Search Documents

In the course of work being carried out in the Lubricants and Bearings Section of the Council lor Scientific and Industrial Research on the production of copper4ead 'bearings for 'use in aircraft, it has been found necessary to develop special metallographic methods. For proper control of the production of steel-backed copper-lead bearings it is necessary to adhere to rigidly controlled conditions, and it is essential that a method of examination be adopted which will readily detect actual defects or any variations in quality. Some defects can be observed with the naked eye, whilst others are detected by radiographic examination. This latter method is invaluable as a rapid, reliable test in the production of aircraft bearings, but it is necessary to observe the structure of the alloys under the microscope, both to be able to interpret the radiograph correctly and to determine what has occurred to the metal during and after solidification. The use of a sound metallographic technique is'particularly important in developmental work and research connected with these bearings.Polishing TechniqueCopper and lead are practically immiscible in the solid state, but whilst they are miscible only in certain limited proportions in the liquid state; consequently "alloys" of copper and lead consist of a mixture of the constituent metals. The metallographic difficulties are obvious. Copper is a relatively tough metal, although it readily scratches, whilst lead is extremely soft and easily deformed. It wouId be expected if any normal polishing technique were applied that the lead would be readily torn out of the surface being prepared, and, in addition, that the lead would tarnish very easily.Grange(2) has described a method by which these difficulties can be overcome. The method involves an etch-polish procedure using "chrome regia" as an etchant for the copper. The chrome regia was a solution of chromium trioxide and hydrochloric acid in water. This type of etchant has been adopted, but it was found necessary to make certain changes.The method now adopted in this laboratory is as follows: The specimen (which is usually mounted in bakelite) is wet ground in a series of successively finer Hydro-Durexsil emery papers down to 60.0· grit paper.The specimen is then etched in the chrome regis, etchant (the composition of this etchant will pe discussed later) for approximately five seconds.Most efficient etching is obtained by swabbing the surface of the specimen...

Jan 1, 1944

By J. W. Wilson, P. C. Graham

SUMMARY The Witwatersrand quartzites in which South African gold mining operations are moat exclusively conducted, are notoriously difficult and costly to drill. Despite this situation, however, with the high cost of developing new mines and extending existing mines, together with the rising cost of labour and mining problems resulting from the ever-increasing depths of workings, the demand for raise-boring in these formations is increasing rapidly. Not only is the demand for raises and shafts increasing, but also the length and size of these excavations. Raise-boring studies carried out in South African gold mines have indicated that increased penetration rates and possibly reduced costs could be obtained if higher thrusts were available at the reaming head. Until fairly recently there has been no raise-boring machine suitable for underground use that possessed the thrust and torque characteristics necessary to achieve high penetration rates in hard abrasive quartzite formations and the cutters available were not really developed for high loading. In response to these requirements a raise-borer, the Robbins 83R was designed and built in Seattle, U.S.A. for the Anglo American Corporation. This machine is operating in South African gold mines and is currently being used at a depth of 12 000 ft below surface in one of the. Group's mines. The initial raises bored have substantiated that increased penetration is attainable at high thrust and it is now apparent that the machine is sufficiently versatile to drill raises of up to 12 ft in diameter in quartzite formation over a length of 2 000 ft.

Jan 1, 1974

By Hooman Askari-Nasab, AHLAM MAREMI, EUGENE BEN-AWUAH

In oil sands mining, tailings are voluminous unwanted by-products generated from extracting the desired mineral from the mined ore. Dyke construction and backfilling activities require well-managed techniques to facilitate progressive reclamation at the earliest opportunity. This directly affects the sustainability and profitability of the mining operation. This research introduces a goal programming framework that simultaneously optimizes the (1) production schedule with limited duration stockpiling and directional mining; (2) dyke construction schedule; (3) size, shape, and location of tailings-cells; and (4) mining and processing production targets. The results show that in creating in-pit tailings-cells designs, decreasing the mining-cells volume and increasing the number of mining-cells improve the net present value of the operation due to increased operational flexibility. The model generated a uniform schedule for ore and practical tailings-cells designs for backfilling activities. Integrating tailingscells optimization into oil sands mine planning and waste management ensures the efficient use of in-pit mined-out areas required for sustainable operations.

Apr 14, 2021

By KOKOWSKI J., RUDZIŃSKI Ł.

The LUMINEOS network was established in 2013 to monitor mining-induced seismicity in Legnica-Głogów Copper District (LGCD), located in south-western Poland. Since the starting time, the network was improved and today consists of 17 seismometers and 10 accelerometers. Up to now, the strongest recorded earthquake in the region had Mw4.0. Both raw seismic data and earthquakes catalog for events recorded by the LUMINEOS network are fully open and available on the EPISODES platform (https://tcs.ah-epos.eu/#episode:LGCD). During the last 7 years, the network improvements gave us a possibility to increase location accuracy for shallow mining events. This accuracy is influenced by factors such as the configuration of seismic stations, noise level at seismic stations, and the influence of the velocity model. Here we encountered two main issues which are worth to discuss. The first one is the low detection threshold of two seismic stations and their significant impact on the location errors. The second one is the large uncertainty in the S-wave picking. Even though S-waves are not so clearly visible on seismograms, they are very helpful in the estimation of source location and strength of seismic events in the region. In our work, we present the history of LUMINEOS network and corresponding improvement on location accuracy as well as the influence of noisy stations on the error distribution and how it is connected with location results. We also investigate the effect of the S-wave phases and how they are related to the accuracy of the earthquakes locations in the network.

Apr 26, 2022

By Ralph W. Crosser

The emergence of residuals management as a planning and management tool in the mineral industry has been recently accelerated by the proliferation of environmental regulation and its associated costs. Residuals management practices allow for the early determination and integration of both production and environmental goals in the development of management strategies to arrive at the most cost effective, environ- mentally sound solution. The term residuals management was in actuality derived from the substitution of the word residual for the term ?pollutant? or ?waste?. A residual can be defined as a non-product output having no value in existing markets or a value less than the cost of marketing it. The values of the residual can be determined by time, technology, government policy, market conditions, etc. Residuals basically fit into two classes -- materials which are composed of liquid, gaseous or solids; and, energy, which mainly consists of heat and noise. These residuals are interrelated and can be modified by adding materials and/ or energy, which also may become a residual; thus, lending themselves to alternate disposal schemes to control the adverse effects.

Jan 1, 1979

By C. E. Meissner

THE need for a practical method of deciding upon new alloy steel analyses to widen its markets was the problem facing the Chrome Steel Works at the beginning of 1927. In addition to determining the physical properties of the alloys under consideration, it was necessary to test their value in service. Small melts of steel in a crucible, from which test specimens could be made, were insufficient to determine more than physical properties, therefore actual castings and ingots had to be made before the products could be placed in service. Furthermore, to save further experimental work, it was desirable that these heats should be made on a "pilot" basis; that is, actually duplicating regular open-hearth furnace practice. Therefore a one-ton (2000-lb.) acid open-hearth furnace was built. FURNACE DESIGN There are no special features in the design of this furnace. Standard acid open-hearth practice is followed, with the reproportioning of the dimensions necessitated by its small size; notably, a considerably increased length in proportion to width in order to get proper flame propagation. After the first heat was made it was found that the checkers were insufficient. The checker chambers were increased in size and the checker openings were made much smaller. The furnace was started late in March, 1927, and made 65 heats. Experimental work was then stopped until the data accumulated could be worked up and summarized. The run was resumed in November and the furnace is still operating, having made at this writing 60 additional heats. For the last series of runs, there was some rebuilding of both the furnace itself and the checkers. Slag pockets were added. Fig. 1 shows details of construction; Fig. 2, the, general appearance. All designing was done by the operating and engineering staff. Construction materials were those available around the plant. The reversing valve is a standard butterfly type taken from an old furnace.

Jan 1, 1928

By LeRoy A. Thorssen

The use of lightweight aggregate as a constituent of concrete is not a recent development. Pumice was used by the early Romans, in pozzolana cement concretes, in the construction of many of their works. However, the recent development of manufactured lightweight aggregates, such as the expanded shales, vermiculite and perlite, has created a possible use for a whole new group of Portland cement concretes. Concrete can now be produced with unit weights ranging from 30 to 150 pounds per cubic foot and with various insulating, fireproofing, acoustical and structural properties. The tonnage of such materials being used has increased considerably in each of the past ten years, and can be expected to increase for the next several years as availability of the aggregates becomes more widespread and the properties of such concretes become more thoroughly investigated and more generally known. LIGHTWEIGHT aggregates of many types have become avail-able to the construction industry in most localities on this continent

Jan 1, 1963

By Fernando Romero Lage

"Crushing and screening theory and application has remained fairly consistent in the last 50 years. The application of such equipment is guided by varied formulaic conventions and rules that due to the entropic nature of the process, remains more an art than a science. The variability of conditions creates an environment in which trial and error becomes the principal means of process balance and control. This paper illustrates some of the theories behind the process, plus other assumptions, postulates, myths and misconceptions that exist within the crushing and screening industry.INTRODUCTIONContinuous material balance calculations are habitually performed in the design of new comminution circuits as well as in the valuation of existing circuits. A continuous material balance calculation is one in which the input rate of material is equal to the output rate for each unit functioning in the circuit. At continuous analysis, there is no accumulation or losses of material within the system, as it is when performing a discrete event analysis.In order to produce viable and manageable mine-to-mill material, whether it is ready to leach or ready to mill, we must reduce the material in a series of stages. The power demand increases as the material size decreases, as it is when folding a piece of paper successively. As with the paper, there is a crushing size limitation that is a consequence of the mineral properties such as work index, moisture, viscoelasticity, etc. Comprehensive knowledge of crushing plants in both the aggregate and the mining industries show that, after three stages of crushing, a particle size distribution originating from a blasted deposit can be reduced from an nominal maximum size of 500 mm to a nominal maximum size of 12 mm. if the last stage of crushing is set in closed circuit, the screen openings will be able to yield a smaller top size.Achieving steady and continuous material balance poses major difficulties as crusher lose their settings, screens blind or peg, and material characteristics change geographically or seasonally. Overloading conditions in crushers and screens are nothing but counterproductive, and the net losses of an unbalanced circuit can be overlooked when mining operators are paying a lot more attention to the evermore complex systems downstream.It is not simply the crushing of the mineral but achieving the right size for the downstream milling process that will yield the maximum amount of energy savings."

Jan 1, 2010

By J. Chlan

"Dryer DescriptionProctor and Schwartz Continuous Conveyor DryerThe Proctor and Schwartz Continuous Conveyor Dryer has been in operation since July 1958, and comprises six unit• - an 8• wide single conveyor with roller extruder, insulated housing, type 304 stainless steel circulating and exhaust fall system, steam heating coils, temperature controls and discharge crusher rolls. Entire dryer dimensions are 52’ x 12'0""weighing 53,000 lbs,Extruder rolls - setting is 1/8"" (Drive 3 HP 1800 RPM) clearance off the extruder screen.Conveyor - consists of 151 interlocking pans, measuring 8"" x 8' (2 HP 1200 RPM) One Exhaust Fan (5HP - 900 RPM)Steam Coils -- l"" steel pipe - with steel fins -- each coil measures 16' 2’’- 64 coils in the No, 1 Compartment- 64 coils in the No, 2 CompartmentDryer OperationThe yellowcake slurry at 28% solids is pumped to an 81 x 8' Peterson Filter. The filter media presently being used is a Neotex 4372 blanket, being 100% staple fibre nylon, 12 oz per square yard with air porosity of 9 CFM's. The cake discharge at 45 - 50% moisture falls into the roller extruder. Extrusions are formed by forcing the material by rolls through a perforated plate moving back and forth and depositing the spaghetti-like extrusion on onto the dryer-conveyor.The conveyor now carries the extruded material through the heating chamber•, The feed end of the dryer will be referred to as No. 1 Compartment, with temperature control set at 280""F. The circulating fans take the hot air off the coils and circulate the heated air through the perforated openings in the dryer conveyor pane, After passing through the set of steam coils and circulating fan in No, 1 Compartment, the material then goes through No, 2 Compartment where the temperature is set at 305'F, Final material then discharges through a set of crusher rolls set at ~"". Moisture of final dried product runs at less than 2%.The dryer conveyor load is usually run to a 3"" - 4"" depth load. Conveyor speed at approximately 90 minutes for load to pass through. Load onto the conveyor is controlled by boot level and speed of the 8' x 8' filter. The dryer steam coils are water-washed twice a month."

Jan 1, 1972

By W. E. Bearce

The recent concern for the recovery of even the finest fractions of coal preparation plant feeds has created needs for new equipment. Thermal dryers currently available have difficulty reducing the filter cake moisture on down to the desired point. This difficulty involves 1) the physical problem of handling this wet, sticky material and making each particle accessible to the hot gases, and 2) removing the extremely fine dried particles from the cooled gases. The dryer described in this paper handles the first of these problems, and eliminates the second by the substitution of steel balls for air as the heat transfer medium. As a general statement, the cost of preparing coal for market is inversely proportional to the size of the lumps or particles. In the not too distant past the finer sizes were discarded as being uneconomical to treat and this practice might be still continuing if it were not for the insistence of the public that this material be kept out of our streams. This being the only cost-free outlet, the disposal of fine refuse became a significant item of expense in every preparation plant. When this happened it was only reasonable to look to the recovery of the values in this material, not only to defray this expense, but to reduce the tonnage which had to be wasted. There seemed to be no device available suited to reducing the moisture in this material to what the market requires. All of the fine coal dryers commonly employed make use of air to bring the heat of combustion into contact with the coal particles. Any device employing air as a heat transfer medium, has the following two strikes against it in attempting to handle 28 mesh by 0 filter cake: 1) It is practically impossible to bring the hot air into intimate contact with the enormous number of fine particles stuck together in the cake. 2) Even if this can be effected, it is impossible to remove the dried coal from the air. A wet scrubber must be employed, the discharge of which must go back to the filter and dryer as a circulating load of the most objectionable sort, being the extreme fines. Various compromises have been used to cope with the problem of drying this relatively small tonnage of high moisture coal. Often some of the dried coal is mixed back with the feed to the dryer in an attempt to make the mixture more handleable and more available to contact with the hot air than the filter cake alone would be. This may help to some extent with the first problem but it does nothing about the second and a dryer operated in this way has to be oversized. Sometimes the filter cake is mixed with a coarser fraction for the same reason. Here again, while this may make a mixture (the particles of which are more readily brought into contact with the hot air), the problem of getting the fine coal out of the air remains and a larger percentage of the total coal to be dried is handled by the most expensive means. Mechanical dewatering has accounted for more and more of total coal drying lately and in many cases would satisfactorily handle the whole load, down to 28 mesh, if there were a means available for doing a good job on the —28 mesh by itself. The dryer which is the subject of this paper was designed expressly for doing this job — drying fine material by itself regardless of how wet it may be to start with, how fine it may be, or how gummy and sticky these properties in combination may make it. The essential features are depicted in Fig. 1. A rotating cylinder is supported on a frame in such a way that one end may be raised or lowered by hy-

Jan 1, 1968

By D. T. Couillard

Video technology is becoming an important tool for many designers of industrial training programs. This report describes how trainers at the Minntac Mine, Mt. Iron, MN, have developed videocassettes of safe job procedures (SJP's) for training miners assigned to perform unfamiliar work tasks. All steps necessary for videocassette production, from idea to finished product, as well as the required equipment and prices, are listed and/or briefly explained. Minntac officials believe that the SJP videocassettes have contributed significantly to a reduction in mine accidents.

Jan 1, 1985

By Ramsey Hart

MiningWatch Canada is the only national independent civil society organization with an exclusive focus on mining in Canada and Canadian mining companies operations internationally. In 2005, MiningWatch Canada collaborated with other NGOs to develop the Framework for Responsible Mining: A Guide to Evolving Standards. The project was the result of a perceived need by NGOs and retailers, particularly from the jewellery sector, for a framework that would set out environmental, social, and governance standards for the minerals sector ?providing recommendations for retailers and others seeking to source or invest responsibly, as well as regulate and encourage responsible mining practices?. This paper is a reflection on the Framework that examines key areas of concern and notes where the industry norms and expectations of civil society have evolved. The paper focuses on developments in social issues related to the UN Guiding Principles on Business and Human Rights, new initiatives associated with financial transparency, the UN Declaration on the Rights of Indigenous Peoples. The environmental components of the Framework that are revisited are waste management, biodiversity, energy and climate change, environmental assessment, mine closure, mercury and seabed mining.

Aug 1, 2013

By G. D. Buson

Driefontein Consolidated Limited has a proud history in the South African gold mining industry dating back to March 1945 with the formation of the West Driefontein Gold Mining Company. The reclamation gold plant at West Driefontein was originally built as a uranium recovery plant in 1970. With the collapse of the uranium oxide yellow cake market, the uranium plant was closed in 1988and successfully converted into a gold plant, recovering gold from repulped tailings dams1. The West Driefontein Reclaim plant utilized milling, leaching, conventional rotary vacuum filtration and cementation to recover the gold at a rate of 200,000 dry tons per month. The No. 1 tailings dam (at a head grade of 0.8 Au g/t) began to near the end of its life during 1996, and the next slimes dams to be treated, the No. 2tailings dam (at a lower head grade of 0.56 Au g/t) was found too marginal for reprocessing using the filtration technology. Alternate technologies were investigated, particularly the carbon-in-pulp (CIP) plant based on the Anglo-American Corporation (AAC) pump-cell technology at the Vaal Reefs Exploration and Mining Company?s East gold plant which was operating profitably at lower head grades2. The AAC pump-cell technology is based on the carousel mode of operation2. The suitability of CIP technology for the West Driefontein Reclaim plant was investigated using a pilot plant pump-cell supplied by Kemix The data gathered were utilized in sizing a full scale AAC pump-cell plant. This plant was motivated, built and commissioned on the 22nd of November 1996. Incorporating 6 eighty cubic metre AAC pump-cells. The West Driefontein Reclaim plant initially treated repulped slimes dam material. A subsequent change of feed material to current arisings (from the main gold plant) occurred in1997 in order to convert mills for waste rock treatment. Currently the reclaim plant treats a combination of current arisings and waste rock (milled at the reclaim site). The new CIP plant replaced twenty-seven rotary vacuum filters. A comparison between the filters and CIP in terms of operating costs was undertaken, as well as a performance analysis of the CIP plant to determine its flexibility in terms of variation of the throughput, pulp density, gold input, leaching efficiency prior to CIP, and the rate of carbon movement.

Jan 1, 1999

By N. Damiano, C. Zhou, R. Jacksha, J. Srednicki

Modern electronic devices and systems used to enhance miner safety and health are becoming commonplace in underground coal mines. The ability for these devices and systems to function properly in the presence of electromagnetic emissions from other electronic and electrical devices and systems is not entirely understood. To investigate potential electromagnetic compatibility issues of critical mine electronic devices and systems, researchers from the National Institute for Occupational Safety and Health (NIOSH) are conducting surveys of electromagnetic emissions in underground coal mines. This paper presents the measurement system, methods, and results of electric field electromagnetic emission surveys conducted in three underground coal mine environments in the frequency range of 10 kHz to 1000 MHz. The survey data show that in some environments electric field electromagnetic emissions in underground coal mines approached or slightly exceeded limits as defined by other industrial sectors.

Mar 2, 2022

By George L. Gates

[When clays are mixed with water to -.,tee mud fluids for use in trilling wells for nil and --ac b ;l-,e rotary method the liquid mixtures have certain physical characteristics that vary with the quantity and size of their inherent solid particles. All naturally occurring clays contain variable quantities of particles of different sizes ranging from relatively coarse (sands) through -,.tedium (silt) to fine materials of colloidal dimensions. Tie colloid content is extremely important 2.s a desirable _.'ale constituent of mud fl-z to fit well drilling. ';'it:-out colloids the souk?;,' in a mud fluid wouldr rapidly, end ti-c-and. wall-building qualitites of the' fl,-,id would l ..o r re 1 impaired. Mud .fluid.^ with insufficient quantities of colloids also are lacking in "lubricating" g listen, and it is, to ° min casing in, -)re holes drilled with such fluids.]

Jan 1, 1941

The Lornex mine is located in the Highland Valley area of British Columbia, Canada, one of the most,promising districts of low-grade porphyry-type copper mineralization in the world; Lornex is operated by Rio Algom Mines, Limited, a member of the Rio Tinto Zinc Group of London. Exploration from 1965 to 1968 disclosed an ore body of 293 million tons with a grade of 0.43% copper and 0. 14% molybdenum; this led to the decision to construct a 38,000 tpd operation, and production commenced in the fall of 1972. The ore is open-pit mined with 15 cu yd (11 5 m3 shovels, which load 100- and 200 -ton trucks. These trucks dump directly into a 60 in. by 89 in. Allis -Chalmers gyratory from two sides of the 14 ft 6 in. (4.42 m) deep dump pocket and across splitters mounted on the pocket sides. The unlined pocket would hold 1,000 tons level full. The crushedore discharges into a 300-ton surge hopper equipped with an automatic sonic level indicator to prevent over -filling. A 96 in. by 23 ft (2.44 m by 7 m) apron feeder delivers the ore from the surge hopper to a 72 in. (1.83 m) transfer belt equipped with a tramp iron metal detector. The transfer belt discharges to a 60 in. (1. 52 m) conveyor which conveys the ore about 3,000 ft (914 m) to the 475,000 ton ore storage pile located near the concentrator. Four 48 in. (1.22 m) pan feeders transfer the ore to the mill feed conveyors, which in turn supply the two 32 ft by 15 ft (9. 75 m by 4. 57 m) semi-autogenous mills, which easily accept the 10 in. (254 mm) product of the crusher. Each semi- autogenous mill is followed by a secondary ball mill. The unusually large open side setting of the crusher accounts for its 6,300 tph maximum capacity. Concentrator capacity is now 48,000 tpd. Eccentric removal is eased by the design of the door to the crushed ore pocket, which has the cart rails mounted on its outer surface and is lowered to a horizontal position in the pocket by an electric winch. The top of the door rests on wear bar covered concrete piers in the pocket. Another feature is a chute through the floor at the crusher base that extends into the crushed ore pocket. Dust and spills of ore on that floor during crusher repairs are easily swept into the crushed ore pocket. This feature is also used at Bougainville and Palabora and has been added to others after operation has commenced. The design follows the concrete rectangular box concept with four main service and maintenance levels shown in the sectional drawings, although a third additional section has been added at the maintenance

Jan 1, 1978

By S. Upadhyay, A. M. Afrapoli

"Fluctuation in market price of mineral products has enforced mining companies to cut down their operating costs. One useful way of reducing operating costs in mining operations is to make optimal operational decisions, incorporating efficient mining fleet management systems (FMS). Over the last 50 years, several types of FMS have been developed and introduced in the mining systems around the world. However, there are two major shortcomings in existing systems. Firstly, none of the existing systems consider effects of the short-term plan on dynamic truck assignment. Secondly, most of the existing FMSs make decisions in a way that optimize a specific objective while ignoring others. Herein, we propose a multi stage and multi objective FMS that deals with aforementioned shortcomings of the currently available systems. The developed FMS, in its upper stage, links semi-dynamic operational decision making process to the short-term production plan by simultaneously assigning shovels to mining faces and allocating trucks to the shovels by implementing its first multi objective decision making model. Then in its second stage, in a real time dynamic decision making process, it assigns trucks to shovels and corresponding destinations by optimizing its second multi objective decision making model. The developed fleet management system has been verified using an Iron ore case study and the results are presented in this paper. INTRODUCTION Open pit mining method is the most common method to mine mineral from the earth. Based on Wetherelt and van der Wielen (2011) there exist 2500 open pit metal mines that are categorized as industrial scale mines. Over all of those, the amount of material handled using truck and shovel material handling system is more than the amount handled by all other systems together (Humphrey & Wagner, 2011).It has been proven by several studies that more than 50 percent of operating cost in a truck and shovel based open pit mining operation is accounted for material handling (Moradi Afrapoli & Askari-Nasab, 2017, Alarie & Gamache, 2002, Ahangaran et al., 2012). Thus, introducing even 1 to 2 percent cut in its material handling cost saves huge amount of money for the stakeholders. Over the last 50 years, two major areas have been identified to cut this cost. On one hand mining industries have been implementing equipment with higher production capacities, and on the other hand, researchers have been developing operations research techniques to make dynamic decisions as close to optimal as possible to deduct operational costs in truck and shovel based mining operations."

Jan 1, 2018

By R. L. Kidd, T. H. Miller

"INTRODUCTION This paper is the seventh of a series of yearly reviews started in 1921 and pre¬sents information gathered in a cooperative investigation undertaken by the United States Bureau of Mines and the University of Utah. It is the purpose of this report to make available flotation—reagent consumption data and other milling information in such a manner as to be of value to the milling industry and to the manufacturer of flotation reagents.These data have been compiled from a survey of about 300 concentration plants in the United States. Much additional information has been obtained from the various offices of the United States Bureau of Mines. Many of the plants covered in the survey made complete reports of their operations, but others were apparently unable to supply this information in sufficient detail to meet the requirements of this report. As a result, some sections of the report are more complete than others. In general, however, the mill reports were much more complete than in previous years, and for the first time it has been possible to calculate average mill recoveries in the treatment of certain classes of ores. As in the past, every effort has been made to conceal individual plant operations.ACKNOWLEDGMENTSIt is realized that the publication of this information is possible only through the assistance of the mill operators, and the authors wish to express their appreciation of this cooperation. Thanks are also due the various field offices of the United States Bureau of Mines, division of mineral statistics, for assistance in collecting this information."

Aug 1, 1931

By AIME AIME

In the present number of Mining and Metallurgy, issued on the fiftieth anniversary of the founding of the Institute, it appears appropriate to chronicle a few of the interesting incidents respecting its early life. We are fortunate in being able to cull the following notes from unpublished manuscripts of Doctor Raymond and Doctor Drinker, than whom no other members could have written with greater exactness and fidelity. THE seventh decade of the 19th century may be said to have marked an. era in the history of the world. Industrially and .commercially it was marked by the wide application and utilization of discoveries already made, which came to their full effect at this period in steamships, railways, telegraph and cable lines; the standardization of parts in machines, from watches to locomotives; the use of 'dynamite, antiseptic surgery, the open-hearth steel process, the compressed-air rock-drill, the electric generator, and the Gatling gun. Through the opening of the Suez canal in 1870 the maritime trade of the world was revolutionized, sailing vessels were supplanted by steamers, while ocean cables and ocean "tramps" brought about far more rapid movement of commerce than had before been experienced. Politically, this period was marked by the sudden birth of the German empire and the beginning of that intensive internal development of the national resources of that empire in preparation for colonial extension and war, the amazing result of which has been made evident by the recent world conflict. In the United States, the significance of this decade was peculiarly important. The re-admission to the union of Virginia, Mississippi, Texas and Georgia in

Jan 1, 1921

By E. V. Koporulina, I. Zh. Bunin, M. V. Ryazantseva

"We studied the mechanism of structural and chemical transformations of columbite, tantalite, zircon and feldspar surface during the treatment by high – power electromagnetic pulses (HPEMP) using the methods of X - ray photoelectron spectroscopy (XPS), analytical electron microscopy (SEM - EDX), Kelvin probe force microscopy and flotation experiments. According to XPS and SEM - EDX data, major changes in the atoms chemical state of investigated minerals surface are related with formation and modification of functional cover and changing in concentration (% at.) of hydroxyl groups on the mineral surface, leading to increase in the contrast of technological properties of the rare metals minerals. Research has identified the optimal parameters of HPEMP - treatment of rare - earth minerals Npuls ??104, Ttreatment ??100 sec. improving the selectivity of the flotation separation of columbite and zircon. The difference in mineral recovery into the froth (? e) before and after HPEMP - treatment was about 11 % and 24.5 %, respectively. No significant increase was observed in the flotation activity of feldspar. This study's findings demonstrate the effectiveness of HPEMP - treatment in inducing a controlled change in the structural and chemical properties of rare - earth minerals and improving the process efficiency for the processing of rougher tantalum - niobium gravity concentrates.INTRODUCTIONThe importance of improving the processing methods of tantalum-niobium ores and concentrates is explained by the mineralogical properties of rare - earth ores. These are properties such as the variable mineral, chemical, and grain size composition, complex morphometric properties, and the dissemination of ore mineral grains of micro - and nanometric size. Iron oxide and hydroxide films on the mineral surfaces neutralize the surface physicochemical and absorption properties of the minerals. Both in Russia and globally, nonconventional (non - mechanical) methods are being developed based on physicochemical, electrochemical, and pulsed energy impacts to improve the efficiency of disintegration and liberation processes of disseminated mineral complexes and to enhance the contrast of the structural, chemical, and technological (floatability) properties of refractory ores. This study is devoted to the investigation of the applicability of high – power electromagnetic pulses (HPEMP – treatment) for the change in the structural and chemical properties of rare - earth minerals and improving of the flotation properties contrast."

Jan 1, 2018