Search Documents

By G. M. Castillo

Newmont?s Phoenix mine started production in March of 2006. Due to the extreme hardness of the ore, the mill has struggled to meet throughput projections. Grinding studies showed that optimizing the existing circuit would not achieve budgeted throughput. These studies also showed that the pebble crusher was being underutilized due to the inability of the SAG mill to break the rock. The concept was developed to supplement the feed to the existing pebble crusher with a secondary crusher. Models of this process looked favorable so a portable crusher was installed to test the process. The temporary crusher was successful at increasing the throughput by 7% and based on the operating data, plans are currently being developed to install a permanent secondary crushing system in front of the SAG mill. This paper will review the results from the test crusher and the flow sheet for the permanent secondary crusher.

Jan 1, 2012

By Cherie H. Tilley

The possibility of drilling oil wells from underground locations is not a new concept. It bas not been cost effective for the oil industry in the past and therefore disregarded. Today's state of the art in tunneling and shaft sinking greatly improves the potential for this type of oil field development scheme. This report presents a plan for providing a aeries of drilling bases and the design of the drilling location. The design minimizes the amount of excavation needed to develop the oil field and maximizes the use of rapid excavation techniques.

Jan 1, 1983

By A. G. Scobie

THE research laboratory of this Company was recently faced with the problem of determining trace amounts of tungsten in a series of classifier sands. A spectrographie survey revealed the feasibility of using this instrument in the final evaluation, but a check of the common methods in use for the isolation of tungsten (3, 4) showed these methods to give incomplete separation for trace amounts. An investigation into the possibility of modifying these procedures, or developing others, was thus indicated. ASSAY PROCEDURE Weigh 10 grams of 200-mesh ore or concentrate into a 400-ml. beaker, wet the sample well with about 20 ml. of water, and add 100 ml. of hydrochloric acid. Cover, digest at 60° to 70° C. for about 1 hour, and then boil down to approximately 25 ml. Cool, add 25 ml. of hydrochloric acid and 10 ml. of nitric acid, and again boil to former volume. Add 20-ml. portions of nitric acid with successive boiling clown until chemical action is complete. Then add 20-ml. portions of hydrochloric acid until all nitric acid is removed. Take nearly to dryness on a law-temperature hot plate, but do not bake. Take up in 10 ml. of hydrochloric acid and 20 ml. of water and heat on a law-temperature hot plate until all iron goes into solution. Dilute to 200 ml. and heat to just below boiling. Stir in pulp of about half of a No. 41 Whatman filter paper (12.5-cm.) and continue digestion on plate with occasional stirring for 15 to 20 minutes.

Jan 1, 1943

Cadmium occurs in the Broken Hill Lode essentially as a camouflaged element, substituting diadochically for zinc in the sphalerite.Analyses of a series of zinc concentrate flotation products, prepared from samples of ore taken at intervals throughout the developed lengths of the several orebodies forming the lode, have revealed a pattern in the distribution of cadmium relative to zinc. This pattern appears to reflect the temperature and order of deposition of the several orebodies, and the direction of movement of the mineralizing solutions.INTRODUCTIONThis investigation into the distribution of cadmium in the several orebodies of the Broken Hill lode was undertaken by the Mineragraphic Section. of C.S.I.R.O. in conjunction with the Broken Hill Geological Research Committee, as part of a study of Broken Hill mineralization.It arose from the examination of cadmium and zinc assays supplied by Mr. T. A. Read, Chief Metallurgist of the Broken Hill South Ltd.; of experimental zinc concentrates prepared from localized samples of the No, 2 and No. 3 orebodies in the Broken Hill South Mine. These assays suggested that the two orebodies were characterized by distinctive ZnjCd ratios.In view of the possible sigmficanc'e of such a difference, comparable data were sought from each of the other mines. The necessary samples of ore were collected by the geological staffs of the several mines. The preparation of separate zinc concentrates and lead concentrates from these samples, and their assaying, was conducted by Mr. Evan Hardy, for the North Broken Hill Mine, and its assodated leases, and by Mr. D., Swan, under the direction of Dr. J. C. Nixon, for the Zinc Corporation and New Broken Hill Consolidated Mines. Additional tests on the Broken Hill South Mine were made by Mr. C. W. Reilly, under the direction of Mr. T. A. Read. The samples were...

Jan 1, 1955

By Robert L. Thorne

As an integral part of the investigation of critical and essential minerals in Alaska , the Bureau of Mines examined the lead deposits in the Slana area . Four examinations were made during June , July, and August 1945 in the 200 - square -mile area immediately northwest of Slana . The settlement of Slana lies near the conflux of the small Slana River with the mighty Copper River less than 60 miles southwest of Tek Junction on the Alaska Highway . Travel through the area and the examination of the properties were conducted by a three-man crew consisting of the author , a caterpillar operator , and a laborer . An RD6 caterpillar , equipped with blade and winch , was used in breaking trail and freighting through the country . Supplies and equipment were loaded on a 7- by 14 -foot , double - end , go -devil , which was hauled by the tractor .

Nov 1, 1946

By H. F. JR. Miller

(Butte Meeting, August, 1913.) THE major cause of the deterioration of the open-hearth furnace as its length of service increases, is the melting down, or rather the slagging, of the checker-brick, together with the deposition of dirt in the form of iron oxide, etc., which helps to close the openings, as well as to slag the brick by chemical action. Any construction that will do away with the necessity of having the waste gases come down through the checkers will eliminate the main reason for their deterioration. There are some other well-defined reasons which are subordinate to the main one given above. Some of the defects of the present type of regenerator chambers are as follows: 1. The checkers cannot be cleaned while the furnace is in operation, nor can they be cleaned at the end of the run without taking out all of the checker-brick. This causes high costs for labor and brick. The labor cost is high because all checker-brick have to be handled twice. The brick cost is high because many of the bricks are spalled in the double handling, rendering them useless because a spalled brick will not stand up. 2. The top courses of brick become coated with iron oxide, etc., melt clown, and large amounts of dirt are deposited throughout the checkers, especially at the bottom. The draft of the furnace is decreased by the closing of the top and bottom openings, especially the top ones, and the entire working of the furnace is affected. If an effort is made to clean the checkers the dirt and brick falling down into the holes still further diminish the draft. 3. The distribution of the air or waste gases through the checkers is in many cases uneven, resulting in a lower temperature of pre-heated air and therefore a slower working furnace. Also, the passage of air and waste gases is so crooked that sometimes the chimney is not powerful enough to overcome the friction.

Jan 6, 1913

By B. B. Broms

Embankment piles are common in the Scandinavian countries (Kjellman, 1940) and in Southeast Asia as support of fills, light structures, bridge abutments and deep excavations (Eide, 1968) as described in the following. Untreated timber piles are often used for light structures and shallow fills when the ground water level is high since they are inexpensive and readily available. When the applied loads are relatively high precast concrete piles and steel piles are preferred. DESIGN CONSIDERATIONS Embankment piles carry the load from a fill or a struc-ture either through skin friction along the sides of the piles (Fig. 1a) or through a precast concrete slab or through pile caps at the top of the piles (Fig. 1b). When the load is carried by skin friction it is often economical to use small diameter timber piles because of the large surface area (Asplund, 1939). For precast concrete or steel piles concrete caps are used to transfer the load to the piles due to the relatively high capacity of the piles since the skin friction resistance alone is not sufficient to transfer the load to the piles.

Jan 1, 2010

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members) The following is a partial list of members and guests who called at Institute headquarters during the period Mar. 10, 1917, to Apr. 10, 1917. George S. Blair, Pittsburgh, Pa. E. P. Mathewson, Toronto, Canada. H. M. Boylston, Cambridge, Mass. T. Poole Maynard, Atlanta, Ga. F. J. Brule, Toronto, Canada. . W. J. Mead, Madison, Wis. M. B. Cohen, Miami, Ariz.. D. G. Miller, Denver, Colo. W. M. Corse, Buffalo, N. Y. P. N. Moore, St. Louis, Mo. F. G. Cottrell, Washington, D. C. R. H. Morris, Ansted, W. Va. E. C. Cross, Cleveland, 0. W. J. Morrison, Toronto, Canada. Nelson Dickerman, San Francisco, Cal. M. F. Ortin, Petrograd, Russia. F. N. Flynn, Chuquicamata, Chile. G. W. Paymal, New York, N. Y. F. L. Garrison, Philadelphia, Pa. Edward H. Perry, Boston, Mass. J. S. Grasty, Charlottesville, Va. 0. G. Petersen, Somerset, Ky. H. D. Hibbard, Plainfield, N. J. H. C. Price, Bartlesville, Okla. H. L. Hollis, Chicago, 111. C. A. Richardson, Toronto, Canada. F. H. Jackson, Marysvale, Utah. Hallet R. Robbins, Vancouver, B. C., Can. W. Strickler Jones, Silver City, N. M. A. H. Rogers, Boston, Mass. E. B. Kirby, St. Louis, Mo. H. G. Smith, Princepulca, Nic. J. M. Lovejoy, Electra, Tex. Edwin G. Steele, Van Horn, Tex. A. F. Lucas, Washington, D. C. 'S. A. Taylor, Pittsburgh, Pa. Edwin Ludlow, Lansford, Pa. A. P. Thompson, Salt Lake City, Utah, E. Francis McCrossin, Birmingham, Ala. Milton A. Allen is now engaged in the New York office of Messrs. Arthur L. Pearse & Co. Percy E. Barbour, managing editor of the Engineering & Mining Journal, has been appointed, by Governor Whitman, Deputy Superintendent of Police of the State of New York.

Jan 6, 1917

By N Yarahmadi

Characterization of pore pressure is critical for appropriate design of tailings dams. Furthermore, if seepage rates through tailing embankments increase unexpectedly or become uncontrolled, undesirable conditions may prevail to progress piping or internal erosion that could lead to the dam’s instability or ultimate failure. A three-dimensional seepage analysis was performed on a tailings dam using finite element method to find the rate of seepage and pore water conditions in the embankment and foundation. The results were then compared to a conventional two-dimensional seepage analysis carried out on the typical cross section of the embankment and the field data acquired from the instrumentation system. Considering the monitoring data, comparison of seepage analyses results for the two and threedimensional models, showed that the results of the conventional two-dimensional seepage analysis are significantly underestimating reality. Relying on two-dimensional seepage analyses might result in underestimation of seepage rates and impact the safe operation of tailings dams. Similarly, unrealistic prediction of pore water pressure conditions, based on simplified seepage analyses, can lead to overestimation of the rate of strength gain of material and consequently safe embankment raising rates.

Jul 1, 2021

Reduce accidents associated with handling of the electrical trailing cable and the water hose on mining equipment. Approach Two reels were mounted on a loading machine to store and release the lines as required during face operations. How It Works A hydraulic motor, which is actuated by a treadle valve in the operator's cab, controls the reel on which 50 feet of electrical power cable is stored. A spring motor resists unwinding of the other reel on which 50 feet of water hose is stored. Both reels are mounted on the right rear of the loading machine. See Figure 1. Following common mining practice, the cable and hose are anchored to fixed points at the first intersection outby the face. Tramming forward causes the cable and hose to be pulled from the reels. Depressing the treadle valve causes the electric cable reel to turn and wind-in any slack in the cable. The spring tension on the water hose reel automatically rewinds the water hose when the loader is trammed in reverse.

Jan 1, 1978

By AIME AIME

AT the annual .meeting of the Minnesota Section in December, Dr. Leith characterized as a question still open the exact method of origin of Lake Superior iron ores and emphasized it as an important practical problem for the future. He welcomed the step taken last year by Dr. Gruner in presenting a new hypothesis, and asked Lake Superior geologists to meet the challenge of such multiple hypotheses by unbiased, study.

Jan 1, 1932

By W. J. Wolfe

"Quartz Hill is a large, low- to moderate-grade quartz vein stockwork porphyry molybdenum deposit, discovered in 1974 during a regional stream sediment geochemical reconnaissance survey of southeast Alaska conducted by United States Borax and Chemical Corporation. Mineralization is localized in the upper parts of an Upper Oligocene (30 Ma) composite quartz monzonite stock which is emplaced discordantly into older Cretaceous to Early Tertiary terrain of the Coast Range igneous metamorphic complex of the northwest North American Cordillera. Subsequent fault-controlled, complex multi-stage intrusion, concentrated in the core of the Quartz Hill stock, produced successive pulses of hydrothermal alteration and molybdenum mineralization at about 27 Ma. Overall, the deposit is tabular and flat-lying and well suited to open pit mining. The 0.05% MoS2 grade limit covers an area of approximately 1500 m by 2750 m and extends to a maximum depth of 520 m below surface. Details of grade distribution show two separate lobes of higher grade material within the larger low-grade deposit.A ten year program of exploration drilling, underground development, sampling and metallurgical testwork led to a 1983 feasibility study based on a resource of 1600 million tonnes grading 0.127% MoS2 at a 0.08% MoS2 cutoff The large size of the deposit and its homogeneous grade distribution, typically showing gradual outward decrease of grade, makes in pit grade selection practical at several cutoff levels. Cominco Ltd. now reports a Probable Resource of 210 million tonnes averaging 0.22% MoS2 with a further Possible Resource of 1100 million tonnes averaging 0.12% MoS:z. At low molybdenum metal prices which have persisted for 10 years since the molybdenum price spike of the late 1970s and early 1980s, the Quartz Hill deposit is sub-economic."

Jan 1, 1995

Study on Beneficiation Technology of a Refractory Fluorite Ore in North China

Sep 13, 2010

By Bohrn W, Milionis K, Tessmer G, Reidetschlager J

The share of electric arc furnace based steel production is increasing - New technologies for the production of virgin raw materials for EAF production are under development and on the market - VAI has a strong position in the field of scrap substitution technologies with their COREX«-, COREX«-DR and FINMET«-technology. In late-1998 the steel plant SALDANHA was started up successfully. This integrated compact mill is using the COREX«-technology as hot metal and a combined DR-plant as DRI production unit. Also in 1999 the BHB FINMET« plant Port Headland went on Stream.

Jan 1, 1999

By John P. Davis

The use of conventional, circulatory air rotary and fluid rotary, cased and uncased drilling methods in the vicinity of sensitive infrastructure can have deleterious effects on the ground conditions surrounding and supporting structures and the structure itself. Furthermore, the use of these conventional methods offers the engineer or contractor little information about the condition of the subsurface during geotechnical applications. Conversely, sonic drilling measurements and samples can be used to evaluate actual conditions during the progress of exploration and construction across a given site. This paper will discuss the history and properties of sonic drilling and explore case histories of geotechnical applications for the advancement of boreholes within vulnerable structures and on sensitive sites for several recent infrastructure projects ? a tunnel and railroad project, a dam grout curtain project, a bridge micropile exploration project and a tunnel instrumentation project. Project summaries will discuss the advantages realized when the application of sonic drilling techniques demonstrated superior accuracy, quality control, efficiency, productivity, penetrability, waste minimization and adaptability when drilling adjacent to or within existing infrastructure. Finally, the discussion will address the current testing and application of sonic drilling to the installation of micropiles, earth retention anchors, grout injection and instrumentation installation where the quality control benefits provided by the inherent soil cores, measurement while drilling systems, accuracy and non-destructive production drilling features will be advantageous.

Jan 1, 2006

The great problem at Port Pirie and many other lead smelters has always been to keep the lead content of the slags down to a low level. This has been done in the past largely by empirical methods, the lead content varying from less than 1 per cent to over 4 per cent, the more usual figure being something under 2 per cent. Subsidiary to this, but of major importance in the future, was the extraction of the considerable quantities of zinc in the slag. At this stage little was known about the constitution of the slags apartfrom their chemical composition. Some early work on slag constitution was carried out in the B.H.A.S. Research Laboratories between 1919 and 1921, but except for a microscopic examination of a few thin sections the greater part of this investigation wasdevoted to the recovery of the zinc content of the slag by leaching methods.In 1949, therefore, it was decided to initiate a programme of fundamental research into the constitution and properties of the lead blast furnace slags. The information thus gained would give a clearer picture of reactions taking place in the slag, both in the blast furnace and during dezincing.There was also the hope that these results would lead to improved industrial techniques resulting in smaller lead losses, and, taking the long-term view, to efficient methods of producing zinc from the slags.A series of investigations was therefore begun at various centres over a period of time. These were:1. A mineralogical examination of the slags by Dr. A. B. Edwards of the Mineragraphic Section, C.S.I.R.O.2. A study of the thermodynamics of various slag com...

Jan 1, 1956

By T. Carl Shelton

The coal industry of the United States in 1967 had reasons to be both exuberant and concerned about its present and future role in the economy of the country. Continuing a momentum that began in the early 1960's, the industry has moved ahead in providing competitive customized products to strengthen its long-term domestic and foreign commitments, and has maintained with steady progress its position as a major supplier of energy. On the other hand, the industry must overcome air- water pollution and conservation-reclamation problems that have been identified by 1967 legislation. Throughout the year, the industry was characterized as "progressive," "healthy" and "dynamic." To have been termed a "growth industry" in 1967, is an accolade the coal industry can accept with pride. Culminating its efforts throughout the decade, the industry has emerged with a competitive image that is representative of its future strength.

Jan 2, 1968

By P Yß±ez, G Ferguson

The El Teniente mine produces more than 340 000 tonnes of fine copper per year from an industrial complex of underground mine, concentrator and smelter. Mass caving methods are employed to deliver approximately 95 000 tpd of ore to the mill, from a number of sectors underground, each sector being in effect a large-scale mine in its own right. This mining activity has faced challenges over the course of the last century such as:the capacity of the underground mine has been expanded to maintain and increase output of fine copper; the increasing size of the ore fragmentation forced to change the mining method to achieve the high productivity and profitability required in the business; and to modify the mining methods to continue mining at depth with safety. Fundamental activities in these mining methods, for the successful initiation of caving and subsequent draw, are:undercutting the base of the block or panel by blasting; and excavating of drawbells. The undercutting design evolves mainly on the height of the blasting to manage the change on ore fragmentation. The methodology move away from incorporating massive areas, typical of the block caving method, to a continuos blasting, typical of the panel caving method. Drawbell design changes on geometry, dimensions and sequence of excavation to deal with a corse ore fragmentation and the resolution of mining difficulties in the form of major rock bursts and collapses of production facilities. This paper focuses upon the evolution of the undercutting and drawbell design used at El Teniente mine and techniques under consideration to deal with future caving operations to provide the bulk of the daily production for the foreseeable future.

Jan 1, 2000

By AIME AIME

IN ACCORDANCE with the provisions of the Rules of Procedure of the American Engineering Standards Committee, the American Society for Testing, Mate-. on Feb. 15, 1921, submitted for approval by the A. E. S. Committee certain Standard Specifications for Copper, all of which were adopted or in process prior to Jan. 1, 1920, and sent with the standards the following histories of development and statements of use. FOR SOFT OR ANNEALED COPPER WIRE (B3-15) These specifications were originaly adopted by. the American Society for Testing Materials in 1912. They were prepared by a committee of the Society designated as Committee B-1 on Copper Wire. The committee consisted of eleven members; representatives of five manufacturers of -copper wire, of four manufacturers of electrical apparatus, and of two firms of consulting and contracting engineers. The members of the committee were designated by the officials of the companies to act as their representatives in the committee.

Jan 1, 1921

By M. Reza Saberi, T. Ted Miyake

Driven piles are a common tool in any engineer’s toolbox for supporting large structures over very soft ground, especially in high seismic risk zones. Challenges include achieving sufficient vertical and lateral load capacities within the constraints of pile spacing and geologic conditions. This was the case for a project in Orange County, California with a state-of-the-art, $180 million plant for biosolids processing, biogas management and energy recovery located in marshland next to an existing waste water treatment plant. The new construction for the Irvine Ranch Water District included a 70-foot (21 m) tall building and three closely spaced, 90-foot (27 m) high, 65-foot (20 m) diameter, egg-shaped steel digester tanks. The lower 35-feet (11 m) of the tanks were constructed below ground level. The site was underlain by up to 45 feet (14 m) of highly compressible peat and organic clays with standard penetration test (SPT) blows as low as 2 blows/ft (30 cm). Some of the peat layers had measured in-situ dry densities of less than 30 pcf (480 kg/m3) with moisture contents of over 250 percent. The soft clays and peat were underlain by a dense layer of sand and gravel at depth. Groundwater was very shallow. While nearby sites were designated by others as seismic site class “D”, this site was clearly class “F” (SF) which required site specific seismic hazard and time history analyses. Six recorded time histories were selected from the 1994 Northridge, 1989 Loma Prieta (California) and 1999 Chi Chi (Taiwan) earthquakes for the ground motion analysis considering the magnitude of the earthquake, distance to the source, characteristics of the earthquake source (i.e. type of fault displacement), peak ground acceleration, local site geology, station type (i.e. free-field or small structure stations), and spectral content that was similar to the period range of interest. Following ASCE’s Guideline Document 7-05, a site-specific horizontal acceleration response spectra (ARS) was developed for the maximum credible earthquake (MCE) associated with the site.

Jan 1, 2018