road and. trail building, trenching, underground excavation, diamond drilling, and sampling. The following pages mention the location, brief the history, and note the physical .features of' the district. Mine workings are sketched, the deposit is described, and the plan of the project is noted. The work performed by the Bureau of Mines is explained in the concluding pages with a summary of the drill-hole logs.

Jan 1, 1949

By John W. Buch

At a meeting of the Anthracite Investigations Advisory Committee in July 1944 at Washington, D. C., the initial work and objectives of the Anthracite Mechanical Mining Section of the Federal Bureau of Mines were discussed. It was learned that interest existed in an improved performance of mining thin, steeply pitching beds above the gangway by mechanical methods. One company offered the use of one of its mines for experimental work, and this offer was accepted. Following acceptance, an effort was made by Bureau engineers to devise a mechanical method with a performance better than that of a new hand method proposed by company engineers for an actual mining condition. The method proposed by the Bureau was to drive 30-degree slant chutes across a 10-foot bed pitching 85 degrees. These chutes were to be advanced by using a lightweight, compressed air-powered, shearing machine of German origin that had been tried in a flat Pennsylvania anthracite bed in 1934, and which did not then prove successful because of blasting difficulties. An attempt was made to obtain one of these machines from England, where it was known machines of this type had been used. Shortly thereafter John W. Buch was sent to Europe as a member of the Solid Fuels Mission to the European Theater of Operations organized by the Technical Industrial Intelligence Committee of the Joint Chiefs of Staff. Through his efforts the Bureau of Mines obtained two such machines, known as the Eickhoff model DEK, one from England and one from Germany. This report covers the preliminary testing of these machines in order to obtain mechanical operating data for use in determining the power requirements for cutting anthracite with machines of this design.

Jan 1, 1949

By N. P. Peterson

The Castle Dome copper deposit is of the porphyry type and occurs in a body of quartz monzonite intruded into the pre-Cambrian formations and possibly into the lower part of Paleozoic limestones. The hypogene sulphide minerals include pyrite, chalcopyrite, and a little molybdenite, sphalerite, and galena. Pyrite and chalcopyrite are disseminated or occur in small closely spaced veins. The hypogene mineralization shows distinct zoning in the distribution of pyrite and chalcopyrite, so that the mineralized area can be subdivided into pyritc and chalcopyrite zones. Supergene enrichment, though not extensive, played an important part in the formation of the ore body, the chalcopyritc zone being the pro-tore. Several thin, gently dipping, diabase sills occur in the mineralized area, and the copper content of the rock in and near these sills is substantially higher than average. The formation of the ore body was caused by the combined effects of three forces: I. Zoning of the hypogene mineralization, 2. Richer copper metallization associated with the diabase sills, and 3. Supergene enrichment. Introduction The Castle Dome copper deposit is about 5 miles west of Miami, Arizona, and about 3 miles west of the Miami-Inspiration ore body. The Castle Dome open-pit mine is on the south flank of Porphyry Mountain, a prominent landmark of the region. In 1941 the deposit was being explored by the Miami Copper Co., but the exploration program was cut short when the decision was made to develop the property as a war project. The Castle Dome Copper Co., Inc., was organized as a wholly owned subsidiary of the Miami Copper Co., and arrangements were made with Defense Plant Corp. for developing and equipping the mine and for construction of a concentrating plant. Construction and development work was begun in January 1942, and milling operations started June so, 1943. Since that date, the mine has been in continuous operation by the Castle Dome Copper Co, under a lease agreement with Defense Plant Corp. producing copper at an average rate of 4,000,000 lb per month. To January I, 1946 the total production amounted to 121,088,000 lb of copper,4,271 oz of gold, and 211,755 oz of silver. A detailed study of the copper deposit and the surrounding area was undertaken by the U. S. Geological Survey in June 1943. Other members of the Survey participating in the work were C. M. Gilbert, G. L. Quick, and J. P. Albers. The results of this work will be published as a comprehensive report by the Geological Survey. General Geology The Globe quadrangle, which includes the Castle Dome area, was studied by F. L. Ransome1 of the Geological Survey in 1901 and 1902. His maps and descriptions were

Jan 1, 1949

By Gordon H. Chambers

MANGANESE ore is a true jack-of-all trades among industrial minerals, its only possible rival being iron ore. It is used in porcelain enamel, dry batteries, building brick, glazed pottery, floor tile, plastics, welding rods, chemicals, and varnish. You may be reading this through spectacles decolorized with manganese, and the light bulb above you contains some of this element. GEOLOGY Nearly all commercial manganese oxide deposits are of secondary origin; that is, they are concentrated by weathering from other manganese minerals more sparsely distributed in veins. The oxide minerals usually form irregular masses but in some places (Russia) they occur as beds of varying thickness and purity. Some manganese oxide bodies occur in soft gravel or clay formations but in other places the minerals are found in the form of veins and rounded nodules in limestone and other hard rocks. The geologic features of manganese deposits closely resemble those of iron deposits. Classification of the deposits is shown in the following table: I. Classification of manganese deposits based upon form of occurrence A. Stratiform masses 1. Oxides interlayered with sediments or layered volcanic or metamorphic rocks 2. Carbonates or silicates interlayered with sediments or layered volcanic or metamorphic rocks 3. Oxides, as surface bog deposits B. Veins and breccia filling 1. Oxides in larger part 2. Carbonates or silicates partly weathered to oxides C. Irregular masses 1. Oxides 2. Carbonates or silicates largely weathered to oxides D. Aggregates of small oxides in clay or weathered rocks 1. Mainly oxides E. Unclassified deposits II Classification of manganese deposits based upon mode of origin A. Hydrothermal deposits

Jan 1, 1949

By E. G. De Coriolis

The development of huge production facilities and of new or improved processes for manufacturing magnesium from its raw sources has been an outstanding achievement of this war. Furthermore, at least one new method has reached a stage of pilot production that offers promise. Its potentialities seem to indicate that a reduction in cost and simplification or elimination of problems incident to the use of at least one of the present processes are quite within the realm of possibility. Although magnesium of very high purity (99.9 per cent and higher) is obtained, and the rate of recovery reasonable (60 to 70 per cent). the ferrosilicon reduction process is open to a serious objection, which at the time its use was proposed was thought to be sufficient to raise some doubts as to its success, at least on a high production basis. The temperature range at which the reaction is carried out—namely, 2100" to 2150°F.—is very close to the failure temperature of the material of which the retort is made. It is so close that for a time it was assumed it might make commercial use of the process an impossibility. However, at the time under discussion, the demand for magnesium was so great that it was felt by those who had to go ahead and produce this essential metal that the emergency warranted their taking a chance on this process. Subsequent developments have fully justified the soundness of their decision. Fortunately for the war effort, when the plants were put into operation it was discovered that although the retorts did collapse in rather short periods of time, as predicted, they could be blown back into operable shape by application of high-pressure air. This practical method of operation so relieved the situation that the problem disappeared. Nevertheless, if the process had not been successful, or the production of magnesium by the electrolytic process had not been able to keep pace with demands, our war program would have been seriously impaired. Fireless Cooker'' Process For this reason a program was set up and assigned for the development of a new method that had been suggested to the War Production Board in 1941. It is believed justifiable in terming the method "new" for several reasons: (I) while utilizing the same (ferrosilicon) process as the Pidgeon, hence involving similar reactions, the type of retort or furnace is essentially different, (2) the method of operation, reaction temperatures, etc., differ materially, and, most important of all, (3) the problems to be overcome in making the process successful were not and could not have been anticipated by anything previously known about the Pidgcon process. As will be shown later, the briquetting process, the condenser, the furnace lining

Jan 1, 1949

By Eugene H. Dawson

MICA is a mineral that once was a familiar sight as fireproof windows in stove and furnace doors and as lamp chimneys and shades. Since 1878, the beginning of the electrical age, the use of mica for such purposes has gradually declined and its use in electrical equipment and appliances has developed to such an extent that the known sources of supply are scarcely equal to the demand. With the increasing capacity of electric generating units, the size of mica sheets found in nature was inadequate. However, in 1894, a process was developed whereby thin films or splittings cemented with shellac or other binders could be pressed into large sheets. 18 The introduction of radio in the early 1920s created such a heavy demand for the smaller sizes of mica that on March 22, 1938, mica was included among 23 commodities on the list of strategic materials approved by the United States Army and Navy Munitions Board. To be included in this list, the material must be one whereof the domestic supply is not sufficient to meet the demand. COMPOSITION Mica is a complex mineral composed principally of the silicates of potassium, aluminum, and magnesium. Less prevalent species contain, as essential components, lithium, vanadium, and chromium. Iron usually is present either as an essential component or as an impurity. The mica group comprises some nine different species, five of which, muscovite, phlogopite, vermiculite, lepidolite, and biotite, are widely used in industry. Lepidolite and zinnwaldite (lithium micas) and roscoelite (vanadium mica) are sources of lithium and vanadium. Muscovite, "white mica," is potassium mica. Theoretical formulas H2KAl3(SiO4)3. There are two varieties, distinguished as to color, known in industry as ruby and green. In crystals or "books," the colors each range through varying shades of red and green. However, when split into thin films, all micas, except biotite and phlogopite, are colorless and transparent. Muscovite frequently is stained red or black by thin films of iron oxide between the laminae. The staining usually is derived from magnetite, which sometimes is found as unaltered crystals.

Jan 1, 1949

By W. P. Saunders, W. R. Hibbard, G. H. Eichelman

Interest in the various products of the austenite eutectoid transformation in iron-carbon alloys, particularly as produced by the isothermal sub-critical techniques introduced by Davenport and Bain,' has resulted in the application of similar heat treatments to other eutectoid transformations. Studies o f the beta copper-aluminum alloy eutectoid transformation revealed microstructures very similar to those found in iron-carbon alloys. Investigations5t6 of the kappa phase in the copper-silicon alloy system have established the eutectoid type transformation of this phase into terminal alpha and intermediate gamma phases. This transformation has been reported5 as forming a eutectoid type structure in a very sluggish manner by a long time isothermal treatment. The purpose of the present investigation is to study the products of the kappa eutectoid transformation as affected by transformation temperatures by means of microscopic and hardness methods. Preparation of Alloys The copper-silicon alloy equilibrium diagram is shown in Fig 1. The kappa field converges to a minimum silicon solubility at the eutectoid composition and all other completely kappa alloys are hypereutec-toid. Thus, kappa decomposition involves first the proeutectoid precipitation of gamma, followed by the eutectoid transformation of a lower silicon content kappa (5.2 pct) Smith6 has indicated that alloys containing between 5.4 and 5.7 pct silicon could be hot rolled, but that the latter composition was desirable in order to permit a wider kappa temperature range. The alloy was prepared by adding Baker's commercially pure silicon to an ingot of copper-silicon alloy containing 2.34 pct silicon remaining from the investigation of Brick, Martin and Angier.' Following the casting techniques of Krynitsky, Saunders and Stern,s the ingot was melted under a heavy layer of dried charcoal in a clay-graphite crucible in a gas-fired pot furnace. Small lumps of silicon were held under thc melt surface with a graphite rod. After the silicon had dissolved, the alloy was chill-cast and then remelted without a cover, stirred thoroughly, skimmed and poured into a preheated cast iron mold. The cast microstructure is shown in Fig 2. The casting, 10 X 4 X K in., was annealed at 750°C for 21 hr and furnace cooled, About }{& in. was milled from all surfaces. The plate was cut in half longitudinally and the bottom half analyzed by A.S.T.M. and The composition by weight was as follows: copper 94.24 pct, silicon 5.56 pct, iron 0.11 pct.

Jan 1, 1949

By Wilson D. Michell

The Magma copper vein trends east-west, dips 70" south, and cuts through a 6000-ft thickness of limestones, quartzites,. shale, diabase, and schist. The vein is itself a fault with a horizontal offset of 500 ft on the formation contacts in the two walls. There are two principal faults of large displacement and numerous smaller steep and flat faults that complicate the prediction of ore occurrence. A study of the geology, its systematic recording to facitliate ready reference, and graphic methods of interpretation of mineralization have aided the exploration, development, 2nd mining of the ore. In making predictions of the distribution of mineable ore bodies and their shape in critical areas, studies are made of "mineralization contours" and "mineralization trends," which are developed on a longitudinal section of the vein from variations in the concentration of the combined base metal content as shown by assays of available openings in the mine. Introduction This paper describes an example of geological work applied directly to mining and exploration problems in a deep vein deposit, and it is presented as being of interest especially to those engaged in working more or less similar veins. In 1944 to 1945 the writer spent a year as assistant to J. K. Gustafson in a thorough geological examination of the Magma mine. Much of the writer's subsequent independent work described in the present paper had its inception in ideas originated by Gustafson during that examination. Objectives of Geological Work at Magma Mine The objectives of geological work at Magma, as at operating vein mines of a similar nature, can be summarized as follows: 1. Direct assistance to the mining department by means of predictions as to the size, shape, grade, and location of ore bodies; by solution of fault problems and irregularities in the veins; by prepara-?ion of detailed ore-reserve estimates in specific areas; by keeping a complete record of the geology and assay results in the mine; and by guiding development work. In short, geology can aid in the realization of the prime purpose of the mining department, which is that of producing the greatest amount of ore in the most economical and expeditious manner possible. 2. Guidance for exploration, especially diamond drilling, in undeveloped areas of the mine. 3. Contributions to the understanding of the general geology of the deposit and its regional setting, including ore genesis, structure, and mineral relationships. Magma Ore Deposit The east-west trending Magma vein, dipping about 70" south, cuts through a 6000-ft thickness of concordant limestones, quartzites, shale, diabase, and schist, named in descending order. These

Jan 1, 1949

By W. J. Blackstock

Introduction To The great majority of people, the term 'strip coal' has little or no meaning, or if it has any significance it is thought to refer to a poor grade of coal that had to be accepted during the war because no other fuel was available. Few people in the Province of Alberta realize the magnitude of our coal stripping industry, and fewer realize that strip coal has been available to domestic consumers for at least forty years. Among the first in the field of strip coal mining in Alberta were the Tofield Coal Company, Ltd., and Sterling Collieries Company Ltd. It was not until the advent of World War II, with its huge drain on industrial and domestic coal sup? plies produced by the underground mines, that some other source of coal was seriously sought. The tremendous shortage of manpower du ring this period of National emergency made it imperative that any increase in the coal production must be procured on a high tonnage per man-hour basis. It was therefore natural that the highly mechanized strip mine should be eagerly encouraged and subsidized by the Governmental agency - the Emergency Coal Production Board - under the very able direction of Mr. G. A. Vissac.

Jan 1, 1949

By A. H. Redfield

BITUMENS have been defined by Abraham1 as substances of variable color, hardness, and volatility; composed principally of 'saturated hydrocarbons, substantially free from oxygenated bodies, sometimes associated with mineral matter; the nonmineral constituents being fusible and largely soluble in carbon disulphide. The principal bituminous substances other than petroleums known to commerce are: (1) native asphaltites, such as gilsonite, grahamite, and glance pitch, distinguished by their hardness and relatively high fusing point; (2) native asphaltic pyrobitumens, such as wurtzilite, distinguished by their infusibility and comparative insolubility in carbon disulphide; (3) mineral waxes, such as ozokerite, distinguished by their high content of crystallizable paraffins; (4) native asphalts, containing varying amouqts of mineral matter, distinguished by the comparative absence of crystallizable paraffins; and (5) bituminous residues obtained from the distillation of petroleum. GILSONITE Gilsonite, a black native asphaltite 98 to 99.9 pct pure, characterized by a hardness of 2 (Mohs), a specific gravity of 1.01 to 1.10, and melting point of 230° to 400°F (K and S), is mined commercially only in northeastern Utah. It occurs in parallel, almost vertical veins, from a few inches to 18 ft wide and 8 to 30 miles long, that cut across the Tertiary limestone and shale of the broad Uinta Basin. The bitumen is believed to have been distilled by heat from oily material in the underlying Green River shale. At the Rainbow mine of the American Gilsonite CO.,† the gilsonite, formerly extracted in an opencut by a system of slopes and benches, is now mined by shafts and horizontal drifts. Little timbering is required. The mining methods of the Raven Mining Co., Chicago, and of the American Asphalt Association and the Utah Gilsonite Co., both of

Jan 1, 1949

Temperatures in the Open-hearth Furnace. By Robert B. Sosman. (Metals Tech. Aug. 1948, T.P. 2435) Steelmaking Direct Oxidation in the Basic Open Hearth Process. By E. R. Hughes and F. G. Norris. (Metals Tech., June 1948, T.P. 2380) With discussion Operation of Oxygen-enriched Open-hearth Furnaces. By J. S. Marsh. (Metals Tech., Aug. 1948, T. P. 2416) With discussion Role of Thermochemical Factors in Basic Open Hearth Production Rate. By T. E. Brower and B. M. Larsen. (Metals Tech., Oct. 1948, T.P. 2451) Structure, Segregation and Solidihcation of Semikilled Steel Ingots. By M. Tenenbaum. (Metals Tech., Sept. 1947, T.P. 2273) With discussion The Origin of Silicate Inclusions in Basic Electric-arc-furnace Steel of Higher Carbon Contents. By Axel Hultgren. (Metals Tech., Aug. 1948, T.P. 2418) A Method for Determining the Origin of Surface Defects in Rolled Steel Products. By C. L. Meyette and V. L. Elliott. (Metals Terh., June 1948, T.P. 2368) With discussion Gases in Steel The Sampling and Analysis of Steel for Hydrogen. By G. Derge, W. Peifer and J. H. Richards. (Metals Tech., June 1948, T.P. 2362) With discussion Apparatus for the Hot-extraction Analysis for Hydrogen in Steel. By C E. Sims and G. .I. Moore. (Metals Tech., June 1948, T.P. 2369) With discussion A Quantitative Experimental Investigation of the Hydrogen and Nitrogen Contents of Steel during Commercial Melting. By C. E. Sims, G. A. Moore and D. W. Williams. (Metals Tech., Feb. 1948, T.P. 2347) With discussion The Effect of Hydrogen on the Ductility of Cast Steels. By C. E. Sims, G. A. Moore and D. W. Williams. (Metals Tech., Sept. 1948, T.P. 2454) Sulphur in Ironmaking Kinetics of the Transfer of Sulphur across a Slag-metal Interface. By Lo-ching Chang and K. Goldman. (Metals Tech., June 1948, T.P. 2367) With discussion Some Correlations between Variables Affecting Sulphur in Blast Furnace Iron. By T. E. Brower and B. M. Larsen. (Metals Tech., Sept. 1948, T.P. 2465) Tracer Study of Sulphur in the Coke Oven. By S. E. Eaton, R. W. Hyde and 11. S. Old. (Metals Tech., Sept. 1948, T.P. 2453) Transformation of Austenite Anisothermal Formation of Bainite and Proeutectoid Constituents in Steels. By Leonard D. Jaffe. (Metals Tech., Dec. 1947, T.P. 2290) With discussion Austenite Transformation Above and Within the Martensite Range. By R. T. Howard, Jr. and M. Cohen. (Metals Tech., Oct. 1947, T.P. 2283) With discussion

Jan 1, 1949

By H. R. Deeth, C. J. Koenig

About ten years ago nepheline syenite was introduced to the ceramic industry and the material has now found application in the various branches of the industry, namely, as a vitrifying agent in white-wares and as a source of alumina and alkalies in glasses, glazes, and porcelain enamels. Spencel described the early mining and processing developments regarding this material. Since the time of his article many research papers have appeared relating to the usage of nepheline syenite but little has been published relative to subsequent mining and processing methods. A complete indexed review of the literature was issued recently by Ohio State University.2 Since "Lakefield" nepheline syenite from Blue Mountain, Ontario (Fig I); is the only commercial ceramic-grade nepheline syenite now being marketed on this continent, discussion is limited to this operation carried on by American Nepheline Limited, Lakefield, Ont., and its subsidiary in the United States, American Nepheline Cory. at Rochester, N. Y. The Deposit Blue Mountain is a long ridge rising to an elevation of about 350 ft at its highest point above the surrounding country and extending for about six miles in a northeasterly direction across Methuen township, Peterborough County. The rock of the Blue Mountain central alkaline intrusive is fine grained, light colored and of even granitic texture. The solidified mass consists predominately of the minerals albite, nepheline and microcline in order of abundance. The average mineralogical composition for the deposit obtained by a study of 112 samples taken regularly over the whole formation is as follows:3 Volumetric Mineral Per Cent Albite.................... 54 Microcline................ 20 Nepheline................ 22 Muscovite................ 2 Mafics.................... 2 (Biotite, hastingsite, magnetite) Total................... loo The mineral nepheline (or nephelite) belongs to the feldspathoid group but is lower in silica content than are the feldspars. It is a silicate of soda, potash, and alumina (NaKAl2O32SiO2). Its presence with albite (Na2oA12O3 6SiO2) and microcline (K2O A12O3 6SiO2) gives the Blue Mountain deposit an alkali content of 15 pct and an alumina content of approximately 24 pct. While this huge alkaline mass is somewhat variable mineralogically, it has a uniform chemical composition. When the iron, mostly in the form of magnetite, is removed during processing, a remarkably uniform finished product is obtained. Geological surveying has disclosed many million tons of nepheline syenite in the Blue Mountain deposit. Diamond drilling in the area where mining is now being carried out indicates a block of about one million tons.

Jan 1, 1949

By R. R. Rogers

Introduction The subject of cathodic protection is not new. In 1824 Sir Humphry Davy, in publishing the results of his investigations for the British navy, pointed out that copper could be protected from sea-water corrosion by connecting it electrically with zinc or iron. Since that time much work has been clone in this field, particularly in the protection of metals from the action of sea water, neutral brines, and treated and untreated waters. Special mention should be made of the successful protection of underground pipe-lines which formerly were badly corroded by the water in the ground. So far, magnesium alloy and zinc anodes have been the most popular. However, fairly recent work has indicated that aluminium anodes will give good service under certain conditions. The principle of cathodic protection has been applied extensively in coating steel articles with zinc and in cladding aluminium alloy sheet with pure aluminium. A valuable discussion of the fundamentals and applications of cathodic protection recently was presented in the Corrosion Handbook. A useful list of references was included in the article.

Jan 1, 1949

By F. R. Archibald

Introduction It is the purpose of this paper to review the subject of roasting as preparation of refractory gold ores and concentrates for cyanidation, with particular reference to operations at the mill of Beattie Gold Mines (Que.), Ltd., Duparquet, Quebec. Two earlier papers relating to the Beattie roasting operations are cited as background to the ? present discussion, and more general reference is made to other publications relating? to geology and metallurgy at Beattie. The Beattie roasting plant was built in 1937 as an addition to the existing flotation and cyanidation plant to permit complete processing of the ore at the mine property. Previously, the flotation concentrate had been cyanided, yielding 70 per cent of the gold values, followed by re-flotation of a concentrate from the cyanide residue. This re-floated residue was shipped to a smelter for recovery of gold values unavailable from direct cyanidation. The roasting plant itself is of interest through application in its design of multiple-hearth roasters and a Cottrell plant for separate recovery of dust and arsenic. In the laboratory and plant studies that accompanied development of the plant into a dependable and efficient working unit have been found principles and ideas applicable to other roasting 'problems. Before enlarging on these aspects relating particularly to the Beattie problems and plant, brief consideration is given to roasting in general.

Jan 1, 1949

By N. H. Fisher

Geographical Distribution 'he most important known deposits in Australia of what are commonly referred to as the beach-sand minerals are along the most easterly part of the Australian coast, between Southport, 17 miles north of the Queensland-New South Wales border, and Ballina, 50 miles south of the border, and most of the production has come from this area (Fig I). Smaller deposits are known to occur farther to the south at intervals for several hundred miles, and beaches have been worked at Yamba, 96 miles south and Woolgoolga, 150 miles south of the border and at Swansea, 60 miles north of Sydney. Important deposits have been shown to exist on north Stradbroke Island and others have been located farther to the north, as far as Tin Can Bay at the south end of Frazer Island. (Fig 2). Table I gives the list of operators with the location of their deposits and workings, their approximate maximum monthly capacity expressed in tons of heavy mineral produced by their concentrating plants before separation into individual mineral concentrates, their methods of mining and concentrating the minerals, and the products obtained. This table applies as of June 1948, but all the operators are remodeling or improving their plants and plant practices will be modified accordingly. In addition, active boring campaigns have been carried out by Alluvial Gold, Ltd., of Sydney, in the Cudgen-Cudgera area, and by Zinc Corporation Ltd., of Melbourne, on Stradbroke Island, and in other places. Physiography Submergence of the order of 100 to 200 ft at the close of the Pleistocene period left the pre-existing hills as promontories and the valleys as deep inlets. Wave action has built bay-bars and sandspits in a northerly direction from the headlands, and lakes and marshes have formed between these bars and the initial post-submergence coast line. These lakes and swamps have been or are being filled in by river-borne sediments or wind-blown sand. Beasley1 has presented evidence that suggests a recent emergence of the coast line of about 10 ft. The evidence for this belief is the presence of a black sand seam 1/3 mile inland and 17 ft above sea level (Fig 3), and although it is not entirely certain that this seam is of beach formation and owes nothing to windblown concentration, other evidence supports the suggestion of recent emergence. Such emergence would undoubtedly aid the formation of bars and sandspits and the easterly progress of the beach front, leaving a series of parallel dunes (Fig 4). This belt of north-south coastal dunes ranges up to 56 mile in width and as many as 15 lines of dune have been counted (Fig 3). The foredune is generally the highest, upto 25 ft high, and there is in many places a flat platform in front of the dune known as the berm. The dunes behind the foredune are lower and less well defined

Jan 1, 1949

By A. Sutherland Brown, Stuart S. Holfand

"The Northeastern part of the Cariboo district lies in the big bend of the Fraser River between Quesnel and McBride. The area shown on Figure 1 extends from just west of Wells to Isaac Lake, about 30 miles across the regional strike of beds.Topographically the area extends from the moderately well dissected Interior Plateau in the west through a transition zone to the fully dissected Cariboo Mountains in the east.The area is an important source of lode and placer gold. The Cariboo Gold Quartz and Island Mountain lode-gold mines have produced more than 32 million dollars in bullion since 1932. Placer-mining has probably produced an equivalent or greater amount, although only 15 million dollars is officially recorded because accurate statistics. were not kept until fourteen years after the origiiaal gold rush of 1860.The regional structure of the Barkerville district was summarized by Lang in the Jubilee Volume (1948, pp. 141-149). Since then a large amount of detailed and areal mapping by the writers has expanded the information available and made necessary a complete revision of the regional geology. Much of the information summarized in this paper, together with a full discussion of the revisions, may be found in British Columbia Department of Mines Bulletins, Nos. 34 and 38, but other information is as yet un-published.Rocks of the Kaza group are exposed in the core of the Lanezi anti-clinorium between Spectacle and Isaac Lakes. The main part of the group is composed of greenish micaceous greywacke and greenish schist with knots of garnet, biotite, or both, and minor amounts of pebble conglomerate. The upper 1,000 feet is composed of white to brown quartzites and brown phyllites. Altogether, about 6,000 feet of the group is exposed. 1t is of latest Precambrian, i. e. Windermere, age."

Jan 1, 1949

Jan 1, 1949