Search Documents

By K Smith

This paper presents an assessment of the Robertson (2010a) method within the CPTu inversion parameter framework of Been et al. (1987), using CPTu calibration chamber data presented by Jefferies and Been (2015) and in other literature to assess the validity of the method, with particular focus on applicability of the method to TSFs (i.e. its applicability to loose silts and silty sands). The assessment demonstrates that although the method estimates values of k consistent with calibration chamber data, the method estimates values of m that are generally 1.5 to 2 times greater than calibration chamber data. As a result of this, the method generally overestimates Ψ for values of Ψ less than 0, and underestimates Ψ for values of Ψ greater than 0. This may result in both overly conservative assessment of materials as potentially liquefiable and unconservative predictions of material behaviour for loose materials.

Jul 1, 2021

By A. J. Friedrich

Conveyor belts are designed to go unnoticed. When they work well, they attract little attention. When they are not doing the job right, it is noticeable, and they need to be fixed immediately. Vulcanising contractors compete for the maintenance of belts in mining/quarrying and general materials handling worldwide. Damage repair is approached in similar fashion. The damaged section of belting is normally cut out and discarded, and the belt re-spliced using hot vulcanising, Cold splicing, or mechanical fasteners/clip joints. However, there is a cost-effective alternative, alleviating the need to remove damaged sections which are often perfectly recoverable. This is the use of cold-curing repair resins and adhesives.

Jan 1, 2000

By J. Jacob, A. G. Guézennec, F. Savreux, S. Nanaa, M. Delclaud, P. d’Hugues

Mining wastes can contain base and precious metals, but also metalloids and rare earth elements that are nowadays considered as highly critical for the industrial development of the European Union. The development of alternative routes to conventional processing is still required in order to decrease the cost associated with the treatment of these resources, which are more complex in composition and with lower grades. An ecologically acceptable and yet economic alternative for processing of low-grade sulphidic primary ores as well as mining wastes is the extraction of metals using bioleaching processes. The purpose of this study was to test the potential of bioleaching procedures for the extraction of residual metals contained in sulphide-rich tailing wastes coming from a European copper mine. These wastes are mainly composed of pyrite (60%) and contain cobalt (0.06 %) and gold (0.95 g/t). Bioleaching experiments were performed in 2 L stirred reactors in batch mode and in pilot tanks (110L) in continuous mode, using the "BRGM-KCC" bacterial consortia. High metal extractions were obtained (cobalt dissolution > 90%), which confirm that bioleaching is an effective process for this tailings material. Experimental results were used to design a global treatment process scheme and to perform a preliminary economic evaluation, showing good profitability of a hypothetical industrial project.

Jan 1, 2014

By H. S. Chiang, S. S. Peng

"SummaryAir velocity distribution surveys on four mechanized longwall faces are presented and discussed. Although there are discernible patterns in the velocity distribution, there are wide differences in distribution in the cases examined. This can be attributed to differences in mining and face geometry. An important factor is air leakage into the goaf.IntroductionOver the past two years several intensive air velocity surveys have been carried out in West Virginia coal mines as part of a programme aimed at understanding dust transport mechanisms on mechanized longwall faces. These are presented here and some of the patterns of velocity distribution are discussed.Ventilation survey methodologyThe air velocity vector consists of three mutually perpendicular subvectors; the vertical subvector is directed toward the roof, one of the horizontal subvectors is parallel to the coal face and the other pointing to the gob. The air velocity which was measured in this paper is the horizontal subvector parallel to the coal face.To record the velocity distributions at the longwall faces, the surveying stations and the surveying points were established as follows.(1) The first station usually was set at the third support from the headentry T-junction. Within the first few supports, the air coming from the intake airway encounters a sharp right-angle turn at the T-junction, and forms a turbulent region close to the coal face. The intake air in this region is also influenced by the motors that drive the face conveyer. But when the air reaches the different. But for the same face the number was the same. The main air-travelling area was divided into six to 12 equally sized sub-areas, and each surveying point was situated approximately at the centre of the sub-area.The velocity survey was carried out by two persons, one reading the meter and the other taking down the readings. A complete survey at one station took about 5-8 min. Usually, the dimension of the cross-sectional area was measured during that time.A third person used the smoke tubes to observe the following: (I) the air movement patterns at different locations; (2) the extent and the direction of the air leakage; and (3) the machines' influence on the main airflow. At the same time he observed and recorded the roof conditions and the compactness of the roof-caving in the gob."

Mar 1, 1989

By J Foster

The Lanfranchi Nickel mine is located approximately 48 km south of Kambalda in Western Australia. Mining first commenced in the mid-1970s under the previous owner, Western Mining Corporation Ltd. After two years on care and maintenance, Panoramic Resources (previously known as Sally Malay Mining Ltd) purchased the operation in November 2004. The site currently produces approximately 10?000 tonnes of nickel metal annually from approximately 430?000 tonnes of ore. The Ore is mined from four main orebodies; Deacon, Helmut South, Lanfranchi and Schmitz. The Helmut South orebody is situated approximately 790 m below surface and extends to a resource depth of 940 m. Horizontal thickness of the orebody ranges from 10 m to 45 m in width, with the average being 30 m. Previous mining at the Lanfranchi operations specifically the Helmut orebody, had a history of seismic activity. When Panoramic Resources acquired the operation it was decided that seismicity was going to be an issue and therefore a mining method needed to be selected that could effectively manage this potential risk. The dip of the orebody is quite shallow at 45º, with a 30º plunge to the south . The hanging-wall comprises of very weak ultramafics. Due to these factors the orebody posed several mining challenges. To safely and effectively mine the Helmut South orebody in the Lanfranchi Nickel mine, underhand cut and fill mining was selected as the most appropriate mining method. Paste fill comprising of cemented gold tailings was the backfill of choice. This paper is intended to convey some of the key learnings from the use of a mining method that has not been commonly practiced in Australia.

Mar 21, 2011

By P. L. Allsman

A method of analyzing blasting action indicates that major cost savings are possible by revising practice and bringing the classical blasting formulas up to date; difficult problems such as taconite and throw-breakup can be attacked by engineering Denonation pressure — the peak pressure developed by the explosive reaction; "shatter blasting." Average detonation pressure — the average pressure over the time the reaction continues; "heave blasting." Radial presswe — the stress in a radially expanding sphere about the detonation. Corresponds to the diminishing peak pressure. Lateral stress - the stress in a circumferential direction, induced by outward movement of the rock away from the detonation. Limiting stress or Slim— the rock property at which failure will occur in the case at hand; may be tensile or compressive strength, or combinations. Recent developments in explosives technology, following the advent of nuclear explosions, have led to a rather complete understanding of their action. A survey was made for the purpose of uncovering any knowledge which might be applicable in the mining and quarrying industries, the principal users of explosives. Although no revolutionary techniques have become apparent, much basic data pertaining to blasting — fortunately not classified — have been developed by recent research, from which a good general understanding of the process can be derived. It is hoped this explanation of the scientific principles governing explosive action, together with a proposed analysis of blasting practice, will further the development of mining engineering. NATURE OF THE REACTION: The phenomenon of explosion, termed detonation, is in reality a rather complex chemical reaction, and as such is completely explainable by physical and chemical laws. Detonation is characterized by high temperature and pressure, extreme rapidity — often being complete within one microsecond — and most importantly by formation of a shock pulse which accompanies the reaction zone. As with any chemical reaction, there is a critical value of temperature and pressure below which detonation can not occur; this is termed the "critical point". Whereas an explosive substance will decompose slowly at ordinary temperature, with the formation of gases which readily dissipate; at elevated temperature the reaction is considerably speeded. If pressure is suddenly applied at some point in an explosive medium, adiabatic compression results, and the temperature is locally raised. When the temperature becomes high enough the decomposition will be so rapid that the gaseous products do not have time to dissipate, but contribute to a further build-up of pressure. This, in turn, furthers adiabatic temperature rise over a widening area, and with any heat generated by an exothermic reaction, causes a rapid increase in temperature. Both temperature and pressure are spontaneously built up in this manner until the critical point is reached, resulting in detonation. The values of pressure and temperature necessary to create detonation are established by the unusual nature of the process. If temperature alone is raised above the critical point, without sufficient increase in pressure, deflagration or "low-order detonation" occurs. In the true, or "high-order detonation", the shock pulse resulting from the violent decomposition becomes an integral part of the reaction, and itself aids in increasing the detonation

Jan 1, 1961

By D. Limpitlaw

The origins of mine closure practice have influenced the way in which it is implemented by companies and regulators. Mine closure practices essentially started developing in the 1970s in countries with advanced economies and mature mining industries. In these settings, the emphasis was justifiably placed on restoration of the landscape and an attempt was made to return to the ?natural? pre-mining land cover. These practices continued to evolve and incorporated socio-economic and cultural aspects, especially after the Brundtland Report in 1987 and the subsequent Earth Summit in 1992. Today mining is increasingly occurring in remote parts of developing countries where there may be significant need for infrastructure such as roads, clinics, and schools. The costs of returning land to low (economic) value pre-mining use may be far greater than establishing a viable postmining land use that could potentially add value to the community and take pressure off sites for greenfield development elsewhere. Furthermore, natural resource limitations (such as topsoil availability) may limit the degree to which the historical land cover can be re-established. Establishing post-mining land uses may aid in mitigating the loss of employment that is inevitable when mines close. Stakeholder participation in establishing post-mining land cover and land use options is critical for long-term success. Similarly, third parties must be identified to support the development of the post-mining land use This paper draws on the experience of the authors in several developing countries and presents a case for maximizing re-use of mining infrastructure. The paper does not advocate the adoption of poor rehabilitation standards, nor or the wholesale destruction of land capability, but rather leaving key infrastructure in place for post-mining use that may support sustainable development.

Jan 1, 2014

By Warren E. Wilson

THE transportation of solids in pipe lines is a matter of deep concern in many fields of engineering. Much experimental and theoretical work has been done in an effort to devise means of designing pipe lines that will satisfactorily transport given solid loads, but there remain many unanswered questions in this field. The present discussion will be confined to a rather narrow portion of this field and will endeavor to point out certain factors that may well be considered when comparing the relative economy of various installations. The data have been presented previously but a new interpretation was prompted by a suggestion in a paper by Professor O'Brien,1 of the University of California, that the friction work per pound of dry material should be considered in determining the relative efficiency of various installations. This method of considering relative economy in various pipe lines leads to some rather unexpected conclusions, especially with reference to the economy of large pipe sizes. A previous suggestion by the writer3 concerning the economy of a rather peculiar type of installation is strengthened. It is not believed that the considerations set forth herein apply directly in the case of dredge lines, where economy is largely a matter of a high rate of pumping in order to reduce the unit overhead charge. However, it is believed that some value may be gained from these considerations in cases involving the disposal of a fixed amount of solids per unit time with a minimum expenditure of energy and at a low cost for replacement of worn pipes. Such situations are not uncommon in the disposal of mill tailings and the disposal of solids deposited from irrigation waters. It was found that data leading to general conclusions for various pipe sizes were not available but certain definite trends are indicated and methods of analyzing available data are presented in the hope that they may be of assistance in preparing engineering estimates on designs of pipe lines of the type described above. ENERGY. REQUIREMENTS Carrying out the idea contained in Professor O'Brien's paper concerning the method of computing energy required to transport solids, the following analysis leads to some rather interesting conclusions. Let us represent: [Solids load in terms of mass per unit time by W Ratio of mass of suspended solids to total mass of mixture flowing by p Volume rate of flow of mixture by Q Length of pipe by L Slope of energy grade line by s Mass per unit volume of solids by m, Mass per unit volume of liquid by ml Mass per unit volume of mixture by m,,, We then have as an expression for the solids load: W = pQm¬] The work done per unit mass, P, on the mixture to move it along the pipe the

Jan 1, 1945

By E. Peters

Roasting processes are divided into several elementary mechanisms, any of which could be significant or pre-dominant in a particular roast. The elementary processes considered in-elude beat transfer, gas-solid inter-actions with accompanying mass transfer between the bed and furnace atmosphere, vapor phase transport processes in solid-solid interactions, and solid phase diffusion processes. Examples are chosen of processes in which one of these mechanisms pre-dominates and some recently obtained data is presented to support the existence and significance of these mechanisms. Proposals are also made for future research in these areas, and for utilizing the information in the improvement of roaster capacities’ OASTING of ores as a preparative treatment for smelting or leaching has been practiced for so long that its origin has been lost in antiquity, but little has been under-stood of its basic nature until fair-ly recent times. The nominal chemistry of roasting processes is now understood; that is, the initial chemical com-pounds present in the ores or con-

Jan 1, 1961

By A. Smithson

It is generally accepted by British mining engineers that coal will continue to be worked by the. advancing or retreating longwall system for the foreseeable future. At the coal face, the emphasis will be on better machine utilization; increased equipment reliability; modular design and more standardization; remote control and monitoring; and a continuing drive to increase productivity and safety. Improvements at the face can be sustained only if there are corresponding improvements in efficiency elsewhere in the mine. Coal handling systems, for example, must be able to accept increased tonnages without creating bottlenecks. As workings move further from the shafts, the time taken to transport men and materials must be kept within reasonable limits. Development drivages must he on schedule to be ready for the planned opening of new faces, and face ends must keep up with faster moving faces.

Jan 8, 1981

By L. C. St. Arnaud

"Open pit mines can produce large disturbances within regional hydrogeologic systems. The degree of disturbance and the consequences on the local environment depend on the size of the pit and on the physical setting of the mine. Comparisons and contrasts are presented for three Noranda base metal open pit mine sites.The Brunswick Mining and Smelting No 6 open pit has a surface area of 11 ha and a depth of 185 m. It is located within complexly deformed schists and meta-volcanic rocks. The massive sulphide and iron formations visible along the north and southwest walls of the pit generate acid drainage. Mining ceased in 1983, and the pit is presently being filled with waste rock and neutralized drainage water. Water balance calculations estimated a total fill up time of sixteen years. As the water level rises, leakage to groundwater could take place across a fault zone intersecting the pit.The Mattabi Mines F-Group pit has a surface area of approximately 3 ha and a depth of 50 m and is also set in meta-volcanic rocks and acid generating iron formations. Production at this site ceased in 1982, and the low pH pit water is neutralized and pumped into a nearby lake at least every five years. Major water inflows are from precipitation and groundwater. Groundwater mounds within adjacent high land surrounding the pit provide a natural hydraulic barrier to groundwater flow, except for the southeast side. As a consequence, the pit water elevation is being kept below the elevation of the nearby creek in which some of the pit water could drain.The Bell Copper open pit covers an area of 40 ha and is 270 m deep. With present ore reserves, the mine might be in operation until 1992. The geology around the pit consists of andesitic tufts, siltstones and shales, and the acid generation potential of the rock is relatively low. A recent hydrogeological study estimated fill up time by precipitation and groundwater to be in the order of 260 years.With increasingly more stringent requirements for mine closure, it is anticipated that more detailed hydrological and hydrogeological studies of open pits will be required to determine post-closure environmental impacts and the suitability of open pits for mine waste disposal."

Jan 1, 1990

By B. C. F1intoff, R. G. Bradburn, E. Groiss

"The concentrator at Brenda Mines Ltd. treats a copper - molybdenum porphyry ore with current head grades of 0.185% Cu and 0.036% Mo. The consistently low head grades provided the driving force to explore methods of improving plant productivity. Computer based process control was recognized as one means of addressing this objective. Over the period from 1974 to 1982 a control system evolved which now extends to every area of the mill. Control strategies are built on elements of classical, modern and rudimentary expert control. In addition, the control system has often served as a catalyst for other technological developments. The economic returns associated with the system are very significant and it has played an important role in the mine's survival in times of poor metal markets. This paper presents an overview of the computer control system at Brenda.PreambleOne can scarcely avoid picking up a trade magazine or newspaper today without seeing some reference to technology and its potential impact on North American business. _A recurring theme is the need to apply technology to raise our standard of plant automation in the manufacturing and process industries. The general thesis of these articles has been concisely captured in the mutually exclusive set:AUTOMATE or EMIGRATE or EVAPORATEProcess control is one form of automation that has been successfully exploited by various sectors of these industries. In minerals and metal processing the wide scale adoption of process control technology has, until recently, been largely limited to a few companies - most of whom have a history in the area dating back to the early 1970’s. However, there is definitely an increased and much broader interest in process control as a technology which can improve performance, productivity and profit.The economic hardships that were visited on the mining industry in the early 1980's are not easily forgotten. It is the authors' conviction that the mining industry must move to implement proven technology, in particular process control, in order to be well postured for the next (inevitable) down cycle.In pursuing the technical and trade literature, one can discover a number of example of the successful utilization of process control systems in mining and related applications. In the text which follows, the authors describe the process control efforts undertaken in the Brenda Mines Ltd. concentrator."

Jan 1, 1989

By M. Palfreyman

"Most of the minerals employed in Canadian refractory production are imported; in fact, most of the refractories consumed in Canada are imported. Whereas this situation is partly due to a definite shortage of suitable raw materials, e.g., fire clays, it is possible that the potential of certain mineral deposits which could be usefully exploited has not been recognized. There are exceptions, notably magnesite and dolomite, from which refractories are produced in Canada.In many cases, known mineral deposits are located either in inaccessible areas or in areas where transportation would be a major economic factor. This paper lists some minerals and their respective known deposits which could be employed in the production of refractories, irrespective of economics."

Jan 1, 1973

By Brendan Demich, Brendan Macdonald, Timothy J. Orr, Jason Navoyski, Jennica L. Bellanca, William J. Helfrich

Recent advances in computing, rendering, and display technologies have generated increased accessibility for virtual reality (VR). VR allows the creation of dynamic, high-fidelity environments to simulate dangerous situations, test conditions, and visualize concepts. Consequently, numerous products have been developed, but many of these are limited in scope. Therefore, the National Institute for Occupational Safety and Health researchers developed a VR framework, called VR Mine, to rapidly create an underground mine for human data collection, simulation, visualization, and training. This paper describes the features of VR Mine using self-escape and proximity detection as case studies. Features include mine generation, simulated networks, proximity detection systems, and the integration and visualization of real-time ventilation models.

By R. Degel

Keywords: Pyrometallurgy, DC furnaces, electric smelter, FeCr, FeNi, FeMn, Si metal, ferro-alloys, platinum production, circular furnace, energy recovery system In 1906, the first submerged-arc furnace was supplied by SMS Siemag. Since then, the division has become established in various industries such as ferro-alloys and non-ferrous metals, and in numerous other special applications. During the evolution of this technology, more efficient units with longer lifetimes were developed. Today, especially the potential of DC-based smelters, raises worldwide attention, with some projects having already started to implement this kind of technology. This paper evaluates SMS Siemag?s general viewpoint regarding the potential application of DC smelter technology and possible options for the ferro-alloy and non-ferrous industry. SMS Siemag is currently executing a FeCr project in Kazakhstan, where four of the world?s largest closed-type DC smelting furnaces, with a power input of 72 MW, will be installed. These furnaces include the latest technological features of modern DC smelters, which are described in this paper. SMS Siemag has started a long-term research and development project allowing a direct comparison of AC versus DC technology on a large scale, using a recently installed 1 MVA test furnace at the IME at the University of Aachen, in Germany. For open-type ferro-alloy and Si-metal furnaces, SMS Siemag has developed an energy recovery system, which is presented in this paper.

Jan 1, 2011

By THOMAS S. MENNIE

ON GORE Mountain, about four and a half miles, southwest of the village of North Creek, Warren Co., N. Y., are the Barton Mines. Here is the largest known deposit of garnet in the world. This property is owned by H. H. Barton &: Son Co., of Philadelphia, and is being worked under lease by Barton Mines Corpn. North Creek is the terminus of the branch of the Delaware and Hudson R..R., which runs into the

Jan 1, 1925

By M. Ksiazek

Keywords: Thermal conductivity, thermal diffusivity, flash method, specific heat capacity, manganese ore Manganese ferro-alloys manufacturing involves a combination of quality raw materials and an energy source to produce high-quality products with low energy consumption. The thermal properties of manganese raw materials such as ores, sinters, and briquettes, are among the many factors that determine the amount of energy needed for processing. Thermal expansion, thermal diffusivity, conductivity, and apparent specific heat capacity of solid samples and compacted powder samples of manganese ores were examined from room temperature to 1000 °C. The effect of porosity (of the materials used) on the thermal properties was also investigated. The laser flash method and a pushrod dilatometer were used.

Jan 1, 2011

By D. Schleiss

Reduced access to knowledgeable workers is creating challenges for operations. We are doing more 4D Operations - dirty, dull, dangerous, and distant. Personnel costs in these environments are high, and it is not always possible to get the people where you need them. Integrated Operations is a strategy to integrate people, process, and technology for faster and better decision making. Adopting an integrated operations approach can help to relocate personnel, improve collaboration, and align objectives to deliver reduced costs and improved performance. In this paper, the authors will highlight the required infrastructure to enable an Integrated Operations platform. Key decision points for enabling this technology for both Greenfield projects and existing mines will be discussed. Furthermore, the benefits and improved return on investment that result from deployment of an Integrated Operations strategy will be presented.

Jan 1, 2014

By J. Alberto Vázquez M.

A sensor employing yttria-stabilized zirconia (YSZ) was used to determine the oxygen activity of molten copper at laboratory scale at temperatures of 1200° and 1300 dc. The reference electrode was a Ni-NiO mixture. The amount of the deoxidizing agent (CU3P) ranged from I to 3% of the mass of copper. Thermodynamic analysis of the Cu-O-P liquid system was carried out to predict the required deoxidizing agent and the final composition of the molten copper. Both results, calculated and experimental, show that the oxygen removal is more efficient at lower temperatures. The kinetics of the deoxidizing reaction is very fast in the first minutes of the treatment. A metalography analysis of rapid cooled samples show the oxygen and phosphorus distribution

Jan 1, 2003

By José Calderón

Poderosa tiene sus concesiones en las provincias de Pataz y Bolívar en la región La Libertad y son parte de la zona de amortiguamiento (ZA) del parque nacional Río Abiseo (PNRA) y de la zona de transición (ZT) de la reserva de biosfera Gran Pajatén (RBGP). Esta área natural protegida (ANP) es uno de los dos únicos sitios en el Perú que tienen carácter de patrimonio cultural y natural de la humanidad (doble caracterización dada por Unesco). Poderosa ha firmado un convenio de cooperación interinstitucional con el Servicio Nacional de Áreas Naturales Protegidas por el Estado (Sernanp) del PNRA, el mismo que le ha permitido contar con su asesoría, mejorar los instrumentos ambientales y cumplir a cabalidad los compromisos socioambientales.

May 22, 2019