Search Documents

By G. Kugler, M. Tercelj

"The 1.2690 high alloyed tool steel is usually applied for cold working and is alloyed with carbide-forming elements Cr, V, W and Mo. It exhibits very poor hot deformability. Since there is no enough available data in literature for elucidation of this problem, hot workability and development of microstructure during hot deformation was studied. Hot compression tests were carried out in temperature range 850-1150 °C and strain rates range 0.001-6 s-1. SEM and OM were used for observation of microstructure. Results revealed very complex precipitation of carbides that depends on deformation temperature as well as on strain rate. It was found that especially at lower temperatures of hot working range the precipitation of carbides strongly depends on strain rate. Three different hot deformation behaviors’ were observed depending on temperature and strain rate range.IntroductionThe hot workability of highly alloyed high speed steels is usually described as relatively poor in comparison to other steels due to their tendency of cracking during hot working especially when inappropriate hot working conditions are applied. Alloying elements such as Cr, W, Mo and V in ledeburitic tool steels form carbides that improve hardenability, strength, hardness, wear resistance, etc., but they decrease hot workability and narrow hot working temperature range in comparison to conventional steels. The size, distribution, type and fraction of carbides, as well as the thermomechanical history of material and hot working parameters have major influence on the hot workability. The microstructure of ledeburitic tool steels during hot deformation can be characterized as a two-phase system consisting of an austenite matrix and a combination of ledeburitic carbides [1-4]. In the soft-annealed condition the total volume fraction of carbides is in the range 19-30% and in the quenched condition in the range 9-25%, depending on the chemical composition. During heating before deformation a large quantity of carbides dissolve, but non-dissolved carbides can have an extremely diverse influence on the hot workability due to variations in their composition, size, distribution, hardness and shape, and their different behavior during the deformation phase [5-7]."

Jan 1, 2011

By N. A. Beier, R. Amos, Smith. L., C. Atherton, D. R. Barsi, D. Blowes, D. C. Sego

"Waste rock is one of the most abundant materials at mine sites and must be properly characterized and managed to limit acid rock drainage and other harmful byproducts. An experimental waste rock pile—part of the test piles research program—located at the Diavik diamond mine (Northwest Territories, Canada) was deconstructed and sampled to study the spatial variability of material properties. Bulk samples were classified based on the amount of material finer than 4.75 mm. Hydraulic properties of each sample were estimated and particle size distribution analysis was completed. These datasets and classification methods might be used to improve the understanding of hydraulic and geochemical behaviour of the material and to study waste rock at other sites. ¦ KEYWORDS Acid rock drainage (ARD), Material classification, Particle size distribution (PSD), Waste rock RÉSUMÉ Les stériles font partie des matériaux les plus abondants sur les sites miniers et, en tant que tels, doivent être correctement caractérisés et gérés afin de limiter le drainage rocheux acide (DRA) et la pré¬sence d’autres sous-produits nocifs. Dans le cadre du programme Test Piles Research Program, un amas de roches stériles expérimental situé à la mine de diamant Diavik (Territoires du Nord-Ouest, Canada) a été décomposé et mis à l’essai afin d’étudier la variabilité spatiale des propriétés des matériaux. Les échan¬tillons en vrac ont été classés en fonction de la quantité de matériaux plus fins que 4,75 mm. Les propriétés hydrauliques de chaque échantillon ont été estimées et l’analyse de la composition granulométrique effectuée. Ces ensembles de données et méthodes de classement serviront à mieux comprendre le com¬portement hydraulique et géochimique du matériau et à étudier les stériles sur d’autres sites. ¦ MOTS CLÉS classement des matériaux, composition granulométrique, drainage rocheux acide (DRA), stérilesINTRODUCTION Statement of problem The characterization of mine waste rock remains a challenge in active mining sites. The large volume of material and the large size of particles make it difficult to collect representative samples. Sampling techniques are often dis-ruptive to mining operations because they alter the structure of the waste rock pile or interfere with mine traffic. The convention at most mine sites to collect little to no information on waste rock material means that models and predictions of how waste material will behave and interact with the surrounding environment are based on general information that might not be site specific. This could lead to environmental damage or higher costs if environmental effects are underestimated during the construction of waste rock structures."

Jan 1, 2019

By H. L. Hartman

The estimation of the magnitude of pressure changes which occur in mine ventilation circuits is of primary importance to the mining engineer in making changes in an existing mine or in projecting the ventilation requirements of a new mine. It is a formidable task in many cases, because no adequate theory is available and empirical data are unreliable or even lacking. The common practice of increasing one's estimate of the mine static pressure by an arbitrary "safety factor" to compensate for the unknown is a poor substitute for accuracy. Generally little difficulty is encountered in calculating friction losses in mine airways. As long as the friction factor can be reliably estimated, the well-known Atkinson formula gives accurate results. However, it is in the determination of shock losses that the ventilation engineer encounters difficulty and is apt to resort to an arbitrary allowance. Shock losses may constitute as little as five or as much as twenty-five percent or more of the overall pressure drop in the mine, and such allowances are generally completely unsatisfactory. Since other shock losses have been covered by McElroy (1), this paper deals with a long-neglected source of shock and pressure change in ventilation circuits, divergence and convergence of airflows, here referred to by their more common mining terms, splits and junctions. PREVIOUS WORK There is practically no fundamental information available in ventilation literature on the splitting and junction of airflows, either in mining or mechanical engineering periodicals or handbooks. Fluid mechanics textbooks seemingly avoid the subject of divergence and convergence, except for brief empirical treatment. The only investigation reported for mine ventilation systems was by Weeks, et a1 (21), in 1933. Although applicable to the case of line brattices in coal mines, it cannot be applied to the general case of mine splitting and junctions involving change of direction with little or no area change. In dealing briefly with the subject of shock losses at splits and junctions, McElroy (1) suggests only that they be considered comparable to bends, with losses at junctions being increased 50 pct to allow for interference of merging streams. He recognizes the importance of quantity ratio but concludes that exact quantitative data are lacking to compute losses at splits and junctions. A very capable summary and analysis of the state of knowledge in industrial ventilation and fluid mechanics regarding losses due to divergence has recently been reported by Gilman (3). In considering all earlier work dealing with both air and water as fluids, he compares results on a common basis and obtains good empirical agreement. For divergent flow, the controlling variable in each branch is the quantity ratio, although the deflection angle is of secondary importance. Empirical equations are presented for straight and 90-deg branches with varying velocity ratios, assuming branches smaller than the main duct. These formulas are modifications of the Borda equation for abrupt contraction and expansion. The only information available on shock losses in convergent flow are approximate experimental data presented by Alden (4) and the Manual of Recommended Practice for Industrial Ventilation of the American Conference of Governmental Industrial Hygienists. Alden considers the effects of both quantity ratio and deflection angle. The data indicate an effect opposite to that observed in divergence, the shock loss varying directly with quantity ratio. SHOCK LOSS THEORY Because pressure losses due to shock have been found to bear a constant relation to the mean velocity of flow in a given conduit, they are frequently expressed as a dimensionless function of the velocity head, termed the shock loss factor. For airflow in ducts and mine airways, the shock loss may be represented by the formula (1): Hx - XHv, (1)

Jan 1, 1961

By Richard Klimpel

The influence of selective chemical dispersants on the hydrocycloning of a copper ore slurry is illustrated. In the % solids and slurry feed rate ranges associated with industrial practice, desirable changes in both d50 and Sharpness Index values of classification were measured with the use of chemical as compared to tests with no chemical usage.

Jan 1, 1981

By L. R. Nelson

A review is presented of the furnace cooling system design and operating developments since the initial furnace start-up in January 2001 of the Chambishi DC-arc furnace to produce ferrocobalt alloy. The furnace operating conditions present a number of challenges to the furnace designers and operators, in particular, to provide a sustainable lining that can withstand the highly corrosive siliceous slag (roughly 50% SiO2). This is exacerbated by the dual requirement of operating this slag in a relatively highly superheated state (?T ?400°C when tapped at 1550°C) to ensure that the ferroalloy can be tapped (estimated 1370°C alloy liquidus temperature) prior to atomization. The core design challenge occurs at the alloy-slag interface, where a single refractory type cannot simultaneously meet the dual requirement of both adequate alloy and slag corrosion compatibility. Progression by the fourth furnace campaign to involve a retrofit of the bath sidewall to HATCH high-intensity, water-cooled, copper Waffle coolers and tap blocks is described. This involves operation of the entire slag bath, the slag-alloy interface and a portion of the alloy within a more chemically compatible refractory/slag (and possibly at times even an alloy) freeze-lining. Due to the high furnace power density employed (up to 500 kW/m2 hearth area), coupled with the large slag superheat needed, the resulting imposed peak bath sidewall heat fluxes are substantial, especially in the alloy (typically averaging 170 kW/m2), and on occasion have exceeded 1000 kW/m2. The performance of the HATCH Copper Waffle coolers under such aggressive process pyrometallurgical conditions is described. Aspects of the design and especially operating strategies to effect sustained production at up to 38 MW power input are also discussed.

Jan 1, 2004

By Vladimir G. Kochnev

"Autogenous and semi-autogenous grinding (AG and SAG) have been considered a step forward in comparison to conventional grinding circuits with several stages of crushing and using ball (and/or rod) grinding mills. However, existing AG and SAG technologies still can be improved and have an immense potential from the viewpoint of economic benefits.Experience gained by the Technics & Technologies of Disintegration Ltd. (TTD) in the research of grinding processes shows that comminution in AG and SAG mills can be performed in a more effective way. The company’s approach comprises the following elements:- Novel mill design- New liners and lifters- Novel discharge grid design- Technique of treating material of critical particle sizeA novel mill of the cantilever type capable to operate in the AG and SAG mode has been developed. The cantilevertype mill has a high diameter to length ratio, which dramatically increases the throughput rate, and is characterised by high reliability, fast installation and low capital and operating costs.Tests of the new heel-shaped liners, originally aimed at improving the intact condition of diamond, indicated that they play an important role in the grinding process. Tests performed by TTD jointly with ALROSA, MINTEK and Anglo-American Corporation, demonstrated that the heelshaped liners provided the increase in the throughput rate varying from 30 to 80 % and the decrease in power consumption in the range 30-55 % for grinding of kimberlite and platinum-containing ores.Investigation of the influence of the main grid parameters on the efficiency of grinding led TTD to a special design of a mill discharge grid, with a radial location of openings, the slot width varying from the periphery to the centre and the grid surface provided with “heels”. The design allows one to control the particle size distribution of the ground product without affecting the grid throughput rate."

Jan 1, 2003

A Good Product Range - So What! While in terms of water, waste management and environment protectrion, the Gippsland Basin may appear to have a good product range, what does this really mean? What it means is that, like any product range, the virtues of the product range must be sold and accepted by a majority of the public. The social, economic and environmental benefits of any enterprise using these products must be sold and accepted by the regional population. Many a budding entrepreneur has failed because he assumed that the public would accept his product, so good did it appear to be! However, we know that such an assumption must be avoided and that a great deal of time and effort needs to be invested in promoting and gaining acceptance of a product to ensure a long term and viable market.

Jan 1, 1992

By N. Bat, N. Sarantsatsral

Blasthole sampling practices were investigated at the Erdenet copper and molybdenum mine in Mongolia to address grade reconciliation issues. The goal of the study was to determine if the particle size distribution (PSD) of blasthole cuttings was accurately reflected in the samples. The study additionally examined if the measured grade was related to the particle size of samples. Using a sector sampler specifically designed to collect samples for the study, six large samples were collected from three blocks following a specialized protocol. Each sample was split into nine size fractions, ranging from larger than 12 mm to smaller than 63 µm. Copper and molybdenum grades were determined for each of the size fractions. For comparison, nine samples were collected from the same blocks following the standard mine sampling protocol. These samples were also split into the same nine size fractions. As with the other samples, grades were determined for each of the size fractions. The results showed that the PSD in the samples collected following the standard operating procedure varied significantly from sample to sample. This variation was much lower for the samples collected following the specialized protocol. Loss of fines was also indicated in the standard mine sampling process. These observations suggest that the standard sampling protocol did not consistently capture the PSD. The copper and molybdenum grades increased as particle size decreased, regardless of the sampling protocol used. This observation underscores the importance of the PSD of a sample being representative of the true PSD. Given the low number of samples in the study, it is not a strong conclusion that the standard sampling protocol captures the PSD inconsistently. However, it could be taken as a caution. On the other hand, the grade versus PSD relationship is more certain, given that it was observed regardless of the sampling method used.

Feb 1, 2017

By D. C. Oliver

Paper written on project work carried out in partial fulfilment of B.Sc. (Eng.) (Metallurgy and Materials) degree Corrosion in exhaust systems can occur on both the interior and exterior surfaces. Chloride-containing de-icing salts on the roads in colder countries greatly increases the rate of corrosion on the exterior surfaces. This paper investigates the relative exterior corrosion resistance of three alloys?two ferritic stainless steels( AISI Types 409 and 441) and an aluminized mild steel. The exhaust system is split into two categories?the hot end and the cold end. A test for each of these ends was designed?the standard ASTM G85test was modified to create a simulated driving cycle. The cold end test samples were exposed to ten driving cycles, and the hot end test samples were exposed to five driving cycles. A driving cycle constitutes the car being started from cold, driven until the operating temperatures are reached, and switched off and allowed to cool. Pitting corrosion is the primary corrosion mechanism occurring at the cold end of the exhaust system. The aluminized mild steel was the most resistant alloy in this test, and Type 409 the least. However, once the protective aluminium layer degrades, corrosion will occur rapidly. At the hot end of the exhaust system, spalling of the surface oxide layer is the primary corrosion mechanism occurring. Type 441 was the most resistant in this test, and the aluminized mild steel the least resistant. Potentiodynamic tests were performed on the alloys?the results agreed with the results obtained in the exposure tests.

Jan 1, 2003

By Michel Jébrak, Claude Bellehumeur

Abstract - Regional and orientation geochemical stream sediment surveys were carried out by the Quebec Department of Energy and Resources in southwestern Quebec, over a part of the Mont­ Laurier Terrane of the Grenville Province. The area contains some small stratiform zinc deposits. The response of Zn mineralization to geochemical surveys is weak; the known mineralization is not defined by anomalous samples and consistent patterns. This study uses a technique that increases the geochemical signature of Zn mineralization in filtering out geochemical background components related to lithologies and surficial conditions. The background variations were modelled using principal component analysis, and the filtering technique consists of the partial reconstruction of the data matrix from results of principal component analysis . The filtering procedure considerably enhances the Zn anomalies located in the catchment basins of Zn deposits, and defines some new anomalies in proximity to the marbles of the Mont-Laurier Terrane, the principal metallotect of Zn mineralization.

Jan 1, 1993

A method is proposed for the analysis of tin in cassiterite ores. Tin is volatilised by heating with ammonium iodide. The tin iodide so formed is extracted with hydrochloric acid and the concentration is measured by atomic absorption spectroscopy using an air-hydrogen flame.It is considered that a more efficient extraction of tin and faster reproducible results are obtained than by any other known method.

Jan 1, 1967

By D. Marcus

A methodology was developed wherein. the increase in compressive strength, mineralogical changes and pore water composition were all studied simultaneously as a function, of moisturized spent shale curing time. From these results the relationship between the nature of cementation process and the composition of pore water was established. Heavy metals were entrapped in the cementing constituents and the pore water became mainly a solution of alkaline sulfates. While the specific data are applicable only to the material studied, the methodology and general conclusions are useful for evaluating the environmental factors in spent shale disposal and expected leachates composition.

Jan 1, 1984

By Y. Ide, K. Kishitake

It is expected that an Al-Cr-N composite nitride film may have a higher resistance to oxidation at elevated temperatures than the well-known Ti-Al-N films. The formation conditions of Al-Cr-N films by a de reactive sputtering method and their properties were studied in this study. The films characterized with respect to their high temperature properties such as chemical composition, crystal structure, microhardness, wear and· friction. The crystal structure of the Al-Cr-N films changed from hexagonal phase to cubic phase with an increase in Cr content in the films. The resistivity to thermal oxidation of the Al-Cr-N films is superior to that of usual TI-Al-N films. A half of the friction coefficient in the Al-Cr-N film was obtained comparing with that in the ordinary TI-Al-N film at room temperature and the wear rate of Al-Cr-N film was 2 order smaller than that of TI-Al-N film. The Al-Cr-N films show a small friction coefficient at 500°C and then they are recognized to have good tribological characteristics.

Jan 1, 2000

By S. I. Sobol

Completeness of cobalt recovery from slag requires decomposition of maggemite and non - ferrous metal desorption with polymerized silicon-acid. Cobalt losses are reduced in leaching tai1s up to 200 g/t of iron.

Jan 1, 1993

By Paul I. Eimon

Mineral exploration involves the selective collection, organization, evaluation, and interpretation of geologic and economic data. The sources for such data are original field observations and existing documented information of various types (publications, reports, maps, company files, etc.). As exploration data are accumulated, their storage, organization, indexing, and J retrieval is key to exploration progress. Initial use of computers by mineral exploration groups indicates that data can be meaningfully handled by machines. A computer system makes possible: 1) the storage, manipulation, collation, and selective retrieval of data; 2) the utilization of data banks developed by geologic service groups and available at relatively low cost; and 3) the retrieval of stored data more rapidly, completely, and effectively than by manual systems. Profitable utilization of these capabilities is conditioned by several factors, particularly by the information selected for the system data base and by the design of the computer system itself.

Jan 1, 1968

By L Gobbo

X-ray diffraction (XRD) provides useful information about the composition of an ore sample in terms of quantification of crystalline phases and amorphous content. The use of new, fast detection systems implemented in CubiX FAST industrial diffractometers creates the opportunity to use this technique in exploration and modern process control. Besides the chemical composition of iron ores, their phase composition is also an important factor for exploration, quality control and processing. In the analysis of iron ore, XRD can identify the phases containing iron, such as haematite Fe2O3, magnetite Fe3O4, and goethite FeO(OH), and any other mineral phases present, especially silicas. Quantitative analysis is possible by various classical methods such as straight line or polynomial calibration with standards, but modern quantification analysis techniques such as Rietveld analysis or full pattern autoscale analysis are attractive alternatives, as they do not require any standards. These methods offer impressive accuracy and speed of analysis. Another analysis technique offering great benefit to ore exploration and process control is cluster analysis. This technique greatly simplifies the analysis of a large amount of data, eg from drill core samplings, and automatically sorts closely related scans of an experiment into separate clusters and marks the most representative scan of each cluster as well as outlying patterns. This can facilitate multi-dimensional compositional mapping of ore deposits, identifying regions of favourable mineral composition and allows fast and reliable tracking of the process. It is the most economic procedure to have automatic data evaluation without involving any dedicated personnel in the process. Details of the techniques used, sample optimisation methodologies, results, data precision and limitations will be discussed. The approaches have enormous potential as an inexpensive, reliable tool, useful in the characterisation of iron ore materials in an industrial environment.

Jan 1, 2009

By M. S. Celik

Despite its importance in various diverse industries, research on beneficiation strategies of boron minerals has not received enough attention. Boron minerals are primarily upgraded by wet processing methods. However, severe environmental constrains have accelerated the development of dry processing techniques such as calcination. Interestingly, boron minerals, colemanite, ulexite and borax undergo respectively decrepitation (fragmentation), shrinkage and expansion upon heat treatment. Each mineral then requires a different beneficiation scheme. In this study, laboratory and pilot plant studies on calcination of boron minerals conducted in our laboratories are reviewed along with their implications in commercial operations.

Jan 1, 1997

By W. E. Sabina

In the short period of one mans? career we have seen specifications for bulk material handling systems and equipment grow from two or three pages to as much as two or three volumes for a single contract. The old 'short form' described what the purchaser expected the equipment to do. The long form does the same but also includes nut, bolt, and lockwasher depth of detail. What are the events that led to this proliferation of verbiage, and does it benefit the buyer in the final analysis? Is there a better way to purchase complex equipment while ensuring the highest quality for the dollar spent?

Jan 1, 1986

By W. J. Schlitt

Introduction Heap and dump leaching are low-cost metal production techniques that are gaining in popularity among gold and copper producers. However, the flow of solution in heaps and dumps has received little attention in the literature. This is unfortunate since solution flow is one of the few parameters subject to operator control. Thus, solution management may well influence both operating costs and plant performance. Costs aside, there are two important aspects of solution flow to be considered -the metallurgical and the hydrological. Some of the metallurgical factors have recently been discussed (Jackson and Ream, 1980; Schlitt, 1984; Schlitt and Nicolai, 1987). These cover solution application rates and methods, irrigation rates, leach-rest cycles, and nonvertical solution flow. According to Caldwell and Moss (1985), however, the hydrological aspects may be more significant than the metallurgical ones. In particular, a phreatic surface will form when excessive flow leads to an accumulation of water and the associated buildup of pore pressure within the rock pile. Such internal flooding can either originate at the foundation or at some other zone of very low permeability. The latter condition gives rise to an impounded volume of solution, i.e., a perched water table (see Whiting, 1985). Caldwell and Moss point out that a rising zone of saturation is probably the most common cause of dump failures. Of course, such failures have even occurred in heaps that were carefully prepared for leaching (Milligan and Engelhardt, 1984). Thus, flooded conditions and perched water tables represent an important safety consideration as well as having an impact on metallurgical performance. The following sections describe a case history in which a perched water table developed within a copper leach dump. The description includes background information, solution flow rates, and metallurgical data. Then this situation is compared to one involving normal drainage. Description of the leach system The leach dump in the case history is located at a shutdown open pit copper mine. It was built in two lifts, with the second added some 20 years after the first. There is little detailed information available on the initial lift. It was built with rail¬hauled waste and was generally less than 30 m (100 ft) high at the crest. The area available for leaching was about 120 m (400 ft) wide and more than 380 m (1250 ft) long. The dump surface was prepared for leaching by dozing ponds approximately 12 m by 12 m by 2.5 to 3.0 m deep (40 ft by 40 ft by 8 to 10 ft). The ponds were leached by flooding with barren leach solution returned from a scrap iron cementation plant. Based on mill feed at the time, the average waste grade was probably close to 0.4% Cu. The first lift leached well. It accepted high flows, which together with the waste grade, produced a rich pregnant leach solution (PLS). Old records indicate a PLS of "50 lb Cu/ 1000 gal," or about 6 g/L. As later drilling would indicate, such a high tenor led to dissolution of considerable scrap iron that was returned to the dump. The iron then hydrolyzed and settled out on the pond bottoms. In addition, the waste settled substantially so that the unleached crest was 3.0 to 4.5 m (10 to 15 ft) above the ponded area. Eventually, the leachable copper was extracted and the dump became less permeable. Thus, the PLS tenor dropped until it became uneconomical. About ten years later, mining resumed and the decision was made to add another lift to the dump. This was done without giving much thought to a subsequent leach operation. Hence a 24-m (80-ft) lift was built on top of the original dump. The surface of the latter was not prepared in any way, e.g., by leveling and/or deep ripping, prior to over-dumping. Examination of subsequent drill cuttings indicated that the new lift contained about 0.2% Cu, with chalcopyrite and chalcocite (50:50) being the predominant copper minerals. Most of the chalcocite occurred as rimming on the abundant pyrite, with the pyrite to chalcopyrite ratio estimated at 10 to 1. The use of 100- and 120-ton trucks for haulage caused some waste compaction during emplacement. In addition, the host rock itself was relatively soft, being a porphyry intrusive material that was partially altered to clay. As a result of the initial compaction and clay swelling, the rate of water percolation from the new leach ponds was slow and the ponds often contained considerable standing water. Even frequent ripping failed to provide a sustained improvement in the percolation rate. The poor surface permeability was exacerbated by hydrolysis of iron salts which settled as a layer on the pond bottoms. Partly as a result of the permeability problems, metallurgical performance was not up to expectations. These had been based on laboratory tests which showed about 20% copper solubilization in two weeks. Continued copper extraction in the tests also suggested that a substantial percentage of the copper would eventually be recovered. However, the PLS grade in the actual operation peaked briefly at about 0.48 g/L Cu (4 lb Cu/1000 gal), then declined to a range of only 0.24 to 0.36 g/L Cu (2 to 3 lb Cu/1000 gal). The poor leaching was traced to a lack of oxidation of the sulfides. There were two principal observations supporting this conclusion. First, there was no evidence of any heat being generated within the dump. As discussed elsewhere (Schlitt and Jackson, 1981; Hiskey and Schlitt, 1982), pyrite oxidation is quite exothermic and the high pyrite content of the waste should have led to an increase in the temperature of the leach solution as it percolated through the rock pile. Second, there was no sign of any natural convective air flow through the dump.

Jan 1, 1987

By Thomas B. Douglas

INSTRUMENTATION in the process industries can no longer be regarded as a convenience, but rather an absolute necessity. Although many chemical processes must already be conducted with instruments, every properly designed application of automatic process control will improve operation: 1) the product will be more uniform and of higher quality; 2) the manual labor saved will reduce cost; 3) uniformity of flow and uniform control of process will increase production; and 4) surges will be eliminated, making it possible to operate equipment near ultimate capacity at all times. Industrial instruments fall into two general classifications—those that measure and those that measure and control. The cement industry has been using instruments for a number of years, particularly in the burning process, primarily for indicatlng and recording. Automatic process control makes additional use of these instruments, and others, to control variables. Assisted by the instrument manufacturers, engineers at Ideal Cement Co. achieved considerable progress in determining how well the usual recording instruments could be made to control various phases of cement-making. The results of these experiments were used to make the new plant at Houston as wholly automatic as possible. The original Houston plant, built in 1937 by Gulf Portland Cement Co., consisted of only one 8 x 220-ft kiln and the necessary grinding mills and accessory equipment and had a capacity of 900 bbl per day (300,000 bbl annually). Ideal Cement Co. purchased this plant in 1940 and almost immediately started plans to increase its production. In 1941 a 9 x 220-ft kiln was installed and grinding and storage capacity were increased. The growing demand for cement in the Houston area necessitated a third kiln (9 ft 6 in. x 250 ft) in 1947. This brought the plant up to its present capacity of about 1.3 million bbl per year. Calcium silicates in cement are produced in a burning operation at high temperatures from raw mix of argillaceous and calcareous materials that have been crushed, mixed, and ground to a fine powder. The composition of this mixture must be kept consistent within narrow limits. Raw mixing and grinding may be done either wet or dry, but in both instances the materials must be correctly proportioned, finely ground, and thoroughly intermixed before entering the kiln. As the raw mix passes through a long horizontal rotary

Jan 1, 1959