Search Documents

By W. O. Henderson, H. W. Seaney

The sinking and grouting methods employed at the 3C and 3D ore hoisting shafts and the No. 5 service shaft are discussed. The reasons for selecting a circular section over a rectangular one and other technical aspects are reviewed.

Jan 1, 1974

By Carl Tom Blevins

Resin was first introduced to U. S. mines in 1971 and first produced in 1973. The original polyester roof bolt resin was very expensive and limited to a single cartridge size and a single slow gel time. Early resin applications were limited to very difficult ground conditions. Today approximately 80% of the over 100 million roof bolts installed in U.S. mines, tunnels, and construction projects employ polyester roof bolt resin. The industry has evolved from hand packing samples for trial testing to producing enough resin, if converted to a .9 inch (22.9mm) diameter cartridge, to encircle the world at the equator approximately three (3) times each year. Manufacturing and design improvements allow for a more consistent product with a wide range of applications at a price that is approximately 30% below our 1974 sales price. An inflation adjusted dollar buys six (6) times more resin in 2006 than in 1974. Modern gel times range from a few seconds to over 15 minutes. Viscosity is matched to bolt type and drilling machine characteristics. Multiple cartridge diameters and a wide range of cartridge lengths are offered by two operating companies. Resin manufacturers have also gone through a period of restructuring and change to meet the challenges of the mining industry. DuPont Fasloc has become Fasloc, Inc., a stand-alone company. Celtite became Fosroc then Minova, as it is known today. During this transformation, several manufacturers have either discontinued production or were absorbed. The industry led the development of the chemical grouting materials specifications contained in ASTM F432-95, Standard Specifications for Roof and Rock Bolts and Accessories. A history of the industry will be presented within a discussion of the evolution of the strength index, speed index, cartridge volume, class designation, and product marking requirements of ASTM F432-95.

Jan 1, 2006

By Jamal Rostami, Mark Board, Clayr Alexander, Muthu Vinayak Thyagarajan

In the past several decades, many major equipment manufacturers have ventured into developing new technology for underground hard rock excavation. This includes variety of configurations for full and partial face mobile excavation units. Mining industry prefers machines that can excavate noncircular, flat invert profiles and be able to make tight turns in hard rock. The need to use disc cutters for cutting hard rock has impeded the development of such machines due to the need for gripper system or large mass of a machine to support the force requirements of the disc cutters. Most of the prior attempts have been partially successful and the operations have faced some practical limits and challenges. Among the units that have been successfully used, one can name mobile miner, which was used for rock excavation in some projects. A redesigned mobile miner, called the “Remote Vein Miner,” or RVM, has been developed by Epiroc for underground hard rock mining in Hecla’s Lucky Friday Mine. This equipment potentially opens numerous opportunities for innovation in civil tunneling projects, where the operational flexibility and accessibility of a TBM’s limited tunnel path, design of the profile, and cost are limiting factors. This paper explores the application of the RVM in tunneling projects, its advantages and possible areas of innovation in tunnel planning and design.

Jun 13, 2021

By Asfa-Wossen L.

Davy saw science to be the ultimate truth. He loved the utility and permanence of it and the feeling of progression. He was a bold chemist and an inventor, but he thought like a writer

Feb 1, 2015

Konkola No 3 shaft experienced severe mining-induced stress and time-related deterioration in ground conditions in an area where an over-cut and bench (OCB) mining method was used to extract a shallow dipping wide orebody. This caused an unacceptable risk for safe mining operations to sustain the required levels of production. After a review of the conditions it was decided to change the mining method to CASCADE to recover ore in the affected area and modify the OCB method and use a modified over-cut and bench method (MOCB) for new mining sections. This paper describes the geotechnical criteria included to derive the mining standards for the MOCB. The geotechnical risks are identified and taken into account to develop stope design parameters, stoping sequences and support requirements. A monitoring programme to assess conditions as mining progresses is also discussed.

Jan 1, 2005

By Bryan Ulrich

On March 20, 2014, the ?Roundtable Discussion on Innovations in Heap Leaching and Mine Waste Management? was hosted by Knight Piésold and Co. at the Red Lion Hotel in Elko, NV. This topic is timely, and formed something of a lead into the inaugural ?Workshop on Innovations in Waste Rock, Tails and Heap Leach Management.? That workshop, which grew from the 2013 Elko Roundtable, was held on the University of Nevada, Reno (UNR) campus on May 19, 2014. The workshop was hosted by UNR and the University of British Columbia. Knight Piésold?s local representatives, Bryan Ulrich and Logan Jensen, were joined by Tom Kerr, president of Knight Piésold?s, U.S. practice; Rick Frechette, senior vice president, environmental services and Jeff Coffin, geotechnical engineer, from the Denver, CO office for the roundtable event. The event played host to about two dozen attendees from several western states.

By Alberto Pool

El azufre es un elemento no metálico que proviene de yacimientos que lo contienen al estado nativo. En ese sentido, el presente texto revisa los diferentes yacimientos nacionales de azufre, tipos y composiciones. Dichos yacimientos se dividen en volcánicos (tipo solfatárico) y sedimentarios (tipo yeso). Los primeros se encuentran asociados a cráteres, laderas y fumarolas de volcanes, y los segundos, se encuentran asociados a yeso, caliza y calcita, sin conexión con procesos volcánicos.

Jan 1, 1977

By J. C. Agarwal

A significant portion of the, coal mined by U. S. Steel is beneficiated to upgrade the quality of the resultant coke to meet blast-furnace requirements. Primarily because of degradation from modern mechanized mining methods, a considerable quantity of the coal to be beneficiated is in the 1/4-inch by 100-mesh size range. In the cleaning plants, this coal is usually cleaned on concentrating tables and then mechanically dewatered in solid-bowl centrifuges to 9 to 14 percent water. At some plants, to further decrease the amount of water shipped with coal, and to improve the coking characteristics of the coal at its destination, mechanical dewatering is followed by thermal drying. At U. S. Steel's-Alpheus preparation plant at Gary, West Virginia, approximately 50 percent of the total coal produced is in this fine size range, and two fluidized-bed dryers are used for the thermal drying step. The two fluidized-bed dryers are 14 feet in diameter and were designed by the Dorr-Oliver Company. Although the original design called for a rate of drying equivalent to 37 tons, of moisture per hour, presently they are removing twice that amount. This paper describes, the major problems encountered' in operating these dryers at the present, high capacities and how they were overcome.

Jan 1, 1963

By W. F. Watts

This report describes a statistical analysis of 41,502 respirable quartz dust samples collected from 1974 through 1981 in metal and nonmetal mines and mills. The goal of this Bureau of Mines study was to identify commodities and occupations associated with high quartz dust exposure so that future enforcement and research activity can be focused on the high-exposure areas. For this analysis, the Bureau used its computerized Mine Inspection Data Analysis System (MIDAS), which contains data on nearly 350,000 air samples, including data for 61 contaminants in 45 commodities. The samples analyzed were collected by inspectors of the Mine Safety and Health Administration (MS HA). The data were entered into the MIDAS computer and coded according to commodity, occupation, location, and other categorical information. Occupations an. commodities with high quartz dust exposure were identified by grouping the data by code categories. Workers at sandstone, clay and shale, and miscellaneous nonmetallic mineral mills had the highest quartz dust exposures. Within these mills, occupations with high exposures were baggers, general laborers, and persons involved in crushing, grinding, and sizing operations. Dust concentrations in these mills were not necessarily the highest, but because the dust contained a high percentage of quartz, the health risk from dust exposure was the greatest.

Jan 1, 1984

By W. R. Hail

A proactive design and construct approach was used to remediate the Warm Springs Ponds Complex near Anaconda, Montana under "Superfund". The pond complex is used for treatment/settlement of heavy metals and is a repository for 19,000,000 cubic yards of tailings, precipitates and associated sediments. Remediation has resulted in treatment/settling capacity for flows up to the 100-year flood (3,300 cfs); expansion from 5 to 11 ponds in series requiring 12.5 miles of new or improved embankments with associated hydraulic structures; flood protection for the 0.5 Probable Maximum -Flood (PMF) (70,000 cfs); and closure of exposed tailings along with aquatic and terrestrial habitat enhancement.

Jan 1, 1995

By T. R. Ellis

A number of important international events took place in 2001 in the development and evolution of mineral valuation standards internationally. In Canada, the CIMVal Committee released a draft discussion paper for public and industry comment on principles to guide the development of the planned Canadian mineral-property valuation standard. The International Accounting Standards Board (IASB) received comments on its Extractive Industries Issues Paper. IASB will decide whether the financial statements of public mining and petroleum companies will be allowed to provide the value of mineral and petroleum assets on a current value basis instead of an historic cost basis. The author led the Extractive Industries Task Force of the International Valuation Standards Committee (IVSC) in developing its submission to IASB. IVSC intends to develop an extractive-industries valuation section for its International Valuation Standards, which could support the planned IASB standard. In Australia, AusIMM has carried out an in-depth review of its highly regarded VALMIN Code. The AusIMM's MICA subdivision organized the VALMIN `01 Conference in Sydney, Australia, with a range of international and current issues papers published in the VALMIN '01 book. Considerable support for the IVSC initiative was evident at this conference. The results of the review of the extractive industries submissions to the IASB were expected to be released in early 2002. The CMMI Congress in Cairns, Australia in May 2002 is likely to prove to be an important forum for continued discussion of the development and implementation of international standards and qualifications for mineral valuation. The outcomes and implications of these events are discussed.

Jan 1, 2003

Ammonium nitrate-fuel oil (ANFO) explosives are unstable in hot, reactive sulphide-rich ground at Mount Isa. Under certain conditions associated with background heat, moisture, and chemical impurities from natural oxidation, ANFO composites in contact with hot ground disproportionate and the ammonium nitrate can undergo rapid exothermic reactions with sulphide.Reactions can occur in confined charges from prolonged contact with reactive sulphides, or by contamination with sulphide in loading. Partial interaction can result in misfires or premature detonation. Spilt, scattered and unpropagated explosive will undergo further reaction in sulphide-rich environments. ANFO-sulphide interaction is invariably exothermic and causes an irreversible chemical transformation of the ore.The heat generated during reaction may be dissipated, heating the environment, or rapidly accumulated to yield hot spots or areas in excess of 400°C. These can result in forced ignition of bulk sulphide and sustained combustion.Thermal analysis was used to define the critical conditions for ANFO-sulphide interaction and sulphide combustion.The occurrence of incandescent ore is attributed to the thermal interaction between exothermic hydrolysis oxidation, ANFO-sulphide, and combustion processes.Chemical agents and control methods have been developed to prevent ANFO-induced oxidation and combustion.

Jan 1, 1968

By John A. Franklin, Tom C. Palangio, Norbert H. Maerz

WipFrag systems I and II have become the world standard in photoanalysis systems to measure fragmentation. Mines, quarries and excavating contractors can now easily measure blast results and track the progress of optimization efforts. This technology was developed and evolved to allow automatic measurements of the size distribution of patiicles on moving conveyors, in truck boxes and on crusher feeds. Production machinery can now be controlled by photoanalysis results and multiple cameras allow various locations to be monitored by a single system. Blast designs can be monitored on a shot by shot basis. Changes in delay times, explosives, patterns and hole sizes can be quickly evaluated. Along with this measurement capability has come a heightened awareness of the importance of “optimum size” and uniformity of particles for lowest cost production and material handling efficiency. In the past, savings in the “drill / blast” cycle of the operation were sometimes overshadowed by downstream production costs related to fragmentation. Now total production costs can be compared with fragmentation sizes which will immediately show the trend towards optimum size for economical production. No cost reduction program can be complete without this critical information.

Jan 1, 1997

By João Veludo, Eduardo Júlio, Helen D. Robinson, Jesús E. Gómez

"Utilization of micropiles for structural retrofit requires connection of the micropiles to the footings of the existing structure. Almost ten years ago, an experimental research effort was carried out in the US to investigate the magnitude and mechanism of development of the bond strength between micropiles and existing concrete. The study resulted in important conclusions on the mechanism of connection capacity development and provided specific recommendations for practical design of micropile-to-footing connections. In the last five years, the original study was complemented by an intensive experimental effort in Portugal aimed at answering many of the questions still remaining on this topic. This paper is a summary of the knowledge that is presently available on the capacity of micropile-to-existing footing connections. It presents the results and observations of model tests performed in the US and Portugal, as well as some tests from actual construction sites. The paper presents clear evidence that friction may be the most important component of connection capacity. It also presents a clear correlation between confinement and connection capacity.IntroductionUtilization of micropiles for structural retrofit requires connection of the micropiles to the footings of the existing structure. This is often accomplished by drilling through the footing and developing the connection by direct bond between the micropile grout and the existing concrete. Almost ten years ago, an experimental research effort was carried out in the US to investigate the magnitude and mechanism of development of the bond strength between micropiles and existing concrete. Smooth and textured micropile inserts of varying lengths were tested to failure inside pre-drilled holes of varying diameters. That investigation led to several publications (Gomez et al. 2005, Wilder et al. 2005, Cadden 2009) on the mechanism of development of bond strength between micropiles and concrete, which included a chart for preliminary bond value selection depending on the diameter of the hole and texture of the micropile.An intensive testing program was carried out in Portugal in the last five years. The program focused on answering questions posed by the original investigation and on finding the relationship between connection capacity and level of confinement. Both investigations, and especially the testing performed in Portugal, provided an invaluable amount of information on the mechanisms of failure of micropile-to-footing connections. This information should be the basis for development of design procedures that, until now, were not available."

Jan 1, 2015

By H Kim, J Park, J Lee

Silico-ferrite of calcium and aluminium (SFCA) is a bonding phase in the iron ore sinter. The phase transition upon melting of SFCA was investigated with Differential Scanning Calorimetry and Confocal Laser Scanning Microscope. The initial melting of SFCA occurred at 1183.2°C and a massive melting was found at around 1351.1–1358.2°C. A phase transition-melting was investigated at 1476.5–1478.7°C. The liquid phase was composed of immiscible phases. The present results would be utilised to design a new iron ore sinter for better processing performance in a hydrogenenriched ironmaking process.

Jun 19, 2024

By J. M. Musadaidzwa

Skorpion Zinc is located 25 km north-west of the small settlement of Rosh Pinah in southern Namibia. Commissioned in early 2003, Skorpion Zinc became the first mine-to-metal operation to commercially apply a purely hydrometallurgical process route to exploit a zinc oxide orebody. The novel technology, known as The Modified ZincexTM Process patented by Tecnicas Reunidas, comprises sulphuric acid atmospheric leaching, zinc solvent extraction (SX) and electrowinning (EW) to produce London metal exchange (LME) Special high grade (SHG) zinc. Forming the core of the process, the SX step has thrived in its role as a barrier to impurities and also in the upgrading of the pregnant liquor solution (PLS), converting it into a loaded electrolyte (LE) sufficiently rich and pure for EW. Against this successful run, a number of challenges have, however, been encountered in SX due the emergence of upset conditions largely emanating from upstream processes. This paper outlines some of the major deviations that have beset the SX process in its first five years of continuous operation. Impurity excursions, temperature depressions, changes in phase continuity, excess aqueous entrainment, the effect of colloidal silica and the accumulation of rare earth elements on the organic phase will be discussed in detail. Keywords: skorpion zinc, solvent extraction, the Modified ZincexTM Process (MZP) DE2HPA, aqueous entrainment (AE), loaded electrolyte (LE), standard liquid validation (SLV) test, organic continuity, aqueous continuity (AC), electrowinning, colloidal silica, phase disengagement time (PDT), rare earth elements (REE).

Jan 1, 2009

By F. Cappel

Except in a few special cases, it is necessary for solid fuel direct reduction in rotary kilns that iron-bearing materials be charged with a minimum grainsize of approx. 5 mm. For fines not usable in such form, the combination of sintering - as agglomeration step - and direct reduction were investigated. During reduction of sinter in rotary kilns prevail dependencies on sinter quality and varying reaction parameters, owing to the use of different coals, which led to a definite statement as to what quality sinter must have and which coals can be used.

Jan 1, 1983

By C. C. Huang

Rare earth compounds, such as samarium-cobalt compounds and neodymium-icon compounds, are being used more often for the manufacture of permanent magnets, because these materials permit the production of permanent magnets with higher magnetic energy potential than the conventional ferrite magnets. Especially, the recent rapid developments in the field of electronics and electro-technology have demanded an increased production of rare earth magnets. Unlike ferrite, which is typically produced by a wet process, rare earths can be ground and classified either in a wet or dry process. In the past, batch ball mills, through-pass ball mills in circuit with air classifiers, and conventional jet mills were primarily employed for the dry processing. These methods, however, have suffered from the problems, for example, wear and contamination, low product quality In particle size distribution, difficult to adopt inert-gas operation, and high specific energy consumption. In this report, dry processing of rare earth powders will be presented, especially ultrafine grinding with fluidized bed jet mill.

Jan 1, 1993

By C Tapia Cortez, A G. Dempster, R Fradet, S Saydam, T de Roche, R Shishko, J Coulton

Human ventures into space are entering a new phase in which missions formerly driven by government agencies are now being replaced by those led by commercial enterprises – in launch, satellite deployment, resupply of the International Space Station and space tourism. In the not-too-distant future, commercial opportunities will also include the mining of asteroids, comets, the Moon and Mars. This research examines the role of off-Earth mining in a growing space economy. In this investigation, the term ‘mining’ is taken to embrace minerals, ice/water and other in situ resources. As the off-Earth mining initiative could be the engine that drives the space economy, it would be useful to understand what off-Earth mining market conditions and technology requirements are needed for that economy to prosper. These specific elements are studied in the wider context of creating an economy that could ultimately support a sustainable Mars colony. The methodology for developing the model focuses on the extraction of ice from the surface of Mars to produce propellant and water for life support for a possible colony.CITATION:Saydam, S, Shishko, R, Tapia Cortez, C, de Roche, T, Fradet, R, Coulton, J and Dempster, A G, 2015. An integrated economics model for in situ resource utilisation in support of a Mars colony, in Proceedings Third International Future Mining Conference, pp 305–312 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By Grace N. Broderick

U.S. supply and demand data for coal, by States and regions, were tabulated for the years 1960 and 1965. Estimates are provided of State-by-State quantitative data for the coal industry that can be integrated into State and regional energy balances by source, form, and consumer sectors, and used for estimates of interstate and interregional energy flows. The tables give an estimated total supply of coal available for consumption, and also report the distribution of the supply among the major consuming sectors (household and, commercial, industrial, transportation, and electricity generation). To enable comparison of coal data with those for other energy forms, tonnages were converted to British thermal units (Btu). Future energy analysis studies could be facilitated by changes in the categorization of information collected on the coal industry. The data shown are based primarily on Bureau of Mines source material.

Jan 1, 1969