Search Documents

By V. E. Edlund

This report presents the results obtained in a study of the technical feasibility of recovering a usable pig iron by pyrometallurgical treatment of typical copper reverberatory slags . The iron in the slag was readily reduced with carbon , but the copper and sulfur content of the metal was best controlled by a three - stage procedure comprising ( 1 ) melting the slag with pyrite to remove copper as a low- grade matte , ( 2 ) smelting the partly decopperized slag with fluxes and carbon to reduce the iron , and ( 3 ) refining the impure iron alloy from step 2 with a flush slag to remove sulfur and residual copper . Laboratory - scale tests demonstrated that washing with 8 wt pct of pyrite lowered the copper content of a typical reverberatory slag from 0.58 to 0.12 Subsequent smelting of a mixture composed of 70 pct decopperized slag , 25 pct lime , and 5 pct coke reduced 84 pct of the iron to metal containing 2.27 pct sulfur . This metal then was successfully desulfurized by treatment with a basic flush slag to produce a finished metal that contained , in percent , 93.5 Fe , 0.02 S , 0.26 Cu , and 4.9 C. Overall recovery of iron under the conditions of trial was about 80 pct . This could be increased if higher tolerances for copper could be accepted . Commercial processing would be accomplished in three furnaces with molten materials passing from one to another . Currently produced smelter slag could be treated fairly inexpensively , because the molten product would require only a little additional heat to produce an iron byproduct that undoubtedly would be attractive to local foundries .

Jan 1, 1964

By L. O. Bacon, H. R. Joesting, J. H. Getz

"INTRODUCTION For a number of years manganiferous iron ore has been mined on a small scale at Boston Hill, in Grant County, N. Mex. Total production up to 1943 is estimated to be over 793,000 long tons, containing 8 to 35 percent manganese and 26 to 46 percent iron. 4/ During 1941 to 1943 production was estimated to be 206,000 long tons, containing about 13 percent manganese and 37 percent iron. During 1944 daily production was several hundred tons, mostly from a single open pit. Several moderately large deposits have been mined: and many smaller ones have been found.From February to April 1945 geophysical surveys were carried out on Boston Hill by the Division of Geophysical Exploration, in cooperation with District 5, Central Region, Bureau of Mines, to determine if hitherto undiscovered manganiferous iron deposits exist. Field work was interrupted for a total of about 1 month during this period by work on other projects in nearby areas. Previous to the geophysical surveys, a preliminary examination was made by H. R. Joesting to determine if geophysical methods could be utilized in exploring the area. 5/Field measurements were made by L. O. Bacon and J. H. Getz, project geo¬physicists of the Bureau of Mines, under the general supervision of H. R. Joesting. A grid survey of the area, to locate geophysical stations, was made by Paul Russell, Bureau of Mines engineer, who also collected specimens for laboratory tests. Most of the computations and the preliminary magnetic and resistivity maps were made by L. 0. Bacon."

Feb 1, 1948

By Yuanbo Zhang, Zijian Su, Bingbing Liu, Guanghui Li, Jicheng Liu, Manman Lu, Tao Jiang

Blast furnace slag (BFS), one kind of typical solid waste in the steel industry, was used as structural materials to synthesize NaNO3/BFS composite phase change materials (C-PCMs) by mixing and sintering method. NaNO3 in the composites functioned as phase change materials (PCMs) and BFS as structural skeleton to maintain a stable external form. In this study, the prepared C-PCMs could remain in the solid state without salt leakage even if operating temperature exceeded the melting temperature of NaNO3. The composition and structure of BFS and the prepared composites were characterized by XRD, FTIR, SEM and TG-DSC analyses. The results showed that NaNO3 was well incorporated in the pores of BFS. The melting temperature and latent heat of the final composites were 300.5 °C and 65.53 J/g, respectively. The product also had good thermal storage performance and durability even after 100 thermal cycles. The energy density of the product was calculated as high as 468.03 J/g for an temperature range of 50–400 °C.

Mar 1, 2018

By Mahmut Altiner

In the present study, the use of horse residue as an alternative reducing agent in the roasting of a low-grade goethite ore containing 17.60% Fe was investigated. Additional roasting experiments were carried out with corn starch and without reducing agent for comparison. Each roasted product was characterized using X-ray diffraction (XRD) and magnetic hysteresis (MH) loops analyses. The optimum roasting conditions (roasting temperature [400, 500, and 600 °C], reducing agent/ore ratio [0.04, 0.08, and 0.12], and roasting time [10, 20, and 30 min]) were investigated based on the Taguchi approach. The magnetic susceptibilities of the roasted sample with the addition of reducing agents were higher compared to that of the roasted sample in the absence of reducing agent. Experimental findings indicate that the horse residue can be used as the reducing agent. Finally, an iron ore concentrate assaying a Fe grade of 62.12% with a recovery of 56.93% was prepared using wet magnetic separation at a magnetic intensity of 0.5 T from the ore roasted under the following roasting conditions: roasting temperature of 500 °C, reducing agent/ sample ratio of 0.08, and roasting time of 30 min.

Jun 3, 2020

By N. B. Prenn

Many recent projects have been developed and mined based upon imaginary reserves. Imaginary or "geo-fantasy" reserves have cost many companies millions of dollars. The significant and varied technological advances in the mining arena have done little to curb reserve calculation problems. These advances may have served to increase the prevalence of reserve problems by putting more tools in the hands of personnel not properly trained or experienced in reserve estimation. This paper will discuss potential problems related to calculating reserves, which include: SAMPLING ERRORS -obtaining a representative sample. -Decay analysis of wet RC drilling -Bias introduced by sample preparation. -Assay bias; Coarse gold. -Specific gravity samples. GEOLOGICAL ERRORS -structural boundary definition. -Separation of high grade and low grade zones. -Incorrect continuity assumptions MODELING ERRORS -Too much influence of high grade samples. -Improper method of calculation. -Assumed range of influence. -Errors in the data. ENGINEERING ERRORS -Inaccurate assumptions. -Inadequate metallurgical testing. -Designed bottlenecks.

Jan 1, 1992

By Omar A. Muhtadi, R. Bruce Thorndycraft, David A. Milligan

9.1 INTRODUCTION Precious metals in a leach solution are extracted, concentrated, and purified to complete the process begun in the heap and to produce an end product which will provide an economic payback to the mine developer/operator. Several different processes are required to convert the dissolved precious metals into pure metal bars. This chapter discusses the actual production of metal once it has been recovered from the pregnant leach solutions by the zinc cementation (Merrill -Crowe) or carbon adsorption processes. Metal production is generally taken to mean the production of a fairly pure "dore" bar. This chapter also reiterates some information from Chapter 8 in a slightly different context, since the focus of Chapter 8 was a fairly detailed description of the two actual recovery processes, whereas the focus of this chapter is metal production. The sale of an intermediate precious metal product is possible (as opposed to the production of dore bars at the mine site); however, the value of the precious metals is reduced by the various charges and risks associated with precious metal processing. For this reason, most operators choose to produce the most refined metal possible in order to maximize project economics. Precious metals may be extracted from the leach solution by both conventional and unconventional processes. The conventional processes are activated carbon/electrowinning (ACE) and zinc precipitation (ZIP). The unconventional processes are resin ion exchange, solvent extraction, and direct electrowinning. A typical ACE process has two circulating loops. The first loop adsorbs the cyanide-metal complexes from the dilute leach solution onto the activated carbon. A second, separate solution loop removes the cyanide-metal complexes from the activated carbon into a strong solution, the electrowinning electrolyte. Activated carbon is transferred from one fluid loop to the other. The operating cost of the ACE process is directly proportional to the quantity of carbon stripped and thus to the quantity of precious metal produced. A typical ZIP process contains a single circulating loop. The solution is filtered, deaerated, contacted with zinc, and filtered again. The barren leach solution is then returned to the heap. The zinc sludge recovered in the

Jan 1, 1988

By J. R. Thoenen

During 1928 questionnaires covering the calendar year 1927 were sent to over 1700 quarries: producing stone for purposes other thaw cutting to dimension. These inclined producers of stone for limn burning; cement manufacture, rip rag, and crushed stone. The various rinds of stone represented were limestone, trap rock, sandstone, granite, and marble. Replies received from limestone producers prior to November, 1928, were compiled into tables and published in February, 1925, as a preliminary report (Bureau of Mines Report of Investigation 2911).

Jan 1, 1930

By Louis C. Britcha

"The Phelps lease in Jasper County, Missouri, was first examined by the Bureau of Mines3/ in December 1943, at the request of Thomas Phelps of Joplin, the lessee. Owing to urgent war requirements for zinc and lead and evidence of favorable geological conditions and past productivity of adjoining properties, it,considered justifiable to explore for extensions of known ore deposits and possible undiscovered ones. In August 1944, funds were allotted for this work, which was started January 5, 1945, under the direction of the author.The provision of facilities and storage space on the property by the lessee during drilling operations is gratefully acknowledged.The Phelps lease is on land belonging to the Rex Mining & Smelting Co. It lies immediately southeast of the city limits of Joplin, Mo. It may be reached by going cast from Joplin on paved 20th street to half a mile beyond Range Line road. Twentieth street is the northern boundary line of the property, which consists of approximately 145 acres and includes the W 1/2, NE1/4, and all of the E ½. NW1/4 except 15 acres along the west side of that quarter section, of sec. 18, T. 27 N., R. 32 W., as shown on figure 1.The property is part of a 1,000-acre tract owned by the Rex Mining & Smelting Co., Paul D. Porter, president, Joplin, Mo. The lease was acquired by Thomas Phelps of Joplin, in 1937. At present the lease is controlled by a recently formed association known as the Eureka Products Co., Charles W. Madison, manager, Kansas City, Mo.Dependable skilled mine labor is scarce in the district at present, but there seems to be enough transient mine labor for small operations. The prevailing wages of the district run from 55 cents to 95 cents per hour for various types of mine labor.Living accommodations and markets to supply all domestic requirements are available in Joplin.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the and that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director."

Jul 1, 1946

By Bruno Santos Malaquias, Carlos Eduardo Pessoa Gomes, Diego Canez Fernandes, Henriquison Magela Bottrel Reis

A formação de depósito de carbono é inerente ao processo de coqueificação, com tendência a se acumular nas regiões da zona livre do forno (teto, boca de carregamento e paredes) e no tubo de ascensão dos gases. Contudo, o depósito quando em excesso, se não for removido a tempo, pode causar queda na produtividade, além de impactos ambientais e redução da vida útil da coqueria. Neste contexto, foram avaliados os mecanismos de formação de depósito de carbono, bem como os fatores relacionados ao processo de coqueificação e da mistura de carvões. Foi realizada uma análise estatística dos dados da coqueria, para identificar as principais variáveis que influenciam a formação do depósito de carbono. Em paralelo, foram avaliadas amostras coletadas nas regiões da boca de carregamento, no tubo de ascensão dos gases e do MIQ de alcatrão. Verificou-se que as amostras são formadas por partículas de carbono pirolítico (craqueamento do gás) e majoritariamente pelas partículas carreadas, correspondendo a 60%, 54% e 72%, respectivamente para as regiões da boca de carregamento, da base do tubo de ascensão e superior do tubo. Foram identificadas e sugeridas ações visando minimizar a formação de depósito de carbono, tais como: redução da temperatura da zona livre; aumento da densidade da carga; controle da fração superfina (< 0,105 mm); redução do teor de matéria volátil da mistura de carvões e uso de técnicas de descarbonização.

Oct 1, 2019

By Neville Rockhouse

This paper examines the interrelationship of conducting full risk assessments in the context of the coal mining industry and under the framework of the Health's Safety in Employment Act 1992. In the context of Occupational Health's Safety, Risk Management is a holistic management process that can be used by individuals working in all organisations and from all industries. The Australian New Zealand Standard 4360: 2004 defines a Risk as being; The chance of something happening that will have an impact on objectives. This definition is followed by several notes that include: a risk is often specified in terms of an event or circumstance and the consequences that may flow from it, risk is measured in terms of a combination of the consequences of an event and their likelihood, and risk may have a positive or negative impact. For the purposes of this paper, the above definition will be adopted. This paper examines the newly expanded approach of the fully documented risk management process in the New Zealand coal mining industry. This is done in the context of the coal mining regulations but more importantly by using the framework of the Health & Safety in Employment Act 1992. This legislation under Section 6 requires all employers to, Take all Practicable Steps to prevent harm coming to employees while at work and to others who might be at or in the vicinity of a workplace. When the term 'all practicable steps' is studied, one can clearly see that such steps should be the same steps taken that a prudent and reasonable person would have taken given the same type of circumstance. Due to the fact that in New Zealand parliament made statutes is administered by a Government Department, means that their breaches will be heard before a judge in the District Court. Under the Westminster System of Justice, a basic dictum of that court in matters relating the occupational health and safety is that a breach needs to be satisfied to a specific standard. That standard is, 'Beyond a reasonable Doubt'. One of the primary benefits of adopting a proactive approach to risk management is that if the industry were to adopt similar approaches, then this mythology could be seen as an industry standard. As such, the approach carries the same status in a court of law, as that of an Approved Code of Practice.

Jan 1, 2007

By Kenneth E. Hjelmstad

In situ leach mining operations often encounter difficulty maintaining adequate leach solution flow into the are formation. Swelling and dis-persion of clay particles in the formation are often responsible for this permeability loss. Permeability and leaching tests were done in the laboratory on clayey ores to evaluate a clay-stabilizing polymer&apos;s effectiveness in preventing these problems. Test results indicate that treating the ores with the stabilizer could maintain permeabilities two to five times greater than the long-term permeabilities present in untreated ores. Both alkaline (pH 8.5) and acidic (pH 2.0) leaches were used in the permeability-leaching tests. Since in situ leaching throughput rate is directly related to permeability, these results also indicate a potentially beneficial effect on operating parameters such as capacity and injection pressure. To determine the reasons for the success of the clay stabilizers, an investigation was conducted to cieter-mine the effect of the stabilizer on clay swelling and dispersion. Clay-swelling tests indicated that the clay stabilizer reduced clay swelling. Zeta potential measurements made on fine clay particles treated with the stabilizer were compared to measurements made on untreated particles and indicated that the stabilizer was electropositive and, therefore, could reduce the degree of negative charge on the particles and their tendency to disperse or migrate.

Jan 1, 1984

By G. B. Goodman, W. H. Pailes, P. D. Kaplan, I. Stachura, V. Castronova

"The risk of developing silicosis in underground coal miners, tunnel workers and some foundry workers is well-known. These persons generally develop the classic form of the disease over a prolonged period of time. Workers involved in abrasive blasting of bridges and those polishing tombstones have been reported to develop an acute form of silicosis within a few years of commencing exposure. Not well-appreciated is the potential for development of acute silicosis among drillers at surface coal mines. We report the case of a 33-year--old man who worked primarily at surf ace drilling, developed acute silicosis within three years of beginning exposure, and who initially responded dramatically to corticosteroid therapy. CASE REPORTThe patient is a 33-year-old white man who worked as a rock driller at a quarry and also at surface coal mines in western Pennsylvania since 1975. Prior to 1983, much of his work was done with a wet process in which water was applied to reduce dust generation. After 1983 he worked primarily as a driller at a surface coal mine using a dry process. He never wore a respirator. He described the dust as being so dense that he ""couldn't see anything.- In August 1986, he presented to his local physician with a complaint of pleuritic chest pain and shortness of breath. A chest x-ray film was obtained showing only a few p and q opacities. He continued working and these symptoms subsided, but the patient noted the onset of progressive weight loss. By May 1987, he had lost approximately 50 lb. In addition, he suffered profound malaise, dyspnea, migratory chest pain and arthralgia, fevers and drenching night sweats.A course of erythromycin therapy given in the hospital resulted in only fleeting improvement. Studies for Legionella and Mycoplasma infections were negative, as was a tuberculin skin test. The patient was transferred to Allegheny General Hospital in Pittsburgh on June 4, 1987.There was no history of serious medical illness, including tuber¬culosis. The patient admitted to smoking between I and 1 1/2 packages of cigarettes daily for 2 1/2 years prior to May 1987 when he stopped smoking. He denied intravenous drug abuse, homosexual activity or receiving transfusions of blood or blood products.On physical examination the patient was a thin, febrile white man who appeared chronically ill. Bilateral axillary and cervical lymphadenopathy was present. Chest examination showed restricted expansion and bilateral crackles. Examination of the heart and abdomen disclosed no abnormalities."

Mar 1, 1992

By G. Deissman, S. Kistinger

For the last 15 years environmental Life-Cycle Assessments (LCA) have increasingly been used to evaluate the environmental performance of industrial processes and products and have been employed as a basis in decision making processes in the public and industrial sector. However, assessment methodologies for environmental protection measures and reclamation/remediation measures with respect to their consumption of natural resources are generally poorly developed. In this presentation a methodology for LCA of environmental protection measures and remedial actions, respectively is suggested, using the remediation/reclamation of mining sites as an example. Key aspect of this approach is the development of an evaluation method appropriate for environmental protection measures, which links the various impact indicators recognised in the impact assessments and allows their integrated assessment.

Jan 1, 2005

By Arkady Senchenko, Yevgeny Zhagun, Yury Kulikov, John Starkey

"The paper contains description of a new project in Russia - gold-processing plant at Aleksandrovskoye deposit (start up in September, 2013). The paper includes a brief description of plant flowsheet, data for material composition and technological properties of ore, as well as information about the achieved parameters of ore processing over the first months of plant operation. The project is interesting because a new semiautogenous mill and a ball mill were purchased on the basis of SAGDesign Consulting Group recommendations after the testing of ore samples characterizing the deposit according to specific years of operation. The plant has relatively small design capacity - 750 000 tpa, but nevertheless is the biggest gold-processing plant in the territory of Zabaikalsky region. Major valuable component in the ore is gold, silver is recovered as a by-product. The ores are very hard to grind. The design grinding flowsheet includes a semiautogenous mill operating in closed circuit with a screen, and a ball mill operating in a closed circuit with hydrocyclones (SAB). Process technology includes gravity processing and flotation with subsequent cyanide leaching of concentrates. Mill operation analysis and conclusions about the compliance of the achieved values to target ones are shown, as well as the accuracy of SAGDesign method when applied to very hard ores of Aleksandrovkoye deposit are presented in this paper. Basic directions of technological flowsheet optimization are also given."

Jan 1, 2014

By C. H. G. Bushell, G. Brown, C. J. Krauss

1N FLOTATION, copper sulphate is used universally for the activation of sphalerite and marmatite and, to some extent, for the activation of other minerals. The copper activated surface readily adsorbs standard collectors such as the xanthates and dialkyl dithiophosphates whereas untreated zir~ sulphide does not. With the host of reagents available, making a mineral float is seldom difficult. The problem is to achieve selective flotation. In zinc flotation, the great value of copper sulphate results from its ability to activate zinc sulphide preferentially to gangue minerals. At the Sullivan Concentrator of The Consolidated Mining and Smelting Company of Canada Limited, the most abundant gangue mineral in the lead-zinc ore is pyrrhotite, and the zinc mineral is marmatite of somewhat variable zinc to iron ratio. For this Cominco study, selectivity between marmatite and pyrrhotite was therefore the most interesting aspect of copper sulphate activation.

Jan 1, 1961

By David J. Hatem

Tunnels and underground projects are inherently more risky than vertical projects, which typically utilize more conventional design and construction approaches and are undertaken in the context of relatively ascertained and defined conditions. On tunnel and under-ground projects, there are a host of special risk factors, including unknowns and uncertainties as to the physical and behavioral characteristics of the ground, the inextricable interdependence and necessary interaction of design decisions and construction means and methods with those ground conditions as well as the manner in which risks are allocated among project participants for un-anticipated subsurface conditions. Public-private partnerships (PPP) projects, in their own respects (and independent of any major subsurface component), pose significant risk for all private sector participants. The main driver of owners to procure projects using PPP is financial, as often all, or substantially all, of the design and construction risk are transferred to the private sector consortium, including the design-build (D-B) team. For a concerning number of those public owners, that risk transfer regime includes rather onerous and aggressive contractual terms that allocate to the private sector participants substantially all risks associated with the encountering of unanticipated subsurface conditions. These aggressive risk allocation provisions, while directly impacting project participants upstream of the consulting engineer, have an indirect and corresponding risk intensifying effect upon consulting engineer professional liability exposure. There are many factors that result in increased professional liability exposure for consulting engineers involved in PPP projects. The more prominent and prevalent of those factors fall into the following categories:

By Armando Valenzuela

Arsenic has been a common impurity in copper sulfide concentrates treated pyrometallurgically in Chile, which inevitably during the smelting-converting process reports in the final copper product affecting its properties, but also affecting environment as a very toxic occupational hazard. The enforcement of air quality standards, which regulate pollutants such as sulfur dioxide, particulate matter, and arsenic, has resulted in the implementation of pollution abatement plans and emission reduction schedules mainly by state-owned copper concentrate smelters. Investments associated with these plans incorporated gas-handling systems in order to capture polluting emissions. Electrostatic precipitators recover dusts containing mainly Cu and As which are leached to recover copper, while arsenic is disposed currently in the form of ferric arsenate. Gases containing high sulfur dioxide content are treated in plants to produce sulfuric acid, which is used in various classical and new hydrometallurgical processes. Additionally, smelters have effluents treatment plants for arsenic disposal either as ferric arsenate or calcium arsenate/arsenite. This paper reviews the environmental situation of the Chilean metallurgical industry, and the present trends for arsenic management are particularly emphasized since Chile is the world?s largest copper producer.

Jan 1, 2006

The coal-based power generation industry faces increased pressure from all sectors to improve its environmental performance. This is due to increased awareness of and concerns regarding greenhouse-and acid-gas emissions, toxic metal releases (to both air and water) and water availability. A methodology to assess this industry?s environmental performance is needed. Such a methodology should assess all environmental impacts accurately, recognizing the irspatial and temporal dependence, and taking into account the social acceptability of technologies employed. Here, we develop a methodology to determine the environ-mental impact associated with solid wastes generated by this industry, and apply this to the specific case of ash management. More specifically, the case study compares the environmental footprint of an ash deposit for a number of operational water management scenarios. The methodology considers leachate generation processes from ash impoundments to obtain a time-dependent concentration profile of mobile constituents at the interface between the ash impoundment and the surrounding environment. This leachate prediction modelling is subsequently linked to plume dispersion modelling tools to determine the fate and transport of leached components, predominantly salts, into groundwater. Together, these provide a measure of the extent to which a land mass is affected by leachate migration from the deposit. To determine the exact boundary between regions of acceptable and unacceptable risk to the environment, we use Ecological Risk Assessment concepts. In this way it is possible to obtain a time dependent affected land footprint which could be used as an indicator of the environmental impact of solid waste management practices. This information can be included in a set of environmental criteria which form the basis of an overall environ-mental impact assessment, using tools such as Life Cycle Assessment (LCA). The value of LCA is that its structure is consistent with accepted models of environmental decision making, where different approaches to valuation in impact assessment assist in prioritizing impacts on the basis of their perceived significance. The proposed ?affected land footprint? metric represents a significant improvement over current LCA impact indicators for solid waste management practices. Keywords: Environmental Impact Assessment, Environmental Risk Assessment; Life Cycle Assessment; coal ash; leachability; salinity

Jan 1, 2002

By M. Z. Sukiennik

A static method for vapor pressure measurement up to 1450 K and above 1 hPa is presented. The method is designed for equilibrium and kinetic studies of metallic systems, including those with a chemical reaction. Application examples are given for determination of activities in condensed phases, and heterogeneous reaction rates and equilibrium constants.

Jan 1, 1993

By Konstantina Chalastara

Mixed phase titanium dioxide (TiO2) nanoparticles synthesized through hydrolysis of TiCl4 solution at different conditions, namely concentration, pH, and residence time are characterized and evaluated as photocatalysts. The process is operated in a continuous stirred-tank reactor, CSTR giving blends of anatase, brookite, and rutile nanoparticles that were further evaluated to find the optimum mixture for a photocatalytic sorption material. The titania nanoparticles are first characterized in terms of photocatalytic activity under UV light illumination using an organic model compound (methyl orange) and after that are tested for removal of toxic selenate and selenite species from simulated effluent waters.