Search Documents

By Sidney Siegel, J. Gardner Brooks, Irvin R. Kramer

IN 1942 Grossmann1 proposed that the hardenability of a steel may be calculated from its chemical composition by considering the base hardenability associated with its carbon content and grain size and multiplying this base by factors for each element present. Since Grossmann's original publication, several investigators2-5 have reexamined the multiplying factors for the individual elements and in general have found that the multiplying principle is valid. However, some of the individual factor curves developed have been in poor agreement. Inasmuch as the carbon-factor curve obtained by Grossmann was dependent [ ] upon the factors for all the other alloying elements present in the steel, it logically followed that his results were in need of correction in the light of the new data available for manganese, silicon, and the other alloying elements. Furthermore, in order to avoid the possibility that errors in the manganese, silicon, or other curves might influence the carbon-factor curve, investigation of iron-carbon alloys containing little or no manganese and silicon was necessary. That the effect of carbon on hardenability was greater than indicated by Grossmann is shown by a comparison of the diameters of completely hardened rounds of iron-carbon alloys with the ideal critical diameter calculated from Grossmann's factors. These alloys have a greater hardenability in a hite quench than predicted by Grossmann's factors for an infinite quench (Table I). [ ] Among the other important variables that were in need of further investigation were the effect of deoxidation practice on the grain-size correction curves and the effect of stable carbide-forming elements on the depth of hardening. Most of the work by Kramer, Hafner, and Toleman4 was done on silicon-killed steels. It was not known whether Grossmann's grain-size correction curves, deter- mined on aluminum-killed steels, was valid when applied to steels with different deoxidation practice. More data on the

Jan 1, 1946

[MININQ METHODS WILLIAM J. COULTEB, Chairman PHILIP B. BUCKY, Vice-Chairman LELAND A. WALKER, Vice-chairman ) CLYDE E. WEED. Vice-Chairman CHARLES F. JACKSON, Secretary]

Jan 1, 1946

By R. Floyd Farris

A method is presented for determining minimum waiting-on-cement time, which takes into account the differences that exist between types and brands of cements and such individual well conditions as depth, temperature, and pressure. The basis for the method was determined by laboratory tests. Being a laboratory development, several steps were required to prove its merit. The first step consisted of laboratory tests designed to determine the minimum cement strength required in wells. Basis was found for setting a minimum value of 8 Ib. per sq. in. tensile strength. Next, it was shown by laboratory tests that the time to 8 Ib. per sq. in. tensile strength may be expressed as a function of consistometer stirring time to loo "poises," the approximate relation being "the time to 8 Ib. per sq. in. tensile strength equals the time to I00 'poises' times three." Next, it was shown that the time of maximum temperature development in cement slurries, due to heat of hydration, is also related to consistometer stirring time to loo poises, but only by a factor of approximately two. It was shown also that the shut-in casing pressure will build up after cement is placed and register a maximum pressure at approximately the same time the slurry down the hole attains maximum temperature. From this and the relationships listed above, the general rule was established that minimum waiting-on-cement time (time to 8 Ib. per sq. in.) after casing cement jobs in any well is equal to the time when the shut-in casing pressure reaches a maximum, as measured from the initial mixing of cement, times a factor of 1.5. Cement plugs drilled in the field at the time prescribed by this formula were found to drill "firm to hard," thus confirming the laboratory tests. These tests prove that many of the present regulations for waiting on cement require a longer time than is absolutely necessary. Use of the method herein proposed offers the possibility of a saving of $1200 per well. Introduction The length of time allowed for cement to set after casing is determined either by state-wide rules, field rules, or self-imposed rules written into drilling contracts. In general, the time is dictated by experience and common practice. However, owing to differences in opinion and in experience of the various groups involved, waiting-on-cement time often varies from one area to the next. For example, an operator in an area where no rules exist may drill out of surface pipe at 24 to 36 hr., while another operator in another area may wait 48 hr. or more to comply with state or field rules, although the depth of the well, hole size, type of cement, and other data are identical. An even greater difference in practices will be found by making similar comparisons with respect to oil-string cement jobs. Differences in waiting-on-cement times of 36 to 48 hr. are common. Further complicating the picture is the rather common practice of allowing more waiting time for cement to set at the greater depths than is allowed at the shallow depths. This practice has existed for years in spite of the common knowl-edge1,2,3 that the temperature of the earth at the usual setting depths of surface

Jan 1, 1946

Jan 1, 1946

By John I. Yellott

SINCE the days of Newcomen and Watt, when men first sought to turn the energy of fuels to useful purposes, coal-generated steam has supplied most of the power needed for both stationary and mobile applications. The low efficiency and large water requirements of the nineteenth century steam-power plant caused many engineers to turn their thoughts toward more direct means of converting heat into power. As far back as 1791, John Barber secured an English patent on a combination' which he might well have called a "gas turbine." He proposed to generate procducer gas from coal or charcoal, to burn it under pressure in air obtained from a reciprocating compressor, and to drive a turbine wheel with the resultant hot combustion products. With the optimism characteristic of the inventor, he hoped that the turbine would not only operate his compressor but also perform useful work. There is no record that Barber ever built his machine, but if he had done so he would have learned that useful power can result from such a combination only when both turbine and compressor are highly efficient and when the temperature of the gas entering the turbine is not far below 1000°F. Hot-air prime movers continued to attract attention, and both Stirling in England and Ericsson in America2 built reciprocating engines that operated with some success upon coal-heated air. The internal-combustion engine, burning liquid fuels, supplanted the hot-air type, and, for the first time, challenged the supremacy of both the steam cycle and its familiar fuel, coal. LIQUID FUELS COMPETE WITH COAL As the increasing use of the automobile multiplied the demand for gasoline, the supply of residual fuel increased rapidly, and heavy oil declined in price to the point where it became competitive with coal. First in the marine field and later in stationary plants in areas adjacent to refineries, oil began to be widely used. Oil's greater convenience and higher heating value per pound of weight or per cubic foot of bunker space have caused it to take over much of the marine field. The introduction of the highly efficient diesel engine, capable of burning a fuel that is cheaper than gasoline, again threatened the position of coal, for the operating costs of the diesel became directly competitive with those of coal- burning equipment. In isolated power plants and smaller marine installations, the diesel provided the medium by which oil again successfully invaded fields formerly dominated by coal. The diesel engine, provided with an

Jan 1, 1946

By Fred J. Wright

ORIGINALLY, mining machines were actuated by purely mechanical mechanisms comprising cams, levers and gear trains, which became more and more complex as demands were made for additional operations that would increase mine tonnage. To simplify these intricate machines, development engineers began utilizing the principles of high-pressure hydraulics long employed for the control of various machine tools. The resulting specificially developed hydraulic systems are now literally the heart of the mining machine. During World War No. 2, very little fundamental change in design was made in existing mining machines, but because of the recognition of the merits of hydraulic application to the machines of war, it is reasonably certain that hydraulics will be applied to mining machines in the future to a much greater extent. This potential future indicates that a more thorough knowledge of hydraulics and its maintenance must be incorporated in mine operation. Contamination of Oil Maintenance of high-pressure hydraulic equipment varies considerably with respect to mine practice and conditions. The success or failure is largely dependent upon the hydraulic fluid and its care. Since all successful hydraulic systems have been designed around the use of mineral oil as the fluid, a complete analysis of this prime factor should be made to make clear the requirements of the fluid in a hydraulic system. Contamination of Oil Manufacturers of mining machinery usually have specified an S.A.E. rating or viscosity index of the, proper mineral oil for use with their respective machines without considering the fact that many oils will meet these specifications but will not give the desired life or efficient operation. Hydraulic fluid should be specified as a good grade of mineral oil, such as turbine oil, having rust and oxidation resistance. It must have high chemical stability, high lubricity, and proper viscosity. These factors will minimize maintenance costs by reducing wear and the consequent replacement of parts, and at the same time will lower costs for the oil by extending its life. Bulk purchases of oil should be limited to small sealed containers provided with a proper pouring spout, thus reducing the possibility of contamination of the oil before it reaches the mining machine. The introduction of foreign matter, such as sand, water, coal dust and residue oil left in filling containers, will cause untold damage and maintenance expense. Sand, being one of the best natural abrasives, will soon wear the close tolerances of the various hydraulic mechanisms to an extent that will necessitate complete replacement. Water is considered normally insoluble in oil, but because of the churning action of a hydraulic system water is broken down to particles so small that they remain in suspension. This suspension is known as

Jan 1, 1946

By J. Murray Riddell, George A. Morrison

This paper is a companion to the one by George A. Morrison on Mining a Deep Limestone Mine in Ohio.‡ Barberton is 8 miles west of Akron, Ohio, and 23 miles south of Cleveland. The underground mining of limestone at Bar-berton constitutes the world's deepest limestone mine. The stratigraphy is as follows: 0-20 ft. Loam, clay, sand and gravel. Water bearing. 2-40 ft. Fractured sandstone. Water bearing. 40-110 ft. Sandstone with interbedded shale, slightly fractured. Water bearing. 110-314 ft. Sandstone with interbedded shale, slightly fractured. Water carrying. 314-2197 ft. Shale with occasional seams of sandstone, which varies in thickness from a few inches to 4 feet. Dry. 2197-2247 ft. Limestone. Dry. 2247-2742 ft. Dolomitic limestone. Dry. 2742-2767 ft. Salt. Dry. 2767- Dolomitic limestone. Dry. All of the strata dip to the southeast, about 0.5 per cent from the horizontal. The top 110 ft. of the crust is water-bearing. The rock strata are naturally fractured to a depth of 314 ft., sufficient to allow the passage of water. In the shaft-sinking operations, a stra- turn of oil-bearing sandstone one foot thick was encountered at a depth of 520 ft., and flows of methane gas were pierced at depths of 1350 and 1952 feet. Specifications for the mine plant called for, in part, the sinking of two vertical shafts and a hoisting plant capable of producing at the rate of 300 tons per hour. No. I shaft is 550 ft. west of No. 2 shaft. Each shaft measures 8 by 17 ft. outside of steel. General features of the design (Fig. I) are: Principal set members, 6-in. H-section; connecting angles (studdles), ? by 4 by 4-in. angle irons; spacing of sets. 8 ft. centers; spacing of bearer sets, generally, 160 ft.; bearers, of 12-in. I-beams. Each bearing set featured a concrete ring about the periphery of the shaft, steel to rock, and 8 ft. in height; permanent guides, 6 by 10-in. long-leaf yellow pine, 85 per cent heart. The Shaft-sinking Operation The preliminary shaft-sinking work consisted of driving interlocked steel piling about the exterior of the shafts to depths of 35 and 32 ft., respectively, and of such horizontal dimensions as to ultimately permit the pouring of a concrete collar 2 ft. in horizontal thickness. Following the pouring of a shaft collar, a temporary wooden headframe for shaft-sinking purposes was erected. The head-frame, while ordinary, featured: (1) a storage pocket of 300 cu. ft, capacity with truck servicing facilities, and (2) pneu matically operated dump doors, which mere actuated by the hoistman, thus caring

Jan 1, 1946

Jan 1, 1946

By J. R. Long, T. R. Graham, R. G. Feustel, R. S. Dean

The comprehensive study of the copper-manganese-zinc alloy system in the Bureau of Mines Laboratories has so far been principally concerned with alloys that lie within the alpha solid solution field of the system. Two regions, one centering about 65 per cent copper, 10 manganese and 25 zinc, and the other centering about 70 per cent copper, 20 manganese, 10 zinc, have been carefully examined. These have indicated that when the alloys are made with electrolytic manganese considerable amounts may be readily introduced and that the strength and hardness are increased without excessive losses in ductility. In the course of the work of establishing the limits of the alpha solid solution range,3 enough of certain of the alloys was prepared to permit determination of their- physical properties at a future date. The 60 per cent copper alloys concerned here are part of that series. They cross through the alpha field and into the adjacent alpha plus beta and alpha plus X fields, and are of interest because they offer some information on the effects of manganese on alloys lying in these fields. Composition and Fabrication of Alloys The chemical composition of the alloys involved is given in Table I. They were intended to contain 60 per cent copper with manganese increasing from 5 to 25 per cent in 5 per cent steps and zinc decreasing from 35 to 15 per cent. The analyses are so close to the intended composition that the alloys mill be referred to hereafter by their norninal compositions. They were finished into sheet by cold-rolling and intermediate annealing procedurzs calculated to produce sheet $i6 in. thick, cold-reduced by 20, qo, 60, and 80 per cent in thickness. Physical properties were determined on standard flat tensile specimens with 4-in. gauge length, although the test gauge section used was 2 in. The properties were obtained on cold-worked material and on material annealed at temperatures ranging from 700' to r500°F. after 60 per cent cold reduction. Since an annealing temperature of 1200°F.

Jan 1, 1946

By Clarence Zener

[ ] THE present investigation started in an attempt to understand certain details of the decomposition of austenite, and of the effect of alloying elements thereon. As the investigation proceeded it became apparent that not only these details, but all the general features of austenite decomposition, could be understood in terms of fundamental physical principles. Since the direct applicability of these physical principles has not been previously recognized, it was decided to incorporate the original results of the investigation into a review of the general subject of the kinetics of austenite decomposition. This review constitutes the present article. An extended summary of the results is given on pages 27 to 30. This article, which deals with the kinetics of phase transformations, may appropriately be considered as a sequel to two recent articles1,2 from this laboratory on the equilibrium relations in medium alloy steels.

Jan 1, 1946

By W. S. Holt, E. T. Tkac, R. A. Grange

QUANTITATIVE knowledge of the time element involved in austenite transformation in a particular steel provides a sound basis for understanding and planning heat-treatment. Such knowledge is conveniently obtained by measurement of austenite transformation as it occurs at each of a series of temperature levels. The results of these measurements usually are summarized in the form of the now familiar isothermal transformation diagram (I-T diagram, TTT diagram, or S-curve). Although a considerable number of such diagrams already have appeared in the literature, there remain many compositions of commercial importance for which no I-T diagram is available. The diagram for many such steels may be predicted from published data with sufficient accuracy for most practical purposes, but for others no satisfactory prediction can be made because the effect on austenite transformation of one or more of the important alloying elements present is not well enough known. Such a steel is Nitralloy, Type 135-Modified, which, containing about 1.25 per cent aluminum, differs from any whose I-T diagram has been published. This paper presents results of a study of the isothermal transformation behavior of a sample from a commercial heat of this aluminum-chromium-molybdenum steel, together with pertinent supplementary data including the equilibrium transformation temperatures (Ae3 and Ae1), the temperature range of martensite formation, and the end-quench hardenability. These data are directly applicable to the heat-treatment of this type of steel and are of interest in revealing some of the fundamental effects of aluminum as an alloying element in steel. MATERIAL All specimens were prepared from a 13-in. diam bar forged from a 5 by 5-in. billet from a commercial heat made in an electric arc furnace. The composition of the bar was; C, 0.41 per cent: Mn, 0.57: P, 0.016: S, 0.005: Si, 0.24: Ni, 0.17: Cr, i.57: MO, 0.36: Al, 1.26. The forged bar was normalized from 1750°F (955°C) and then tempered for one hour at 1200°F (650°C), this tempering treatment having been given to facilitate the machining of specimens. EQUILIBRIUM TRANSFORMATION TEMPERATURES In hypoeutectoid steel the minimum temperature at which austenite is completely stable, Ae3, and the maximum temperature at which austenite is completely unstable, Ae1, are of great significance in heat-treatment. Since these temperatures are dependent upon com-

Jan 1, 1946

By Jay R. Burns

Two magnesium sand-casting alloys are commonly favored in the United States. These are referred to as H and C alloys (Dow Chemical Co.) or AM265 and AM260 alloys (American Magnesium Corporation). Both are of an aluminum-zinc-manganese type. H alloy contains 6 per cent aluminum and 3 per cent zinc and is characterized by relatively good toughness. C alloy contains g per cent aluminum and 2 per cent zinc and is employed where high yield strength and pressure tightness are required. Examination of magnesium castings poured in Europe and England,1,2 however, demonstrates that H and C alloys are replaced by A8 and AZ91, respectively. That is, A8 represents a magnesium alloy having superior toughness while AZ91 is suitable for high yield strength and pressure-tight applications. The basic difference between the American and European alloys is that the foreign alloys employ a somewhat higher aluminum content and less zinc than is found in H and C alloys. The mechanical properties of the alloys, when divided into high and low-aluminum groups, are quite similar, as determined from separately cast foundry-control type test bars.3 In this paper the decrease of mechanical properties caused by any given amount of microporosity is measured for H, C, A8, and AZ91 alloys. The relative susceptibility of each of the four alloys to microporosity is also determined. Typical mechanical properties and nominal chemical analyses are reported in Table I. [ ] The apparent similarities between the two alloys in each group have led to considerable discussion as to the relative merits of each of the compositions.2 Popular points for comparison between the alloys have been the relative susceptibility of each of the four alloys to microporosity5 and the effect of this microporosity on their mechanical properties. It is primarily intended, in this paper, to show the

Jan 1, 1946

By John T. Eash

During the course of the war the supply of tin in this country has steadily decreased and a continued effort has been made since the beginning of the emergency to use alloys that are either tin free or contain appreciably lower quantities of it. Even with the use of emergency materials, the tin supply has become particularly acute, and it is estimated that after recovery of the far eastern mines probably one to two years will be required before our normal annual supply is attained. One of the major tin-consuming fields is the bronze industry. Recommendations were made several years ago by the War Production Board toward the use of bronzes of lower tin content and manganese bronze and yellow brass for the customarily used tin-bronze alloys. The substitution of 88-5-5-2 copper-nickel-tin-zinc for composition G received considerable attention before the war, and consequently this alloy and modifications of it have been adopted for some current structural and pressure castings requiring high mechanical properties. Another of the commonly used bronzes is the 10 per cent tin 10 per cent lead copper alloy for heavy-duty bearings. It has been known for some time that about 2.5 per cent nickel could be substituted for an equal amount of tin with retention of equivalent casting and tensile properties; however, it was desirable that a still greater conservation of tin be made. Consequently the present paper deals with the development of an alloy of low tin content that could be used for bearings. Selection or Composition While the final criterion of the suitability of an alloy for a bearing must of course be determined by practical applications where all the ramifications of service conditions are encountered, certain short cuts in the initial selection of compositions are necessary to avoid an extensive and time-consuming investigation. The present program has been to match certain metallurgical properties of the 80-10-10 bronze that have been shown by previous investigations to be related to good bearing qualities. Such properties as microstruc-ture, hardness, compressive yield strength, ductility, and castability have been considered, and certain simple wear tests have been made. Of the readily assessed characteristics desired in a good bearing alloy, one can be certain that a uniform distribution of lead is required in a leaded bronze. It has generally been found that segregation of lead is one of the chief difficulties with this type of material. Tin has a powerful effect on lead distribution, and with 10 per cent present produces a random distribution of chunky particles, such as are shown in Fig' 1. I' In the tin bronze contains the hard alpha + delta

Jan 1, 1946

By George R. Elliott

Methods are presented for measuring and comparing "degree" of water drive, and for observing the control that rate of withdrawal exerts over decline of reservoir pressure. Degree of water drive is studied from pressure-production curves of 10 reservoirs; the method used to present these comparatively is to convert cumulative oil production from barrels to percentage of ultimate. Degree of water drive is also represented by a "water-encroachment factor," representing barrels of water influx per pound-month per acre-foot of oil reservoir. Pressure-production curves for the water-drive reservoirs after a period of declining pressure show a diminishing angle of slope, in some cases to the point where pressure ceases to decline or where it even increases; the shapes of these curves are in marked contrast to the dissolved-gas type of curve, which shows a general trend toward zero pressure at ultimate oil recovery. Yearly rate of oil production in percentage of ultimate oil recovery is correlated with pressure decline. The correct rate of production of oil with its associated gas and water sustains pressure in reservoirs having a high water-encroachment factor. For reservoirs having a low water-encroachment factor, it is necessary to inject the produced water and even inject large volumes of water from an outside source. The discussion of the actual reservoirs is preceded by a general review and is followed by a substantial bibliography. It is now generally accepted that water drive is capable of yielding 60 to 80 per cent of the original oil in place in most reservoirs, as compared with 20 to 40 per cent for dissolved-gas drive. There is no need to question the importance of controlling a reservoir in order to take advantage of such an efficient mechanism. What is a water-drive reservoir? Oil reservoirs usually combine two or more of the four basic mechanisms: dissolved-gas drive, gas-cap drive, water drive, gravity drainage. A water-drive reservoir is one in which water advances to take the place of the oil and gas produced. When the oil withdrawal rate is sufficiently low, the water will tend to maintain pressure. The maximum effectiveness is attained when the water follows the oil withdrawal so closely that little or no decline in pressure occurs. Oil in its underground reservoir is associated with water. This water is significant in the production of the oil according to the source of supply and the permeability of the surrounding formation. As oil is produced and the pressure is lowered, water can move in to replace the oil. With adequate supply and sufficient permeability, actual movement takes place on an extensive scale. The first movement of water takes place by expansion of the water and its associated fluids. While this expansion is of little importance in some fields, in others it is sufficient to supply all of the energy required for the production of oil. When a pressure differential has been established

Jan 1, 1946

By J. McLaren Forbes

Geologists and engineers in charge of diamond drilling often have no practical experience in the work, yet they must direct the drillers. In discussing some of the problems that arise, the author of this paper has tried to remember the things he did not know about diamond drilling when he first came in contact with that work. The basic reason for most diamond-drill holes is to obtain information. The more thorough the understanding of the geological and engineering problems involved, the greater will be the benefit derived from a drilling program. One of the best methods to ensure some thinking before drilling is to record on the permanent drill log, before the hole is collared, the reasons for the work and the information desired from that particular hole. When the hole is finished, the information obtained should be recorded. Driller The choice of a diamond driller is very important. If no experienced driller is available, a competent miner who has a sense of responsibility and better than average mechanical ingenuity can do the work. The best answer to most practical drilling problems, from the standpoint of the person in charge of the drilling program, is the service of experienced diamond drillers or drilling firms. Equipment Drilling equipment should be adequate to put down the longest hole desired and handle the toughest ground encountered. The type of bit used depends upon the ground drilled. Experimenting with various bits and careful study of footage records are the best means of determining which to use. Under ordinary circumstances it is best to drill using an EX barrel when possible. The length of rod and core barrels that can be used depends on the size of the drill station. Also, the length of core barrel depends on the way the ground cores. In good ground as much core will be recovered with a 10-ft. barrel as with a shorter one, and with considerable saving of drilling time. A water pump is needed if the hole is so deep that the water pressure is not strong enough to wash out the cuttings, or if it is drilled at an angle that prevents full force of the water pressure. Instructions For an Inexperienced Driller 1. Never run a bit too long a time. When a bit seems to be "good for one more run," discard it. 2. Always let the rods down on bottom easily. Protect the bit from sudden shock. 3. Start the drilling slowly and easily. Do not put pressure on the bit too fast. Diamonds can break. 4. Be sure the water pressure is strong enough to clear the bit, but do not use more water than is needed, as it may wash away the core. Usually, if no core is recovered the hole is a total loss. 5. When dry-blocking, do not run without water longer than necessary as the bit may burn. 6. Be sure the rods are well caulked and tightly screwed together. If not well caulked they will lose water, and if not

Jan 1, 1946

By Donald D. Smythe

Tars paper describes briefly the topography and geology of the region where the mica-bearing pegmatites are found and discusses prospecting, the quality of the mica, its preparation, and evaluation of the deposits. Muscovite mica occurs in a number of widely separated localities in Brazil, but production has come largely from deposits in the southeastern and eastern part of the State of Minas Gerais (Fig. I). There the deposits form a discontinuous zone, which starts at a point 90 km. north of the city of Rio de Janeiro and extends north for some 500 km., roughly parallel to the coast. A maximum width of 180 km. is reached along the Rio Doce. To the west in Minas Gerais, and extending east into the states of Espirito Santo and Rio de Janeiro, the mica zone proper is fringed by areas in which there are scattered occurrences of mica-bearing pegmatites. A few of these outlying deposits have produced commercial mica, but most of them are unimportant. To the southwest, in the State of São Paulo, there are a number of mines, which at one time produced a very considerable amount of sheet mica, largely as a by-product of kaolin mining. These deposits, and, a few others lying between them and the main productive areas to the northeast, appear to be the southwestern continuation of the strong Minas Gerais mica zone. In the vicinity of Conquista, just north of the Minas Gerais boundary in the State of Bahia, and still farther north, near Jacobina, there are several known mica deposits. Their location indicates that they may be the northern continuation of the main mica zone. The major part of Brazilian mica production has come from four areas within the mica zone proper; from north to south, Governador Valadares, Raul Soares, Espera Feliz, and Muriaé. The first is 190 km. from north to south and reaches a maximum width of 180 km. The Raul Soares area extends 135 km. from northeast to southwest, and in places is 80 km. wide. The Espera Feliz area is 100 km. from north to south, and reaches a width of 35 km. The Muriaé area extends 150 km. from northeast to southwest and its width reaches 40 kilometers. Between the known productive areas, and in the areas directly to the southwest and to the north of them, little mica has been produced. These gaps, as well as certain irregularities in the outline of the mica zone itself, are to be ascribed either to lack of prospecting or to conditions preventing the discovery of mica, rather than to its nonexistence. Elsewhere in Brazil mica has been reported from eastern Goiaz, Ceará, Pernambuco, Rio Grande do Sul, Matto

Jan 1, 1946

By G. L. Kothny

DEVELOPMENTS of well-surveying instruments, coring and core orientation, were in an advanced state when drilling for oil began-these developments actually originated with the mining industry.1 Surveying of oil wells was not generally used in the United States until Alexander Anderson2 disclosed that the majority of wells drilled with rotary tools were crooked, with average horizontal drifts of about 516 ft. for holes 5000 ft. deep and about 793 ft. for holes 6000 ft. deep. This disclosure brought about the development of many additional instruments for surveying oil wells during the progress of drilling and after their completion. Surveying of boreholes, during the process of drilling at regular depth intervals, became a standard practice in the petroleum industry. Some producing states even established laws making check surveys mandatory, during drilling and under certain conditions also after completion. The surveying of boreholes also brought about changes and improvements in drilling practices. It provides information for the guidance of the hole while drilling, and for plotting the course as the work progresses, enabling the driller to take corrective measures immediately and with the least expense. The reasons for drilling straight holes are too well recognized to warrant any full discussion of them here. Straight holes are less costly to drill, because [ ] they reach the object on the shortest course. Table I shows the horizontal drift and loss in vertical depth for various angles of inclination. It is not surprising, therefore that many drilling contracts for oil wells today limit the drilling contractor to a maximum inclination off the vertical of 2° or 3°. In the mining industry the reasons for drilling straight holes are still more serious. A crooked hole may miss an ore body underground or provide incorrect information regarding an ore body. TYPES OF SURVEYING INSTRUMENTS The surveying instruments used in oil-well drilling may be classed in two types: I. Inclinometers, recording inclination only.

Jan 1, 1946

By R. R. Dickson

Princess colliery, the largest mine operated by the Old Sydney Collieries, Limited, commenced operations in 1877. It was the first mine sunk in the Sydney coal field with the primary object of working submarine coal. Until 1925, coal was won by the room-and-pillar system. By that year, the depth of cover over the workings was 1,300 feet, and physical conditions had become such that it was impossible to extract completely the pillars formed by the working of the rooms. Because of this, the system of work was changed to longwall in the early part of that year. At first, an orthodox hand-pick method was used, with gate roads laid off at 50-foot centres and the mine cars loaded by hand directly on the longwall faces. Later in the year, the first machine-cut conveyor longwall faces were started.

Jan 1, 1946

By W. C. Knoblaugh

ROTARY kilns are adaptable to many fuels, but this paper deals principally with the use of powdered coal. The observations and conclusions presented are based on rotary kilns used in the manufacture of basic refractories for steel furnaces. Solid fuels are pulverized for two principal reasons: (I) ease of control, and (2) rapidity of combustion. By the use of pulverized coal, the operator can increase or decrease the fuel supply by small increments and with very little time lag between the change of control and the resultant change in the flame. This is extremely important in this type of furnace, as the temperature range for maturing the clinker is very narrow. By fine grinding, it is possible to increase the rate of burning of the coal, thereby liberating great quantities of heat within a small space in a short time. Under given conditions, temperature is a measure of the heat liberated per unit of time. To attain the temperatures of 2950° to 3150°F., which are encountered in the manufacture of various steel-furnace refractories, it is estimated that it is necessary to liberate 125,000 to I75,000 B.t.u. per cubic foot of the burning zone per hour. The manufacture of dolomitic refractories is a ceramic process and, as is true in most such processes, the material must be subjected to a certain critical temperature for a certain length of time in order to complete the reaction. If the time of reaction is reduced, the temperature must be increased; in other words, if the rate at which the material flows through the hot zone of the kiln is increased, the temperature of the hot zone must be increased to compensate for this shorter exposure to the flame. FIRING WITH PULVERIZED COAL Fig. I is a line drawing of a rotary kiln with the attendant equipment indicated in their relative positions. The kiln proper consists of a sloping, refractory-lined steel tube rotating slowly about its longitudinal axis (0.75 r.p.m.), and is countercurrent in operation in that the raw feed is introduced at the stack end and gradually approaches the zone of highest temperature at the lower end, where the fuel is introduced. Before 1930, the usual method of firing a rotary kiln was to store the coal in the pulverized form and then feed from this storage to the kiln as needed. This proved unsatisfactory and dangerous because of dust explosions and the inability to obtain an even feed to the kiln caused by arching of the coal in storage and flooding of the coal feeders. In later years the practice has been to store the raw coal and grind it as it is needed. Such a layout is indicated in Fig. I. The coal is stored in bins, charged from the top and drawn from the bottom into recording scales and then into some type of unit pulverizer. There are a number of good pulverizers on the market, each incorporating features that the manufacturer considers outstanding.

Jan 1, 1946

By R. G. O’Meara, M. M. Fine

ONE of the principal activities of the Bureau of Mines connected with the recent war was to help to increase the supply of strategic and critical minerals. Fluorite was one of the most critical of the nonmetallic minerals because of the increased demand for it as a flux in basic open-hearth and electric steel furnaces and as a raw material for the production of artificial cryolite used in the aluminum industry. Wartime developments in the technology of hydrofluoric acid, such as the use of the anhydrous acid as a catalyst in production of high-octane gasoline and the use of organic fluorides as carriers for insecticides, also increased the demand for acid-grade fluorite.[t] In 1943 the consumption of acid-grade fluorite was advancing at a more rapid rate than production, and was only slightly less than production during the latter half of the year.1 The outlook for the postwar market for fluorite is encouraging. Steel production is expected to remain high until the domestic demand for commodities not manufactured during the war is satisfied. The uses for hydrofluoric acid are expected to increase under the impetus of war-initiated research. In consideration of these and other factors some authorities predict a postwar demand for fluorite equal to about 60 to 75 per cent of the wartime production.1,2 Others believe that the postwar fluorite industry will be permanently expanded over its prewar status.3 ACKNOWLEDGMENT This paper is one of many reporting on various aspects of the Bureau of Mines program directed toward the more effective utilization of our mineral resources. The program has been under the general supervision of R. S. Dean, Assistant Director, since July 1942. The scope of the paper falls in the province of the Metallurgical Branch, whose activities embrace the separation of difficultly beneficiated ores, the production of pure metals from domestic deposits, the exploitation of marginal ore reserves, the recovery of secondary metals, and the improvement of present industrial metallurgical practice. The investigation was initiated at the request of Mr. J. H. Steinmesch, vice-president and general manager, Minerva Oil Co., Eldorado, Ill. His hearty cooperation and helpful suggestions, and those of Mr. O. E. Anderson, mill superintendent,

Jan 1, 1946