Search Documents

By P. van Meurs, C. van der Poel

From observations of the linear displacement of oil by water from a porous medium as visualized in transparent models, new insight into the mechanism of vircous fingering, as occurring in the case of unfavorable oil-water viscosity ratios, has been obtained. A mathematical description of the observed phenomena leads to formulas. expressing both oil production and pressure drop across the formation as a func-tion of cumulative water injection with the oil-water viscosity ratio as a parameter. Theoretical results are compared with those obtained from scaled laboratory experiments in sand-filled rubes in which water was injected at the one end and production was obtained from the other end. In the second part of the paper the same principles are used to calculate a more realistic production scheme in which production of oil and water is obtained from wells regularly distributed over the field. Results show satisfactory agreement with production data of an actual oil field. Application of the theory is extremely simple as only a limited number of readily available parameters have to be known and results are presented in an analytical form. INTRODUCTION When oil is displaced from a porous medium by water having a viscosity lower than the oil. the oil-water interface is essentially unstable and has the tendency to break up into what are called "fingers" or "streamers". This Viscous fingering has been noted before by Engelberts and Klinkenberg' and has recently been demonstrated in transparent models by van Meurs-. It is highly questionable whether it is at all possible to perform relative permeability measurements In the laboratory reproducing the same distribution of water and oil in the cores as Present in practice. Therefore, we based our descriptive theory on an idealized model which was "tailored" to the fingering mechanism as observed in transparent models under scaled conditions. This approach was the more attractive, as a highly simplified model had already yielded an adequate description of the process. Though we are aware our theoretical approach can be extended in several ways, it is given here in its simplest form to explain the fundamental principles and to avoid complicated formulas. SIMPLEST CASE OF A LINEAR DRIVE Observations and Theoretical Model In Fig. 1 a series of photographs shows how water penetrates into a formation saturated with an oil which is considerably more viscous than the water. The technique for obtaining these photographs, using transparent models, has already been described?. The fingers can be clearly observed and are seen to be mainly parallel to the flow direction. Note that the contours of these fingers are not smooth but show protrusions of water enclosing oil pockets.

By E. W. Dean

In the early winter of 1919 the Pittsburgh petroleum laboratory of the Bureau of Mines undertook the work of testing fuel oil samples representing purchases of the United State Shipping Board for ships sailing from the port of New York. fuel oil was, at this time, being bought on a contract which involved specifications issued by the United States Navy under dace of October 2, 1920 (See Bulletin 1, Oil Division, U. S. Fuel Administration.)The object of the Bureau of Mines in undertaking this inspection work was twofold. (1) The Bureau was in position to give, and the Shipping Board needed, reliable laboratory service for checking the quality of the fuel oil purchased, the value of which ran into millions of dollars for,year's supply. (2) It was believed, and later demonstrated, that the existing specifications did not insure the obtaining of a reliably satisfactory quality of oil.The objection to the specifications concerned the employment of a clause limiting the gravity of the oil. The inadequacy of gravity specifications for several types of petroleum products has long been recognized, and there was every reason to reason to believe that they were no more desirable for fuel oil than for gasoline, kerosene, or lubricating oil. A first and obvious objection was the fact that it is somewhat difficult to make accurate gravity tests on ""heavy"" residuum fuel oils. (The Bureau found it necessary to employ or such tests a rather tedious procedure involving the use of a picnometer and an accurate balance, as the simpler methods, employing hydrometer or displacement balance, proved unreliable in a large proportion of cases.) A second and more important objection was that gravity tests, even when accurately made, do not provide a reliable index of the actual quality of the oil.

Feb 1, 1921

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Variations of cut-and-fill stoping are the most com¬monly used methods for mining narrow, nearly vertical veins in the United States. These methods offer the best results for maximum recovery with minimum dilution of ore from veins that are irregular along either the strike or dip. The vein is developed along the strike length in 61 to 122-m (200 to 400-ft) blocks or stopes and vertical lifts of 48 to 61 m (160 to 200 ft). The level development is either on the vein or parallel to the vein with crosscuts intersecting the vein at right angles. Chutes, manways, and haulageways are established in the center of the stopes at the lower level of the ore block. Mining then proceeds by blasting down horizon¬tal cuts of the vein in both directions from the chutes. As the blasting continues to the outer limits of the stope, the broken ore is slushed into chutes. When a complete horizontal cut has been made, the service raise, including chutes, is raised to a height of a few feet from the back and the stope is filled with either sand fill or waste rock. Then the mining cycle is re¬peated until the stope reaches the level above. LEVEL DEVELOPMENT PRACTICES FOROVERHAND CUT-AND-FILL STOPING The two basic methods used are: the development of the haulage drift within the vein, or development of the haulage drift paralleling the vein in the foot or hang¬ing wall with crosscuts intersecting the vein perpendicu¬larly at 61 to 122-m (200 to 400-ft) intervals. The il¬lustrated methods of development show some of the variations which can be used to develop a stope block. Development for cut-and-fill stoping does not require the more elaborate schemes outlined for shrinkage or sublevel long-hole stoping. Many factors must be considered before deciding on a particular development plan and usually the nature of the vein or host rock will dictate which specific method to use. If the vein is relatively straight, then develop¬ment on the vein is feasible. Excessive ground pressures will necessitate the leaving of a sill pillar (Fig. la) and highly fractured or "heavy" ground will require timber¬ing (Fig. 1b). Development on the vein has the advan¬tage of reducing capital outlay and waste handling prob¬lems since the mined rock has value. But removal of the sill pillar is costly and time-consuming. Also, where no sill pillar is left, excessive timbering and subsequent level repair is a drawback. Development in either the footwall or hanging wall is the more common procedure and offers greater flexi¬bility in overall development of consecutive stoping blocks by partially disassociating the level development from stoping (Fig. 2). Chutes, manways, and service compartments com¬prise the next stage of development and are established in a variety of ways. They provide access to the stope, ventilation ducts, and muck removal. Several different development systems are in common use and average costs for each have been developed. Raise borers are used to establish ventilation and ac¬cess from level to level. They are normally reamed with 1.5 or 1.8-m (5 or 6-ft) cutterhead and may either be left bald or lined with a 1.2-m (4-ft) diam corrugated liner plate, depending upon ground conditions. The use of an Alimak raise climber is another effec¬tive method of driving a raise from level to level. The size usually is 2 m (7 ft) square. This will accommodate square-set timber which is later installed. This method of raising is not common, although it is a valuable tech¬nique especially when level spacing is several hundred feet.

Jan 1, 1982

By B. S. Agbenuvor, R. Morrison, V. Jokovic, C. Antonio

Body breakage usually involves breakage of particles by compression between two surfaces or impacted against a rigid surface, with the latter of interest in this current study. This mode of breakage has been identified to be the most elementary size reduction process and the most effective breakage process in comminution devices. It has been found in the literature that the progenies produced from this form of breakage possess a residual velocity at which they move, after the breakage event. In the pursuit of efficiently utilising applied comminution energy, a laboratory-scale breakage device has been developed to deliver precise specific impact breakage using the concept of a fast-moving hammer and a slow-moving particle to effect breakage. The residual velocities of the progenies from the breakage event may be used to generate secondary breakage without further addition of energy if the particle encounters a stiff obstacle such as a steel plate at right angles to its path. To measure the extent of secondary breakage, the steel wall of the device was lined with a rubber material to suppress the second set of breakage events. The performance of the new device is analysed, based on calculated t10 values and measured residual velocities of the moving daughter particles. Testing involving anvils showed a much finer PSD and higher t10 compared to the test involving rubber lining. This finding is corroborated by the measured residual velocities of the progenies. The resulting energies calculated from the measured residual velocities of the progeny were found to be approximately 42-88% of the primary specific impact energy. This retained energy was found to be sufficient for secondary breakage. Keywords: Impact breakage, residual velocity, secondary breakage, energy utilisation

Jan 1, 2020

Over half of the molten aluminium produced at the 52,000 tons/ year eapacity plant operated by Comalco Aluminium (Bell Bay) Limited in Tasmania is cast into saleable produets by the direct chill process. Considering the importance of direct chill casting to the aluminium industry it is surprising that so little published literature on the subject is available, although Easton (1947), Smart (1954), and Uppert (1940, 1944, 1945) have contributed much toward lifting the veil of secrecy surrounding the process.The direct chill, or D.C. process as it is commonly called when related to aluminium, consists basically of feeding molten aluminium or its alloys into; water-cooled mould from the bottom of which solid aluminium is continuously extracted. Although the casting procedure is continuous in principle, the equipment is normally operated in an intermittent manner. Castings up to 20 ft long are formed during a cycle. At the end of the cycle casting is stopped and the pit into which thc castings are dropped is cleared before a new cycle commences. Depending on the size of the casting in relation to the cross sectional area of the pit and the support mechanism (commonly a hydraulic ram), 'drops' of up to 15 tons are not uncommon. This method of D.C. casting IS termed vertical D.C. casting and is the one most commonly employed in the aluminium industry.Horizontal casting has come more to the fore in recent years with the casting being extracted from the mould in the horizontal plane and is a truly continuous casting method since flying saws can be simply used to cut the continuously cast shape into required lengths as it emerges from the mould...

Jan 1, 1967

By John A. Breslin

Size distributions and concentrations of particulates emitted from diesel engine exhausts were measured with cascade impactors. Samples were taken from the exhaust of two types of engines using three types of fuel and operating under five different engine speed and load conditions. The measured mass median diameters of the diesel particulates were typically about 0.3 um. There was no significant difference in mass median diameter between engines or fuels and only a slight dependence on operating mode. Concentration measurements ranged from 14.2 to 250.9 mg/cu m, and calculated mass outputs, from 52 to 3,443 mg/min. Significant differences in mass output were found between engines, fuels, and especially between different operating modes. The quantity of clean dilution air that would be required to reduce the particulate mass concentration below the 2.0 mg/cu m respirable dust standard for coal mines was greater than the dilution air required to meet the standards for noxious gases for both engines tested.

Jan 1, 1976

By T Albinson

Mexican epithermal deposits can be broadly grouped into two types based on their contained metals, distribution, associated igneous rocks and fluid inclusion compositions. Silver-gold deposits (eg Tayoltita) mostly occur in the western part of northernMexico where host rocks consist of Eocene, intermediate composition volcanic and intrusive rocks; fluid inclusion studies indicate that mineralising fluids were <300¦C and dilute (=3 eq. wt. % NaCl). In contrast, silver-lead-zinc deposits (eg Fresnillo) mostly occur in the central part of northern Mexico where they are temporally associated with Oligocene-Miocene volcanic rocks and intrusions of felsic composition, but commonly hosted within underlying Paleozoic-Mesozoic sedimentary rocks; fluid inclusion studies indicate that mineralizing fluids ranged from 200 to 400 ¦C and were saline (=10 eq. wt. % NaCl). The distribution of these two deposit types, crosscutting major crustal sutures, and the close spatial-temporal relationships between mineralisation and magmatism, together suggest that magmatic processes were more important in the formation of mineralising solutions, as a source of both ligands and metals, than the segments of crust hosting deposits.

Jan 1, 1995

By John A. Breslin

Size distributions and concentrations of particulates emitted from diesel engine exhausts were measured with cascade impactors. Samples were taken from the exhaust of two types of engines using three types of fuel and operating under five different engine speed and load conditions. The measured mass median diameters of the diesel particulates were typically about 0.3 um. There was no significant difference in mass median diameter between engines or fuels and only a slight dependence on operating mode. Concentration measurements ranged from 14.2 to 250.9 mg/cu m, and calculated mass outputs, from 64 to 10,000 mg/min. Significant differences in mass output were found between engines, fuels, and especially between different operating modes. The quantity of clean dilution air that would be required to reduce the particulate mass concentration below the 2.0 mg/cu m respirable dust standard for coal mines was greater than the dilution air required to meet the standards for noxious gases for both engines tested.

Jan 1, 1976

Karl L. Fetters moves to the front of the AIME organization this month as the 1964 President of the Institute. He will take the chair vacated by outgoing President Roger V. Pierce at the Annual Meeting in New York, already well-rehearsed in his forthcoming duties after a year of preparation as AIME President-Elect. Dr. Fetters is highly qualified for his new responsibilities on both the administrative and professional level. For the past five years, he has been vice president for research and development at The Youngstown Sheet and Tube Co. in Ohio, where he has achieved wide recognition as an out- standing metallurgist and executive. A native of Alliance, Ohio, he obtained his early education in the public schools of his home town and displayed a singular precocity when he launched his professional career as a chemist for the Morgan Engineering Co. at the age of 16. His new career, however, was soon set aside in favor of four years of higher education at the Carnegie Institute of Technology, whence he emerged in 1931 with a bachelor's degree in metallurgical engineering. Surprisingly, and perhaps owing to the employment stringencies of the Depression years, the first job his new qualifications earned him was that of stationary engineer at the Cunningham Sanitarium in Cleveland. After two years of ministering to the mechanical ailments of this institution, Dr. Fetters relinquished his post for a more suitable one in the field of metallurgy.

Jan 2, 1964

By Kirk Ellison, Eric S. Lindquist, Peter Faust, Stephen M. McLandrich

"The 181 Fremont Tower will be an 800-foot high-rise with a 60-foot deep basement located in a dense urban part of downtown San Francisco. The design and construction methods of the subsurface elements navigated a variety of site constraints such as loose fill and soft estuarine soils, shallow groundwater, contaminants, historic obstructions, small work area, proximity of adjacent buildings, and the on-going excavation and build-out of the adjacent Transbay Transit Center (TTC) train box. Design of the approximately 260-foot-deep drilled shafts (some of the deepest foundations ever constructed in San Francisco) was proven by a full-scale load test that provided unique data on the frictional capacity of the deep soil and Franciscan Complex bedrock in the region. Design and construction of the shoring system for the 5-story basement excavation was exceptionally challenging because of the on-going construction for the TTC. To allow for flexibility during construction, hydraulic rams were placed in a transfer waler along the shared TTC shoring wall that could adjust the forces transferred through to the TTC excavation if required. Open and steady communication between the shoring engineer, the geotechnical engineer, and the shoring/foundation contractor was crucial in order to satisfy the complex constraints of this site.INTRODUCTIONThe 181 Fremont Tower is a new build mixed-use tower, currently under construction in the dense urban core of the South of Market District of San Francisco, California. This high-rise will consist of 54 above ground floors with the roof level 700 feet high. Atop the roof will be some architectural features including a spire that will top out at just over 800 feet, which will make it the second tallest building in San Francisco upon completion.The tower is being developed by Jay Paul Company and the architectural design is by Heller Manus. The structural engineer and geotechnical engineer for the project is Arup North America Ltd (Arup). The shoring designer is Brierley Associates (Brierley). The general contractor is Level 10 Construction (Level 10) and the specialty foundation contractor and excavation contractor is Malcolm Drilling Co., Inc (Malcolm)."

Jan 1, 2017

By Nam-Il Um

Bottom ash contains several ferrous materials (ferrous metals, Fe3O4, Fe2O3, FeS, etc.). In particular, ferrous metals contain heavy metal because Ni and Cr are chemically attracted to iron. Likewise, Cu is used to coat Ni and Cr metals as polish or to prevent corrosion. In this study, an Fe3O4-Fe2O3 double layer (similar to pure Fe) was found to have been formed in ferrous metal during air-annealing in an incinerator (1000°C). A strong thermal shock such as one that occurs during the water-cooling of bottom ash results in the breakdown of this oxidation layer, facilitating the degradation of ferrous metals and formation of corrosion products. Therefore, Fe-ion (heavy metal) oxides may be formed on ferrous metals and may be separated from bottom ash via magnetic separation. This study sought to investigate the separation ratio of heavy metals as magnetic separation and mineralogical formation of Fe-ion (heavy metal).

Jan 1, 2006

By Garry M. Johnston, Matthew L. Sutcliffe, Nicholas J. Welham

"The predominant current processes for the treatment of oxidized copper–cobalt ores use a reductive acid leach to bring the desired metals into solution. However, the indiscriminate nature of acid leaching results in a solution, akin to a metal soup, containing not only the Cu and Co but also an extensive suite of other metals. These other metals, notably Fe, Mn, Al, Ca, Mg and Si, all have to be eliminated from solution before the copper and cobalt can be recovered. Generally precipitation processes are used, but these tend to result in significant losses of copper and/or more usually cobalt from solution, leading to reduced recoveries. The AmmLeach® process uses ammonia-based chemistry to selectively leach the target metals, leaving the rest behind in the leach residue. This approach eliminates any need to clean the solution of unwanted metals and the consequent metal losses. After solid–liquid separation, the leach solution is immediately subjected to separation and concentration of the copper and cobalt using solvent extraction and electrowinning. INTRODUCTION The Copper Belt extends through the northern part of Zambia and the southern province of Katanga in the Democratic Republic of Congo (DRC) and contains the richest and highest grade deposits of copper and cobalt remaining in the world. Whilst there are a number of mines that produce sulphide concentrates, using froth flotation, the largest deposits are those where near-surface sulphides have been weathered over time to form oxides. The oxides cannot be concentrated by conventional physical means to give high recoveries. Despite this, a number of dense medium separation plants have been installed and used to produce a higher grade concentrate which is typically exported (while the rejects, typically 2 to 3% Cu are stockpiled for treatment at a later date). These plants generally have low recoveries and can only be used on the dwindling supply of high grade materials. In exporting the concentrate, little value adding is undertaken within the country, thus greatly reducing the economic benefits to the country. Recent changes to the regulations in the DRC will effectively ban the export of low value ores, concentrates and intermediates in favour of high value metals. This will necessitate mines to install new processing circuits in order to comply with these regulations. The head grade of ores currently being treated in the DRC is slowly decreasing as the extremely high grade materials are being selectively mined out. In many cases, the removal of a small volume of high grade materials leaves a much larger volume of economically marginal ore behind. This is due to a desire for short-term profits overtaking long-term prosperity. The remaining ore, which in many cases is still of relatively high value by world class standards, is likely to be only treatable by low cost heap leaching. There are some initial trials of heap leaching within the DRC, but implementation at a large scale has yet to be adopted."

Jan 1, 2015

By George W. Sheary

Situated 45 miles west of Philadelphia and 50 miles southwest of Bethlehem Steel Company's Bethlehem plant, the integrated Grace mine facilities produce 4000 tpd of high-quality iron ore pellets. Startup of the Grace mill was in November 1958, and iron concentrates were shipped until March 1960, when the pellet plant went into operation. The underground mine, when fully developed, will hoist about 9000 tpd, including development rock. The crude ore, which has an iron content of approximately 42%, is magnetically cobbed and crushed in closed circuit with 3/4-in. slotted vibrating screens. The ore is washed and screened in the mill and the plus 1/4 in. screen product is again cobbed prior to feeding to the rod mills. Grinding is done in rod mills, and in ball mills that are in closed circuit with 30 in, cyclones, to 1% on 100 mesh and 65% minus 325 mesh. The ground ore is magnetically concentrated by three-drum permanent type finisher magnets to 67% Fe. The magnetite concentrate is pumped from the mill to a 50 ft thickener in the pellet plant. The thickened magnetite concentrate is relayed to the filters through a two-stage pump arrangement. The filter cake is fed by belt from filter concentrate bins to mixer-muller belts where it is intimately mixed with bentonite and a slight amount of water for moisture control. The fluffed concentrate then drops into balling cones. The green pellets from the balling cones are fed in a prescribed feed pattern to shaft furnaces through the use of shuttle car mechanisms. The green pellets are dried, heated to 2500°F and cooled to 1200°F as they descend through the furnace and into pellet coolers where the pellets are further reduced in temperature to 250°F. Heat is recovered in the cooling process through the use of air-to-air heat exchangers. The cooled pellets discharge on a rubber conveyor belt and are transferred to 6000-ton pellet railroad loading bin. The final pellet product consists of 90% plus 1/4 in. material (after tumble testing1) and contains 66% Fe plus 3% silica.

Jan 5, 1962

By F. Cihangir, A. Kesimal, K. Karaman, B. Ercikdi

Uniaxial compressive strength (UCS) and shear strength parameters(cohesion and angle of internal friction, Cand F) of rocks are important parameters needed for various engineering projects such as tunnelling and slope stability. However, direct determination of these parameters is difficult and requires high-quality core samples for tests. Therefore, this study aimed to explore the applicability of the Brazilian test (BT) - a simple, less sophisticated and inexpensive method for both specimen preparation and testing - to estimate the UCS and shear strength parameters of rocks. Thirty-seven rock types were sampled and tested, 24of which were volcanic, 8 were metamorphic, and 5 were sedimentary. Statistical equations were derived to estimate the UCS and shear strength parameters of rocks using the BT. The validity of the statistically derived equations was confirmed using predictive analytics software (PASW Statistics 18). A strong linear relation was found between BT and UCS values. BT and UCS values exhibited prominent linear correlations withthe cohesion values of rocks. The Mohr envelope was also used to determine the cohesion and friction angle of rocks using BT and UCS values. It is deduced from the current study that the BT values can be used to estimate the UCS and cohesion. However, no relation was observed between the angle of internal friction values and the UCS and BT for all rock types. Therefore, different approaches are suggested for the estimation of the internal angle of friction for application in the preliminary design of projects.

Jan 1, 2015

By J. J. Gusek

The Riley Pass strip mine is an abandoned uranium-bearing lignite deposit in Harding County, South Dakota, covering about 150 acres of highwalls, pit floor and mine spoils exhibiting elevated levels of radioactivity. Six reclamation design alternatives were developed, ranging from doing nothing to reclaiming to approximate original con-tour. The alternatives were evaluated for expense, site stabilization, and mitigation of public safety hazards. A comparative economic evaluation on three of the alternatives was completed for the Forest Service in selecting an alternative and substantiating federal funding requests. This evaluation included economic impacts associated with physical and radiologic health hazards, affects on recreational users, socioeconomic impacts and environmental improvement.

Jan 1, 1995

By Dara L. Hrytzak-Lieffers

Canada has long since been a place that has led the world in mining development, in a safe, clean, and sustainable manner. This has led to the integration of corporate social responsibility (CSR) philosophy in corporate governance, policy, and programming. The paper will identify the basis of CSR practise in Canada?s mining industry and provide a Canadian example of CSR implementation. Biography Dara Hrytzak-Lieffers is the manager, corporate social responsibility at Cameco Corporation. She oversees corporate CSR initiatives including the Sustainable Development report and public engagement programs. Dara received her BA in International Studies from the University of Saskatchewan and an MA in International Conflict Analysis from the Brussels School of International Studies. She is a recent graduate of the World Nuclear University summer institute.

May 1, 2011

By Manca PP, Rossi G, Lipari D, Knissel W, Massacci G, Licheri P, Fioravanti E, Helms W, Lai S

Mining of the massive complex sulphides orebodies of Campo Pisano and San Benedetto (Southern Sardinia, Italy), dates back to before Christ, though their exploitation with modern technology was only resumed in the middle of the last century. The increasingly adverse economic conditions and the weakness of both country rock and mineralization were concurrent in forcing the Company's management to develop suitable high-productivity stoping methods. In the framework of a project fi- nanced in part by the Commission of the European Coranunities, and carried out in cooperation with the Universities of Cagliari (Italy) and Clausthal (Germany), a cemented backfill stoping method was developed. The concrete mix preparation and placement facil- ities, study of the cement mixes and endeavaa-s to optimize the methods are described. The monitoring system for measuring stress evolution within the emplaced backfill is illustrated together with the successful replacement of part of the Portland cement

Jan 1, 1992

By Robert C. Ellman

Stockpiles containing 2.3 million tons of lignite constructed in the period 1948-56 in conjunction with the construction of Garrison Dam on the Missouri River demonstrate successful stable long-term storage of lignite. Uniform and thorough compaction of each of the I-foot-thick layers by which the piles were constructed produced a bulk density of 70 Ib/cu ft. Air penetration into the stockpiles was restricted to a degree that prevents spontaneous heating or deterioration of the stored lignite, A continuing record of observations beginning with stockpiling operations in 1948 has been accumulated, This includes periodic fuel analysis, analysis of pile gases, and measurement of pile temperatures on the first large stock-pile, pile 5. This report describes the stockpiling method, the changes in heating value, pile gas composition, and pile temperature and summarizes observations from 1953 to 1964, Data accumulated attest to the stability of the stored lignite. The variation of the average heating value of periodic pile-depth samples is only 160 Btu/lb (11,990 to 11,830) on the moisture" and ash-free (maf) basis during almost 10 years of storage. Temperature levels of the pile interior are progressively decreasing. At pile surface, cyclic variations occur with the season. The only problem encountered with the large stockpiles is wind and water erosion of the pile surface. The partially successful control measures used are described.

Jan 1, 1967

The ~2500 km long Kermadec-Tonga arc northeast ofNew Zealand is the longest continuous intraoceanic arc in the world. At least 94 volcanic centres along the arc are submarine, most (87 per cent) within the Kermadec arc (de Ronde et al, 2003a). Volcanic rocks range from basalt to rhyodacite with trace element and isotopic data indicating significant magma source heterogeneity both along and across the arc.   The entire ~1300 km of the Kermadec arc has now been surveyed for hydrothermal emissions (de Ronde et al, 2004). First-stage surveys utilised surface vessels. In February 1996, the first sulfide samples from the southern Kermadec arc were dredged from the Brothers and Rumble II West caldera volcanoes (R/V Tangaroa cruise TAN96/03; Wright et al, 1998; de Ronde et al, 2003b). In September 1998, low-temperature, diffuse venting was discovered at Monowai, Rumble III and Clark volcanoes, and high-temperature, black smoker venting was found within Brothers caldera (R/V Sonne cruise SO-135; Stoffers et al, 1999). The NZAPLUME cruise of March 1999 surveyed 13 volcanic centres (each mainly comprised of single, large volcanoes) of the southern Kermadec arc and documented hydrothermal emissions above seven of them (de Ronde et al, 2001; Baker et al, 2003; Massoth et al, 2003). In July 2001, additional mineralised and hydrothermally altered samples were dredged from Brothers volcano (R/V Tangaroa cruise TAN01/07). The NZAPLUME II cruise of May 2002 confirmed venting was still occurring at all the known hydrothermal sites, and that ten active vent sites occurred along the mid-part of the arc, between Brothers and Raoul Island (de Ronde et al, 2002). In September-October 2004, NZAPLUME III surveyed the northern-most part of the Kermadec arc where another nine volcanic centres are hydrothermally active.   Second-stage exploration of the Kermadec arc hydrothermal systems utilised deep submergence vehicles. In October-November 2004, the Japanese submersible Shinkai 6500 made four dives on Brothers. Samples recovered include vent fluids, chimneys, altered rocks and various animals and microbes. In April-May 2005, a more extensive expedition using the American submersible Pisces V made 23 dives on nine different volcanic centres, eight of them for the first time.   Extensive plume surveys show Brothers volcano is host to the most hydrothermally active sites of all those known along the Kermadec arc. In total, nine dives have been made on Brothers, six on the NW caldera site and three on the cone site. The NW caldera vent site is a long-term hydrothermal system that is today dominated by evolved seawater but has had episodic injections of magmatic fluid. The cone site is a nascent magmatic-hydrothermal system where crack zones localise upwelling acidic waters (de Ronde et al, 2005). A SE caldera site represents the main upflow of a relatively well-established magmatic-hydrothermal system on the seafloor where sulfide-rich chimneys are extant. Each of these different vent sites represent diverse parts of an evolving hydrothermal system, any one of which may be typical of submarine volcanic arcs.

Jan 1, 2005

By R. L. Atwood

This paper discusses the metallurgical and Manufacturing input to Merrill-Crowe plants. Topics treated are pregnant solution chemistry, clarification, degassing, zinc addition, product filtration, accounting, and costs.

Jan 1, 1985