Search Documents

By D. K. Chibwe, P. Taskinen

"Typical operation of industrial Peirce-Smith converters (PSCs) used in copper smelting results in several common phenomena such as excessive splashing, slopping, tuyere blockage, and low converter campaign life due to high tuyere line refractory erosion. These phenomena give rise to an inefficient operation from both a process and an energy perspective.This investigation presents numerical and physical models of flow patterns, mixing, solid-liquid mass transfer, and slag-matte phase distribution in a slice model of an industrial PSC. For physical simulations, a 0.2-scale cold model was developed. Water, kerosene, air, and sintered benzoic acid compacts were used to simulate matte, slag, injected gas, and solid additions into the PSC. The two- and three-dimensional numerical simulations of the three-phase system were carried out using volume of fluid (VOF) and realizable k- e (RKE) turbulence models to account for the multiphase and turbulence nature of the flow respectively. These models were implemented using the commercial computational fluid dynamics numerical code FLUENT.Both numerical and physical simulations were able to predict, in agreement, the mixing and dispersion characteristics of the system in relation to various blowing conditions employed in the investigation. Measurement of mass transfer characteristics conclusively indicated that fluid flow in the PSC is stratified. Both blowing configuration and volume of slag in the converters were found to have significant effects on mixing propagation, wave formation, and splashing.The splashing and wave motion in these converters are known to cause losses of metal/matte and potential production time due to the requirement for intermittent cleaning of the converter mouth, resulting in reduced process throughput. To prevent these losses and hence to increase process efficiency, we propose a combined blowing configuration using top lance and lateral nozzles. The numerical simulations were conducted on combined, as well as lateral, blowing conditions. In comparison, the recent results of the combined blowing concept were found to be encouraging."

Jan 1, 2014

By W. F. Rochow, W. C. Burke

Numerous designs of linings and accessories, including dams, lifters, and heat exchangers, contribute greatly to kiln efficiencies. Greater conductivity is achieved with basic brick than with fireclay and high-alumina refractories, depending largely upon the use of steel plates in radial joints between adjacent brick to increase heat transfer through the lining. Refractory lifters expose all portions of the load to radiant or convective heat and raise some portions to higher temperatures by cascading the load down through the path of the hot gases. AMONG the many factors involved in rotary kiln efficiency, advantageous use of refractories is of major importance. So far as kiln lining alone is concerned durability is most significant, as shutdowns for repairs are costly in fuel consumption and production losses. Aside from selection of refractories best suited to the widely varying conditions under which rotary kilns are operated, lining design and accessory constructions within the kiln are highly important. The refractory most economical for any combination of operating conditions can be selected from a wide range of alumina-silica and basic refractories, including insulating, castable, and plastic fire bricks. In several cases silica brick can be used to advantage. Alumina contents of alumina-silica refractories range from 35 to 90 pct in increments of 5 to 10 pct. In general, bricks of relatively low alumina content are best for abrasion resistance, an important property for the brick used in chain sections of cement kilns or in feed end sections of limestone kilns. High-duty fireclay bricks of approximately 40 pct alumina and 55 pct silica are used to line the intermediate zones. Super-duty fireclay brick at slightly higher cost is warranted in operation of kilns with high intermediate zone temperatures and severe spalling conditions. Alumina-silica refractories with an alumina content of 50 pct and higher, termed high-alumina brick, are available in commercial classes of 50, 60, 70, 80, 85, and 90 pct alumina content. These refractories are generally used as high temperature zone linings or placed adjacent to the basic brick-lined sections when the treatment they are required to withstand is excessively severe. Use of basic refractories is confined mainly to zones of maximum temperature and most severe chemical action. Basic refractories ordinarily employed for high temperature zone linings of many rotary kilns comprise the classes shown in Table I. Each class is peculiarly well suited to various particular combinations of working conditions. The approximate chemical analyses of these classes also illustrate differences in compositions with respect to the major components.

Jan 1, 1956

By A. L. Craven, J. P. L. Bacharach, D. B. Stewart

"Inert gas use for underground mine fir e control is a well-established mature technology in some parts of the world. This paper reviews three candidate inert gases and describes three case histories where inert gas fire-fighting technology was used in actual underground fires.IntroductionInerting is the introduction of an inert gas into an atmosphere in contact with a fire to reduce the level of oxygen and hence the intensity of the fire 10 the point of extinction. The benefits of inerting include:a. Reduced Explosion HazardBy displacing oxygen from the atmosphere surrounding the fire the risk of secondary gas explosions is reduced. For example, simple methane-air mixtures at standard temperature and pressure are non-explosive below 12% oxygen. In actual mine fires, combustible gases may include hydrogen and carbon monoxide as well as methane. Such gases are also rendered non-explosive with oxygen removal to below 40/0. Fuel-rich oxygen-deficient mixtures can however be made explosive through dilution with air. Such dilution can occur downwind of the fire. It is also important to remember that the atmosphere in a sealed-off fire zone is rarely homogenous.b. Reduced Fire Intensity and SpreadIn a fire zone the initial combustion may well set alight materials surrounding the fire. Inerting can reduce the intensity and spread of secondary combustion and can cool the area surrounding the fire zone after the fire itself has been extinguished.c. Reduced Air LeakageLeakage of air into sealed areas in excess of the natural leakage may be reduced either by introducing inert gas into the leakage paths to replace air or by pressure balancing seals and providing a chamber of nitrogen on the outbye side of the seals. Both methods assist in the reduction of the intensity of combustion and hasten oxygen starvation."

Jan 1, 1986

By N. Dahata

Earlier research has indicated that an addition of titanium master alloy to aluminum alloys, results in improved fillability, grain refinement and finer pores. B206 alloy differs from other alloys used in automotive industry, with lower titanium level. This paper examines the effect of alloy chemistry (copper and titanium levels) and grain refinement (A1-5`)oTi- 1%B grain refiner) on grain size, microstructure and microporosity in B206 aluminum alloy. In this study, characterization of grain size, microstructure and microporosity was carried out using light optical microscopy (LOM) and scanning electron microscopy (SEM). Results have shown that the addition of 0.05 wt % titanium resulted in grain refinement of B206 alloy. With an increase in titanium to 0.25 wt further grain refinement, much reduced pore size and uniform distribution of pores resulted. These results suggest that B206 with proper addition of titanium has a promise as an alloy for automotive casting.

Jan 1, 2007

By K. Moxham, A. Smit, R. Pickering

Since the early 1970s research has been ongoing to develop a cost-effective way of continuously mining the narrow reef, hard rock, typical of South African gold and platinum mines. In the late1980s it was shown that impact ripping was a practical solution for the deep gold mines. In March2001 Lonmin and Sandvik agreed to co-operate in an endeavour to design and manufacture a prototype narrow reef mining machine with the ultimate aim of producing such a machine on a commercial basis that would enable Lonmin to create a safer and more productive environment within its mines and for Sandvik to enhance its leading position as a supplier of a new generation hard rock cutting machine. This paper describes the developed technology, the current progress of the delivery of the required objectives and the optimum mining layout for the roll-out of the mining method.

Jan 1, 2006

By G. W. Poling

This paper evaluates current environmental protection legislation, guidelines and criteria, focusing mainly on the land and water disposal of mill tailings. Effluent criteria and regulatory mechanisms are proposed, and submarine tailing disposal is discussed at length. The importance of basing regulations on the best available rationale is stressed.

Jan 1, 1979

By J. Szekely, Robert G. Lee

Calculations are presented for the prediction of the combined radiative-convective heat loss from molten steel held in a ladle, covered by initially molten slag. A mathematical formulation is given and numerical solutions are presented of the resultant partial differential equation. It is shown that a slag layer of about 2 to 3 in. thick would prevent any significant heat loss from the top metal surface for Periods of up to 1 hr. For thinner slag layers (or in the absence of the protective slag) appreciable heat losses would occur; plots given in the paper allow the quantitative evaluation of the fall in the metal temperature due to this heat loss. The ironmaking-steel processing operation involves several intermediate steps where the molten metal is held or transfered in ladles. The quantitative assessment of the heat losses occurring under these conditions is of considerable importance in process design considerations since the temperature of the metal may have to meet rigid specifications in any given part of the processing sequence. While the metal is held in a ladle, heat is lost by two mechanisms: i) by conduction into the ladle walls; ii) by radiation and convection from the top surface. Calculations relating to the conductive heat loss, are readily made and information may be found in the literature both on data pertaining to metallurgical situations and on the techniques that are available for performing additional computations.'-3 The evaluation of the combined convective-radiative heat loss is less straightforward, especially when there exists a protective slag layer covering the metal. In this latter case, as the top slag surface loses heat partial solidification may occur and the latent heat thus given up by the slag may represent an effective barrier to the heat loss from the metal. A semiquantitative assessment of the role played by the slag in preventing heat loss from the metal has been made in a previous paper,4 where it was shown that a slag layer 6 in. thick would act as a near-perfect insulator for periods of up to 2 hr. However, this first paper reported on an essentially preliminary investigation that considered only one slag layer thickness; furthermore, the boundary conditions used for the calculations were somewhat restrictive since no allowance was made for changes in the metal temperature. The purpose of this second paper is to extend the scope of the preliminary investigation previously reported by: i) considering several slag layer thicknesses; ii) allowing for variations in the metal temperature; and finally iii) by performing calculations on the net loss from the metal rather than from the slag surface. FORMULATION Consider a slag phase extending from y = 0 to y = L1, covering a metal phase that occupies the region extending from y = Ll to y = L, as illustrated in Fig. 1. Denote the slag and metal temperatures by TS and Tm and assume that initially both slag and metal are molten, having a uniform temperature Ti. At time = zero the surface represented by the y = 0 plane (top slag surface) is brought into contact with cold air, the temperature of which is given as T Thus for time > zero, heat will be transfered from the slag to the air by natural convection and thermal radiation; as a result of this heat loss the slag temperature will fall and after some time a solid phase is formed and a solidification boundary (more realistically described as a zone) will move progressively from y = 0 toward y = L1. Once the region of temperature gradients, moving ahead of the solidification zone, reach the slag-metal interface (y = L1) there will be a net transfer of heat from the metal through the slag to the cold air, across the y = 0 plane. In the formulation of moving boundary problems, involving phase changes that require computer solution, it is convenient to represent both phases by a single equation, making allowance for the latent heat of solidification by assigning an appropriate temperature dependence to the specific heat content. Thus the energy equation for the whole of the slag may be written as follows:

Jan 1, 1969

By G. Akdogan, C. Bergmann, C. J. Coetzee, Q. G. Reynolds, S. J. Baumgartner

Submerged arc furnaces (SAF) are used extensively in the production of ferrochrome, where charge material – consisting of mixtures of carbonaceous reductants, fluxes such as silica, and ore in the form of pellets – is fed through chutes into the vessel. The feed typically forms a thick bed or ‘burden’ of solid particulates above a bath of molten material below. This burden layer surrounds three electrodes, which are typically arranged in a triangular configuration in circular SAFs. A major challenge in the industry is the availability of sought-after reductants, volatile market conditions, and increasing electricity tariffs in South Africa. A good understanding of the physical properties of the raw materials in the charge is therefore of great value in order to best deal with the reductants available at any given time, and thereby maximising furnace throughput. This paper presents a study of the effects of different particle properties on particle flow behaviour relevant to SAF operations. Discrete element model (DEM) simulations were used to estimate the sensitivity of the particulate flow of beds of charge material to properties such as the coefficients of friction, particle shape and size, and others. The present study lays the groundwork for the development of full DEM models of the SAF that will greatly improve understanding of the flow of complex mixtures of solid particles in the submerged arc furnace, and how the relative physical properties of each component in the charge can influence electrical behaviour of the burden.

Sep 1, 2021

By Jacob Petersen, Jon J. Kellar, Samuel Kessinger, Kiran Green

Belle Fourche Shale was processed and characterized for use as a clay-based ceramic. The shale was wet sieved to produce particles that were ± 150 μm. X-ray diffraction (XRD) revealed that the -150 μm material was enriched in clay content compared to the unprocessed materials, whereas the oversize material was enriched in quartz compared to the undersize sample. Particle size analysis was performed on the—150 μm sample, which showed that the median particle size was around 10 μm. Scanning electron microscopic (SEM) analysis further confirmed the small plate size, which appeared to be primarily layered clay particles. Next, the -150 μm particles were rolled into a green body, dried at room temperature, and fired at 998°C. The fired piece was analyzed by XRD and contained 6 wt% hematite, 55% quartz, 19% microcline, and various other minor amounts of minerals. When fired at 1152 ℃, mullite was found with increasing hematite compared to the 998 ℃ firing. A multi-spectral analyzer was used to quantify the color change of the 998 ℃ fired (orange) to the 1152 ℃ fired (red) samples. Micro-computed tomography (Micro-CT) of the unfired body exhibited very few large pores, while the piece fired at 998°C also exhibited few and small pores, the overall porosity of the fired body increased. Microhardness data, obtained from the aforementioned samples, resulted in Vickers Hardness (HV1.0) values of 70.8 HV1.0 (998 ℃) and 485.7 HV1.0 (1152 ℃). Three-point bend testing was performed, giving an average strength of 23 MPa on pieces fired at 998 ℃. The average bending strength of the samples fired at 1152 ℃, was 55 MPa.

Sep 26, 2023

By N. G. Johnson

ALL of us are only too familiar with the fact that first the defense program, and finally the war, required vastly increased production from existing sources, and the discovery and development of new sources of minerals and metals. For this vast program, the explosives industry was well prepared. I use the term "well prepared" to cover all the phases of explosives service, which include formulation, design, manufacture, distribution, and application.

Jan 1, 1944

The object of this program was to design and build a self-contained system for remote monitoring of the atmosphere in mines. The system developed uses the mine pager phone line as the primary communication channel and also has the capability of using 208 Hz in the ELF band for wireless transmission through the earth. The depth for through-the-earth transmission is expected to be about 80 to 90 meters in high conductivity soil and is limited by the noise level in the ELF band-pass filters. The underground components of the TEM System are energized by mine power through a battery charger - storage battery power supply. In the event of mine power failure the battery capacity is more than sufficient for one week's operation with interrogations every four hours.

Jan 1, 1980

By J. R. Goode

"Canada developed pioneering rare earth solvent extraction methods to recover the rare earths and thorium as by-products of uranium recovery operations in Elliot Lake, Ontario, and was a major supplier of these key elements from about 1960 until 1990. At one stage, Elliot Lake was supplying perhaps one third of the world’s yttrium as well as much of its thorium. This paper reviews the development of Canada’s early rare earth and thorium production facilities. INTRODUCTIONThe rare earths and thorium were first identified in the early 19th century but were little more than curiosities for the next century. However, in the mid-1960s the invention of rare earth-based phosphors for the cathode ray picture tube used in colour television sets launched a major demand for certain rare earths.The use of thorium as an alloying agent in aircraft and missiles grew rapidly in the late 1950s. In the same period, demand for uranium for both weapons and power production soared. Also in the late 1950s, the Elliot Lake uranium-thorium-rare earth deposits (also known as the Blind River deposits) were discovered. This conjugation of events led to uranium production in the Elliot Lake camp, quickly followed by the co-production of thorium and, later, the rare earths.Uranium production in the Elliot Lake camp continued from 1955 to 1996. Thorium was produced continuously from 1959 to 1969. Rare earths were produced, intermittently, from 1965 to 1990. Complete production records are not readily available but unquestionably Elliot Lake made a significant contribution to world thorium and the rare earth production. This paper, presented earlier in an abbreviated form (Goode, 2012), is intended to present as much of the information that is available."

Jan 1, 2012

By Scott Jones

New Mexico Coal Operations ?San Juan, La Plata, And Navajo Mines ?Three Sites 100% Owned By BHP Billiton ?San Juan And La Plata Mines Owned/Operated By San Juan Coal Co. Supplies Coal To San Juan Generating Station ?Navajo Mine Located On Navajo Nation Lands Supplies Coal To Four Corners Power Station

Jan 1, 2008

A hard lump char containing only 4 to 5 per cent ash, 0·25-0·30 per cent sulphur and a trace of phosphorus has been produced from Latrobe Valley brown coal by slow drying and carbonization of ordinary industrial briquettes at temperatures between 7000 C and 14000 C. The briquette char can be made with a variety of reactivities by varying the maximum temperature of carbonization; the higher the temperature, the lower the reactivity. The strength of the fuel compares favourably with metallurgical coke made from black coal, though it may not be quite so resistant to abrasion. Experiments in a small experimental cupola indicate that it will make a satisfactory fuel for use in iron foundries. It may also find extensive application as a smokeless fuel in other branches of industry and in household heating appliances.INTRODUCTIONVictoria, like South Australia and Western Australia, is apparently without 'significant deposits of black coal of coking quality but there are huge reserves of brown coal of high moisture content (60-66 per cent) in the Latrobe Valley (well over 20,000 million tons have been proved) and there are other important deposits in the south central portion of the State (Herman, 1952).For three decades Victorian industries, including a few metallurgical firms, have been using the briquettes made at the Yallourn factory of the State Electricity Commission of Victoria (S.E.C.). These briquettes, having a moisture content of about 15 per cent and a calorific value of approximately 9,500 B.T.U. per pound, are satisfactory for certain grate-type furnaces but they are not suitable for use in cupolas of other shaft furnaces because they disintegrate badly on rapid heating.

Jan 1, 1956

By J J. Laas, A J. S Spearing

Considering the capital outlay, running costs and inherent difficulties of backfilling operations at depth the benefits need to be clearly established, quantified and then exploited. Expansion of Vaal Reefs Exploration and Mining Company towards even deeper, highly faulted ground, and the process of establishing codes of practice for the management of rockfalls and rockbursts, required that a sound support strategy be formulated. This paper describes the derivation of an overall backfilling strategy on Vaal Reefs. Use was made of experience gained over some 12 years with backfilling. Numerical modelling was used to estimate potential benefits of backfilling the deepest mining areas still to be extracted. In exploiting a probably unique opportunity, two contiguous mining areas bounded by the same major geological structures, were compared. One was extensively backfilled and the other not at all. Shaft sinking through a backfilled stope added another dimension to the database.

Jan 1, 1998

By J Wood

Steady depletion of the world’s primary copper reserves coupled with a meteoric rise in electronic waste (e-waste) generation has led to secondary copper processing assuming an ever-increasing importance within the global copper industry. Treatment of secondary copper feeds at existing smelting operations has traditionally been performed in the Blast furnace, Peirce-Smith converter and/or anode furnace. In the past decade or more, bath smelting technologies have been preferred for the processing of these materials due to their superior environmental performance and flexibility to operate under a wide range of conditions. This paper focuses on the pyrometallurgical processing of copper secondaries in the Outotec Ausmelt TSL Furnace and some of the unique issues facing secondary copper smelters and downstream gas handling/cleaning equipment.

Aug 8, 2011

By B. Currie

Maintenance of quality electrowon copper requires an electrolyte which has suitable chemical and physical characteristics. The proper design and operation of the solvent extraction plant is essential to the quality of the electrolyte sent to electrowinning. An aspect that is not well appreciated is that the return electrolyte can have negative effects on the operation of the solvent extraction plant. Poor SX plant operation creates below optimum electrolyte conditions. High Eh in the return spent electrolyte can degrade the SX reagent with large decreases in copper transfer capacity and increases in internal entrainment. The synergistic interaction of the SX and EW plants needs a single-source design approach to address the interactions. The design elements in the SX and EW plants required to manage the electrolyte conditions are discussed.

Jan 1, 2014

By Ahmad Ghahreman, Lin Li

Silver and cupric ions have been proven to play the roles of catalysts to promote the oxidation kinetics of chalcopyrite in acid solution. In this study, the interaction between silver ions and cupric ions during ferric leaching of chalcopyrite in sulfuric acid solution has been investigated. The electrochemical study by Tafel analysis showed a significant boost of dissolution rate for chalcopyrite dissolution in Fe3+- Cu2+ containing sulfuric acid solution after Ag+ was added in the solution. For 10 ppm Ag addition, the dissolution rate of chalcopyrite increased to 7.94 ×10-6 A/cm2 from 3.2 ×10-7 A/cm2, when Ag+ was absent. On the other hand, the effect of Cu2+ on the dissolution of chalcopyrite in Fe3+-Ag+ containing sulfuric acid solution was not obvious from electrochemical measurements. The chalcopyrite leaching tests in different acid solutions showed that silver addition had an obvious catalytic effect on promoting chalcopyrite dissolution. Comparing the leaching rates of chalcopyrite leached in Fe3+ containing, Fe3+-Ag+ containing, Fe3+-Cu2+ containing and Fe3+-Cu2+-Ag+ containing sulfuric acid solutions, it was found in Ag+-Fe3+-Cu2+ containing sulfuric acid solution, the leaching rate was highest among all the aqueous acid systems. Further leaching tests suggested that with increase of the Ag+ concentration from 0 to 20 ppm, the leaching rate of chalcopyrite in Ag+-Fe3+-Cu2+ containing sulfuric acid solution also increased and reached 57.62% with 20 ppm Ag+ addition after 24 h. INTRODUCTION Chalcopyrite is the most important copper mineral in copper hydrometallurgy and it accounts for nearly 80% of the universal copper resource (Olvera, Rebolledo, Mora, Dixon, & Asselin, 2018). The hydrometallurgy of chalcopyrite has been intensively studied with emphasis on solving the slow dissolution kinetics of chalcopyrite in acid environment. A variety of aqueous systems, such as sulfate (Hiroyoshi, Miki, Hirajima, & Tsunekawa, 2001), chlorides (Liu, Chen, & Yang, 2017), and ammonia (Hua et al., 2018) have been studied to improve copper leaching. From another perspective, chalcopyrite leaching studies have indicated that the mechanism of chalcopyrite dissolution in acid solution is essentially electrochemical (Li, Kawashima, Li, Chandra, & Gerson, 2013). Therefore, extensive studies have recently been carried out to explain the dissolution kinetics of chalcopyrite in different media by various electrochemical techniques.

Jan 1, 2019

By H. M. Thorne

Oil shale, a potential source of products presently obtained from petroleum, is found in many countries. The most extensive known deposits from the standpoint of potential shale oil in place are those in Brazil and the United States of America. Mining methods used for oil shale range from open-pit operations for shallow deposits to room-and-pillar and longwall techniques for deposits with thick overburdens. Oil shales from different sources vary greatly in the amounts and types of organic and inorganic constituents. By retorting, the organic material is converted to oil, gas, and coke. The largest percentages of oil are obtained from materials having the highest hydrogen content. Over 2,000 retorting systems have been patented, but only a few have been used industrially, and no single process seems best for all types of shales or economic conditions. Shale oils have different characteristics, depending on the source rock and method of retorting. They contain large quantities of olefinic hydrocarbons and more oxygen, nitrogen, and sulfur derivatives of hydrocarbons than most petroleums. Consequently, petroleum refining methods usually must be modified for shale oil. This is particularly true in catalytic processing. Hydrogenation, even under mild conditions, improves shale-oil refinability. Several byproducts may be obtained from both the retorting and refining steps.

Jan 1, 1964

By Laas JJ, Spearing AJS

Considering the capital outlay, running costs and inherent difficulties of backfilling operations at depth the benefits need to be clearly established, quantified and then exploited. Expansion of Vaal Reefs Exploration and Mining Company towards even deeper, highly faulted ground, and the process of establishing codes of practice for the management of rockfalls and rockbursts, required that a sound support strategy be formulated. This paper describes the derivation of an overall backfilling strategy on Vaal Reefs. Use was made of experience gained over some 12 years with backfilling. Numerical modelling was used to estimate potential benefits of backfilling the deepest mining areas still to be extracted. In exploiting a probably unique opportunity, two contiguous mining areas bounded by the same major geological structures, were compared. One was extensively backfilled and the other not at all. Shaft sinking through a backfilled stope added another dimension to the database. Backfilling was introduced in 1985 and several potential spin-offs were expected. These included improved local strata control for fall of ground and rockburst conditions, regional benefits in rock mass stability and mine ventilation optimisation.

Jan 1, 1998