Search Documents

By Frederick Laist, Howard Aldrich

The object of the construction and operation of the 80-ton leaching plant was to test out the leaching of sand tailings on a large scale and, if possible, determine a definite method of operation, and the best construction for the larger unit which is now being built. It was also of importance to obtain some practical data as regards cost items. The 80-ton plant was not expected to be a commercial success. A leaching process on such low-grade material necessitates the treatment of a very large tonnage. Such a cost item as labor, for instance, is entirely out of proportion in such a small plant. The amounts of acid, salt, scrap iron, and fuel for roasting, however, are the same per ton in an 80-ton plant as in a 2,000-ton plant. These costs were definitely established. Also the percentages of extraction and grade of tailings were definitely determined for a large-sized unit. Following will be found the description of the plant, the method of operation and the- results obtained. A general view of the plant is given in Fig. 1. The bins consisted of one coal bin with a capacity of 30 tons, one salt bin with a capacity of 20 tons, and a "mill tailings" or feed bin which held 70 tons. The coal and salt bins were placed with their floor level even with the firing floor of the roasting furnace. The feed bin, to give it greater capacity, discharged about 12 ft. below this point, to a 12-in. conveyor belt, which in turn discharged into a pug mill. This fed another conveyor belt, which discharged into the top hearth of the furnace. The furnace was an ordinary six-hearth MacDougall roaster, 20 ft. in diameter. It was equipped with two fire boxes, on opposite sides, the flames entering on the third hearth. An induced draft was obtained with a Buffalo blower, worked as an exhaust fan. Just above the top hearth was an annular flue around the whole circumference of the furnace. Slots at intervals of about 18 in. led from this flue down into the top hearth. The slots were 2 in. wide by 6 in. long. This annular flue proved rather unsatisfactory, as it tended to fill up with flue dust and choke the dots, thus cutting down the draft. The volume of gas through

Jan 1, 1915

By I. N. Knapp

I Herewith present some notes on the use of Portland cement to cement in the casing, and for plugging, to exclude water from oil and gas wells, and the methods employed. I have used my best efforts to. make each step of the operation of cementing wells perfectly clear. The information is the result of actual experience and observation. The illustrations are from original drawings made especially for this paper. Portland Cement It is not necessary to discuss here the manufacture of cement. Any established brand of the slower setting Portland cements may be purchased with the confidence that it will harden, if properly used, and exclude water from and plug wells efficiently. Setting.—By the setting of cement is meant its initial change from a soft or plastic mortar to a friable solid. After the cement has become thoroughly set it is still very weak and can be readily pulverized in the fingers. Setting is thought to be effected by the crystallizing out of the silicate and the aluminate of lime, which are soluble in water in their anhydrous form. After dissolving in the water they pass to the hydrated state, in which they are insoluble, and hence are precipitated in a crystalline form. Ordinarily neat Portland cement mortar remains perfectly plastic for from 1 to 1 1/2 hr. after mixing with water at about 70" F. A higher temperature accelerates and a lower retards setting.. Hardening.—This is due to a continual crystallization of salts from solution, and to further chemical and physical changes which develop slowly, but which continue for long periods of time. Testing.—It is no more necessary for an operator to go into the scientific testing of cement to be used in a well than to so test the pipe used. He must depend for the quality of each on the tests and reliability of the manufacturer. Cement or pipe may be damaged in shipment so

Jan 1, 1915

By Charles L. Parsons

Early in 1912, from information received by the Bureau of Mines, it became evident that quantities of valuable radium-bearing ore from Colorado were being exported for manufacture in foreign countries and that at least part of the manufactured product was being returned to this country and sold at a price entirely incommensurate with that received by the miner and the prospector. Consequently, in line with its efforts to increase efficiency in the mining and treatment of mineral resources, the Bureau of Mines undertook an investigation of conditions. Results of this preliminary investigation were published, in the summer of 1913, as Bulletin 70,a which gave an outline of the radium deposits of the West, the conditions of mining, the wastes involved, and the status of the production of radium from its ores. At about this time newspapers and medical journals were publishing statements regarding the value of radium in cancer therapy. These reports, although many of them were exaggerated, brought out clearly the remarkable virtue of the gamma rays for the treatment of cancer and other malignant growths. In view of the fact that the largest known supplies of radium ore in the world are in the States of Colorado and Utah and on the public lands of the United States, it was deemed highly important for the Bureau of Mines to study the production of radium in detail. Such study, it was hoped, would enable the prospector and miner to obtain a fairer price for the ores and would furnish information necessary in case Congress appropriated funds to develop methods for extracting radium from ore on the public lands under Government supervision, to be supplied at cost to the hospitals of the Army, Navy, and Public Health Service.

Jan 1, 1915

By Boyd Dudley, R. H. Richards

In nearly all ore-dressing operations it is a common practice to discharge mixtures of fine ore and water through spigots; for example, from classifier pockets, from jig hutches, from settling tanks, etc. As a general rule it is desirable to regulate the composition, i.e., the ratio of water to sand, of such discharged products; and this can usually be done by varying the size of the orifice or spigot through which the material is discharged. Thus it is that problems similar to the following are frequently encountered: With a given quantity of solids per unit time, of a given specific gravity, to be discharged with water under a given head, and with a given ratio of water to solid, what must be the size of the spigot opening? If the spigot is to be open continuously, there are, aside from its form, but three factors governing the rate at which it will discharge a mixture of sand and water, namely: the head of water above the spigot; the area of the spigot opening; and the viscosity of the material to be discharged. The term viscosity, as used here, means the ratio of the volume of pure water that will flow through a given orifice under a given head in a given time to the volume of the material under consideration that will flow through the same orifice in the same time under the same conditions. While the actual viscosity of water containing sand in suspension is not increased by the presence of the sand, nevertheless the volume-rate at which such a mixture will flow through an orifice is less than that at which pure water will flow, by reason of the friction of the particles of sand against each other and against the sides of the orifice. In other words, the flow is retarded as it would be by increased viscosity; and therefore, for the purpose in view, we may speak of the viscosity of a mixture of ore grains and water as defined above. The head of water above the spigot is generally fixed by the form and design of the classifier or tank to which the spigot is attached. So, with the head known, in order to determine the size of the spigot required it is necessary to know the viscosity of the desired mixture, and the coefficient of discharge of

Jan 1, 1915

By E. C. Harder

Few mineral deposits have in recent years attracted such general and widespread attention as the Brazilian iron-ore depositis…

Jan 1, 1915

By Arthur G. Levy, Henry M. Howe

$1. Introduction.—Any given piece of metal is made up of a very great number of grains, usually microscopic, each of which is a perfect crystal save only in outward form, with cleavage planes of low cohesion, geometrically arranged quite as in fie familiar non-metallic crystals. The plastic deformation of such a mass occurs chiefly through the slipping of the crystalline blocks of which each grain is composed along these cleavage planes, causing steps called slip bands to form on a previously polished surface. In this slip, the metal immediately adjoining each of the cleavage planes along which the slip takes place is thought to pass extremely rapidly through a very mobile state into the amorphous state, in which it is harder than the remaining still crystalline metal between the amorphous layers thus formed along the slip planes. Whether the slip planes below the surface in ferrite can be detected by cutting, polishing, and etching sections is in dispute; but if this detection is possible at all, it is usually made impossible by heating the metal even gently. In short, the change along the slip planes does not persist through heating, and it is thought not to persist through time even at the room temperature, nearly all the amorphous metal recrystallizing. The network in Fig. 22 and the parallel N.-70-E. lines in Fig. 21 are slip bands in copper. When plastically deformed metal is heated, certain parts of certain grains may twin, that is, their component crystalline units may rotate into a position, or more exactly into an orientation, symmetrical with the initial orientation and hence with that of the remainder of that grain. As seen in a microsection of a metal the twinned areas usually have parallel sides. The existence of twinning is recognized in metallic sections either by the presence of such parallel-sided areas differing in brightness from the adjoining metal, especially when seen under oblique light after etching, or more surely by the zigzagging of the slip bands which form when twinned metal is itself deformed again. Hence the usual procedure in developing twins is to deform plastically so as to cause the twinning tendency; to heat so as to allow the tendency to assert

Jan 1, 1915

By Ira B. Joralemon

The Ajo copper district is in the heart of the Arizona desert, near the western boundary of Pima county. Gila Bend, the nearest railroad point, is 43 miles north of the camp, and the little Mexican border town of Sonoita is 30 miles south. Between Gila Bend and Sonoita, Ajo is the only settlement save for one or two small cattle ranches and the uncertain villages of nomadic Papago families. The Little Ajo mountains rise a few hundred feet above wide desert valleys, beyond which are lava mesas. The camp itself lies at an elevation of about 1,900 ft. above sea level, in a little basin on the east side of the range, separated from the open desert by low hills. In the center of the basin the brilliantly iron and copper stained rocks of Copper mountain rise 150 ft. above the village. Many varieties of cactus and low desert bushes cover the hills, while in the large valleys there are clusters of mesquite, paloverde, and ironwood trees which furnish limited amounts of fairly good fuel. A scanty supply of water is obtained from wells in the desert and from- prospect pits in the camp. The nearest abundant source of water is the Gila river, 50 miles north of Ajo. (See Fig. 1.) , History of the Ajo District The Ajo, next to Senta Rite, New Mexico, is claimed to have been the first copper district in the Southwest worked by Americans. In the '60's or even earlier high-grade native copper and cuprite ore was mined from shallow surface workings and hauled by bull team 400 miles across the desert to San Diego. From there it was carried in sailing ships to Swansea, Wales. Later, the ore was hauled to Yuma, floated down the Colorado river to the Gulf of California, and shipped to Swansea. Bat-infested old workings and the massive axles of the bull carts are shown to prove the truth of the stories. From this early period until the beginning of the present century, the Ajo district was worked only in a casual and intermittent way. With the increased interest in copper mining during the past decade, the brilliant

Jan 1, 1915

By Joel H. Watkins

The terms kaolin, china clay, ball clay, and paper clay are more or less loosely and interchangeably applied to a large class of white-burning clays. These clays are made up chiefly of hydrous amorphous (colloidal) aluminum silicates with variable amounts of free silica and other impurities in small quantities. Occasionally also the term kaolinite is wrongly applied to a white-burning clay, for kaolinite is a mineral of definite chemical composition and definite crystalline form which occurs but sparingly in nature. It is not the purpose of this paper, however, to define or classify clays, or to enter into a discussion of the chemistry of clays. It is rather a general description of the occurrence and methods of mining of a kindred group of clays, and a discussion of their future economic aspect. In the Southern Appalachian States, the mining of white-burning clays has in recent years become an important industry. Although these clays are of several distinct types, which occur in as many localities under different geologic conditions, they are for the most part primarily of the same origin. They are essentially the same in elementary constituents, and are largely consumed in the game industrial arts. From the standpoint of a mining engineer, therefore, and for convenience in comparison and correlation, it should be interesting to discuss them under one heading. Kinds of Clay The most important types of clay which are now being actively mined in the Southern Appalachian States and with which this paper is particularly concerned are the North Carolina, Virginia, and Georgia kaolins or china clays (residual); the South Carolina and Georgia kaolins or paper clays (sedimentary); and the Florida and Tennessee plastic kaolins or ball clays (sedimentary). Other varieties which are interesting but which are as yet of little importance are the pocket deposits of white clay in Augusta County, Virginia, the bauxitic kaolins of Tennessee,

Jan 1, 1915

By C. M. Weld

The southeastern coast of China, from Ning-Po to Macao, represents an element in the continental mass of Asia which has at practically all times in the remote past exhibited a tendency to rise father than to subside.

Jan 1, 1915

By Philip W. Henry

There is a difference of opinion among engineers on the subject of depreciation in general, and still more on its application to any given case The committee which was appointed by the American Society of Civil Engineers to make a report on Valuation of Public Utilities, states "There is no subject connected with valuation about which there are more diverse views than those relating to depreciation;" and in the discussion which took place upon the presentation of the preliminary report of this committee in January, 1914, that part of the report dealing with depreciation called forth more discussion than any other. From this discussion it was evident that the word "depreciation" was not always used in the same sense, so it is quite important that some definition be adopted. As this paper relates to the proper method of treating depreciation by corporations or individuals operating oil properties, both of which must make a return of annual net income to the government in connection with the income tax, it will be in order to adopt the definition of the Internal Revenue Bureau. Under date of Mar. 29, 1910, the Commissioner of Internal Revenue of the Treasury Department stated "Deduction on account of depreciation of property must be based on lifetime of property, its cost, value and use." Again, on Form 1035, "Return of Annual Net Income" for miscellaneous corporations (Section 2, Act of Congress approved Oct. 3, 1913), a deduction from gross income is allowed for "Total amount of depreciation for the year." This item is defined more particularly as follows: "The amount claimed under Item No. 5 (b) for depreciation should be such an amount as measures the loss which the corporation actually sustains during the year in the value of buildings, machinery, and such other property as is subject to depreciation on account of wear and tear, exhaustion, or obsolescence. The amount taken credit for on this account in order to be allowable should be so entered on the books as to constitute a liability against the assets of the corporation. The amount claimed under this item should not cover losses in the value of stocks and bonds. Decrease in the book value of securities owned, so far as such decrease represents a decline in the actual value of such securities, should be deducted under item 5 (a) of the return. "Where depreciation of physical property is made good by renewals, replacements,

Jan 1, 1915

By Stuart Croasdale

Not long ago I was called upon to conduct some experiments on the treatment of ores from the New Cornelia copper mine, Ajo mountains, Arizona, for the Calumet & Arizona Copper Co. The problem was a very interesting one and contained some unusual features. Incidental with this problem was the utilization of a large amount of low-grade pyrite in the Bisbee mines of the company, provided this could be accomplished by any feasible method. The New Cornelia mine is situated 45 miles south of Gila Bend, the nearest railroad point, on the Southern Pacific Railroad. It is about 160 miles, almost due west, from Tucson. This section is one of the most arid in the United States. The normal annual precipitation, as given by the United States Weather Bureau covering a period from 1870 to 1901, is 3 to 5 in. During June and July, 1913, the records kept by the company gave the following results. These are all I have available, but they show the enormous evaporation that can be expected, which may be a factor in leaching operations on a large scale. Temperature, Degrees F. High Low Average June...................... 112 62 84.0 ' July...................... 115 71 87.8 Evaporation June July Concrete tank, inches............ 11.7 10.72 Iron tank, inches.............. 14.8 13.07 Rainfall, inches................ None 0.77 Cloudy days................... None 10.00 Aside from several springs about 10 miles from the property, the nearest known water in quantity at the time these experiments were made was the Gila river at Gila Bend, 45 miles distant. Part of the developinent of the property of course included drilling for water in the valley, which was in progress at the conclusion of my experiments. The ore deposit itself is unusual. It consists of of intrusive plug of monzonite or granite porphyry. Chalcopyrite, bornite, and magnetite are finely disseminated throughout the magma in sufficient quantities to make the greater part of the mass commercial ore to a certain depth.

Jan 1, 1915

By Manuel Eissler

The material presented in this paper is an abstract of a thesis submitted by the writer to the faculty of the Massachusetts Institute of Technology, as part requirement for the degree of Master of Science. The investigation was undertaken at the suggestion of Prof. H. 0. Hofman, and it was conducted, under his direction, in the laboratories of the Mining Department of the Institute. The purpose of the work was, first, to study some of the reactions that have been considered as a part of the mechanism of the chloridiz-ing roast, and second, to study the conditions under which nickel oxide and copper oxide may be chloridized. While the production of chlorine gas by various reactions during the chloridizing roast may not be primarily useful in the chloridation of metal oxides and compounds, it nevertheless serves a useful purpose in preventing the dissociation and decomposition of chlorides once they have been formed; for example, the dissociation of cupric chloride into cuprous chloride and chlorine. Therefore it was thought that a study of some chlorine-producing reactions would prove of interest, and the first series of experiments dealt with this phase of the subject. he object of the latter part of the work was to show the possibility of treating heavy sulphide ores, such as those of Sudbury, Ontario, containing much iron and small amounts of copper and nickel, by chloridizing and removing the copper, leaving an iron-nickel oxide product suitable for smelting in the blast furnace for nickel-bearing pig iron. The chloridizing of the copper would, of course, be preceded by a roast for the removal of sulphur, the sulphur oxides being available for the manufacture of sulphuric acid, if under the local conditions this product would be of commercial value. Reactions of the Chloridizing Roast Reaction of Sodium Chloride, Sulphur Trioxide, and Oxygen.—The first reaction studied was that involving the production of chlorine

Jan 1, 1915

By Irving A. Palmer

During the past 15 years in this country there have been few additions to the literature of lead smelting. After the consolidation of the principal smelting companies at the beginning of this period it became the policy of the larger company not to permit the publication of details in regard to many of its metallurgical processes. This led to similar action on the part of some of its competitors. The result, of course, was a decided decrease in the number of papers written upon the practical side of the subject. Even upon the theoretical side the contributions have been few. It would seem that the industry as a whole has suffered from this general unwillingness to exchange information. While it is true that a given company is entitled to the reward that may come from its own development of a new process, it is also true that a still greater reward might be the result of a free exchange of ideas with other plants. This principle has been recognized for a long time in other metallurgical industries, notably those engaged in the smelting of iron and the manufacture of steel. It is pleasing to note that the leading lead-smelting company has very recently decided to modify its policy of secrecy, and to permit the publication of papers covering some details of its metallurgical methods. The statement has been made that there has been but little progress in lead smelting during the period just referred to. This impression is due in part, no doubt, to the scarcity of papers written on the subject. 'There has been, it is true, some discussion of the new sintering processes, but with little reference to detail, and to the effect that blast roasting has had upon the industry as a whole. In spite of the prevailing belief, it may be said that lead smelting, in common with other metallurgical industries, has made steady and substantial progress. It is the purpose of the present paper to discuss briefly some features of the industry as it is now conducted, with special reference to the blast-furnace practice in the larger silver-lead smelting plants of the United States and Mexico.

Jan 1, 1915

By W. C. Phalen

The production of salt in the United States divides itself at the outset into two distinct classes…

Jan 1, 1915

By N S NONE

Jan 1, 1915

Jan 1, 1915

Jan 1, 1915

Jan 1, 1915

Meeting of Nov. 20, 1914.-Charles F. Rand was unanimously elected as the representative of the Institute on the John Fritz Medal Board of Award. E. Gybbon. Spilsbury was unanimously elected to succeed himself in January, 1915, on the Library Board of the United Engineering Society. . The President appointed Messrs. Walter Douglas, Charles E. Mills, and L. D. Ricketts as delegates to the seventeenth National Convention of the American Mining Congress, Phoenix, Ariz., Dec. 7 to 11, 1914. It was voted that the sum of $857.61, or so much of it as may be necessary, be advanced to the Land Fund from the general funds of the Institute, in anticipation of the collection of unpaid installments of subscriptions to the Land Fund; and that the Treasurer be instructed to pay to Andrew Carnegie at the present. time the sum of $2,500 on account of the Land Fund indebtedness.

Jan 1, 1915

By Henry D. Hibbard

The object of this report is to give briefly information of present value relating to the manufacture and uses of the various commercial alloy steels, with the hope of stimulating the demand for such steels and extending their practical use. The report is issued by the Bureau of Mines as a contribution to the increase of efficiency in the preparation and utilization of the mineral resources of the United States. Alloy steels are included in the so-called special steels, but as the latter term is often used in the mills to designate broadly any steels intended for purposes other than those served by the regular product, it has seemed best to use the more specific term of alloy steels in this report. Alloy steels are bringing about a series of revolutions in various in- dustrial fields in which steel plays an important part. Most elements that could be procured in sufficient quantity have been alloyed with iron in various proportions, either alone or in combination with others, in the search for useful alloy steels. Those steels that have gained and maintained for themselves a place in current use are discussed in this report. Some of them have had an ephemeral life of usefulness which would no doubt have been prolonged had not some other more satisfactory steel been developed. Probably the first useful alloy steel was Mushet's self-hardening tungsten tool steel, patented in 1868. Fifteen years later chromium steel, really containing chromium, was struggling for recognition for some purposes, the chief of which was for the manufacture of solid shot for piercing armor. In both of these steels the effect of the alloying element as used was in a way proportional to the amount contained. In 1882 Hadfield made his epoch-making discovery of manganese steel and demonstrated that in iron metallurgy it is not safe to take for granted anything as to the properties of an alloy of iron with other elements, basing one's opinion on past experience and knowledge, and that the effect of an alloying element may not be proportional to its content. The development of useful nickel

Jan 1, 1915