Search Documents

By Darrell L. Beddard

Pile driving started October 29, 1993 and was completed on January 27, 1994. Field work included driving piling from ground surface at one site and at or near proposed footing elevations for the remainder. Piles were driven to specified tip elevations or the elevations directed by the Project Manager. In an attempt to address what installation technique(s) performed the best, several methods were used, including varied predrilled depths, open ended piles, closed ended piles, and the use of both impact and vibratory hammers. Piles were driven closed ended where possible to study the feasibility of this option to reduce construction costs associated with pile cleanout. Piles were driven to different depths to measure capacity variations. The 24-inch (610 mm) diameter piling were driven in one piece while the 42-inch (1.07 m) diameter piling was driven in two segments. A total of 79 piles were driven for the four sites, 74 of the 24-inch (610 mm) diameter and 5 of the 42-inch (1.07 m) diameter. Various hammers were used to determine which hammers provided viable solutions to the potential problems anticipated in the design phase. Hammer selection was based on the driveability studies. Equipment included a 175 ton (1.56 MN) crane, support crane for pile stabilization, crane mounted auger drill, offshore leads, Delmag D30-32, D46-32, and D62-22 diesel hammers, an HPSI 2005 single acting hydraulic hammer, a Foster IHC S-90 double acting hydraulic hammer and a Kencho VM2-25000AII vibratory hammer with the weights set to produce 17,500 pound-inch (1.98 kN-m) of eccentric moment.

Jan 1, 1996

By Jim Wickens, Andy Cole, John Pekrul

"The roaster facility at Barrick Goldstrike Mine treats double-refractory sulfidic/carbonaceous gold ore. Prior to oxidation in the roasters, the ore is ground in two parallel dry grinding circuits utilizing 19’ Ø x 75’ double rotator mills. The design plant throughput was 12,000 dstpd. However, process improvements have significantly increased throughput rates by 25-50%. The current daily throughput record is 20,078 dstpd. Grinding circuit improvements contributing to this success include feed size reduction, ball size optimization, automatic ball charging optimization, and operating strategy changes. In addition to the changes already made, this paper discusses future optimization initiatives including on-stream particle size analysis and “real-time” ore hardness determination techniques.INTRODUCTIONBarrick Goldstrike Mines is located 29 miles Northeast of Carlin, Nevada, USA. Through 2001, the property has produced over 23 million ounces of gold making it one of the premier gold operations in the world.Prior to Barrick’s ownership, the property began producing gold from a small heap leach operation in 1975. The small-scale heap leach production continued through 1986, and in January 1987, Barrick acquired the property. Increased exploration activity by Barrick significantly increased gold reserves. In August 1988, a 4,500 dstpd mill facility was commissioned to treat high grade oxide ore. Also, heap leach operations had significantly expanded. In 1990, the mill was expanded to 6,000 dstpd, and the first autoclave was commissioned to treat refractory sulfide ore. By the end of 1996, the mill and pressure oxidation facility had expanded to 16,000 dstpd and heap leaching had ceased as oxide reserves were exhausted. In 2000, a roaster facility was commissioned to treat double-refractory sulfidic/carbonaceous ore."

Jan 1, 2003

By D. Ingram

"PRIMARY DUST COLLECTOR A. 42,000 CFM James Howden Fan Z-6 Size 3650 Fan Dia 40"" HP 75It was found that the fan was not large enough to remove the air that was displaced by the trucks dumping. So it was removed and an enclosure was installed to isolate the gyro from the rest of the building.B. FANSJames Howden Fans Model RPM 3500 Series 357 FW HP 10These fans were installed when the first dust system was put into operation. It was found that the high RPM and extreme fan wear caused a major maintenance problem. These fans were replaced with Chicage Blowers Model SWS1 RPM 1180 Dia 36"".DRY CYCLONE COLLECTORS A.,Three four foot rubber lined cyclones. Four six foot rubber lined cyclones.All under flow. Water is controlled manually and gravity flows to a central sump box. From there it flows to the grinding circuit in the Mill.Cyclone under flow product runs between 100 and 200 tons of dust per 24 hours with a screen analysis 30% + 400.The cyclone under flow product is diluted to about 3 to 4%. Solids total gallonage approximately 400.B.,Elbair Wet Scrubber125 HP RPM 56042,000 CFM,Model PX861The Elbair collects the total product from the discharge. Of the Cyclone fans the under flaw goes to the Mill - the Elbair discharges stack goes to atmosphere.The Elbair wet scrubber had to be redesigned in order to keep it in service."

Jan 1, 1976

By H. Ahrens

El presente estudio refiere la importancia de los explosivos y detonaciones en el campo de la minería a través de una breve revisión historiográfica, legislación, problemas relacionados con la voladura y métodos empleados. Cabe sa señalar que la evaluación de estos explosivos, así como las pruebas características de estos conllevan una aplicación práctica, de forma que se pueda conocer la composición del explosivo y determinar una posible falla en los disparos.

Nov 20, 1972

By Joshua Micah Hoffman, Jhon Silva-Castro, Kylie Larson-Robl

A coal mine impoundment failure has the potential to be environmentally devastating and life-threatening. It is well documented that after seismic events slope failures in impoundments can occur. It has been concluded that often the main driven factor of the failure is the increase in excess pore pressure due to ground vibration. A small amount of research has been done regarding the stability of coal mine impoundments under natural seismic events; however no research has been done considering vibrations from mine blasts. If it is taken into account that current environmental restrictions oblige to increase the capacity of coal mine impoundments, thus increasing the hazard of such structures, it is necessary to evaluate the effects of near-by mine blasting on the stability of the coal mine impoundments in order to mitigate and control the potential of slope failures. To study the behavior of excess pore pressure under blasting conditions, scaled simulations of production blasting events were set up inside of a controlled sand tank. The research was divided in two stages. The first one was done, using dry conditions, while in the second part, the same set of tests were performed under saturated conditions. This document shows the partial results for stage one (dry conditions). For the tests, explosive charges were set off within the sand tank at various distances to simulate different blasting distances. Information was collected from geophones, accelerometers, microphones and high speed video camera for dry and saturated scenarios and additionally from piezometers under saturated conditions to assess the behavior of the material under blasting conditions.

Jan 1, 2015

The concentrated efforts now being directed towards the development and application of monitoring and control techniques have now resulted in their widespread use in UK mines together with evidence of benefits resulting from their application. There is little doubt that the longwall method of producing deep mined coal will continue but will be made more reliable and efficient with the aid of control technology. The major fields of research and development work are concerned with planning and design of mines and mining equipment; management and engineering information; and automation of coalface, tunnelling and transport systems. The principal achievements now in widespread use are: the standard computer system MINOS, widely applied to mine transport, coalfaces and mine environment; extensive use of machine condition monitoring leading to condition-based maintenance; underground automation of conveyor systems and guidance systems for ranging drum shearers and boom-type roadheaders are being widely introduced.

Jan 1, 1985

By C. Baldwin Sawyer

J. S. Vanick,* Washington, D. C. (written discussion).—To those who have been confronted with the study of the gas-metal reactions, this paper is a most welcome contribution. My personal interest in work bearing upon this general problem, stimulated by an appreciation of the difficulties inherent to problems of this type, prompts a few words of discussion. Table 2 of the paper shows a gradual increase in the nitrogen content with an increase in pressure, and an interpretation follows in which nitrogcn is used as the compressed medium when the conditions admit that cyanogen gas could be active as a contaminating ingredient. Fusions of electrolytic iron made in the induction furnace in an atmosphere of deoxidized nitrogen and out of contact with contaminating materials have shown no microscopic evidence of -a nitrogen increase; using a refractory-lined graphite crucible in the furnace under the same conditions or admitting air often resulted in the occurrence of nitride needles in the solidified melt. These results suggested that a nitrogenous compound served as a vehicle for the introduction of nitrogen and that such compound was not available when the pure gas and carbon-free refractory were used. The fusion of pure iron in pure nitrogen is perhaps a matter of theoretical interest. The author's work serves a more practical purpose when applied to steels rather than iron. Table 2 reports the absence of nitride needles in melts made under pressure of one atmosphere, although the quantity of nitrogen present would seem to exceed microscopically detectable percentages. In some recent work29 on carburized iron, nitride needles have been observed in areas analyzing as low as 0.015 per cent. nitrogen. This low percentage of nitrogen would indicate that the solubility limit is less than 0.030 per cent. for hypoeutectoid steels. There is the possibility that the areas of pearlite which exist in a hypoeutectoid steel restrict the distribution of nitrogen and limit its presence to the ferritie fields. In view of this work and the references quoted by the author, I am led to expect that the value for the solubility of nitrogen in solidified iron may approach

Jan 1, 1924

By V. Bari?ic

The scheduled power cuts of early 2008 were a disturbing reminder that South Africa needs to expand its power-generating capacity. Low-grade and discard coals, of which South Africa has much, are a source of energy and amenable to combustion in circulating fluidized beds (CFBs). Foster Wheeler (FW) has a long record in developing this technology in boilers. The technology is flexible in burning a variety of fuels; low-grade, high-ash coals, good quality bituminous and anthracite coals, and biomass and waste fuels have all been used. CFB boilers are efficient, reliable and can be designed to meet tight emission standards. In recent years once-through supercritical (OTSC) CFB technology has been developed. It enables the next stage in CFB development to proceed to a medium-scale (500 MWe) utility in such projects as Lagisza, which runs at a net efficiency of nearly 44%. Scaling the technology up to 800 MWe with a net efficiency of>45% is planned to be commercial during 2009. CFB technology can reduce CO2 emissions in the repowering of coal-fired and greenfield power plants. It does so through greater efficiencies and by co-combusting coal with biomass. FW has also developed CFB technology for the gasification of biomass, as, for example, in a pressurized gasifier to produce syngas, which can be used for the production of biodiesel, thereby reducing CO2 emissions from vehicles. Carbon capture and storage (CCS) can potentially cut CO2 emissions in the generation of power from fossil fuels in the short term, provided that it gains public acceptance, that the required regulatory framework is created, and that emission-trading mechanisms or other incentives provide a solid return on the major investments required. Oxyfuel combustion is an option in CCS; Foster Wheeler is adapting its CFB combustion technology for oxy-fuel combustion to meet this challenge. It is developing Flexi-burn?, which enables a plant to be operated either with or without carbon capture. This paper describes the status of CFB technology in terms of boiler efficiency and fuel flexibility. It highlights the advantages of CFB technology for oxyfuel combustion, presents a development plan for Flexi-burn?, and discusses a pressurized gasifier for biodiesel applications.

Jan 1, 2009

By M. F. Trice

PYROPHYLLITE is a hydrous aluminum silicate (A12Si4010(OH)2)1 that occurs in both the foliated and the massive forms. The foliated variety resembles talc in that it has a greasy feel, a pearly luster, perfect basal cleavage, and usually is white, although in some deposits apple green, gray, brown, russet, and nearly black specimens may be found. The massive deposits of pyrophyllite yield pearl gray to light tan aggregates, some of which are so friable that they may be crushed with the hands into a fine gritty powder. Frequently specimens of the massive variety are studded with crystals of radial structure. The mineral has a specific gravity of about 2.7 and a hardness of 1 on Mobs' scale.1 The chemical composition of commercial pyrophyllite reflects the mineralogy of the deposits, which, according to Stuckey,2 contain pyro-phyllite and quartz, together with chloritoid, sericite, and a few other minerals of negligible importance. The latter, he says, "are noticed in but small quantities to the extent they might occur as accessory constitu-ents of an igneous rock or as products of regional metamorphism or weathering. . . . Quartz is abundant everywhere except in the very best grades of pyrophyllite." Analyses of specimens from several deposits are listed in Table 1, showing that the silica content varies from 57 to 73 percent and the alumina from 22 to 33 percent. Oxides of iron and the alkaline metals are collectively present, with one exception, to an extent of about 1 to 1.5 per cent.

Jan 1, 1940

By S. R. Titley

Carbonate-hosted massive sulfide (60%) ores of the western Cordillera compose a distinct class of deposits although they vary widely in detail and perhaps genesis. They have been important sources of lead, zinc, copper, silver, gold, and more rarely, molybdenum, tin, and tungsten in complex mineral assemblages usually dominated by pyrite. They occur as concordant stratiform bodies, as discordant mantos, and as chimneys crossing tens of meters of section; many are associated with faults and breccia bodies. Environments of formation of carbonate hosts range from craton basin to shelf with ages from Proterozoic to Cretaceous; in many instances, dating has shown mineralization to be significantly younger than hosts. Temperatures of formation determined for many deposits are high (200°-400°) and many districts are centers of igneous activity manifested by dikes, sills, and stocks. However, direct cause and effect relationships have been difficult to establish. Many important problems attend the renewed interest and study of these deposits and include questions of metal-sulfur sources, metallization processes and histories, geological controls at all scales, and relationships to broader patterns of metallogeny.

Jan 1, 1985

By Matthew Janes

Quality control procedures are increasingly important with today's higher capacity foundations and complex loading conditions. The need for a mobile, repeatable, nondestructive and economical load test method led to the development of an entirely new approach. The system described involves using solid propellant fuels to accelerate a reaction mass off the test pile. The force required to accelerate the reaction mass upward acts equally downward on the pile. Very high forces may be applied to the pile in a controlled, linearly increasing manner. The duration of the applied load is approximately 100 milliseconds. This rate of loading is slow enough to allow the pile and soil to react together as a composite rigid body. Pile/soil accelerations and velocities are low, typically 1 g and 1 m/s respectively. The effects combine to produce pile and soil response no longer dominated by the transfer of force via stress pulse (as with impact). Instead the pile force increases throughout the length of the pile, with pile top and toe stresses building in unison with time. This emulates the stress condition during static pile loading. Finally, state of the art instrumentation systems are used to obtain test data. Displacement is monitored directly using a laser datum and integrated receiver located at the centre axis of the pile. Force is also monitored directly using a calibrated load cell. Data is acquired and digitized using a 386 PC with user friendly software capable of producing load deflection curves and time histories in the field seconds after testing.

Jan 1, 1990

By M. Jele

? Sulphuric acid plant in umbogintwini. ? Double absorption plant, capacity of 550MTPD. ? Build by simon curve during the year 1973. ? Side stream plants such as: ? Liquid SO2 Plant, ? Liquid SO3 and ? Oleum plant

Jan 1, 2009

By D. Seneviratne

Iron transfer from the pregnant leach solution (PLS) to the electrolyte can have a major economic impact on solvent extraction (SX) operations. High iron transfer will lead to greater operational costs, due to increased reagent consumption through electrolyte bleed and make up, or increased power costs due to decreased electrowinning current efficiency. Bioleaching of low-grade copper sulfide ore from the Kennecott Utah Copper Mine was investigated in a large scale piloting program including SX and electrowinning. Plant data and lab test work conducted throughout the course of operation, show that the unique containing PLS high ferric iron with high pH can lead to lower Cu: Fe selectivity than is typically seen in traditional copper SX operations. The impact of high ferric iron on the plant operation, and methods to reduce iron transfer will be discussed. Special considerations need to be taken for plant operating conditions and selection of SX reagents (including both extractant and aromatic content of diluent) based on the feed PLS characteristics.

Feb 23, 2014

By Louis H. Meece

The romance of the River lives on in the tales of Mark Twain; and many Americans still think of the Mississippi River in terms of the steamboats loaded with passengers, gamblers and cotton. Yet for many years, coal has been a major cargo on the American waterways. Currently, about 100 million tons a year of coal is handled in some part of its journey from mine to destination by barge. The bulk of this traffic has been on the Ohio River System and the Upper Mississippi River System in years past. Now we have a new entry. Over the past 10 years various movements of coal have developed down the Mississippi River to power plants at Memphis and along the Gulf Coast, and a small amount of metallurgical coal has moved down the Mississippi River for export to Japan since 1970. But in 1980 a brand new player came on the scene. 1980 was a momentous year for the American coal business. Historically, we have exported about 50 million tons a year of metallurgical coal to the world's steel mills. Just before and after World War I, we also had a fairly healthy export trade in steam coal; and again in the late forties, we supplied large amounts of coal to Europe until domestic production could recover from the ravages of World War II. But since the early fifties, the name of the export game has been metallurgical coal. Starting in the mid seventies, something began that was almost totally missed by the American coal industry; and that was the growth in the use of coal first in Europe and now in the Far East as a steam product and as an alternative to petroleum products. As these world coal markets began increasing, the U.S. at first was thought to be noncompetitive because ocean rates were still very low. For example, as recently as 1977, Australian coal could be moved all the way from Australia to the Gulf Coast for $12.50 per metric ton. Coal exporting countries were Poland, Australia and South Africa, except for the continuing exports of U.S. high quality metallurgical coal. But then came the second oil shock, and all of the sudden that $12.50 rate from Australia to the U.S. Gulf became $25.00. And then suddenly and almost unrecognized by the American industry, American coal was in fact competitive at overseas destinations because of the drastic change in trade patterns brought on by the doubling and tripling and quadrupling of bunker fuel prices for ships.

Jan 1, 1982

By Ruy L. Rodrigues

Vale is in the early stages of commissioning its Onça Puma nickel operations. The project is meant for the production of 58,000 tpa of nickel contained in ferro-nickel, substantially contributing to the company?s vision to achieve world leadership in the nickel business. Mineral resources will be exploited from the homonymous deposits in the Midwest of state of Para, Brazil ? some 100 km southwestwards from the company?s Carajás iron ore properties. Resources as of 83 Mt at 1.73 % Ni will sustain a mine life of approximately 40 years. The property was acquired in late 2005 and Vale has since extended the engineering studies and proceeded with the implementation. Nickel will be mined from saprolitic ore at a rate of approximately 10 Mtpa (ore plus waste) in early years ? ramping up to some 15 Mtpa 7 years later ?, to feed the plant at a rate of 2.5 Mtpa. The process uses conventional RKEF (Rotary Kiln Electric Furnace) pyrometalurgical route whereby the ore is homogenized, calcined in rotary kilns, melted in electric furnaces and further refined to ferro-nickel. The plant has been designed and constructed applying the latest available technology, aligned with Vale?s vison to exceed the highest existing standards for environmental control, health and safety and productivity in the industry. Total investments in these operations are anticipated to correspond to USD 2.3 Bi and will materially contribute to the regional development and well being of the nearby communities and other stakeholders.

May 1, 2010

By H Chen

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Mesozoic iron oxide-copper-gold (IOCG) mineralisation in southern Perú and the northern Chile coastal IOCG belt have emerged as two of the major exploration targets in the Central Andes in the last two decades. These Mesozoic Andean IOCG deposits formed in two mineralisation epochs, the Middle-Late Jurassic (170–150 Ma) and Early Cretaceous (130–110 Ma), with the major Cu-rich IOCG deposits located in the Early Cretaceous mineralisation belt. The early studies in some IOCG centres support a magmtic-hydrothermal model for both Cu-rich IOCG deposits and broadly contemporaneous Cu-poor ‘Kiruna-type’ magnetite deposits. However, recent evidence from field, geochronology, fluid inclusions and stable isotopes show that in the major Central Andean deposits (eg Raúl-Condestable, Mina Justa in southern Perú, La Candelaria-Punta del Cobre and Mantoverde in northern Chile), the incursion of evaporite-sourced basinal brines or sea water may be a prerequisite for economic Cu mineralisation. Moreover, the Cu-poor massive magnetite deposits could be interpreted as a product from iron oxide melt, with minimal intervention by non-magmatic fluids. Therefore, they could represent two contrasted deposit types and contain little genetic relationships. The different roles of magmatism during the Mesozoic are responsible for the variable mineralisation in the Central Andes, including IOCG, magnetite and ‘manto-type’ deposits. The ore modelling for both the Middle-Late Jurassic and Early Cretaceous metallogenic epochs in the Central Andes are reconstructed.CITATION:Chen, H, 2015. The Mesozoic iron oxide-copper-gold (IOCG) mineralisation in the Central Andes – a refined IOCG ore-forming model in the Palaeozoic Continental Margin, in Proceedings PACRIM 2015 Congress, pp 251–254 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By W. K. Connor, O&apos

The Bureau of Mines has conducted beneficiation, carbothermic reduction, and leaching tests of Mn oxide ores as part of its evaluation of the Mn and Co resources of the West- Central Arkansas District. The major Mn oxides in the ore include cryptomelane, psilomelane, pyrolusite, and lithiophorite. Cobalt is contained within the Mn oxides. Nonbeneficiated ore was reduced at 800' C with coal and leached in ammonium sulfate and ammonium carbonate leach liquors. Ore concentrates were calcined at 600" C prior to reduction under the same conditions as the raw ore. Head analyses reported up to 21 ptt Mn and 0.11 pct Co. Extractions of 70 to 90 pct Mn and 40 to 60 pct Co were achieved.

Jan 1, 1992

By R. L. Castro

Block caving methods, when operated under favourable rock mass conditions, can achieve higher production rates and lower operating costs than other various existing underground mining applications. For this reason, it has been considered the preferred method for the mining of deep and large orebodies in current and future operations around the world. One of the key aspects in the design of block caves is the selection of the production level layout, which, among other parameters, is based on the gravity flow characteristics of the caved rock. This is because gravity flow has a large impact on total ore recovery and the amount of dilution in a caving operation. Today, there are a number of computer based methods which aim to emulate the gravity flow pattern of the caved rock. In this paper, the authors present the development of FlowSiman improved model of gravity flow based on the cellular automaton approach, to estimate dilution entry, mixing and ore recovery. As part of the model development, flow simulations were conducted and subsequently compared to full-scale data collected at two mine sectors operated by Codelco Chile. The results indicate that by using proper calibrated parameters, good correlations between simulated and measured grades as well as dilution entry are obtained. The potential use of the numerical tool to evaluate drawpoint spacing in terms of recovery and dilution for block/panel caving operations is also presented.

Jan 1, 2009

By Carl Hendricks, Malcolm Scoble

There currently exists no viable means of obtaining continuous, quantified feedback on blast efficiency. This paper describes the adaptation of a loading shovel to serve as a diagnostic tool in evaluating the success of ground preparation practices. Work undertaken in a large western Canadian open pit involved microprocessor-based instrumentation for the performance monitoring of an electric mining shovel. The monitored shovel responses proved to be reliable indicators of variations in muckpile d&ability. This approach is considered to provide a very comprehensive survey of post blast conditions since the shovel must physically interact which every cubic yard of blast fragmentation.

Jan 1, 1991

By Benjamin H. Clark

"For over 50 years, Derrick Corporation has been renowned for its innovative and durable fine screening equipment and screen surface technology. Derrick’s latest innovation, the patented Stack Sizer, offers mineral processors both high tonnage capacity and high separation efficiency on an extremely small footprint.The Stack Sizer is suitable for separations from 6.3 mm down to 75 microns (200 mesh). The Stack Sizer, coupled with Derrick’s patented urethane screen surface technology, offers an extremely economical alternative to hydraulic classifiers, hydrocyclones, and less efficient low volume wet screening systems. Stack Sizers have been used in feed preparation for flotation, spirals, and a variety of jigs. Mineral processors wishing to reduce grinding circuit circulating loads and generation of slimes due to over grinding, thereby enhancing the efficiency of flotation and gravity circuits, now have another technology at their disposal to perform this critical sizing and grade control function.Over 200 Stack Sizers have been installed in numerous mineral processing applications worldwide attesting to the rapid acceptance of this technology. Stack Sizers are currently screening ferrous and non-ferrous metal ores, mineral sands, silica sand, kaolin clay, feldspar, garnet, phosphate, aluminum dross, potash, coal, tantalum, spodumene, niobium, and other rare earth mineral ores.INTRODUCTIONDerrick engineers have long understood and demonstrated the importance of screen width in coupling both high capacity and high separation efficiency for fine wet sizing applications. As opposed to fine dry sizing, where the length of the screening machine is critical for high separation efficiency, introducing slurry feed to screens in a thin and even layer at minimal velocities across wider screen surfaces allows for high capacities and efficiencies, with maximum screen cloth life. This is due primarily to the combination of free liquid and high frequency vibration of the Derrick motors, which allow fine undersize material to pass through the screen apertures. Lacking either of these factors would be extremely detrimental to the screening process. Without the high frequency vibration of the motor, the screen is essentially a low efficiency sieve bend. Without the free liquid to carry fines through the screen openings, the screen is for all intents and purposes a glorified conveyor or dewatering unit, as little or no sizing takes place once the screen is devoid of free liquid. For optimal screening results, Derrick recommends feeding slurry to a screen at approximately 20% solids by volume. Figure 1 shows the Stack Sizer design concept. Note that a single feed point is used to evenly distribute the flow to the five separate feed points."

Jan 1, 2007