Search Documents

By G. P. Conard, R. C. Hall, J. F. Libsch

The 50 pct Fe-50 pct Co alloy undergoes a transformation from disorder to an ordered structure of the CsCl type reportedly in the vicinity of 732OC. During this process, the coercive force goes through a maximum, apparently as a result of strains associated with the coherent nucleation and growth reaction. This magnetic alloy also shows a marked increase in the ratio of residual to saturation induction, which is associated with annealing to a high degree of order with the continuous application of a magnetic field. The increase in ratio can be explained on the basis of a decrease in 90' domain boundaries and, perhaps, by an increase in anisotropy resulting from lattice distortion. THE 50 pct Fe-50 pct Co alloy undergoes a disorder-order transformation which has been reported to occur in the vicinity of 732°C1,2 The ordered structure is the CsCl type.' This magnetic alloy also shows a marked increase in the ratio of residual to saturation induction as a result of heat treatment in a magnetic field, sometimes called a response to magnetic anneal.'-' The purpose of this investigation was to study the course of the ordering reaction, the nature of the response to .heat treatment in a magnetic field, and the relation, if any, between ordering and the response. Procedure The method of approach in this investigation was to produce an initial structure as completely disordered as possible and then gradually to order the alloy by isothermal anneals at various temperatures under different conditions of the applied magnetic field. Magnetic, magnetostriction, and X-ray analyses were of primary importance in determining the property and structural changes resulting from the isothermal anneals. Rings of the 50 pct Fe-50 pct Co alloy were prepared from the elemental powders by a powder metallurgy technique, further details of which may be found in ref. 7. The initial structure was produced by annealing the specimens for ½ hr at 1000°C, cooling to and holding for ½ hr at 900°C (in the a range above the ordering temperature), and water quenching. Isothermal anneals were performed at 600°, 675°, 720°, and 740°C. For example, rings were heated to 600°C, held for a predetermined period of time, and cooled by natural cooling at a rate slightly slower than an air cool (average of 20" to 25°C per min). The tests (magnetic, etc.) were made after each heat treatment. All high temperature treatments were performed in a purified hydrogen atmosphere. The treatments at the various temperatures were carried out under one or more conditions of an applied field including 1—no field, 2—field of 20 oersteds applied on cooling only, and 3—field of 20 oersteds applied continuously during heating, holding, and cooling. Magnetic measurements were made using the standard Rowland ring technique8 with a maximum field strength of 100 oersteds. The magnetization curve, induction at 100 oersteds (B.), residual induction (Bt), and coercive force (Hc) were determined. All magnetic analysis data were based on an average of the results from three rings. A strain gage technique9 as used for the measurement of magnetostriction. The X-ray determination of the relative amount of ordered phase present was made on the ring specimen used for magnetic measurement. This was done by the back-reflection method using a rotating specimen (because of the large grain size) with unfiltered CoKa radiation and a 7 hr exposure time. Intensity measurements of the ordered line (300) were made by comparing visually the films so obtained with standard films prepared by exposing for different lengths of time a specimen given a long time anneal (high degree of order). Results In all instances the saturation induction (induction at 100 oersteds) was found to increase slightly with annealing time. This effect was small and appears to be the increase in saturation induction to be expected on ordering.10-13 The residual induction behavior was markedly influenced by the field condition during annealing, Figs. 1, 2. For the condition of no applied field, the ratio of residual to saturation induction remained essentially constant for short annealing times but showed a significant increase at longer times. With increasing annealing temperature, less time was required to produce this increase in the ratio. In the case of the 600°C anneals, the increase did not occur until approximately 20 hr, Fig. I, while on annealing at 740°C the increase was immediate, Fig. 2. Slight decreases in the ratio may be observed at 100 hr for specimens treated at 720°C and at 1 hr for those treated at 740°C. Specimens annealed in a field of 20 oersteds showed a residual to saturation induction ratio consistently higher than that for the specimens annealed without the field. The first anneal with the field (¼ hr) caused an abrupt increase in the ratio at all temperatures; thereafter, the increase in the ratio was generally similar for specimens annealed

Jan 1, 1956

The Southwest Pacific is a region of active volcanism and geothermal systems. Only in New Zealand have the geothermal systems been exploited for electricity generation and industrial processing. At present, approximately 280 MWe of geothermal electricity is generated in New Zealand. A considerable amount of further exploration work is required before the total geothermal potential of the region can be assessed and before the significance of these resources can be judged against other local energy sources.

Jan 1, 1990

By Juan Carlos Gentina

La biolixiviación de minerales es un proceso metalúrgico que permite el tratamiento de sulfuros insolubles y óxidos insolubles y ofrece beneficios económicos, ambientales y tecnológicos. En ese sentido, el presente texto señala un panorama de biominería y minería de cobre, la influencia de las variables operacionables más relevantes y su situación actual y presente en Chile.

Dec 1, 2013

By Clément F. Bernier

One of the chief sources of the world's supply of asbestos lies in a belt of ultrabasic rocks which runs northeastward through an area called the Eastern Townships, south of the St. Lawrence River in the Province of Québec. The productive portion of this belt extends from the town of Asbestos in the south, for a distance of some 9,5 km to beyond the village of East-Broughton. The first discovery of asbestos in this region was made in 1874. Only crude fibre was produced until 1888 when the first mill was erected near the town of Black Lake. Since the inception of the industry, almost 100 years ago, no less than 100 different compa¬nies have been formed and 46 different mines have been operated. There are presently 5 active companies in the area providing direct employment for 4100 workers, down from 6000 during the seventies.

Jan 1, 1984

By Ricardo Ponce

In recent years, ENAMI implemented modernisation plans at its two smelters in order to meet the government's environmental regulations introduced in the early 1990s. The modernisation plans defined the new SO2 and particulates emission targets, deadlines for compliance, and the revised treatment capacities of the smelters. At Las Ventanas smelter, the principal process change consisted of eliminating the reverberatory furnace. All the smelter feed is currently processed in a 4m diameter, 14m long Teniente Converter, using up to 34% oxygen enriched air. Dry concentrate is injected into the bath through tuyeres. A fuel oil burner compensates for any process heat deficiency. The Teniente Converter high copper content slag is cleaned in an electric furnace. This furnace is also used to melt internal reverts. This paper will discuss the successful operation of the slag cleaning electric furnace.

Jan 1, 1999

By Basak Anameric

This study reports preliminary feasibility investigations for utilization of the selective carbothermic reduction and smelting (SCRS) processing scheme to beneficiate low-grade iron-manganese (Fe-Mn) mineral deposits from MN, USA. The study includes laboratory-scale demonstrations using an induction furnace and production of various products by manipulation of operational parameters. The products include alternative iron (Alt Fe), high carbon ferromanganese (HC FeMn), alternative silicomanganese (Alt SiMn), and upgraded manganese concentrate (Mn conc). All of these products have commercial value and can be used in various applications as raw materials.

Nov 23, 2020

By Walford S. Wright, NORMAN EBBLEY

During the past decade (1937 to 1947), including the war years of heavy demand for metals, the United States realized about one-eighth of its antimony requirements from domestic production, chiefly in Alaska. In World War II, our foreign supply sources became endangered; and uncertainty in our Far Eastern supply made this nation focus on Alaska’s mineral resources with a Production Gear that centered in the Bureau of Mines experimental station at College (Alaska). The development work known as District or central deposits. The strategic mining districts included that of central Alaska was reorganized at Ketchikan Mining Districts. Mines were located here had produced considerable quantities since 1901; but methods for exploration had come from 1936 to spring 1942, some $4 million produced in gold alone. Statistics relating to available ores are those selected by type and exploitation periods with wide variety applied. During the summer of 1941, as part of an extensive Geological Survey program continuing through funds provided by U.S., geological surveys spent six weeks mapping an area approximately two square miles surrounding mines. The mines working both surface & underground work employed these men in mapping exercises.

Jan 1, 1948

By O. R. Swendseid

The Mountain Con mine is a relatively old, deep mine located in Butte, Montana. Operations at this property through the present shaft were started before the turn of the century. As mining progressed to depth, increasing demand for ventilation facilities and changing mining conditions made it convenient to convert some nearby shafts to airways. The fact that these openings had not been originally planned for use as airways made it necessary in some instances to utilize long and inefficient already-estab¬lished entries to service working areas. This situation existed in the Lexington fresh air system. The Lexington system consists of a vertical, 3-compartment shaft extending from surface to the 3200 level and a series of 2-compartment air raises and old horizontal-haulage openings extending into a mining area several thousand feet west of the Lexington shaft between the 3900 level and the 4200 level. Because of restrictions and high resistance in the portion of the system between the bottom of the Lexington shaft on the 3200 and the mining area on the 3900, the capacity of this system is only 85,000 cubic feet of air per minute. It was calculated that the capacity of the system could be in¬creased to meet the demands of the current mining program in this section of the mine by utilizing a single, straight, horizontal air course on the 3200 and by driving an inclined air raise 740 feet long between the 3900 and the 3200.

Jan 1, 1967

By Sharpin P. C

The countercurrent gas-solid heat transfer during the drying of brown coal briquettes in the pilot carbonization plant at Morwell has been analysed and theoretical gas and solid temperature distributions through the drier have been calculated. Although the calculations rest on several simplifying assumptions, the theoretical temperature distributions compare well with those observed in practical operation. Valuable conclusions are reached as to the effects of changes in drier operating conditions on the rate of drying of the briquettes which controls the strength of the char produced. The analysis shows why a limitation was reached in the improvement of char strength in the pilot plant in 1961 due to the performance of the drier and a prediction is made of a way in which the limitation could be overcome.

Jan 1, 1966

Application of the Anaconda Simplified Work Index for Multiple Test Sizes Vale uses Bond Work Index measurements extensively in a number of applications. The Bond Work Index is usually a good parameter for checking scale up procedures when sizing ball mills, as well as the basis for variability analysis whenever drill core data is available. It is typical to measure between 100 and 150 Bond Work Indexes, depending on the deposit characteristics. The Bond procedure is relatively complex and time costly. It also requires relatively large amounts of sample, which are very expensive to be obtained. The benefits of the Anaconda simplified procedure are: considerably smaller sample requirements and laboratory time. This makes it very much attractive at Vale's development centre, including geometallurgical mapping, operation efficiency control, mine to mill, etc. The Anaconda simplified procedure was implemented and evaluated at Vale's Development Centre using a number of ores and several samples of each ore totalling more than 190 measurements. The Anaconda simplified method was calibrated for several test sieves and a correlation for any test size was determined for Vale's test mill. The calibration was also extended for two sample top sizes. The relative error of the simplified procedure was found to be in the range of nine per cent which is within the expected error Bond standard procedure. The implementation of the Anaconda method at Vale's development center has been used with great success over the past years in several green field, brown field projects and operating plants.

Sep 13, 2010

By Jinke Li, Fenghua Wang

"While coal fueling China's economic growth it has already been causing severe pollution and amounts of CO2 emission. How to make deep reductions in carbon emission is not only a huge challenge for the greatest consumer of coal, but also a revolution for China’s coal industry. The paper explores how to shrink CO2 emissions during the lifetime of coal. The paper points out that increase of coal mine efficiency and productivity, green mining, utilization of coal mine methane and environment-friendly disposal of coal gangue can reduce CO2 during coal mining; coal preparation and coal by wire can decrease CO2 during coal preparation and transportation; improving combustion efficiency, CO2 capture and storage (CCS) and coal transformation can lessen CO2 during coal utilization. The paper also points out that Circular Economy Park is a practical way to develop a low carbon economy for coal industry. An econometric model for total coal industry and each sector are constructed to measure carbon emissions based on CO2 equivalent emissions, then with detailed calculations, based on potential greenhouse-gas emission's reduction, a most likely low carbon roadmap of China's coal industry is depicted with scenario analysis method.Introduction Global warming poses a profound threat to humanity and the natural world and is one of the most serious challenges humankind has ever faced. According to the 2007 Fourth Assessment Report by the Intergovernmental Panel on Climate Change (IPCC), global surface temperature increased 273.89 ± 273.33K during the 20th century (IPCC 2007). Increasing concentrations of greenhouse gases have caused most of the observed temperature increase since the middle of the 20th century (United States National Academy of Sciences 2008), and CO2 is the most important cause of global warming. In 2005, CO2 contributed 76% of global greenhouse gas emissions, CH4 contributed approximately 16%, N2O contributed approximately 6% and the combined F-gases contributed approximately 2% (IEA 2010). Among the many human activities that produce greenhouse gases, energy use is by far the largest source of emissions. Since 1870, CO2 emissions from fuel combustion have risen exponentially (IEA 2009). Of the three types of fossil fuels - coal, natural gas and petroleum - coal constituted only a quarter of the world total primary energy consumption in 2007. The situation is even more critical in China than in the rest of the world, as energy-intensive industrial production is growing rapidly, and large coal reserves exist in combination with limited reserves of other energy sources. The development and production of the coal industry provide stability in China's economic growth. There are more than 7000 coal enterprises in China; the coal enterprises are the main contributor to China's ""economic miracle""."

Jan 1, 2017

The simple act of taking a sample implies that someone will use the information contained in the analytical result to make a decision about a course of action. In the mining industry, the decisions may involve huge capital commitments for opening or closing a mine, or marginal tactical costs that involve deciding if a truckload of mineralized rock should be sent to the mill for processing, or the waste dump. Sampling is among the most fundamental activities in a mining operation, and this paper aims to examine some of the technical issues that can assist in ensuring that samples are representative and correct. Insights into the scale of variability require that we disaggregate sampling variance into its component parts and evaluate each one individually. The work of Pierre Gy in understanding the different sampling errors is the first step in establishing an optimal protocol. This must be followed by the appropriate measures to ensure the protocol is implemented such that minimal bias is introduced in the sampling process. Even with these insights the possibility exists for large unseen and hidden costs can accumulate in a mineral development because of sampling errors. These hidden costs arise due to misunderstanding of the principle factors that affect the size of sampling errors, such as the mass of the sample, the effects of splitting a sample to reduce the mass, and the influence of the nominal particle size. The handling of sample material without due regard to the sampling characteristics of the material being sampled is also a major source of sampling errors. The most significant problem is due to the influence of the so-called volume-variance effect. This effect is a consequence of the support effect and the information effect both of which relate to the difference in size at which samples are collected and mining blocks are extracted. The information effect is a function of the availability of data at the time that decisions are made about the destinations of mineralized rock, namely the mill or the waste dump. Implementation of appropriate sampling protocols in the mineral value chain remains a challenge throughout the industry. The growing understanding and deepening appreciation of sampling theory and methods means we stand on the threshold of a new era for implementing and understanding appropriate sampling procedures and protocols. In the interests of optimal development of the national patrimony it is suggested that standardization through the identification of structural problems and continuous improvement of mining processes be instituted at a national level.

Jan 1, 2007

By F. Michael Hosking

Modeling of a furnace brazing process is described. The computational tools predict the thermal response of loaded hardware in a hydrogen brazing furnace to programmed furnace profiles. Experiments were conducted to validate the model and resolve computational uncertainties. The results from selected furnace simulations and measured thermal events were compared. Critical boundary conditions that affect materials and processing response to the furnace environment were determined. "Global" and local issues (i.e., at the furnace/hardware and joint levels, respectively) are discussed. The ability to accurately simulate and control furnace conditions is examined.

Jan 1, 1998

By S. D. Zhang

The first reinforced earth railway bridge abutment in China has been successfully constructed of September, 1985 under the supervision of the Reinforced Earth Researth Group of Shanghai Institute of Railway Technology. In order to verify the reliability of the designed structure and its behaviuors, the 1:10 reduced scale model tests in laboratory and field tests on the actual structure during construction were proceeded. Various loads of different positions were charged, the vertical and lateral earth pressure in the filling soil, the stresses developed in the reinforcements, and the deformations of the models or the actual structure were recorded in those tests. The behaviors recorded are presented and discussed in this paper.

Jan 1, 2010

By B. K. Parekh

Silicon carbide (SiC) can be produced by heating rice hulls to elevated temperature, The product is a mixture of beta crystalline silicon carbide whiskers, particles and unreacted carbon. The silicon carbide whiskers are 0.5 micron in diameter and 50 to 100 micron in length and have been found useful for reinforcing metal and other composite materials. The carbon can be removed by combustion, but this makes separation of the silicon carbide whiskers from particles difficult and a high grade whisker product cannot be made. However, a clean high grade Sic whiskers product can be obtained from the pre-burned converted rice hulls using physical separation processes that are based on differential wetting. Recovery of Sic whiskers from the pre-burned material was found to exceed 90 percent. A modification of the froth flotation process developed during this study is now being used commercially to separate silicon carbide whiskers and particles and to recover a high grade whisker product.

Jan 1, 1985

By Bruce Cavender

Historically, the processing function has been regarded as efficiently managed as long as production costs were kept low, recovery was adequate and sufficient plant capacity was avail-able. In this paradigm, processing is viewed as capable of making only a limited contribution to a company?s competitive advantage. However, the processing function can provide a primary vehicle for building critical competitive capabilities. Processing organizations should be encouraged to become so accomplished they generate new opportunities for other functional groups and thereby influence a company?s overall strategy. This requires a deep shift in processing?s role, in its self-image and in the expectations of it held by managers in other functions. Specific plant improvement techniques ? total productive maintenance (TPM), loss control, etc. ? should be viewed primarily as means for building strategically valuable processing capabilities. Different improvement strategies create different kinds of capabilities and present new strategic options. Broadly speaking, a mineral-producing company seeks competitive advantage through two principal activities: the development of new mineral production and reserves and the optimization of existing operations. These lead to increases in ore reserves, production levels and cash flows that are manifested in increased profitability and, hopefully, increases in the price of the firm?s stock. The profitability of a minerals company is a function of the overall profitability of the industry sector in which the company participates and the firm?s competitive position within that sector relative to those of its competitors. Competitive advantage within the industry comes from two sources: the ability to maintain lower prices than competitors for the same product (cost leadership), or from the sale of products with unique properties that justify higher prices (product differentiation; Porter, 1980). Most mineral companies produce fungible commodities that are sold to anonymous customers, and sustainable cost advantage is the only long-run strategy available to these companies to enhance profitability.

Jan 1, 2008

By David J. Brown

Extensive deposits of bituminous, subbituminous, and lignite coals occur in the western United States (Figure 1). Over one trillion tons of identified resources have been located and inferred by geologists and more than 200 million tons of western coal are mined annually (1). In the future, production of western coals will increase significantly and approach national production levels of higher-rank eastern coals. Western coals will be utilized in new power plants as a replacement fuel for oil and gas and may be used in advanced technologies such as diesel engines or in direct-fired turbines. Since these applications require low-ash, low-sulfur coals, crushing to fine sizes and significant cleaning to remove minerals and sulfur will be required. Coal cleaning traditionally has been associated with reducing pyrite and other mineral matter from high-rank eastern coals. To date, insignificant quantities of western coals have been cleaned before utilization and limited data on their washability characteristics exist. Because of this lack of data, it is difficult to predict how these coals will react to standard washing techniques.

Jan 1, 1985

By Duan Xin-hui, Wang Xin, Peng Jin-hui, C. Srinivasakannan, Zhang Li-bo

The work attempts to optimize the process of preparation of modified semi-coke from semi-coke using phosphoric acid (H3P04) as the activating agent using the response surface methodology (RSM). The influences of three major dependent variables, the impregnation ratio, activation time, and activation temperature were assessed on the independent variables yield and the iodine number. The empirical relationship between the dependent and the independent variables were established using the quadratic response surface models, which were utilized to optimize the process parameters. The significance of each of the parameters and interaction among the parameters on the independent variable was assessed based on analysis of variance (ANOVA). The process variables were varied within the range of impregnation ratio (IR) from 1.5 to 4, activation time from 30 to 90 min and activation temperature from 550 'C to 650 'C. The optimized process conditions were estimated to be an IR of 2.29, activation time of 32 min, and an activation temperature of 605°C respectively using the process optimization tool. The BET surface area of modified semi-coke of the optimized sample was estimated to be 915m2/g, with the pore volume of0.71cm3/g, with an average pore diameter of 3.09 nm, with micropore volume fraction being 52.36%. The scanning electron microscope (SEM) images were utilized to visualize the surface pore structure.

Jan 1, 2013

By T. W. Eddy

Research was conducted in which elemental mercury and its sulfide mineral (cinnabar) are removed from a copper sulfide concentrate by low temperature thermal applications. The goal of this research was to reduce, volatilize, and collect mercury vapor from concentrated smelter feed in a simulated drying environment while maintaining the chemical integrity of the residual. The study used synthesized concentrates composed of copper sulfide and mercury bearing minerals (such as cinnabar (HgS) or elemental mercury) to determine optimal residence times and temperature ranges.

Jan 1, 1996

By David B. Reger

New discoveries of gas in the southern counties featured the petroleum industry in West Virginia during 194;. Drilling for oil increased slightly over 1944 and a small increase of initial production resulted. Out of 28 wildcats drilled, there were 16 gas discoveries and 12 dry holes. No commercial oil was found in the 28 wells.

Jan 1, 1946