Search Documents

By David Oyler, Craig Compton

The The National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Research Laboratory (PRL) is continuing to investigate the behavior of fully grouted roof bolts in the weak roof rock of the Safety Research Coal Mine (SRCM). This paper describes the results of three studies: • A series of 24 pull tests of bolts installed fully grouted and overcored to leave 12 inches of grouted bolt. The tests compared the pull-out performance of offset-head roof bolts with that of standard 5/8-inch bolts; • A second series of 24 tests that compared the pull-out loads obtained by bolts installed with 1 ft of resin (a Short Encapsulation Pull Test or SEPT) to that of fully grouted bolts overcored to leave only 12 inches of grouted bolt, and; • An investigation into the pressures generated during the installation of fully grouted resin bolts. All of the bolts installed and pulled were overcored and removed from the roof after the pull tests to allow inspection of the resin. The first study found that there was no significant difference in pullout load between the offset-head bolts and the standard bolts. The second study, comparing the SEPT bolts and the partially-overcored fully grouted bolts, indicated that SEPT can significantly underestimate bolt anchorage grip factor, suggesting that the SEPT is a conservative measure of actual bolt performance. Significant loss of resin to cracks in the roof was observed in the bolts overcored in the SRCM. The third study explored one possible explanation for the resin loss, high pressures generated during bolt installation. These tests employed bolts installed in strain gauged steel tubes. The results confirmed that significant pressures (greater than 4,000 psi) can be generated during bolt installation. The results of the pressure tests, combined with the observations of resin loss in bolts installed in the SRCM, suggest that under some circumstances resin loss and under-encapsulation could take place and lead to degraded bolt performance. Glove fingering was observed in all recovered bolts to various degrees. The limited comparative data suggested that the effect of glove fingering ranged from slight to moderate. Complete mixing of the resin was observed on all of the 40 bolts recovered (28 fully grouted and 12 SEPT). Australian and U.S. resins were compared and the Australian resins were observed to have much smaller catalyst compartment areas and lower resin viscosities. These differences are suggested as potential explanations for occasional resin mixing problems noted in Australian resin bolt installations.

By Guillermo Lazcano Ríos, Jorge Parvez Aguirre, Alejandro G. Díaz Berríos, Felipe Rodriguez Alveal

Codelco's Chuquicamata Underground Division (DCHS) faces issues due to collapses in its subsidence streets, which hinders the advancement of the subsidence front and leads to the loss of areas and reserves. To address these issues, DCHS and Orica have developed a new excavation methodology based on pre-loading explosives in high drawbell. This methodology involves creating a high drawbell extending from the floor of the production level to the ceiling of the subsidence level, divided into two phases: upper and lower. A resin stemming is used to separate these phases. The excavation strategy adjusts to variables such as reception volume, fluffing, and excavation geometry, involving vertical pre-loading of the explosive and the use of a separating element between the phases. The test aims to validate the new excavation methodology and the retaining element in the rock mass, evaluating aspects such as drawbell geometry, impact on the rock mass, damage to the retaining element, and fragmentation. Wireless electronic detonators are used in the upper phase to improve safety by eliminating the need for physical connections, while traditional electronic detonators are employed in the lower phase. Low-density bulk emulsion is applied to minimize the impact on the Crown pillar and extraction point, and higher-density explosives are used above the subsidence level to ensure good caving. Results showed that the blast achieved 86% conformity with the theoretical design. Resin stemming allowed for 100% effective detonation in the upper columns, and the fragmentation obtained was 5.44 inches, which was less than expected. No damage to the Crown pillar was observed, and the explosive quality met standards. This technique has proven to be effective and viable, suggesting the possibility of eliminating the subsidence level in future levels, resulting in savings, and providing greater stability to the rock mass.

Jan 21, 2025

By Georg Petersen

El Perú es un país rico en diversidad de metales empleados en los campos de la minería, metalurgia, orfebrería y artesanía durante los tiempos pre-históricos. Dichos metales son: oro (objetos laminados por martilleo, repujados, pulidos, vaciados, soldados y dorados), plata (objetos trabajados de la misma manera que los de oro), cobre (objetos en diversas formas, como son discos, recipientes, herramientas y armas, en muchos casos dorados y/o plateados) y el azogue (cinabrio usado preferentemente para pintar las caras de los guerreros, las máscaras de los fardos funerarios y las caras de las mujeres nobles, costumbre que se generalizó a principios de la época colonial). De otro lado, existen otros cuatro metales que se emplearon en cantidades pequeñas como: fierro, platino, plomo, estaño.

Nov 1, 1970

The molecular structures of isobutyl xanthate (IBX), diisobutyl dithiophosphate (DIBDTP), O-isobutyl-N-ethyl thionocarbamate (IBETC), O-isobutyl-N-ethylcarbonyl thionocarbamate (IBECTC) and O-isobutyl-N-ethylcarbonyl thiourea (IBECTU) were fully optimized using density functional theory (DFT) at the B3LYP/6-31+G(d,p) level with the integral equation formalism for the polarizable continuum model (IEF-PCM) in the aqueous phases. The effects of the polar groups in these thiol molecules on their collecting performances were determined by the energies and compositions of frontier molecular orbitals and the atomic charge values. Our results indicate that the sulfur atom(s) in IBX, DIBDTP, IBETC, IBECTC, or IBECTU molecule is the centre of reactivity. And the collecting abilities of these reagents for copper sulfide minerals follow the order as: IBX > IBECTU ? DIBDTP ? IBECTC > IBETC, and the order of their selectivities against pyrite is suggested as: IBX < DIBDTP < IBETC < IBECTU < IBECTC. The theoretical analysis provides an insight into the collecting powers of these collectors, and offers an atomic scale approach to understand the experimental data available in the literature. Keywords:xanthate; dithiophosphinate; thionocarbamate; thiourea; density functional theory; structure-activity relationship; copper sulfide mineral

Feb 27, 2013

By Gordon E. Fletcher

This Bureau of Mines report outlines the atomic absorption analysis of oilfield brines for barium, calcium, copper, iron, lead lithium, magnesium, manganese, potassium, sodium, strontium, and zinc, using the method of additions. The advantages of using atomic absorption are discussed. The method of additions was chosen to overcome large matrix interferences usually found in brines; techniques of overcoming chemical, ionization, and background interferences are also described. The method was used to analyze several hundred oilfield brines and found to be rapid and reasonably accurate. A solvent extraction method was used to concentrate lead, copper, zinc, and iron in low-level samples.

Jan 1, 1974

By William F. Daly, William H. Hansmire

Installation of initial tunnel support is often the most uncertain element of work in the design of, and a contractor bidding on, construction of a rock tunnel. The risks the construction contractor and owner assume are delineated to a great extent in the technical specifications portion of the contract documents. It is intended that this paper identify current practices for specifying initial tunnel support and the impacts each case has on the assignment of risks associated with providing the initial tunnel support. Examples of recently completed tunnel designs are given.

Jan 1, 1985

By E. L. Gillenwater

Coal mine planning has three distinct decision levels: (1) decisions made at the upper level of management that determine production requirements for specific mines, (2) decisions made at the middle management level, the mine level, that determine how the mine satisfies its production requirements, and (3) decisions made at the operating level of management, the sectional level, that determine the sequencing of machine movements at the face. In this paper, the underground production scheduling problem is formulated in multi-stages using the Hierarchical Production Planning (HPP) approach. Two linear programming HPP models for accomplishing decisions at the first two levels are developed. Both models address the aggregate production planning process. The Mine Production Scheduling (MPS) model permits determination of monthly production and inventory levels. The Section Production Scheduling (SPS) model incorporates a quality blending requirement into the determination of weekly sectional production and inventory levels.

Jan 1, 1995

By Rongjie Kong, Shiwei Wang, Guomin Wei

Owing to the selective oxidation and uneven combustion that occur on the surface of carbon anode, some carbon particles detach and form carbon residue, which is defined as spent anode slag (SAS). The highly graphitized and toxic impurities such as fluorite ( CaF2), corundum (α-Al2O3), and cryolite ( NaAl11O17) are crucial components of SAS resource but are difficult to separate from graphite. This study developed a method of using water-soluble (emulsified) kerosene to separate the carbon particles from the toxic impurities in the SAS resource. The flotation purification approach of utilizing conventional kerosene was experimentally investigated and compared with that of using water-soluble kerosene. The results showed that with the use of emulsified kerosene, the maximum combustible matter recovery of the carbon particles was 89.86% while that of using traditional kerosene was 80.30%. The emulsified kerosene was comprehensively examined by various instruments to clarify its adsorption mechanism on the carbon particle surfaces. Because of the superior dispersibility of emulsified kerosene, it effectively envelops carbon particles with a smooth surface, oxygen-containing functional groups, and hydrophilic C–F bonds, thereby increasing the surface hydrophobicity and flotation responses of targeted carbon particles.

Feb 6, 2024

By Freeman Bishop

Having obviously cleared the way for fast confirmation by the Senate Interior Committee, the Administration recently named Elburt F. Osborn, vice president of Penn State University, as director of the Bureau of Mines. Interior Committee Chairman Henry M. Jackson (D of Wash.) has moved hearings on the nomination right along, forecasting that they will end in a confirmation. Dr. Osborn not only made a good impression on the Committee, he also made it amply clear that he would be the boss of his job and have right-hand aides to help straighten out conflicts stemming from recently enacted health and safety regulations for miners. Mining engineers in the field hope this clarification can come soon. They are frankly fed up with local, state, regional and national overlapping of restrictions.

Jan 1, 1970

By Emily Sing, Ashim Gajurel, Thomas Pennington, William Brown

The Pardee Chemical Feed Shaft Project involves construction of two new chemical feed shafts to improve raw water treatment capabilities at the East Bay Municipal Utility District’s (EBMUD) Pardee Reservoir in Valley Springs, California. The project includes construction of two 250-foot deep, 16-inch diameter stainless steel chemical feed shafts that penetrate an existing 8-foot diameter concrete lined conveyance tunnel. The design approach required the shafts be installed using top-down drilling methods and within a strict verticality tolerance (0.1%). Innovative precision drilling techniques ensured that the shafts penetrated the tunnel in their planned locations and the installed chemical feed lines would function as designed. Challenges included extremely limited access to the tunnel because of a requirement to maintain the tunnel in service during construction. This paper discusses the overall project’s design and construction approach, including unanticipated conditions that the project team faced and how these conditions were managed and overcome through collaboration between the contractor, designer, and owner.

Dec 1, 2022

By W. K. Hitchcock

Anecdotal evidence suggests that re-entering a sealed heating poses a significant hazard, whereby the original heating is rejuvenated at an accelerated rate forcing withdrawal and re-sealing of the area. Bulk-scale laboratory experiments using a two-metre column confirm these mine site observations. A high volatile bituminous coal from New South Wales, Australia was allowed to develop a significant hot spot before being inerted with nitrogen and allowed to cool. Air was then allowed back into the coal after the nitrogen was turned off and a hot spot developed almost immediately at the same location as the original hot spot before it quickly migrated towards the air source within a day. Two more re-entries were simulated. Each successive re-entry developed a broader hot spot and took longer to reach thermal runaway. These results clearly show the behaviour that can be expected when trying to recover a section of an underground coal mine that has been sealed due to a spontaneous combustion event.

Jan 1, 2009

By R. J. Thompson

Well-designed and maintained haul roads are the key to minimizing truck haulage onroad hazards and costs, as well as increasing productivity. In practice, however, designing and managing a haul road for optimal performance is often difficult to achieve, especially when resources assigned to design and construction are constrained. By understanding how a road design is developed from geometric, structural, functional and maintenance considerations and, critically, the interplay between these components in design and operation, optimal performance can be achieved. This paper briefly summarizes the evolution of mine haul road design, from the seminal USBM work of Kaufman and Ault in 1977, through to current geometric, structural, functional and maintenance management design components. These augmented design and management guidelines have been developed over the past decade, both in response to the requirements of mine operators for safer and more efficient haulage systems, the truck manufacturers’ requirements for a more predictable and controlled operating environment and the recognition of human factors as a significant contributor to haulage accidents. While the human factor is the most problematic to address in a road design, the paper shows that the more that is known about human error, the better a road can be designed to accommodate those actions or non-standard practices that would, on a poorly designed road, invariably escalate an error into an accident.

Jan 1, 2010

By AIME AIME

FREE competition, long the controlling ideal of domestic trade within the United States, has had the fundamental geographical advantage of functioning in the world&apos;s largest area of unrestricted commerce. Goods moved back and forth across state lines, unimpeded by customs, and industrial operations have developed rapidly to meet the expanding needs of a pioneer country richly endowed with natural resources. Fifty years ago, antitrust laws were adopted to protect the competitive private enterprise principle. It became illegal for one person to combine with another to restrain trade or commerce among the several states or with foreign nations. The original legislative measures defining this philosophy were the Sherman Act of 1890 and the Clay- ton Act passed in 1914. The development of Europe and other parts of the world was influenced by different conditions which led to a different theory of trade. Here were many small nations, with limited natural resources and a thin market, and they attempted to protect their national economy by tariff walls. International business arrangements for the purpose of diminishing the ups and downs of the more competitive system --crux of the modern cartel operations-seemed a logical device to stabilize production and guard the interests of both workers and consumers. European governments as well as European industrial interests became convinced that if com- petition could be held in bounds the danger of business depressions and un- employment could be reduced.

Jan 1, 1944

By Timothy W. Ellis

This paper presents the basic theory of operation, physical chemistry and phase equilibria which allow the development of liquid-liquid extraction circuits based on metallic solvents. The incorporation of reduction and reduction/diffusion processes into the process &apos;scheme is discussed and a detailed description of ,several liquid-liquid extraction schemes are developed. A synopsis of experimental results obtained using this: method to separate rare earth and other metal based materials will be given.

Jan 1, 1996

By A. E. M. Warner

In co Limited has long and extensive experience in converting nickel-copper primary smelting mattes over a broad range of nickel/copper weight ratios and combined nickel-copper-cobalt contents. At the Copper Cliff Smelter, the composition of the converter product matte has to meet the requirements of the matte separation process; at the Thompson Smelter, converter matte of a different composition is cast into anodes for nickel electrorefining; and in Soroako, Indonesia, a very low copper product matte is granulated for the Japanese market. Recently, Inco has conducted pilot plant testing of three possible nickel-copper matte continuous converting routes, namely flash converting, oxygen top blowing-nitrogen bottom stirring, and tuyere blowing. This test work has generated substantial new information on nickel-copper matte converting chemistry. This overview paper reviews the metallurgy of nickel-copper matte converting, in particular the behaviour of cobalt and the operating conditions required to meet the iron and sulfur specifications of the product matte. The relevant thermodynamic information is used to discuss the industrial data.

Jan 1, 2003

By D. E. Shanks

As part of its goal to help maintain an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines, U.S. Department of the Interior, is investigating a fused-salt electrolytic procedure for producing zinc metal. A previous report described preliminary, small-scale work on the fused-salt electrolysis of ZnC12. The present report covers a more detailed investigation of the properties of ZnC12-alkali metal chloride electrolyte systems in relation to the production of zinc metal and also discusses electrolysis in largescale, internally heated cells. The effect of composition on bath stability, current efficiency, cell voltage, and liquidus temperature was determined for the ZnCla-NaC1-KC1, ZnC12-NaC1-LiC1, and ZnC12-KC1-LiC1 electrolyte systems. An electrolyte com-posed of 38 mole-pct ZnC12, 31 mole-pct NaC1, and 31 mole-pct KC1 gave the best overall results. Sludge (ZnO) formation in the ZnC12-NaC1-KC1, ZnC12-KC1-LiC1, and ZnC12-KC1 systems was investigated during prolonged electrolysis. The ZnC12-KC1-NaC1 electrolyte showed the least sludge formation. A 1,500-amp cell was operated using the ZnC12-NaC1-KC1 electrolyte at 500° C. Zinc metal was produced at the rate of 4.0 lb/hr with a current efficiency of 95 pct.

Jan 1, 1979

Although out of the ordinary, MINING ENGINEERING is pleased to present a few photographs that typify Western US mining activity during WWII. The photographs, taken by R.G. Zellers at Colorado mining operations between 1942 and 1946, were primarily intended for equipment manufacturers. The pictures capture scenes of hardworking miners during a time when output was essential to fuel a wartime effort. In addition to providing a rare opportunity to step back 40 years and view the equipment and activity common at the time, Zellers&apos; skill with photo composition and his ability to obtain clarity in dimly lit underground operations gives viewers an acute awareness of the dampness and dirt of the mines, and a sense for the miners&apos; limited working space.

Jan 6, 1983

By Euclid P. Worden

In 1977, an article in World Mining (1) reported a total of 2726 rotary blast hole drills in service. This figure included only those machines produced by three of the manufacturers building drills of this type. The total, therefore, is much higher: Rotary drilling in the mining industry is big business to the manufacturers and suppliers involved, and a significant cost item, to mine operators. The time has come to take a hard look at rotary drilling technology with an eye to re¬ducing costs by increasing drilling efficiency. The efficiency of any rotary drilling operation is measured in terms of the rate of penetration achieved by the bit. In blast hole drilling, five factors affect the rate of penetration. They are: 1. Bit selection 2. Weight on the bit 3. Rotary speed 4. Hole cleaning 5. Formation properties Of these factors, all but one may be control¬led by the operator. Looking at any one in detail may reveal possible improvements in the system. Cleaning the hole is a good place to start. In order for a bit to perform at its maximum capability, each tooth or insert should strike fresh, clean rock as it falls into its drilling position. If the tooth or insert lands on previously drilled cuttings, a major portion of the energy delivered to the bit is absorbed in re drilling this broken material. A major portion of the interest, therefore, should be directed to the proper cleaning of the bottom of the hole.

Jan 1, 1979

By H. Copur

Experimental studies for quantification of force and brittleness indices relevant to rock cutting performance are presented. A simple interpretation method is developed, which quantifies the force-penetration response obtained from indentation tests. Basic parameters of the quantification are force increment and decrementrates, force increment and decrement periods, and number of increment and decrement data points. Blocks of eleven different rock samples were collected from different operating mines in Turkey and subjected to indentation tests to calculate the indices. The samples included harzburgite, serpentinite, trona, limestone, claystone, two different sandstone samples, siltstone and three different chromite ore samples. The concept was validated by a set of full-scale linear cutting tests using a conical cutter for measuring the cutting performance in relieved and unrelieved conditions, i.e. cutter forces, specific energy, size distribution of rock cuttings. The rock cuttings were sieved to determine coarseness index, indicates coarse chip generation characteristics, and size distribution. The force index is moderately correlated with the cutting performance and mechanical properties of the rocks, and poorly correlated with the coarseness index and size distribution of cuttings. A general and moderate trend is observed between the brittleness index and the coarseness index, cutting performance for unrelieved cutting conditions and mechanical properties of the rocks. However, additional data is required to fill the data gaps and to potentially establish relationship between the brittleness index and all other parameters.

Jan 1, 2003

By E. J. Wasp

An upsurge of interest in slurry pipelines to move coal from Wyoming, Montana, and Colorado to markets in the southwest, west, midwest and northwest has recently developed. Specific pipelines have been proposed to serve these markets; the routes of these lines are depicted in Exhibit I. It is, therefore, timely to discuss some technical aspects of the terminal facilities for these western coal pipelines. The discussion will be based on experience with the Ohio and Black Mesa pipelines as well as detailed planning and testing for a proposed 1,000-mile system from Wyoming to the middle south area. The economics of the pipeline terminal processes are heavily depend¬ent on site, type of process used, and other specifics of the situation. However, the following approximate breakdown of costs for a 1,000 mile, large capacity pipeline will be useful for orientation purposes. [Water supply 4 Coal cleaning 5 Feed preparation 10 Slurry transportation 72 Dewatering terminal 9 100%]

Jan 1, 1976