Search Documents

By Shiou-Chuan Sun

THIS paper presents the design and operation of a frothmeter capable of measuring the frothing characteristics of pine oils and other frothing reagents. The experimental data show that the froth-ability of pine oil is governed by: 1—rate of aeration, 2—time of aeration, 3—height of liquid column, 4—chemical composition of pine oil, 5—pH value of solution, 6—temperature of solution, and 7—concentration of pine oil in solution. The effect of mineral particles on the behavior of froth also was studied, and the results can be found in a separate paper.' The results also show that the relative froth-abilities of pine oils in the frothmeter generally correlate with those in actual flotation, provided that other factors are kept constant. In addition to pine oils, the other well-established flotation frothers were tested, and the results are included. In this paper, compressed air frothing is the frothing process performed by means of purified compressed air, whereas sucked air frothing is the frothing process accomplished by purified air sucked into the glass cylinder by a vacuum system. The term vacuum frothing denotes that froth was formed by degassing of the air-saturated liquid under a closed vacuum system. Apparatus The frothmeter, shown in Fig. 1, is capable of re-producibly measuring the volume and persistence of froth as well as the volume of air bubbles entrapped in the liquid and is capable of being used for compressed air frothing, sucked air frothing, and vacuum frothing. Fig. la shows that for compressed air frothing, the apparatus consists of an airflow regulating system, 1-3; a purifying and drying system, 4-8; a standardized flowmeter to measure the rate of airflow from zero to 500 cc per sec, 9; and a graduated glass cylinder, 13; equipped with an air regulating stopcock, 10; an air chamber, 11; and a fritted glass disk to produce froth, 12. The fritted glass disk, 5 cm in diam and 0.3 cm thick, has an average pore diameter of 85 to 145 microns. The pyrex glass cylinder has a uniform ID of 5.588 cm and an effective height of 63 cm. The inside cross-sectional area of the glass cylinder was calculated to be 24.53 sq cm, or 3.8 sq in. For sucked air frothing, Fig. lb shows that the apparatus for compressed air frothing is used again, with the following modifications: 1—compressed air and its regulating system, 1-3, are eliminated; and 2—a vacuum system, 16, equipped with a vapor trap, 15, and a vacuum manometer, 17, is added. The vacuum system can be either a water aspirator or a laboratory vacuum pump. Any desired rate of airflow can be drawn into the glass cylinder, 13, by adjusting the opening of the air regulating stopcock, 10. The sucked air stream is cleaned by the purifying and drying system, 4-8, before entering the glass cylinder, 13. When this setup is used for vacuum frothing, the air regulating stopcock is closed. The frothmeter has been used for almost 3 years and has proved to give reproducible results, as illustrated in Table I. With a magnifying glass and suitable illumination, the frothmeter also can be used to study the attachment of air bubbles to coarse mineral particles.' Experimental Procedures Except where otherwise stated, the data presented were established by means of the compressed air method. The volume and persistence of froth were recorded respectively at the end of 4 and 6 min of aeration at a constant rate of airflow of 29.3 cc per sec, which is equivalent to 71.6 cc per sq cm per min, or 462.6 cc per sq in. per min. The aqueous solution for each test, containing 1000 cc of distilled water and 19.2 ± 0.5 mg frothing reagent, was adjusted to a pH of 6.9 0.2. The volume of froth is expressed as cubic centimeter per square centimeter and is equivalent to the height of the froth column (the distance between the bottom and the meniscus of the froth). The volume of froth was obtained by multiplying the height of froth by the cross-sectional area of the glass cylinder, 24.53 sq cm. Before each test, the glass cylinder, 13, was cleaned thoroughly with jets of tap water, ethyl alcohol, tap water, cleaning solution, tap water, and finally distilled water. The cylinder with stopcock,

Jan 1, 1953

By Shiou-Chuan Sun

THIS paper presents the design and operation of a frothmeter capable of measuring the frothing characteristics of pine oils and other frothing reagents. The experimental data show that the froth-ability of pine oil is governed by: 1—rate of aeration, 2—time of aeration, 3—height of liquid column, 4—chemical composition of pine oil, 5—pH value of solution, 6—temperature of solution, and 7—concentration of pine oil in solution. The effect of mineral particles on the behavior of froth also was studied, and the results can be found in a separate paper.' The results also show that the relative froth-abilities of pine oils in the frothmeter generally correlate with those in actual flotation, provided that other factors are kept constant. In addition to pine oils, the other well-established flotation frothers were tested, and the results are included. In this paper, compressed air frothing is the frothing process performed by means of purified compressed air, whereas sucked air frothing is the frothing process accomplished by purified air sucked into the glass cylinder by a vacuum system. The term vacuum frothing denotes that froth was formed by degassing of the air-saturated liquid under a closed vacuum system. Apparatus The frothmeter, shown in Fig. 1, is capable of re-producibly measuring the volume and persistence of froth as well as the volume of air bubbles entrapped in the liquid and is capable of being used for compressed air frothing, sucked air frothing, and vacuum frothing. Fig. la shows that for compressed air frothing, the apparatus consists of an airflow regulating system, 1-3; a purifying and drying system, 4-8; a standardized flowmeter to measure the rate of airflow from zero to 500 cc per sec, 9; and a graduated glass cylinder, 13; equipped with an air regulating stopcock, 10; an air chamber, 11; and a fritted glass disk to produce froth, 12. The fritted glass disk, 5 cm in diam and 0.3 cm thick, has an average pore diameter of 85 to 145 microns. The pyrex glass cylinder has a uniform ID of 5.588 cm and an effective height of 63 cm. The inside cross-sectional area of the glass cylinder was calculated to be 24.53 sq cm, or 3.8 sq in. For sucked air frothing, Fig. lb shows that the apparatus for compressed air frothing is used again, with the following modifications: 1—compressed air and its regulating system, 1-3, are eliminated; and 2—a vacuum system, 16, equipped with a vapor trap, 15, and a vacuum manometer, 17, is added. The vacuum system can be either a water aspirator or a laboratory vacuum pump. Any desired rate of airflow can be drawn into the glass cylinder, 13, by adjusting the opening of the air regulating stopcock, 10. The sucked air stream is cleaned by the purifying and drying system, 4-8, before entering the glass cylinder, 13. When this setup is used for vacuum frothing, the air regulating stopcock is closed. The frothmeter has been used for almost 3 years and has proved to give reproducible results, as illustrated in Table I. With a magnifying glass and suitable illumination, the frothmeter also can be used to study the attachment of air bubbles to coarse mineral particles.' Experimental Procedures Except where otherwise stated, the data presented were established by means of the compressed air method. The volume and persistence of froth were recorded respectively at the end of 4 and 6 min of aeration at a constant rate of airflow of 29.3 cc per sec, which is equivalent to 71.6 cc per sq cm per min, or 462.6 cc per sq in. per min. The aqueous solution for each test, containing 1000 cc of distilled water and 19.2 ± 0.5 mg frothing reagent, was adjusted to a pH of 6.9 0.2. The volume of froth is expressed as cubic centimeter per square centimeter and is equivalent to the height of the froth column (the distance between the bottom and the meniscus of the froth). The volume of froth was obtained by multiplying the height of froth by the cross-sectional area of the glass cylinder, 24.53 sq cm. Before each test, the glass cylinder, 13, was cleaned thoroughly with jets of tap water, ethyl alcohol, tap water, cleaning solution, tap water, and finally distilled water. The cylinder with stopcock,

Jan 1, 1953

By John R. Bartels

This report discusses an improved method for rerailing underground railcars devised in a joint effort by the Bureau of Mines and Hoesch MFD. This improved method utilizes a lightweight hydraulic ram with hand-pump activation to move a bridge-mounted roller carriage in conjunction with steel-reinforced air-lift bags. This method provides a lightweight portable system in which only two workers are required to perform the mine car rerailing operation. Because of the very narrow confines in underground mines, use of overhead cranes and other surface rail techniques is not possible. This new system is designed for very low profile work, and provides the necessary lifting force from light- weight compressed-air bottles.

Jan 1, 1985

By G. T. Homce

Most electric motor predictive maintenance methods have drawbacks that limit their effectiveness in the mining environment. The U.S. Bureau of Mines is developing an alternative approach to detect winding insulation breakdown in advance of complete motor failure. In order to evaluate the analysis algorithms necessary for this approach, the USBM has designed and installed a system to monitor 120 electric motors in a coal preparation plant. The computer-based experimental system continuously gathers, stores, and analyzes electrical parameters for each motor. The results are then correlated to data from conventional motor-maintenance methods and in-service failures to determine if the analysis algorithms can detect signs of insulation deterioration and impending failure. This paper describes system design and implementation. At this writing, however, installation is still underway, and field data analysis results are not yet available.

Jan 1, 1994

By J. West

For many years line-of-sight (LOS) issues for underground mobile equipment is a growing focus of research. This research is a result of the numerous fatalities and injuries which occur in the mining industry and which are related to poor operator LOS. Three assessment methods are currently used to assess operator LOS of underground mobile equipment. The light filament (LF) method is a hands-on assessment method that is performed in the field. This method is not evaluated in this paper. The laser scan (LS) method of assessing equipment is a quick and reliable method that comes from the need to evaluate vehicles already located in the field. The computer simulation (CS) method can assess LOS issues using a computer aided drawing (CAD) model, which is useful for assessing current or prototype models. The purpose of the current research is to compare and validate different operator LOS assessment methods. Comparison of the results of the LS and CS visibility plots yielded similar quantifiable results. A visual comparison of the results further illustrate that the LS and CS methods are acceptable assessment tools for mobile equipment operator LOS evaluation. The visibility assessment methods are now being prepared as guidelines for the mining industry to assess current and potential designs.

Jan 1, 2007

By R. Boussaa, Y. Fautrelle, K. Zaidat, O. Budenkova, B. Saadi, X-D. Wang, L. Hachani, H. Ben Hadid

"Comparison of experimental data obtained in a benchmark experiment of solidification of a Sn-3%wt.Pb ingot and numerical results of two-dimensional and three-dimensional simulations of the process is presented. The benchmark experiment consisted in solidifying a rectangular ingot of Sn-3%wt.Pb alloy using two heat exchangers. Conditions of solidification were thoroughly controlled due to six thermocouples embedded into each heat exchanger. Due to another array of thermocouples the evolution of the temperature field at a lateral wall of the crucible was registered during the whole experiment. A treatment of the temperature data provided an estimation of the velocity field in the experiment. Post-mortem analyses of the sample provided the pattern of macrostructure of the sample and qualitative segregations pattern. 2D and 3D numerical solidification models are developed to give the distribution of the solute in a solidified sample.IntroductionConvection, either natural or forced, plays a very important role during the solidification. Its intensity and flow pattern affect heat and mass transfer and, consequently, macrostructure and segregation in a solidified ingot [1-4]. The effect of buoyancy convection during solidification has been studied in many laboratory-scale experiments [5-6]. Due to these experiments a general comprehension of formation of various defects in the ingot has been achieved. However, mentioned studies were not consistent since alloys, solidification conditions and configurations were every time chosen arbitrary. That is why the role of each parameter characterizing solidification process remains unclear. Moreover, the question of reproducibility of defects under the same solidification conditions still exists. In addition, most of the experiments suffer from the insufficient knowledge of control parameters that makes difficult their use for validation of models for solidification. These parameters serve as boundary conditions for numerical modeling and their incomplete description leads unavoidably to the errors in simulations. This situation motivated us to develop a setup for benchmark solidification experiments and to perform a set of the solidification experiments which we reported in [7]. Here we presented a comparison between results obtained in a benchmark experiment of solidification of Sn-3%wtPb ingot and its numerical modeling, which was performed in two-dimensional and three-dimensional configurations."

Jan 1, 2012

By W. G. Davenport

This chapter shows how flash furnace industrial oxygen and oil requirements are affected by different: (a) product temperatures (b) conductive, convective and radiative heat losses (c) electrical energy inputs (d) hydrocarbon fuels. The calculations of the chapter are all for production of 65% Cu matte from pure CuFeS2 concentrate. Blast temperature is? 298 K throughout.

Jan 1, 2001

By Y. Y. Zhou

This paper introduces the application of CRIMM high-gradient magnetic separator in refinement of feldspar powders as well as the supporting technical outfits needed by the refining process with the high-gradient magnetic separator as main equipment. It could reduce the content of Fe2O3 to 0.03% with a deferrization rate of 85.88% from the feldspar raw ore containing 0.17% Fe2O3by using the above refining technology, producing an ultrapure feldspar product.

Jan 1, 2014

By V. C. Allison

The explosibility of a dust is favored by its fineness and content of volatile combustible matter; its explosibility is decreased by its moisture and ash content. The explosibility of a dust can be reduced by admixture of either inert dust or water. The major effect of both the inert dust and water lies in their heat capacity; they absorb the heat of the explosion flame until the temperature of this flame drops below the ignition temperature of the explosive heat. The amount of inert dust necessary to make an explosive dust non-explosive can be calculated from its proximate analysis. FOREWORD LARGE-SCALE testing of the explosibility of coal dust as conducted by the Bureau of Mines in its Experimental Mine involves a large initial investment, and a high charge for maintenance and conduct of the test; in addition the work is necessarily slow because of the time required for the preparation of the tests and the cleaning and repairing of the mine after each test. These tests have been made along practical mining lines that admit of a range of mixtures of dust varying from 5 to 10 per cent. and with gas as low as 0.5 per cent. increments. Because of the time and expense involved, efforts have been made to devise a type of gallery for laboratory use in which the results obtained in the Experimental Mine may be correlated as an aid in a study of dusts, the explosibility of which might be approximately determined quickly and at a minimum of expense. The explosibility of coal dust has been studied by a number of European investors, using small laboratory devices; among these may be mentioned the experiments con¬ducted by Galloway, Vital, Hall and Clark, Abel, Mallard and Chatelier, Thorpe, Bedson and Widdas, Engler, Holwartz and Meyer, and Taffanel, results of whose experiments have been reviewed by the Bureau of Mines., The Bureau has conducted many tests with the Frazer-Clement2 apparatus, which gives the pressures set up when the dust cloud within is, ignited with a platinum coil or tube, heated to different temperatures, but for these tests the sample must be especially prepared as to size (200 mesh) and must be dry. An attempt has been made to design an apparatus that may be used for checking and correlating the experimental tests. The first design was a wooden gallery, 8 by

Jan 7, 1925

By W. Choi

The present study revealed that the bioleachability of a chalcopyrite flotation concentrate is influenced by the semiconductor properties of CuFeS2. The overall reaction of biooxidation,

Jan 1, 1991

By M. J. Langley

Zinc ores were first discovered in Tennessee in 1856 at Jefferson City where a deposit of oxidized ore became known as the Mossy Creek Mine. From that time until 1913 small scale attempts at prospecting and mining were made in various parts of the district. The actual systematic development of the zinc deposits dates from 1913 when the American Zinc Company started operations at Mascot. Six mines are in operation by three companies and a seventh mine is being developed by a fourth company. The total daily production from the field is 11,000 tons of crude ore, which grades from 3 to 6 per cent zinc. Most of the ore bodies are large and ramiform, resembling asyrmetrical networks in which the ore shoots form channel like branches with areas of non-comercia1 rock, called blank islands. Most of the orebodies are adapted to large scale mechanization.

Jan 1, 1962

By R. J. MacLeod

"INTRODUCTIONThe removal of water or liquid from slurries and solutions is a procedure generally present in many process industries. This has prompted the development of many mechanical and thermal devices with which, I have no doubt you are al1 familiar.In the mining industry, beneficiation of ores necessitates ' the removal of water or other 1iquid from the concentrate material. The most common method of accomplishing this is by means of thickeners, vacuum filters and rotary dryers, generally all three and in that order;The use of spray drying techniques to obtain the same end has many advantages and these will be outlined here.THE PRINCIPLE OF SPRAY DRYINGA Spray Dryer consists of a cyclone shaped chamber where hot air and atomized concentrate are introduced in the upper section. (Sec figure No. 1). Efficient mixing of these two streams produce dry concentrate and moist spent air, both of which are removed from the base of the chamber.Thermal dewatering involves the product ion of heat and spray drying has no special requirements in this area. Generally a direct fired air heater is used and the products of combustion whether they stem from the use of gas, oil or coal fuel go into the spray dryer along with quench or dilution air which is used to reduce the combustion gases to the desired temperature. This generally lies in the range of 1,000 to 1,600° F. In spite of these relatively high inlet temperatures, the spray drying process eliminates the need for refractory lining or indeed any special heat resistant metals except on the air inlet ducting. Waste heat may also be used even if a significant amount of contamination is present."

Jan 1, 1972

By Mark Sherman

One of the main functions of a process technology and engineering services provider is to select grinding equipment that will meet the client?s throughput rate target. Prudent risk mitigation strategies would suggest that throughput rate estimates be cross-checked using a variety of techniques. Whilst some comminution circuit designers have estimated specific energy requirements via the manipulation of the Bond specific power equation e.g. Barratt?s Grindpower and OMC?s FSAG approach, other designers have opined that the Bond Indices have no role to play in the calculation of SAG mill specific power. As a result, they have developed their own specific energy estimating methodologies, e.g. SMCC?s Drop Weight based power methodology, SPI, SAGDesign, etc. Each method has its supporters and its critics. The challenge facing the engineering provider is how to nominate an SAG mill based circuit throughput rate estimate when faced with significantly disparate specific energies calculated by the different methodologies. This challenge is exacerbated via the continuing evolution of contemporary circuit configurations such as two stage pebble crushing some of which incorporate HPGR technology as the second stage of pebble crushing. The methodology presented in this paper shows that the Bond Indices are an excellent tool for estimating the specific energy requirements for SAG mills in SAB, SABC and SSS circuits. The method accommodates primary crushed feeds, partial and or fully secondary crushed SAG mill feeds, and emulates the impact of pebble crushing on SAG specific energy. As a result, the new Bond Index based method has provided an additional tool for increasing Fluor?s confidence when predicting SAG mill based circuit throughput rates. Based on this outcome, the author proposes that the decades old conundrum of using Bond Indices to calculate SAG specific energies for SAG mill based circuits has been solved.

Jan 1, 2012

By J M. Galvin, B J. McKinnon

Lightning Ridge, Australia, is the largest opal producing area in the world. Most opal is mined from shallow underground mines by individuals or small partnerships with the industry having been protected from large-scale development to date. The safety performance of opal mining has lagged both general mining industry standards and community expectations. The application of geotechnical analysis to the opal fields has the potential to considerably reduce injuries and fatalities. With consideration of the local culture, preliminary geotechnical analysis has been applied to some current methods of work utilised at Lightning Ridge. Practical solutions have been advocated and are presented in this paper. Improvements to safety generated by these practical solutions indicate that further geotechnical research at Lightning Ridge is warranted and would be beneficial.

Jan 1, 2002

The Committee on a Standard Gauge have been constantly engaged, since their appointment, in the duties assigned to them.§ They have corresponded with different persons interested in the manufacture and use of gauges in this country, and have received from several of them important information. They have also entered into correspondence with the governments of England, France, Gerniany, and Russia through their Consuls, ant1 with Austria directly. The Consuls of Germany and France

Jan 1, 1879

By B. A. Wills

With the increasing need to mine lower grade ores, high energy-related costs in comminution are of major concern. Very fine grinding is needed to liberate the very fine mineral particles in these ores. Not only is this expensive but it leads to greater losses in 'slimes'. In the early 1970's, 50% of the tin mined in Bolivia, 30% of the phosphate mined in Florida and 20% of the world's tungsten were lost in this way (Somasundaran, 1979). Gravity concentration techniques become unacceptably inefficient for particle treatment below 25-50µm, and even flotation fails in the ultra-fine range. Two approaches can be adopted to try to overcome this problem. The first involves increasing the efficiency of existing equipment or developing new slimes treatment processes. Gravity devices such as the Bartles-Mozley concentrator have been developed for this purpose and good recovery has been reported from 100µm down to 5µm. Such machines, however, have relatively low throughputs, so that large areas of plant space are generally required. Flotation is rapidly growing in importance for the treatment of ultra-fine minerals traditionally treated by gravity concentration.

Jan 1, 1986

By D. E. Parson, W. A. Morgan

This paper offers a brief review of current literature pertaining to vacuum degassing or vacuum casting of steel as practiced in the U.S.A., Germany and the U.S.S.R. The advantages of vacuum degassing of large forging ingots, heavy section casting, for the conversion of rimming bessemer steels to killed steel and for the production of transformer steels are discussed. Operating pressures, reduction in gas contents and improvements in hydrogen segregation, steel cleanliness and mechanical properties, obtained with the various techniques, are described. The paper includes a description of an experimental vacuum stream-droplet degassing unit and some preliminary results obtained at the Physical Metallurgy Division Research Laboratories Department of Mines and Technical Surveys, Ottawa on laboratory steel melts. Experimental 500 lb direct arc, basic melts have been spray cast into either ingot moulds or dry sand moulds, held inside a vacuum tank. Also 500 lb melts have been

Jan 1, 1961

By David A. Benjamin

In 1986, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied part of the 24,600-acre Orejana Canyon Wilderness Study Area (OR-001-078), in order to evaluate its identified mineral resources. The study area, located in Harney County, 76 mi northeast of Lakeview, OR, is underlain by Miocene basalt, rhyolite flows, tuffs, and tuffaceous sedimentary rocks. No mines, prospects, or claims were found within the study area. According to the U.S. Bureau of Land Management, the tuffaceous rocks have a moderate favorability for the occurrence of diatomite and a low favorability for zeolite resources. Also, the rhyolite flows have a low favorability for the occurrence of perlite resources. However, U.S. Bureau of Mines' studies indicate that no metallic or nonmetallic resources are present in the study area.

Jan 1, 1987

By Frederick Prime

AT the last meeting of the Institute, Mr. A. L. Holley read a paper on "Steel," in which he proposes for it a definition so opposed to the one generally received, as to call for some remarks. Until within the last five or six years there has been no dispute on the subject, and it seems worth while to investigate the matter. For not only does a proper tax on all importations depend on a proper appreciation of the term steel, but it is necessary to know whether steel, or wrought-iron, or homogeneous iron are requisite in all processes of manufacture in which malleable iron is employed, on account of cost, strength, etc. Karsteu* says : " Iron may be obtained, either as an unforgeable, unweldable metal, which melts at a high heat, termed cast-iron; or as a ductile, weldable, soft metal, which can only be melted at the * Karsten, Handbuch der Eisenhüttenkunde, 3d ed., vol. i, p. 6. Berlin, 1841.

Jan 1, 1876

By M. P. Hay

"For a model to be successful it must address the concerns and needs of a target audience. Further, the model must demonstrate the same patterns of behaviour as the real system, and need only be complex enough to meet this objective. If the model is too complex it can become unusable to those who need it most.With this in mind, SUPASIM has been developed for the practical metallurgist requiring only laboratory flotation rate data as input. Some 35+ successful plant simulations have been completed since 1985. The approach of SUPASIM is to characterise an ore, organise information in an understandable way and add structure to the complex flotation situation and hence support the metallurgist to interpret the relationship between variables and optimise the flotation process.The paper describes the basis on which the model was developed and sets out to provide an insight into interpreting laboratory flotation kinetics and their physical meaning in a production plant and the influence floatable gangue has on float performance and plant design. A case study illustrates how the ratio of slow floating mineral to gangue can influence circuit design and improve recovery on a plant scale.INTRODUCTIONThere is an enormous amount of useful data in the results of a laboratory scale rate test. Each variable of fraction and rate, for mineral, metal and gangue has a physical meaning in the plant. The link between float kinetics and the plant in respect of recovery, grade, pulp density, pulp flowrate, residence time, number of stages of cleaning and circuit configuration has been established by the author in the process of developing SUPASIM."

Jan 1, 2005