Search Documents

By Y. Ren, B. Yang

The magnetic field characteristics due to electromagnetic stirring in the secondary cooling zone of an extra-thick slab during continuous casting are numerically determined using Maxwell's equations, with particular emphasis on the distribution of magnetic induction intensity and electromagnetic force, as well as the influence of process parameters on the magnetic field. The orientation of the electromagnetic force is the same when the electromagnetic stirrers at the 30° and 60° posistions of the arc-shaped slab are powered in the same direction; otherwise, the orientation is opposite. The magnetic induction at the centre of the section of the stirrer's central axis at the 30° positio, as well as the current, frequency, and fitting formulae, are as follows: B = {0.075I.(1/A)-0.3} mT and B = {-1.75f.(1/Hz)+22} mT. The electromagnetic force and current fitting formula at the central point of the B-B section is F = {0.03168I2.(1/A2)-03.762I.(1/A)+326.7} N/m3, and the fitting formula of electromagnetic force and frequency at the centre point is divided into two segments. The first takes the form of a parabola: = {-21((f-4.3).(1/Hz)2)+970} N/m3, and the second segment is negative linear: F = {-1.65f.(1/Hz)+51.5} N/m3.

Apr 16, 2024

By R. H. Smith, A. C. Polk

The physical properties of the materials are listed, together with a short explanation of how this material binds the sand grains together without materially reducing the effective permeability of the sand. The chemical can be used in wells with bottom-hole temperatures ranging from 105°F to more than 350°F A description of the equipment required and the techniques used for applying these plastics to the wells is included. Introduction Recovering oil and gas from unconsoli-dated sand formations offers one of the most troublesome of all production problems. These sands generally present no particular trouble while drilling is in progress, but after the well has been completed and a pressure differential has been established across the face of the producing zone, the formation begins to L'slough," resulting in "sanding up" of the well. The term "sanding up" means that sufficient volumes of sand have moved into the well bore or casing to cause a serious reduction or complete halt of all flow of oil, water or gas. In rare cases a well may produce only a small amount of sand and still continue to flow or pump, the sand being carried to the surface in the fluid stream. However, in such instances, the result may be a costly repair bill due to the effect of the sand on surface and pumping equipment. The difficulty of producing petroleum from sands that are loosely cemented has long been recognized by petroleum engineers but only within the last few years has any new approach to the problem been undertaken. This involves the use of plastics that are capable of bonding the individual sand grains in place without materially reducing the effective permeability of a formation. The successful application of plastics for the consolidation of poorly cemented sands is relatively recent but now it is widely used in many of the more difficult areas on the Gulf Coast of Texas and Louisiana. This relatively new use of plastics1 in the oil fields has been preceded by much laboratory and field research on the use of various chemicals2,3 for solving numerous well-completion and work-over problems. Plastics now are being used successfully to control gas-oil and water-oil ratios,4'6 in zone isolation, the repair of casing leaks, the elimination of caving in cable-tool drilling wells6'7 and in the setting of linerss and casing.9 Sand-consolidating plastics, however, are basically different from all others in that they must not form an impervious seal. Field Practices The approach to the sanding-up problem usually has been the mechanical obstruction of the movement of the sand grains.

Jan 1, 1947

By A. C. Polk, R. H. Smith

The physical properties of the materials are listed, together with a short explanation of how this material binds the sand grains together without materially reducing the effective permeability of the sand. The chemical can be used in wells with bottom-hole temperatures ranging from 105°F to more than 350°F A description of the equipment required and the techniques used for applying these plastics to the wells is included. Introduction Recovering oil and gas from unconsoli-dated sand formations offers one of the most troublesome of all production problems. These sands generally present no particular trouble while drilling is in progress, but after the well has been completed and a pressure differential has been established across the face of the producing zone, the formation begins to L'slough," resulting in "sanding up" of the well. The term "sanding up" means that sufficient volumes of sand have moved into the well bore or casing to cause a serious reduction or complete halt of all flow of oil, water or gas. In rare cases a well may produce only a small amount of sand and still continue to flow or pump, the sand being carried to the surface in the fluid stream. However, in such instances, the result may be a costly repair bill due to the effect of the sand on surface and pumping equipment. The difficulty of producing petroleum from sands that are loosely cemented has long been recognized by petroleum engineers but only within the last few years has any new approach to the problem been undertaken. This involves the use of plastics that are capable of bonding the individual sand grains in place without materially reducing the effective permeability of a formation. The successful application of plastics for the consolidation of poorly cemented sands is relatively recent but now it is widely used in many of the more difficult areas on the Gulf Coast of Texas and Louisiana. This relatively new use of plastics1 in the oil fields has been preceded by much laboratory and field research on the use of various chemicals2,3 for solving numerous well-completion and work-over problems. Plastics now are being used successfully to control gas-oil and water-oil ratios,4'6 in zone isolation, the repair of casing leaks, the elimination of caving in cable-tool drilling wells6'7 and in the setting of linerss and casing.9 Sand-consolidating plastics, however, are basically different from all others in that they must not form an impervious seal. Field Practices The approach to the sanding-up problem usually has been the mechanical obstruction of the movement of the sand grains.

Jan 1, 1947

By Julyana G. Santana, Esperidiana A. B. Moura, Vijay K. Rangari, Olgun Güven, Angel Ortiz, Rene R. Oliveira

Ethylene-vinyl alcohol (EVOH) copolymers are widely used in the food packaging industry as gas barrier properties to oxygen, organic solvents, and food aromas. EVOH is very sensitive to moisture and its gas barrier ability deteriorates in high relative humidity conditions.This work aims to prepare flexible films based on melt-blending high density polyethylene (HDPE) and ethylene-vinyl alcohol (HDPE/EVOH/EVA blend) reinforced with graphene oxide (GO). The HDPE/ EVOH/EVA/GO flexible films were prepared by twin-screw extrusion and blown film extrusion processing. The flexible films samples were characterized by tensile tests, TG, DSC and FE-SEM analysis and the correlation between properties was discussed. In addition, the oxygen permeability tests were performed at 23 °C, 0 and 90% relative humidity using an OX-TRAN (MOCON Inc.).

Mar 1, 2017

By Iga Trisnawati, Fitria Puspita, Himawan Tri Bayu Murti Petrus, Gyan Prameswara, Idi Amin, Andi Nurfaadhilah Ulfah

Laterite ore is a valuable resource due to its high content of metals essential for modern technology, including nickel, iron, and cobalt. However, extracting nickel from laterite ores is challenging due to their complex mineral composition and low nickel concentrations. This study examined the leaching behavior of pre-roasted laterite ore and the effect of roasting on leaching kinetics. The ore was roasted at temperatures of 280°C and 610°C for 3 h, followed by sulfuric acid atmospheric leaching. The results demonstrated that pre-roasting at 610°C significantly enhanced nickel leaching recovery, with up to 93% nickel successfully recovered. The leaching process of pre-roasted laterite ore was found to be controlled by diffusion through the ash layer, with activation energy values of 20.97 and 18.97 kJ/mol for laterite roasted at 280°C and 610°C, respectively. These findings indicate that pre-roasting can improve the leaching performance of laterite ore, potentially leading to more efficient and sustainable nickel extraction processes.

Feb 27, 2024

By James Crosby

The Urad property had been worked intermittently for over 50 years before American Metal Climax (AMAX) started an extensive exploration program on this property in 1961. The detailed studies of the property proved a large ore body of low grade molybdenum ore that could be mined by modified panel caving methods. Mine development and mill construction for a 5000 TPD operation was completed in July 1967. The Urad mine and plant site is located 55 miles west of Denver near Berthoud Pass. The plant elevation is 10,200 feet. The crushing plant is located underground because available surface area is re¬stricted by snow slide hazards. Crushing plant layout and ventilation system design for the Urad mine was based on our operating experience at similar crushing facilities located at the Climax operations. Low speed conveyors of generous width, adequate exhaust volumes at all ore transfer locations, large hoods and good conveyor skirting have made the Urad underground crusher dust control operations very satisfactory. Good maintenance and cleanup of the crusher facilities have made a clean working area with very low dust exposure. The ore from the mine is dropped approximately 1000 feet through ore passes to scraping drifts above the crusher and then transferred to the coarse ore bin by 150 h.p. slusher hoists. A reciprocating plate feeder under the coarse ore bin feeds a 48 x 60 jaw crusher. Ore from under the crusher is conveyed on a 48 in. belt to a vibrating screen where oversize passes through a 7 ft. Standard cone crusher. The crushed ore along with the screen undersize is conveyed on a 42 in. belt to a 1000 ton surge bin.

Jan 1, 1971

By J. H. Zietsman

It has previously been observed that industrial high-titania slags display a compositional invariance, remaining close to stoichio-metric M3O5. The present study focuses on this invariance and the phenomena which may cause it. The invariance was studied using thermochemical calculations and a mechanism is proposed for the observed behaviour. The mechanism suggests that a combination of thermochemical equilibrium and transient slag solidification and melting results in the observed compositional invariance. The proposed mechanism provides new insights and prompts questions about other mechanisms in the smelting process.

Jan 1, 2004

By Sergei Decterov, Peter Hayes, Evgueni Jak, Taufiq Hidayat, Denis Shishin

Copper smelter operations around the world are under sustained pressure to reduce costs and increase output. Through the provision of reliable data on fundamental properties of the chemical systems the opportunities for improvements of industrial copper production can be identified. Experimental and modelling studies on phase equilibria, thermodynamics of copper slag/matte/metal/gas systems have been combined into an integrated research program undertaken at PYROSEARCH. Experimental phase equilibria studies involve high temperature equilibration in controlled gas atmospheres, rapid quenching and direct measurement of compositions of equilibrium phases with electron probe X-ray microanalysis (EPMA). Thermodynamic databases development and modelling is undertaken using the computer package FactSage in conjunction with advanced models used for complex solution phases. Progressive development of these research methodologies has brought significant advances in characterisation of these complex systems, including a new optimised thermodynamic database for the copper-containing slag system Cu2O-Al2O3-CaO-FeO-Fe2O3-MgO-S-SiO2.The new data and models can now be applied to assist in improvements of the processes. The effects of changes to chemistry and process conditions within the smelting reactor can be examined. Several examples of new descriptions of the phase chemistry of the Cu2O-CaO-SiO2 and Cu2O-FeO-Fe2O3-SiO2 systems in equilibrium with metallic copper showing calculated and experimental data are presented.

Jan 1, 2014

By S. Gaydardzhiev

Laboratory batch tests having preliminary and orientation character aiming at improvement of the molybdenum flotation at Ellatzite copper processing plant in Bulgaria have been conducted. The following technological parameters have been screened to study their influence on the grade and recovery of copper and molybdenum during the rougher flotation stage: flotation pulp density, pH, addition of secondary collector and replacement of MIBC by pine oil as a frother. The results have shown that slightly better grade/recovery figures could be obtained for both copper and molybdenum at lower flotation pulp densities. The addition of kerosene has improved the recovery of molybdenum however, on the expense of that of copper. The effects from pH variation and the replacement of MIBC by pine oil as a frother have been almost negligible.

Sep 1, 2012

By Barbara J. Arnold

The Electric Power Research Institute (EPRI) and six EPRI-member utilities are sponsoring research to define relationships between coal properties and coal handling behavior. Deratings and outages caused by plugged chutes or bunkers or frozen coal can cost utilities millions of dollars annually in lost energy production as well as in manpower to restore coal flow. There is also the added expense of maintaining redundant equipment to assure a continuous coal feed to the boiler, a common practice for utilities. Over the past two years, researchers at CQ Inc. and Iowa state university have collected and analyzed coal samples to develop a coal handleability index for utilities to use when specifying coals for their power plants. These coal samples cover ranges in ash content, rank, grindability, size distribution, and moisture content--properties that affect the handling behavior of coals. Other properties, such as the washability and ash composition, are measured as well. Over the remaining two years of the project, all of these analyses will be correlated to handling behavior, measured using a triaxial shear tester that determines the strength of a coal under compression. An index will be developed and validated at host utility power plants.

Jan 1, 1991

By Shuangchun Yang, Le Tong, Ronggui Fan, Cunlei Li

Acid mine drainage (AMD) is difficult to treat due to its physicochemical characteristics, such as high pH and high heavy metal concentrations, so it causes great harm to the environment and human health. If acid mine drainage is discharged arbitrarily without treatment, it will lead to a series of environmental problems and cause long-term environmental pollution. In this paper, the source and hazards of acid mine drainage are introduced in detail. And the principle, the mechanism, the application, and basic information of the current primary technology of the treatment for acid mine drainage are comprehensively introduced and summarized. The summarized treatment technologies for acid mine drainage mainly include neutralization, sulfidization, constructed wetland method, adsorption method, microbiological method, ion exchange method, membrane technology, and microbial fuel cell technology. Also, the primary technology of treatment for acid mine drainage is systematically compared and evaluated. Moreover, some suggestions on the development direction of water treatment technology in the future are put forward. This paper provides a scientific reference for scientific and technical works to treat acid mine drainage.

Sep 4, 2020

By Thenepalli Thriveni, Seong-Young Nam, Nam-Il Um

New modern water treatment technologies required for arsenic removal from waste waters contaminated extensively by various background sources from mining, industrial waste, agricultural waste, painting industry and natural geological bed rock system etc. Arsenic is a widely dispersed element in the earth's crust and exists at an average concentration of approximately 5 mg/kg. Arsenic (As) and heavy metals may be released from the mine wastes to the ground and surface water systems, as well as the geological environment due to their solubility and mobility. This research focuses on the effect of accelerated carbonation process for successful removal of heavy metal arsenic anions from artificial waste water and mining waste waters. This accelerated carbonation process is a simple and novel method with 85 ~ 88% removal efficiency. Carbonation has been studied as a process to further improve immobilization of solidified/stabilized waste and granular waste. After successful removal of arsenic anions from solid mining waste and its potential benefits for producing construction materials. Besides, the industrial and urban management systems are generating bulk solid mining wastes, and most often dumping them in open fields. To prevent the landfilling with mining waste, many efforts are being made for the recycling of different types of mining solid wastes with a view to utilizing them in the production of various construction materials.

Jan 1, 2014

"Quang Ninh province is located in the north east of Vietnam and the coal mining in the province generates two thirds of the province’s GDP. The coal is extracted from both open pit and underground mines for the country’s complete coal export and by a share of more than 90% for domestic coal usage. Overburden generated through open pit mines is piled up nearby in the form of large waste rock dumps. The side-hill fill dumping near open pit mines is the source of environmental degradation in the region. Among the current problems at solid waste rock dump sites are dust emissions during and after dumping as well as Acid Rock Drainage (ARD). One of the major existing problems at waste rock dumps is dump stability (comprising erosion, sliding and subsidence issues). The RAME R&D project (Research Association Mining and Environment in Vietnam) is - among other activities - actively involved in the research for stabilisation and rehabilitation of mine waste rock dumps in Vietnam in the form of several sub-projects. The Institute of Mining Engineering I of RWTH Aachen University is leading the sub-project of mine waste dump stabilisation in co-operation with Chair of Geotechnical Engineering and Brenk Systemplanung GmbH. Mine waste dumping in the form of layers as an alternative to the side-hill fill dumping is expected to bring up environmental and economical benefits by minimising the problems of dump sites with the contribution to a sustainable development. Reduction of the post construction settlements, long term stable dump profile with minimum erosion, improvement of material parameters for geotechnical slope stability through compaction from hauling trucks as well as economical evaluation of new dumping concepts are the areas of the current research. The project has been financed by German Federal Ministry for Research and Education (BMBF). The ultimate aim of the sub-project is the compilation of the project results in the form of a "Best Practice Guide" and software based "Decision Support System" for planning and management of solid mine waste dumps."

Jan 1, 2011

By R. David Prengaman

During the past several years a new insoluble lead anode has been developed for copper electrowinning. The new anode consists of a rolled lead-calcium-tin alloy sheet attached to a slotted copper bus bar by a soldering process which produces a complete metallurgical bond between bar and sheet. The metallurgical bond greatly reduces the resistance between the bus bar and the lead sheet and the high conductivity does not deteriorate during the life of the anode. The rolled anode thins uniformly and does not suffer preferential grain boundary or internal corrosion commonly seen in cast anodes. The lead-calcium alloy containing a high tin content corrodes slowly because the rolling process produces a uniform, fine grained structure. The wrought product is very strong and ductile; and contains no internal defects, segregation, cracks, or pores which can reduce the life of the anode. Because the anodes corrode uniformly, a high percentage of the anode thickness can be utilized thus extending the life of the wrought anodes. The anode alloy composition which is stable only in wrought form, produces exceptional resistance to passivation during current interruptions. First introduced into liberator cells, the new electrowinning anodes have been specified as the anodes of choice for every new SX-EW tankhouse constructed in the last two years. This paper describes the new anode, its method of construction, service history, and how it differs from present copper electrowinning anodes.

Jan 1, 1987

By Abolfazl Eslami, Fatemeh Rostami, Sara Heidarie Golafzani, Mohammad Arabameri

Collapsible loess is classified as problematic soil found in most continents. The loess immediately collapses under stresses induced by axial compressive loading or the soil weight when exposed to moisture. In Iran, vast areas of the Golestan province are covered with aeolian loess deposits. This paper investigates whether the simultaneous effect of inundation and pre-loading in helical pile installation are operative and effective in improvement of Golestan loess. The effect of installation conditions on loess collapsibility is studied via two main approaches, i.e., field investigations and physical modelling. The experimental studies include installation of eight single helix piles in the Amirkabir University of Technology Frustum Confining Vessel, i.e., FCV-AUT. Also, four single helix piles with embedment depth of 3 m and diameter of 250 mm were installed in Golestan province and full-scale pile static loading tests were performed. The results indicated that the simultaneous application of crowd loading and water pressure during installation of helical piles results in better soil shear strength parameters. Moreover, high crowd stresses or low crowd stresses accompanied by water pressure during pile installation brings about similar load-displacement behavior of model piles installed in FCV-AUT and full-scale helical piles.

Oct 1, 2022

By L. W. Kempf

A BALANCED system of internal stress is set up in any metallic structure by plastic deformation below the annealing temperature. The internal stress induced by cold rolling or other fabricating processes is generally recognized and its magnitude is known to be, within certain limits, a function of the degree of cold deformation. The plastic deformation that may accompany rapid cooling from elevated temperatures may not materially change the form of the product. The internal stresses so induced are not, therefore, so evident and nonrecognition of their presence has at times led to engineering failures. The heat treatment of aluminum alloys is a relatively new art and little information is available regarding the magnitude of stresses induced luring the commercial heat treatment of aluminum alloy products is the industrial use of aluminum increases, it is inevitable that products of increasingly large volume be required. It has become necessary in the present commercial utilization of aluminum to heat-treat castings and forgings weighing hundreds of pounds. One of the factors governing the magnitude of internal stresses arising from rapid cooling at elevated temperatures is that of the, size of the structure being treated. Some of the other factors are: cooling rate, elastic properties of the alloy, thermal expansivity, thermal conductivity, and the presence or absence of phase changes. Practically all aluminum alloys have a high coefficient of thermal expansion and some are capable of developing relatively high

Jan 1, 1934

By S. G., Lasky

IT seems to be in the nature of concepts that they have many meanings, and that the meaning best reflecting the primary interests of a person tends to be accepted by him as the normal meaning of the concept. The concept of ore reserves is no exception, for there is no unanimity of meaning among the several groups of us who are interested in ore reserves, nor even among the individuals of a single group. The groups most interested in ore reserves would seem to include at least the mining industry, perhaps State taxing agencies, and the Federal Government in all its diversified activities, and I would include also the citizenry at large or at least that part of it that consciously thinks about problems-of national welfare. To each of these, and to different individuals within them, the term reserves represents something different, and the farther away the individual or group gets from physical contact with the ore, the more abstract does his or its concept become. It is something different to the policy maker from what it is to the fact-finder or to the miner.

Jan 1, 1945

By Harald F. Solberg

A preliminary study of the performance of a 4-inch Krebs cyclone at near rope conditions and different feed slurry temperatures was completed. Results suggest that temperature influences the x50c size which, in turn, did not depend upon spigot diameter. The bypass correction to a reduced efficiency equation incorporating the concept of a critical size xo was a function of fractional water recovery to underflow and may depend on feed size and feed percent solids. Further experimentation is required to develop an accurate model at near rope conditions.

Jan 1, 1981

By А. А. Vasiliev, Y. G. Seredkin, А. V. Aksenov, А. Y. Senchenko

Refractory gold-containing concentrates usually contain gold enclosed in sulphides as well as in rock-forming minerals. Another difficulty is that gold often occurs as very fine inclusions of several micrometres, and even smaller than 1 micrometre, or can be part of the mineral composition at the structure level. Processing of such concentrates is a challenge. Ultrafine grinding and further oxidation are applied for gold liberation. The paper deals with the results from the study of gold deportment using Qemscan, and atmospheric oxidation testwork involving Albion Process™ on a gold-containing concentrate with a high content of refractory gold in sulphides and gangue minerals. Albion process testing was performed at Institute TOMS with the participation of Glencore Technology Pty Ltd (Australia). Additionally, conventional cyanidation testwork was carried out for the concentrate processing. As an alternative technology of gold liberation, oxidising roasting with arsenic stabilisation was used. The results from the study make it possible to assess the efficiency of the above-mentioned methods of gold liberation, and applicability of Albion technology to recover gold from the refractory concentrate. Key words: Gold, refractory concentrate, Albion Process, atmospheric oxidation, oxidising roasting, leaching

Jan 1, 2020

By J. B. Gayle

Since the turn of this century, there has been increasing interest in the application of flotation processes to the beneficiation of finely divided minerals of various types, This is reflected by the large numbers of papers dealing with various aspects of this problem published annually both in this country and abroad. For the most part, such papers fall into one of three categories: 1. Those concerned with achieving, by various chemical and/or physical means, a set of conditions under which certain particles become potentially floatable while others do not. 2. Descriptive studies of plants and pilot plants effecting separations between such particles. 3. Studies of the effects of certain design and operating variables on the rates and efficiencies with which such separations can be effected.

Jan 1, 1959