Search Documents

By Tell Ertl, Ernest E. Burgh

INTRODUCTION THE Bureau of Mines is operating an oil-shale mine 10 miles west of Rifle, Colo., as part of its Synthetic Liquid Fuels program. The purpose of operating this mine is twofold: First, to supply oil shale to an experimental processing plant; and second, to develop practices and select methods for mining oil shale on a commercial scale at the lowest practicable cost. The second purpose-that of finding out how to mine oil shale most cheaply-entails considerable mining research. Since the drilling of oil shale probably will be one of the major items of the mining cost, factors that influence drilling speeds were investigated. One phase of the drilling program was the development of a successful hard-surfaced rock-drill bit1 that can be used for drilling long holes in oil shale without changing bits. During that phase, drilling speeds were measured and drill cuttings were collected for assay and for screen sizing. When the cuttings from the individual tests were compared, a definite relationship was shown to exist between the drilling speed and the coarseness of the drill cuttings. PROCEDURE Measurement of Drilling Speeds All drilling in the tests was done with a Model UMB-D-99W Gardner-Denver wagon drill. Round-lugged drill steel, 1 ¼ in. in diameter was used in 6, 12, and 18 ft lengths with 2 1/8 -in. Timken H-type bits hard-faced with acetylene tube borium. The tests were made in the lower adit of the Bureau of Mines oil-shale mine; the grade of the oil shale drilled ranged from 18.6 to 42.7 gal per ton. During the experiments air pressure varied between 75 and 90 psi while water pressure remained fairly constant at 75 psi. All holes were drilled almost horizontally. Each drill hole was thoroughly cleaned of cuttings after being collared. The advance of the drill along the carriage was measured and recorded as the drilling speed in inches per minute. Method of Collecting Cuttings To facilitate the collection of cuttings, each drill hole was collared in a smooth, vertical portion of the oil-shale breast (Fig 1). A galvanized-steel sheet was fastened to the breast below the area in which the hole was to be drilled. The cuttings washed out of the drill hole by the drilling water were guided by the steel sheet into a wooden box. The cuttings that remained in the drill hole after the drill was withdrawn were scraped out and placed in the same box as the cuttings washed out of the hole. After the cuttings from a 1-min. drilling interval were collected, they were placed in flat metal pans. The fines were allowed to settle and the clear water was decanted. The cuttings then were dried in the sun.

Jan 1, 1947

By C. Ernest Birchenall

AS a basis for further progress in several branches of metallurgy, particularly the study of physical properties of solid solutions and the kinetics of solid-solid reactions, a more complete understanding of the structure of solid solutions and the nature of the metallic bond is- necessary. Any investigation contributing to this understanding should be of primary interest to the metallurgist. Since the metallic bond is characteristic of an assemblage of atoms, it can be studied only where this assemblage exists. One of the most promising approaches to this study of the interactions in metals is through the general problem of binary metallic solutions. Although crystal structures of many solid metallic solutions have been determined and solubility limits for many systems are given in phase diagram studies, progress beyond this is irregular. Electromotive force and vapor pressure determinations have provided thermodynamic activity data for small concentration and temperature ranges in the amalgams and a few other systems.' In two systems, however, copper-zinc and iron-carbon, data are available for the calculation of activities over wide ranges of temperature and concentration. This activity data for the brass system is summarized in the preceding paper.= A detailed study of the solubility and distribution of carbon in iron is given by Smith and Darken.3 Their treatment of interaction energies is applicable only to dilute interstitial solutions. The objectives here will be to derive from activity gats given in the previous paper for the brasses and structural considerations as much new and detailed information as possible about the interactions between copper and zinc in metallic solid solution and the effect of these interactions in determining the short range structure of the equilibrium phases; that is, we shall investigate the energy of interaction between pairs of atoms of the same and different kinds, the deviations of the distribution of nearest neighbors from complete randomness, and show that the conclusions found are consistent with the observed behavior of the brass system. The method of treatment is fairly general for substitutional metallic solid solutions and will be applied to other systems. The determination of vapor pressures of the components of alloy systems is being undertaken in this laboratory to supply more data for this purpose. The information obtained from solid solutions may be extended by careful analogy to liquids as long as the metallic type of bonding is preserved. Since it will be necessary to employ the language of thermodynamics, a brief summary defining the terms used extensively in solution theory is given below. Solution Theory4 An ideal solution is one in which the vapor pressure of the constituent molecules

Jan 1, 1947

By Dawes S

Efficient roof control in colliery operation is a factor that must be maintained for· the maximum reQovery and economic extraction of the mineral. It must be carefully considered in each of the following stages in the life of a mine.1. The primary development and the first working of the mine.2. The maintenance of access roads, intake and return airways.3. The extraction of pillars.FACTORS IN ROOF CONTROLThe main objects of roof control are: The support of the roof in working places, the relief of roof pressure from the workings during pillar extraction, and in some instances the prevention of subsidence of the surface.The support of the roof during development operations and first working, and the subsequent maintenance of these is influenced by:-1. The depth of the seam below the surface.2. The thickness of the seam.3. The dip of the seam.4. The condition of the roof and floor.5. The method of extraction-mechanical or by hand.6. The method of. working-Iongwall or bord and pillar.7. The availability of material.As a general rule, the pressure exerted by the superincumbent strata may be taken as one pound per square inch for each foot of cover, and the crushing strength of coal as 1,500 to 2,000 lb. per square inch; this, of course, varies, but from these figures it may be assumed that seams below 2,000ft. in depth are liable to crush. If any part of the seam is removed, added weight is thrown onto the remaining coal. It is therefpre essential that for effective working this extra weight must be removed or supported as soon as possible.The outstanding principle in the support of mining excavations is to ensure that the supports are set as soon as possible after the natural support has been removed.Where a system of bord and pillar is applied, the early setting of supports reduces the extent to which the roof bends, thereby reducing the liability to ·tension fractures at the centre of the road.

Jan 1, 1947

By William S. Hannan, H. Rush Spedden

FLOTATION may be defined as a process whereby mineral particles are concentrated by selective adhesion to air-liquid interfaces. The process involves attachment of desired mineral particles to air bubbles, and removal of the mineralized air bubbles from the surface of the pulp as a mineral concentrate. PROBLEM Although great strides have been made in understanding the principles of flotation, one part of the process which has not been adequately explained is the mechanism by which selected mineral particles become attached to air bubbles. A glance at the froth of an operating flotation cell demonstrates adequately that use of proper reagents and conditions will result in such attachments; but how such attachment takes place is not definitely known. A better knowledge of this factor might lead to improved flotation practice either through altered machine design or the application of scientific innovations. Direct observation of the behavior of mineral particles and bubbles in an operating cell does not appear promising because of the complexity of the system. For this reason, conclusions concerning the problem must be deduced from theoretical considerations or from observation of simplified systems designed to reproduce conditions thought to exist in an operating cell. PRESENT THEORIES Two mechanisms have been recognized as fundamental in particle-bubble attachment: gas precipitation and direct encounter. It is a simple matter to demonstrate in the laboratory that attachment can be brought about by either mechanism. As to the relative importance of the two in a particular flotation system, however, there is a divergence of views. Taggart1 states, Under exceptional circumstances sufficient force and time to effect attachment may conjoin in an ore pulp undergoing agitation, and a preformed bubble adhere to a collector-coated mineral particle, but the occurrence is rare. . . . Pulp-body froth flotation effects selection in the body of a conditioned pulp by causing gas bubbles to precipitate from solution in the liquid phase preferentially at the surfaces of collector-coated particles, and to cling to these particles. Gaudin2 states that, within the pulp body of an agitation machine, attachment of mineral particles to air bubbles occurs as a consequence of contact between the two. This theory has been supported by theoretical reasoning and much circumstantial evidence. Perhaps the most interesting bit of evidence in favor of this theory is the difficulty in the flotation of fines. If attach-

Jan 1, 1947

By Francis B. Foley

THE casting of steel in large molds brings into play all of the undesirable effects that result inevitably from slow cooling. The origin of the molten metal, whether basic or acid open hearth or electric furnace, has little if anything to do with the phenomena involved. If the quantity of molten metal to be cast in a single mold is large enough, there is very little one can do about it-the metal will cool so slowly that 'nothing one can do, other than to provide as good feeding as practicable from an adequate reservoir of metal in the sink head, will be of any avail. Recently we have had occasion to cast a 108-in. octagon ingot weighing 545,700 lb, necessitating the combining of metal from three 100-ton open-hearth heats. This is one of the largest ingots ever made. The body of the ingot weighed 448,800 lb, which includes a bottom pool of about 7500 lb of metal, and the sink-head weight was 96,900 lb, or about 18 pct of the total weight.

Jan 1, 1947

By Warren E. Wilson

The transportation of solids in pipe lines is a matter of deep concern in many fields of engineering. Much experimental and theoretical work has been done in an effort to devise means of designing pipe lines that will satisfactorily transport given solid loads, but there remain many unanswered questions in this field. The present discussion will be confined to a rather narrow portion of this field and will endeavor to point out certain factors that may well be considered when comparing the relative economy of various installations. The data have been presented previously but a new interpretation was prompted by a suggestion in a paper by Professor O'Brien,' of the University of California, that the friction work per pound of dry material should be considered in determining the relative efficiency of various installations. This method of considering relative economy in various pipe lines leads to some rather unexpected conclusions, especially with reference to the economy of large pipe sizes. A previous suggestion by the writer concerning the economy of a rather peculiar type of installation is strengthened. It is not believed that the considerations set forth herein apply directly in the case of dredge lines, where economy is largely a matter of a high rate of pumping in order to reduce the unit overhead charge. However, it is believed that some value may be gained from these considerations in cases involving the disposal of a fixed amount of solids per unit time with a minimum expenditure of energy and at a low cost for replacement of worn pipes. Such situations are not uncommon in the disposal of mill tailings and the disposal of solids deposited from irrigation waters. It was found that data leading to general conclusions for various pipe sizes were not available but certain definite trends are indicated and methods of analyzing available data are presented in the hope that they may be of assistance in preparing engineering estimates on designs of pipe lines of the type described above. Energy Requirements Carrying out the idea contained in Professor O'Brien's paper concerning the method of computing energy required to transport solids, the following analysis leads to some rather interesting conclusions. Let us represent: Solids load in terms of mass per unit time by w Ratio of mass of suspended solids to total mass of mixture flowing by p Volume rate of flow of mixture by Q Length of pipe by L Slope of energy grade line by s Mass per unit volume of solids by m8. Mass per unit volume of liquid by mi Mass per unit volume of mixture by 11 We then have as an expression for the solids load: w = pqmm The work done per unit mass, p, on the mixture to move it along the pipe the

Jan 1, 1947

By J. C. Williams

The operations described in this paper are those of the flotation plant of the Valley Forge Cement Co. at Conshohocken, Pa., and concern the use of a particular cationic reagent—namely, DP-243. The role of this reagent in this plant may be better understood by first considering the purpose of beneficiating cement rock in general and the specific problems at the Valley Forge plant. The ultimate purpose of beneficiating cement rock is to obtain a kiln feed of the desired chemical composition in a form suitable for the most efficient kiln operation. The chemical composition is governed by the type of cement to be made. Before government restrictions (the purpose of which is to simplify operations during wartime) limited the types of portland cement a manufacturer is permitted to produce, five principal types of cement were generally recognized by the industry. They are based upon chemical and physical specifications proposed by the American Society for Testing Materials, federal and other governmental agencies, state highway departments, water boards and other users of large quantities of cement. The physical as well as chemical specifications for any particular type of cement necessitate proper proportioning of the major components—that is, the silica, alumina, iron and lime—and it is necessary to establish and maintain definite limits for each in the raw mix. The manufacturer must then prepare a kiln feed of a composition that will yield a final product that will fulfill the desired specification. This step is further complicated for kilns using coal as fuel, by the amount and analysis of the ash introduced. The amount and nature of the dust lost during burning will also affect the composition of the kiln feed. The problem of preparing a kiln feed of the desired chemical composition is not a simple one, and it is the final product that governs the methods used to obtain such a feed. For example, in starting with a material deficient in lime for the mix sought, it may not be sufficient to raise it to the required lime content. The other constituents must also be present in the proper proportions. In some cases, it may be necessary to raise the lime content to a point greatly exceeding that of the final mix, then, by addition of one or more other materials lower in lime, obtain the mix. The rock used at the Valley Forge plant is a metamorphosed argillaceous limestone of the Jacksonburg formation, the same formation as that of the Lehigh Valley cement rock (which occurs approximately 50 miles north), and its oxide composition is similar to that of the latter. The only practical differences between the two are that, as a result of metamorphosis, crystallization of the Valley Forge rock is considerably coarser and it contains less carbon than the Lehigh Valley rock as well as slightly more magnesia in the form of magnesian mica. The calcium carbonate content of the various strata in the Valley Forge quarry ranges from about 65 per cent to over 85 per cent, the average for the entire quarry being somewhat under the requirement for manufacture of cement, which usually is from 75 to 76 per

Jan 1, 1947

By Charles Meyer, Reno H. Sales

AT Butte, successive zones of sericitized and argillized quartz monzonite occur around every ore-bearing fracture regardless of its size, attitude, or relative age. The two types of alteration always occupy the same relative positions; sericite adjacent to the ore-bearing vein, clay minerals always between the sericitized rock and fresh quartz monzonite, except where overlap of alteration effects between adjacent fissures has eliminated the lower grade mineralogical products, as is the case in much of Butte's Central zone of pervasive sericitization. As long as active circulation continued in the channel, each zone migrated away from the fissure, that is, it grew at its outer edge and simultaneously receded at its veinward edge because of encroachment by the next innermost zone. The different mineralogical and chemical responses within the wall rocks to the attack by the ore fluid are dependent not on a drastic about-face change of composition of the fluid in the channel relative to its ability to alter the quartz monzonite but on continuously varying conditions of physico-chemical environment within the wall rock outwardly from the vein.

Jan 1, 1947

By H. R. Banks

Pondering the action of a ball mill employed to carry on comminution from the product of fine crushing to the point where flotation, cyanidation or other concentrating methods are applicable, one wonders where this machine had its origin. When Henry Wadsworth Longfellow reiterated the observation of that older poet Von Logau, and wrote "Tho' the mills of God grind slowly, yet they grind exceeding small," he probably visualized the type of mill that was employed in medieval times for the production of flour, and can therefore not be considered as having gained admittance to the fraternity of millmen, on behalf of either poet. He does, however, make it quite clear that the efficiency of even these Mills of Destiny was low, and to that extent voices a characteristic of fine-grinding equipment that has been the bugbear of all metallurgical engineers. Principle of Ball Mill The principle of the ball mill probably is traceable to the action along the coast line of oceans or lakes, or in the mountain streams. Wave action on rocks and pebbles, close to the shore line, gives the potential energy to the grinding media, which, in their rolling and tossing, break down the sands, and the resultant "pulp" carried out from the shore is classified and settles out in sizes ranging downward to extremely he mesh. Surely, these are the real mills of God. If we allow our minds to dwell on the total tonnage that has been handled in this way, adding to the sands and clays at present in existence those enormous tonnages of metamorphosed sedimentaries we sense the vast quantity of rock that has been so reduced. Is it not likely, therefore, that the answer to the beginnings of pebble milling, and eventually ball milling, came through the perception of this natural mill by one of our engineering forebears? Methods of Grinding The relatively low return of mechanical input to a ball mill, in terms of useful work accomplished, has always intrigued me immensely. The potential energy absorbed by a ball raised to a high point in its path is apparently released with a very small return in useful work. Is the ball mill the most desirable means of he grinding, or is there some other method through which we can recover a reasonable amount of the energy input in terms of useful work? Some years ago, on his retirement, H. W. Hardinge was questioned as to his thoughts on the trend of fine-grinding equipment. As I recall, his prophecy at that time was that the most likely field for improvement in grinding media would be toward a charge of flat disks with some mechanical scheme to cause them to slide over each other. Undoubtedly, Mr. Hardinge went through the usual experience of the muller and bucking board, the customary introduction of the budding millman to his calling. I have often wondered, but have never got beyond the wondering stage, as to the

Jan 1, 1947

By Albert J. Phillip

Jan 1, 1947

By B. M. Larsen

IN spite of the great amount of operating experience and of studies directed toward elucidation of the interrelation of the several processes going on in the blast furnace, the present picture of its operation is based largely on indirect evidence and on speculation. The reason for this unsatisfactory situation is the extreme difficulty of making direct observations and significant measurements while the furnace is operating, and of translating laboratory experience to the conditions obtaining in the smelting process. Yet there are questions that can be investigated with some promise of a definitive answer; and it is the purpose of the present paper to set forth some of these questions, as a basis for discussion, which may, it is hoped, lead to active work on some of them. In order to provide a starting point for this discussion, some views held tentatively by the writer are outlined, along with a certain amount of evidence gathered from operating records and interpreted on the basis of the ideas expressed. These opinions may prove not to be pertinent, and may well not be in accord with the opinions of others; they have been included to encourage others to do likewise and on purpose to provoke informal discussion. In this way it should be possible to transcend the limitations of formal papers; to bring forth suggestions of new hypotheses or new methods of investigation; and to promote better understanding between investigators and operators in this difficult field. The statements made express the present views of one physical chemist who is not too familiar with all the difficulties of maintaining these enormous reaction vessels in reasonably smooth and economical operation; who, however, is persuaded that some of these difficulties would be less formidable if surer knowledge of the several interrelated and concurrent processes were available and made use of. For these difficulties arise largely, it is believed, from variation in conditions which the operator must meet as best be can, and should lessen as these conditions can be brought under control so that they are either made substantially constant or the variations are neutralized by compensating methods. A. VARIATION IN BURDEN AND IN MIXING OF CHARGE To the scientific investigator, who aims to control the conditions of experiment and to limit the number of variable factors, the most perplexing aspect of the blast-furnace process is that nothing seems to remain constant for long. Variations of burden seem to be unnecessarily frequent; and, even if the charge were constant from hour to hour, its constituents usually are not mixed as intimately as they might well be. It is understandable that separate layers of coke and of ore, also separate layers according to size, promote permeability and the

Jan 1, 1947

By J. A. Bowers

THIS investigation of the effect of bottom shape and life on slag volume was carried out in two Lectromelt top-charge furnaces whose rated capacity is 1000 lb per hour. Unfortunately, just as the work [ ] was started, our steel tonnage was reduced approximately one half, therefore we did not accumulate enough data from which to draw any definite conclusions. Furthermore, the life of the linings in these furnaces was greatly decreased by intermittent operation, which was a further handicap in making a study of this kind. The weight of the heats from which the data were taken varied 1200 lb but all the information was corrected to the standard weight charge for these furnaces of 4500 lb. Almost all the heats were plain carbon; a few contained a small percentage of added copper.

Jan 1, 1947

By Harold M. Smith

Among the more important raw materials now utilized for the commercial production of synthetic organic chemicals is natural 'gas. Natural gas has been used as a fuel and source of energy almost from its discovery, but its potentialities as a chemical raw material were not realized until recently. Research in the use of natural gas for Chemical synthesis received great impetus from the discovery by Brooks and Humphrey4/ in 1918 of alcohols in the diluted ?acid oil? obtained by sulfuric acid treatment of cracked petroleum distillates. Experimental data soon showed that hydrocarbons from natural gas could be converted to these same products. Laboratory methods for chlorination of natural-gas hydrocarbons, particularly of methane for the production of methyl chloride, methylene chloride, carbon tetrachloride, and chleroform were known before that time but were not developed commercially. Methods for obtaining alcohol by oxidation of hydrocarbons derived from natural gas also were known before 1918 but had not received commercial consideration. Since 1918, and particularly during the past 15 years, the work of chemists and chemical manufacturers throughout the world has resulted in an accumulation of data regarding the reactivity of natural-gas hydrocarbons, and related hydrocarbons found in refinery gases or made synthetically. These data have been used to develop methods for converting hydrocarbons into chemical products and thus form the basis for a large and growing industry.

Jan 1, 1947

By A. M. Gavdin, F. W. Bowdish

Mineral dressing is an industrial art concerned with the treatment and separation of solids suspended in fluids. Knowledge and evaluation of the area of solid-fluid interface is important in all cases except those involving only large pieces of solid. In fact, many problems relating to comminution, to flotation, to thickening and classification, could be dealt with more rationally if the interfacial area were known. A number of methods have been proposed for the measurement of the surface of certain finely divided solids. Among them are methods using rate of dissolution of the solid,? its magnetic remanence,³ the turbidity of its suspension," and the character of the size distribution of the material.9 The first two are limited to one mineralogical species per sample; the third has certain optical limitations, especially for mineral mixtures, and the fourth is based on an extrapolation of uncertain validity. The need of a better and more general method of surface determination has long been felt, therefore. The method of P. H. Emmett,4 based upon the low-temperature adsorption of vapors, appears to fulfill this need. This method consists in determining the amount of nitrogen that is adsorbed by a given sample of solid at the temperature of boiling nitrogen. The more surface there is on the solid—both internal and external—the more nitrogen is abstracted. In actual operation, the method is somewhat less simple than has been stated so far, in that the nitrogen is adsorbed in an incomplete layer, the completeness and thickness of the layer being related to the pressure of the nitrogen in contact with the sample.2 This circumstance makes it necessary to determine the nitrogen adsorption for three or more values of the nitrogen pressure. Apparatus In the Richards Mineral Dressing Laboratories an Emmett apparatus has been built and tested (Figs. I and 2). A mechanical vacuum pump B and a mercury diffusion pump A work in series to give a high vacuum. The sample, placed in bulb D, can be evacuated by this pump train by suitable operation of the stopcocks in the glass tubing that connects the various parts of the apparatus. C is a McLeod gauge, used to ascertain the order of magnitude of the vacuum obtained, and not for accurate pressure measurements. Pressure measurements are made in the mercury manometer F and gas-volume measurements in the gas burette E. Gases are stored in flasks L (nitrogen) and K (helium), arranged so that definite quantities of these gases can be introduced into

Jan 1, 1947

By R. J. Bridges

Mining operations on the Witwatersrand are conducted for the most part in rocks of highly quartzitic character. They comprise the following types: Conglomerates, grits, and quartzites, to which on the Far East Rand must be added fine-grained quartzitic shales and shales. In addition, vein quartz occurring as small veins, veinlets and fissure fillings, and igneous rocks forming dykes, must be mentioned, although they constitute only a small percentage of the rock broken. The following is an account of the character and mineralogical composition of the various types.

Jan 1, 1947

Jan 1, 1947

By S. C. Oliphant, R. Floyd Farris

Presented in this paper is a summary of the results of experiments conducted in both the laboratory and the field during the past three years in connection with casing-perfora. tion problems. Included are studies of gun features that influence bullet performance and penetration, and studies of the effect of perforator bullets on casing and the neat cement in the annulus. Discussion and data are also presented relative to the accuracy of depth measurements in deep wells. Introduction It is a common practice in the oil industry to effect the completion of oil wells by setting and cementing casing through the producing horizons and perforating the section of casing opposite the desired interval by means of a gun lowered into the well on a cable or on the tubing. This practice has been followed for some time, and this method of completion has been given considerable study by the companies that render perforating service as well as by the oil companies that utilize their services. Through continued research on this subject, it has been possible to develop guns, bullets, and powder that will permit controlled firing at great depths, and penetration of as many as two strings of casing. It is the object of this paper to present the results of studies made of gun perforating in both the field and the laboratory. These studies were made to determine the factors that affect penetration of the bullet, burring of the casing, accuracy of depth measurements, and other items. It is hoped that by presenting the results of these investigations a better understanding may be obtained of certain of the factors involved in gun perforating and further investigation of the subject will be prompted. Subsurface Tests A well approximately 9000 ft deep, which was being prepared for abandonment, was selected for subsurface tests of gun-perforating experiments, In preparing the well for the experiment, 51/2-in. casing in the hole was pulled and racked in the derrick. A test section of pipe, which consisted of 65 ft of 5-in. 18-lb J-55 casing centered inside 7-in. 28-lb N-80 casing, was placed in the derrick corner and the annulus between the two pipes was cemented from the bottom up with 161/2 lb per gal neat cement, which was mixed and displaced with a cementing truck in the usual manner. After the cement had been allowed to harden for about a week, the test section was lowered into the hole on the 51/2-in. casing to a depth of 6600 ft by casing measurements. The hole was filled with drilling fluid weighing 10 lb per gallon. A perforating company was called to perforate the pipe, but was not advised that an experiment was being conducted. The company was asked to check the total depth (to cross pins in the bottom of the test section), then to raise the gun a given distance and fire a given number of shots with 1/2-in. bullets, pick up another distance and fire a given number of 3/8-in

Jan 1, 1947

By H. L. James

THIS paper presents the results and analysis of field trials of various magnetic instruments over anomalies ranging from 20 to 5000 gammas of vertical intensity. The following instruments were used: Askania vertical magnetometer, Wolfson vertical magnetometer (model M-I), Hotchkiss Superdips (used both parallel to and normal to the magnetic meridian, with several settings of the "sigma" angle), Lake Superior dip needle, and the dipping circle for measurements of inclination. The change in inclination over the measured anomalies ranged up to 4°; this caused pronounced changes in sensitivity of the Hotchkiss Superdip oriented parallel to the magnetic meridian. The variable sensitivity not only gives apparent displacement of crests of anomalies, particularly at high sensitivities, but also makes the data difficult or impossible to use in preparation of iso-anomaly maps. This weakness in field performance of the Superdip is shown to be eliminated by orienting the instrument normal to the magnetic meridian and measuring vertical intensity only, which in the latitude of upper Michigan is equal to 97 pct of the total intensity. The dip needle is seen to be relatively ineffectual for location of anomalies of less than 400 gammas.

Jan 1, 1947

By E. E. Wark, I. W. Wark, J. Rogers. K. L. Sutherland

Soaps have hem used as collectors for many years, but only in the last eight years have other long-chain paraffin salts been used. It may be anticipated that these newer collectors will be used mainly with nonsulphide minerals, for which the xan-thates and similar compounds are of little value. On the other hand, the xanthates are both cheap and effective for sulphide ores and seem likely to retain their present cminence in this field. During 1938 and 1939 two of us (E. E. W. and I. W. W.) commenced a comprehensive investigation of the principles underlying the use of paraffin chain salts as flotation reagents. This research was sponsored jointly by the University of Melbourne and a group of Australian mining companies. † A broad, semiquantitative survey was then made of the field covered in the present paper. This was followed in 1940 by further work by one of us (K. L. S.). In 1941 the investigation was taken over by the Division of Industrial Chemistry of the Commonwealth Council for Scientific and Industrial Research, Australia. Discovery of some principles upon which are based the flotation of minerals by paraffin chain salts was followed by their application in the development of processes for the recovery of certain strategic minerals from their ores. Promising results in the flotation of cassiterite from various ores will be described in a subsequent paper. The Paraffin Chain Salts 'he basic requirements for a "collector " in flotation are that it should form a film over the surface of the mineral to be floated, and that this film should be orientated so that hydrocarbon (nonpolar) groups form the effective surface. When modified in this way, the mineral surface possesses some degree of air avidity. All investigators would agree with Taggart, Taylor and Ince23 that such a film can be produced only if the collector compound contains an active (polar) group to attract it to the mineral surface as well as the nonpolar group. One section of this large class of polar-nonpolar compounds is the paraffin chain salts: CH3(CH2)nX where .X signifies a polar group that ionizes in aqueous solution. Though the compound can ionize, it may be a weak or a strong electrolyte, and the hydrocarbon chain may be in the cation or the anion (Table I). Many compounds of similar constitution are available, but the usual polar groups are: -Co2Na, -So3Na, -So4Na, — PO4Na2, or an aminonitrogen group, the

Jan 1, 1947

By R. F. Stilwell

There are three things that all coal consumers look for when they burn coal: (1) suitability for their particular requirements and burning equipment, (2) uniformity of shipments, and (3) quality as expressed by heating value and other chemical and physical tests. Suitability, or proper application, is determined generally from previous buying experience. It is a function of (1) the reliability and integrity of the shipper and distributor, (2) of a certain coal field or seam and of (3) uniformity and quality. Quality is limited by the location and geology of the seam and mine, the mining and preparation methods and equipment and the knowledge and ability of the personnel. Uniformity of shipments is in many ways the most important factor in coal selection. Lack of uniformity in chemical quality, size consist and treatment cause most of the customer complaints that arise from faults of the coal shipper. Lack of uniformity destroys suitability and quality standards, causing a large customer turnover, and greatly increases sales expense and reduces the net return to the operator. Oil and gas fuels are more uniform in quality than solid fuels, and there will be more gas and oil competition for coal markets after this war than before, because the size of their market is a direct function of the dimensions of their pipe lines, which have been greatly increased during the war. Present mechanical coal-cleaning equipment based upon gravity concentration has gone a long way toward giving us a coal of uniform ash content. The chart in Fig. I, by Hebley,1 shows the greater uniformity of the ash content of washed coal as compared with that of raw coal. Wide variation in the nature and amount of ash in the coal feed to the washer leads to a coal of non-uniform ash content. Mechanica1 cleaning equipment does not understand such terms as ash-softening temperature, coking properties, size consist and sulphur content. Unless the feed to the washer is uniform, the washed coal probably will not be uniform. Table I shows the ash, sulphur and ash-softening temperature of two mines in the Pittsburgh bed, both raw and washed, loaded over the same tipple; also No. 3 and No. 4 Pocahontas seams, both raw and washed, loaded from the same preparation plant. It is obvious that they must be blended or loaded separately if a uniform product is to be obtained. Why Is Blending Necessary? It was natural for the operators of captive mines producing by-product coals to recognize the necessity for blending raw coals of different quality and coking characteristics. They have had many years of experience with blending high, low and medium volatile coals at their oven plants. They have found that careful blending gives a coke of more uniform quality and better structure. Coals that could not be

Jan 1, 1947