Search Documents

By S. K. Kawatra, J. E. D. McDonald, S. C. Roache

"The formation of geopolymers from mine tailings using cold-bonding processes is known to be possible. Numerous cold-bonding methods exist, but the hydrothermal processes involving high temperatures and pressures in the presence of steam have been found to be the most ideal. This paper presents the results of successful preliminary studies to apply hydrothermal bonding processes to mine tailings agglomerates. Particle-size analysis revealed the particle size of the tailings waste to be 80 percent passing at 35 µm. The compressive strengths of the tailings pellets were shown to increase with time in the curing vessel, closely approaching the 400 lbf of standard iron ore concentrate pellets. These strengths are sufficient to allow use of the tailings pellets as aggregate materials for asphalt and cement. Additional applications may be possible, including reprocessing to extract more valuable materials and usage as agglomerated road-bed materials, backfills for building foundations, and replacements for sand and lime in cement.IntroductionMine tailings are a waste byproduct of ore concentration and are available in large quantities across the world. Despite their abundance, they have received little attention or consideration for beneficial use. One reason is that the chemical nature of the material is not well known. Another factor that has hindered direct usage is the fine particle size. This raises the questions: what is the composition of the tailings, and how can such fine solids be beneficially used? Because the mining industry produces concentrates, the tailings may be treated as concentrates and processed in the same fashion, but it would be inefficient to consider full sintering or induration conditions for materials that have little ore content. To achieve sustainable operation, the development of technologies to use these tailings is necessary. Mine tailings should not be considered waste, and an “out of sight, out of mind” mentality does not represent a sustainable solution for the future.One iron ore mine in Michigan is estimated to have accumulated more than 400 million metric tons of tailings during its last 30 years of operation, with an additional 180 million metric tons accumulated before the ore body is depleted. These mine tailings currently have no practical use, largely due to a scarcity of knowledge of their true physiochemical nature. It is thought that lack of quality control of the waste material prevents its use, but variability in the unprocessed ore prevents a consistent waste stream composition. The fact that the tailings are available in such great quantities makes them an extremely attractive resource. However, developing a sustainable, low-cost means of repurposing the mine tailings waste as a construction material may only be completed once the tailings are physically and chemically understood. Due to the high silica content of the material studied, cold bonding was determined to be the most viable method for processing the tailings into a usable product."

Jan 1, 2016

By Robert E. Wood

Engineers have known for some time that the efficiency of filtering iron ore concentrate slurry can be significantly improved by pre-heating the slurry ahead of the filters. However, heating such large quantities of dense slurry by conventional means has proven to be inefficient and high-maintenance. Recently though, submerged combustion was considered by Altos Hornos de Mexico SA (AHMSA), an integrated steel producer in the state of Coahuila, Mexico, as a means of pre-heating their iron ore concentrate. The company toured many iron ore facilities in Brasil and Labrador, reviewing their heating processes, and concluded that submerged combustion could provide a competitive advantage through operational efficiency and lower capital cost than steam boilers. Inproheat was retained by the company to design and manufacture a SubCom slurry heating system to heat 403 m3/h of iron ore concentrate slurry from 25°C to 60°C. The 60GJ/h SubCom system consists of five natural gas combustion chambers mounted in an iron ore concentrate storage tank. The system features a heat recovery unit whereby the exhaust gases are used to preheat the incoming slurry stream, giving the system an overall thermal efficiency of 95%. As a result, the steel company expects to realise significant improvements in filtering efficiency which will enable them to increase the capacity of their pelletising plant without installing additional filters.

May 1, 2010

By Gerd L. Klinkenborg

Throughout the history of the development of mechanical conveyor systems, it has always been an established condition that loads are received at one end of a single-belt conveyor and discharged at the other end, in a point-to-point, manner. In systems designed for the continuous transport of granular materials, vertical or horizontal changes in; direction have always necessitated two or mope single-belt conveyor units, with a corresponding number of motors, assemblies and attendant mechanical and human or electronic controls. Besides these high-cost factors, every change in the system's direction also calls for a transfer point that involves a drop-back of the material from one level to another with some loss of the material and, in many cases, unwanted additional granulation. Where changes in the location of the discharge point are wanted, the conventional single-belt conveyor must either be replaced by a shorter or longer unit or additional units purchased and installed, or existing units rearranged. This can take days or weeks, and involve special expenditures as well as loss of valuable production time.

Jan 1, 1962

By Dermot M. Ross-Brown

The more important factors controlling the design of pit slopes are related to the local geology over which the designer has little or no control. Nevertheless, there are some factors over which the designer does exert some control and these concern the say in which the rock is excavated and supported. They include blasting, face cleaning, water control, and the use of rock improvement techniques. The paper discusses these factors and relates the extra costs incurred to the steeper slope angles that can usually be obtained. It is demonstrated that even a modest increase in bench angle of 5° through improved excavation techniques can pay off in a single push-back.

Jan 1, 1975

By R. Agius, A. Nacu

"Adoption of the International Cyanide Management Code, regulatory requirements and community concerns have increased the need to implement suitable cyanide destruction processes at gold operations to meet ever more stringent discharge limits. As standards set for the allowable concentrations of cyanide, cyanide compounds and other contaminants may vary from country to country, jurisdiction to jurisdiction, and even from site to site, there is no “one size fits all” technological solution. Currently the most common cyanide destruction processes used in industry are sulfur dioxide/oxygen, hydrogen peroxide and Caro’s acid. Regardless of the process used, cyanide destruction plants must be reliable and achieve permit guidelines at all times. The selection of the most appropriate cyanide destruction process for an operation depends on several factors, including permit discharge requirements, tailings chemistry, location, site-specific climatic conditions and size of the operation. Only after considering all these factors together can the most effective approach be selected to achieve the permit guidelines economically and technically feasible. Finally performing the correct test work program is the most important step to ensure that the correct process design criteria can be determined to accurately calculate capital and operating costs.IntroductionThe adoption of the International Cyanide Management Code in 2005, stricter regulatory requirements and community concerns prompted by environmental incidents involving cyanide have increased the need to implement cyanide destruction processes at gold and silver operations.Process solutions associated with the extraction of gold and silver contain several forms of cyanide. The most toxic form of cyanide is free cyanide, which can be present as a dissociated cyanide anion (CN-) or gaseous or aqueous HCN. Weak or moderately stable cyanide complexes such as those of zinc, copper and nickel are classified as weak acid dissociable (CNWAD). Although less toxic than free cyanide, weak acid dissociable cyanide complexes are considered “ecologically sensitive” forms of cyanide and are regulated in most jurisdictions. In practice, reported WAD cyanide values are comprised of both free cyanide and weak acid dissociable cyanide complexes. Cyanide complexes with gold, mercury, cobalt and iron are referred to as strong acid dissociable complexes (CNSAD) and are much more stable even under mildly acidic conditions. Another term commonly used in cyanide chemistry is total cyanide, which represents all cyanide compounds present in solution, with the exception of cobalt complexes. Total cyanide levels in solutions are in most cases higher than WAD cyanide values and the difference between the two usually indicates the presence of iron-cyanide compounds. Typically, in Canada CNTOTAL levels cannot exceed 1 mg/L in solutions."

Jan 1, 2017

By M. J. Pool, C. E. Lundin

THE relative partial molar enthalpies of aluminum, gallium, and indium in liquid tin have been measured at 750°K by liquid-metal solution calorimetry. The measured heat effects and the calculated relative partial molar heats of solutions at infinite dilution are listed in Table I along with the relative heat contents of the solutes calculated from the data of Kelley. All of the values are referred to 750°K even though the calorimeter temperature fluctuated by +1°K during the entire series of experiments. The effect of this small temperature variation on the experimental values should be less than the experimental error. The limits of error given in Table I represent the standard deviations of all values from the mean. In no case was the experimental deviation greater than the listed error limits. The reported error estimates only apply to the estimated precision of experimental values and not to their accuracy. Systematic errors could be present in the calorimeter which would affect the absolute values given. Moreover the heat-content data used could also be in error and this would affect the end results. The relative enthalpies used were listed in Table I so that future corrections could be made if necessary. The relative partial molar heats of solutions of aluminum in liquid tin and dilute A1-Sn liquid solutions are large and positive. The value at infinite dilution is given in Table I. In the dilute-solution region investigated the relative partial molar heat of solution was a linear function of composition. A least-squares analysis of the data gave the following expression at 750°K: Atf^ = 6195 - 12,160 A:A1(cal/g-atom) where XA1 is the mole fraction of aluminum in the alloy. This can be compared with the data of Cohen, Howlett, and ever' who obtained the expression: 1SM = 6075 - 10,750 XM at 573°K Apparently both the partial molar heat of solution at infinite dilution and the concentration dependence increase with increasing temperature. This same

Jan 1, 1964

By H. F. Yancey

This report, dealing with the separation of coal from its associated impurities by means of a pulsater-type jig, continues the series of reports that have been issued by the Bureau of Mines, in which detailed study has been made of the efficiency and mechanism of separating coal and impurities in various coal-cleaning appliances. The previous reports have dealt with the piston jig, coal-washing table, pneumatic table, and Baum-type jig. Such studies of the separation accomplished by any form of concentration device are essential and necessarily preliminary to any intelligent attempt to improve the performance of such equipment Object and Plan The pulsator-type jig was developed recently by G. A. Vissac. Although two articles(2) describing plants using this typo of cleaning unit appeared in 1936, both dealt principally with plant design and layout rather than with plant performance The object of the stork described in this report was to determine the efficiency of the separation made by the pulsator jig on a sized feed, the specific gravity at which the separation between coal and impurity was effected, and the influence of the specific-gravity composition of the coal on the character of the separation made.

Jan 1, 1938

By H. F. Yancey

This report, dealing with the separation of coal from its associated impurities by means of a pulsator-type jig, continues the series of reports that have been issued by the Bureau of Mines, in which detailed study has been made of the efficiency and mechanism of separating coal and impurities in various coal-cleaning appliances. The previous reports have dealt with the piston jig, coal-washing table, pneumatic table, and Baum-type jig.5/ Such studies of the separation accomplished by any form of concentration device are essential and necessarily preliminary to any intelligent attempt to improve the performance of such equipment Object and Plan The pulsator-type jig was developed recently by G. A. Vissac. Although two articles(2) describing plants using this type of cleaning unit appeared in 1936, both dealt principally with plant design and layout rather than with plant performance The object of the stork described in this report was to determine the efficiency of the separation made by the pulsator jig on a sized feed, the specific gravity at which the separation between coal and impurity was effected, and the influence of the specific-gravity composition of the coal on the character of the separation made.

Jan 1, 1938

By Jewel A. G. Gomes

Electrocoagulation (EC) has been performed with Al-Fe electrode system with changing polarity for the removal of arsenic from water. The removal process has been studied using ICP-AES and Anodic Stripping Voltammetry with a wide range of arsenic concentration (1-1000 ppm) at various pH (4-10) and residence times (1-60 min). Electrochemically generated by-products have been analyzed using XRD, FTIR, XPS, SEM/EDS and Mössbauer Spectroscopy. Results revealed expected crystalline iron oxides (magnetite (Fe3O4), lepidocrocite (FeO(OH)), iron oxide (FeO)) and aluminum oxides (bayerite (Al(OH)3), diaspore (AlO(OH)), mansfieldite (AlAsO4?2(H2O)), as well as some interaction between the phases. The amorphous or ultra-fine particular phase was also found in the floc. The substitution of Fe3+ ions by Al3+ ions in the solid surface has been observed, indicating an alternative removal mechanism of arsenic in these metal hydroxides and oxyhydroxides by providing larger surface area for arsenic adsorption via retarding the crystalline formation of iron oxides.

Jan 1, 2006

By Amir Karami, Scott Munro

This paper focuses on remediation of a 3.6 km long water conveyance tunnel that suffered two large falls of ground (FoGs), one of which subsequently progressed to the ground surface, resulting in full collapse of the tunnel. The tunnel is part of a network of water conveyance tunnels and open channels that direct water into two turbines located in an underground powerhouse, originally constructed in the 1970s. At the time of construction, the tunnel was partially supported with shotcrete or rock bolts, with no further ground support added since construction. Two sonar surveys in 019 and 01 identied two adacent large FoGs in the tunnel, approimately 1.2 km from the tunnel outlet. Historical geological and geotechnical information indicated that the FoGs occurred within a 60 m wide fault zone. Remediation plans were developed, which included stabilization of the outlet channel, the portal, the tunnel leading up to the FoG areas (1.2 km length) and the FoG areas. Several remediation options were considered to restore the tunnel, including construction of a diversion tunnel to bypass the FoGs or remediation of the FoG areas with steel ribs and backlling the void above the FoGs to surface.

Jun 23, 2024

By Donald P. Tuchman, Robert P. Vinson, Jon C. Volkwein

Research by the National Institute for Occupational Safety and Health (NIOSH) has pursued quartz analysis for the specialized ?lter assemblies of a new worker-wearable personal dust monitor (PDM). The PDM is a real-time instrument utilizing a tapered element oscillating microbalance (TEOM®). Standard ?berglass TEOM ?lters cannot accommodate the desired P-7 infrared analytical method used by the Mine Safety and Health Administration (MSHA). Novel ?lter materials were tested with the objective of demonstrating this type of analysis. Low temperature ashing and spectrometric examination were employed, revealing that nylon ?ber candidate ?lters left minimal residual ash and produced no signi?cant spectral interference. Avoiding titanium dioxide in all ?lter materials proved to be a key requirement. Fine quartz particulates were collected on prototype ?lters in a Marple chamber, either open-faced or through PDMs during test runs. The ?lters were then subjected to MSHA P-7 analysis and the spectrometrically based analytical results for quartz mass were compared to reference measurements. Also, PDM instrumental mass readings were compared to ?lter gravimetric measurements. Results suggest that the P-7 method is adaptable to variations in ?lter materials and that quartz dust analysis by the P-7 method when utilizing the new ashable PDM ?lters can have accuracy and precision within 10% and 4%, respectively. This is within the declared 13% accuracy and 7–10% precision of the P-7 method itself. Instrument mass readings had modest positive bias but met NIOSH accuracy criteria. Continued work with specialized PDM ?lters is merited, as they are a new type of TEOM sample amenable to ashing analysis of particulates.

By C. G. Storm

Permissible explosives are those that have passed the tests pre- scribed by the Bureau of Mines for explosives intended for use in coal mines, and are therefore recommended by the bureau as suitable for this class of work when used under the prescribed conditions. The tests for permissible explosives and the conditions prescribed for their use are described in Miners' Circular 6 of the Bureau of Mines. Up to June 1, 1915, 168 explosives had been classed as per- missible explosives; 133 of them were then on the bureau's "per- missible list" and 35 had been withdrawn by the manufacturers. In addition to the required physical tests, each explosive is sub- jected to a complete chemical examination in order that its exact composition may be known and also that the composition of future samples of the same explosive collected in the field may be compared with that of the sample which originally passed the bureau's tests, for by such comparison it may be possible to ascertain whether or not the explosive as supplied to the miner is still "permissible." This bulletin is published primarily for the purpose of informing manufacturers of such explosives as to the methods used by the Bureau of Mines in the analysis of samples received for tests to determine their permissibility. Such information may be of value in cases of possible controversy over the results obtained in the analysis of a field sample as compared with those obtained in ana- lyzing the sample originally tested by the bureau. Also, a descrip- tion of the methods used by the Bureau of Mines in the analysis of explosives should be of assistance to the many chemists engaged in similar analytical work.

Jan 1, 1916

By K. V. Raj, C. A. Berry, A. T. Weakley, A. L. Miller, P. R. Griffiths, D. A. Parks

Diesel particulate matter (DPM) has been classified as a carcinogen to humans by the International Agency for Research on Cancer. As a result of its potential carcinogenic nature, DPM exposure is regulated by the Mine Safety and Health Administration. Currently, diesel emissions in the workplace are monitored by collecting the aerosol onto filters, which are then sent to a laboratory for thermal-optical analysis using the NIOSH method 5040. This process can take days or even weeks, and workers can potentially be exposed to excessive levels of DPM before the problem is identified. Moreover, the delay involved in getting the loaded filter to the lab inevitably means the loss of some of the more volatile organic carbon. To remedy this delay, researchers from the National Institute for Occupational Safety and Health are seeking to develop a field-portable, real-time method for measuring elemental and organic carbons in DPM aerosols. In the current study, the use of mid-infrared spectrometry was investigated. It is believed that mid-infrared spectroscopy is more suitable for use in a real-time field-portable device than thermo-optical analysis methods. This article presents a method for measuring organic carbon (OC) and elemental carbon (EC) in DPM for a broad range of OC/EC ratios. The method has been successfully applied to laboratory-generated and mine samples.

By R M. Yanamandra, M Kumar, S K. Tripathy, N Mangadoddy, P Sudikondala

Spiral concentrators are one of the flowing film gravity concentration devices used to beneficiate coal and mineral ores. The aim of the current study is to understand the particulate flow and separation performance of an LD9 spiral concentrator using a multi-phase Computational Fluid Dynamics (CFD) model. The CFD model utilises the Algebraic slip mixture model to simulate particulate flows. The model employs the Renormalisation group (RNG) k-ɛ turbulence models to resolve the fluid turbulence. Initially, the volume of fluid method was adopted to track the water-air interface. Simulations were then carried out at low (0.3 and 3 wt.%) and moderate (15 wt.%) solids concentrations. Multiple particle-phase representing particles of poly sizes (75–1400 µm) and multi-densities (1450–2650 kg/m3 ) were simulated to study the particle segregation on the spiral trough surface. The numerical predictions are compared with the literature performance data at a diluted pulp flow rate of 6 m3 /hr. The results were found in close agreement. Further, the same CFD model is used to study the change in pulp velocity, streamflow rates, and separation performance at increasing solids concentration. For the same density particles, Fine particles mostly show higher volume concentration in the middle and outer trough regions, whereas coarse particles show higher volume concentration in the interior and central trough regions. It implies that the fine particles mostly segregate towards the outer region, and dense particles segregate towards the axial column.

Aug 24, 2022

By T. Mudder, R. Cellan, R. Waterland, J. Whitlock, B. N. Nelson

The effectiveness of anaerobic in-situ biological treatment for the immobilization of selenium, molybdenum, and uranium in an alluvial aquifer was examined using long-term column tests. A series of organic substrate and nutrient combinations were tested to determine removal effectiveness, optimum supplement concentrations and ratios. Final column testing was conducted to determine the chemical stability of the treatment by-products/treatment compounds by dosing the columns continuously with elevated redox untreated alluvial groundwater.

Jan 1, 2002

By J. T. Ryan

SAFETY practice or the elimination of accidents in our coal mines is specifically a problem of management. It cannot be delegated to any governmental agency except that the various coal-producing states do and should have some minimum safety standard laws. However, the legislative method of attempting to control mine accidents is ineffective because of the delay between the necessity and the action. It will always be impossible to keep our various state mining laws up to date; and when the law says you must do a certain thin there is a tendency to do this and no more. Unless the scheme for setting up state regulations is so flexible that when a new hazard develops it can be immediately and adequately covered and the whole responsibility for accident elimination placed undivided on the

Jan 1, 1937

By Zhihe Dou, Yan Li, Qiuyue Zhao, Guozhi Lv, Yan Liu, Hongliang Zhao

"Abstract: How to reduce carbon dioxide emissions has become a vexing problem, meanwhile, there exist high energy consumption and low efficiency problems in the existing CO2 capture and storage technologies. For CO2 comprehensive Utilization, this paper researches a new technology of absorbing the CO2 emission with high alkaline calcium or high alkaline wastewater sludge mineralization of calcium and invent a core device for multi-level jet carbonation. The industrial test has been carried out in China Xinyu slag Engineering Co., Ltd. The wastewater flow is 150m3/h in the pilot scale. The prepared calcium carbonate has a whiteness greater than 90%, particle size less than 150nm. The mineralization of aluminum exhaust with waste carbide indicates that the CO2 absorption rate is greater than 99.0%, CO2 concentration in the exhaust gas is lower than 0.08%, the purity of mineralized calcium carbonate is greater than 99.0% and particle size is less than 100 nm.InstructionAccording to the statistic data from IEA (2009), the carbon dioxide discharge from fossil fuel consumption in China has exceeded it in the US by the year of 2007, China, has become the largest emitter of carbon dioxide all over the world. Meanwhile, the economic scale is still on an increasing trend in the next 50-100 years, leading to a continuous increment in carbon dioxide discharge. According to the international energy agency forecasts, the energy-relative CO2 discharge in China will rise to 11,615 million tons, 91.3% higher than it in 2007. In the year of 2012, the CO2 gross discharge has reached 10,000 million tons, obviously higher than the predicted value. It is a tremendous task to reduce the emission. Non-ferrous metals industry is one of the largest emitters of carbon dioxide among the industrial circle, the whole industry might discharge a huge amount of carbon dioxide (over 600 million tons), in which the electrolytic aluminum industry is the largest energy consuming industry and CO2 emitter. At present, the CO2 discharge has focused by the whole world due to the environmental problems it causes; meanwhile, supplement of new carbon source is needed due to the exhausting oil and coal resources, so that various countries in the world are attaching importance of the recycle and purification of CO2. Many countries are studying on the cyclic utilization of carbon dioxide. Gas CO2 is mainly applied in chemical, pharmaceutical raw materials, beverage filling agent, refrigerant, inert medium, solvents, pressure source, the welding protective gas, antioxidant and fire extinguishing agent, etc. Solid CO2 is mainly applied in penicillin production, fish, cream, ice cream and other food storage and transportation at low temperature, etc. nowadays, such methods as absorption method, membrane separation, adsorption, etc. are widely used to recycle CO2, with such problems as high investment cost and technical constraints etc."

Jan 1, 2014

By D. B. Dreisinger, V. van der Pas

Zinc sulphate electrolyte used for zinc electrowinning must be purified for cObalt ions. The cobalt is removed in a cementation stage by the addition of zinc dust. Copper arid antimony are frequently used additives which enhance the cementation of cobalt. This paper aims at a better understanding of how copper and antimony promote the removal of cobalt. Initial experiments were done in a batch cementation reactor. Copper and antimony precipitated in the early stages of cementation indicating that a preferential substrate was formed. The individual role of copper and antimony was further investigated in an electrochemical cell. On a microsca1e, the , growth process, morphology and the composition of the precipitates were examined with SEM and XRD. It was found that cobalt could not be deposited in its pure form but as a cobalt-zinc alloy with zinc as the prime constituent. Copper increases the cathodic surface area of zinc dust by precipitating as numerous dendrites. Antimony acts as a cathodic surface onto which a cobalt-zinc alloy with an increased cobalt content is deposited.

Jan 1, 1997

By Donald E. Raab, Lee W. Saperstein

INTRODUCTION The Premise Not much time has to be spent in a tunneling project to realize the tremendous interdependence that exists among the various unit operations. The research that is to be described attempts to examine one set of these linked operations, namely, the effect of cutters on muck handling properties. All too often research focuses on too minute an aspect of a problem for the results to be of much immediate, practical use. The goal of this research is to avoid this specificity. Apologies are tendered if this goal is missed. It is known that the mode of flow of bulk solids under the influence of gravity -- emptying a bin or hopper -- is dependent on several basic parameters. The size of the particles and the distribution of sizes (consist) determine whether the solids will first flow out of a given aperture; the cohesion of the solids will determine if flow will continue after the bin is opened; and the angle of internal friction determines the size of the flow regime (1,2,3). It is well understood that the latter two parameters affect the behavior of bulk material on a conveyor belt. Cohesion of material to a belt is always an undesired problem. Heaping of material on a belt depends on the material's internal friction. It is also known that varying the particle size, and the packing density of the material can affect the material's angle of internal friction (4,5). The question was posed whether sufficient variation in a mechanical tunneling machine's (mole) cutting function could be arranged to affect materially the handling properties of the muck

Jan 1, 1974

By G. Akdogan, Q. G. Reynolds, S. J. Baumgartner

A computational model of a submerged arc furnace (SAF) used in the production of ferrochrome is presented. The model‘s intended use is to investigate the extent to which intrinsic and extrinsic properties of the raw materials affect burden distribution and electrical resistance within the furnace. The model is built on the discrete element method and calculates the mechanical interactions of particle distributions resulting from the flow motion of typical raw materials used in the smelting of chromium ore. This model excludes the effects of thermodynamics, furnace chemistry, and heat transfer. It illustrates how the consumption of materials (chromite pellets, flux, and reductant) is affected by changes in electrode length, reductant fractions, and reductant sizing and density during the formation of a reductant bed. The resistance calculation algorithm developed by Mintek was applied to construct networks developed from particle contacts, which can quantitatively generate estimates of the electrode-to-electrode and electrode-to-bath electrical conduction conditions.

Apr 16, 2024