Search Documents

By E. R. Hughes

Introduction Situated 182 miles east of Vancouver, on the Kettle Valley branch of the Canadian Pacific railway, the Princeton coal field is readily accessible to the Coast markets. The area covers approximately forty square miles and present indications are that the deposits should contain at least 300,000,000 tons of coal. Comparatively little development has yet taken place in this coal field. Since the commencement of recorded output, the collieries operating in this area have produced 1,640,518 tons of coal. The coal field proper includes only the Tertiary deposits adjacent to the town of Princeton and does not include the Coalmont or Nicola deposits. Production has never been on a large scale. The largest annual output from any property was 81, 780 long tons mined at the Granby colliery in 1940. Coal output was first recorded in 1909 and since that time fifteen properties are reported to have either mined coal or to have done prospecting or development work; of these, only two are presently active. However, none of the properties now inactive were closed because their coal resources were exhausted. The accompanying key map shows the extent of the Princeton coal field, and the location of the coal mines and prospects in this field General Geology The Princeton field is underlain by rocks of Oligocene age and is one of the series of more or less isolated Tertiary lake basins in which coal, or lignite, has been found in the interior of British Columbia. Resting on the Nicola group rocks of Triassic age, the Princeton sedimentaries consist of sandstones, conglomerates, shales, bentonite, bentonitic clays, and several seams of coal. Tertiary volcanics occur both above and below the stratified rocks and in places they have been thrust through the overlying measures. In some areas, the coal has been burned to a red ash as the result of vulcanism, while in other parts some of the moisture has been driven from the coal, thus improving the grade. The field can best be described by dividing it into two areas: the Southern area, lying to the south of the town of Princeton, where most of the mining has been done; and the Northern area, to the north of Princeton, where very little development has taken place.

Jan 1, 1947

By E. A. Gulbransen, W. S. Wysong

THE behavior of molybdenum and its surface oxides in oxidizing and reducing gas atmospheres and in high vacua at elevated temperatures is a question of scientific and technical importance The use of molybdenum as a metal or as an important component in alloys in oxidizing atmospheres at elevated temperatures has been limited because of the unprotective nature of its oxide film and the volatility of this oxide at moderate temperatures. This communication will present results of a vacuum microbalance study 1,2 of the following problems. (11) the oxidation kinetics in the temperature range of 250° to 450°C; (2) the reduction with pure hydrogen of thin oxide films formed on molybdenum; (3) the volatility of the thin oxide films, and (4) the vacuum oxidation of molybdenum at high temperatures. Molybdenum is an interesting metal to study for the following reasons: (I) although the oxide-to-metal-volume ratio is greater than one, the metal is not considered protective; (2) the metal oxidizes readily at temperatures of 250°C and higher; (3) the oxides of the metal are reduced at temperatures as low as 500°C by pure hydrogen; (4) the oxide MoO3 melts at 795°C; and (5) the oxides of molybdenum are volatile at moderate temperatures. The following variables are studied in the oxidation kinetics. time, temperature, pressure, surface preparation, surface area, concentration of inert gas in the lattice, cycling procedures in temperature, vacuum effect and high temperature vacuum oxidation The general interpretation of many of these factors has been previously discussed. LITERATURE The oxidation of molybdenum has not been studied critically. Although" many studies have probably been made on the kinetics of the oxidation process, none has been reported in the literature available to us. The crystal structures found in the oxidation of molybdenum have been studied by Hickman and Culbransen 4 Their results showed that MoO2 is the oxide which is stable in contact with the metallic subgtrate throughout the temperature range 300 to 700°C. As the film thickens in the low temperature range, MoO3 becomes predominant on the surface. Above 400°C, Mo03 is no longer observed, Mo02 being the only oxide found. Hagg and Magneli5 have shown from an X ray study that the a-phase, orthorhombic MoO3 is stable up to 1050°C. Two other phases, ß and ß', with compositions close to Mo02 90 are also obtained The formula for the ß phase is not given but that of the ß' phase is defined as Mo9026. The ß' phase is found to be built upon a monoclinic unit cell. A -?-phase is isolated from a preparation M00275 heated for 17 hrs at 670°C. This phase is

Jan 1, 1947

By W. B. Mather

THE object of this paper is to record and interpret data collected during the examination of over 250 barite deposits in the Central Mineral District of Missouri. [ ] In the course of this study, the origin of the deposits, which the author believes to be hydrothermal, has been given particular attention. Economic barite deposits occur in two main areas in Missouri: (I) in the Washington County District of Southeast Missouri, from which over go pct of the state's production is derived; and (2) in the Central Mineral District, which includes portions of 15 counties in Central Missouri (Fig I). Barite in the smaller Washington County District is mined from widespread low grade, relatively shallow residual deposits, whereas in the Central District, it is mined

Jan 1, 1947

By Bever M. B., Floe Carl F., Hung Liang

Data on the solubility of hydrogen in iron-silicon alloys are of practical interest, as hydrogen causes gas unsoundness and embrittlement in iron and steel and is also a factor in the metallurgy of cast iron. Zapffe and Simsl have recently demonstrated that in deoxidized iron and steel castings gassiness and bleeding are primarily functions of the hydrogen content of the liquid metal. These authors also suggested convincingly that ordinary melting and casting practice provides several sources of hydrogen for absorption by the metal. Norbury and Morgan2 and Boyles3 have shown that dissolved hydrogen affects the graphitization of cast iron. Schneble and Chipman4 included in a study of the effects of superheating on the properties of cast iron an investigation of the part played by hydrogen. Schwartz, Guiler and Barnett5 investigated the significance of hydrogen in the metallurgy of malleable cast iron. A complete interpretation of investigations of this kind calls for equilibrium values of the solubility of hydrogen in the liquid and solid phases. From the theoretical standpoint, the solubility of gases, especially hydrogen, may reveal some aspects of the nature of liquid metallic solutions. This was implied in the early work of Sieverts6 on the effect of alloying additions on the solubility of hydrogen in copper. Recent work by Bever and Floe7 has shown that in liquid copper-tin alloys the solubility of hydrogen changes abruptly at the composition of the intermetallic compound Cu3Sn. It is of considerable interest to determine whether liquid alloys of iron also have compositions at which the solubility of hydrogen exhibits a discontinuous or otherwise unique behavior. Among the various alloys of iron the iron-silicon system is important because of the presence of silicon in various structural alloy steels, transformer sheets, cast irons and special acid-resisting castings. The various grades of ferrosilicon, finally, cover almost the entire remainder of the composition range. Published information on the solubility of hydrogen in iron-silicon alloys is meager. The first values for pure liquid iron were reported in 1910-191 1 sieverts and Krumbhaar8 and by sieverts.9 They found that 100 grams of iron absorbs 28 c.c. of hydrogen at 1550°C and One atmosphere pressure, and 31 C.C. at 1650°C. In 1938 Sieverts, Zapf and Moritz10 published a value of 26.3 C.C. at 1550°C. Data on the solubility of hydrogen in liquid iron-silicon alloys and in liquid silicon are not available. Martin1' investigated

Jan 1, 1947

By Norman Weiss

MOST papers on xanthate have dealt with principles rather than practice. On the assumption that many millmen are interested in knowing where and in what manner the xanthates are being used in mills other than their own, this paper will summarize the results of a recent survey of North American plants. A brief background story and a description of the xanthates will be followed with the results of that survey; then a few observations will be made on storage, feeding, and ore testing. The first xanthate was made in 1822 by Zeise of the University of Copenhagen. With commendable scientific detachment (or perhaps a bad cold) Zeise ignored a more pervading quality of the substance and named it for its color, after the Greek word "xanthos," meaning yellow. During the first 80 years of its recorded existence xanthate found use only in.small quantity as an insecticide; after the turn of the century there was some further demand for it in the vulcanization of rubber. It was not until 1922, by coincidence the centennial of Zeise's discovery, that C. H. Keller of San Francisco, seeking sulphidizing agents, recalled xanthate in connection with his experience years earlier when he had seen this material used in Europe to combat grape phylloxera. His successful tests with the new flotation reagent culminated in the basic xanthate patent (U. S. 1,554,216) in 1925. In the minds of many metallurgists the introduction of xanthate as a flotation reagent is identified with the beginnings of alkaline circuits, the first use of chemical collectors, and the beginning of selective flotation. Actually, these preceded xanthatc by a number of years. The alkaline circuit in lead-zinc flotation was introduced by Lyster as early as 1912. In 1922 Sheridann and Griswold made their momentous discovery (Timber Butte) that alkali cyanides and zinc sulphate effectively inhibited the flotation of pyrite and sphalerite in pulps made alkaline with sodium carbonate or bicarbonate. The use of lime to retard pyrite in copper flotation began within two years after Ralston directed attention to its possibilities in 1917. These were the beginnings of modern selective flotation, which was practiced successfully on copper-iron ores at Nacozari in 1922, and at Inspiration, Cananea, and others only shortly afterward. In the lead-zinc mills, selective flotation was of even greater economic importance at that time. The Sunnyside plant of U. S. Smelting, Refining, and Mining Co. used the process earlier than 1920, and Consolidated, Timber Butte, and others soon followed. As a chemical collector xanthate was relatively a latecomer, for the Corliss patent of 1917 covered the first of these, alpha-naphthylamine, and the Perkins patent of 1918 the second, thiocarbanilid. Both of these were in extensive use before Keller's xanthate made its commercial debut in 1923. There is general agreement, nonetheless, that the introduction of xanthate was

Jan 1, 1947

Jan 1, 1947

By Henry P. Ehrlinger

THE Alta and St. Louis mines of the Alta Mines, Inc., produce a somewhat oxidized ore with a talc gangue that presents quite a problem in milling. For several years the mill recoveries were relatively low and there seemed to be no cure for this condition even with increasing the various collecting agents and frothers to two or three times of what they should be. The usual alibi of "oxidized ore" was given as the reason for these results and the matter stood there for some time until these investigations were started. FLOWSHEET As a brief outline of the flowsheet the ore is crushed to minus I in. in a Telsmith jaw crusher and then fed to a 64 1/2 Marcy grate mill. The resulting product from the grate mill is passed over a trommel where the coarse particles (plus 7 mesh) are returned to the grinding circuit through the classifier. The under 7-mesh pulp is passed over two Denver mineral jigs where a high grade concentrate is produced, thence over two Wilfley tables where a table concentrate is produced and about 80 pct of the oxide lead recovered. The tailings from these tables are pumped back to the classifier and after classification the 30 pct pulp density product, which overflows the lip, is passed into a series of 10 Denver economy flotation cells where a lead-copper concentrate is produced. Three products are made and shipped to the smelter termed jig, table and float concentrates. RESULTS WITH VARIOUS REAGENTS In March of this year work was started on the metallurgical problems of the mill and, as is shown in Table I, the results obtained were not too efficient. [ ] Tests were run with various reagent combinations that were recommended for ores of this nature but there was no appreciable effect on the recoveries. The grades of the flotation concentrates were reduced by the insoluble picked up and retained by these more powerful collectors and frothers. RESULTS WITH "METSO" In past work on ores of this type the use of "Metso" had improved gold and lead recoveries, but no effect on the silver and copper recoveries had been noted. To

Jan 1, 1947

By H. I. Smith

CONTENTS [PAGE Problems of Mining and Processing Mineral Aggregates (TP 1649, by NATHAN C. ROCKWOOD, Min. Tech., Nov. 1943. Discussion by H. I. SMITH, IRVING WARNER and the author) t Mica in War (TP 1749, by RUSSELL G. WAYLAND, Min. Tech., July 1944. Discussion by H. S. SPENCE) 3 Three Roofing-granule Plants in Pennsylvania (TP 1787, by RICHARD M. FOOSE, Min. Tech., Jan. 1945. Discussion by H. I. SMITH)5 Methods of Prospecting and Mining Optical Calcite in Montana (TP 1896, by E. W. NEWMAN, Min. Tech., Nov. 1945. Discussion by W. C. STOLL and FRANK C. ARMSTRONG, and the Glass Sand and a Glass Industry in Puerto Rico (TP 1939, by HOWARD A. MEYERHOFF and J. EARL FRAZIER, Min. Tech., Nov. 1945. Discussion by A. M. SHORT, the author and PHILIP The "Bonanza" Mica Operation of Purdy Mica Mines, Limited, Mattawsn Township, Ontario (TP 2154, by HUGH S. SPENCE, Min. Tech., March 1947. Author's supplement and discussion by JOHN A. BAKER, E. J. LINTNER, and the author) 7 Process for Manufacture of Dead-burned Magnesite and Precipitated Calcium Carbonate from Dolomite (TP 2155, by ROBERT D. PIKE, Min. Tech., March 1947. Discussion by 0. C. RALSTON and the author) 9] Problems of Mining and Processing Mineral Aggregates H. I. SMITH*-Mr. Rockwood has presented a very interesting paper on problems of the mineral aggregate industry in meeting specification requirements, which apparently are ever decreasing in tolerance. May I call attention to a method of mineral separation that may be of value in separating the flat aggregate particles from the more angular ones and possibly the soft particles from the hard. The method is the old Pardee spiral coal separator, extensively used many years ago in the anthracite region for separating rock and bone from anthracite coal.1 The success of the process depends on the relative coefficient of friction of the aggregate particles to be separated rather than on their relative specific gravity. The flat and the soft particles normally will slide more slowly and stay on the inner spiral until they reach the delivery spout at the bottom whereas the round and the angular pieces will work to the outer edge and fall off into a spiral of larger diameter. The capacity of the separator is increased materially by having three inner spirals, with a separate feed for each, on which the particles travel more slowly, and one outer spiral from which the more rapidly traveling pieces slide to the bottom. IRVING WARNER*-I have long been convinced that much of the equipment and methods developed for mineral dressing might be advantageously employed in the mineral aggregates industry, and more particularly in the production of sand and gravel. The two industries are not well acquainted with each other or their problems. They have separate trade publications. The difficulty with the situation is that there are few large sand and gravel plants and few provided with technical services in their own organization or by retainer. This does not refer to engineering organizations but rather to improvement of plant technic in processing.

Jan 1, 1947

By Enid C. Plante

THIS paper deals with the flotation of the mineral fluorite (calcium fluoride) and of two associated gangue minerals, calcite and quartz. The aim of the investigation was to produce "acid-grade" fluorite, which must contain less than one per cent of silica. Several reagents are used successfully in practice for floating fluorite from its ores. Oleic acid is the most widely used collector, usually at temperatures above 60°C, with sodium silicate as a dispersant for quartz and quebracho or tannin to depress calcite. Sulphides (e.g., galena) are often removed first by xanthate flotation. Many investigators23 report results in which more than 80 pct of the fluorite is recovered in a concentrate assaying 96 pct or more of fluorite and less than I pct of silica. This investigation was undertaken with the intention of floating the gangue, which is the minor constituent of the ore, from the fluorite. Hence emphasis was first placed on the cationic compounds that float quartz. No satisfactory separations were obtained in this way, and other reagents were investigated to discover whether these were more effective than oleic acid in floating fluorite from quartz in the usual way. The first part of the paper describes experiments with several long-chain collectors available commercially. Most of this work has been by captive-bubble and cylinder flotation tests, with some batch tests in a flotation machine. The second part describes the use of sodium cetyl sulphate as a collector for fluorite and includes laboratory tests and extension of the work to batch tests in the flotation machine. A method for determining the adsorption of sodium cetyl sulphate on fluorite has been developed and is described. Theory of Collection by Paraffin-chain Salts It may be assumed that these compounds are adsorbed at the mineral surface in one or more of three ways outlined by Kolthoff :12 I. Exchange adsorption between lattice ions in the mineral surface and collector ions in solution. Closely related is adsorption by the collecting mechanism postulated by Taggart,17 in which there is metathesis between the collector and the mineral cation or anion. 2. Exchange adsorption between adsorbed gegen ions (p. 67, ref. 19) and collector ions in solution. 3. Adsorption of nonelectrolytes (polarnonpolar) without displacement of adsorbed ions. With cationic collectors, inorganic cations in the solution (e.g., hydrogen ion) compete with the collector ions and therefore act as depressants, while inorganic anions have the same effect with anionic collectors. From this follows the general conclusion that ions of the same charge as

Jan 1, 1947

By Edward F. Fitzhugh

QUANTITATIVE appraisal of the chances of finding various tonnages and grades of ore clarifies any exploratory development proposal. Ways are discussed of appraising chances in conformance with probability principles, and graphs are suggested to show tonnages, grades and the corresponding judged expectancies.

Jan 1, 1947

By F. C. Sturges

[CONTENTS PAGE ................. Introduction-Grouting in Mines. By F. C. STURGES. I Use and Technique of Pressure Grouting in the Construction Industry. By V. L. MINEAR . 3 Technique of Pressure Cementing in the Petroleum, Mining, and Construction Industries. By WY. D. OWSLEY and R. E. MOELLER. ..................... 9 An Example of Controlled Pre-grouting in Shaft Sinking. By R. H. ALLEN and J. W. GALPIN. 15 ........ Solidifying Mines and Shafts Areas by Pressure Grouting. By B. H. MOTT 17 .............. Grouting in Southeast Missouri District. By W. W. WEIGEL 20] Introduction-Grouting in Mines By definition the word "grout" means a thin mortar, or a kind of plaster or cement, and "grouting" means to fill up or finish with grout. The words "cement," "plaster" and "mortar" mean a substance that is used in a soft state which subsequently hardens. Thus, grouting is the filling of void space with a substance that hardens. Construction cements are the most common substances used, either by themselves or in mixtures, but the term grouting is applied quite correctly when other substances such as plastics and certain chemicals are used. Also, the use of the term grouting to cover the filling of voids with materials that do not actually become hard, such as the flotation tailings used in grouting in the southeast Missouri lead district, should be considered correct, as some stiffening does take place and, anyway, it is a better descriptive term than any substitute. Engineers are interested in grouting because some of the materials with which they must work contain voids, and certain conditions can be improved if these voids can be filled with something solid and permanent. Grouting is done to accomplish several purposes: I. To stop the passage of fluids and gases, 2. To cement materials together to make them stronger, and 3. To prevent consolidation of materials by filling void space with something solid as a replacement for the air and water that could be forced out under load. The construction industry uses grouting extensively for all three purposes. Grouting is used to stop water percolation under and around dams. It is used to control water flow in tunnel driving and in shaft sinking. It is used to improve foundation conditions under civil engineering structures by permanently filling void space and thereby reducing settlement, or by cementing broken rock together and increasing its supporting strength. The oil and gas industry does a lot of grouting, primarily to stop the passage of gases and fluids. The search for oil at increasingly greater depths has meant greater investment per well, and the oil industry has spent large sums on development of improved drilling methods. This

Jan 1, 1947

By W. B. Boggs

This is a rather comprehensive subject and cannot be thoroughly covered in the short rime allowed for its presentation. This article will touch only upon a few of the chief points of the difficulties encountered in recovering copper from brass shell cases in a primary smelter which was not designed to treat scrap metals. Owing to the fact that the plant is at present (Dec., 1946) closed, and our tests were not completed, full details of the results are not available. As is well known, most primary smelters are situated near the mines in the interior of various countries and are not close to seaports or large industrial and railway centres. Consequently, iris unusual for a primary smelter to be asked to treat scrap metal of any kind. When so required, iris obvious that the primary smelter is at a great disadvantage, for the simple reason that it probably has to pay the freight on the scrap from the seaport or industrial centre to the smelter and then also pay the freight on the recoverable metal from the smelter to the refinery, or seaport or industrial centre. Another disadvantage is that a primary smelter is not equipped to sample and unload the scrap nor bas it usually the equipment adaptable for treating the scrap efficiently, as the plant bas been designed to handle large tonnages of ores and concentrates. This short paper will describe some of our difficulties> and how they were corrected. However, it might be advisable to state briefly some of the methods used in treating brass shell cases in other plants. In the first place, a brass plant producing new brass- especially those producing brass billets for extrusion to make brass tubes or rods, or to be drawn into wire, or making brass cake to roll into brass sheets- generally insists upon using new electrolytic copper and zinc and is opposed to using any scrap or secondary brass . Consequently, such a plant usually will not treat brass shell cases. Therefore, the usual procedure is to ship brass shell cases to a secondary smelter, where it is generally sorted, melted, fire-refined, and returned to the market in the form of a high or low brass ingot which can be sold to brass foundries for making brass castings. This evidently is the cheapest and simplest method. Another method is to ship to a smelter which is a combination of a primary and secondary smelter attached to or near an electrolytic refinery. In plants of both these types, that is a primary smelter with Cottrell dust collectors or a combined primary and secondary smelter with Cottrells or a bag house, the zinc may be wasted. However, if a bag house is used, some of the zinc is recovered, but it is usually contaminated with other metals and further processing is required to recover it.

Jan 1, 1947

By A. D. Schwope, L. R. Jackson, A. M. Hall

IN the course of an extensive investigation of the comparative properties of several types of copper, data were obtained on the cold working and subsequent recovery and recrystallization of the copper. In this paper, relations between the degree of cold work and the course of recrystallization are developed. In particular, it is shown that the course of recrystallization over long periods of time and at low temperatures can be predicted with reasonable accuracy from short-time high-temperature recrystallization data. MATERIALS USED IN THE INVESTIGATION Three types of copper were used in this investigation; these were tough pitch, OFHC, and OFHC copper with 15 oz per ton of silver added identified herein as Lots C, D, and F, respectively. The material was supplied by the American Metal Co. Ltd., and processed by the Rome Cable Co. The analyses of the three types of copper are given in Table 1. Originally, it started as wire bars 4 X 4 X 54 in. These bars were heated to 871°C in air and hot rolled to 3/8 in. rod. This rod was cold drawn to 0.204 in. rod (70 pct reduction) in three passes and annealed at 427°C for 4 hrs. A portion of the 3/8 in. rod was saved for more detailed cold-drawing experiments. Starting with the annealed 0.204 in. rod, hard-drawn wires were produced by cold drawing to 0.081 in. wire in 7 passes (84.4 pct reduction in area). Half-hard wires were made by cold drawing the 0.204 in. rod to 0.102 in. wire, (75 pct reduction) in 6 passes and annealing at 427°C for 4 hrs. This annealed wire was then drawn to 0.081 in. wire, (37.1 pct reduction) in 2 passes. Square rod was made by hot rolling wire bars to 9/16 in, rod in 8 passes. This rod was then cold drawn to 0.445 in.-diam rod and annealed for 3 1/2 hrs at 538°C. It was then cold drawn to 0.325 in. rod and again annealed at 538°C for 3 1/2 hrs. Hard square rods were then made by cold rolling this material to 0.257 X 0.257 in. rod, a reduction in area of 20.5 pct. Half-hard square rods were made by cold rolling to 0.268 X 0.268 in. square, annealing for 332 hrs at 538°C and cold rolling to 0.257 X 0.257 in., a reduction of 8.5 pct. Soft wire or rod was made from all types of copper by annealing the hard-drawn material at 343°C for 3 hrs in steam. The grain size of the annealed 0.081 in. wire varied slightly among the three lots: from 0.015-0.025 mm in the silver-bearing OFHC to 0.035-0.045 mm in the OFHC copper. The annealed 0.257 in. wires were more uniform in grain size, averaging about 0.035-0.045 mm. Representative structures are shown in Fig I. EFFECT OF COLD DRAWING AND TENSILE STRAIN ON STRENGTH OF COPPER Conventional tensile tests were performed on the three types of copper in the various degrees of hardness described above. Results of these tests are tabulated in Table 2. The results in Table 2 are

Jan 1, 1947

By A. E. Dyment

In formulating an explosive for any specific set of conditions, various factors must be taken into consideration. Is it to be subjected to water or moisture? .If so, it must be designed to have an inherent ability to resist water. Is it to be used in confined spaces underground, where ventilation is limited? If it is, it must possess qualities enabling it to form, upon explosion, the minimum quantity of noxious gases, such as carbon monoxide or oxides of nitrogen. Is it for use where low temperatures may possibly prevail? If so, it must be capable of resisting such temperatures without freezing. Is it for use where dust or inflammable gases may be present? If it is, then it must be so formulated as to produce, upon detonation, a flame of the lowest possible temperature and the shortest possible duration, in order to lessen the chance of ignition of such gas or dust. This is actually the essential property of a permitted explosive, and it is undoubtedly the most important characteristic of an explosive which is to be used in gassy or closed-light mines. This being the quality that distinguishes permitted explosives from other types, it is interesting to investigate the ways and means by which the low-flame-temperature characteristic is obtained . Generally speaking, such explosives are so designed as to contain comparatively small quantities of nitroglycerin and relatively large quantities of the strength-producing salt, ammonium nitrate. This ingredient does not develop as high a temperature upon explosion as does nitroglycerin, so its presence, in large measure, in place of nitroglycerin results in an explosive which has an inherent low-flame-temperature characteristic, as opposed to one which is .made up largely of nitroglycerin, which would ordinarily be in the high-flame-temperature class. Additions are also made of flame-quenching salts such as sodium chloride, ammonium chloride, and up to a certain limiting percentage of sodium nitrate. These salts, with the exception of the last, do not ordinarily take an active part in the explosive reaction, being present primarily to absorb heat liberated by the reacting ingredients.

Jan 1, 1947

By Frederick C. Hull

THE grain size of a metal or alloy is one of the most important factors determining its properties. In steels, for example, grain size affects hardenability, toughness and machinability; in brasses, grain size is related to hardness and deep-drawing quality. In the field of heat-resistant alloys, grain size has a marked effect on ductility, creep and endurance strength. In order to determine these effects, as well as to control the properties of materials, many accurate and rapid measurements of grain size must be made. This paper presents a new and improved method for the estimation of grain size. USUAL METHODS of EVALUATING GRAIN SIZE A frequently used method of estimating grain size is that of comparing the image of a polished and etched specimen on the ground-glass screen of a metallographic microscope with standard grain-size charts. Several types of standards are available for use with different classes of microstructures. Geometric Grids.-The Metals Handbook1 has a series of hexagonal grids ranging in size from ASTM No. I to 8. Idealized Grain Networks.-Idealized grain-boundary networks for ASTM grain sizes I to 8 are included in the American Society for Testing Materials Tentative Standard E19-39T. Standard Micrographs.- The Metals Handbook and ASTM Tentative Standard EI9-39T contain micrographs of hypoeutectoid and hypereutectoid steels ranging in grain size from No. I to 8. The grain size of annealed brass (diam¬eter of the average grain in millimeters) is obtained by comparison with 10 micrographs of varying grain size in ASTM Tentative Standard Es-39T. A handicap to accurate evaluation of grain size by this method is the fact that it is difficult to compare photographs in a dimly lighted room with the image on the ground-glass screen, or, if the general illumination is increased so that the printed standards may be clearly seen, the contrast of the image of the unknown is decreased. It is easier to estimate grain size by comparing a micrograph of the unknown with the grain-size standards. However, photographing every specimen on which the grain size is desired is too costly in time and materials to be practicable. For hardened steels, the Shepherd or Jernkontoret fracture grain-size standards are very accurate and useful, but this method obviously cannot be applied to ductile alloys such as brass, stainless steels and austenitic heat-resistant alloys. Jeffries' method for grain-size measurements consists of counting the number

Jan 1, 1947

By J. R. Long, T. R. Graham, R. S. Dean

FOLLOWING the development of elec¬trolytic manganese production by the Bureau of Mines, an extensive program was planned to study the character of this high-purity product and its possible utilization in various alloy combinations. Previous work reported in the literature concerning alloys containing substantial amounts of manganese dealt largely with material prepared from relatively impure grades of the metal, and in many instances the impurities thus introduced did not permit true evaluation of manganese as an alloying element. One phase of the Bureau's program included a general review of the system and the establishment of the physical properties of copper-manganese-zinc alloys, using electrolytic manganese, and with particular emphasis directed to com¬positions within the alpha solid solution area. A number of reports of the work on alloys in this system, giving specific data concerning the equilibrium system and some of its alloys, have already been published. One study1 established the alpha solid solution area at various temperature levels and composition ranges up to 50 pct manganese. Other investigation reports presented the properties of selected alloys; namely, a 65 pct copper, 10 pct manganese, 25 pct zinc alloys' a sensibly white manganese brass composed of 70 pct copper, 20 pct manganese, 10 pct zinc,3 and a series of alloys with a constant copper content of 60 pct and 5 to 25 pct manganese, balance zinc.4 In these reports tensile properties as influenced by cold-working and subsequent annealing were given in detail. Additional data are now available on other alloys of the alpha region up to 50 pct manganese, and these, together with previously published information, are sufficiently complete to establish the relationship between properties and composition for this portion of the ternary system. The present report is a summary of the tensile properties of wrought alloys in the form of sheet and rod stock. The summary is necessarily limited to data for only one condition of cold-work and a single annealing temperature, since a complete exposition of all the data available would be too extensive for this presentation. Nevertheless, it is possible to make a reasonable approximation of the tensile properties in other conditions of cold-working and annealing by a correlation of the data previously presented on specific alloys and the data given here.

Jan 1, 1947

By Frank R. Milliken

SCOPE THIS paper is a running commentary on metallurgical problems and developments, stressing ilmenite flotation, since the start of operations five years ago, at the mill of National Lead Company, Titanium Division, Maclntyre Development, Tahawus, New York. [ ] GENERAL In early 1941, when, world conditions threatened to cut off the supply of ilmenite (obtained largely from India) to this country, the National Lead Company started to develop and bring into production their Maclntyre Development. This operation supplied the bulk of the ilmenite used during the war period for the manufacture of the much needed titanium pigments. Maclntyre Development is at Tahawus, New York, on the headwaters of the Hudson River in the center of the scenic Adirondack Mountains. A general description of the operation was given in the Adirondack Issue of Mining and Metallurgy for November 1943. Operating tonnages and production have increased since 1943, however. Nearly 10,000 tons of ore and waste is broken and loaded daily in the open-pit mine. About half of this tonnage is ore, from which is produced nearly 800 tons of ilmenite concentrate and 1600 tons of magnetite concentrate daily. ORE-TYPES From an ore-dressing standpoint, there are five rather distinct ore types and two waste-rock types in the mine. The ore types are shown in Table 1. The anorthosite waste is a coarse-grained white rock, largely labradorite feldspar. The gabbro waste is generally finer grained, and contains, in addition to feldspar, 35 to 75 pct iron silicates such as hornblende, pyroxene, garnet and biotite. A minor mineral mineralogically, but important metallurgically, is apatite. A few calcite

Jan 1, 1947

By Kenneth C. Vincent, A. M. Gaudin

In a study1 of the action of amyl xan-thate on chalcocite in water suspension, it was found that if the xanthate is added in relatively large quantity the xanthate group can be accounted for in three forms: (1) as xanthate ion remaining in water, (2) as benzene-soluble cuprous xanthate on the chalcocite, (3) as a benzene-insoluble coating on the chalcocite. Reduction in the amount of xanthate added leads to disappearance of form I then of form 2. With minute quantities of added xanthate, substantially all the reagent is of the "unleachable" kind. Yet this unleach-able xanthate can be dissolved by pyridine to form a soluble cuprous xanthate complex, and it is sufficient in effectiveness to make chalcocite flotable even if insufficient in quantity to form a complete mono-molecular film on the mineral. In that study it was also found that chalcocite abstracts cuprous xanthate from benzene so1ution, in what may (or may not) be a case of molecular adsorption. It seemed desirable, therefore, to study further the "unleachable" xanthate on the chalcocite, and particularly to ascertain whether it is formed as a result of the benzene leach or is actually formed during the conditioning of chalcocite in aqueous xanthate solution. A 'splendid tool to make such studies has recently been perfected; that is, the use of radioactive spies or tracer atoms. With this tool, it was thought possible to answer the problem stated above, but, unfortunately, this did not prove to be true. Answer to the flotation question was clouded by the existence of rapid and selective diffusion of copper atoms in the solid mineral—a phenomenon that was totally unexpected yet remains interesting and perhaps important. Method of Radioactive Spies The method of radioactive spies is discussed in many places. Two convenient references are the article by Evans2 and the book by pollard and Davidson.3 The method was first developed by van Hevesy and paneth in 1013, when only natural radioactive isotopes were available. These isotopes are few in number, and so the method remained limited in scope. Recently the synthesis of over 350 active isotopes of all the known stable chemical elements4 has opened widely expanded possibilities for the method, A fundamental tenet of the method is that a radioactive atom and a nonradio-active atom are exactly alike until disintegration of the radioactive atom. Then, by its sudden death, the spy reveals its location. The relative abundance of spies at various locations makes it possible to ascertain the relative abundance of the corresponding nonradioactive atoms at the same times and locations. A second fundamental tenet of the method of radioactive tracers is that the radioactivity lies in the nucleus of the atom: transfer of radioactivity from one

Jan 1, 1947

Jan 1, 1947

By J. Rogers, K. L. Sutherland

The relationships between collector and mineral, activator and mineral, and activator, collector and mineral will be considered herein. We propose to criticize current theories of flotation but we will not repeat the many pertinent arguments presented by Wark and Cox28 in 1937 in which the "chemical" or more strictly the "solubility" theory proposed by Taggart and co-workers22 is shown to be untenable. Recently Taggart, Arbiter and Kellogg24 have studied the long-chain aliphatic amines as collectors and have attempted to resuscitate the solubility theory for these particular collectors. Dean and Ambrose3 have felt that "we stumble over words" when we distinguish different mechanisms of adsorption. Our view is that nothing is more stultifying to the development of a science than attempts to force widely different phenomena into one classification. This oversimplification leads immediately to difficulties in the interpretation of results. Experimental Procedure The response of minerals to activator and collector was determined by "captive-bubble" tests. The methods of preparation of specimens26 and of testingin have been previously described. Results from captive-bubble tests were confirmed by flotation tests in glass-stoppered cylinders.26 The full lines shown in the figures relating solution composition to contact (flotation) distinguish solutions in which contact (flotation) is possible from those in which it is not. The curve is derived by successive approximation and the accuracy is ±o.2 pH units and ±5 mg. per liter of collector or depressant. Solution compositions for which it was shown experimentally that contact or flotation is possible are marked by a circle, those for which it is not possible by a cross and those for which it is doubtful by a cross within a circle. It is assumed that at all other solution compositions within (without) the curve, contact or flotation is possible (not possible). After testing in the collector solution, the mineral was removed, washed, and tested by the captive-bubble method in water, or floated in a cylinder with frother only. In this way the composition of solutions in which a mineral was conditioned but in which properties of the collector solution prevented contact or flotation can be defined. The composition of solutions in which conditioning was possible lie between the full and broken curve, the experimental results being indicated on the figures by a square. The curves show the limits of composition of solution in which flotation in a cell would be possible. Many factors other than those considered in these tests determine recovery or grade of a given mineral in practice.

Jan 1, 1947