Search Documents

By Geo. H. Ashley

The following paper is intended to be suggestive only, and to open the way for discussion and further observation. Its preparation was requested only two days before the time limit set for the submission of the papers comprising this symposium. Thus no time existed for detailed studies, so it is largely a memorandum of such facts as have come incidentally to the notice of the writer in the study of coal in the field. The field study of sulfur in coal has received very little special attention or description from coal student's. The presence of sulfur concretions is noted in hundreds of descriptions, and certain benches of a coal bed may be described as "sulfury" or the presence and position of sulfur bands may be noted in coal sections in connection with sampling. It may be accepted that some sulfur is present in all coal. The amount varies greatly in different regions, in different beds, and in the same bed in different areas. The anthracite of Rhode Island comes the nearest of any coal known to the writer of being free from sulfur, several analyses of that coal showing less than 0.1 per cent. Subbitumi-nous coals in Colorado in a few places have close to 0.2 per cent. of sulfur on the dry-coal basis and in other states subbituminous coals approach this lower limit. Bituminous coals seldom run under 0.4 per cent. of sulfur on the dry basis, though in a few places dry bituminous coals in Colorado and Washington have between 0.3 and 0.4 per cent. The better known bituminous coals have almost everywhere over 0.4 per cent. The best of the Pocahontas and New River coals run close to 0.4 per cent., but there is very little commercial coal in Pennsylvania, Ohio, Indiana, Illinois, Kentucky, or the other states, that runs under 0.5 per cent. on the dry basis. From these minimum figures, the amount will range up to 5 or 6 per cent. or higher if visible sulfur is not excluded. It must be remembered that the usual analysis of a coal bed is not intended to give the total proportion of sulfur in the bed but the amount in the coal after the removal of the more obvious and larger sulfur masses. Professor Parr has already pointed out that, chemically, sulfur occurs in several forms: as pyrite, organic sulfur, sulfates, and possibly as un-combined sulfur. Sulfur in the form of sulfates is commonly the obvious result of the weathering of pyrite and may be found in the coal within .

Jan 1, 1920

By George Smith

TWELVE years ago, the Director of the United States Geological Survey addressed to the Secretary of the Interior a letter calling attention to the government's need for liquid fuel for naval use and pointing out that the rate of increase in demand was more rapid than the increase in production.1 This letter, in a way, inaugurated the policy of public oil-land withdrawals, which was well founded in its primary purpose of protecting the oil industry and highly desirable in its immediate effect of checking the over-development of that day in California. Unfortunately, however, through delays in legislation, this policy may be regarded now as having outlived both its intent and its usefulness. In 1908, the country's production of oil was 178,500,000 bbl., and there was a surplus above consumption of more than 20,000,000 bbl. available to go into storage.: In 1918, 10 years later, the oil wells of the United States yielded 356,000,000 bbl.-nearly twice the yield of 1908-but to meet the demands of the increased consumption more than 24,000,000 bbl. had to be drawn from storage. Nor is this all of the brief comparison. In 1918, our excess of imports over exports of crude petroleum was nearly 33,000,000 bbl. whereas in 1908 we exported 3,500,000 bbl., which was net, as we had not begun to import Mexican oil. In this period, the annual fuel-oil consumption of the railroads alone has increased from 16,871,000 to 36,714,000. bbl.; the annual gasoline production from 540,000,000 gal. to 3,500,000,000 gal. This record may be taken not only as justifying the earlier appeal for Federal action, but as warranting deliberate attention to the oil problem of today.

Jan 1, 1920

By Raymond M. Howe

Additional data have been secured on the disintegration of furnace linings and the spalling of stove brick. The first article on the disintegration of furnace linings appears to have been written by John Pattinson in 1876.l The furnace involved was 85 ft. (25.0 m.) higher and 27 ft. (8.2 m.) in diameter at the boshes; after being in blast five years, the top brick became contaminated with carbon and disintegrated. An examination of the lining showed that the discolored, disintegrated brick were in a zone found from 35 to 67 ft. (10.6 to 20.4 m.) above the hearth; immediately below, in a zone extending from 22 to 40 ft. (6.7 to 12.1 m.) above the hearth, the brick were hard and porcelain-like in appearance. Analyses of samples taken from the different sections are given in Table I. The water-soluble portion found in the sample taken 39 ft. (11.8 m.) above the hearth had a composition approximately as follows: silica, 0.50 per cent.; lime, 0.04 per cent.; potash, 0.78 per cent.; soda, 0.20 per cent.; potassium chloride, 6.19 per cent.; moisture, 1.03 per cent.; total, 8.74 per cent. The carbon Table 1.—-Analyses of Samples Taken from Diferent Sections of Furnace . I ii In Iv v Section 67 Section 45 Seotion 39 Section of Original ft Above ft above ft above vitrified Lining Hearth Hearth Hearth Portion Per Cent. per Cent per Cent per cent. per Cent Silica........................... 55.70 55.60 55.67 47.60 37.07, Alumina........................ 35.50 35.40 30.00 26.47 23.18 Ferric oxide..................... 3.00 1.32 0.96 Lime........................... 0.23 0.06 0.17 Magnesia....................... 1.22 0.95 0.86 0.00 Potash......................... 2.60 2.10 5.30 7.54 21.59 Soda.........,.................. 0.45 0.42 1.67 0-76 6.28 Ca1bon ......................... 2.05 3.24 5.97 Carbon dioxide.................................. 2.. 17 Water...................................... 7.70 Water-soluble........................... 8.74

Jan 1, 1920

By E. A. Holbrook

Research, primarily, is finding out the truth. Research applied to enigeering opens the door to new principies and processes, the application of which benefits mankind in a material way. The engineer believes that investigation instituted with the primary view of making the results directly applicable to the industries is the highest type of research. Coal is essentially the basis of modern industrial civilization; therefore, any considerable research pertaining to coal must link itself to the industry by practical application of the results of the research. In other words, all investigational work connected in any way with coal leads to conclusions that permit a better understanding of the origin, nature of occurrence, composition, better and safer mining, more careful preparation, or greater efficiency in utilization of coal. Modern engineering research has been fostered essentially by universities and in the laboratories of institutions of learning. Coal problems that lend themselves to solution in the laboratories have been first attacked and are perhaps the farthest toward solution. For example, a great amount of research work has been carried out with the various phases of chemistry connected with coal. On the other hand, the equally important problems connected with methods of mining have received but little attention, primarily because their solution involves the continued use of a great and expensive laboratory, which is none other than the mine itself. As many of the problems already solved have had chemistry as their background, so many of the problems unsolved have physics as their background; there are also unsolved problems that deal in coal economics. Even psychology must be called upon in future coal-mining research as a basis for solving those great problems that deal with human relationships. 'In general, considerable advance has been made in coal research dealing with chemistry, not so much progress has been made with problems having physics and engineering as a background, while there is a tremendous range of untouched problems that deal essentially with business and psychology. Research in coal mining is not a new development. In the chronicles of the northern coal trade as published in the Transactions of the North

Jan 1, 1920

By W. L. DeMoulin

A rather detailed description of the entire plant and leaching process was given in a paper recently presented to the Institute,I so this paper will cover briefly only the crushing practice of the New Cornelia Copper Co. for the year 1918. The ore, which is mined by steam shovels and loaded in side-dump cars, passes through two crushing plants. These crushing plants were constructed to crush the ore required by a leaching plant of 5000 tons daily capacity, during a crushing period of 16 hours. The primary plant reduces to less than 3 in. (76 mm.) and the secondary plant, to 1/4 in. (6.35 mm.), which is sufficiently fine for satisfactory percolation of solution through the ore in the leaching tanks, and to give-good extraction. The ore is then conveyed to the leaching tanks by a system of 28-in. (71-cm.) belt conveyors. On the way to the leaching tanks, it passes through an automatic sampling plant, where a 1-per cent. sample is taken. From the primary crushing plant, the ore is conveyed by two 36-in. (91-cm.) belt conveyors to a 10,000-ton steel storage bin, with a reinforced-concrete flat bottom. The ore discharges from the bottom of this' bin onto four 20-in. belt conveyors, which deliver it to the four units of crushers in the secondary crushing plant. There is no storage bin between the mine and the primary crushing plant. The ore breaks very coarse, is very hard, and contains a great many boulders, some as large as 4 1/2 by 4 1/2 by 10 ft. (1.3 by 1.3 by 3 m.). Jams form in the bowl of the coarse crusher in the primary crushing plant, as a consequence, and are freed by means of an immense steel hook operated from a 40-ton electric traveling crane. Primary Crushing Plant The primary plant consists of one No. 24 Gates, style K, gyratory crusher, followed by four Gates No. 8, style K, gyratory crushers. All

Jan 1, 1920

By H. G. Moulton

The increasing scale of mining operations over the past decade, particularly in connection with the exploitation of large bodies of comparatively low-grade copper ores, has made necessary the study of the behavior of rock under failure. When extractions of as high as 40,000 tons a day are reached in steam-shovel operations and as high as 20,000 tons per day in underground mining operations, it is evident that excavations soon become of such size that the behavior of the rock will often be dependent on fundamental principles applicable to more or less homogeneous materials under stress, rather than on weathering or local planes of weakness. In the ordinary rock excavations encountered in civil-engineering practice, such as excavations for subways, highways, railroads, etc., rock faces are not carried to depths sufficient to develop any pressures, or consequently any failures, except those due to loose masses resulting from local planes of weakness. When, however, orebodies whose tonnage is measured by hundreds of thousands are to be extracted by steam-shovel operations in open pits, it is necessary to determine if possible in advance the slopes that the sides of the pits will assume, for these slopes influence the shape of the excavations and thereby the amount of ore that may be extracted by the open-pit method. When large orebodies are mined underground at depths of 300 to 500 ft. (91 to 152 m.) by caving methods, the surface subsiding as the ore is withdrawn, it is necessary to determine in advance the outermost limits of fracture in the subsiding surface, for on the delineation of these limits depends the location of surface improvements, mills, smelters, etc. and also the location of development work, such as hoisting shafts, main haulage levels, and all other underground openings that must remain undisturbed during the period of ore extraction. Heretofore, in civil-engineering practice, it has been assumed that earth and rock behave differently in failure. For the calculation of earth pressures, formulas are used in which the assumption is made that earth banks fail by sliding along the slope determined by the frictional resistance of the material. The line of failure and the resulting pressure is held to be dependent on the angle of repose, which is different for varying

Jan 1, 1920

Jan 1, 1920

By Howard S. Lee

In central Colorado is a great belt of intrusive porphyry nearly 100 miles long (160 km.), extending from the Clear Creek district on the north to Aspen on the south, which includes many of the well known mining camps of the state. Near the southern end of this belt, at Leadville, the occurrence of these intrusives is most marked, resulting in intensive mineralization and the formation of a great variety of large orebodies. During the past 40 years, Leadville has been a steady producer of gold, silver, lead, zinc, manganese, iron, and bismuth, in the forms of sulfide, carbonate and oxide ores. It is the purpose of this paper to discuss pyrite alone, which, under present economic conditions, is valuable chiefly for its sulfur contents. The ore-bearing formation of the Leadville district consists of two beds of limestone separated by a layer of quartzite. The upper limeatone is carbonaceous, and is known locally as the blue limestone. It varies in thickness from 50 to 300 ft. (15 to 91 m.). The lower limestone is Silurian, known locally as white limestone, and is about the same thickness as the upper bed. Underneath the Silurian limestone is a layer of Cambrian quartzite from 100 to 250 ft. (30 to 76 m.) thick resting on Archean granite, which forms the limit of ore deposition. As a rule, there is a sheet of white porphyry above the upper, or blue limestone; a sheet of gray porphyry is associated with the blue limestone, either in or below it, but the porphyries are not so regular as the quartzites and limestones and are not always found in their expected positions. Throughout the district there is an elaborate system of faults and intrusive porphyry dikes, which have an important bearing on ore deposits. The writer has seen two or three orebodies which were not closely associated with either a fault or a porphyry dike, but if the minor fractures and water courses are considered as part of the fault system it is safe to say that all orebodies are directly traceable to one or both of these causes. The distribution of pyrite in the Leadville district is quite general; but, eliminating the smaller bodies and those containing prohibitive quantities of zinc or lead, and considering only the larger deposits commercially valuable for their sulfur, we find the chief pyritic ore-bodies extending in a zone approximately 6000 ft. (1828 m.) long and several hundred feet wide, from the Yak and Moyer, on the south; through the Louisville, Greenback, Mahala, Adams, and Wolftone, on Carbonate Hill; across Yankee Hill, and into the Quadrilateral, Denver City, and Tip Top, on Fryer Hill.

Jan 1, 1920

By G. F. Comstock

The subject of transverse fissures in steel rails has been discussed very thoroughly in recent years from various points of view and the final opinions expressed may be roughly classified into two groups: That these fissures are the result merely of fatigue of the steel and are independent of the quality of the metal. That the quality of the metal and the mill practice must have something to do with them. The first point of view was most ably and logically presented by J. E. Howard,' and in the discussion of this paper, as well as in several other preceding publications, Dr. P. H. Dudley, Consulting Engineer of the New York Central Lines, has strongly defended the other opinion.2 The steel makers of the country have naturally rallied under Mr. Howard's banner, hoping to place the entire blame for these failures upon the railroads with their high wheel-loads, hard steel, heavy traffic, and sometimes inferior road-bed; while the railroad men, on the other hand, have been busy accumulating statistics and records in the effort to find an actual reason in the rails themselves that would account for the seemingly haphazard occurrence of transverse fissures under varying conditions and at widely separated points. The view that these fissures were due merely to normal fatigue under alternating stresses seemed most reasonable to the writer until quite recently, because from work done in this laboratory, as well as the work of other investigators, of the problem, no structural differences, in the vast majority of cases, were found between metal at the nuclei of transverse fissures and metal at similar positions in the same rails or in other rails that had not developed fissures. Within the last year or two, however, since the method of etching polished sections for the microscope with a oupric chloride solution has been tried systematically on lengthwise sections, passing through the nuclei of transverse fissures, evidence

Jan 1, 1920

By Paul D. Merica, L. J. Gurevich

In connection with other investigations on the properties and characteristics of chilled-iron car wheels, the question as to the best range of annealing temperatures was raised. Chilled-iron wheels are cast with a chill against the tread and the inside of the flange, the remainder being in sand. The composition of the metal is so chosen that under these conditions the trcad and inside of the flange will show white iron to a depth of from 5/8 to in. (15 to 22 mm.), the remainder of the wheel becoming graph itized or gray. In order to relieve the stresses set up during cooling under such drastic conditions, the wheels are stripped from the mold, while still red hot, piled in a soaking pit, and allowed to cool very slowly from their temperature at stripping. Obviously the most suitable temperature for this annealing is the highest at which no formation of graphite occurs within the white tread and at which the wheels can be stripped from the molds. Inasmuch as no direct determinations have been made of the temperatures at which the formation of graphite takes place in white iron of compositions used in car wheels upon annealing, it was considered worth while to determine these temperatures as a means of establishing the maximum temperatures at which the annealing of the wheels may be carried out. In the course of this work, some incidental observations were made which are of interest in connection with the theory of graphitization in whitc iron. The literature on the subject of the formation of graphite both during cooling at casting and upon annealing is very extensive and can be best studied by reference to a comprehensive discussion of the subject by Hatfie1d.l Perhaps the most important contributions of previous investigation are the following: 1. Whether a given mass of molten iron becomes white, mottled, or gay upon casting, depends on its composition and its rate of cooling through the temperature range of solidification and immediately below. 2. The more rapid the rate of cooling, the less is the extent of graphitization.

Jan 1, 1920

By F. E. Wormser

"Arsenic has been recently quoted at 10 1/2 - 11 cents per pound, an increase over the prevailing price of last fall, when arsenic was cents, as against pre-war prices around 4 cents is evidently a sustained demand for this material. The following statements are intended to summarize briefly some particulars regarding arsenic.Commercial arsenic is the white arsenious oxide (As203). This is the form in which it is generally marketed, as the uses of arsenic demand its industrial application in this form. Arsenic as an element finds rather restricted use in the hardening of lead shot, ere it is to some extent replacing the use of antimony, while white arsenic is employed in a variety of manufacturing processes, chief of which is the manufacture of insecticides and sprays. The poisonous nature of most arsenic compounds, the commonly known ones being paris green and lead arsenate, and its relative cheapness, make arsenic a material suitable for this purpose. The stimulation of agriculture during the war greatly increased the demand for arsenical insecticide. Glass making consumes a large amount of arsenic as it has been impart increased brilliancy to the glass. Crude commercial arsenic is often used to kill weeds along railroad tracks. Arsenious oxide is used also for preserving hides, while the disulphide, AS2S2), finds an application in dehairing hides for the finest grade leather, as it least affects the product. Orpiment (As233), is used in textile dyeing. Wall paints and wall paper formerly consumed considerable arsenic in the form of paris green, but this use has been largely,given up due to the poisonous nature of the dust from the product. Sodium arsenate for a similar reason, is now little used in printing where it had found application. The great objection to arsenical yes and paints is the risk of poisoning from use of the manufactured article. Sodium arsenite is the principal poisonous in¬gredient of many cattle and sheep dips. Arsenic compounds are also used medicinally."

Jan 1, 1920

By Luther W. Lennox

The purpose of this article is not to compare one type of grinding machinery with another and to conclude from a series of tests that one particular machine is superior to all others. Neither is the reader asked to tire himself with the details of many tests to prove the statements herein made. The Chilean mill stands today almost an outcast from the milling world. It ranks with the applicant for a job who has been given a trial along with others and condemned because he was not able to perform the definite task assigned as well as the others, and was forever eliminated. The judges did not tarry long enough to try this aspirant in a field of a slightly different nature. Even though it has been condemned, the writer contends that the published records will indicate that the trials were never shifted into the field of greatest efficiency for the . Chilean mill. Those of us who cling to this outcast as a fine grinder in our milling operations do not wish, naturally, to be condemned also, with the machine, and yet we feel that we are classed as behind the times, at least in this phase of our milling judgment. Hence there is considerable personal feeling in our efforts. During the last few years there have been published several papers on the relative merits of the various grinding machines. In two of these articles a comparison was made between Chilean mills and cylindrical grinders. In each case the Chilean mill came out second best from about all standpoints. The outstanding feature in these comparisons would seem to be the decided attempt to keep all conditions the same, so that each machine could be judged on its merit. As Mr. David Cole states,1 "We are inclined to regard a direct comparison of grinders arranged side by side, and making a product that affords as nearly as possible the same screen measure, as the Supreme Court in these grinding matters." The writer agrees that this is the very best method for true comparison between machines. The results in the two detailed tests should give the relative merits of the two grinders in doing the work assigned. And they probably do. The conclusion drawn in each case was adverse to the Chilean mill as a fine-grinding machine. However, the duty placed upon the machines was that of converting material that had already been

Jan 1, 1920

By O. U. Bradley

The methods of handling the oil output of the Mid-Continent fields are not unlike those practised in other oil fields of the United States, and it is not expected that this paper will present any entirely novel ideas. Some features of the practice of handling this oil may be of interest, however. Wooden Gaging Tanks Practically all of the oil sold to pipe line? and other purchasing agencies throughout the Mid-Continent field is gaged from wooden tanks. Steel gaging tanks are slowly coming into use, and are preferable in many ways—leakage and evaporation are reduced, and the strapping and recalculation of capacities are unnecessary. The wooden tanks are slightly coned to facilitate tightening the hoops. The sizes in common use are 250, 500, 800 and 1600 bbl. The number and the capacity of the gaging tanks upon any producing oil property depend upon its production, and the facilities for disposing of the output. The 1600-bbl. size was the most common in the Cushing field, particularly during the period of flush production. The tanks are distributed over the leased premises in groups of two, three, and four tanks each, and these are filled from flow tanks, or through direct pipe connections with the heads of the wells. Flow tanks are merely temporary reservoirs to facilitate the transfer of oil from the wells to the gaging tanks. They diminish fire risk, and are considered indispensable on small producing properties where water is pumped with the oil, as they permit the refuse and water to 'settle out before the production is run to the gaging tanks. strapping and Calculations After a gaging tank has been strapped (measured) and its contents computed, a deduction of 3 per cent. is made from its computed volume. The strapping of a tank requires four steps: (1) The outer circumferences

Jan 1, 1920

Jan 1, 1920

By R. S. Archer

In the microscopic examination of aircraft-engine parts made of heat-treated alloy steels, the writer has been forcibly impressed by the failure of the usual etching processes to disclose any but gross defects in heat treatment. It seemed particularly desirable to bring out the grain size of the steel, which is indicated in the ordinary etching processes chiefly by the change in orientation of structure from grain to grain. After various attempts, a fairly successful method has been found, which is here presented in the hope that it may be of use to those who have occasion to examine these steels in the hcat-treated condition. The specimens worked with have been mostly chrome-nickel steels heat treated (that is, hardened and tempered) to a Brinell hardness of around 300. A few experiments with other specimens will be referred to later. Briefly, the method employed consists in etching the steel about 10 min. in a fresh solution of picric acid in ethyl alcohol, and then rubbing off the smudge of carbonaceous matter on moist broadcloth. Different samples of almost identical analysis, heat treatment, and physical properties (including resistance to impact) respond quite differently to this treatment. In some, the grain boundaries are developed quite readily, while in others, especially in those whose grain is unusually fine or in which the final hardening heat has not quite obliterated the previous crystallization, the results are more obscure. The exact time of etching to secure the best results also differs for various samples, and the greatest success is usually attained by a process of "tinkering." Such a process is illustrated in a series of micrographs, the first six of which were taken at a magnification of 300 diameters. The properties of the steel are as follows: Carbon, per cent............... 0.42 Brinell hardness.............. 293 Nickel, per cent................ 1.35 Yield point, pounds per square Chromium, per cent............. 0.90 inch........................ 131,000 Copper, per cent................ 0.025 Maximum strength, pounds per Manganese, per cent............ 0.74 square inch................. 144,500 Phosphorus, per cent............ 0.024 Elongation in 1 in., per cent... 28 Sulfur, per cent................ 0.036 Lod impact, foot-pounds...... 51 Reduction of area, per cent...... 57.3

Jan 1, 1920

Jan 1, 1920

By Roswell Johnson

ALL strata not yielding oil or gas in commercial quantities or a corresponding amount of water may be called dry in a wide sense. In petroleum geology,, however, we may exclude all sands of too low or fin porosity to yield gaseous or fluid contents to the hole drilled in the sand before any original pressure that its contents may be under is disturbed. Most rocks are of this class and they are not reservoirs in our definition; their "dryness" is wholly a matter of course. What are the contents of the pores or what is the exact porosity of such rocks is of almost no concern to us, for economically they are "dry." What does interest us is the content of a rock having sufficient porosity and the pores of sufficient size to yield oil or gas in commercial quantities, if they were present under original pressure: Dryness of these reservoirs is a matter of supreme practical importance. Three views current as to such dryness seem, to me, to apply in a few cases only. It is the purpose of this paper to give reasons for this position and for believing that, in ordinary sedimentary rocks, there is only rarely a reservoir of competent porosity and undisturbed pressure that is dry in the sense of not yielding water, oil, or gas when first penetrated. 1. Gardner1 writes of some Kentucky sands, "There has never been present any salt water or other water in the sand." Absence of water cannot demonstrate this position. It is necessary to show that the rocks were not laid down in water, but in air, and that they became so enclosed, while still above the water-table of the, ground water, that water has not been able to enter since. Most of these sands, and certainly the productive limestones, were deposited in water; and such sands as have been commercially productive show no reason for believing that the overlying shale or limestone was not laid down progressively from one direction and in water that would have flooded it. No adequate explanation has been offered for this hypothesis, which is so inherently improbable.

Jan 1, 1920

The sudden and untimely death of Dr. Charles R. Van Hise, late' president of the University of Wisconsin, was one of the greatest losses, not only to the educational world and science of geology, for which he was a great leader and pathfinder, but also to the world of mining and allied interests, for which he was an adviser and helper who blazed trails and pointed out paths of development, which the practical men of englneering and industry will follow long after his death. To the general public, Dr. Van Hise stood as a great educator who conceived and wrought out a new idea in the people's university .of .a commonwealth and as a great active mind that could not be held within the bounds of education and science but, by its own bigness and broadness, was forced into the contemplation of the larger affairs of the nation. To the engineering profession, dr. Van Hise will be remembered as a tireless worker who solved some of the most complex problems in geolpgy and the development of mineral resources and recorded these findings In a form that is of lasting value to those who follow him in similar labor. In this combination of thinker and worker, educator and economic student, scientist and practical engineer, lies Dr. Van Hise's contribution to his generation. As an educator, Dr. Van Hise attained perhaps his widest recognition, for in the University of which he was president he evolved and accomplished a new idea, which caused it to be called, in 1908, by President Eliot of Harvard, "the leading State University." At the time of his death, Nov. 19, 1918, he was just completing fourteen years as president and forty-three years as student and teacher in the University. His entire life of 61 years had been devoted to his State and its University. He was the first alumnus of the University and the first Wisconsin-born citizen to become its president—and he enjoyed the longest term as president of the institution. Since his graduation from its College of Engineering in 1879, he had been constantly a member of its faculty. As Chief Justice John B. Winslow, of the Wisconsin Supreme Court said at the time of President Van Hise's death, " Wisconsin has had many able sons, men who have served their Country and their State with ais-tinguished honor in various fields of effort, but among them all none, I believe, has rendered greater service in his time than President Van Hise. The University will be his true monument, for to him, more than to any one person, we owe the present commanding position of that, great Institution." What his "new ideal of a State University" was maybe best expressed in the words which he used to outline it in his inaugural address in 1904. "I shall never be content until the beneficent influence of the University of Wisconsin reaches every family of the State. This is my ideal of a State University. When the University of Wisconsin attains this ideal, it will be the first perfect State University.... The University of Wisconsin desires to prevent that greatest of all economic losses to the State, the loss of talent. To prevent this loss of talent, the University must not only provide for those who come to Madison for instruction, but must go out to the people of the State with the knowledge which they desire and need." Hence it was said early in his administration that "the boundaries of the State are the campus fence."

Jan 1, 1920

By E. V. Daveler

The milling plant of the Alaska-Gastineau Mining Co. is located at the town of Thane, Alaska, on Gastineau Channel, 4 mi. south of Juneau and directly across the channel from the Ready Bullion mine of the Treadwell mines on Douglas Island. Previous to the organization of the Alaska-Gastineau Mining Co., in 1912, the milling was done at the stamp mill of the Alaska Perseverance Co. located at the mine in Silver Bow Basin. But the contemplated increase in production made it necessary to locate the mill on Gastineau Channel, as not enough water was available at the mine during the winter months, nor was there room for taking care of the large tonnage of tailings that would ultimately be discarded from the mill. Character of Ore The gold and silver values occur in quartz lenses associated with pyrrhotite, galena, arsenical pyrites, and zinc blende. These lenses occur in large bodies of slate, schist, and metagabbro, which also carry some valuable metallic contents. With the essential low cost of mining, it was necessary to mine large bodies of low-grade material containing the high-grade streaks. Of the minerals, pyrrhotite, the magnetic sulfide of iron, is predominant, and galena is the next sulfide present in quantity. The gold occurs free and coarse and associated with the iron sulfide in its finer state. The silver occurs with the lead or is alloyed with the gold. A chemical analysis of the ore shows Silver............ 0.10 oz. Magnesia......... 0.4 per cent. Silica............. 59.7percent. Sulfur............ 1.2 per cent. Iron.............. 5.2 per cent. Lead............. 0.1 per cent. Alumina.......... 21.4percent. Zinc............. 0.2percent.. Lime............. 5.0 per cent. Experimental Work Investigations at the old Perseverance stamp mill had developed the following points: Roughing concentration following stamping gives a fair recovery.

Jan 1, 1920

Samuel T. Wellman, Cleveland pioneer steel man, who was often referred to as the "father of the open-hearth process of the United States," died suddenly on July 11, 1919, of heart disease, at Stratton, Me. For more than half a century, he was closely identified with the improvement of equipment used in the making of steel and contributed a number of inventions that virtually revolutionized the industry. Mr. Wellman was born Feb. 5, 1847, at Wareham, Mass., his father at the time being superintendent of the Nashua Iron Co., Nashua, N. H. After attending public school and a year at Norwich University, he served in the Civil War as a corporal of the first New Hampshire Heavy Artillery. He went to Pittsburgh in 1867 and assisted in starting the first crucible steel melting furnace built in America at the works of Anderson, Cook & Co. It melted a ton of steel with an average of 1000 Ib. of nut coal, which cost less than $1, while the melting of a ton of steel in crucibles in the old fashioned coke furnace took three tons of the very best coke, costing from $2 to $3 per ton. This furnace was a great success and in a very few years had driven the coke furnace out of use. From Anderson, Cook & Co., Mr. Wellman went to the Singer, Nimick & Co. works, Pittsburgh, where he built two crucible steel melting furnaces of the same type. After that he spent some time in the office of the Siemens agents in Boston and also at steel works in different parts of the country, starting crucible steel furnaces. He then went to the Bay State Iron Works in South Boston, Mass., where he built the first open-hearth furnace that was a commercial success in the United States. It made steel of a much better quality than had previously been made in this country. The principal use to which it was put in those days was the manufacture of locomotive fire-boxes. From South Boston, he went hack to the old works in New Hampshire where his father was still superintendent, and built for it an open-hearth furnace, a plate mill, and a bar mill. In 1873, Mr. Wellman went to Cleveland to design and build the plant of the Otis Steel Co. He remained with this company for 16 years as engineer and superintendent. During this time he developed the open-hearth charging machine and introduced the electromagnet for handling pig iron and scrap steel. The first charging machine was operated by hydraulic power, and although it was not entirely satisfactory it performed the work fairly well and encouraged its inventor to build another one, which was driven by electric motors. This proved

Jan 1, 1920