Search Documents

By E. C. Bitzer

THE primary object of the work described in the following pages was to simplify the equipment in the separating circuit of the heavy-media process by substituting a spiral classifier for the separatory cone. Mechanical considerations were the leading attraction and the best that was hoped for on metallurgical performance was that the new vessel would give results equal to those obtained by conventional equipment. Tests have demonstrated in commercial operation on iron ore that the mechanical advantages of the spiral separator are about as predicted; also, the metallurgical performance is superior to the cone on the ores treated. Treatment of iron ore involves the separation of two products: a concentrate that sinks and a float product that contains true float material plus a controlled division of interfering middling. The middling material is heavier than the average specific gravity of the separating medium. Recent work with the spiral separator on Tri-State zinc ore showed that the middling material had to be recovered as concentrate because this fraction contained the bulk of the-zinc in the ore. It has been demonstrated that it is possible to make three products with the new separator on an ore such as this: a float tailing, a float middling, and a high grade heavy sink product. It appears from this last work that the new separator has definite mechanica1 and metallurgical advantages over any type of separating cone for treating feed that contains large amounts of material of a specific gravity close to that of the separating medium. However, either type of separator should perform equally well, metallurgically, on feed that is free of middlings. Each series of experiments with the spiral separator as required additional work to fully develop the possibilities of the machine. For this reason the paper is divided into chronological parts. History of Development A drag-type classifier was first proposed as a substitute for the cone separator by Butler Brothers technicians during the initial tests with galena medium at Crosby, Minn., in 1937. The desire for finding a substitute for the cone arose from trouble with interfering middlings and certain operating disadvantages of the cone. The possibility of using a spiral classifier was also suggested at this time by Emmett Butler and C. J. Abrams. However, inability to satisfactorily recover fine galena, which was used as a medium, terminated all development work at Crosby. During the winter of 1937--1938 investigation started on magnetic medium with concurrent s development of the inverted or closed- top cone, which was found necessary to eliminate iron-ore middlings with the float product. About

Jan 1, 1947

By T Walkemeyer, R Elliott, D Chang-Martin

Over the past decade, discrete element method (DEM) simulations have seen increasing adoption by the resources sector to inform the design of materials handling equipment such as transfer chutes, bins and hoppers. But, if ‘all models are wrong, but some are useful’ (Box, 1979) what approaches are available to check that a DEM simulation is useful? How to avoid garbage in equals garbage out. This work considers what properties of bulk solid flow behaviour are important to transfer chute simulation. Cohesive bulk solids (such as sticky iron ore fines) can develop sufficient strength to form a stable cohesive arch, this phenomenon is not well predicted by measurements of angle of repose. This work presents a two-part approach to the development of a useful DEM model that can be used to add value to the design and optimisation of bulk materials handling equipment. Part 1 is the calibration of not just one, but a range of material models chosen to envelope the range of anticipated materials that will be handled. This work describes the DEM simulation of a batch of direct shear cell tests to develop material models that can be measured by the same metrics routinely used to characterise the flowability of cohesive iron ore fines. Part 2 of this work describes systematic methods for validation of the transfer chute DEM simulations. The DEM model is only useful if it can adequately represent the typical problems observed within a transfer chute, such as blockages due to build-up and cohesive arching. Proper validation requires good observations. Validation examples of site observations are shown side-byside with simulations to demonstrate the adequacy of the DEM model and calibration approach. DEM simulations have the potential to add significant value by allowing engineers and designers to predict material flow-through equipment based on a range of material properties, allowing for stress testing designs and making iterative improvements.

Sep 18, 2023

By Xie Zhang, Jiang Diao, Xin Qiu, Lu Jiang, Bing Xie, Hong-Yi Li

"Duplex converter process, in which the first converter is used for removing phosphorus from hot metal (De-P), is an important way to produce low P-content and ultra-low P-content steels. In order to improve phosphorization removal and formation of slag with high basicity at relatively low temperature during dephosphorization converter process, effects of temperature, silicon content in hot metal and varied compositions of the De-P converter slag on phosphorus distribution between the slag and hot metal were investigated with thermodynamic calculations and by laboratory scale experiments in present work. Results showed that phosphorus distribution ratio between slag and metal was varied in 10.6~26.6 when basicity of the slag was in the range of 1.5~2.1 at 1370, and the distribution ratio was increased with increasing basicity and Fe10 content in the slag.IntroductionIt is known that phosphorus exists in steel in the form of solid solution, which can significantly improve strength and hardness of steel at room temperature. However, the plasticity and toughness of steel, especially the low temperature plasticity is sharply reduced and leads to high ductile-brittle transition temperature. This phenomenon is commonly known as cold brittleness of steel [1~3]. Hence, phosphorus should be removed as much as possible in the steelmaking process, because it is generally harmful to the iron and steel products."

Jan 1, 2013

By S. Sarac

Solving ventilation networks of natural splitting is a basic problem in mine ventilation. Several mathematical techniques are used to solve this problem. This paper proposes a new method which combines the advantages of both classical Hardy Cross method and unconstrained optimization techniques. The trials carried out on model networks have shown that the method offers some facilities in the analysis of mine ventilation networks. Keywords: Ventilation network analysis, Hardy Cross method, Steepest Descent method.

Jan 1, 2000

By Paul D. Tomlingson

Numerous worthwhile benefits accrue to the industrial organization that is supported by a maintenance organization performing at a world class level. That organization will be favored with consistently reliable production equipment. It will be assured of meeting production goals. Its product will exceed marketplace standards. Its customers will see them as a quality organization. Its employees will enjoy job satisfaction and the plant will realize continuing profitability. Every industrial plant aspires to achieve ?world class? status knowing it can compete favorably with the best, most profitable organizations in the world. The trick is to achieve the attributes that qualify your organization for world class status. But there are no world class maintenance organizations. Rather, there are world class industrial organizations that include a world class maintenance organization. Maintenance, by itself, is a service provider, dependent on the support and cooperation of other departments. When that service is exceptional, it is made that way because maintenance is operating in a plant environment that requires it to be exceptional. Managers have created an environment in which maintenance can be exceptional. The plant, mine or facility manager must acknowledge from the start that maintenance is not a stand-alone effort of a plant maintenance department. It will require the joint efforts of all plant departments. Quality material support and full cooperation from operations, for example, are among the essential requisites for effective maintenance and achievement of world class maintenance status. When attributes such as these are reinforced by dedicated plant managers, profitability soon follows.

By G. H. Harris

The flotation behavior of two high sulfur coals using a non-ionic surfactant as collector from two series of compounds containing oxygenated functional groups was studied in detail using a 2-liter Denver flotation cell. The performance of these reagents was compared with that of an oily collector, namely dodecane. The results showed that at the same coal recovery, a much lower dosage of these non-ionic surfactants was required as compared with that of dodecane. More import was the performance of these compounds as promoters for oxidized as well as un oxidized coal. Mechanisms of interaction of these compounds with the coal are suggested.

Jan 1, 1993

By E. C. Bitzer

The primary object of the work described in the following pages was to simplify the equipment in the separating circuit of the heavy-media process by substituting a spiral classifier for the separatory cone. Mechanical considerations were the leading attraction and the best that was hoped for on metallurgical performance was that the new vessel would give results equal to those obtained by conventional equipment. Tests have demonstrated in commercial operation on iron ore that the mechanical advantages of the spiral separator are about as predicted; also, the metallurgical performance is superior to the cone on the ores treated. Treatment of iron ore involves the separation of two products: a concentrate that sinks and a float product that contains true float material plus a controlled division of interfering middling. The middling material is heavier than the average specific gravity of the separating medium. Recent work with the spiral separator on Tri-State zinc ore showed that the middling material had to be recovered as concentrate because this fraction contained the bulk of the zinc in the ore. It has been demonstrated that it is possible to make three products with the new separator on an ore such as this: a float tailing, a float middling, and a high- grade heavy sink product. It appears from this last work that the new separator has definite mechanical and metalluigical advantages over any type of separating cone for treating feed that contains large amounts of material of a specific gravity close to that of the separating medium. However, either type of separator should perform equally well, metallurgically, on feed that is free of middlings. Each series of experiments with the spiral separator has required additional work to fully develop the possibilities of the machine. For this reason the paper is divided into chronological parts. History of Development A drag-type classifier was first proposed as a substitute for the cone separator by Butler Brothers technicians during the initial tests with galena medium at Crosby, Minn., in 1937. The desire for finding a substitute for the cone arose from trouble with interfering middlings and certain operating disadvantages of the cone. The possibility of using a spiral classifier was also suggested at this time by Emmett Butler and C. J. Abrams. However, inability to satisfactorily recover fine galena, which was used as a medium, terminated all development work at Crosby. During the winter of 1937--1938 investigation started on magnetic medium with concurrent development of the inverted or closed-top cone, which was found necessary to eliminate iron-ore middlings with the float product. About

Jan 1, 1949

By Steve Collinsworth, Nils Heinke

In 1989, I realized the definite need for change in the Blast Hole Drilling Industry. With over 25 years of experience in dealing with the industry, I am well inGormed and educated concerning the problems that occur in Blast Hole Drilling. After continues interaction with the Drill & Blast Superintendents, Drillers, Purchasing Agents, Mechanics, and others in the field, a basic understanding was developed as to the origins of the main problems that the industry f&s with their drillings programs.

Jan 1, 1997

By A. S. Macfarlane

The introduction of new technology into mining operations is seen as a strategic necessity by many mining companies, in order to improve safety and to improve operational effectiveness. Many attempts have been made in recent years to introduce new technologies into mining operations in southern Africa. Amongst these are noteworthy successes, as well as some disappointing failures. Often, the reason for failure does not lie with the technology itself, but with the work system into which the technology is introduced. Such failures may come with a significant opportunity cost, and have a detrimental effect on future development, simply because the system has not been adequately engineered, and the risks have not been adequately assessed and managed. This paper examines the reasons for such failures, and proposes a methodology to be followed to ensure successful and sustainable implementation of new technologies, such as to reduce technical and financial risk to the company, and to energize the workforce into ensuring the initial objectives of the project are met. The paper also focuses on the application of appropriate technology, and the development of technological applications which are commensurate with the level of development of the work environment into which it is introduced. The paper therefore focuses on the application of risk management, change management, systems engineering and feasibility analysis as being key elements of a successful and holistic technology implementation programme.

Jan 1, 2001

By N. M. Soonawala

Detailed regional geophysical and geochemical surveys, ground surveys and drilling were undertaken to follow-up the federal-provincial Uranium Reconnaissance Program (URP) over the 27,OOO-km2 Kasmere-Munroe area in northwestern Manitoba. An analysis of the URP data showed a fair correlation between the regional airborne radiometric results and lake-bottom geochemical results, both of which also correlated with the regional geology. More detailed surveys defined anomalies with greater precision within the broad zones outlined by the URP. The ground follow-up indicated that URP anomalies can be caused by varying degrees of uranium concentration in the rocks. Mineralization of interest was found in leucogranites at several locations within the survey area. Anomalous uranium concentrations were also found in coarse pegmatites and Hudsonian granitic intrusions. It can be concluded that large-scale regional surveys can be followed up in relatively short periods of time to yield meaningful results if a properly planned exploration sequence is employed, each stage of which successively narrows the area of interest.

Jan 1, 1979

By Marc Boyer

Modern civilization, modern industry, and modern standards of living, bring into, sharp relief the present-day essentiality of metals .and minerals, and the wide and diversified use which is made of them. Any attempt, therefore, to appraise the international situation today must take into consideration the metal and mineral resources of the world. If, as some believe, the world is divided into two distinct ideologies of political belief, one unalterably opposed to the other, so that armed conflict is unavoidable, then the question of national strength in mineral resources becomes of paramount importance. If, however, it is possible to avoid war by raising the standard of living in the underdeveloped ?areas of the world, thus ensuring all peoples everywhere against the dread spectres of starvation and disease, then the development of the world's mineral resources assumes even greater importance. Today it is difficult to realize that, prior to the industrial revolution in Great Britain, only a few of the metals and minerals now in common use entered into the everyday life of the people. !iron and steel, copper, lead, tin, and zinc, usually in .their unalloyed forms, along with the more common industrial minerals, were those most widely used, and then only in limited amount. With the advance of technology in metallurgy and in fabricating skills, the list of commercial metals and minerals has expanded until today they number more than eighty.

Jan 1, 1951

By D Reid, J Black

The adverse health impacts from diesel particulate matter (DPM) exposure are a well-known global concern. The building evidence has triggered underground mining operations to review existing atmospheric conditions and assess the scale of the challenge faced. South32’s Cannington Mine (Cannington) evaluated the ability to provide a healthy atmosphere from a whole mine approach, taking into account existing preventative controls including: maintenance strategies, fuel quality, mining operations, ventilation provisions, monitoring protocols and effective education and training programs.During the evaluation process, Cannington gave due recognition to the advice and guidance provided in the Queensland Guidance Note 21 (QGN21), the Guidelines of New South Wales’ MDG29 and Mining Industry Advisory Committee (MIAC) of Western Australia. Each of these documents advises a dilution rate of >0.06 m3/s/kW is best for reduction of DPM exposure in underground mines.Achieving the prescribed mine ventilation rate typically results in the need to directly invest significant capital into increasing ventilation infrastructure in order to further dilute contaminants. In today’s economic market of volatile metal prices and increasing pressures to meet regulatory requirements, it can become challenging for established metalliferous operations to create a balance between optimisation of current ventilation infrastructure and capital outlay.In order to obtain and correctly justify the requirements for capital investiture Cannington conducted a ventilation operational analysis for the life-of-operation, identifying the existing air volume envelope was adequate for current and future production rates by optimising existing primary ventilation infrastructure through the implementation of a modified ventilation on demand (VoD) and air conservation system.This process achieved sustainable operating and capital cost reductions without compromising delivery of adequate ventilation to work areas. The process also recognised that engaging mine workers’ ownership of their work areas is crucial to maintaining a technically efficient and operationally robust ventilation system.This paper will concentrate on Cannington’s existing preventative controls, their implementation and their management for the prevention of increased DPM exposure; reducing the risk of both short and long-term health impacts to ‘as low as reasonably achievable’ (ALARA).CITATION:Black, J and Reid, D, 2017. Delivering a healthy atmosphere underground in a cost-conscious environment, in Proceedings Australian Mine Vent Conference 2017, pp 159–168 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By A. Norori-McCormac

"Air recovery, the fraction of air entering a flotation cell that overflows the cell lip, is linked to flotation performance, and it has been shown through industrial testwork that operating flotation cells at air rates that yield the Peak Air Recovery (PAR) results in high mineral recovery. For operating parameters over which flotation plants have little control, such as particle size, investigating the effect on the position of PAR, and the subsequent effect on flotation performance, proves more challenging. To this end, we have developed a bench scale flotation system that runs continuously and exhibits froth behavior similar to that found industrially, allowing the study of such parameters as particle size in addition to air rate. The bench scale system comprises a 4 l baffled cylindrical flotation cell, stirred by a Rushton impeller. The concentrate is recycled back into the pulp, allowing for continuous operation. Glass beads are used as solid particles, allowing a wide range of particle sizes to be tested, with TTAB as collector and MIBC as frother. The system allows operation at air rates typical of industrial flotation systems (1 -2 cms-1 superficial gas velocity), in addition to yielding a froth that coalesces and bursts and exhibits a peak in air recovery as cell air rate in increased. Solids and water recovery is also measured. The results show that air recovery is sensitive to changes in particle size. The intermediate size distribution showed a peak in air recovery (PAR) that corresponded with the maximum solids flowrate, as found industrially. It is shown that finer particles do result in more stable froths and higher recoveries, particularly at low air rates. The effect of particle size on the position of PAR is not yet unequivocally determined from these results."

Jan 1, 2014

By W. Denham Verschoyle

In designing a pocket instrumeut whereby any giver1 horizontal or vertical angle may be closely approximated, the following points should be kept in view, if general utility is aimed at : 1. The instrnment should be light and compact, so that it can be carried in the pocket, or in a sling. 2. It should be capable of observing any angle whatever, horizontal or vertical. 3. Since time is often an important consideration in making a preliminary survey, it should be capable of giving the horizontal and vertical angle at one observation. I do not know of any instrunlent that will fulfill these requirements, except the one here described. Where the depression- or elevation-angle of the distant object, whose bearing is required, exceeds 50 or 60 degrees, it becomes difficult or impossible with a prismatic compass, for instance, to obtain accurate results; and since it frequently happens, particularly in mining, that much work requires to be done beyond that limit, it is obvious that an instrument which can be used to observe a high angle just as easily as a low one, if not absolutely a necessity, will at least be a great convenience. How this a pocket transit" attains to the required degree of universality will be understood from the diagram, Fig. 1, in which B is a beveled, graduated circle, attached to and freely revolving about the center of the magnet A. Light falling on B is reflected through a window in F (the compass-box), along the line AC, and is again reflected back to the eye at D by the prism C. By a simple arrangement, the tight-line BCE call be completely revolved in the vertical plane DE, which is normal to AC. It is clear, then, that no matter through what vertical

Jan 1, 1908

By G. Laing

On scheduled commissioning and effective operation of a solvent extraction circuit relies on getting the design of both the core contact equipment and the peripheral plant right. Experience has shown that poor performance of new plants is frequently a result of ?utility? systems that do not match the requirements of the circuit, rather than the mass transfer equipment itself. Both the operator/owner and designer need to understand the ?complete requirements? for the circuit to get the balance of the design right. This paper reviews generic issues, frequently overlooked or altered during cost-cutting exercises, which have a significant impact on plant performance.

Jan 1, 2002

By W. Denham Verschoyle

IN designing a pocket instrument whereby any given horizontal or vertical angle may be closely approximated, the following points should be kept in view, if general utility is aimed at 1. The instrument should be light and compact, so that it can be carried in the pocket, or in a sling. 2. It should be capable of observing any angle whatever, horizontal or vertical. 3. Since time is often an important consideration in making a preliminary survey, it should be capable of giving the horizontal and vertical angle at one observation. I do not know of any instrument that will fulfill these requirements, except the one here described. Where the depression- or elevation-angle of the distant object, whose bearing is required, exceeds 50 or 60 degrees, it becomes difficult or impossible with a prismatic compass, for instance, to obtain accurate results; and since it frequently happens, particularly in mining, that much work requires to be done beyond that limit, it is obvious that an instrument which can be used to observe a high angle just as easily as a low one, if not absolutely a necessity, will at least be a great convenience. How this " pocket transit " attains to the required degree of universality will be understood from the diagram, Fig. 1, in which B is a beveled, graduated circle, attached to and freely revolving about the center of the magnet A. Light falling on B is reflected through a window in F (the compass-box), along the line AC, and is again reflected back to the eye at D by the prism C. By a simple arrangement, the sight-line DCE can be completely revolved in the vertical plane DE, which is normal to AC. It is clear, then, that no matter through what vertical

Jul 1, 1907

By A Karrech, E Hamdi

The uncertainty of geomaterials properties is commonly encountered in resource engineering applications, especially in mining engineering where the rock mass texture, joints, fractures and damage zones can impose the mining method and operation cycles. In the present research work, we focus on the elastic properties of rock masses. We use stochastic numerical simulation of fractured rock masses to estimate their Young moduli. The procedure starts with field mapping campaigns which are conducted to evaluate the locations, dip angles, strike and trace lengths of pre-existing fractures. We develop statistical law parameters of the natural fracture network to represent the weakness patterns. In addition, we use HLA-Dissim, a recently developed and validated Matlab program, to simulate the propagation of monochromatic longitudinal waves and derive the equivalent elastic modulus of fractured rock masses. Such procedure applies within a simulation domain, which is greater than an Elementary Representative Volume.At a second stage, we conduct finite element simulations to validate the previous approach. The matrix and the actual fractures zones are reproduced in the model to mimic the natural set-up. The block is excited on particular positions and its response is evaluated on predefined spots. Real field rock fracture mapping data and monitored single-hole blast induced vibrations are used to validate the theoretical and numerical approaches discussed herein. Comparison between the simulated and measured vibration records shows a great agreement which confirms that the proposed methodology has a full potential to predict and optimise multihole/multidelay blast-induced vibrations.CITATION:Hamdi, E and Karrech, A, 2015. A methodology for rock mass characterisation to control blast-induced vibrations, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 89–96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Ifeanyichukwu Nweke

"Aluminium rolling processing from ingots to cold rolled coils comes with a lot of challenges especially in controlling defective products in casting, hot mill and cold mill operations. Hence this study focused on reducing defects at mills and cast-house using six sigma approaches. The use of six sigma approach will help the production experts to determine the gap between its operation and world class process. Practical data from First Aluminium Rolling mills were presented and analysed and mini improvement projects were proposed based on organisation need to achieve excellence. This study encourages aluminium alloy industries to pursue process improvement projects on the basis of analysis on data obtained from their shop floor, hence ensuring that through this, recovery is improved and cost of poor quality is reduced.INTRODUCTION Engineer Bill Smith while working at Motorola in 1986 introduced a new concept in which a set of techniques and tools are used for process improvement by controlling variations (defects). These tools and techniques are explained by an acronym DMAIC. D DEFINE the problem M MEASURE the variables in the problem A ANALYSE the variables of the problem I IMPLEMENT and verify the solution to the problem C CONTROL the solution to sustain it Most times in six-sigma approach, variations in the process that results in defects and customers’ dissatisfaction are targeted at 3.4 defects per million opportunities. There are numerous methods six sigma application use to achieve quality results and innovative strategies. Improving the quality of process through these methods helps identify and reduce variations which paves way for organisational excellence. In this study, it is encouraged to use six sigma techniques to improve aluminium rolling operations and other aluminium processing activities, the benefits of such improvement concept include: • Satisfy the voice of the customer (VOC) • Minimise costs • Maximise Profits • Build Good Team • Implement Profitable Project"

Jan 1, 2018

By Lluis F. Fontboté

The paper point out the deposits about the carbonate-hosted San Gregorio Colquijirca, as products of an epithermal high sulfidation system. Field, geochemical, and geochronological evidences suggest that the different ore types of the Colquijirca District are caused by a pulsed high sulfidation system subsequent to the emplacement of a diatreme volcanic complex. The first stage formed disseminated Au±Ag mineralization in areas affected by vuggy quartz alteration at Marcapunta. During a second stage, base metal mineralization replaced Eocene carbonate sediments from the Marcapunta diatreme to 2.5 km more to the north. San Gregorio and Colquijirca are to our knowledge the first "carbonate-hosted epithermal Zn-Pb high sulfidation deposit" recognized as such. The correct recognition of this ore type opens new exploration possibilities for base metal in high sulfidation systems affecting carbonate rocks.

Apr 24, 2001

Council for 2004/2005 President F.M.G. Egerton President-elect W.H. van Niekerk Vice-presidents Senior R.P.H. Willis Junior R.G.B. Pickering Immediate Past-president T.R. Stacey Honorary Treasurer J.A. Cruise

Jan 1, 2005