Search Documents

By Rob Farnfield, Ben Williams, Bob Woolley

This paper outlines how drilling safety standards are being driven forward in the United Kingdom’s surface mining and quarrying industry with developments in equipment, procedures and competence.

Jan 1, 2010

By Anjana C. P, K. Ranga Swamy

The hilly regions of Kerala are severely affected by excess rainfall, causing tremendous damage due to landslides and slope failures. It is necessary to strengthen the existing slope profiles to prevent such disasters and avoid their risk to human lives and civil infrastructures. This paper studies the effect of micro pile to reinforce the slopes in Idukki district of Kerala, where slope failures are frequent. Three-dimensional slope stability analysis is carried out on slopes from the Idukki to obtain safety factor values using the MIDAS GTS NX program. The slope is fully saturated herein by taking the model's piezometric surface at the ground level to simulate high rainfall intensity. The critical slopes are then modelled with micro piles to analyze their effectiveness in improving the stability under static conditions. Different micro pile arrangements are considered, and a series of slope stability analyses have been carried out to obtain the optimum configuration with the required safety factor. The FOS values increased by more than 50% with micro piles for all the slopes. The optimum micro pile arrangement obtained for each slope shows that micro pile distribution between the toe and middle of the slope is an effective location for reinforcing slopes.

Sep 1, 2022

By Hennessy F. L

IntroductionEvolution of the Present SmelterRoastingFiringHearth SlopeDust HandlingFurnace DetailsSmeltingFurnaceFeed DeliveryPulverised Coal FiringWaste Heat BoilersDust HandlingAir PreheaterReverberatory Slag DisposalConvertingVesselsAir SupplyMatte TappingConverter Slag HandlingPurchased Ore PlantINTRODUCTIONSmelting in blast furnaces commenced at Mount Morgan in 1906, when copper, which interfered with gold recovery by chlorination, became an asset. After various changes in blast furnace practice, reverberatory smelting com...

Jan 1, 1952

By T. B. Crowe

MucH has been written upon the precipitation of metals from cyanide Solution by zinc. We often read of the many factors that influence precipitation, such as zinc surface, purity of zinc, percentage of lead, temperature of solutions, strength of solutions in cyanide or alkali, etc. -Little do, we hear, however, of the part that oxygen plays in precipitation. Caldecottl says: "As the dissolving of gold is essentially an oxidation process, so its precipitation is one of reduction." All who have studied or worked with cyanide solutions will agree that Caldecott's statement is true.' . In the cyanide work in the mills of the Portland Gold Mining Co., we have always found oxygen to be the greatest enemy to precipitation. Oxygen Antagonistic to Good Precipitation A few years ago, while making some experiments on the effect of pressure upon the dissolving rate of gold from our ores, to prove a point, I made some bottle tests under vacuum. The results were surprising, and showed that under vacuum practically no gold dissolved, which confirmed my belief that Elsner's equation was true and also led me to investigate the amount of dissolved air carried by solutions at atmospheric pressure. The experiment consisted in partly filling an acid-bottle with mill-solution and connecting it by a rubber hose to a vacuum pump. When the vacuum was suddenly applied, a cloud composed of thousands of small air bubbles rose out of the solution, showing qualitatvcily' the amount of dissolved air that was contained in the solution, and also proving that the relief of atmospheric pressure on the solution permitted this dissolved air to escape. In studying literature on the subject, we find Henry's law—"The amount of gas dissolved by a liquid is proportional to the pressure to which the gas is subjected."

Jan 1, 1919

By N. Ragoonanthun

Paper written on project work carried out in partial fulfilment of B.Sc. (Mining Engineering) degree This report investigates the optimization of a raiseline in order to open up the ore reserve quicker. The project was carried out at Mponeng Mine (an Anglogold shaft formerly known as Western Deep Levels 1 Shaft and South Mine, in Carletonville). The project was divided into two focus areas namely: ?To design an optimum layout of a raiseline, which includes the scheduling of all activities for the establishment of the infrastructure. Consideration was given to the blasting practice, mining cycle, orepass placement and slusher positioning. Two designs were carried out on the above basis. ?The design of a ledging operation/practice to match the optimized layout of the raiseline. The ledging cycle design involved a thorough investigation into the possible use of drill rigs, Electronic Delay Detonators (EDD) blasting technology, longer drilled holes, Threshold Blasting (THROB),and water jet cleaning.

Jan 1, 2003

By David C. Oyler

The Bureau of Mines conducted research at the 9-Right Section of the Olga Mine to determine the cause of bumps and aid in the development of appropriate control techniques. The purpose of this paper is to identify the factors which affect the occurrence of bumps at the Olga Mine. These factors have been broken down into two categories, in situ and mining related. The in situ factors include those conditions which exist prior to mining, such as variations in lithology and overburden, presence of jointing, the composition and the physical properties of the rock, and the original stress field existing in the coalbed and adjacent strata. The mining factors include the mining sequence, changes in stress in the coalbed and adjacent strata during mining, rates of convergence, and the pattern of failure of the coal and adjacent strata. The factors which appeared to have the greatest effect on bumping were the overburden, the lithology of the roof and floor rock and the physical properties of the rock. The roof rock is generally a massive, stiff sandstone which does not break until coal pillar extraction is complete. The immediate floor is a strong shale which generally grades into siltstone and then into sandstone. The overburden at 9-Right ranged from 990 to 1,600 ft. Secondary factors appeared to be the in situ (pre-mining) stress and the mining sequence. When barrier pillars were split., pressures measured in hydraulic cells (Borehole platen flatjacks) located in those barriers showed large pressure increases, and the incidence of bumps increased, especially when the barriers were near old gob areas. The pillar extraction system used at Olga, where three rows of pillars are mined concurrently, appears to reduce pillar loads at the face areas, thereby reducing the exposure of men and equipment to the risks of bumps during mining operations. The horizontal components of in situ stresses at Olga were found to be nearly the same as those at 5 other mines in southern WV, where humps were not common, so it appears that horizontal in situ stress alone is not a major influence on bumping at the Olga Mine.

Jan 1, 1987

By J. Fellowes, Z. Liang, J. Robson, M. Kenyon

"Dispersoids play a significant role in the recrystallization and texture development for wrought Al-Mg-Si (6xxx series) alloys by inhibiting grain boundary motion. It is therefore important to understand the precipitation kinetics of such particles. It is the additions of Mn and Cr in Al-Mg-Si based systems that can lead to dispersoid phases being formed. These phases are currently thought to nucleate on ß’-Mg2Si via an intermediate semi-coherent precipitate. Scanning transmission electron microscopy (STEM) has been conducted to study the precipitation of a-Al(CrFe)Si and a’-AlCrSi dispersoids. Corresponding electron dispersive spectroscopy (EDS) has been used to distinguish the dispersoids. The volume fraction and size distribution of dispersoids has been measured as a function of distance across a grain. Electron probe microanalysis (EPMA) has been conducted to study the inhomogeneity of elements in the cast structure and the effect on dispersoid precipitation. Dispersoid free regions have been observed in the microstructure correlating to regions depleted in the dispersoid forming elements.INTRODUCTION Al-Mg-Si (6xxx series) based alloys are increasingly being used in the automotive industry. The primary reason is to reduce the weight of vehicles, resulting in a reduction of CO2 emissions and increased fuel efficiency. The demand for 6xxx series is predicted to increase over the coming decade. Due to the high cost and CO2 emissions produced by raw extraction of aluminium, close loop recycling of these alloys becomes a more important process. However recycling of automotive alloys can be difficult due to pick up of impurity elements such as Mn, Cr and Fe. The addition of these elements can form dispersoid particles during early heat treatment processes. Although a controlled population of dispersoids is necessary to control the grain structure during thermo-mechanical processing, a significant change to the dispersoid population due to a composition change could profoundly influence the final microstructure, affecting the final properties of the material. More research is required on the precipitation and effect of additional minor alloying elements; in order to increase the 6xxx series alloys recyclability."

Jan 1, 2018

The paper covers the history and develop- ment of electrical and diesel-powered hydrau- lic percussion rock drills. It examines main design aspects and problems encountered in pro- ducing an efficient and reliable machine to fully cover the nominal hole sizes required for underground development, production drill- ing and for general quarry work. The main design features and advantages of a hydraulic rock drill are relatively low input power requirement to energy per blow (this being achieved by the use of an electric or diesel- powered hydraulic system) and a specially con- structed piston using a powered damper cylinder to absorb the recoil forces from the drill steel and reduce stresses on the drill, feed and hydraulic boom. A further important design feature is the anti-jamming device which controls the drill both during manual and automatic operation. This anti-jam device works on feed and rotation press and prevents the drill bit becoming jammed in broken or soft ground. These features and many other mechanical and environmental benefits are highlighted when comparing hydraulic percussion rock drills with current pneumatic machines. The hydraulic rock drill gives an overall high penetration and production rate, with an added bonus for ergonomy and environmental conditions such as lower noise level, no fogging from air and oil exhaust (which naturally gives better air for breathing),plus improved vision when in under- ground situations. Hydraulic rock drills and systems have been fully tested in many mines, quarries and contract sites during the past years. They h6! been improved and modified and are now provi~ to be very reliable and economical piece drilling equipment whò in mines and quarries.

Jan 1, 1978

By Yoginder P. Chugh

Most mines are large producing 0-25 mmt annually. The coal is mine.) at depths ranging from .0-150 m 120-500 ft mining at 300 m .(,1000 ft) depth is anticipated in the future. Single and multiple seams ranging from 3-12 m 10-40 ft) in thickness are mined. Most overburden is unconsolidated and consists of sands, and sandy or silty clays. The stripping ratio (volume of overburden to volume of coal mined) varies from 3-L. The overburden and coal is mined in benches 8-12 m -(24-40ft) high; the high-wall angle is about 45 degrees. Bucket wheel and bucket chain excavators are commonly utilized for overburden and coal removal, Some of the large overburden stripping machines nave capacities. Ranging from 4400-10,000 bank cu ( 6000-14,000 BC) per hour. The overburden from the upper benches is transported around the pit using the trains and belt conveyors. It is deposited in the spoils using large stacker-conveyor systems capable of handling 2550-7300 cu m/hour (7500-10,000 cu yds/hour). The overburden from the bottom two or three benches is transported across the pit using the conveyor bridges which are computer controlled. Conveyor bridges capable of handling overburden up to 60 m (200 ft) high are currently in use; a 60 a (20e ft) high conveyor bridge has a capacity of 85 x 10 cu ( 118 x 10 cu yd) annually. The coal is loaded in the trains directly and shipped to power plants or coke oven plants.

Jan 1, 1980

By George K. Foster

The Jeffrey mine of the Canadian Johns-Manville Co., Limited, is in the town of Asbestos, situated approximately 100 miles northeast of Montreal and about the same distance southwest of Quebec, in Richmond county, Quebec. Mining operations were started in 1881 on outcrops on a hill, as a side-hill cut, followed by a second and third cut. This development was the forerunner of the present large open-pit operations, the mine now ranking as the largest open-pit asbestos mine in the world. Operations were first carried on by hand, then by horsepower and later by stem cableways. By 1914, the derrick spans, 2,000 feet or more long, became unwieldy. To overcome this, and also to eliminate hand labour as much as possible, steam shovels and railway haulage were introduced. The steam shovels were replaced in 1928 by larger electric shovels of the full-revolving type.

Jan 1, 1946

By Elton L. Litchfield, Milton L. Weiss

Studies were made on the projectile impact sensitivity of explosives by subjecting explosive samples to the impact of metal projectiles fired from a 0.50- caliber gun . The projectiles , in the form of right cylinders , made plane surface to plane surface contact with the explosives . Pressures in the explosive were investigated with an expendable pressure transducer in some instances . The physical model of the projectile - explosive interaction describes , in principle , the duration of the peak shock pressure in terms of the projectile and explosive geometry and the steady- state penetration of the explosive . Of the explosives studied , liquid hydrogen- solid oxygen and liquid oxygen - solid or liquid hydrocarbon fuel were the most shock sensitive ( requiring an initiating shock of about 1.0 kb or 987 atmospheres pressure ) ; cast TNT was the least sensitive ( requiring an initiating shock of more than 110 kb pressure ) . Measurements of pressure in the explosive showed some moderate space resolution by the transducer and gave pressure distributions in agreement with expectations from the model of the shock processes . The appearance of the recovered projectiles and the calculated initiation shock pressures suggest that the solid explosives were initiated directly to high- order detonation , whereas the liquid explosives were probably initiated to low- order detonation-- with a subsequent , later transition to high- order detonation .

Jan 1, 1965

By Kenneth L. Rubow, Virgil A. Marple, Zhigun Zhang

"A theoretical technique has been developed and verified experimentally for determining the aerodynamic diameter of irregular shaped particles. The aerodynamic diameter of a particle is a very important parameter for determining where that particle deposits in the respiratory tract. Many instruments, such as impactors and cyclones, will determine the aerodynamic size distributions of aerosol particles but few analyze the particles individually. The theoretical approach of our technique is to solve, by use of high speed computers, the three-dimensional Navier-Stokes equations to obtain the flow field around an irregular shaped particle of any contour. The computer program will then determine the drag on the particle, and thus the aerodynamic diameter of the particle can be calculated. The experimental approach has been to pass the particles through a centrifuge and collect the particles upon a collection foil. The position of a particle on the foil is an indication of its aerodynamic diameter. These particles were then shadowed in two orthogonal directions and inspected under an scanning electron microscope (SEM). The top view of the particle in the SEM plus the views of the two orthogonal shadows allows one to determine the three-dimensional shape of the particle. Studies have been performed on silica, coal and talc particles with aerodynamic diameters in the 1 to 4 µm size range. The three-dimensional shape, as is determined from SEM analysis, was used in the theoretical computer program and the results compared. It was found that in most cases the agreement between the experimentally and theoretically determined aerodynamic diameters was within 5%. INTRODCJCTIONThe equivalent aerodynamic diameter (EAD) of a particle, defined as the diameter of a unit density sphere with the same falling speed as the particle in question, is an important size measurement of the particle. This is especially true when attempting to predict where particles may deposit in the respirator tract. Therefore, EAD is an important parameter when considering respiratory diseases caused by particles, such as coal workers pneumoconiosis (CWP).Many instruments will measure the EAD size distribution of the aerosol particles, but few analyze the particles individually. Impactors, cyclones and virtual impactors normally collect particles upon substrates or filters which are · then analyzed gravimetrically to determine the mass concentration of the particles in that size classification. The EAD of particles can be measured on an individual basis with centrifuges, inertial spectrometers and the TSI Aerodynamic Particle Sizer (APS). Centrifuges are most ideally applicable for studying individual particles as the particles are deposited, on long removable foils, at locations dependent upon their EAD."

Jan 1, 1990

By E. J. Onuscheck

With passage of the Federal coal' Mine Health and Safety Act of 1969, many challenges have been directed to the industry's mining and safety engineers. The most critical challenge is that of ventilation. The language concerning ventilation in many sections of the Act could very well deprive or limit the mining engineer in planning the ventilation for new mines, since the Act requires federal approval of all ventilation plans. Dependent upon approval and of course application of the law, this could, due to economics, prohibit the opening of new mines in some cases. Petitions for modification of some mandatory standards relating to ventilation have already been filed under Section 301(c). It is quite possible that many of these standards may be modified.

Jan 1, 1970

By M Singh, R C. Steinhaus, J J. Rust

Metallurgical process control systems in mineral plants often employ state-of-the-art monitoring analysers in an attempt to optimise plant operations and enhance mineral recoveries. These systems are unfortunately invariably fed by simplistic ‘sampling’ designs consisting of various in-stream methods or pressurised probes. These are unfortunate compromises and provide a false picture of what a mineral flotation or other process can achieve. The situation is further aggravated by some manufacturers using misleading marketing to suggest discrete cross-stream methods for metallurgical accounting and unreliable continuous in-stream off-takes for control sampling and that they are of synonymous integrity.Reliable, absolute or representative samples are often absent in many modern day concentrator plants, due to compromises around sample taking, particularly in terms of delineation and extraction errors and thus leading to sample bias. For more reliable information from online analysers we need a continuous, but much more reliable sample taken, than is current practice.Online analysers require a fully proportional and continuous supply of sample for effective process control, otherwise maximised or benchmark recoveries will be nothing but a pipe dream. Large discrete cross-stream samples from mechanically less reliable equipment cannot be used as feed to online analysers, as it will negatively impact real-time feedback and efficient process control.It is possible to build correct sampling systems that could do both process controls online and metallurgical accounting at the same time. Multotec Process Equipment (Pty) Limited, in close association with experienced sampling consultant Francis Pitard, have jointly patented a concept to achieve this and which is embodied in the design of the unique Rotating Cone® Sampler (International Patent Application No. PCT/IB2016/057464). This versatile unit for dry and wet applications has high division ratios via two-step sampling and division.A prototype was built and tested to validate the design and levels of precision achievable when employing the unit to split dry mineral fines or even certain foodstuffs.CITATION:Steinhaus, R C, Rust, J J and Singh, M, 2017. Does process control sampling always have to be a compromise?, in Proceedings Eighth World Conference on Sampling and Blending , pp 197–202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By John E. Young

United States Steel Corporation's Winifrede Mine is operated by Lynch District in the mountainous region of Eastern Kentucky. This region is characterized by narrow mountain ridges and precipitous slows which present both an opportunity and challenge in the design and selection of coal handling facilities for the movement of coal from the section belts to the railroad cars. The narrow finger ridges precluded use of underground haulage and, thereby, presented the opportunity to use high capacity equipment on the outside bench. The precipitous mountain slopes, steepest at the Winifrede seam horizon, presented a challenge to select a solution for lowering the coal approximately 1000 feet from the seam level to the valley floor railroad load-out point. It was evident from the start of planning that these two factors predominated; namely, rail haulage and coal lowering, and solutions to these would determine the final design of the Winifrede Mine coal handling facilities.

Jan 1, 1970

By D. G. Hulbert, J. H. Schubert, R. G. D. Henning

"Froth depth, along with reagent addition and aeration rate, is one of the crucial factors that can be used to control a flotation circuit. Sub-optimal setpoints and disruptions in levels have a severe adverse influence on grades and recoveries. A novel control strategy has been developed which provides exceptionally tight regulation of pulp levels. The controller observes and acts on all the flotation levels simultaneously. This provides a clear improvement over the standard approach, which is to use a set of Pl controllers. The system has been run on several industrial plants and has resulted in reduced fluctuations in level; fast responses to setpoint changes, and fast settling times after start-ups or disturbances. Testwork has shown that the improvements in level stabilisation translate into improvements in recovery and grades.IntroductionProcess control and optimization have an important influence on the economic efficiency of flotation plants. Inefficient operation can allow the wrong balance between grades and recoveries, and can also lead to adverse shifts in the grade-recovery relationship. Of all metallurgical operations, flotation loses the largest proportion of valuable material. Better operation can reduce these losses.An essential requirement of a good controller is that it should be able to stabilize and regulate the plant. Stable operation allows the performance of the plant to be observed without being obscured by the effects of disturbances and fluctuations. The optimum conditions can then be detected more easily. Good regulation can maintain operation at the optimum with proper neutralization of disturbances. Only when good stabilization and regulation are achieved can an optimizing strategy be properly applied.Froth depth, aeration rate and reagent addition are the three means by which a flotation plant is generally controlled. These control actions are effective on different time scales. Reagent addition is slower in its effect as some conditioning time is required. Since reagents are only added at the head of the circuit and at a few selected points within the banks, time is required for the effect of reagent changes to move through the circuit. Because of this slower time constant, reagent addition is more suited to process optimization and to dealing with slower changes in the process. An example of these slower changes is variation in the feed."

Jan 1, 1995

Protect rescue workers fighting fires or mine personnel temporarily working in hot environments from heat stress. Approach A specially designed ice-cooled vest is worn while working in hot environments where cooling the mine air is not possible. How It Works The vest holds a total of 44 individual ice cells in packets that are firmly held near the wearer's skin. These ice cells remove heat from the wearer, reducing heat stress and increasing comfort. The locations of the ice cells and packets are shown in the diagram. The vest is constructed in three layers with the outer layer being aluminzed fiberglass cloth. Its aluminized surface reflects radiated heat, and its fiberglass cloth provides fire resistance and strength.

Jan 1, 1979

By K. Perry, B. Lusk, Q. Huang, R. Honaker

"Rock dust is applied in underground coal mines to prevent the propagation of coal dust explosions. The application is conducted either dry or wet. Both methods have advantages and disadvantages however the formation of caked rock dust particles is cited as a significant concern for wet applications. A study was conducted to evaluate the effect of modifying the rock dust particle surfaces to repel water and each other by the addition of oleic acid (OA) and sodium oleate (NaOL). At a NaOL dosage of 2 lbs/ton, a contact angle of 112o was measured indicating strong surface hydrophobicity and ability to repel water. FTIR studies indicated a chemisorption mechanism which is necessary for long term stability of the surface modification. The dispersion rate of the modified rock dust samples was elevated by the application of both OA and NaOL thereby indicating a significant reduction or elimination of the detrimental effect of caking. Tests in an explosion chamber showed a 79% reduction in the dust explosion potential relative to untreated rock test applied by the wet technique. INTRODUCTION Mine explosions have been a long-time threat to underground coal miners attracting significant attention to the accumulations of combustible dusts and gasses. In the presence of sufficient oxygen and heat, the accumulations of combustible dust and gass can lead to large-scale underground coal mine explosions [Harris et al., 2010]. To alleviate the problem, rock dust such as limestone can serve both as a thermal inhibitor and a heat sink to inert the coal dust explosibility thereby prohibiting the occurrence of dust explosions [Richmond et al., 1975; Amyotte et al., 1995; Dastidar et al., 1997; Man et al., 2009]. The dispersibility of the rock dust is an important characteristic that determines the degree of explosion prevention [Greenwald et al., 1938; Mozumdar et al., 1974; Amyotte et al., 1995]. Unfortunately, the environmental conditions of an underground mine has the potential to cause caking of the rock dust which reduces the dispersive characteristics needed. The dispersive property of rock dust can be enhanced by modification of the particle surface properties by the application of chemical additives [Greenwald et al., 1938; Mozumdar et al., 1974; Spence, 2004; Vogt, 2011; Doidge et al. 2014]. The major mechanism for rock dust caking is the adsorption of water which forms liquid bridges at the particle-particle contact points where saturated solutions of soluble powder ingredients are present. Changes in temperature or relative humidity result in solvent (water) evaporation and the formation of dry bridges [Rumpf, 1958; Specht, 2006]. One method to prevent caking is creating hydrophobic rock dust to repel water from the solid surface thereby preventing the formation of liquid and solid bridges."

Jan 1, 2015

By B. K. Larkin, H. R. Bailey

A model Of heat flow in an underground combustion process is studied. This model includes convection effects and thus is more general than previous studies which considered conduction as the only mechanistn for heat transfer. Both linear (tube run) and radial (field application) geometries are considered. The effects of ignition heaters, vertical losses and finite source width are considered for the linear case. The results are in the form of equations and are presented in graphical form for a number of cases. Convection effects increase frontal temperatures about 25 per cent over those computed for conductive transfer for typical field operating conditions. This increase in temperature is a result of heat being transported toward the front by the injection gas. Even greater temperature increases are realized as the per cent oxygen in the injection gas decreases. It is well known that compression costs are of considerable importance in estimating the economic feasibility of underground combustion. By assuming an ignition temperature for the combustion fuel, predictions of limiting conditions on fuel density and injection rate necessary to sustain the combustion zone are made. For typical field conditions, at least 0.75 lb/cu ft of fuel are needed with air as the injection gas. If the injection gas is 10 per cent oxygen and 90 per cent nitrogen, this figure is 0.69 lb/cu ft. INTRODUCTION The possibility of increasing oil recovery by underground combustion has been considered for many years. Recent field tests indicate that the underground combustion process is technically feasible. The economic feasibility depends to a large extent on the amount of air which must be injected to sustain combustion. Prediction of the success of employing underground combustion in a particular reservoir must be based on existing field tests, laboratory tube runs"' and solutions of mathematical or analog models. Vogel and Krueger5 devised an electrical analog of the heat transfer problem in an underground combus-ion process. They considered the problem of heat conduction from a cylindrical source with increasing radius assuming no vertical losses. Bailey and Larkin and Ramey solved the corresponding problem including vertical losses by considering a mathematical model of the conduction process. Ref. 9, 10 and 11 also present information related to the subject study. The present paper generalizes these results to include both conduction and convection mechanisms for heat flow. A model of the conduction-convection process is described. The partial differential equations governing this model are written and solved for a number of cases of interest. The formulas are evaluated and the results are presented graphically. A CONDUCTION-CONVECTION MODEL Description of the Model A number of models are employed in this paper, each of which approximate a particular physical situation depending on the geometry, i.e., linear or radial flow, the type of vertical heat losses, the nature of the source, etc. The geometry for both the linear and radial case is shown in Fig. 1. A particular linear model is described in this section, and variations from this model are described in later sections of the paper. Consider a homogeneous, semi-infinite porous prism with lateral sides insulated as shown in Fig. 1. The left end, x = 0, is heated for a time t, with a plane heater supplying a constant heat flux and during this time; gas (nitrogen) is passed through the pores of the prism at a constant mass flux. At time t, the heater is turned off and air is injected in place of the nitrogen. This causes combustion to take place, and a uniform source of width 1 is formed which moves at a constant velocity v, to the right. The frontal velocity v, is related to the gas velocity v,, through stoichiometric considerations

By N. D. Ilankoon

"The use of thiosulfate as an alternative lixiviant for cyanide to treat complex refractory ores followed by the use of ion exchange resins (IX resins) for gold recovery has become an industrial reality. In this study, polyethylenimine (PEI) coated iron oxide magnetic nanoparticles (MNPs) were used to recover gold from the leaching solutions that consist of calcium thiosulfate, copper and gold. The gold loaded MNPs were easily separated from the solution using an external magnetic field. Proposing a novel adsorbent with characteristically easy solid-liquid separation, to recover gold from synthetic thiosulfate leaching solutions and gold elution and reuse of MNPs were the main objectives of this study. Adsorption isotherm studies revealed that the data fitted both Langmuir and Freundlich isotherm models equally well. The maximum adsorption capacity was 18.5 mg/g at pH 8 and 50?C. According to thermodynamic studies the physisorption process was exothermic and spontaneous. Gold and copper elution, and the regeneration and reuse of the nanoparticles were investigated and promising results were obtained. Different elution systems comprising sulfites, chlorides, glycine, EDTA (ethylenediaminetetraacetic acid) and sodium hydroxide were considered. Among them, EDTA for copper elution and NaOH for gold elution were the most efficient eluants. Regeneration and reuse studies revealed that the MNPs can be used for several cycles without significant performance loss. INTRODUCTION Although cyanidation has been used for gold leaching for more than 100 years, some major drawbacks associated with cyanidation have led to a quest for alternative lixiviants for gold leaching. Cyanide is ineffective in treating carbonaceous refractory ores as gold cyanide complex is adsorbed onto the native carbon in the ore itself known as preg-robbing. On the other hand environmental concerns associated with cyanidation drives the need for environmental friendly alternatives for cyanide. As of today, thiosulfate is known to be the most extensively studied and most promising alternative lixiviant for cyanide in both technical and environmental perspectives (Aylmore and Muir 2001, Oraby 2009)."

Jan 1, 2018