Search Documents

By J. E. Gray

Before specifications are discussed it may be well to define the term "Mineral Aggregates." Professor K. B. Woods (1) defined "Mineral Aggregate--An aggregation of sand, gravel, crushed stone, slag, or other material of mineral composition used in combination with a binding medium to form bituminous and portland cement concrete, macadam, mastic, mortar, plaster, etc., or alone as in railroad ballast, filter beds, and various manufacturing processes, such as fluxing, etc. " This definition is too all inclusive for the purposes of this paper; therefore, this discussion will be confined to specifications for natural aggregates which means sand and gravel and crushed stone, and limited primarily to coarse aggregate which is aggregate larger than one-quarter inch in size. To the uninitiated, this may seem to be a very limited subject on an unimportant material. However, aggregates are essential in all types of construction. The tonnage and value of these two aggregates produced in the United States during 1959 as reported by the Bureau of Mines were as follows: Sand and Gravel 729,895,000 tons valued at $728,527,000 Crushed stone 581,721,000 tons valued at $824,411,000

Jan 1, 1961

By AIME AIME

MANY of the important papers to be presented at the World Congress of Engineering at Tokyo, in November, 1929, are being furnished by members of A.I.M.E. and a list of them is given below: "Fifty Years of Physical Metallurgy,,-by H. M. Boylston, Case School of Applied Science, Cleveland, Ohio.

Jan 1, 1929

By AIME AIME

ATER the preliminary registration at which approximately 380 members and guests were registered, the 138th meeting of the Institute was opened in the Concert Room of the Palace Hotel. E. A. Hersam, chairman of the San Francisco Section, voiced a brief welcome and introduced F. W. Bradley, president of the Institute, who presided over the remainder of the morning session. After expressing the welcome of the Institute to the members and guests, he read a telegram from Secretary H. Foster Bain, extending the best wishes of the eastern staff and members for a successful meeting. He next introduced Theodore J. Hoover, dean of the School of Engineering, Stanford University, who read an address by the Secretary of the Interior, Ray Lyman Wilbur, briefly outlining California's part in the mining industry and giving the welcome of California to this meeting of the Institute.

Jan 1, 1929

By S. E. Olsen, T. Færden, G. Tranell, T. Lindstad, J. Lubetsky

The authors are lead authors for chapter 4.3 ?Emissions from Ferroalloy Production? in ?2006 IPCC Guide-lines for National Greenhouse Gas Inventories, Volume 3?. The paper discusses the methods to calculate and report emissions from the production of ferrosilicon, silicon-metal, ferromanganese, silicomanganese and ferrochromium alloys, as well as the basis for the methods and choice of emission factors. CO2 is the main greenhouse gas emission from ferroalloy production, accounting for about 95 % of the total CO2-equivalents. The most accurate method of determining emissions is to base the calculations on reported amounts and analyses of reducing agents and carbonate ores used in the process. If analyses are not available, typical CO2 emission factors for the different reducing agents are recommended. If neither reliable amounts nor analyses of all reducing agents are known, default generic CO2 emission factors for the type of ferroalloy multiplied with amount produced, can be used. The CO2 produced from bio-carbon (charcoal and wood chips) should be reported but will not be accounted for in national emissions. If any bio-carbon is used, the default generic CO2 emission factors cannot be applied. CH4 accounts for less than 1 % of the total emission of CO2-equivalents. Default emissions factors for CH4 are given for the production in open or semi-closed furnaces of silicon-metal and ferrosilicon. In the production of FeMn, SiMn and FeCr in closed furnaces the gas containing CO,CO2 and volatiles can be combusted in boilers and N2O may be formed. While reporting is not required, IPCC Guidelines recommend that the N2O-content in the off-gas is measured.

Jan 1, 2007

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members) The following is a partial list of members and guests who called at Institute headquarters during the period June 10, 1917, to July 10, 1917. Guy N. Bjorge, Boston, Mass. H. H. Lauer, Allentown, Pa. A. H. Burroughs, Jr., Britannia Beach, E. C. Lee, Pittsburgh, Pa. B. C., Canada. Montrose L. Lee, Port-au-Prince, Hayti. Karl Eilers, New York, N. Y. Eugene McAuliffe, Paducah, Ky. H. S. Emlaw, Grand Haven, Mich. R. H..McMillen, Pittsburgh, Pa. W. R. Hamilton, San Francisco, Cal. L. D. Moore, Providence, R. I. Fred N. Hays, Sharon, Pa. Fred J. Pope, New Rochelle, N. Y. E. Hibbert, Nickelton, Ont., Canada. George S. Rice, Washington, D. C. Charles Janin, San Francisco, Cal. W. G. Swart, Duluth, Minn. Milton A. Allen has resigned his position with the Federal Lead Co. and accepted a position with the Arizona State Bureau of Mines, Tucson, Ariz. L. W. Bahney has resigned as Professor at Yale University and accepted a position as metallurgical engineer with the Scovill Manufacturing Co., Waterbury, Conn.

Jan 8, 1917

By D. P. Schlick

As of June 30, 1970, Federal regulations required the operator of each underground coal mine to maintain the average concentration of respirable dust below legislative standards. As of March 1, 1971, over 152,000 respirable dust samples have been processed by the Bureau of Mines. Approximately 75 percent of underground working sections are being sampled in accordance with Federal regulations. Results indicate that 72 percent of the sections which have completed at least one basic sampling cycle are below 3.0 mg/m3, the standard in effect under the Federal Coal Mine Health and Safety Act of 1969 (P.L. 91-173). Notices of Violation were issued on 1,670 underground mines for failure to begin a sampling program; Withdrawal Orders were issued in 64 of these instances. Notices of Violation were issued on 1,121 sections where applicable dust levels were exceeded; Withdrawal Orders were issued in seven of these instances. There are 381 mining sections currently operating on permit; from the interim Compliance Panel.

Jan 1, 1971

By T. Resende, J. Sismour

"Signs in underground mines are subject to variable airflow, which carries dust and moisture. Dust buildup reduces their visibility, hampering production efficiency and safety. Underground workers commonly must stop to clean signs in order to gauge their location, or find critical supplies or services. There are currently a variety of coating products, including dust and water repellants, available on the market that have the potential to reduce dust accumulation on sign surfaces. This paper describes a preliminary study to determine their effectiveness. The study involved a practical testing protocol using a trickle rock duster and samples cut from a clean, used road sign. Product effectiveness, under both dry and wet conditions, was evaluated based on photographic evidence by comparing changes in sign luminosity after a period of rock dust application. By analyzing the frequency of different pixel luminosities on the dust-covered samples, both uniformity of dust coverage and the total amount of accumulation was assessed. Results indicate that at least one product may reduce the amount of dust buildup on sign surfaces and increase visibility. INTRODUCTION In all underground mines, visibility of signage is critical. Signs inform miners of their location, direction toward escape routes, and location of supplies. Over time, sign surfaces can collect dust and can eventually become unreadable. The rate of dust accumulation on surfaces is often particularly high in coal mines, where both mining (e.g., cutting and drilling) and rock dusting activities can contribute significant amounts of dust to the airways. Several factors may contribute to dust buildup on sign surfaces. First, basic principles of fluid and particle flow are at play. When a fluid travels past a stationary surface, the velocity of the fluid at the surface boundary is zero. If a very small dust particle moving with air collides with a surface, it does not immediately fall off since the air velocity is zero at the sign surface. (This is the same reason that dust can collect on a rotating ceiling fan.) Further, once the collision occurs, other mechanisms may help keep the particle there – including friction that resists particle falling due to gravity, and adhesive forces due to humidity and/or static charges the particle and others already on the surface. Currently, the most common way to deal with reduced sign visibility due to dust buildup is for mine personnel (e.g., a compliance foreman, supply worker) to periodically clean sign surfaces – usually just by wiping them with a cloth. As a regular activity, this solution is inefficient; in cases of emergencies, it can also pose unnecessary risks. Application of an off-the-shelf coating to sign surfaces may represent a simple yet effective way to reduce the rate of dust accumulation. There are currently a variety of products on the market that may be suitable for this purpose, including dust and water repellants."

Jan 1, 2017

By G. Bjorling

After complete dissolution of chalcopyrite concentrate in sulphuric acid in presence of nitric acid the excess of the latter is expelled by a surplus of concentrate and the last traces of nitrate removed in the mother liquor after crystallization of the copper and iron sulphates. Zinc accumulates in the mother liquor from which it can be removed by solvent extraction of zinc sulphate as a pair of ions. After dissolution of the sulphate crystals in water the neutral solution is oxidized in an autoclave at 140°C where iron sulphate is thermally hydrolyzed; the iron-free solution is taken to copper electrowinning and the cell acid after partial evaporation recirculated with the mother liquor to the leaching circuit. Total recovery of copper is about 96%; other metals like zinc and iron are concentrated in industrially usable products. At a copper price of about 70 c/lb, the method appears to be profitable also in a small unit.

Jan 1, 1976

By Tianzu Yang, Weifeng Liu, Lin Chen, Wei Chen, DUCHAO ZHANG, HUI XIAO

Carbonaceous refractory materials are widely accepted in many reducing smelting processes such as iron and ferroalloys. Oxidizing processes such as copper concentrate smelting traditionally use magnesia and/or alumina/silica refractory materials. The main objection to the use of carbon-based refractories as the exposed working lining in oxidizing applications is the potential for free oxygen to react with the carbon at high temperature, which could rapidly degrade the refractory lining. In 2013, Outotec and GrafTech conducted joint trials of a thermally conductive, carbonaceous lining for smelting copper concentrates in the Outotec® pilot-scale top-submerged-lance (TSL) furnace in Dandenong, Australia. This testwork had two equally important goals; to demonstrate the ability of carbon refractories to withstand oxidizing process conditions, while ensuring that neither furnace operating conditions nor process stability were negatively affected by the refractory material. The paper discusses the input parameters of the trials, key observations during the testwork program, and the results and conclusions from both process and refractory design standpoints.

Jan 1, 2016

By T. Wang

A new generated NaNO3 ? NaNO2 ? KNO3 ternary thermal energy storage system which has low melting point as 124°C and high specific heat capacity was studied for the short and long?term thermal stability by using the Thermogravimetric Analyzer (TGA). Based on the actual working condition of molten salt in solar two, the simulated cyclic thermal stability measurement was also conducted. The ternary system demonstrates excellent short ? term thermal stability and thermal reliability after cyclic heating and cooling processes. However, in the long ? term as well as the simulated cyclic stability measurement, large amount of weight loss was observed. Moreover, the stepwise long ? term isothermal study reveals that below 440°C the weight change is minimal and this temperature is viewed as the upper limit temperature of thermal stability for this ternary system. To determine the lost phases at high temperature above the upper thermal stability limit, techniques such as XRD and SEM are used to compare the condition of the salt mixture before and after the long ? term thermal stability study. On the basis of the comparison, it can be concluded that the major weight loss was due to the decomposition of sodium nitrite.

Jan 1, 2012

By Yogesh Prashar

Three conventional uplift tests and 12 Rapid Pile Load Tests (RLT) were performed on total of fifteen 16-inch square pre-cast concrete driven piles at a test site in Emeryville California in December of 2000. The uplift tests were performed in accordance with ASTM standards, and the RLTs were performed using a FUNDEX RLT. The RLT is carried out by dropping a mass of 25-tons on top of the pile, thereby inducing a force that is measured by a load cell. An optical lens records the vertical deflection of LED's that are mounted on the pile. Ultimate uplift and compression capacities of each of the fifteen piles were determined using the Davisson method. Soil parameters were calibrated by back-calculation (cohesion and internal angle of friction) using both the results of conventional uplift load versus deflection curve, as well as the results of the triaxial compression tests. A two-dimensional finite difference model including soil elements, and structural elements representing the test pile was setup using the computer program Fast Lagrangian Analysis of Continua (FLAC). FLAC was used to simulate both the uplift as well as the RLT. Strength increase of cohesive material was also accounted for in the analysis. Numerically simulated and theoretically computed pile capacity curves and axial deformation variation with applied load curves are in close agreement to the observed curve during the field test. Conclusions are made from this test site regarding the factors influencing results of RLT.

Jan 1, 2002

By V. Hema

Granular materials are widely used in process industries, such as chemical, pharmaceutical, cement, food, detergents, and fertilizers. Mixing, blending, calcining, reduction, heating, and granulation of these materials are frequently carried out in rotating cylinders. In all of these processes, the mixing and segregation of these granular materials is important as this controls the secondary phenomena in the rotating kiln such as heat transfer to the material. A significant amount of work is available in the literature but to date these efforts have not been able to capture the important parameters affecting the mixing and segregation in rotating kilns. In addition, the range of parameter values studied so far is rather limited. Simulations of granular materials are based on either discrete elements or continuum models. The discrete element methods (DEM) combine semi-empirical models for the inter particle interactions with the equations of motion from classical mechanics to simulate the explicit paths of all granules in a rotary kiln, thus yielding realistic predictions of the mixing process. This approach is very demanding computationally, which strongly limits the number of granules and the number of revolutions in a simulation. Continuum models dispense with the discrete particles and can therefore be scaled up more easily. But the constitutive relations that serve as the foundation for continuum modeling are difficult to come by, and often only applicable to specific systems and conditions. Here we have chosen DEM simulation for investigating the mixing and segregation behavior of granular materials in a rotating cylinder. This work is directed towards demonstrating the capability of the prediction of the mixing and segregation behavior of granular materials in a horizontal rotating cylinder through discrete element simulation. Further the effect of particle size and rotational velocity on the mixing and segregation behavior is investigated. The simulation results are quantified in terms of mixing index, mixing rate, segregation index and percolation index. Keywords: DEM simulation, granular mixing

Sep 1, 2012

By Joner O. Alves

The disposal of scrap tires has been a serious environmental problem. The treatment of this waste by pyrolysis and combustion has advantages since the landfill space is dwindling and the production of fuel becomes of technological interest. However, that processes needs a rigid control of emissions. This work presents a study of the light hydrocarbon gases (HC) generated during the burn of waste tire chips in a two-stage laminar-flow horizontal furnace. Different temperatures in the primary and secondary stage of the furnace were tested, and the oxygen/nitrogen percentage was also varied during the combustion process. A gas chromatograph was used to identify and quantify the components of the gaseous products of combustion and pyrolysis. The results showed the behavior of the gases during the burn of tires, providing valuable information to the control of hydrocarbon emissions.

Jan 1, 2010

The Technical Programme Committee-Metals Technology of The South African Institute of Mining and Metallurgy, in association with its Vaal Triangle Branch, held a one-day colloquium on 18th April, 1989, the theme being 'Ferous Pyrometalurgy: A Challenge for South Africa'. The venue was the Auditorium 100 at the campus of the Vaal Triangle Technikon in Vanderbijlpark. Project and contract management A Project and Contract Management Conference is to be held on 19th and 20th September, 1989, at the C SIR, Pretoria. Powder metallurgy The PM 90 exhibition is to be held in Wembley, London, from 2nd to 6th July, 1990. The wide range of powders, processing machinery, and powder-metallurgy components at the exhibition will reflect the growth in this highly specialist industry. Castings and forgings Exhibition organizers, FMJ International Publications Ltd, are set to build upon the success of Castings & Forgings '88, which was held as a joint event with Pat- Cast '88. Castings & Forgings '89-with Pat-Cast '89- has already generated a high level of interest, which has been reflected in the demand for stands. Furnaces FURNACES '90, the eighth in this series of exhibitions for the thermal-processing industry, will be held in Solihul, West Midlands, England, on 6th and 7th March, 1990.

Jan 1, 1989

By D. Tesh

The mining industry worldwide is facing a tremendous shortage of minerals engineers in all fields of specialization. For instance, in Australia the skills shortage in the mining industry has been identified as one of the top risks facing the mining industry. In Namibia most minerals engineers employed are expatriates, with some being Namibians who studied abroad. The minerals engineering programmes at the Polytechnic of Namibia are still in their infancy. These programmes were designed to meet the mining industry skills needs. Being young has its advantages in that lessons can be learnt from older minerals education institutions that went through similar challenges. However, this does not imply just copying and implementing their approaches, since the context differs and, to ensure sustainability of the minerals education programmes, curricula have to be customized to the local context. This paper reviews the interventions made by the Polytechnic of Namibia in order to ensure the sustainability of its minerals education programmes. The methodology consisted of an extensive literature review, a status quo analysis of the mining and process engineering department, identifying the gaps between the current state and desired state, and mapping the goals and strategic actions required to progress to the desired state. The following factors were identified as major threats to the sustainability of minerals education at the Polytechnic of Namibia: the quality of students, low student enrolment rates, low pass rates in science and mathematics, shortage of academic staff, dwindling government funding, and limited involvement of the mining industry. The major outcomes of this research comprise the detailed strategic actions employed by the Polytechnic of Namibia to address the threats to sustainability of its minerals education programmes.

Jan 1, 2014

By Reynold Q. Shotts

Data are presented which show that fractions of varying densities-from the same coals are oxidized at different rates by nitric acid. From oxidation data, the approximate quantity of "bright" and "dull" components may be calculated. Definite relationships between oxidation rate and rank are shown for density fractions from at least two bituminous coals.

Jan 1, 1950

By Christian Maguire

Tunnel contracts in New York have in recent years had few bidders with the bids received being much higher than anticipated. Since 9/11, security has become a key issue in planning key infrastructure projects in New York. This is especially true in the case of large water supply tunnels. Striking the right balance between cost and security was the major factor in determining the best configurationfor the Kensico-City Tunnel. This paper outlines the efforts made to determine realistic probable bid costs for the tunnel contracts, and the innovative approaches taken to deal with security issues.

By Ajit Godbole, Ping Chang, Ramakrishna Morla, Purushotham Tukkaraja, Shivakumar Karekal

This paper presents the optimum auxiliary fan(s) location to control air recirculation in dead-end workings where dieselpowered vehicles operate. Investigations were conducted with various secondary fan locations from the dead-end crosscut with varying the intake air quantities using a 30 m3/ s capacity twin 75 kW auxiliary fan and 45 m3/ s capacity twin 110 kW auxiliary fan to control air recirculation and DPM. The results showed that if the drive intake airflow rate matches the fan capacity, air recirculation will occur even when the fan is located 10 m away from the crosscut entry. Results also showed that if the intake drive air quantity was greater than or equal to 150% of fan capacity, no recirculation was observed when the twin 75 kW fan location was at least 5 m and the twin 110 kW fan location was at least 10 m away from the dead-end crosscut access.

Oct 18, 2022

By L. A. Bertram, F. J. Zanner

"The goal of this paper is to present a tool to simulate transient melting of the electrode tip. This capability is needed to develop and test furnace control algorithms since experimental determination is difficult and expensive. Simulation incorporates parameters (including arc voltage, arc current, electrode gap and furnace pressure) from previous quasi steady experiments with 460 mm diameter Inconel 718 electrodes.Cathode heating rates (determined by classical as well as experimental arc models) are linked to these independent variables. After radiative loss adjustments to the heating, transient one dimensional melting is computed. IntroductionThe vacuum arc remelting (VAR) process attempts to improve the physical and chemical homogeneity of a static-cast electrode by remelting and solidification in a quasisteady manner. To achieve steadiness of furnace operation requires automatic controls based on inputs measuring physically relevant state variables of the process. Previous industrial scale VAR studies (1,2,3) involving stainless steels, superalloys, and other alloys have provided a basis on which control strategies of some generality can be proposed (4). Of these measurements, the data for Inconel 718 is the most complete, so discussion in this paper is restricted to this alloy.Studies of the In 718 alloy subjected to the VAR process have established that melt rate M (kg/hr) depends not only on the melt current 1m (kA) supplied to the furnace, but also on ambient gas pressure of CO, PCO (micron), and electrode gap ge (mm) as well (1):"

Jan 1, 1986

By G. M. Carr-Harris

"THE SUBJECT of permanent molding has received a great deal of attention in the technical press as illustrated by the many excellent articles in the bibliography which follows. In general, this covers the period 1940-1958 and is merely representative of what is available. Numbers in •brackets refer to items in the bibliography.It may be desirable at the outset to give a few definitions covering those terms directly related to this subject. The following is a definition of permanent-mold casting as given by J. W. Meier in a paper, ""The Non-Ferrous Metals and Alloys"", read before the Ottawa Valley Chapt.er of the American Society for Metals:""Permanent Mold Casting is used where a large number of castings of the same part are required and higher mechanical properties, greater density and closer tolerances are essential. Since metallic mold s are very expensive, the number of castings must be sufficient to, defray, at least partially, the added expense. Molds are usually made from a good quality cast iron, 1but other mold materials, such as the aluminum and copper alloys, graphite, ceramics, etc., are being used in certain cases. Important factors in permanent mold casting are the mold temperature; the proper mold dressing; and, as in all other casting methods, the mold geometry, that is to say, the design of spruces, gates, risers and vents""."

Jan 1, 1960